summaryrefslogtreecommitdiffstats
path: root/arch
diff options
context:
space:
mode:
Diffstat (limited to 'arch')
-rw-r--r--arch/arm/mach-lpc32xx/phy3250.c7
-rw-r--r--arch/arm/mach-u300/dummyspichip.c5
-rw-r--r--arch/arm/mach-u300/spi.c10
-rw-r--r--arch/arm/mach-ux500/board-mop500.c8
-rw-r--r--arch/arm/plat-samsung/include/plat/s3c64xx-spi.h3
-rw-r--r--arch/blackfin/include/asm/bfin5xx_spi.h81
-rw-r--r--arch/powerpc/boot/dts/mpc8536ds.dts52
-rw-r--r--arch/powerpc/boot/dts/p4080ds.dts11
8 files changed, 72 insertions, 105 deletions
diff --git a/arch/arm/mach-lpc32xx/phy3250.c b/arch/arm/mach-lpc32xx/phy3250.c
index bc9a42d..0c936cf 100644
--- a/arch/arm/mach-lpc32xx/phy3250.c
+++ b/arch/arm/mach-lpc32xx/phy3250.c
@@ -172,18 +172,12 @@ static void phy3250_spi_cs_set(u32 control)
}
static struct pl022_config_chip spi0_chip_info = {
- .lbm = LOOPBACK_DISABLED,
.com_mode = INTERRUPT_TRANSFER,
.iface = SSP_INTERFACE_MOTOROLA_SPI,
.hierarchy = SSP_MASTER,
.slave_tx_disable = 0,
- .endian_tx = SSP_TX_LSB,
- .endian_rx = SSP_RX_LSB,
- .data_size = SSP_DATA_BITS_8,
.rx_lev_trig = SSP_RX_4_OR_MORE_ELEM,
.tx_lev_trig = SSP_TX_4_OR_MORE_EMPTY_LOC,
- .clk_phase = SSP_CLK_FIRST_EDGE,
- .clk_pol = SSP_CLK_POL_IDLE_LOW,
.ctrl_len = SSP_BITS_8,
.wait_state = SSP_MWIRE_WAIT_ZERO,
.duplex = SSP_MICROWIRE_CHANNEL_FULL_DUPLEX,
@@ -239,6 +233,7 @@ static int __init phy3250_spi_board_register(void)
.max_speed_hz = 5000000,
.bus_num = 0,
.chip_select = 0,
+ .mode = SPI_MODE_0,
.platform_data = &eeprom,
.controller_data = &spi0_chip_info,
},
diff --git a/arch/arm/mach-u300/dummyspichip.c b/arch/arm/mach-u300/dummyspichip.c
index 5f55012..03f7936 100644
--- a/arch/arm/mach-u300/dummyspichip.c
+++ b/arch/arm/mach-u300/dummyspichip.c
@@ -46,7 +46,6 @@ static ssize_t dummy_looptest(struct device *dev,
* struct, this is just used here to alter the behaviour of the chip
* in order to perform tests.
*/
- struct pl022_config_chip *chip_info = spi->controller_data;
int status;
u8 txbuf[14] = {0xDE, 0xAD, 0xBE, 0xEF, 0x2B, 0xAD,
0xCA, 0xFE, 0xBA, 0xBE, 0xB1, 0x05,
@@ -72,7 +71,7 @@ static ssize_t dummy_looptest(struct device *dev,
* Force chip to 8 bit mode
* WARNING: NEVER DO THIS IN REAL DRIVER CODE, THIS SHOULD BE STATIC!
*/
- chip_info->data_size = SSP_DATA_BITS_8;
+ spi->bits_per_word = 8;
/* You should NOT DO THIS EITHER */
spi->master->setup(spi);
@@ -159,7 +158,7 @@ static ssize_t dummy_looptest(struct device *dev,
* Force chip to 16 bit mode
* WARNING: NEVER DO THIS IN REAL DRIVER CODE, THIS SHOULD BE STATIC!
*/
- chip_info->data_size = SSP_DATA_BITS_16;
+ spi->bits_per_word = 16;
/* You should NOT DO THIS EITHER */
spi->master->setup(spi);
diff --git a/arch/arm/mach-u300/spi.c b/arch/arm/mach-u300/spi.c
index f0e887b..edb2c0d 100644
--- a/arch/arm/mach-u300/spi.c
+++ b/arch/arm/mach-u300/spi.c
@@ -30,8 +30,6 @@ static void select_dummy_chip(u32 chipselect)
}
struct pl022_config_chip dummy_chip_info = {
- /* Nominally this is LOOPBACK_DISABLED, but this is our dummy chip! */
- .lbm = LOOPBACK_ENABLED,
/*
* available POLLING_TRANSFER and INTERRUPT_TRANSFER,
* DMA_TRANSFER does not work
@@ -42,14 +40,8 @@ struct pl022_config_chip dummy_chip_info = {
.hierarchy = SSP_MASTER,
/* 0 = drive TX even as slave, 1 = do not drive TX as slave */
.slave_tx_disable = 0,
- /* LSB first */
- .endian_tx = SSP_TX_LSB,
- .endian_rx = SSP_RX_LSB,
- .data_size = SSP_DATA_BITS_8, /* used to be 12 in some default */
.rx_lev_trig = SSP_RX_1_OR_MORE_ELEM,
.tx_lev_trig = SSP_TX_1_OR_MORE_EMPTY_LOC,
- .clk_phase = SSP_CLK_SECOND_EDGE,
- .clk_pol = SSP_CLK_POL_IDLE_LOW,
.ctrl_len = SSP_BITS_12,
.wait_state = SSP_MWIRE_WAIT_ZERO,
.duplex = SSP_MICROWIRE_CHANNEL_FULL_DUPLEX,
@@ -75,7 +67,7 @@ static struct spi_board_info u300_spi_devices[] = {
.bus_num = 0, /* Only one bus on this chip */
.chip_select = 0,
/* Means SPI_CS_HIGH, change if e.g low CS */
- .mode = 0,
+ .mode = SPI_MODE_1 | SPI_LSB_FIRST | SPI_LOOP,
},
#endif
};
diff --git a/arch/arm/mach-ux500/board-mop500.c b/arch/arm/mach-ux500/board-mop500.c
index 0e8fd13..219ae0c 100644
--- a/arch/arm/mach-ux500/board-mop500.c
+++ b/arch/arm/mach-ux500/board-mop500.c
@@ -55,19 +55,13 @@ static void ab4500_spi_cs_control(u32 command)
}
struct pl022_config_chip ab4500_chip_info = {
- .lbm = LOOPBACK_DISABLED,
.com_mode = INTERRUPT_TRANSFER,
.iface = SSP_INTERFACE_MOTOROLA_SPI,
/* we can act as master only */
.hierarchy = SSP_MASTER,
.slave_tx_disable = 0,
- .endian_rx = SSP_RX_MSB,
- .endian_tx = SSP_TX_MSB,
- .data_size = SSP_DATA_BITS_24,
.rx_lev_trig = SSP_RX_1_OR_MORE_ELEM,
.tx_lev_trig = SSP_TX_1_OR_MORE_EMPTY_LOC,
- .clk_phase = SSP_CLK_SECOND_EDGE,
- .clk_pol = SSP_CLK_POL_IDLE_HIGH,
.cs_control = ab4500_spi_cs_control,
};
@@ -83,7 +77,7 @@ static struct spi_board_info u8500_spi_devices[] = {
.max_speed_hz = 12000000,
.bus_num = 0,
.chip_select = 0,
- .mode = SPI_MODE_0,
+ .mode = SPI_MODE_3,
.irq = IRQ_DB8500_AB8500,
},
};
diff --git a/arch/arm/plat-samsung/include/plat/s3c64xx-spi.h b/arch/arm/plat-samsung/include/plat/s3c64xx-spi.h
index e5aba8f..b226f740 100644
--- a/arch/arm/plat-samsung/include/plat/s3c64xx-spi.h
+++ b/arch/arm/plat-samsung/include/plat/s3c64xx-spi.h
@@ -32,6 +32,8 @@ struct s3c64xx_spi_csinfo {
* struct s3c64xx_spi_info - SPI Controller defining structure
* @src_clk_nr: Clock source index for the CLK_CFG[SPI_CLKSEL] field.
* @src_clk_name: Platform name of the corresponding clock.
+ * @clk_from_cmu: If the SPI clock/prescalar control block is present
+ * by the platform's clock-management-unit and not in SPI controller.
* @num_cs: Number of CS this controller emulates.
* @cfg_gpio: Configure pins for this SPI controller.
* @fifo_lvl_mask: All tx fifo_lvl fields start at offset-6
@@ -41,6 +43,7 @@ struct s3c64xx_spi_csinfo {
struct s3c64xx_spi_info {
int src_clk_nr;
char *src_clk_name;
+ bool clk_from_cmu;
int num_cs;
diff --git a/arch/blackfin/include/asm/bfin5xx_spi.h b/arch/blackfin/include/asm/bfin5xx_spi.h
index ed4f8c6..4223cf0 100644
--- a/arch/blackfin/include/asm/bfin5xx_spi.h
+++ b/arch/blackfin/include/asm/bfin5xx_spi.h
@@ -11,26 +11,17 @@
#define MIN_SPI_BAUD_VAL 2
-#define SPI_READ 0
-#define SPI_WRITE 1
-
-#define SPI_CTRL_OFF 0x0
-#define SPI_FLAG_OFF 0x4
-#define SPI_STAT_OFF 0x8
-#define SPI_TXBUFF_OFF 0xc
-#define SPI_RXBUFF_OFF 0x10
-#define SPI_BAUD_OFF 0x14
-#define SPI_SHAW_OFF 0x18
-
-
#define BIT_CTL_ENABLE 0x4000
#define BIT_CTL_OPENDRAIN 0x2000
#define BIT_CTL_MASTER 0x1000
-#define BIT_CTL_POLAR 0x0800
-#define BIT_CTL_PHASE 0x0400
-#define BIT_CTL_BITORDER 0x0200
+#define BIT_CTL_CPOL 0x0800
+#define BIT_CTL_CPHA 0x0400
+#define BIT_CTL_LSBF 0x0200
#define BIT_CTL_WORDSIZE 0x0100
-#define BIT_CTL_MISOENABLE 0x0020
+#define BIT_CTL_EMISO 0x0020
+#define BIT_CTL_PSSE 0x0010
+#define BIT_CTL_GM 0x0008
+#define BIT_CTL_SZ 0x0004
#define BIT_CTL_RXMOD 0x0000
#define BIT_CTL_TXMOD 0x0001
#define BIT_CTL_TIMOD_DMA_TX 0x0003
@@ -50,61 +41,7 @@
#define BIT_STU_SENDOVER 0x0001
#define BIT_STU_RECVFULL 0x0020
-#define CFG_SPI_ENABLE 1
-#define CFG_SPI_DISABLE 0
-
-#define CFG_SPI_OUTENABLE 1
-#define CFG_SPI_OUTDISABLE 0
-
-#define CFG_SPI_ACTLOW 1
-#define CFG_SPI_ACTHIGH 0
-
-#define CFG_SPI_PHASESTART 1
-#define CFG_SPI_PHASEMID 0
-
-#define CFG_SPI_MASTER 1
-#define CFG_SPI_SLAVE 0
-
-#define CFG_SPI_SENELAST 0
-#define CFG_SPI_SENDZERO 1
-
-#define CFG_SPI_RCVFLUSH 1
-#define CFG_SPI_RCVDISCARD 0
-
-#define CFG_SPI_LSBFIRST 1
-#define CFG_SPI_MSBFIRST 0
-
-#define CFG_SPI_WORDSIZE16 1
-#define CFG_SPI_WORDSIZE8 0
-
-#define CFG_SPI_MISOENABLE 1
-#define CFG_SPI_MISODISABLE 0
-
-#define CFG_SPI_READ 0x00
-#define CFG_SPI_WRITE 0x01
-#define CFG_SPI_DMAREAD 0x02
-#define CFG_SPI_DMAWRITE 0x03
-
-#define CFG_SPI_CSCLEARALL 0
-#define CFG_SPI_CHIPSEL1 1
-#define CFG_SPI_CHIPSEL2 2
-#define CFG_SPI_CHIPSEL3 3
-#define CFG_SPI_CHIPSEL4 4
-#define CFG_SPI_CHIPSEL5 5
-#define CFG_SPI_CHIPSEL6 6
-#define CFG_SPI_CHIPSEL7 7
-
-#define CFG_SPI_CS1VALUE 1
-#define CFG_SPI_CS2VALUE 2
-#define CFG_SPI_CS3VALUE 3
-#define CFG_SPI_CS4VALUE 4
-#define CFG_SPI_CS5VALUE 5
-#define CFG_SPI_CS6VALUE 6
-#define CFG_SPI_CS7VALUE 7
-
-#define CMD_SPI_SET_BAUDRATE 2
-#define CMD_SPI_GET_SYSTEMCLOCK 25
-#define CMD_SPI_SET_WRITECONTINUOUS 26
+#define MAX_CTRL_CS 8 /* cs in spi controller */
/* device.platform_data for SSP controller devices */
struct bfin5xx_spi_master {
@@ -120,9 +57,7 @@ struct bfin5xx_spi_chip {
u16 ctl_reg;
u8 enable_dma;
u8 bits_per_word;
- u8 cs_change_per_word;
u16 cs_chg_udelay; /* Some devices require 16-bit delays */
- u32 cs_gpio;
/* Value to send if no TX value is supplied, usually 0x0 or 0xFFFF */
u16 idle_tx_val;
u8 pio_interrupt; /* Enable spi data irq */
diff --git a/arch/powerpc/boot/dts/mpc8536ds.dts b/arch/powerpc/boot/dts/mpc8536ds.dts
index 815cebb..a75c10e 100644
--- a/arch/powerpc/boot/dts/mpc8536ds.dts
+++ b/arch/powerpc/boot/dts/mpc8536ds.dts
@@ -108,6 +108,58 @@
};
};
+ spi@7000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,mpc8536-espi";
+ reg = <0x7000 0x1000>;
+ interrupts = <59 0x2>;
+ interrupt-parent = <&mpic>;
+ fsl,espi-num-chipselects = <4>;
+
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spansion,s25sl12801";
+ reg = <0>;
+ spi-max-frequency = <40000000>;
+ partition@u-boot {
+ label = "u-boot";
+ reg = <0x00000000 0x00100000>;
+ read-only;
+ };
+ partition@kernel {
+ label = "kernel";
+ reg = <0x00100000 0x00500000>;
+ read-only;
+ };
+ partition@dtb {
+ label = "dtb";
+ reg = <0x00600000 0x00100000>;
+ read-only;
+ };
+ partition@fs {
+ label = "file system";
+ reg = <0x00700000 0x00900000>;
+ };
+ };
+ flash@1 {
+ compatible = "spansion,s25sl12801";
+ reg = <1>;
+ spi-max-frequency = <40000000>;
+ };
+ flash@2 {
+ compatible = "spansion,s25sl12801";
+ reg = <2>;
+ spi-max-frequency = <40000000>;
+ };
+ flash@3 {
+ compatible = "spansion,s25sl12801";
+ reg = <3>;
+ spi-max-frequency = <40000000>;
+ };
+ };
+
dma@21300 {
#address-cells = <1>;
#size-cells = <1>;
diff --git a/arch/powerpc/boot/dts/p4080ds.dts b/arch/powerpc/boot/dts/p4080ds.dts
index 2f0de24..5b7fc29 100644
--- a/arch/powerpc/boot/dts/p4080ds.dts
+++ b/arch/powerpc/boot/dts/p4080ds.dts
@@ -236,22 +236,19 @@
};
spi@110000 {
- cell-index = <0>;
#address-cells = <1>;
#size-cells = <0>;
- compatible = "fsl,espi";
+ compatible = "fsl,p4080-espi", "fsl,mpc8536-espi";
reg = <0x110000 0x1000>;
interrupts = <53 0x2>;
interrupt-parent = <&mpic>;
- espi,num-ss-bits = <4>;
- mode = "cpu";
+ fsl,espi-num-chipselects = <4>;
- fsl_m25p80@0 {
+ flash@0 {
#address-cells = <1>;
#size-cells = <1>;
- compatible = "fsl,espi-flash";
+ compatible = "spansion,s25sl12801";
reg = <0>;
- linux,modalias = "fsl_m25p80";
spi-max-frequency = <40000000>; /* input clock */
partition@u-boot {
label = "u-boot";
OpenPOWER on IntegriCloud