diff options
Diffstat (limited to 'drivers/ata/pata_cs5520.c')
| -rw-r--r-- | drivers/ata/pata_cs5520.c | 336 |
1 files changed, 336 insertions, 0 deletions
diff --git a/drivers/ata/pata_cs5520.c b/drivers/ata/pata_cs5520.c new file mode 100644 index 0000000..792ce48 --- /dev/null +++ b/drivers/ata/pata_cs5520.c @@ -0,0 +1,336 @@ +/* + * IDE tuning and bus mastering support for the CS5510/CS5520 + * chipsets + * + * The CS5510/CS5520 are slightly unusual devices. Unlike the + * typical IDE controllers they do bus mastering with the drive in + * PIO mode and smarter silicon. + * + * The practical upshot of this is that we must always tune the + * drive for the right PIO mode. We must also ignore all the blacklists + * and the drive bus mastering DMA information. Also to confuse matters + * further we can do DMA on PIO only drives. + * + * DMA on the 5510 also requires we disable_hlt() during DMA on early + * revisions. + * + * *** This driver is strictly experimental *** + * + * (c) Copyright Red Hat Inc 2002 + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2, or (at your option) any + * later version. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + * + * Documentation: + * Not publically available. + */ +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> + +#define DRV_NAME "pata_cs5520" +#define DRV_VERSION "0.6.2" + +struct pio_clocks +{ + int address; + int assert; + int recovery; +}; + +static const struct pio_clocks cs5520_pio_clocks[]={ + {3, 6, 11}, + {2, 5, 6}, + {1, 4, 3}, + {1, 3, 2}, + {1, 2, 1} +}; + +/** + * cs5520_set_timings - program PIO timings + * @ap: ATA port + * @adev: ATA device + * + * Program the PIO mode timings for the controller according to the pio + * clocking table. + */ + +static void cs5520_set_timings(struct ata_port *ap, struct ata_device *adev, int pio) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int slave = adev->devno; + + pio -= XFER_PIO_0; + + /* Channel command timing */ + pci_write_config_byte(pdev, 0x62 + ap->port_no, + (cs5520_pio_clocks[pio].recovery << 4) | + (cs5520_pio_clocks[pio].assert)); + /* FIXME: should these use address ? */ + /* Read command timing */ + pci_write_config_byte(pdev, 0x64 + 4*ap->port_no + slave, + (cs5520_pio_clocks[pio].recovery << 4) | + (cs5520_pio_clocks[pio].assert)); + /* Write command timing */ + pci_write_config_byte(pdev, 0x66 + 4*ap->port_no + slave, + (cs5520_pio_clocks[pio].recovery << 4) | + (cs5520_pio_clocks[pio].assert)); +} + +/** + * cs5520_enable_dma - turn on DMA bits + * + * Turn on the DMA bits for this disk. Needed because the BIOS probably + * has not done the work for us. Belongs in the core SATA code. + */ + +static void cs5520_enable_dma(struct ata_port *ap, struct ata_device *adev) +{ + /* Set the DMA enable/disable flag */ + u8 reg = inb(ap->ioaddr.bmdma_addr + 0x02); + reg |= 1<<(adev->devno + 5); + outb(reg, ap->ioaddr.bmdma_addr + 0x02); +} + +/** + * cs5520_set_dmamode - program DMA timings + * @ap: ATA port + * @adev: ATA device + * + * Program the DMA mode timings for the controller according to the pio + * clocking table. Note that this device sets the DMA timings to PIO + * mode values. This may seem bizarre but the 5520 architecture talks + * PIO mode to the disk and DMA mode to the controller so the underlying + * transfers are PIO timed. + */ + +static void cs5520_set_dmamode(struct ata_port *ap, struct ata_device *adev) +{ + static const int dma_xlate[3] = { XFER_PIO_0, XFER_PIO_3, XFER_PIO_4 }; + cs5520_set_timings(ap, adev, dma_xlate[adev->dma_mode]); + cs5520_enable_dma(ap, adev); +} + +/** + * cs5520_set_piomode - program PIO timings + * @ap: ATA port + * @adev: ATA device + * + * Program the PIO mode timings for the controller according to the pio + * clocking table. We know pio_mode will equal dma_mode because of the + * CS5520 architecture. At least once we turned DMA on and wrote a + * mode setter. + */ + +static void cs5520_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + cs5520_set_timings(ap, adev, adev->pio_mode); +} + + +static int cs5520_pre_reset(struct ata_port *ap) +{ + ap->cbl = ATA_CBL_PATA40; + return ata_std_prereset(ap); +} + +static void cs5520_error_handler(struct ata_port *ap) +{ + return ata_bmdma_drive_eh(ap, cs5520_pre_reset, ata_std_softreset, NULL, ata_std_postreset); +} + +static struct scsi_host_template cs5520_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, +}; + +static struct ata_port_operations cs5520_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = cs5520_set_piomode, + .set_dmamode = cs5520_set_dmamode, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = cs5520_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .data_xfer = ata_pio_data_xfer, + + .eng_timeout = ata_eng_timeout, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop, +}; + +static int __devinit cs5520_init_one(struct pci_dev *dev, const struct pci_device_id *id) +{ + u8 pcicfg; + static struct ata_probe_ent probe[2]; + int ports = 0; + + /* IDE port enable bits */ + pci_read_config_byte(dev, 0x60, &pcicfg); + + /* Check if the ATA ports are enabled */ + if ((pcicfg & 3) == 0) + return -ENODEV; + + if ((pcicfg & 0x40) == 0) { + printk(KERN_WARNING DRV_NAME ": DMA mode disabled. Enabling.\n"); + pci_write_config_byte(dev, 0x60, pcicfg | 0x40); + } + + /* Perform set up for DMA */ + if (pci_enable_device_bars(dev, 1<<2)) { + printk(KERN_ERR DRV_NAME ": unable to configure BAR2.\n"); + return -ENODEV; + } + pci_set_master(dev); + if (pci_set_dma_mask(dev, DMA_32BIT_MASK)) { + printk(KERN_ERR DRV_NAME ": unable to configure DMA mask.\n"); + return -ENODEV; + } + if (pci_set_consistent_dma_mask(dev, DMA_32BIT_MASK)) { + printk(KERN_ERR DRV_NAME ": unable to configure consistent DMA mask.\n"); + return -ENODEV; + } + + /* We have to do our own plumbing as the PCI setup for this + chipset is non-standard so we can't punt to the libata code */ + + INIT_LIST_HEAD(&probe[0].node); + probe[0].dev = pci_dev_to_dev(dev); + probe[0].port_ops = &cs5520_port_ops; + probe[0].sht = &cs5520_sht; + probe[0].pio_mask = 0x1F; + probe[0].mwdma_mask = id->driver_data; + probe[0].irq = 14; + probe[0].irq_flags = 0; + probe[0].port_flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST; + probe[0].n_ports = 1; + probe[0].port[0].cmd_addr = 0x1F0; + probe[0].port[0].ctl_addr = 0x3F6; + probe[0].port[0].altstatus_addr = 0x3F6; + probe[0].port[0].bmdma_addr = pci_resource_start(dev, 2); + + /* The secondary lurks at different addresses but is otherwise + the same beastie */ + + probe[1] = probe[0]; + INIT_LIST_HEAD(&probe[1].node); + probe[1].irq = 15; + probe[1].port[0].cmd_addr = 0x170; + probe[1].port[0].ctl_addr = 0x376; + probe[1].port[0].altstatus_addr = 0x376; + probe[1].port[0].bmdma_addr = pci_resource_start(dev, 2) + 8; + + /* Let libata fill in the port details */ + ata_std_ports(&probe[0].port[0]); + ata_std_ports(&probe[1].port[0]); + + /* Now add the ports that are active */ + if (pcicfg & 1) + ports += ata_device_add(&probe[0]); + if (pcicfg & 2) + ports += ata_device_add(&probe[1]); + if (ports) + return 0; + return -ENODEV; +} + +/** + * cs5520_remove_one - device unload + * @pdev: PCI device being removed + * + * Handle an unplug/unload event for a PCI device. Unload the + * PCI driver but do not use the default handler as we manage + * resources ourself and *MUST NOT* disable the device as it has + * other functions. + */ + +static void __devexit cs5520_remove_one(struct pci_dev *pdev) +{ + struct device *dev = pci_dev_to_dev(pdev); + struct ata_host *host = dev_get_drvdata(dev); + + ata_host_remove(host); + dev_set_drvdata(dev, NULL); +} + +/* For now keep DMA off. We can set it for all but A rev CS5510 once the + core ATA code can handle it */ + +static struct pci_device_id pata_cs5520[] = { + { PCI_DEVICE(PCI_VENDOR_ID_CYRIX, PCI_DEVICE_ID_CYRIX_5510), }, + { PCI_DEVICE(PCI_VENDOR_ID_CYRIX, PCI_DEVICE_ID_CYRIX_5520), }, + { 0, }, +}; + +static struct pci_driver cs5520_pci_driver = { + .name = DRV_NAME, + .id_table = pata_cs5520, + .probe = cs5520_init_one, + .remove = cs5520_remove_one +}; + + +static int __init cs5520_init(void) +{ + return pci_register_driver(&cs5520_pci_driver); +} + +static void __exit cs5520_exit(void) +{ + pci_unregister_driver(&cs5520_pci_driver); +} + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("low-level driver for Cyrix CS5510/5520"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, pata_cs5520); +MODULE_VERSION(DRV_VERSION); + +module_init(cs5520_init); +module_exit(cs5520_exit); + |
