diff options
Diffstat (limited to 'arch/x86/kernel/numaq_32.c')
-rw-r--r-- | arch/x86/kernel/numaq_32.c | 307 |
1 files changed, 293 insertions, 14 deletions
diff --git a/arch/x86/kernel/numaq_32.c b/arch/x86/kernel/numaq_32.c index f2191d4..0cc41a1 100644 --- a/arch/x86/kernel/numaq_32.c +++ b/arch/x86/kernel/numaq_32.c @@ -3,7 +3,7 @@ * * Copyright (C) 2002, IBM Corp. * - * All rights reserved. + * All rights reserved. * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -23,17 +23,18 @@ * Send feedback to <gone@us.ibm.com> */ -#include <linux/mm.h> +#include <linux/nodemask.h> #include <linux/bootmem.h> #include <linux/mmzone.h> #include <linux/module.h> -#include <linux/nodemask.h> -#include <asm/numaq.h> -#include <asm/topology.h> +#include <linux/mm.h> + #include <asm/processor.h> +#include <asm/topology.h> #include <asm/genapic.h> -#include <asm/e820.h> +#include <asm/numaq.h> #include <asm/setup.h> +#include <asm/e820.h> #define MB_TO_PAGES(addr) ((addr) << (20 - PAGE_SHIFT)) @@ -91,19 +92,20 @@ static int __init numaq_pre_time_init(void) } int found_numaq; + /* * Have to match translation table entries to main table entries by counter * hence the mpc_record variable .... can't see a less disgusting way of * doing this .... */ struct mpc_config_translation { - unsigned char mpc_type; - unsigned char trans_len; - unsigned char trans_type; - unsigned char trans_quad; - unsigned char trans_global; - unsigned char trans_local; - unsigned short trans_reserved; + unsigned char mpc_type; + unsigned char trans_len; + unsigned char trans_type; + unsigned char trans_quad; + unsigned char trans_global; + unsigned char trans_local; + unsigned short trans_reserved; }; /* x86_quirks member */ @@ -236,7 +238,7 @@ static int __init numaq_setup_ioapic_ids(void) static int __init numaq_update_genapic(void) { - genapic->wakeup_cpu = wakeup_secondary_cpu_via_nmi; + apic->wakeup_cpu = wakeup_secondary_cpu_via_nmi; return 0; } @@ -291,3 +293,280 @@ int __init get_memcfg_numaq(void) smp_dump_qct(); return 1; } + +/* + * APIC driver for the IBM NUMAQ chipset. + */ +#define APIC_DEFINITION 1 +#include <linux/threads.h> +#include <linux/cpumask.h> +#include <asm/mpspec.h> +#include <asm/genapic.h> +#include <asm/fixmap.h> +#include <asm/apicdef.h> +#include <asm/ipi.h> +#include <linux/kernel.h> +#include <linux/string.h> +#include <linux/init.h> +#include <linux/numa.h> +#include <linux/smp.h> +#include <asm/numaq.h> +#include <asm/io.h> +#include <linux/mmzone.h> +#include <linux/nodemask.h> + +#define NUMAQ_APIC_DFR_VALUE (APIC_DFR_CLUSTER) + +static inline unsigned int numaq_get_apic_id(unsigned long x) +{ + return (x >> 24) & 0x0F; +} + +static inline void numaq_send_IPI_mask(const struct cpumask *mask, int vector) +{ + default_send_IPI_mask_sequence_logical(mask, vector); +} + +static inline void numaq_send_IPI_allbutself(int vector) +{ + default_send_IPI_mask_allbutself_logical(cpu_online_mask, vector); +} + +static inline void numaq_send_IPI_all(int vector) +{ + numaq_send_IPI_mask(cpu_online_mask, vector); +} + +extern void numaq_mps_oem_check(struct mpc_table *, char *, char *); + +#define NUMAQ_TRAMPOLINE_PHYS_LOW (0x8) +#define NUMAQ_TRAMPOLINE_PHYS_HIGH (0xa) + +/* + * Because we use NMIs rather than the INIT-STARTUP sequence to + * bootstrap the CPUs, the APIC may be in a weird state. Kick it: + */ +static inline void numaq_smp_callin_clear_local_apic(void) +{ + clear_local_APIC(); +} + +static inline void +numaq_store_NMI_vector(unsigned short *high, unsigned short *low) +{ + printk("Storing NMI vector\n"); + *high = + *((volatile unsigned short *)phys_to_virt(NUMAQ_TRAMPOLINE_PHYS_HIGH)); + *low = + *((volatile unsigned short *)phys_to_virt(NUMAQ_TRAMPOLINE_PHYS_LOW)); +} + +static inline const cpumask_t *numaq_target_cpus(void) +{ + return &CPU_MASK_ALL; +} + +static inline unsigned long +numaq_check_apicid_used(physid_mask_t bitmap, int apicid) +{ + return physid_isset(apicid, bitmap); +} + +static inline unsigned long numaq_check_apicid_present(int bit) +{ + return physid_isset(bit, phys_cpu_present_map); +} + +#define apicid_cluster(apicid) (apicid & 0xF0) + +static inline int numaq_apic_id_registered(void) +{ + return 1; +} + +static inline void numaq_init_apic_ldr(void) +{ + /* Already done in NUMA-Q firmware */ +} + +static inline void numaq_setup_apic_routing(void) +{ + printk("Enabling APIC mode: %s. Using %d I/O APICs\n", + "NUMA-Q", nr_ioapics); +} + +/* + * Skip adding the timer int on secondary nodes, which causes + * a small but painful rift in the time-space continuum. + */ +static inline int numaq_multi_timer_check(int apic, int irq) +{ + return apic != 0 && irq == 0; +} + +static inline physid_mask_t numaq_ioapic_phys_id_map(physid_mask_t phys_map) +{ + /* We don't have a good way to do this yet - hack */ + return physids_promote(0xFUL); +} + +/* Mapping from cpu number to logical apicid */ +extern u8 cpu_2_logical_apicid[]; + +static inline int numaq_cpu_to_logical_apicid(int cpu) +{ + if (cpu >= nr_cpu_ids) + return BAD_APICID; + return (int)cpu_2_logical_apicid[cpu]; +} + +/* + * Supporting over 60 cpus on NUMA-Q requires a locality-dependent + * cpu to APIC ID relation to properly interact with the intelligent + * mode of the cluster controller. + */ +static inline int numaq_cpu_present_to_apicid(int mps_cpu) +{ + if (mps_cpu < 60) + return ((mps_cpu >> 2) << 4) | (1 << (mps_cpu & 0x3)); + else + return BAD_APICID; +} + +static inline int numaq_apicid_to_node(int logical_apicid) +{ + return logical_apicid >> 4; +} + +static inline physid_mask_t numaq_apicid_to_cpu_present(int logical_apicid) +{ + int node = numaq_apicid_to_node(logical_apicid); + int cpu = __ffs(logical_apicid & 0xf); + + return physid_mask_of_physid(cpu + 4*node); +} + +/* Where the IO area was mapped on multiquad, always 0 otherwise */ +void *xquad_portio; + +static inline int numaq_check_phys_apicid_present(int boot_cpu_physical_apicid) +{ + return 1; +} + +/* + * We use physical apicids here, not logical, so just return the default + * physical broadcast to stop people from breaking us + */ +static inline unsigned int numaq_cpu_mask_to_apicid(const cpumask_t *cpumask) +{ + return 0x0F; +} + +static inline unsigned int +numaq_cpu_mask_to_apicid_and(const struct cpumask *cpumask, + const struct cpumask *andmask) +{ + return 0x0F; +} + +/* No NUMA-Q box has a HT CPU, but it can't hurt to use the default code. */ +static inline int numaq_phys_pkg_id(int cpuid_apic, int index_msb) +{ + return cpuid_apic >> index_msb; +} +static int __numaq_mps_oem_check(struct mpc_table *mpc, char *oem, char *productid) +{ + numaq_mps_oem_check(mpc, oem, productid); + return found_numaq; +} + +static int probe_numaq(void) +{ + /* already know from get_memcfg_numaq() */ + return found_numaq; +} + +static void numaq_vector_allocation_domain(int cpu, cpumask_t *retmask) +{ + /* Careful. Some cpus do not strictly honor the set of cpus + * specified in the interrupt destination when using lowest + * priority interrupt delivery mode. + * + * In particular there was a hyperthreading cpu observed to + * deliver interrupts to the wrong hyperthread when only one + * hyperthread was specified in the interrupt desitination. + */ + *retmask = (cpumask_t){ { [0] = APIC_ALL_CPUS, } }; +} + +static void numaq_setup_portio_remap(void) +{ + int num_quads = num_online_nodes(); + + if (num_quads <= 1) + return; + + printk("Remapping cross-quad port I/O for %d quads\n", num_quads); + xquad_portio = ioremap(XQUAD_PORTIO_BASE, num_quads*XQUAD_PORTIO_QUAD); + printk("xquad_portio vaddr 0x%08lx, len %08lx\n", + (u_long) xquad_portio, (u_long) num_quads*XQUAD_PORTIO_QUAD); +} + +struct genapic apic_numaq = { + + .name = "NUMAQ", + .probe = probe_numaq, + .acpi_madt_oem_check = NULL, + .apic_id_registered = numaq_apic_id_registered, + + .irq_delivery_mode = dest_LowestPrio, + /* physical delivery on LOCAL quad: */ + .irq_dest_mode = 0, + + .target_cpus = numaq_target_cpus, + .disable_esr = 1, + .dest_logical = APIC_DEST_LOGICAL, + .check_apicid_used = numaq_check_apicid_used, + .check_apicid_present = numaq_check_apicid_present, + + .vector_allocation_domain = numaq_vector_allocation_domain, + .init_apic_ldr = numaq_init_apic_ldr, + + .ioapic_phys_id_map = numaq_ioapic_phys_id_map, + .setup_apic_routing = numaq_setup_apic_routing, + .multi_timer_check = numaq_multi_timer_check, + .apicid_to_node = numaq_apicid_to_node, + .cpu_to_logical_apicid = numaq_cpu_to_logical_apicid, + .cpu_present_to_apicid = numaq_cpu_present_to_apicid, + .apicid_to_cpu_present = numaq_apicid_to_cpu_present, + .setup_portio_remap = numaq_setup_portio_remap, + .check_phys_apicid_present = numaq_check_phys_apicid_present, + .enable_apic_mode = NULL, + .phys_pkg_id = numaq_phys_pkg_id, + .mps_oem_check = __numaq_mps_oem_check, + + .get_apic_id = numaq_get_apic_id, + .set_apic_id = NULL, + .apic_id_mask = 0x0F << 24, + + .cpu_mask_to_apicid = numaq_cpu_mask_to_apicid, + .cpu_mask_to_apicid_and = numaq_cpu_mask_to_apicid_and, + + .send_IPI_mask = numaq_send_IPI_mask, + .send_IPI_mask_allbutself = NULL, + .send_IPI_allbutself = numaq_send_IPI_allbutself, + .send_IPI_all = numaq_send_IPI_all, + .send_IPI_self = default_send_IPI_self, + + .wakeup_cpu = NULL, + .trampoline_phys_low = NUMAQ_TRAMPOLINE_PHYS_LOW, + .trampoline_phys_high = NUMAQ_TRAMPOLINE_PHYS_HIGH, + + /* We don't do anything here because we use NMI's to boot instead */ + .wait_for_init_deassert = NULL, + + .smp_callin_clear_local_apic = numaq_smp_callin_clear_local_apic, + .store_NMI_vector = numaq_store_NMI_vector, + .inquire_remote_apic = NULL, +}; |