diff options
Diffstat (limited to 'arch')
59 files changed, 0 insertions, 2511 deletions
diff --git a/arch/mips/Kconfig b/arch/mips/Kconfig index a29ebfd..cba171a 100644 --- a/arch/mips/Kconfig +++ b/arch/mips/Kconfig @@ -276,24 +276,6 @@ config MOMENCO_OCELOT_3 The Ocelot-3 is based off Discovery III System Controller and PMC-Sierra Rm79000 core. -config MOMENCO_OCELOT_C - bool "Momentum Ocelot-C board" - select DMA_NONCOHERENT - select HW_HAS_PCI - select IRQ_CPU - select IRQ_MV64340 - select PCI_MARVELL - select RM7000_CPU_SCACHE - select SWAP_IO_SPACE - select SYS_HAS_CPU_RM7000 - select SYS_SUPPORTS_32BIT_KERNEL - select SYS_SUPPORTS_64BIT_KERNEL - select SYS_SUPPORTS_BIG_ENDIAN - select GENERIC_HARDIRQS_NO__DO_IRQ - help - The Ocelot is a MIPS-based Single Board Computer (SBC) made by - Momentum Computer <http://www.momenco.com/>. - config PNX8550_JBS bool "Philips PNX8550 based JBS board" select PNX8550 diff --git a/arch/mips/Makefile b/arch/mips/Makefile index ddb048b..fc09769 100644 --- a/arch/mips/Makefile +++ b/arch/mips/Makefile @@ -335,14 +335,6 @@ cflags-$(CONFIG_MOMENCO_OCELOT) += -Iinclude/asm-mips/mach-ocelot load-$(CONFIG_MOMENCO_OCELOT) += 0xffffffff80100000 # -# Momentum Ocelot-C and -CS boards -# -# The Ocelot-C[S] setup.o must be linked early - it does the ioremap() for the -# mips_io_port_base. -core-$(CONFIG_MOMENCO_OCELOT_C) += arch/mips/momentum/ocelot_c/ -load-$(CONFIG_MOMENCO_OCELOT_C) += 0xffffffff80100000 - -# # PMC-Sierra Yosemite # core-$(CONFIG_PMC_YOSEMITE) += arch/mips/pmc-sierra/yosemite/ diff --git a/arch/mips/configs/atlas_defconfig b/arch/mips/configs/atlas_defconfig index 99c54f3..de855d1 100644 --- a/arch/mips/configs/atlas_defconfig +++ b/arch/mips/configs/atlas_defconfig @@ -35,7 +35,6 @@ CONFIG_MIPS_ATLAS=y # CONFIG_MOMENCO_JAGUAR_ATX is not set # CONFIG_MOMENCO_OCELOT is not set # CONFIG_MOMENCO_OCELOT_3 is not set -# CONFIG_MOMENCO_OCELOT_C is not set # CONFIG_MOMENCO_OCELOT_G is not set # CONFIG_MIPS_XXS1500 is not set # CONFIG_PNX8550_JBS is not set diff --git a/arch/mips/configs/bigsur_defconfig b/arch/mips/configs/bigsur_defconfig index c885e4f..bf88a6c 100644 --- a/arch/mips/configs/bigsur_defconfig +++ b/arch/mips/configs/bigsur_defconfig @@ -35,7 +35,6 @@ CONFIG_ZONE_DMA=y # CONFIG_MOMENCO_JAGUAR_ATX is not set # CONFIG_MOMENCO_OCELOT is not set # CONFIG_MOMENCO_OCELOT_3 is not set -# CONFIG_MOMENCO_OCELOT_C is not set # CONFIG_MOMENCO_OCELOT_G is not set # CONFIG_MIPS_XXS1500 is not set # CONFIG_PNX8550_JBS is not set diff --git a/arch/mips/configs/capcella_defconfig b/arch/mips/configs/capcella_defconfig index a5ebedc..7582709 100644 --- a/arch/mips/configs/capcella_defconfig +++ b/arch/mips/configs/capcella_defconfig @@ -35,7 +35,6 @@ CONFIG_ZONE_DMA=y # CONFIG_MOMENCO_JAGUAR_ATX is not set # CONFIG_MOMENCO_OCELOT is not set # CONFIG_MOMENCO_OCELOT_3 is not set -# CONFIG_MOMENCO_OCELOT_C is not set # CONFIG_MOMENCO_OCELOT_G is not set # CONFIG_MIPS_XXS1500 is not set # CONFIG_PNX8550_JBS is not set diff --git a/arch/mips/configs/cobalt_defconfig b/arch/mips/configs/cobalt_defconfig index c70456e..9c5750c 100644 --- a/arch/mips/configs/cobalt_defconfig +++ b/arch/mips/configs/cobalt_defconfig @@ -21,7 +21,6 @@ CONFIG_MIPS_COBALT=y # CONFIG_MIPS_SIM is not set # CONFIG_MOMENCO_OCELOT is not set # CONFIG_MOMENCO_OCELOT_3 is not set -# CONFIG_MOMENCO_OCELOT_C is not set # CONFIG_PNX8550_JBS is not set # CONFIG_PNX8550_STB810 is not set # CONFIG_DDB5477 is not set diff --git a/arch/mips/configs/db1000_defconfig b/arch/mips/configs/db1000_defconfig index 87e99e5..bbf007a 100644 --- a/arch/mips/configs/db1000_defconfig +++ b/arch/mips/configs/db1000_defconfig @@ -36,7 +36,6 @@ CONFIG_MIPS_DB1000=y # CONFIG_MOMENCO_JAGUAR_ATX is not set # CONFIG_MOMENCO_OCELOT is not set # CONFIG_MOMENCO_OCELOT_3 is not set -# CONFIG_MOMENCO_OCELOT_C is not set # CONFIG_MOMENCO_OCELOT_G is not set # CONFIG_MIPS_XXS1500 is not set # CONFIG_PNX8550_JBS is not set diff --git a/arch/mips/configs/db1100_defconfig b/arch/mips/configs/db1100_defconfig index 5d46a99..384e41a 100644 --- a/arch/mips/configs/db1100_defconfig +++ b/arch/mips/configs/db1100_defconfig @@ -36,7 +36,6 @@ CONFIG_MIPS_DB1100=y # CONFIG_MOMENCO_JAGUAR_ATX is not set # CONFIG_MOMENCO_OCELOT is not set # CONFIG_MOMENCO_OCELOT_3 is not set -# CONFIG_MOMENCO_OCELOT_C is not set # CONFIG_MOMENCO_OCELOT_G is not set # CONFIG_MIPS_XXS1500 is not set # CONFIG_PNX8550_JBS is not set diff --git a/arch/mips/configs/db1200_defconfig b/arch/mips/configs/db1200_defconfig index e6f4242..76c3c46 100644 --- a/arch/mips/configs/db1200_defconfig +++ b/arch/mips/configs/db1200_defconfig @@ -36,7 +36,6 @@ CONFIG_MIPS_DB1200=y # CONFIG_MOMENCO_JAGUAR_ATX is not set # CONFIG_MOMENCO_OCELOT is not set # CONFIG_MOMENCO_OCELOT_3 is not set -# CONFIG_MOMENCO_OCELOT_C is not set # CONFIG_MOMENCO_OCELOT_G is not set # CONFIG_MIPS_XXS1500 is not set # CONFIG_PNX8550_JBS is not set diff --git a/arch/mips/configs/db1500_defconfig b/arch/mips/configs/db1500_defconfig index ea56093..89c4580 100644 --- a/arch/mips/configs/db1500_defconfig +++ b/arch/mips/configs/db1500_defconfig @@ -36,7 +36,6 @@ CONFIG_MIPS_DB1500=y # CONFIG_MOMENCO_JAGUAR_ATX is not set # CONFIG_MOMENCO_OCELOT is not set # CONFIG_MOMENCO_OCELOT_3 is not set -# CONFIG_MOMENCO_OCELOT_C is not set # CONFIG_MOMENCO_OCELOT_G is not set # CONFIG_MIPS_XXS1500 is not set # CONFIG_PNX8550_JBS is not set diff --git a/arch/mips/configs/db1550_defconfig b/arch/mips/configs/db1550_defconfig index 2728a00..c83ba3c 100644 --- a/arch/mips/configs/db1550_defconfig +++ b/arch/mips/configs/db1550_defconfig @@ -36,7 +36,6 @@ CONFIG_MIPS_DB1550=y # CONFIG_MOMENCO_JAGUAR_ATX is not set # CONFIG_MOMENCO_OCELOT is not set # CONFIG_MOMENCO_OCELOT_3 is not set -# CONFIG_MOMENCO_OCELOT_C is not set # CONFIG_MOMENCO_OCELOT_G is not set # CONFIG_MIPS_XXS1500 is not set # CONFIG_PNX8550_JBS is not set diff --git a/arch/mips/configs/ddb5477_defconfig b/arch/mips/configs/ddb5477_defconfig index d67f150..7ec230e 100644 --- a/arch/mips/configs/ddb5477_defconfig +++ b/arch/mips/configs/ddb5477_defconfig @@ -35,7 +35,6 @@ CONFIG_ZONE_DMA=y # CONFIG_MOMENCO_JAGUAR_ATX is not set # CONFIG_MOMENCO_OCELOT is not set # CONFIG_MOMENCO_OCELOT_3 is not set -# CONFIG_MOMENCO_OCELOT_C is not set # CONFIG_MOMENCO_OCELOT_G is not set # CONFIG_MIPS_XXS1500 is not set # CONFIG_PNX8550_JBS is not set diff --git a/arch/mips/configs/decstation_defconfig b/arch/mips/configs/decstation_defconfig index 25e5336..2a4948a 100644 --- a/arch/mips/configs/decstation_defconfig +++ b/arch/mips/configs/decstation_defconfig @@ -35,7 +35,6 @@ CONFIG_MACH_DECSTATION=y # CONFIG_MOMENCO_JAGUAR_ATX is not set # CONFIG_MOMENCO_OCELOT is not set # CONFIG_MOMENCO_OCELOT_3 is not set -# CONFIG_MOMENCO_OCELOT_C is not set # CONFIG_MOMENCO_OCELOT_G is not set # CONFIG_MIPS_XXS1500 is not set # CONFIG_PNX8550_JBS is not set diff --git a/arch/mips/configs/e55_defconfig b/arch/mips/configs/e55_defconfig index 1257a70..d853278 100644 --- a/arch/mips/configs/e55_defconfig +++ b/arch/mips/configs/e55_defconfig @@ -35,7 +35,6 @@ CONFIG_ZONE_DMA=y # CONFIG_MOMENCO_JAGUAR_ATX is not set # CONFIG_MOMENCO_OCELOT is not set # CONFIG_MOMENCO_OCELOT_3 is not set -# CONFIG_MOMENCO_OCELOT_C is not set # CONFIG_MOMENCO_OCELOT_G is not set # CONFIG_MIPS_XXS1500 is not set # CONFIG_PNX8550_JBS is not set diff --git a/arch/mips/configs/emma2rh_defconfig b/arch/mips/configs/emma2rh_defconfig index 9318fce..31f03f8 100644 --- a/arch/mips/configs/emma2rh_defconfig +++ b/arch/mips/configs/emma2rh_defconfig @@ -35,7 +35,6 @@ CONFIG_ZONE_DMA=y # CONFIG_MOMENCO_JAGUAR_ATX is not set # CONFIG_MOMENCO_OCELOT is not set # CONFIG_MOMENCO_OCELOT_3 is not set -# CONFIG_MOMENCO_OCELOT_C is not set # CONFIG_MOMENCO_OCELOT_G is not set # CONFIG_MIPS_XXS1500 is not set # CONFIG_PNX8550_JBS is not set diff --git a/arch/mips/configs/excite_defconfig b/arch/mips/configs/excite_defconfig index e35a8f5..b1a9e0b 100644 --- a/arch/mips/configs/excite_defconfig +++ b/arch/mips/configs/excite_defconfig @@ -36,7 +36,6 @@ CONFIG_BASLER_EXCITE=y # CONFIG_MOMENCO_JAGUAR_ATX is not set # CONFIG_MOMENCO_OCELOT is not set # CONFIG_MOMENCO_OCELOT_3 is not set -# CONFIG_MOMENCO_OCELOT_C is not set # CONFIG_MOMENCO_OCELOT_G is not set # CONFIG_MIPS_XXS1500 is not set # CONFIG_PNX8550_JBS is not set diff --git a/arch/mips/configs/ip22_defconfig b/arch/mips/configs/ip22_defconfig index c655d4d..2f22436 100644 --- a/arch/mips/configs/ip22_defconfig +++ b/arch/mips/configs/ip22_defconfig @@ -35,7 +35,6 @@ CONFIG_ZONE_DMA=y # CONFIG_MOMENCO_JAGUAR_ATX is not set # CONFIG_MOMENCO_OCELOT is not set # CONFIG_MOMENCO_OCELOT_3 is not set -# CONFIG_MOMENCO_OCELOT_C is not set # CONFIG_MOMENCO_OCELOT_G is not set # CONFIG_MIPS_XXS1500 is not set # CONFIG_PNX8550_JBS is not set diff --git a/arch/mips/configs/ip27_defconfig b/arch/mips/configs/ip27_defconfig index a2475e7..267af44 100644 --- a/arch/mips/configs/ip27_defconfig +++ b/arch/mips/configs/ip27_defconfig @@ -35,7 +35,6 @@ CONFIG_ZONE_DMA=y # CONFIG_MOMENCO_JAGUAR_ATX is not set # CONFIG_MOMENCO_OCELOT is not set # CONFIG_MOMENCO_OCELOT_3 is not set -# CONFIG_MOMENCO_OCELOT_C is not set # CONFIG_MOMENCO_OCELOT_G is not set # CONFIG_MIPS_XXS1500 is not set # CONFIG_PNX8550_JBS is not set diff --git a/arch/mips/configs/ip32_defconfig b/arch/mips/configs/ip32_defconfig index f95d5fe..00ec6ed 100644 --- a/arch/mips/configs/ip32_defconfig +++ b/arch/mips/configs/ip32_defconfig @@ -35,7 +35,6 @@ CONFIG_ZONE_DMA=y # CONFIG_MOMENCO_JAGUAR_ATX is not set # CONFIG_MOMENCO_OCELOT is not set # CONFIG_MOMENCO_OCELOT_3 is not set -# CONFIG_MOMENCO_OCELOT_C is not set # CONFIG_MOMENCO_OCELOT_G is not set # CONFIG_MIPS_XXS1500 is not set # CONFIG_PNX8550_JBS is not set diff --git a/arch/mips/configs/jazz_defconfig b/arch/mips/configs/jazz_defconfig index e2f5a5a..12c0265 100644 --- a/arch/mips/configs/jazz_defconfig +++ b/arch/mips/configs/jazz_defconfig @@ -35,7 +35,6 @@ CONFIG_MACH_JAZZ=y # CONFIG_MOMENCO_JAGUAR_ATX is not set # CONFIG_MOMENCO_OCELOT is not set # CONFIG_MOMENCO_OCELOT_3 is not set -# CONFIG_MOMENCO_OCELOT_C is not set # CONFIG_MOMENCO_OCELOT_G is not set # CONFIG_MIPS_XXS1500 is not set # CONFIG_PNX8550_JBS is not set diff --git a/arch/mips/configs/jmr3927_defconfig b/arch/mips/configs/jmr3927_defconfig index 2c88b32..61235a5 100644 --- a/arch/mips/configs/jmr3927_defconfig +++ b/arch/mips/configs/jmr3927_defconfig @@ -35,7 +35,6 @@ CONFIG_ZONE_DMA=y # CONFIG_MOMENCO_JAGUAR_ATX is not set # CONFIG_MOMENCO_OCELOT is not set # CONFIG_MOMENCO_OCELOT_3 is not set -# CONFIG_MOMENCO_OCELOT_C is not set # CONFIG_MOMENCO_OCELOT_G is not set # CONFIG_MIPS_XXS1500 is not set # CONFIG_PNX8550_JBS is not set diff --git a/arch/mips/configs/lasat200_defconfig b/arch/mips/configs/lasat200_defconfig index ccf7227..c427c08 100644 --- a/arch/mips/configs/lasat200_defconfig +++ b/arch/mips/configs/lasat200_defconfig @@ -35,7 +35,6 @@ CONFIG_LASAT=y # CONFIG_MOMENCO_JAGUAR_ATX is not set # CONFIG_MOMENCO_OCELOT is not set # CONFIG_MOMENCO_OCELOT_3 is not set -# CONFIG_MOMENCO_OCELOT_C is not set # CONFIG_MOMENCO_OCELOT_G is not set # CONFIG_MIPS_XXS1500 is not set # CONFIG_PNX8550_JBS is not set diff --git a/arch/mips/configs/malta_defconfig b/arch/mips/configs/malta_defconfig index 1c839cf..1f5cf92 100644 --- a/arch/mips/configs/malta_defconfig +++ b/arch/mips/configs/malta_defconfig @@ -35,7 +35,6 @@ CONFIG_MIPS_MALTA=y # CONFIG_MOMENCO_JAGUAR_ATX is not set # CONFIG_MOMENCO_OCELOT is not set # CONFIG_MOMENCO_OCELOT_3 is not set -# CONFIG_MOMENCO_OCELOT_C is not set # CONFIG_MOMENCO_OCELOT_G is not set # CONFIG_MIPS_XXS1500 is not set # CONFIG_PNX8550_JBS is not set diff --git a/arch/mips/configs/mipssim_defconfig b/arch/mips/configs/mipssim_defconfig index 559f4d0..ef5cae9 100644 --- a/arch/mips/configs/mipssim_defconfig +++ b/arch/mips/configs/mipssim_defconfig @@ -35,7 +35,6 @@ CONFIG_MIPS_SIM=y # CONFIG_MOMENCO_JAGUAR_ATX is not set # CONFIG_MOMENCO_OCELOT is not set # CONFIG_MOMENCO_OCELOT_3 is not set -# CONFIG_MOMENCO_OCELOT_C is not set # CONFIG_MOMENCO_OCELOT_G is not set # CONFIG_MIPS_XXS1500 is not set # CONFIG_PNX8550_JBS is not set diff --git a/arch/mips/configs/mpc30x_defconfig b/arch/mips/configs/mpc30x_defconfig index 811ada9..73a5314 100644 --- a/arch/mips/configs/mpc30x_defconfig +++ b/arch/mips/configs/mpc30x_defconfig @@ -35,7 +35,6 @@ CONFIG_ZONE_DMA=y # CONFIG_MOMENCO_JAGUAR_ATX is not set # CONFIG_MOMENCO_OCELOT is not set # CONFIG_MOMENCO_OCELOT_3 is not set -# CONFIG_MOMENCO_OCELOT_C is not set # CONFIG_MOMENCO_OCELOT_G is not set # CONFIG_MIPS_XXS1500 is not set # CONFIG_PNX8550_JBS is not set diff --git a/arch/mips/configs/ocelot_3_defconfig b/arch/mips/configs/ocelot_3_defconfig index a53175a..cc99c83 100644 --- a/arch/mips/configs/ocelot_3_defconfig +++ b/arch/mips/configs/ocelot_3_defconfig @@ -35,7 +35,6 @@ CONFIG_ZONE_DMA=y # CONFIG_MOMENCO_JAGUAR_ATX is not set # CONFIG_MOMENCO_OCELOT is not set CONFIG_MOMENCO_OCELOT_3=y -# CONFIG_MOMENCO_OCELOT_C is not set # CONFIG_MOMENCO_OCELOT_G is not set # CONFIG_MIPS_XXS1500 is not set # CONFIG_PNX8550_JBS is not set diff --git a/arch/mips/configs/ocelot_c_defconfig b/arch/mips/configs/ocelot_c_defconfig deleted file mode 100644 index 38e86f1..0000000 --- a/arch/mips/configs/ocelot_c_defconfig +++ /dev/null @@ -1,981 +0,0 @@ -# -# Automatically generated make config: don't edit -# Linux kernel version: 2.6.20 -# Tue Feb 20 21:47:36 2007 -# -CONFIG_MIPS=y - -# -# Machine selection -# -CONFIG_ZONE_DMA=y -# CONFIG_MIPS_MTX1 is not set -# CONFIG_MIPS_BOSPORUS is not set -# CONFIG_MIPS_PB1000 is not set -# CONFIG_MIPS_PB1100 is not set -# CONFIG_MIPS_PB1500 is not set -# CONFIG_MIPS_PB1550 is not set -# CONFIG_MIPS_PB1200 is not set -# CONFIG_MIPS_DB1000 is not set -# CONFIG_MIPS_DB1100 is not set -# CONFIG_MIPS_DB1500 is not set -# CONFIG_MIPS_DB1550 is not set -# CONFIG_MIPS_DB1200 is not set -# CONFIG_MIPS_MIRAGE is not set -# CONFIG_BASLER_EXCITE is not set -# CONFIG_MIPS_COBALT is not set -# CONFIG_MACH_DECSTATION is not set -# CONFIG_MACH_JAZZ is not set -# CONFIG_LASAT is not set -# CONFIG_MIPS_ATLAS is not set -# CONFIG_MIPS_MALTA is not set -# CONFIG_MIPS_SEAD is not set -# CONFIG_WR_PPMC is not set -# CONFIG_MIPS_SIM is not set -# CONFIG_MOMENCO_JAGUAR_ATX is not set -# CONFIG_MOMENCO_OCELOT is not set -# CONFIG_MOMENCO_OCELOT_3 is not set -CONFIG_MOMENCO_OCELOT_C=y -# CONFIG_MOMENCO_OCELOT_G is not set -# CONFIG_MIPS_XXS1500 is not set -# CONFIG_PNX8550_JBS is not set -# CONFIG_PNX8550_STB810 is not set -# CONFIG_DDB5477 is not set -# CONFIG_MACH_VR41XX is not set -# CONFIG_PMC_YOSEMITE is not set -# CONFIG_QEMU is not set -# CONFIG_MARKEINS is not set -# CONFIG_SGI_IP22 is not set -# CONFIG_SGI_IP27 is not set -# CONFIG_SGI_IP32 is not set -# CONFIG_SIBYTE_BIGSUR is not set -# CONFIG_SIBYTE_SWARM is not set -# CONFIG_SIBYTE_SENTOSA is not set -# CONFIG_SIBYTE_RHONE is not set -# CONFIG_SIBYTE_CARMEL is not set -# CONFIG_SIBYTE_PTSWARM is not set -# CONFIG_SIBYTE_LITTLESUR is not set -# CONFIG_SIBYTE_CRHINE is not set -# CONFIG_SIBYTE_CRHONE is not set -# CONFIG_SNI_RM is not set -# CONFIG_TOSHIBA_JMR3927 is not set -# CONFIG_TOSHIBA_RBTX4927 is not set -# CONFIG_TOSHIBA_RBTX4938 is not set -CONFIG_RWSEM_GENERIC_SPINLOCK=y -# CONFIG_ARCH_HAS_ILOG2_U32 is not set -# CONFIG_ARCH_HAS_ILOG2_U64 is not set -CONFIG_GENERIC_FIND_NEXT_BIT=y -CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y -CONFIG_GENERIC_TIME=y -CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y -CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y -CONFIG_DMA_NONCOHERENT=y -CONFIG_DMA_NEED_PCI_MAP_STATE=y -CONFIG_CPU_BIG_ENDIAN=y -# CONFIG_CPU_LITTLE_ENDIAN is not set -CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y -CONFIG_IRQ_CPU=y -CONFIG_IRQ_MV64340=y -CONFIG_PCI_MARVELL=y -CONFIG_SWAP_IO_SPACE=y -CONFIG_MIPS_L1_CACHE_SHIFT=5 - -# -# CPU selection -# -# CONFIG_CPU_MIPS32_R1 is not set -# CONFIG_CPU_MIPS32_R2 is not set -# CONFIG_CPU_MIPS64_R1 is not set -# CONFIG_CPU_MIPS64_R2 is not set -# CONFIG_CPU_R3000 is not set -# CONFIG_CPU_TX39XX is not set -# CONFIG_CPU_VR41XX is not set -# CONFIG_CPU_R4300 is not set -# CONFIG_CPU_R4X00 is not set -# CONFIG_CPU_TX49XX is not set -# CONFIG_CPU_R5000 is not set -# CONFIG_CPU_R5432 is not set -# CONFIG_CPU_R6000 is not set -# CONFIG_CPU_NEVADA is not set -# CONFIG_CPU_R8000 is not set -# CONFIG_CPU_R10000 is not set -CONFIG_CPU_RM7000=y -# CONFIG_CPU_RM9000 is not set -# CONFIG_CPU_SB1 is not set -CONFIG_SYS_HAS_CPU_RM7000=y -CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y -CONFIG_SYS_SUPPORTS_64BIT_KERNEL=y -CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y -CONFIG_CPU_SUPPORTS_64BIT_KERNEL=y - -# -# Kernel type -# -# CONFIG_32BIT is not set -CONFIG_64BIT=y -CONFIG_PAGE_SIZE_4KB=y -# CONFIG_PAGE_SIZE_8KB is not set -# CONFIG_PAGE_SIZE_16KB is not set -# CONFIG_PAGE_SIZE_64KB is not set -CONFIG_BOARD_SCACHE=y -CONFIG_RM7000_CPU_SCACHE=y -CONFIG_CPU_HAS_PREFETCH=y -CONFIG_MIPS_MT_DISABLED=y -# CONFIG_MIPS_MT_SMP is not set -# CONFIG_MIPS_MT_SMTC is not set -# CONFIG_MIPS_VPE_LOADER is not set -CONFIG_CPU_HAS_LLSC=y -CONFIG_CPU_HAS_SYNC=y -CONFIG_GENERIC_HARDIRQS=y -CONFIG_GENERIC_IRQ_PROBE=y -CONFIG_CPU_SUPPORTS_HIGHMEM=y -CONFIG_ARCH_FLATMEM_ENABLE=y -CONFIG_SELECT_MEMORY_MODEL=y -CONFIG_FLATMEM_MANUAL=y -# CONFIG_DISCONTIGMEM_MANUAL is not set -# CONFIG_SPARSEMEM_MANUAL is not set -CONFIG_FLATMEM=y -CONFIG_FLAT_NODE_MEM_MAP=y -# CONFIG_SPARSEMEM_STATIC is not set -CONFIG_SPLIT_PTLOCK_CPUS=4 -CONFIG_RESOURCES_64BIT=y -CONFIG_ZONE_DMA_FLAG=1 -# CONFIG_HZ_48 is not set -# CONFIG_HZ_100 is not set -# CONFIG_HZ_128 is not set -# CONFIG_HZ_250 is not set -# CONFIG_HZ_256 is not set -CONFIG_HZ_1000=y -# CONFIG_HZ_1024 is not set -CONFIG_SYS_SUPPORTS_ARBIT_HZ=y -CONFIG_HZ=1000 -CONFIG_PREEMPT_NONE=y -# CONFIG_PREEMPT_VOLUNTARY is not set -# CONFIG_PREEMPT is not set -# CONFIG_KEXEC is not set -CONFIG_LOCKDEP_SUPPORT=y -CONFIG_STACKTRACE_SUPPORT=y -CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" - -# -# Code maturity level options -# -CONFIG_EXPERIMENTAL=y -CONFIG_BROKEN_ON_SMP=y -CONFIG_INIT_ENV_ARG_LIMIT=32 - -# -# General setup -# -CONFIG_LOCALVERSION="" -CONFIG_LOCALVERSION_AUTO=y -CONFIG_SWAP=y -CONFIG_SYSVIPC=y -# CONFIG_IPC_NS is not set -CONFIG_SYSVIPC_SYSCTL=y -# CONFIG_POSIX_MQUEUE is not set -# CONFIG_BSD_PROCESS_ACCT is not set -# CONFIG_TASKSTATS is not set -# CONFIG_UTS_NS is not set -# CONFIG_AUDIT is not set -# CONFIG_IKCONFIG is not set -CONFIG_SYSFS_DEPRECATED=y -CONFIG_RELAY=y -# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set -CONFIG_SYSCTL=y -CONFIG_EMBEDDED=y -CONFIG_SYSCTL_SYSCALL=y -CONFIG_KALLSYMS=y -# CONFIG_KALLSYMS_EXTRA_PASS is not set -CONFIG_HOTPLUG=y -CONFIG_PRINTK=y -CONFIG_BUG=y -CONFIG_ELF_CORE=y -CONFIG_BASE_FULL=y -CONFIG_FUTEX=y -CONFIG_EPOLL=y -CONFIG_SHMEM=y -CONFIG_SLAB=y -CONFIG_VM_EVENT_COUNTERS=y -CONFIG_RT_MUTEXES=y -# CONFIG_TINY_SHMEM is not set -CONFIG_BASE_SMALL=0 -# CONFIG_SLOB is not set - -# -# Loadable module support -# -# CONFIG_MODULES is not set - -# -# Block layer -# -CONFIG_BLOCK=y -# CONFIG_BLK_DEV_IO_TRACE is not set - -# -# IO Schedulers -# -CONFIG_IOSCHED_NOOP=y -CONFIG_IOSCHED_AS=y -CONFIG_IOSCHED_DEADLINE=y -CONFIG_IOSCHED_CFQ=y -CONFIG_DEFAULT_AS=y -# CONFIG_DEFAULT_DEADLINE is not set -# CONFIG_DEFAULT_CFQ is not set -# CONFIG_DEFAULT_NOOP is not set -CONFIG_DEFAULT_IOSCHED="anticipatory" - -# -# Bus options (PCI, PCMCIA, EISA, ISA, TC) -# -CONFIG_HW_HAS_PCI=y -CONFIG_PCI=y -CONFIG_MMU=y - -# -# PCCARD (PCMCIA/CardBus) support -# -# CONFIG_PCCARD is not set - -# -# PCI Hotplug Support -# -# CONFIG_HOTPLUG_PCI is not set - -# -# Executable file formats -# -CONFIG_BINFMT_ELF=y -# CONFIG_BINFMT_MISC is not set -# CONFIG_BUILD_ELF64 is not set -CONFIG_MIPS32_COMPAT=y -CONFIG_COMPAT=y -CONFIG_SYSVIPC_COMPAT=y -CONFIG_MIPS32_O32=y -CONFIG_MIPS32_N32=y -CONFIG_BINFMT_ELF32=y - -# -# Power management options -# -CONFIG_PM=y -# CONFIG_PM_LEGACY is not set -# CONFIG_PM_DEBUG is not set -# CONFIG_PM_SYSFS_DEPRECATED is not set - -# -# Networking -# -CONFIG_NET=y - -# -# Networking options -# -# CONFIG_NETDEBUG is not set -# CONFIG_PACKET is not set -CONFIG_UNIX=y -CONFIG_XFRM=y -CONFIG_XFRM_USER=y -# CONFIG_XFRM_SUB_POLICY is not set -CONFIG_XFRM_MIGRATE=y -CONFIG_NET_KEY=y -CONFIG_NET_KEY_MIGRATE=y -CONFIG_INET=y -# CONFIG_IP_MULTICAST is not set -# CONFIG_IP_ADVANCED_ROUTER is not set -CONFIG_IP_FIB_HASH=y -CONFIG_IP_PNP=y -CONFIG_IP_PNP_DHCP=y -# CONFIG_IP_PNP_BOOTP is not set -# CONFIG_IP_PNP_RARP is not set -# CONFIG_NET_IPIP is not set -# CONFIG_NET_IPGRE is not set -# CONFIG_ARPD is not set -# CONFIG_SYN_COOKIES is not set -# CONFIG_INET_AH is not set -# CONFIG_INET_ESP is not set -# CONFIG_INET_IPCOMP is not set -# CONFIG_INET_XFRM_TUNNEL is not set -# CONFIG_INET_TUNNEL is not set -CONFIG_INET_XFRM_MODE_TRANSPORT=y -CONFIG_INET_XFRM_MODE_TUNNEL=y -CONFIG_INET_XFRM_MODE_BEET=y -CONFIG_INET_DIAG=y -CONFIG_INET_TCP_DIAG=y -# CONFIG_TCP_CONG_ADVANCED is not set -CONFIG_TCP_CONG_CUBIC=y -CONFIG_DEFAULT_TCP_CONG="cubic" -CONFIG_TCP_MD5SIG=y -# CONFIG_IPV6 is not set -# CONFIG_INET6_XFRM_TUNNEL is not set -# CONFIG_INET6_TUNNEL is not set -CONFIG_NETWORK_SECMARK=y -# CONFIG_NETFILTER is not set - -# -# DCCP Configuration (EXPERIMENTAL) -# -# CONFIG_IP_DCCP is not set - -# -# SCTP Configuration (EXPERIMENTAL) -# -# CONFIG_IP_SCTP is not set - -# -# TIPC Configuration (EXPERIMENTAL) -# -# CONFIG_TIPC is not set -# CONFIG_ATM is not set -# CONFIG_BRIDGE is not set -# CONFIG_VLAN_8021Q is not set -# CONFIG_DECNET is not set -# CONFIG_LLC2 is not set -# CONFIG_IPX is not set -# CONFIG_ATALK is not set -# CONFIG_X25 is not set -# CONFIG_LAPB is not set -# CONFIG_ECONET is not set -# CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# -# CONFIG_NET_SCHED is not set - -# -# Network testing -# -# CONFIG_NET_PKTGEN is not set -# CONFIG_HAMRADIO is not set -# CONFIG_IRDA is not set -# CONFIG_BT is not set -CONFIG_IEEE80211=y -# CONFIG_IEEE80211_DEBUG is not set -CONFIG_IEEE80211_CRYPT_WEP=y -CONFIG_IEEE80211_CRYPT_CCMP=y -CONFIG_IEEE80211_SOFTMAC=y -# CONFIG_IEEE80211_SOFTMAC_DEBUG is not set -CONFIG_WIRELESS_EXT=y - -# -# Device Drivers -# - -# -# Generic Driver Options -# -CONFIG_STANDALONE=y -CONFIG_PREVENT_FIRMWARE_BUILD=y -CONFIG_FW_LOADER=y -# CONFIG_SYS_HYPERVISOR is not set - -# -# Connector - unified userspace <-> kernelspace linker -# -CONFIG_CONNECTOR=y -CONFIG_PROC_EVENTS=y - -# -# Memory Technology Devices (MTD) -# -# CONFIG_MTD is not set - -# -# Parallel port support -# -# CONFIG_PARPORT is not set - -# -# Plug and Play support -# -# CONFIG_PNPACPI is not set - -# -# Block devices -# -# CONFIG_BLK_CPQ_DA is not set -# CONFIG_BLK_CPQ_CISS_DA is not set -# CONFIG_BLK_DEV_DAC960 is not set -# CONFIG_BLK_DEV_UMEM is not set -# CONFIG_BLK_DEV_COW_COMMON is not set -# CONFIG_BLK_DEV_LOOP is not set -# CONFIG_BLK_DEV_NBD is not set -# CONFIG_BLK_DEV_SX8 is not set -# CONFIG_BLK_DEV_RAM is not set -# CONFIG_BLK_DEV_INITRD is not set -CONFIG_CDROM_PKTCDVD=y -CONFIG_CDROM_PKTCDVD_BUFFERS=8 -# CONFIG_CDROM_PKTCDVD_WCACHE is not set -CONFIG_ATA_OVER_ETH=y - -# -# Misc devices -# -CONFIG_SGI_IOC4=y -# CONFIG_TIFM_CORE is not set - -# -# ATA/ATAPI/MFM/RLL support -# -# CONFIG_IDE is not set - -# -# SCSI device support -# -CONFIG_RAID_ATTRS=y -# CONFIG_SCSI is not set -# CONFIG_SCSI_NETLINK is not set - -# -# Serial ATA (prod) and Parallel ATA (experimental) drivers -# -# CONFIG_ATA is not set - -# -# Multi-device support (RAID and LVM) -# -# CONFIG_MD is not set - -# -# Fusion MPT device support -# -# CONFIG_FUSION is not set - -# -# IEEE 1394 (FireWire) support -# -# CONFIG_IEEE1394 is not set - -# -# I2O device support -# -# CONFIG_I2O is not set - -# -# Network device support -# -CONFIG_NETDEVICES=y -# CONFIG_DUMMY is not set -# CONFIG_BONDING is not set -# CONFIG_EQUALIZER is not set -# CONFIG_TUN is not set - -# -# ARCnet devices -# -# CONFIG_ARCNET is not set - -# -# PHY device support -# -CONFIG_PHYLIB=y - -# -# MII PHY device drivers -# -CONFIG_MARVELL_PHY=y -CONFIG_DAVICOM_PHY=y -CONFIG_QSEMI_PHY=y -CONFIG_LXT_PHY=y -CONFIG_CICADA_PHY=y -CONFIG_VITESSE_PHY=y -CONFIG_SMSC_PHY=y -# CONFIG_BROADCOM_PHY is not set -# CONFIG_FIXED_PHY is not set - -# -# Ethernet (10 or 100Mbit) -# -CONFIG_NET_ETHERNET=y -# CONFIG_MII is not set -# CONFIG_HAPPYMEAL is not set -# CONFIG_SUNGEM is not set -# CONFIG_CASSINI is not set -# CONFIG_NET_VENDOR_3COM is not set -# CONFIG_DM9000 is not set - -# -# Tulip family network device support -# -# CONFIG_NET_TULIP is not set -# CONFIG_HP100 is not set -# CONFIG_NET_PCI is not set - -# -# Ethernet (1000 Mbit) -# -# CONFIG_ACENIC is not set -# CONFIG_DL2K is not set -# CONFIG_E1000 is not set -# CONFIG_NS83820 is not set -# CONFIG_HAMACHI is not set -# CONFIG_YELLOWFIN is not set -# CONFIG_R8169 is not set -# CONFIG_SIS190 is not set -# CONFIG_SKGE is not set -# CONFIG_SKY2 is not set -# CONFIG_SK98LIN is not set -# CONFIG_TIGON3 is not set -# CONFIG_BNX2 is not set -# CONFIG_MV643XX_ETH is not set -CONFIG_QLA3XXX=y -# CONFIG_ATL1 is not set - -# -# Ethernet (10000 Mbit) -# -# CONFIG_CHELSIO_T1 is not set -CONFIG_CHELSIO_T3=y -# CONFIG_IXGB is not set -# CONFIG_S2IO is not set -# CONFIG_MYRI10GE is not set -CONFIG_NETXEN_NIC=y - -# -# Token Ring devices -# -# CONFIG_TR is not set - -# -# Wireless LAN (non-hamradio) -# -# CONFIG_NET_RADIO is not set - -# -# Wan interfaces -# -# CONFIG_WAN is not set -# CONFIG_FDDI is not set -# CONFIG_HIPPI is not set -# CONFIG_PPP is not set -# CONFIG_SLIP is not set -# CONFIG_SHAPER is not set -# CONFIG_NETCONSOLE is not set -# CONFIG_NETPOLL is not set -# CONFIG_NET_POLL_CONTROLLER is not set - -# -# ISDN subsystem -# -# CONFIG_ISDN is not set - -# -# Telephony Support -# -# CONFIG_PHONE is not set - -# -# Input device support -# -CONFIG_INPUT=y -# CONFIG_INPUT_FF_MEMLESS is not set - -# -# Userland interfaces -# -CONFIG_INPUT_MOUSEDEV=y -CONFIG_INPUT_MOUSEDEV_PSAUX=y -CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 -CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 -# CONFIG_INPUT_JOYDEV is not set -# CONFIG_INPUT_TSDEV is not set -# CONFIG_INPUT_EVDEV is not set -# CONFIG_INPUT_EVBUG is not set - -# -# Input Device Drivers -# -# CONFIG_INPUT_KEYBOARD is not set -# CONFIG_INPUT_MOUSE is not set -# CONFIG_INPUT_JOYSTICK is not set -# CONFIG_INPUT_TOUCHSCREEN is not set -# CONFIG_INPUT_MISC is not set - -# -# Hardware I/O ports -# -CONFIG_SERIO=y -# CONFIG_SERIO_I8042 is not set -CONFIG_SERIO_SERPORT=y -# CONFIG_SERIO_PCIPS2 is not set -# CONFIG_SERIO_LIBPS2 is not set -CONFIG_SERIO_RAW=y -# CONFIG_GAMEPORT is not set - -# -# Character devices -# -CONFIG_VT=y -CONFIG_VT_CONSOLE=y -CONFIG_HW_CONSOLE=y -CONFIG_VT_HW_CONSOLE_BINDING=y -# CONFIG_SERIAL_NONSTANDARD is not set - -# -# Serial drivers -# -CONFIG_SERIAL_8250=y -CONFIG_SERIAL_8250_CONSOLE=y -CONFIG_SERIAL_8250_PCI=y -CONFIG_SERIAL_8250_NR_UARTS=4 -CONFIG_SERIAL_8250_RUNTIME_UARTS=4 -# CONFIG_SERIAL_8250_EXTENDED is not set - -# -# Non-8250 serial port support -# -CONFIG_SERIAL_CORE=y -CONFIG_SERIAL_CORE_CONSOLE=y -# CONFIG_SERIAL_JSM is not set -CONFIG_UNIX98_PTYS=y -CONFIG_LEGACY_PTYS=y -CONFIG_LEGACY_PTY_COUNT=256 - -# -# IPMI -# -# CONFIG_IPMI_HANDLER is not set - -# -# Watchdog Cards -# -# CONFIG_WATCHDOG is not set -# CONFIG_HW_RANDOM is not set -# CONFIG_RTC is not set -# CONFIG_GEN_RTC is not set -# CONFIG_DTLK is not set -# CONFIG_R3964 is not set -# CONFIG_APPLICOM is not set -# CONFIG_DRM is not set -# CONFIG_RAW_DRIVER is not set - -# -# TPM devices -# -# CONFIG_TCG_TPM is not set - -# -# I2C support -# -# CONFIG_I2C is not set - -# -# SPI support -# -# CONFIG_SPI is not set -# CONFIG_SPI_MASTER is not set - -# -# Dallas's 1-wire bus -# -# CONFIG_W1 is not set - -# -# Hardware Monitoring support -# -# CONFIG_HWMON is not set -# CONFIG_HWMON_VID is not set - -# -# Multimedia devices -# -# CONFIG_VIDEO_DEV is not set - -# -# Digital Video Broadcasting Devices -# -# CONFIG_DVB is not set - -# -# Graphics support -# -# CONFIG_FIRMWARE_EDID is not set -# CONFIG_FB is not set - -# -# Console display driver support -# -# CONFIG_VGA_CONSOLE is not set -CONFIG_DUMMY_CONSOLE=y -# CONFIG_BACKLIGHT_LCD_SUPPORT is not set - -# -# Sound -# -# CONFIG_SOUND is not set - -# -# HID Devices -# -# CONFIG_HID is not set - -# -# USB support -# -CONFIG_USB_ARCH_HAS_HCD=y -CONFIG_USB_ARCH_HAS_OHCI=y -CONFIG_USB_ARCH_HAS_EHCI=y -# CONFIG_USB is not set - -# -# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' -# - -# -# USB Gadget Support -# -# CONFIG_USB_GADGET is not set - -# -# MMC/SD Card support -# -# CONFIG_MMC is not set - -# -# LED devices -# -# CONFIG_NEW_LEDS is not set - -# -# LED drivers -# - -# -# LED Triggers -# - -# -# InfiniBand support -# -# CONFIG_INFINIBAND is not set - -# -# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) -# - -# -# Real Time Clock -# -# CONFIG_RTC_CLASS is not set - -# -# DMA Engine support -# -# CONFIG_DMA_ENGINE is not set - -# -# DMA Clients -# - -# -# DMA Devices -# - -# -# Auxiliary Display support -# - -# -# Virtualization -# - -# -# File systems -# -CONFIG_EXT2_FS=y -# CONFIG_EXT2_FS_XATTR is not set -# CONFIG_EXT2_FS_XIP is not set -# CONFIG_EXT3_FS is not set -# CONFIG_EXT4DEV_FS is not set -# CONFIG_REISERFS_FS is not set -# CONFIG_JFS_FS is not set -CONFIG_FS_POSIX_ACL=y -# CONFIG_XFS_FS is not set -# CONFIG_GFS2_FS is not set -# CONFIG_OCFS2_FS is not set -# CONFIG_MINIX_FS is not set -# CONFIG_ROMFS_FS is not set -CONFIG_INOTIFY=y -CONFIG_INOTIFY_USER=y -# CONFIG_QUOTA is not set -CONFIG_DNOTIFY=y -# CONFIG_AUTOFS_FS is not set -# CONFIG_AUTOFS4_FS is not set -CONFIG_FUSE_FS=y -CONFIG_GENERIC_ACL=y - -# -# CD-ROM/DVD Filesystems -# -# CONFIG_ISO9660_FS is not set -# CONFIG_UDF_FS is not set - -# -# DOS/FAT/NT Filesystems -# -# CONFIG_MSDOS_FS is not set -# CONFIG_VFAT_FS is not set -# CONFIG_NTFS_FS is not set - -# -# Pseudo filesystems -# -CONFIG_PROC_FS=y -CONFIG_PROC_KCORE=y -CONFIG_PROC_SYSCTL=y -CONFIG_SYSFS=y -CONFIG_TMPFS=y -CONFIG_TMPFS_POSIX_ACL=y -# CONFIG_HUGETLB_PAGE is not set -CONFIG_RAMFS=y -CONFIG_CONFIGFS_FS=y - -# -# Miscellaneous filesystems -# -# CONFIG_ADFS_FS is not set -# CONFIG_AFFS_FS is not set -# CONFIG_ECRYPT_FS is not set -# CONFIG_HFS_FS is not set -# CONFIG_HFSPLUS_FS is not set -# CONFIG_BEFS_FS is not set -# CONFIG_BFS_FS is not set -# CONFIG_EFS_FS is not set -# CONFIG_CRAMFS is not set -# CONFIG_VXFS_FS is not set -# CONFIG_HPFS_FS is not set -# CONFIG_QNX4FS_FS is not set -# CONFIG_SYSV_FS is not set -# CONFIG_UFS_FS is not set - -# -# Network File Systems -# -CONFIG_NFS_FS=y -# CONFIG_NFS_V3 is not set -# CONFIG_NFS_V4 is not set -# CONFIG_NFS_DIRECTIO is not set -CONFIG_NFSD=y -# CONFIG_NFSD_V3 is not set -# CONFIG_NFSD_TCP is not set -CONFIG_ROOT_NFS=y -CONFIG_LOCKD=y -CONFIG_EXPORTFS=y -CONFIG_NFS_COMMON=y -CONFIG_SUNRPC=y -# CONFIG_RPCSEC_GSS_KRB5 is not set -# CONFIG_RPCSEC_GSS_SPKM3 is not set -# CONFIG_SMB_FS is not set -# CONFIG_CIFS is not set -# CONFIG_NCP_FS is not set -# CONFIG_CODA_FS is not set -# CONFIG_AFS_FS is not set -# CONFIG_9P_FS is not set - -# -# Partition Types -# -# CONFIG_PARTITION_ADVANCED is not set -CONFIG_MSDOS_PARTITION=y - -# -# Native Language Support -# -# CONFIG_NLS is not set - -# -# Distributed Lock Manager -# -CONFIG_DLM=y -CONFIG_DLM_TCP=y -# CONFIG_DLM_SCTP is not set -# CONFIG_DLM_DEBUG is not set - -# -# Profiling support -# -# CONFIG_PROFILING is not set - -# -# Kernel hacking -# -CONFIG_TRACE_IRQFLAGS_SUPPORT=y -# CONFIG_PRINTK_TIME is not set -CONFIG_ENABLE_MUST_CHECK=y -# CONFIG_MAGIC_SYSRQ is not set -# CONFIG_UNUSED_SYMBOLS is not set -# CONFIG_DEBUG_FS is not set -# CONFIG_HEADERS_CHECK is not set -# CONFIG_DEBUG_KERNEL is not set -CONFIG_LOG_BUF_SHIFT=14 -CONFIG_CROSSCOMPILE=y -CONFIG_CMDLINE="" - -# -# Security options -# -CONFIG_KEYS=y -CONFIG_KEYS_DEBUG_PROC_KEYS=y -# CONFIG_SECURITY is not set - -# -# Cryptographic options -# -CONFIG_CRYPTO=y -CONFIG_CRYPTO_ALGAPI=y -CONFIG_CRYPTO_BLKCIPHER=y -CONFIG_CRYPTO_HASH=y -CONFIG_CRYPTO_MANAGER=y -CONFIG_CRYPTO_HMAC=y -CONFIG_CRYPTO_XCBC=y -CONFIG_CRYPTO_NULL=y -CONFIG_CRYPTO_MD4=y -CONFIG_CRYPTO_MD5=y -CONFIG_CRYPTO_SHA1=y -CONFIG_CRYPTO_SHA256=y -CONFIG_CRYPTO_SHA512=y -CONFIG_CRYPTO_WP512=y -CONFIG_CRYPTO_TGR192=y -CONFIG_CRYPTO_GF128MUL=y -CONFIG_CRYPTO_ECB=y -CONFIG_CRYPTO_CBC=y -CONFIG_CRYPTO_PCBC=y -CONFIG_CRYPTO_LRW=y -CONFIG_CRYPTO_DES=y -CONFIG_CRYPTO_FCRYPT=y -CONFIG_CRYPTO_BLOWFISH=y -CONFIG_CRYPTO_TWOFISH=y -CONFIG_CRYPTO_TWOFISH_COMMON=y -CONFIG_CRYPTO_SERPENT=y -CONFIG_CRYPTO_AES=y -CONFIG_CRYPTO_CAST5=y -CONFIG_CRYPTO_CAST6=y -CONFIG_CRYPTO_TEA=y -CONFIG_CRYPTO_ARC4=y -CONFIG_CRYPTO_KHAZAD=y -CONFIG_CRYPTO_ANUBIS=y -CONFIG_CRYPTO_DEFLATE=y -CONFIG_CRYPTO_MICHAEL_MIC=y -CONFIG_CRYPTO_CRC32C=y -CONFIG_CRYPTO_CAMELLIA=y - -# -# Hardware crypto devices -# - -# -# Library routines -# -CONFIG_BITREVERSE=y -# CONFIG_CRC_CCITT is not set -CONFIG_CRC16=y -CONFIG_CRC32=y -CONFIG_LIBCRC32C=y -CONFIG_ZLIB_INFLATE=y -CONFIG_ZLIB_DEFLATE=y -CONFIG_PLIST=y -CONFIG_HAS_IOMEM=y -CONFIG_HAS_IOPORT=y diff --git a/arch/mips/configs/ocelot_defconfig b/arch/mips/configs/ocelot_defconfig index f5948e5..5f3b47f 100644 --- a/arch/mips/configs/ocelot_defconfig +++ b/arch/mips/configs/ocelot_defconfig @@ -35,7 +35,6 @@ CONFIG_ZONE_DMA=y # CONFIG_MOMENCO_JAGUAR_ATX is not set CONFIG_MOMENCO_OCELOT=y # CONFIG_MOMENCO_OCELOT_3 is not set -# CONFIG_MOMENCO_OCELOT_C is not set # CONFIG_MOMENCO_OCELOT_G is not set # CONFIG_MIPS_XXS1500 is not set # CONFIG_PNX8550_JBS is not set diff --git a/arch/mips/configs/pb1100_defconfig b/arch/mips/configs/pb1100_defconfig index e764285..b57662a 100644 --- a/arch/mips/configs/pb1100_defconfig +++ b/arch/mips/configs/pb1100_defconfig @@ -36,7 +36,6 @@ CONFIG_MIPS_PB1100=y # CONFIG_MOMENCO_JAGUAR_ATX is not set # CONFIG_MOMENCO_OCELOT is not set # CONFIG_MOMENCO_OCELOT_3 is not set -# CONFIG_MOMENCO_OCELOT_C is not set # CONFIG_MOMENCO_OCELOT_G is not set # CONFIG_MIPS_XXS1500 is not set # CONFIG_PNX8550_JBS is not set diff --git a/arch/mips/configs/pb1500_defconfig b/arch/mips/configs/pb1500_defconfig index 37e2a10..350f9bd 100644 --- a/arch/mips/configs/pb1500_defconfig +++ b/arch/mips/configs/pb1500_defconfig @@ -36,7 +36,6 @@ CONFIG_MIPS_PB1500=y # CONFIG_MOMENCO_JAGUAR_ATX is not set # CONFIG_MOMENCO_OCELOT is not set # CONFIG_MOMENCO_OCELOT_3 is not set -# CONFIG_MOMENCO_OCELOT_C is not set # CONFIG_MOMENCO_OCELOT_G is not set # CONFIG_MIPS_XXS1500 is not set # CONFIG_PNX8550_JBS is not set diff --git a/arch/mips/configs/pb1550_defconfig b/arch/mips/configs/pb1550_defconfig index b1206a2..8ea039a 100644 --- a/arch/mips/configs/pb1550_defconfig +++ b/arch/mips/configs/pb1550_defconfig @@ -36,7 +36,6 @@ CONFIG_MIPS_PB1550=y # CONFIG_MOMENCO_JAGUAR_ATX is not set # CONFIG_MOMENCO_OCELOT is not set # CONFIG_MOMENCO_OCELOT_3 is not set -# CONFIG_MOMENCO_OCELOT_C is not set # CONFIG_MOMENCO_OCELOT_G is not set # CONFIG_MIPS_XXS1500 is not set # CONFIG_PNX8550_JBS is not set diff --git a/arch/mips/configs/pnx8550-jbs_defconfig b/arch/mips/configs/pnx8550-jbs_defconfig index e709644..9c8c54e 100644 --- a/arch/mips/configs/pnx8550-jbs_defconfig +++ b/arch/mips/configs/pnx8550-jbs_defconfig @@ -35,7 +35,6 @@ CONFIG_ZONE_DMA=y # CONFIG_MOMENCO_JAGUAR_ATX is not set # CONFIG_MOMENCO_OCELOT is not set # CONFIG_MOMENCO_OCELOT_3 is not set -# CONFIG_MOMENCO_OCELOT_C is not set # CONFIG_MOMENCO_OCELOT_G is not set # CONFIG_MIPS_XXS1500 is not set CONFIG_PNX8550_JBS=y diff --git a/arch/mips/configs/pnx8550-stb810_defconfig b/arch/mips/configs/pnx8550-stb810_defconfig index a46761f..2f60c5a 100644 --- a/arch/mips/configs/pnx8550-stb810_defconfig +++ b/arch/mips/configs/pnx8550-stb810_defconfig @@ -35,7 +35,6 @@ CONFIG_ZONE_DMA=y # CONFIG_MOMENCO_JAGUAR_ATX is not set # CONFIG_MOMENCO_OCELOT is not set # CONFIG_MOMENCO_OCELOT_3 is not set -# CONFIG_MOMENCO_OCELOT_C is not set # CONFIG_MOMENCO_OCELOT_G is not set # CONFIG_MIPS_XXS1500 is not set # CONFIG_PNX8550_JBS is not set diff --git a/arch/mips/configs/qemu_defconfig b/arch/mips/configs/qemu_defconfig index 93f382b..d7ace08 100644 --- a/arch/mips/configs/qemu_defconfig +++ b/arch/mips/configs/qemu_defconfig @@ -35,7 +35,6 @@ CONFIG_ZONE_DMA=y # CONFIG_MOMENCO_JAGUAR_ATX is not set # CONFIG_MOMENCO_OCELOT is not set # CONFIG_MOMENCO_OCELOT_3 is not set -# CONFIG_MOMENCO_OCELOT_C is not set # CONFIG_MOMENCO_OCELOT_G is not set # CONFIG_MIPS_XXS1500 is not set # CONFIG_PNX8550_JBS is not set diff --git a/arch/mips/configs/rbhma4200_defconfig b/arch/mips/configs/rbhma4200_defconfig index dbb485d..b020e92 100644 --- a/arch/mips/configs/rbhma4200_defconfig +++ b/arch/mips/configs/rbhma4200_defconfig @@ -33,7 +33,6 @@ CONFIG_MIPS=y # CONFIG_MIPS_SIM is not set # CONFIG_MOMENCO_OCELOT is not set # CONFIG_MOMENCO_OCELOT_3 is not set -# CONFIG_MOMENCO_OCELOT_C is not set # CONFIG_MIPS_XXS1500 is not set # CONFIG_PNX8550_JBS is not set # CONFIG_PNX8550_STB810 is not set diff --git a/arch/mips/configs/rbhma4500_defconfig b/arch/mips/configs/rbhma4500_defconfig index c7c28a1..b0abd16 100644 --- a/arch/mips/configs/rbhma4500_defconfig +++ b/arch/mips/configs/rbhma4500_defconfig @@ -35,7 +35,6 @@ CONFIG_ZONE_DMA=y # CONFIG_MOMENCO_JAGUAR_ATX is not set # CONFIG_MOMENCO_OCELOT is not set # CONFIG_MOMENCO_OCELOT_3 is not set -# CONFIG_MOMENCO_OCELOT_C is not set # CONFIG_MOMENCO_OCELOT_G is not set # CONFIG_MIPS_XXS1500 is not set # CONFIG_PNX8550_JBS is not set diff --git a/arch/mips/configs/rm200_defconfig b/arch/mips/configs/rm200_defconfig index f3ee7e17..120dcff 100644 --- a/arch/mips/configs/rm200_defconfig +++ b/arch/mips/configs/rm200_defconfig @@ -35,7 +35,6 @@ CONFIG_ZONE_DMA=y # CONFIG_MOMENCO_JAGUAR_ATX is not set # CONFIG_MOMENCO_OCELOT is not set # CONFIG_MOMENCO_OCELOT_3 is not set -# CONFIG_MOMENCO_OCELOT_C is not set # CONFIG_MOMENCO_OCELOT_G is not set # CONFIG_MIPS_XXS1500 is not set # CONFIG_PNX8550_JBS is not set diff --git a/arch/mips/configs/sb1250-swarm_defconfig b/arch/mips/configs/sb1250-swarm_defconfig index 11f0347..534de60 100644 --- a/arch/mips/configs/sb1250-swarm_defconfig +++ b/arch/mips/configs/sb1250-swarm_defconfig @@ -35,7 +35,6 @@ CONFIG_ZONE_DMA=y # CONFIG_MOMENCO_JAGUAR_ATX is not set # CONFIG_MOMENCO_OCELOT is not set # CONFIG_MOMENCO_OCELOT_3 is not set -# CONFIG_MOMENCO_OCELOT_C is not set # CONFIG_MOMENCO_OCELOT_G is not set # CONFIG_MIPS_XXS1500 is not set # CONFIG_PNX8550_JBS is not set diff --git a/arch/mips/configs/sead_defconfig b/arch/mips/configs/sead_defconfig index 0d055b2..e0185eb 100644 --- a/arch/mips/configs/sead_defconfig +++ b/arch/mips/configs/sead_defconfig @@ -35,7 +35,6 @@ CONFIG_MIPS_SEAD=y # CONFIG_MOMENCO_JAGUAR_ATX is not set # CONFIG_MOMENCO_OCELOT is not set # CONFIG_MOMENCO_OCELOT_3 is not set -# CONFIG_MOMENCO_OCELOT_C is not set # CONFIG_MOMENCO_OCELOT_G is not set # CONFIG_MIPS_XXS1500 is not set # CONFIG_PNX8550_JBS is not set diff --git a/arch/mips/configs/tb0219_defconfig b/arch/mips/configs/tb0219_defconfig index a0cda22..11f4c66 100644 --- a/arch/mips/configs/tb0219_defconfig +++ b/arch/mips/configs/tb0219_defconfig @@ -35,7 +35,6 @@ CONFIG_ZONE_DMA=y # CONFIG_MOMENCO_JAGUAR_ATX is not set # CONFIG_MOMENCO_OCELOT is not set # CONFIG_MOMENCO_OCELOT_3 is not set -# CONFIG_MOMENCO_OCELOT_C is not set # CONFIG_MOMENCO_OCELOT_G is not set # CONFIG_MIPS_XXS1500 is not set # CONFIG_PNX8550_JBS is not set diff --git a/arch/mips/configs/tb0226_defconfig b/arch/mips/configs/tb0226_defconfig index 9b0a1d5..1c54d1b 100644 --- a/arch/mips/configs/tb0226_defconfig +++ b/arch/mips/configs/tb0226_defconfig @@ -35,7 +35,6 @@ CONFIG_ZONE_DMA=y # CONFIG_MOMENCO_JAGUAR_ATX is not set # CONFIG_MOMENCO_OCELOT is not set # CONFIG_MOMENCO_OCELOT_3 is not set -# CONFIG_MOMENCO_OCELOT_C is not set # CONFIG_MOMENCO_OCELOT_G is not set # CONFIG_MIPS_XXS1500 is not set # CONFIG_PNX8550_JBS is not set diff --git a/arch/mips/configs/tb0287_defconfig b/arch/mips/configs/tb0287_defconfig index f8f11dc..7f2ece3 100644 --- a/arch/mips/configs/tb0287_defconfig +++ b/arch/mips/configs/tb0287_defconfig @@ -35,7 +35,6 @@ CONFIG_ZONE_DMA=y # CONFIG_MOMENCO_JAGUAR_ATX is not set # CONFIG_MOMENCO_OCELOT is not set # CONFIG_MOMENCO_OCELOT_3 is not set -# CONFIG_MOMENCO_OCELOT_C is not set # CONFIG_MOMENCO_OCELOT_G is not set # CONFIG_MIPS_XXS1500 is not set # CONFIG_PNX8550_JBS is not set diff --git a/arch/mips/configs/workpad_defconfig b/arch/mips/configs/workpad_defconfig index 8558348..ef66330 100644 --- a/arch/mips/configs/workpad_defconfig +++ b/arch/mips/configs/workpad_defconfig @@ -35,7 +35,6 @@ CONFIG_ZONE_DMA=y # CONFIG_MOMENCO_JAGUAR_ATX is not set # CONFIG_MOMENCO_OCELOT is not set # CONFIG_MOMENCO_OCELOT_3 is not set -# CONFIG_MOMENCO_OCELOT_C is not set # CONFIG_MOMENCO_OCELOT_G is not set # CONFIG_MIPS_XXS1500 is not set # CONFIG_PNX8550_JBS is not set diff --git a/arch/mips/configs/wrppmc_defconfig b/arch/mips/configs/wrppmc_defconfig index 01b05b2..d57d6cc 100644 --- a/arch/mips/configs/wrppmc_defconfig +++ b/arch/mips/configs/wrppmc_defconfig @@ -35,7 +35,6 @@ CONFIG_WR_PPMC=y # CONFIG_MOMENCO_JAGUAR_ATX is not set # CONFIG_MOMENCO_OCELOT is not set # CONFIG_MOMENCO_OCELOT_3 is not set -# CONFIG_MOMENCO_OCELOT_C is not set # CONFIG_MOMENCO_OCELOT_G is not set # CONFIG_MIPS_XXS1500 is not set # CONFIG_PNX8550_JBS is not set diff --git a/arch/mips/configs/yosemite_defconfig b/arch/mips/configs/yosemite_defconfig index 3d40e7c..3834921 100644 --- a/arch/mips/configs/yosemite_defconfig +++ b/arch/mips/configs/yosemite_defconfig @@ -35,7 +35,6 @@ CONFIG_ZONE_DMA=y # CONFIG_MOMENCO_JAGUAR_ATX is not set # CONFIG_MOMENCO_OCELOT is not set # CONFIG_MOMENCO_OCELOT_3 is not set -# CONFIG_MOMENCO_OCELOT_C is not set # CONFIG_MOMENCO_OCELOT_G is not set # CONFIG_MIPS_XXS1500 is not set # CONFIG_PNX8550_JBS is not set diff --git a/arch/mips/defconfig b/arch/mips/defconfig index 195311d..9515ed6 100644 --- a/arch/mips/defconfig +++ b/arch/mips/defconfig @@ -35,7 +35,6 @@ CONFIG_ZONE_DMA=y # CONFIG_MOMENCO_JAGUAR_ATX is not set # CONFIG_MOMENCO_OCELOT is not set # CONFIG_MOMENCO_OCELOT_3 is not set -# CONFIG_MOMENCO_OCELOT_C is not set # CONFIG_MOMENCO_OCELOT_G is not set # CONFIG_MIPS_XXS1500 is not set # CONFIG_PNX8550_JBS is not set diff --git a/arch/mips/momentum/ocelot_c/Makefile b/arch/mips/momentum/ocelot_c/Makefile deleted file mode 100644 index d69161a..0000000 --- a/arch/mips/momentum/ocelot_c/Makefile +++ /dev/null @@ -1,8 +0,0 @@ -# -# Makefile for Momentum Computer's Ocelot-C and -CS boards. -# - -obj-y += cpci-irq.o irq.o platform.o prom.o reset.o \ - setup.o uart-irq.o - -obj-$(CONFIG_KGDB) += dbg_io.o diff --git a/arch/mips/momentum/ocelot_c/cpci-irq.c b/arch/mips/momentum/ocelot_c/cpci-irq.c deleted file mode 100644 index 186a140..0000000 --- a/arch/mips/momentum/ocelot_c/cpci-irq.c +++ /dev/null @@ -1,100 +0,0 @@ -/* - * Copyright 2002 Momentum Computer - * Author: mdharm@momenco.com - * - * arch/mips/momentum/ocelot_c/cpci-irq.c - * Interrupt routines for cpci. Interrupt numbers are assigned from - * CPCI_IRQ_BASE to CPCI_IRQ_BASE+8 (8 interrupt sources). - * - * Note that the high-level software will need to be careful about using - * these interrupts. If this board is asserting a cPCI interrupt, it will - * also see the asserted interrupt. Care must be taken to avoid an - * interrupt flood. - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - */ - -#include <linux/module.h> -#include <linux/interrupt.h> -#include <linux/irq.h> -#include <linux/kernel.h> -#include <linux/sched.h> -#include <linux/kernel_stat.h> -#include <asm/io.h> -#include "ocelot_c_fpga.h" - -#define CPCI_IRQ_BASE 8 - -static inline int ls1bit8(unsigned int x) -{ - int b = 7, s; - - s = 4; if (((unsigned char)(x << 4)) == 0) s = 0; b -= s; x <<= s; - s = 2; if (((unsigned char)(x << 2)) == 0) s = 0; b -= s; x <<= s; - s = 1; if (((unsigned char)(x << 1)) == 0) s = 0; b -= s; - - return b; -} - -/* mask off an interrupt -- 0 is enable, 1 is disable */ -static inline void mask_cpci_irq(unsigned int irq) -{ - uint32_t value; - - value = OCELOT_FPGA_READ(INTMASK); - value |= 1 << (irq - CPCI_IRQ_BASE); - OCELOT_FPGA_WRITE(value, INTMASK); - - /* read the value back to assure that it's really been written */ - value = OCELOT_FPGA_READ(INTMASK); -} - -/* unmask an interrupt -- 0 is enable, 1 is disable */ -static inline void unmask_cpci_irq(unsigned int irq) -{ - uint32_t value; - - value = OCELOT_FPGA_READ(INTMASK); - value &= ~(1 << (irq - CPCI_IRQ_BASE)); - OCELOT_FPGA_WRITE(value, INTMASK); - - /* read the value back to assure that it's really been written */ - value = OCELOT_FPGA_READ(INTMASK); -} - -/* - * Interrupt handler for interrupts coming from the FPGA chip. - * It could be built in ethernet ports etc... - */ -void ll_cpci_irq(void) -{ - unsigned int irq_src, irq_mask; - - /* read the interrupt status registers */ - irq_src = OCELOT_FPGA_READ(INTSTAT); - irq_mask = OCELOT_FPGA_READ(INTMASK); - - /* mask for just the interrupts we want */ - irq_src &= ~irq_mask; - - do_IRQ(ls1bit8(irq_src) + CPCI_IRQ_BASE); -} - -struct irq_chip cpci_irq_type = { - .name = "CPCI/FPGA", - .ack = mask_cpci_irq, - .mask = mask_cpci_irq, - .mask_ack = mask_cpci_irq, - .unmask = unmask_cpci_irq, -}; - -void cpci_irq_init(void) -{ - int i; - - for (i = CPCI_IRQ_BASE; i < (CPCI_IRQ_BASE + 8); i++) - set_irq_chip_and_handler(i, &cpci_irq_type, handle_level_irq); -} diff --git a/arch/mips/momentum/ocelot_c/dbg_io.c b/arch/mips/momentum/ocelot_c/dbg_io.c deleted file mode 100644 index 32d6fb4..0000000 --- a/arch/mips/momentum/ocelot_c/dbg_io.c +++ /dev/null @@ -1,121 +0,0 @@ - -#include <asm/serial.h> /* For the serial port location and base baud */ - -/* --- CONFIG --- */ - -typedef unsigned char uint8; -typedef unsigned int uint32; - -/* --- END OF CONFIG --- */ - -#define UART16550_BAUD_2400 2400 -#define UART16550_BAUD_4800 4800 -#define UART16550_BAUD_9600 9600 -#define UART16550_BAUD_19200 19200 -#define UART16550_BAUD_38400 38400 -#define UART16550_BAUD_57600 57600 -#define UART16550_BAUD_115200 115200 - -#define UART16550_PARITY_NONE 0 -#define UART16550_PARITY_ODD 0x08 -#define UART16550_PARITY_EVEN 0x18 -#define UART16550_PARITY_MARK 0x28 -#define UART16550_PARITY_SPACE 0x38 - -#define UART16550_DATA_5BIT 0x0 -#define UART16550_DATA_6BIT 0x1 -#define UART16550_DATA_7BIT 0x2 -#define UART16550_DATA_8BIT 0x3 - -#define UART16550_STOP_1BIT 0x0 -#define UART16550_STOP_2BIT 0x4 - -/* ----------------------------------------------------- */ - -/* === CONFIG === */ - -/* [jsun] we use the second serial port for kdb */ -#define BASE OCELOT_SERIAL1_BASE -#define MAX_BAUD OCELOT_BASE_BAUD - -/* === END OF CONFIG === */ - -#define REG_OFFSET 4 - -/* register offset */ -#define OFS_RCV_BUFFER 0 -#define OFS_TRANS_HOLD 0 -#define OFS_SEND_BUFFER 0 -#define OFS_INTR_ENABLE (1*REG_OFFSET) -#define OFS_INTR_ID (2*REG_OFFSET) -#define OFS_DATA_FORMAT (3*REG_OFFSET) -#define OFS_LINE_CONTROL (3*REG_OFFSET) -#define OFS_MODEM_CONTROL (4*REG_OFFSET) -#define OFS_RS232_OUTPUT (4*REG_OFFSET) -#define OFS_LINE_STATUS (5*REG_OFFSET) -#define OFS_MODEM_STATUS (6*REG_OFFSET) -#define OFS_RS232_INPUT (6*REG_OFFSET) -#define OFS_SCRATCH_PAD (7*REG_OFFSET) - -#define OFS_DIVISOR_LSB (0*REG_OFFSET) -#define OFS_DIVISOR_MSB (1*REG_OFFSET) - - -/* memory-mapped read/write of the port */ -#define UART16550_READ(y) (*((volatile uint8*)(BASE + y))) -#define UART16550_WRITE(y, z) ((*((volatile uint8*)(BASE + y))) = z) - -void debugInit(uint32 baud, uint8 data, uint8 parity, uint8 stop) -{ - /* disable interrupts */ - UART16550_WRITE(OFS_INTR_ENABLE, 0); - - /* set up baud rate */ - { - uint32 divisor; - - /* set DIAB bit */ - UART16550_WRITE(OFS_LINE_CONTROL, 0x80); - - /* set divisor */ - divisor = MAX_BAUD / baud; - UART16550_WRITE(OFS_DIVISOR_LSB, divisor & 0xff); - UART16550_WRITE(OFS_DIVISOR_MSB, (divisor & 0xff00) >> 8); - - /* clear DIAB bit */ - UART16550_WRITE(OFS_LINE_CONTROL, 0x0); - } - - /* set data format */ - UART16550_WRITE(OFS_DATA_FORMAT, data | parity | stop); -} - -static int remoteDebugInitialized = 0; - -uint8 getDebugChar(void) -{ - if (!remoteDebugInitialized) { - remoteDebugInitialized = 1; - debugInit(UART16550_BAUD_38400, - UART16550_DATA_8BIT, - UART16550_PARITY_NONE, UART16550_STOP_1BIT); - } - - while ((UART16550_READ(OFS_LINE_STATUS) & 0x1) == 0); - return UART16550_READ(OFS_RCV_BUFFER); -} - - -int putDebugChar(uint8 byte) -{ - if (!remoteDebugInitialized) { - remoteDebugInitialized = 1; - debugInit(UART16550_BAUD_38400, - UART16550_DATA_8BIT, - UART16550_PARITY_NONE, UART16550_STOP_1BIT); - } - - while ((UART16550_READ(OFS_LINE_STATUS) & 0x20) == 0); - UART16550_WRITE(OFS_SEND_BUFFER, byte); - return 1; -} diff --git a/arch/mips/momentum/ocelot_c/irq.c b/arch/mips/momentum/ocelot_c/irq.c deleted file mode 100644 index 844d566..0000000 --- a/arch/mips/momentum/ocelot_c/irq.c +++ /dev/null @@ -1,107 +0,0 @@ -/* - * Copyright (C) 2000 RidgeRun, Inc. - * Author: RidgeRun, Inc. - * glonnon@ridgerun.com, skranz@ridgerun.com, stevej@ridgerun.com - * - * Copyright 2001 MontaVista Software Inc. - * Author: Jun Sun, jsun@mvista.com or jsun@junsun.net - * Copyright (C) 2000, 01, 05 Ralf Baechle (ralf@linux-mips.org) - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - * - * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED - * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF - * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN - * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, - * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT - * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF - * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON - * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT - * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF - * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - * You should have received a copy of the GNU General Public License along - * with this program; if not, write to the Free Software Foundation, Inc., - * 675 Mass Ave, Cambridge, MA 02139, USA. - * - */ -#include <linux/errno.h> -#include <linux/init.h> -#include <linux/kernel_stat.h> -#include <linux/module.h> -#include <linux/signal.h> -#include <linux/sched.h> -#include <linux/types.h> -#include <linux/interrupt.h> -#include <linux/ioport.h> -#include <linux/timex.h> -#include <linux/slab.h> -#include <linux/random.h> -#include <linux/bitops.h> -#include <linux/mv643xx.h> -#include <asm/bootinfo.h> -#include <asm/io.h> -#include <asm/irq_cpu.h> -#include <asm/mipsregs.h> -#include <asm/system.h> - -extern void uart_irq_init(void); -extern void cpci_irq_init(void); - -static struct irqaction cascade_fpga = { - no_action, IRQF_DISABLED, CPU_MASK_NONE, "cascade via FPGA", NULL, NULL -}; - -static struct irqaction cascade_mv64340 = { - no_action, IRQF_DISABLED, CPU_MASK_NONE, "cascade via MV64340", NULL, NULL -}; - -extern void ll_uart_irq(void); -extern void ll_cpci_irq(void); - -asmlinkage void plat_irq_dispatch(void) -{ - unsigned int pending = read_c0_cause() & read_c0_status() & ST0_IM; - - if (pending & STATUSF_IP0) - do_IRQ(0); - else if (pending & STATUSF_IP1) - do_IRQ(1); - else if (pending & STATUSF_IP2) - do_IRQ(2); - else if (pending & STATUSF_IP3) - ll_uart_irq(); - else if (pending & STATUSF_IP4) - do_IRQ(4); - else if (pending & STATUSF_IP5) - ll_cpci_irq(); - else if (pending & STATUSF_IP6) - ll_mv64340_irq(); - else if (pending & STATUSF_IP7) - do_IRQ(7); - else - spurious_interrupt(); -} - -void __init arch_init_irq(void) -{ - /* - * Clear all of the interrupts while we change the able around a bit. - * int-handler is not on bootstrap - */ - clear_c0_status(ST0_IM); - - mips_cpu_irq_init(); - - /* set up the cascading interrupts */ - setup_irq(3, &cascade_fpga); - setup_irq(5, &cascade_fpga); - setup_irq(6, &cascade_mv64340); - - mv64340_irq_init(16); - uart_irq_init(); - cpci_irq_init(); -} diff --git a/arch/mips/momentum/ocelot_c/ocelot_c_fpga.h b/arch/mips/momentum/ocelot_c/ocelot_c_fpga.h deleted file mode 100644 index f0f5581..0000000 --- a/arch/mips/momentum/ocelot_c/ocelot_c_fpga.h +++ /dev/null @@ -1,61 +0,0 @@ -/* - * Ocelot-C Board Register Definitions - * - * (C) 2002 Momentum Computer Inc. - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - * - * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED - * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF - * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN - * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, - * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT - * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF - * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON - * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT - * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF - * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - * You should have received a copy of the GNU General Public License along - * with this program; if not, write to the Free Software Foundation, Inc., - * 675 Mass Ave, Cambridge, MA 02139, USA. - * - * Louis Hamilton, Red Hat, Inc. - * hamilton@redhat.com [MIPS64 modifications] - */ - -#ifndef __OCELOT_C_FPGA_H__ -#define __OCELOT_C_FPGA_H__ - - -#ifdef CONFIG_64BIT -#define OCELOT_C_CS0_ADDR (0xfffffffffc000000) -#else -#define OCELOT_C_CS0_ADDR (0xfc000000) -#endif - -#define OCELOT_C_REG_BOARDREV 0x0 -#define OCELOT_C_REG_FPGA_REV 0x1 -#define OCELOT_C_REG_FPGA_TYPE 0x2 -#define OCELOT_C_REG_RESET_STATUS 0x3 -#define OCELOT_C_REG_BOARD_STATUS 0x4 -#define OCELOT_C_REG_CPCI_ID 0x5 -#define OCELOT_C_REG_SET 0x6 -#define OCELOT_C_REG_CLR 0x7 -#define OCELOT_C_REG_EEPROM_MODE 0x9 -#define OCELOT_C_REG_INTMASK 0xa -#define OCELOT_C_REG_INTSTAT 0xb -#define OCELOT_C_REG_UART_INTMASK 0xc -#define OCELOT_C_REG_UART_INTSTAT 0xd -#define OCELOT_C_REG_INTSET 0xe -#define OCELOT_C_REG_INTCLR 0xf - -#define __FPGA_REG_TO_ADDR(reg) \ - ((void *) OCELOT_C_CS0_ADDR + OCELOT_C_REG_##reg) -#define OCELOT_FPGA_WRITE(x, reg) writeb(x, __FPGA_REG_TO_ADDR(reg)) -#define OCELOT_FPGA_READ(reg) readb(__FPGA_REG_TO_ADDR(reg)) - -#endif diff --git a/arch/mips/momentum/ocelot_c/platform.c b/arch/mips/momentum/ocelot_c/platform.c deleted file mode 100644 index 7780aa0..0000000 --- a/arch/mips/momentum/ocelot_c/platform.c +++ /dev/null @@ -1,183 +0,0 @@ -#include <linux/delay.h> -#include <linux/if_ether.h> -#include <linux/ioport.h> -#include <linux/mv643xx.h> -#include <linux/platform_device.h> - -#include "ocelot_c_fpga.h" - -#if defined(CONFIG_MV643XX_ETH) || defined(CONFIG_MV643XX_ETH_MODULE) - -static struct resource mv643xx_eth_shared_resources[] = { - [0] = { - .name = "ethernet shared base", - .start = 0xf1000000 + MV643XX_ETH_SHARED_REGS, - .end = 0xf1000000 + MV643XX_ETH_SHARED_REGS + - MV643XX_ETH_SHARED_REGS_SIZE - 1, - .flags = IORESOURCE_MEM, - }, -}; - -static struct platform_device mv643xx_eth_shared_device = { - .name = MV643XX_ETH_SHARED_NAME, - .id = 0, - .num_resources = ARRAY_SIZE(mv643xx_eth_shared_resources), - .resource = mv643xx_eth_shared_resources, -}; - -#define MV_SRAM_BASE 0xfe000000UL -#define MV_SRAM_SIZE (256 * 1024) - -#define MV_SRAM_RXRING_SIZE (MV_SRAM_SIZE / 4) -#define MV_SRAM_TXRING_SIZE (MV_SRAM_SIZE / 4) - -#define MV_SRAM_BASE_ETH0 MV_SRAM_BASE -#define MV_SRAM_BASE_ETH1 (MV_SRAM_BASE + (MV_SRAM_SIZE / 2)) - -#define MV64x60_IRQ_ETH_0 48 -#define MV64x60_IRQ_ETH_1 49 - -static struct resource mv64x60_eth0_resources[] = { - [0] = { - .name = "eth0 irq", - .start = MV64x60_IRQ_ETH_0, - .end = MV64x60_IRQ_ETH_0, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct mv643xx_eth_platform_data eth0_pd = { - .port_number = 0, - - .tx_sram_addr = MV_SRAM_BASE_ETH0, - .tx_sram_size = MV_SRAM_TXRING_SIZE, - .tx_queue_size = MV_SRAM_TXRING_SIZE / 16, - - .rx_sram_addr = MV_SRAM_BASE_ETH0 + MV_SRAM_TXRING_SIZE, - .rx_sram_size = MV_SRAM_RXRING_SIZE, - .rx_queue_size = MV_SRAM_RXRING_SIZE / 16, -}; - -static struct platform_device eth0_device = { - .name = MV643XX_ETH_NAME, - .id = 0, - .num_resources = ARRAY_SIZE(mv64x60_eth0_resources), - .resource = mv64x60_eth0_resources, - .dev = { - .platform_data = ð0_pd, - }, -}; - -static struct resource mv64x60_eth1_resources[] = { - [0] = { - .name = "eth1 irq", - .start = MV64x60_IRQ_ETH_1, - .end = MV64x60_IRQ_ETH_1, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct mv643xx_eth_platform_data eth1_pd = { - .port_number = 1, - - .tx_sram_addr = MV_SRAM_BASE_ETH1, - .tx_sram_size = MV_SRAM_TXRING_SIZE, - .tx_queue_size = MV_SRAM_TXRING_SIZE / 16, - - .rx_sram_addr = MV_SRAM_BASE_ETH1 + MV_SRAM_TXRING_SIZE, - .rx_sram_size = MV_SRAM_RXRING_SIZE, - .rx_queue_size = MV_SRAM_RXRING_SIZE / 16, -}; - -static struct platform_device eth1_device = { - .name = MV643XX_ETH_NAME, - .id = 1, - .num_resources = ARRAY_SIZE(mv64x60_eth1_resources), - .resource = mv64x60_eth1_resources, - .dev = { - .platform_data = ð1_pd, - }, -}; - -static struct platform_device *mv643xx_eth_pd_devs[] __initdata = { - &mv643xx_eth_shared_device, - ð0_device, - ð1_device, - /* The third port is not wired up on the Ocelot C */ -}; - -static u8 __init exchange_bit(u8 val, u8 cs) -{ - /* place the data */ - OCELOT_FPGA_WRITE((val << 2) | cs, EEPROM_MODE); - udelay(1); - - /* turn the clock on */ - OCELOT_FPGA_WRITE((val << 2) | cs | 0x2, EEPROM_MODE); - udelay(1); - - /* turn the clock off and read-strobe */ - OCELOT_FPGA_WRITE((val << 2) | cs | 0x10, EEPROM_MODE); - - /* return the data */ - return (OCELOT_FPGA_READ(EEPROM_MODE) >> 3) & 0x1; -} - -static void __init get_mac(char dest[6]) -{ - u8 read_opcode[12] = {1, 1, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0}; - int i,j; - - for (i = 0; i < 12; i++) - exchange_bit(read_opcode[i], 1); - - for (j = 0; j < 6; j++) { - dest[j] = 0; - for (i = 0; i < 8; i++) { - dest[j] <<= 1; - dest[j] |= exchange_bit(0, 1); - } - } - - /* turn off CS */ - exchange_bit(0,0); -} - -/* - * Copy and increment ethernet MAC address by a small value. - * - * This is useful for systems where the only one MAC address is stored in - * non-volatile memory for multiple ports. - */ -static inline void eth_mac_add(unsigned char *dst, unsigned char *src, - unsigned int add) -{ - int i; - - BUG_ON(add >= 256); - - for (i = ETH_ALEN; i >= 0; i--) { - dst[i] = src[i] + add; - add = dst[i] < src[i]; /* compute carry */ - } - - WARN_ON(add); -} - -static int __init mv643xx_eth_add_pds(void) -{ - unsigned char mac[ETH_ALEN]; - int ret; - - get_mac(mac); - eth_mac_add(eth0_pd.mac_addr, mac, 0); - eth_mac_add(eth1_pd.mac_addr, mac, 1); - ret = platform_add_devices(mv643xx_eth_pd_devs, - ARRAY_SIZE(mv643xx_eth_pd_devs)); - - return ret; -} - -device_initcall(mv643xx_eth_add_pds); - -#endif /* defined(CONFIG_MV643XX_ETH) || defined(CONFIG_MV643XX_ETH_MODULE) */ diff --git a/arch/mips/momentum/ocelot_c/prom.c b/arch/mips/momentum/ocelot_c/prom.c deleted file mode 100644 index b689cee..0000000 --- a/arch/mips/momentum/ocelot_c/prom.c +++ /dev/null @@ -1,183 +0,0 @@ -/* - * Copyright 2002 Momentum Computer Inc. - * Author: Matthew Dharm <mdharm@momenco.com> - * - * Louis Hamilton, Red Hat, Inc. - * hamilton@redhat.com [MIPS64 modifications] - * - * Based on Ocelot Linux port, which is - * Copyright 2001 MontaVista Software Inc. - * Author: jsun@mvista.com or jsun@junsun.net - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - */ -#include <linux/init.h> -#include <linux/mm.h> -#include <linux/sched.h> -#include <linux/bootmem.h> -#include <linux/mv643xx.h> - -#include <asm/addrspace.h> -#include <asm/bootinfo.h> -#include <asm/pmon.h> - -#include "ocelot_c_fpga.h" - -struct callvectors* debug_vectors; - -extern unsigned long marvell_base; -extern unsigned int cpu_clock; - -const char *get_system_type(void) -{ -#ifdef CONFIG_CPU_SR71000 - return "Momentum Ocelot-CS"; -#else - return "Momentum Ocelot-C"; -#endif -} - -#ifdef CONFIG_64BIT - -unsigned long signext(unsigned long addr) -{ - addr &= 0xffffffff; - return (unsigned long)((int)addr); -} - -void *get_arg(unsigned long args, int arc) -{ - unsigned long ul; - unsigned char *puc, uc; - - args += (arc * 4); - ul = (unsigned long)signext(args); - puc = (unsigned char *)ul; - if (puc == 0) - return (void *)0; - -#ifdef CONFIG_CPU_LITTLE_ENDIAN - uc = *puc++; - ul = (unsigned long)uc; - uc = *puc++; - ul |= (((unsigned long)uc) << 8); - uc = *puc++; - ul |= (((unsigned long)uc) << 16); - uc = *puc++; - ul |= (((unsigned long)uc) << 24); -#else /* CONFIG_CPU_LITTLE_ENDIAN */ - uc = *puc++; - ul = ((unsigned long)uc) << 24; - uc = *puc++; - ul |= (((unsigned long)uc) << 16); - uc = *puc++; - ul |= (((unsigned long)uc) << 8); - uc = *puc++; - ul |= ((unsigned long)uc); -#endif /* CONFIG_CPU_LITTLE_ENDIAN */ - ul = signext(ul); - return (void *)ul; -} - -char *arg64(unsigned long addrin, int arg_index) -{ - unsigned long args; - char *p; - args = signext(addrin); - p = (char *)get_arg(args, arg_index); - return p; -} -#endif /* CONFIG_64BIT */ - - -void __init prom_init(void) -{ - int argc = fw_arg0; - char **arg = (char **) fw_arg1; - char **env = (char **) fw_arg2; - struct callvectors *cv = (struct callvectors *) fw_arg3; - int i; - -#ifdef CONFIG_64BIT - char *ptr; - - printk("prom_init - MIPS64\n"); - /* save the PROM vectors for debugging use */ - debug_vectors = (struct callvectors *)signext((unsigned long)cv); - - /* arg[0] is "g", the rest is boot parameters */ - arcs_cmdline[0] = '\0'; - - for (i = 1; i < argc; i++) { - ptr = (char *)arg64((unsigned long)arg, i); - if ((strlen(arcs_cmdline) + strlen(ptr) + 1) >= - sizeof(arcs_cmdline)) - break; - strcat(arcs_cmdline, ptr); - strcat(arcs_cmdline, " "); - } - i = 0; - while (1) { - ptr = (char *)arg64((unsigned long)env, i); - if (! ptr) - break; - - if (strncmp("gtbase", ptr, strlen("gtbase")) == 0) { - marvell_base = simple_strtol(ptr + strlen("gtbase="), - NULL, 16); - - if ((marvell_base & 0xffffffff00000000) == 0) - marvell_base |= 0xffffffff00000000; - - printk("marvell_base set to 0x%016lx\n", marvell_base); - } - if (strncmp("cpuclock", ptr, strlen("cpuclock")) == 0) { - cpu_clock = simple_strtol(ptr + strlen("cpuclock="), - NULL, 10); - printk("cpu_clock set to %d\n", cpu_clock); - } - i++; - } - printk("arcs_cmdline: %s\n", arcs_cmdline); - -#else /* CONFIG_64BIT */ - /* save the PROM vectors for debugging use */ - debug_vectors = cv; - - /* arg[0] is "g", the rest is boot parameters */ - arcs_cmdline[0] = '\0'; - for (i = 1; i < argc; i++) { - if (strlen(arcs_cmdline) + strlen(arg[i] + 1) - >= sizeof(arcs_cmdline)) - break; - strcat(arcs_cmdline, arg[i]); - strcat(arcs_cmdline, " "); - } - - while (*env) { - if (strncmp("gtbase", *env, strlen("gtbase")) == 0) { - marvell_base = simple_strtol(*env + strlen("gtbase="), - NULL, 16); - } - if (strncmp("cpuclock", *env, strlen("cpuclock")) == 0) { - cpu_clock = simple_strtol(*env + strlen("cpuclock="), - NULL, 10); - } - env++; - } -#endif /* CONFIG_64BIT */ - - mips_machgroup = MACH_GROUP_MOMENCO; - mips_machtype = MACH_MOMENCO_OCELOT_C; - -#ifndef CONFIG_64BIT - debug_vectors->printf("Booting Linux kernel...\n"); -#endif -} - -void __init prom_free_prom_memory(void) -{ -} diff --git a/arch/mips/momentum/ocelot_c/reset.c b/arch/mips/momentum/ocelot_c/reset.c deleted file mode 100644 index 3fdcb64..0000000 --- a/arch/mips/momentum/ocelot_c/reset.c +++ /dev/null @@ -1,58 +0,0 @@ -/* - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - * - * Copyright (C) 1997, 2001 Ralf Baechle - * Copyright 2001 MontaVista Software Inc. - * Author: jsun@mvista.com or jsun@junsun.net - * - * Copyright (C) 2002 Momentum Computer Inc. - * Author: Matthew Dharm <mdharm@momenco.com> - * - * Louis Hamilton, Red Hat, Inc. - * hamilton@redhat.com [MIPS64 modifications] - */ -#include <linux/sched.h> -#include <linux/mm.h> -#include <asm/io.h> -#include <asm/pgtable.h> -#include <asm/processor.h> -#include <asm/reboot.h> -#include <asm/system.h> -#include <linux/delay.h> - -void momenco_ocelot_restart(char *command) -{ - /* base address of timekeeper portion of part */ - void *nvram = (void *) -#ifdef CONFIG_64BIT - 0xfffffffffc807000; -#else - 0xfc807000; -#endif - - /* Ask the NVRAM/RTC/watchdog chip to assert reset in 1/16 second */ - writeb(0x84, nvram + 0xff7); - - /* wait for the watchdog to go off */ - mdelay(100+(1000/16)); - - /* if the watchdog fails for some reason, let people know */ - printk(KERN_NOTICE "Watchdog reset failed\n"); -} - -void momenco_ocelot_halt(void) -{ - printk(KERN_NOTICE "\n** You can safely turn off the power\n"); - while (1) - __asm__(".set\tmips3\n\t" - "wait\n\t" - ".set\tmips0"); -} - -void momenco_ocelot_power_off(void) -{ - momenco_ocelot_halt(); -} diff --git a/arch/mips/momentum/ocelot_c/setup.c b/arch/mips/momentum/ocelot_c/setup.c deleted file mode 100644 index 0b6b233..0000000 --- a/arch/mips/momentum/ocelot_c/setup.c +++ /dev/null @@ -1,362 +0,0 @@ -/* - * BRIEF MODULE DESCRIPTION - * Momentum Computer Ocelot-C and -CS board dependent boot routines - * - * Copyright (C) 1996, 1997, 2001 Ralf Baechle - * Copyright (C) 2000 RidgeRun, Inc. - * Copyright (C) 2001 Red Hat, Inc. - * Copyright (C) 2002 Momentum Computer - * - * Author: Matthew Dharm, Momentum Computer - * mdharm@momenco.com - * - * Louis Hamilton, Red Hat, Inc. - * hamilton@redhat.com [MIPS64 modifications] - * - * Author: RidgeRun, Inc. - * glonnon@ridgerun.com, skranz@ridgerun.com, stevej@ridgerun.com - * - * Copyright 2001 MontaVista Software Inc. - * Author: jsun@mvista.com or jsun@junsun.net - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - * - * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED - * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF - * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN - * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, - * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT - * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF - * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON - * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT - * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF - * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - * You should have received a copy of the GNU General Public License along - * with this program; if not, write to the Free Software Foundation, Inc., - * 675 Mass Ave, Cambridge, MA 02139, USA. - * - */ -#include <linux/bcd.h> -#include <linux/init.h> -#include <linux/kernel.h> -#include <linux/types.h> -#include <linux/mm.h> -#include <linux/swap.h> -#include <linux/ioport.h> -#include <linux/sched.h> -#include <linux/interrupt.h> -#include <linux/pci.h> -#include <linux/pm.h> -#include <linux/timex.h> -#include <linux/vmalloc.h> -#include <linux/mv643xx.h> - -#include <asm/time.h> -#include <asm/bootinfo.h> -#include <asm/page.h> -#include <asm/io.h> -#include <asm/irq.h> -#include <asm/pci.h> -#include <asm/processor.h> -#include <asm/reboot.h> -#include <asm/marvell.h> -#include <linux/bootmem.h> -#include <linux/blkdev.h> -#include "ocelot_c_fpga.h" - -unsigned long marvell_base; -unsigned int cpu_clock; - -/* These functions are used for rebooting or halting the machine*/ -extern void momenco_ocelot_restart(char *command); -extern void momenco_ocelot_halt(void); -extern void momenco_ocelot_power_off(void); - -void momenco_time_init(void); - -static char reset_reason; - -void add_wired_entry(unsigned long entrylo0, unsigned long entrylo1, unsigned long entryhi, unsigned long pagemask); - -static unsigned long ENTRYLO(unsigned long paddr) -{ - return ((paddr & PAGE_MASK) | - (_PAGE_PRESENT | __READABLE | __WRITEABLE | _PAGE_GLOBAL | - _CACHE_UNCACHED)) >> 6; -} - -/* setup code for a handoff from a version 2 PMON 2000 PROM */ -void PMON_v2_setup(void) -{ - /* Some wired TLB entries for the MV64340 and perhiperals. The - MV64340 is going to be hit on every IRQ anyway - there's - absolutely no point in letting it be a random TLB entry, as - it'll just cause needless churning of the TLB. And we use - the other half for the serial port, which is just a PITA - otherwise :) - - Device Physical Virtual - MV64340 Internal Regs 0xf4000000 0xf4000000 - Ocelot-C[S] PLD (CS0) 0xfc000000 0xfc000000 - NVRAM (CS1) 0xfc800000 0xfc800000 - UARTs (CS2) 0xfd000000 0xfd000000 - Internal SRAM 0xfe000000 0xfe000000 - M-Systems DOC (CS3) 0xff000000 0xff000000 - */ - printk("PMON_v2_setup\n"); - -#ifdef CONFIG_64BIT - /* marvell and extra space */ - add_wired_entry(ENTRYLO(0xf4000000), ENTRYLO(0xf4010000), 0xfffffffff4000000, PM_64K); - /* fpga, rtc, and uart */ - add_wired_entry(ENTRYLO(0xfc000000), ENTRYLO(0xfd000000), 0xfffffffffc000000, PM_16M); - /* m-sys and internal SRAM */ - add_wired_entry(ENTRYLO(0xfe000000), ENTRYLO(0xff000000), 0xfffffffffe000000, PM_16M); - - marvell_base = 0xfffffffff4000000; -#else - /* marvell and extra space */ - add_wired_entry(ENTRYLO(0xf4000000), ENTRYLO(0xf4010000), 0xf4000000, PM_64K); - /* fpga, rtc, and uart */ - add_wired_entry(ENTRYLO(0xfc000000), ENTRYLO(0xfd000000), 0xfc000000, PM_16M); - /* m-sys and internal SRAM */ - add_wired_entry(ENTRYLO(0xfe000000), ENTRYLO(0xff000000), 0xfe000000, PM_16M); - - marvell_base = 0xf4000000; -#endif -} - -unsigned long m48t37y_get_time(void) -{ -#ifdef CONFIG_64BIT - unsigned char *rtc_base = (unsigned char*)0xfffffffffc800000; -#else - unsigned char* rtc_base = (unsigned char*)0xfc800000; -#endif - unsigned int year, month, day, hour, min, sec; - unsigned long flags; - - spin_lock_irqsave(&rtc_lock, flags); - /* stop the update */ - rtc_base[0x7ff8] = 0x40; - - year = BCD2BIN(rtc_base[0x7fff]); - year += BCD2BIN(rtc_base[0x7ff1]) * 100; - - month = BCD2BIN(rtc_base[0x7ffe]); - - day = BCD2BIN(rtc_base[0x7ffd]); - - hour = BCD2BIN(rtc_base[0x7ffb]); - min = BCD2BIN(rtc_base[0x7ffa]); - sec = BCD2BIN(rtc_base[0x7ff9]); - - /* start the update */ - rtc_base[0x7ff8] = 0x00; - spin_unlock_irqrestore(&rtc_lock, flags); - - return mktime(year, month, day, hour, min, sec); -} - -int m48t37y_set_time(unsigned long sec) -{ -#ifdef CONFIG_64BIT - unsigned char* rtc_base = (unsigned char*)0xfffffffffc800000; -#else - unsigned char* rtc_base = (unsigned char*)0xfc800000; -#endif - struct rtc_time tm; - unsigned long flags; - - /* convert to a more useful format -- note months count from 0 */ - to_tm(sec, &tm); - tm.tm_mon += 1; - - spin_lock_irqsave(&rtc_lock, flags); - /* enable writing */ - rtc_base[0x7ff8] = 0x80; - - /* year */ - rtc_base[0x7fff] = BIN2BCD(tm.tm_year % 100); - rtc_base[0x7ff1] = BIN2BCD(tm.tm_year / 100); - - /* month */ - rtc_base[0x7ffe] = BIN2BCD(tm.tm_mon); - - /* day */ - rtc_base[0x7ffd] = BIN2BCD(tm.tm_mday); - - /* hour/min/sec */ - rtc_base[0x7ffb] = BIN2BCD(tm.tm_hour); - rtc_base[0x7ffa] = BIN2BCD(tm.tm_min); - rtc_base[0x7ff9] = BIN2BCD(tm.tm_sec); - - /* day of week -- not really used, but let's keep it up-to-date */ - rtc_base[0x7ffc] = BIN2BCD(tm.tm_wday + 1); - - /* disable writing */ - rtc_base[0x7ff8] = 0x00; - spin_unlock_irqrestore(&rtc_lock, flags); - - return 0; -} - -void __init plat_timer_setup(struct irqaction *irq) -{ - setup_irq(7, irq); -} - -void momenco_time_init(void) -{ -#ifdef CONFIG_CPU_SR71000 - mips_hpt_frequency = cpu_clock; -#elif defined(CONFIG_CPU_RM7000) - mips_hpt_frequency = cpu_clock / 2; -#else -#error Unknown CPU for this board -#endif - printk("momenco_time_init cpu_clock=%d\n", cpu_clock); - - rtc_mips_get_time = m48t37y_get_time; - rtc_mips_set_time = m48t37y_set_time; -} - -void __init plat_mem_setup(void) -{ - unsigned int tmpword; - - board_time_init = momenco_time_init; - - _machine_restart = momenco_ocelot_restart; - _machine_halt = momenco_ocelot_halt; - pm_power_off = momenco_ocelot_power_off; - - /* - * initrd_start = (unsigned long)ocelot_initrd_start; - * initrd_end = (unsigned long)ocelot_initrd_start + (ulong)ocelot_initrd_size; - * initrd_below_start_ok = 1; - */ - - /* do handoff reconfiguration */ - PMON_v2_setup(); - - /* shut down ethernet ports, just to be sure our memory doesn't get - * corrupted by random ethernet traffic. - */ - MV_WRITE(MV643XX_ETH_TRANSMIT_QUEUE_COMMAND_REG(0), 0xff << 8); - MV_WRITE(MV643XX_ETH_TRANSMIT_QUEUE_COMMAND_REG(1), 0xff << 8); - MV_WRITE(MV643XX_ETH_RECEIVE_QUEUE_COMMAND_REG(0), 0xff << 8); - MV_WRITE(MV643XX_ETH_RECEIVE_QUEUE_COMMAND_REG(1), 0xff << 8); - do {} - while (MV_READ(MV643XX_ETH_RECEIVE_QUEUE_COMMAND_REG(0)) & 0xff); - do {} - while (MV_READ(MV643XX_ETH_RECEIVE_QUEUE_COMMAND_REG(1)) & 0xff); - do {} - while (MV_READ(MV643XX_ETH_TRANSMIT_QUEUE_COMMAND_REG(0)) & 0xff); - do {} - while (MV_READ(MV643XX_ETH_TRANSMIT_QUEUE_COMMAND_REG(1)) & 0xff); - MV_WRITE(MV643XX_ETH_PORT_SERIAL_CONTROL_REG(0), - MV_READ(MV643XX_ETH_PORT_SERIAL_CONTROL_REG(0)) & ~1); - MV_WRITE(MV643XX_ETH_PORT_SERIAL_CONTROL_REG(1), - MV_READ(MV643XX_ETH_PORT_SERIAL_CONTROL_REG(1)) & ~1); - - /* Turn off the Bit-Error LED */ - OCELOT_FPGA_WRITE(0x80, CLR); - - tmpword = OCELOT_FPGA_READ(BOARDREV); -#ifdef CONFIG_CPU_SR71000 - if (tmpword < 26) - printk("Momenco Ocelot-CS: Board Assembly Rev. %c\n", - 'A'+tmpword); - else - printk("Momenco Ocelot-CS: Board Assembly Revision #0x%x\n", - tmpword); -#else - if (tmpword < 26) - printk("Momenco Ocelot-C: Board Assembly Rev. %c\n", - 'A'+tmpword); - else - printk("Momenco Ocelot-C: Board Assembly Revision #0x%x\n", - tmpword); -#endif - - tmpword = OCELOT_FPGA_READ(FPGA_REV); - printk("FPGA Rev: %d.%d\n", tmpword>>4, tmpword&15); - tmpword = OCELOT_FPGA_READ(RESET_STATUS); - printk("Reset reason: 0x%x\n", tmpword); - switch (tmpword) { - case 0x1: - printk(" - Power-up reset\n"); - break; - case 0x2: - printk(" - Push-button reset\n"); - break; - case 0x4: - printk(" - cPCI bus reset\n"); - break; - case 0x8: - printk(" - Watchdog reset\n"); - break; - case 0x10: - printk(" - Software reset\n"); - break; - default: - printk(" - Unknown reset cause\n"); - } - reset_reason = tmpword; - OCELOT_FPGA_WRITE(0xff, RESET_STATUS); - - tmpword = OCELOT_FPGA_READ(CPCI_ID); - printk("cPCI ID register: 0x%02x\n", tmpword); - printk(" - Slot number: %d\n", tmpword & 0x1f); - printk(" - PCI bus present: %s\n", tmpword & 0x40 ? "yes" : "no"); - printk(" - System Slot: %s\n", tmpword & 0x20 ? "yes" : "no"); - - tmpword = OCELOT_FPGA_READ(BOARD_STATUS); - printk("Board Status register: 0x%02x\n", tmpword); - printk(" - User jumper: %s\n", (tmpword & 0x80)?"installed":"absent"); - printk(" - Boot flash write jumper: %s\n", (tmpword&0x40)?"installed":"absent"); - printk(" - L3 Cache size: %d MiB\n", (1<<((tmpword&12) >> 2))&~1); - printk(" - SDRAM size: %d MiB\n", 1<<(6+(tmpword&3))); - - switch(tmpword &3) { - case 3: - /* 512MiB */ - add_memory_region(0x0, 0x200<<20, BOOT_MEM_RAM); - break; - case 2: - /* 256MiB */ - add_memory_region(0x0, 0x100<<20, BOOT_MEM_RAM); - break; - case 1: - /* 128MiB */ - add_memory_region(0x0, 0x80<<20, BOOT_MEM_RAM); - break; - case 0: - /* 1GiB -- needs CONFIG_HIGHMEM */ - add_memory_region(0x0, 0x400<<20, BOOT_MEM_RAM); - break; - } -} - -/* - * This needs to be one of the first initcalls, because no I/O port access - * can work before this - */ -static int io_base_ioremap(void) -{ - void __iomem * io_remap_range = ioremap(0xc0000000UL, 0x10000); - - if (!io_remap_range) - panic("Could not ioremap I/O port range"); - - set_io_port_base((unsigned long) io_remap_range); - - return 0; -} - -module_init(io_base_ioremap); diff --git a/arch/mips/momentum/ocelot_c/uart-irq.c b/arch/mips/momentum/ocelot_c/uart-irq.c deleted file mode 100644 index de1a31e..0000000 --- a/arch/mips/momentum/ocelot_c/uart-irq.c +++ /dev/null @@ -1,91 +0,0 @@ -/* - * Copyright 2002 Momentum Computer - * Author: mdharm@momenco.com - * - * arch/mips/momentum/ocelot_c/uart-irq.c - * Interrupt routines for UARTs. Interrupt numbers are assigned from - * 80 to 81 (2 interrupt sources). - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - */ - -#include <linux/module.h> -#include <linux/interrupt.h> -#include <linux/irq.h> -#include <linux/kernel.h> -#include <linux/sched.h> -#include <linux/kernel_stat.h> -#include <asm/io.h> -#include <asm/irq.h> -#include "ocelot_c_fpga.h" - -static inline int ls1bit8(unsigned int x) -{ - int b = 7, s; - - s = 4; if (((unsigned char)(x << 4)) == 0) s = 0; b -= s; x <<= s; - s = 2; if (((unsigned char)(x << 2)) == 0) s = 0; b -= s; x <<= s; - s = 1; if (((unsigned char)(x << 1)) == 0) s = 0; b -= s; - - return b; -} - -/* mask off an interrupt -- 0 is enable, 1 is disable */ -static inline void mask_uart_irq(unsigned int irq) -{ - uint8_t value; - - value = OCELOT_FPGA_READ(UART_INTMASK); - value |= 1 << (irq - 74); - OCELOT_FPGA_WRITE(value, UART_INTMASK); - - /* read the value back to assure that it's really been written */ - value = OCELOT_FPGA_READ(UART_INTMASK); -} - -/* unmask an interrupt -- 0 is enable, 1 is disable */ -static inline void unmask_uart_irq(unsigned int irq) -{ - uint8_t value; - - value = OCELOT_FPGA_READ(UART_INTMASK); - value &= ~(1 << (irq - 74)); - OCELOT_FPGA_WRITE(value, UART_INTMASK); - - /* read the value back to assure that it's really been written */ - value = OCELOT_FPGA_READ(UART_INTMASK); -} - -/* - * Interrupt handler for interrupts coming from the FPGA chip. - */ -void ll_uart_irq(void) -{ - unsigned int irq_src, irq_mask; - - /* read the interrupt status registers */ - irq_src = OCELOT_FPGA_READ(UART_INTSTAT); - irq_mask = OCELOT_FPGA_READ(UART_INTMASK); - - /* mask for just the interrupts we want */ - irq_src &= ~irq_mask; - - do_IRQ(ls1bit8(irq_src) + 74); -} - -struct irq_chip uart_irq_type = { - .name = "UART/FPGA", - .ack = mask_uart_irq, - .mask = mask_uart_irq, - .mask_ack = mask_uart_irq, - .unmask = unmask_uart_irq, -}; - -void uart_irq_init(void) -{ - set_irq_chip_and_handler(80, &uart_irq_type, handle_level_irq); - set_irq_chip_and_handler(81, &uart_irq_type, handle_level_irq); -} diff --git a/arch/mips/pci/Makefile b/arch/mips/pci/Makefile index 3ff56b8..a3e741e 100644 --- a/arch/mips/pci/Makefile +++ b/arch/mips/pci/Makefile @@ -31,7 +31,6 @@ obj-$(CONFIG_SOC_PNX8550) += fixup-pnx8550.o ops-pnx8550.o obj-$(CONFIG_MIPS_MALTA) += fixup-malta.o obj-$(CONFIG_MOMENCO_OCELOT) += fixup-ocelot.o pci-ocelot.o obj-$(CONFIG_MOMENCO_OCELOT_3) += fixup-ocelot3.o -obj-$(CONFIG_MOMENCO_OCELOT_C) += fixup-ocelot-c.o pci-ocelot-c.o obj-$(CONFIG_PMC_YOSEMITE) += fixup-yosemite.o ops-titan.o ops-titan-ht.o \ pci-yosemite.o obj-$(CONFIG_SGI_IP27) += ops-bridge.o pci-ip27.o diff --git a/arch/mips/pci/fixup-ocelot-c.c b/arch/mips/pci/fixup-ocelot-c.c deleted file mode 100644 index 6616648..0000000 --- a/arch/mips/pci/fixup-ocelot-c.c +++ /dev/null @@ -1,41 +0,0 @@ -/* - * Copyright 2002 Momentum Computer Inc. - * Author: Matthew Dharm <mdharm@momenco.com> - * - * Based on work for the Linux port to the Ocelot board, which is - * Copyright 2001 MontaVista Software Inc. - * Author: Jun Sun, jsun@mvista.com or jsun@junsun.net - * - * arch/mips/momentum/ocelot_g/pci.c - * Board-specific PCI routines for mv64340 controller. - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - */ -#include <linux/types.h> -#include <linux/pci.h> -#include <linux/kernel.h> -#include <linux/init.h> - -int __init pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin) -{ - int bus = dev->bus->number; - - if (bus == 0 && slot == 1) - return 2; /* PCI-X A */ - if (bus == 1 && slot == 1) - return 12; /* PCI-X B */ - if (bus == 1 && slot == 2) - return 4; /* PCI B */ - -return 0; - panic("Whooops in pcibios_map_irq"); -} - -/* Do platform specific device initialization at pci_enable_device() time */ -int pcibios_plat_dev_init(struct pci_dev *dev) -{ - return 0; -} diff --git a/arch/mips/pci/pci-ocelot-c.c b/arch/mips/pci/pci-ocelot-c.c deleted file mode 100644 index 027759f..0000000 --- a/arch/mips/pci/pci-ocelot-c.c +++ /dev/null @@ -1,145 +0,0 @@ -/* - * This file is subject to the terms and conditions of the GNU General Public - * License. See the file "COPYING" in the main directory of this archive - * for more details. - * - * Copyright (C) 2004, 06 by Ralf Baechle (ralf@linux-mips.org) - */ - -#include <linux/types.h> -#include <linux/pci.h> -#include <linux/mv643xx.h> - -#include <linux/init.h> - -#include <asm/marvell.h> - -/* - * We assume the address ranges have already been setup appropriately by - * the firmware. PMON in case of the Ocelot C does that. - */ -static struct resource mv_pci_io_mem0_resource = { - .name = "MV64340 PCI0 IO MEM", - .flags = IORESOURCE_IO -}; - -static struct resource mv_pci_mem0_resource = { - .name = "MV64340 PCI0 MEM", - .flags = IORESOURCE_MEM -}; - -static struct mv_pci_controller mv_bus0_controller = { - .pcic = { - .pci_ops = &mv_pci_ops, - .mem_resource = &mv_pci_mem0_resource, - .io_resource = &mv_pci_io_mem0_resource, - }, - .config_addr = MV64340_PCI_0_CONFIG_ADDR, - .config_vreg = MV64340_PCI_0_CONFIG_DATA_VIRTUAL_REG, -}; - -static uint32_t mv_io_base, mv_io_size; - -static void mv64340_pci0_init(void) -{ - uint32_t mem0_base, mem0_size; - uint32_t io_base, io_size; - - io_base = MV_READ(MV64340_PCI_0_IO_BASE_ADDR) << 16; - io_size = (MV_READ(MV64340_PCI_0_IO_SIZE) + 1) << 16; - mem0_base = MV_READ(MV64340_PCI_0_MEMORY0_BASE_ADDR) << 16; - mem0_size = (MV_READ(MV64340_PCI_0_MEMORY0_SIZE) + 1) << 16; - - mv_pci_io_mem0_resource.start = 0; - mv_pci_io_mem0_resource.end = io_size - 1; - mv_pci_mem0_resource.start = mem0_base; - mv_pci_mem0_resource.end = mem0_base + mem0_size - 1; - mv_bus0_controller.pcic.mem_offset = mem0_base; - mv_bus0_controller.pcic.io_offset = 0; - - ioport_resource.end = io_size - 1; - - register_pci_controller(&mv_bus0_controller.pcic); - - mv_io_base = io_base; - mv_io_size = io_size; -} - -static struct resource mv_pci_io_mem1_resource = { - .name = "MV64340 PCI1 IO MEM", - .flags = IORESOURCE_IO -}; - -static struct resource mv_pci_mem1_resource = { - .name = "MV64340 PCI1 MEM", - .flags = IORESOURCE_MEM -}; - -static struct mv_pci_controller mv_bus1_controller = { - .pcic = { - .pci_ops = &mv_pci_ops, - .mem_resource = &mv_pci_mem1_resource, - .io_resource = &mv_pci_io_mem1_resource, - }, - .config_addr = MV64340_PCI_1_CONFIG_ADDR, - .config_vreg = MV64340_PCI_1_CONFIG_DATA_VIRTUAL_REG, -}; - -static __init void mv64340_pci1_init(void) -{ - uint32_t mem0_base, mem0_size; - uint32_t io_base, io_size; - - io_base = MV_READ(MV64340_PCI_1_IO_BASE_ADDR) << 16; - io_size = (MV_READ(MV64340_PCI_1_IO_SIZE) + 1) << 16; - mem0_base = MV_READ(MV64340_PCI_1_MEMORY0_BASE_ADDR) << 16; - mem0_size = (MV_READ(MV64340_PCI_1_MEMORY0_SIZE) + 1) << 16; - - /* - * Here we assume the I/O window of second bus to be contiguous with - * the first. A gap is no problem but would waste address space for - * remapping the port space. - */ - mv_pci_io_mem1_resource.start = mv_io_size; - mv_pci_io_mem1_resource.end = mv_io_size + io_size - 1; - mv_pci_mem1_resource.start = mem0_base; - mv_pci_mem1_resource.end = mem0_base + mem0_size - 1; - mv_bus1_controller.pcic.mem_offset = mem0_base; - mv_bus1_controller.pcic.io_offset = 0; - - ioport_resource.end = io_base + io_size -mv_io_base - 1; - - register_pci_controller(&mv_bus1_controller.pcic); - - mv_io_size = io_base + io_size - mv_io_base; -} - -static __init int __init ocelot_c_pci_init(void) -{ - unsigned long io_v_base; - uint32_t enable; - - enable = ~MV_READ(MV64340_BASE_ADDR_ENABLE); - - /* - * We require at least one enabled I/O or PCI memory window or we - * will ignore this PCI bus. We ignore PCI windows 1, 2 and 3. - */ - if (enable & (0x01 << 9) || enable & (0x01 << 10)) - mv64340_pci0_init(); - - if (enable & (0x01 << 14) || enable & (0x01 << 15)) - mv64340_pci1_init(); - - if (mv_io_size) { - io_v_base = (unsigned long) ioremap(mv_io_base, mv_io_size); - if (!io_v_base) - panic("Could not ioremap I/O port range"); - - set_io_port_base(io_v_base); - } - - return 0; -} - -arch_initcall(ocelot_c_pci_init); |
