diff options
Diffstat (limited to 'arch/x86/kernel/nmi_32.c')
| -rw-r--r-- | arch/x86/kernel/nmi_32.c | 467 |
1 files changed, 0 insertions, 467 deletions
diff --git a/arch/x86/kernel/nmi_32.c b/arch/x86/kernel/nmi_32.c deleted file mode 100644 index 84160f7..0000000 --- a/arch/x86/kernel/nmi_32.c +++ /dev/null @@ -1,467 +0,0 @@ -/* - * NMI watchdog support on APIC systems - * - * Started by Ingo Molnar <mingo@redhat.com> - * - * Fixes: - * Mikael Pettersson : AMD K7 support for local APIC NMI watchdog. - * Mikael Pettersson : Power Management for local APIC NMI watchdog. - * Mikael Pettersson : Pentium 4 support for local APIC NMI watchdog. - * Pavel Machek and - * Mikael Pettersson : PM converted to driver model. Disable/enable API. - */ - -#include <linux/delay.h> -#include <linux/interrupt.h> -#include <linux/module.h> -#include <linux/nmi.h> -#include <linux/sysdev.h> -#include <linux/sysctl.h> -#include <linux/percpu.h> -#include <linux/kprobes.h> -#include <linux/cpumask.h> -#include <linux/kernel_stat.h> -#include <linux/kdebug.h> -#include <linux/slab.h> - -#include <asm/smp.h> -#include <asm/nmi.h> - -#include "mach_traps.h" - -int unknown_nmi_panic; -int nmi_watchdog_enabled; - -static cpumask_t backtrace_mask = CPU_MASK_NONE; - -/* nmi_active: - * >0: the lapic NMI watchdog is active, but can be disabled - * <0: the lapic NMI watchdog has not been set up, and cannot - * be enabled - * 0: the lapic NMI watchdog is disabled, but can be enabled - */ -atomic_t nmi_active = ATOMIC_INIT(0); /* oprofile uses this */ - -unsigned int nmi_watchdog = NMI_DEFAULT; -static unsigned int nmi_hz = HZ; - -static DEFINE_PER_CPU(short, wd_enabled); - -static int endflag __initdata = 0; - -#ifdef CONFIG_SMP -/* The performance counters used by NMI_LOCAL_APIC don't trigger when - * the CPU is idle. To make sure the NMI watchdog really ticks on all - * CPUs during the test make them busy. - */ -static __init void nmi_cpu_busy(void *data) -{ - local_irq_enable_in_hardirq(); - /* Intentionally don't use cpu_relax here. This is - to make sure that the performance counter really ticks, - even if there is a simulator or similar that catches the - pause instruction. On a real HT machine this is fine because - all other CPUs are busy with "useless" delay loops and don't - care if they get somewhat less cycles. */ - while (endflag == 0) - mb(); -} -#endif - -int __init check_nmi_watchdog(void) -{ - unsigned int *prev_nmi_count; - int cpu; - - if ((nmi_watchdog == NMI_NONE) || (nmi_watchdog == NMI_DISABLED)) - return 0; - - if (!atomic_read(&nmi_active)) - return 0; - - prev_nmi_count = kmalloc(NR_CPUS * sizeof(int), GFP_KERNEL); - if (!prev_nmi_count) - return -1; - - printk(KERN_INFO "Testing NMI watchdog ... "); - -#ifdef CONFIG_SMP - if (nmi_watchdog == NMI_LOCAL_APIC) - smp_call_function(nmi_cpu_busy, (void *)&endflag, 0, 0); -#endif - - for_each_possible_cpu(cpu) - prev_nmi_count[cpu] = nmi_count(cpu); - local_irq_enable(); - mdelay((20*1000)/nmi_hz); // wait 20 ticks - - for_each_possible_cpu(cpu) { -#ifdef CONFIG_SMP - /* Check cpu_callin_map here because that is set - after the timer is started. */ - if (!cpu_isset(cpu, cpu_callin_map)) - continue; -#endif - if (!per_cpu(wd_enabled, cpu)) - continue; - if (nmi_count(cpu) - prev_nmi_count[cpu] <= 5) { - printk(KERN_WARNING "WARNING: CPU#%d: NMI " - "appears to be stuck (%d->%d)!\n", - cpu, - prev_nmi_count[cpu], - nmi_count(cpu)); - per_cpu(wd_enabled, cpu) = 0; - atomic_dec(&nmi_active); - } - } - endflag = 1; - if (!atomic_read(&nmi_active)) { - kfree(prev_nmi_count); - atomic_set(&nmi_active, -1); - return -1; - } - printk("OK.\n"); - - /* now that we know it works we can reduce NMI frequency to - something more reasonable; makes a difference in some configs */ - if (nmi_watchdog == NMI_LOCAL_APIC) - nmi_hz = lapic_adjust_nmi_hz(1); - - kfree(prev_nmi_count); - return 0; -} - -static int __init setup_nmi_watchdog(char *str) -{ - int nmi; - - get_option(&str, &nmi); - - if ((nmi >= NMI_INVALID) || (nmi < NMI_NONE)) - return 0; - - nmi_watchdog = nmi; - return 1; -} - -__setup("nmi_watchdog=", setup_nmi_watchdog); - - -/* Suspend/resume support */ - -#ifdef CONFIG_PM - -static int nmi_pm_active; /* nmi_active before suspend */ - -static int lapic_nmi_suspend(struct sys_device *dev, pm_message_t state) -{ - /* only CPU0 goes here, other CPUs should be offline */ - nmi_pm_active = atomic_read(&nmi_active); - stop_apic_nmi_watchdog(NULL); - BUG_ON(atomic_read(&nmi_active) != 0); - return 0; -} - -static int lapic_nmi_resume(struct sys_device *dev) -{ - /* only CPU0 goes here, other CPUs should be offline */ - if (nmi_pm_active > 0) { - setup_apic_nmi_watchdog(NULL); - touch_nmi_watchdog(); - } - return 0; -} - - -static struct sysdev_class nmi_sysclass = { - .name = "lapic_nmi", - .resume = lapic_nmi_resume, - .suspend = lapic_nmi_suspend, -}; - -static struct sys_device device_lapic_nmi = { - .id = 0, - .cls = &nmi_sysclass, -}; - -static int __init init_lapic_nmi_sysfs(void) -{ - int error; - - /* should really be a BUG_ON but b/c this is an - * init call, it just doesn't work. -dcz - */ - if (nmi_watchdog != NMI_LOCAL_APIC) - return 0; - - if (atomic_read(&nmi_active) < 0) - return 0; - - error = sysdev_class_register(&nmi_sysclass); - if (!error) - error = sysdev_register(&device_lapic_nmi); - return error; -} -/* must come after the local APIC's device_initcall() */ -late_initcall(init_lapic_nmi_sysfs); - -#endif /* CONFIG_PM */ - -static void __acpi_nmi_enable(void *__unused) -{ - apic_write_around(APIC_LVT0, APIC_DM_NMI); -} - -/* - * Enable timer based NMIs on all CPUs: - */ -void acpi_nmi_enable(void) -{ - if (atomic_read(&nmi_active) && nmi_watchdog == NMI_IO_APIC) - on_each_cpu(__acpi_nmi_enable, NULL, 0, 1); -} - -static void __acpi_nmi_disable(void *__unused) -{ - apic_write(APIC_LVT0, APIC_DM_NMI | APIC_LVT_MASKED); -} - -/* - * Disable timer based NMIs on all CPUs: - */ -void acpi_nmi_disable(void) -{ - if (atomic_read(&nmi_active) && nmi_watchdog == NMI_IO_APIC) - on_each_cpu(__acpi_nmi_disable, NULL, 0, 1); -} - -void setup_apic_nmi_watchdog(void *unused) -{ - if (__get_cpu_var(wd_enabled)) - return; - - /* cheap hack to support suspend/resume */ - /* if cpu0 is not active neither should the other cpus */ - if ((smp_processor_id() != 0) && (atomic_read(&nmi_active) <= 0)) - return; - - switch (nmi_watchdog) { - case NMI_LOCAL_APIC: - __get_cpu_var(wd_enabled) = 1; /* enable it before to avoid race with handler */ - if (lapic_watchdog_init(nmi_hz) < 0) { - __get_cpu_var(wd_enabled) = 0; - return; - } - /* FALL THROUGH */ - case NMI_IO_APIC: - __get_cpu_var(wd_enabled) = 1; - atomic_inc(&nmi_active); - } -} - -void stop_apic_nmi_watchdog(void *unused) -{ - /* only support LOCAL and IO APICs for now */ - if ((nmi_watchdog != NMI_LOCAL_APIC) && - (nmi_watchdog != NMI_IO_APIC)) - return; - if (__get_cpu_var(wd_enabled) == 0) - return; - if (nmi_watchdog == NMI_LOCAL_APIC) - lapic_watchdog_stop(); - __get_cpu_var(wd_enabled) = 0; - atomic_dec(&nmi_active); -} - -/* - * the best way to detect whether a CPU has a 'hard lockup' problem - * is to check it's local APIC timer IRQ counts. If they are not - * changing then that CPU has some problem. - * - * as these watchdog NMI IRQs are generated on every CPU, we only - * have to check the current processor. - * - * since NMIs don't listen to _any_ locks, we have to be extremely - * careful not to rely on unsafe variables. The printk might lock - * up though, so we have to break up any console locks first ... - * [when there will be more tty-related locks, break them up - * here too!] - */ - -static unsigned int - last_irq_sums [NR_CPUS], - alert_counter [NR_CPUS]; - -void touch_nmi_watchdog(void) -{ - if (nmi_watchdog > 0) { - unsigned cpu; - - /* - * Just reset the alert counters, (other CPUs might be - * spinning on locks we hold): - */ - for_each_present_cpu(cpu) { - if (alert_counter[cpu]) - alert_counter[cpu] = 0; - } - } - - /* - * Tickle the softlockup detector too: - */ - touch_softlockup_watchdog(); -} -EXPORT_SYMBOL(touch_nmi_watchdog); - -extern void die_nmi(struct pt_regs *, const char *msg); - -notrace __kprobes int -nmi_watchdog_tick(struct pt_regs *regs, unsigned reason) -{ - - /* - * Since current_thread_info()-> is always on the stack, and we - * always switch the stack NMI-atomically, it's safe to use - * smp_processor_id(). - */ - unsigned int sum; - int touched = 0; - int cpu = smp_processor_id(); - int rc = 0; - - /* check for other users first */ - if (notify_die(DIE_NMI, "nmi", regs, reason, 2, SIGINT) - == NOTIFY_STOP) { - rc = 1; - touched = 1; - } - - if (cpu_isset(cpu, backtrace_mask)) { - static DEFINE_SPINLOCK(lock); /* Serialise the printks */ - - spin_lock(&lock); - printk("NMI backtrace for cpu %d\n", cpu); - dump_stack(); - spin_unlock(&lock); - cpu_clear(cpu, backtrace_mask); - } - - /* - * Take the local apic timer and PIT/HPET into account. We don't - * know which one is active, when we have highres/dyntick on - */ - sum = per_cpu(irq_stat, cpu).apic_timer_irqs + - per_cpu(irq_stat, cpu).irq0_irqs; - - /* if the none of the timers isn't firing, this cpu isn't doing much */ - if (!touched && last_irq_sums[cpu] == sum) { - /* - * Ayiee, looks like this CPU is stuck ... - * wait a few IRQs (5 seconds) before doing the oops ... - */ - alert_counter[cpu]++; - if (alert_counter[cpu] == 5*nmi_hz) - /* - * die_nmi will return ONLY if NOTIFY_STOP happens.. - */ - die_nmi(regs, "BUG: NMI Watchdog detected LOCKUP"); - } else { - last_irq_sums[cpu] = sum; - alert_counter[cpu] = 0; - } - /* see if the nmi watchdog went off */ - if (!__get_cpu_var(wd_enabled)) - return rc; - switch (nmi_watchdog) { - case NMI_LOCAL_APIC: - rc |= lapic_wd_event(nmi_hz); - break; - case NMI_IO_APIC: - /* don't know how to accurately check for this. - * just assume it was a watchdog timer interrupt - * This matches the old behaviour. - */ - rc = 1; - break; - } - return rc; -} - -#ifdef CONFIG_SYSCTL - -static int unknown_nmi_panic_callback(struct pt_regs *regs, int cpu) -{ - unsigned char reason = get_nmi_reason(); - char buf[64]; - - sprintf(buf, "NMI received for unknown reason %02x\n", reason); - die_nmi(regs, buf); - return 0; -} - -/* - * proc handler for /proc/sys/kernel/nmi - */ -int proc_nmi_enabled(struct ctl_table *table, int write, struct file *file, - void __user *buffer, size_t *length, loff_t *ppos) -{ - int old_state; - - nmi_watchdog_enabled = (atomic_read(&nmi_active) > 0) ? 1 : 0; - old_state = nmi_watchdog_enabled; - proc_dointvec(table, write, file, buffer, length, ppos); - if (!!old_state == !!nmi_watchdog_enabled) - return 0; - - if (atomic_read(&nmi_active) < 0 || nmi_watchdog == NMI_DISABLED) { - printk( KERN_WARNING "NMI watchdog is permanently disabled\n"); - return -EIO; - } - - if (nmi_watchdog == NMI_DEFAULT) { - if (lapic_watchdog_ok()) - nmi_watchdog = NMI_LOCAL_APIC; - else - nmi_watchdog = NMI_IO_APIC; - } - - if (nmi_watchdog == NMI_LOCAL_APIC) { - if (nmi_watchdog_enabled) - enable_lapic_nmi_watchdog(); - else - disable_lapic_nmi_watchdog(); - } else { - printk( KERN_WARNING - "NMI watchdog doesn't know what hardware to touch\n"); - return -EIO; - } - return 0; -} - -#endif - -int do_nmi_callback(struct pt_regs *regs, int cpu) -{ -#ifdef CONFIG_SYSCTL - if (unknown_nmi_panic) - return unknown_nmi_panic_callback(regs, cpu); -#endif - return 0; -} - -void __trigger_all_cpu_backtrace(void) -{ - int i; - - backtrace_mask = cpu_online_map; - /* Wait for up to 10 seconds for all CPUs to do the backtrace */ - for (i = 0; i < 10 * 1000; i++) { - if (cpus_empty(backtrace_mask)) - break; - mdelay(1); - } -} - -EXPORT_SYMBOL(nmi_active); -EXPORT_SYMBOL(nmi_watchdog); |
