diff options
Diffstat (limited to 'arch/x86/kernel/uprobes.c')
| -rw-r--r-- | arch/x86/kernel/uprobes.c | 213 |
1 files changed, 138 insertions, 75 deletions
diff --git a/arch/x86/kernel/uprobes.c b/arch/x86/kernel/uprobes.c index 2ebadb2..159ca52 100644 --- a/arch/x86/kernel/uprobes.c +++ b/arch/x86/kernel/uprobes.c @@ -41,8 +41,11 @@ /* Instruction will modify TF, don't change it */ #define UPROBE_FIX_SETF 0x04 -#define UPROBE_FIX_RIP_AX 0x08 -#define UPROBE_FIX_RIP_CX 0x10 +#define UPROBE_FIX_RIP_SI 0x08 +#define UPROBE_FIX_RIP_DI 0x10 +#define UPROBE_FIX_RIP_BX 0x20 +#define UPROBE_FIX_RIP_MASK \ + (UPROBE_FIX_RIP_SI | UPROBE_FIX_RIP_DI | UPROBE_FIX_RIP_BX) #define UPROBE_TRAP_NR UINT_MAX @@ -251,9 +254,9 @@ static inline bool is_64bit_mm(struct mm_struct *mm) * If arch_uprobe->insn doesn't use rip-relative addressing, return * immediately. Otherwise, rewrite the instruction so that it accesses * its memory operand indirectly through a scratch register. Set - * def->fixups and def->riprel_target accordingly. (The contents of the - * scratch register will be saved before we single-step the modified - * instruction, and restored afterward). + * def->fixups accordingly. (The contents of the scratch register + * will be saved before we single-step the modified instruction, + * and restored afterward). * * We do this because a rip-relative instruction can access only a * relatively small area (+/- 2 GB from the instruction), and the XOL @@ -264,28 +267,120 @@ static inline bool is_64bit_mm(struct mm_struct *mm) * * Some useful facts about rip-relative instructions: * - * - There's always a modrm byte. + * - There's always a modrm byte with bit layout "00 reg 101". * - There's never a SIB byte. * - The displacement is always 4 bytes. + * - REX.B=1 bit in REX prefix, which normally extends r/m field, + * has no effect on rip-relative mode. It doesn't make modrm byte + * with r/m=101 refer to register 1101 = R13. */ static void riprel_analyze(struct arch_uprobe *auprobe, struct insn *insn) { u8 *cursor; u8 reg; + u8 reg2; if (!insn_rip_relative(insn)) return; /* - * insn_rip_relative() would have decoded rex_prefix, modrm. + * insn_rip_relative() would have decoded rex_prefix, vex_prefix, modrm. * Clear REX.b bit (extension of MODRM.rm field): - * we want to encode rax/rcx, not r8/r9. + * we want to encode low numbered reg, not r8+. */ if (insn->rex_prefix.nbytes) { cursor = auprobe->insn + insn_offset_rex_prefix(insn); - *cursor &= 0xfe; /* Clearing REX.B bit */ + /* REX byte has 0100wrxb layout, clearing REX.b bit */ + *cursor &= 0xfe; } + /* + * Similar treatment for VEX3 prefix. + * TODO: add XOP/EVEX treatment when insn decoder supports them + */ + if (insn->vex_prefix.nbytes == 3) { + /* + * vex2: c5 rvvvvLpp (has no b bit) + * vex3/xop: c4/8f rxbmmmmm wvvvvLpp + * evex: 62 rxbR00mm wvvvv1pp zllBVaaa + * (evex will need setting of both b and x since + * in non-sib encoding evex.x is 4th bit of MODRM.rm) + * Setting VEX3.b (setting because it has inverted meaning): + */ + cursor = auprobe->insn + insn_offset_vex_prefix(insn) + 1; + *cursor |= 0x20; + } + + /* + * Convert from rip-relative addressing to register-relative addressing + * via a scratch register. + * + * This is tricky since there are insns with modrm byte + * which also use registers not encoded in modrm byte: + * [i]div/[i]mul: implicitly use dx:ax + * shift ops: implicitly use cx + * cmpxchg: implicitly uses ax + * cmpxchg8/16b: implicitly uses dx:ax and bx:cx + * Encoding: 0f c7/1 modrm + * The code below thinks that reg=1 (cx), chooses si as scratch. + * mulx: implicitly uses dx: mulx r/m,r1,r2 does r1:r2 = dx * r/m. + * First appeared in Haswell (BMI2 insn). It is vex-encoded. + * Example where none of bx,cx,dx can be used as scratch reg: + * c4 e2 63 f6 0d disp32 mulx disp32(%rip),%ebx,%ecx + * [v]pcmpistri: implicitly uses cx, xmm0 + * [v]pcmpistrm: implicitly uses xmm0 + * [v]pcmpestri: implicitly uses ax, dx, cx, xmm0 + * [v]pcmpestrm: implicitly uses ax, dx, xmm0 + * Evil SSE4.2 string comparison ops from hell. + * maskmovq/[v]maskmovdqu: implicitly uses (ds:rdi) as destination. + * Encoding: 0f f7 modrm, 66 0f f7 modrm, vex-encoded: c5 f9 f7 modrm. + * Store op1, byte-masked by op2 msb's in each byte, to (ds:rdi). + * AMD says it has no 3-operand form (vex.vvvv must be 1111) + * and that it can have only register operands, not mem + * (its modrm byte must have mode=11). + * If these restrictions will ever be lifted, + * we'll need code to prevent selection of di as scratch reg! + * + * Summary: I don't know any insns with modrm byte which + * use SI register implicitly. DI register is used only + * by one insn (maskmovq) and BX register is used + * only by one too (cmpxchg8b). + * BP is stack-segment based (may be a problem?). + * AX, DX, CX are off-limits (many implicit users). + * SP is unusable (it's stack pointer - think about "pop mem"; + * also, rsp+disp32 needs sib encoding -> insn length change). + */ + reg = MODRM_REG(insn); /* Fetch modrm.reg */ + reg2 = 0xff; /* Fetch vex.vvvv */ + if (insn->vex_prefix.nbytes == 2) + reg2 = insn->vex_prefix.bytes[1]; + else if (insn->vex_prefix.nbytes == 3) + reg2 = insn->vex_prefix.bytes[2]; + /* + * TODO: add XOP, EXEV vvvv reading. + * + * vex.vvvv field is in bits 6-3, bits are inverted. + * But in 32-bit mode, high-order bit may be ignored. + * Therefore, let's consider only 3 low-order bits. + */ + reg2 = ((reg2 >> 3) & 0x7) ^ 0x7; + /* + * Register numbering is ax,cx,dx,bx, sp,bp,si,di, r8..r15. + * + * Choose scratch reg. Order is important: must not select bx + * if we can use si (cmpxchg8b case!) + */ + if (reg != 6 && reg2 != 6) { + reg2 = 6; + auprobe->def.fixups |= UPROBE_FIX_RIP_SI; + } else if (reg != 7 && reg2 != 7) { + reg2 = 7; + auprobe->def.fixups |= UPROBE_FIX_RIP_DI; + /* TODO (paranoia): force maskmovq to not use di */ + } else { + reg2 = 3; + auprobe->def.fixups |= UPROBE_FIX_RIP_BX; + } /* * Point cursor at the modrm byte. The next 4 bytes are the * displacement. Beyond the displacement, for some instructions, @@ -293,43 +388,21 @@ static void riprel_analyze(struct arch_uprobe *auprobe, struct insn *insn) */ cursor = auprobe->insn + insn_offset_modrm(insn); /* - * Convert from rip-relative addressing to indirect addressing - * via a scratch register. Change the r/m field from 0x5 (%rip) - * to 0x0 (%rax) or 0x1 (%rcx), and squeeze out the offset field. + * Change modrm from "00 reg 101" to "10 reg reg2". Example: + * 89 05 disp32 mov %eax,disp32(%rip) becomes + * 89 86 disp32 mov %eax,disp32(%rsi) */ - reg = MODRM_REG(insn); - if (reg == 0) { - /* - * The register operand (if any) is either the A register - * (%rax, %eax, etc.) or (if the 0x4 bit is set in the - * REX prefix) %r8. In any case, we know the C register - * is NOT the register operand, so we use %rcx (register - * #1) for the scratch register. - */ - auprobe->def.fixups |= UPROBE_FIX_RIP_CX; - /* Change modrm from 00 000 101 to 00 000 001. */ - *cursor = 0x1; - } else { - /* Use %rax (register #0) for the scratch register. */ - auprobe->def.fixups |= UPROBE_FIX_RIP_AX; - /* Change modrm from 00 xxx 101 to 00 xxx 000 */ - *cursor = (reg << 3); - } - - /* Target address = address of next instruction + (signed) offset */ - auprobe->def.riprel_target = (long)insn->length + insn->displacement.value; - - /* Displacement field is gone; slide immediate field (if any) over. */ - if (insn->immediate.nbytes) { - cursor++; - memmove(cursor, cursor + insn->displacement.nbytes, insn->immediate.nbytes); - } + *cursor = 0x80 | (reg << 3) | reg2; } static inline unsigned long * scratch_reg(struct arch_uprobe *auprobe, struct pt_regs *regs) { - return (auprobe->def.fixups & UPROBE_FIX_RIP_AX) ? ®s->ax : ®s->cx; + if (auprobe->def.fixups & UPROBE_FIX_RIP_SI) + return ®s->si; + if (auprobe->def.fixups & UPROBE_FIX_RIP_DI) + return ®s->di; + return ®s->bx; } /* @@ -338,31 +411,22 @@ scratch_reg(struct arch_uprobe *auprobe, struct pt_regs *regs) */ static void riprel_pre_xol(struct arch_uprobe *auprobe, struct pt_regs *regs) { - if (auprobe->def.fixups & (UPROBE_FIX_RIP_AX | UPROBE_FIX_RIP_CX)) { + if (auprobe->def.fixups & UPROBE_FIX_RIP_MASK) { struct uprobe_task *utask = current->utask; unsigned long *sr = scratch_reg(auprobe, regs); utask->autask.saved_scratch_register = *sr; - *sr = utask->vaddr + auprobe->def.riprel_target; + *sr = utask->vaddr + auprobe->def.ilen; } } -static void riprel_post_xol(struct arch_uprobe *auprobe, struct pt_regs *regs, - long *correction) +static void riprel_post_xol(struct arch_uprobe *auprobe, struct pt_regs *regs) { - if (auprobe->def.fixups & (UPROBE_FIX_RIP_AX | UPROBE_FIX_RIP_CX)) { + if (auprobe->def.fixups & UPROBE_FIX_RIP_MASK) { struct uprobe_task *utask = current->utask; unsigned long *sr = scratch_reg(auprobe, regs); *sr = utask->autask.saved_scratch_register; - /* - * The original instruction includes a displacement, and so - * is 4 bytes longer than what we've just single-stepped. - * Caller may need to apply other fixups to handle stuff - * like "jmpq *...(%rip)" and "callq *...(%rip)". - */ - if (correction) - *correction += 4; } } #else /* 32-bit: */ @@ -379,8 +443,7 @@ static void riprel_analyze(struct arch_uprobe *auprobe, struct insn *insn) static void riprel_pre_xol(struct arch_uprobe *auprobe, struct pt_regs *regs) { } -static void riprel_post_xol(struct arch_uprobe *auprobe, struct pt_regs *regs, - long *correction) +static void riprel_post_xol(struct arch_uprobe *auprobe, struct pt_regs *regs) { } #endif /* CONFIG_X86_64 */ @@ -414,13 +477,30 @@ static int push_ret_address(struct pt_regs *regs, unsigned long ip) return 0; } +/* + * We have to fix things up as follows: + * + * Typically, the new ip is relative to the copied instruction. We need + * to make it relative to the original instruction (FIX_IP). Exceptions + * are return instructions and absolute or indirect jump or call instructions. + * + * If the single-stepped instruction was a call, the return address that + * is atop the stack is the address following the copied instruction. We + * need to make it the address following the original instruction (FIX_CALL). + * + * If the original instruction was a rip-relative instruction such as + * "movl %edx,0xnnnn(%rip)", we have instead executed an equivalent + * instruction using a scratch register -- e.g., "movl %edx,0xnnnn(%rsi)". + * We need to restore the contents of the scratch register + * (FIX_RIP_reg). + */ static int default_post_xol_op(struct arch_uprobe *auprobe, struct pt_regs *regs) { struct uprobe_task *utask = current->utask; - long correction = (long)(utask->vaddr - utask->xol_vaddr); - riprel_post_xol(auprobe, regs, &correction); + riprel_post_xol(auprobe, regs); if (auprobe->def.fixups & UPROBE_FIX_IP) { + long correction = utask->vaddr - utask->xol_vaddr; regs->ip += correction; } else if (auprobe->def.fixups & UPROBE_FIX_CALL) { regs->sp += sizeof_long(); @@ -436,7 +516,7 @@ static int default_post_xol_op(struct arch_uprobe *auprobe, struct pt_regs *regs static void default_abort_op(struct arch_uprobe *auprobe, struct pt_regs *regs) { - riprel_post_xol(auprobe, regs, NULL); + riprel_post_xol(auprobe, regs); } static struct uprobe_xol_ops default_xol_ops = { @@ -720,23 +800,6 @@ bool arch_uprobe_xol_was_trapped(struct task_struct *t) * single-step, we single-stepped a copy of the instruction. * * This function prepares to resume execution after the single-step. - * We have to fix things up as follows: - * - * Typically, the new ip is relative to the copied instruction. We need - * to make it relative to the original instruction (FIX_IP). Exceptions - * are return instructions and absolute or indirect jump or call instructions. - * - * If the single-stepped instruction was a call, the return address that - * is atop the stack is the address following the copied instruction. We - * need to make it the address following the original instruction (FIX_CALL). - * - * If the original instruction was a rip-relative instruction such as - * "movl %edx,0xnnnn(%rip)", we have instead executed an equivalent - * instruction using a scratch register -- e.g., "movl %edx,(%rax)". - * We need to restore the contents of the scratch register and adjust - * the ip, keeping in mind that the instruction we executed is 4 bytes - * shorter than the original instruction (since we squeezed out the offset - * field). (FIX_RIP_AX or FIX_RIP_CX) */ int arch_uprobe_post_xol(struct arch_uprobe *auprobe, struct pt_regs *regs) { |
