summaryrefslogtreecommitdiffstats
path: root/arch/ppc/kernel/head.S
diff options
context:
space:
mode:
Diffstat (limited to 'arch/ppc/kernel/head.S')
-rw-r--r--arch/ppc/kernel/head.S117
1 files changed, 4 insertions, 113 deletions
diff --git a/arch/ppc/kernel/head.S b/arch/ppc/kernel/head.S
index c7cb9d5..1b0ec72 100644
--- a/arch/ppc/kernel/head.S
+++ b/arch/ppc/kernel/head.S
@@ -32,10 +32,6 @@
#include <asm/ppc_asm.h>
#include <asm/asm-offsets.h>
-#ifdef CONFIG_APUS
-#include <asm/amigappc.h>
-#endif
-
/* 601 only have IBAT; cr0.eq is set on 601 when using this macro */
#define LOAD_BAT(n, reg, RA, RB) \
/* see the comment for clear_bats() -- Cort */ \
@@ -128,14 +124,6 @@ __start:
*/
bl early_init
-#ifdef CONFIG_APUS
-/* On APUS the __va/__pa constants need to be set to the correct
- * values before continuing.
- */
- mr r4,r30
- bl fix_mem_constants
-#endif /* CONFIG_APUS */
-
/* Switch MMU off, clear BATs and flush TLB. At this point, r3 contains
* the physical address we are running at, returned by early_init()
*/
@@ -145,7 +133,7 @@ __after_mmu_off:
bl flush_tlbs
bl initial_bats
-#if !defined(CONFIG_APUS) && defined(CONFIG_BOOTX_TEXT)
+#ifdef CONFIG_BOOTX_TEXT
bl setup_disp_bat
#endif
@@ -161,7 +149,6 @@ __after_mmu_off:
#endif /* CONFIG_6xx */
-#ifndef CONFIG_APUS
/*
* We need to run with _start at physical address 0.
* If the MMU is already turned on, we copy stuff to KERNELBASE,
@@ -172,7 +159,7 @@ __after_mmu_off:
addis r4,r3,KERNELBASE@h /* current address of _start */
cmpwi 0,r4,0 /* are we already running at 0? */
bne relocate_kernel
-#endif /* CONFIG_APUS */
+
/*
* we now have the 1st 16M of ram mapped with the bats.
* prep needs the mmu to be turned on here, but pmac already has it on.
@@ -812,85 +799,6 @@ copy_and_flush:
addi r6,r6,4
blr
-#ifdef CONFIG_APUS
-/*
- * On APUS the physical base address of the kernel is not known at compile
- * time, which means the __pa/__va constants used are incorrect. In the
- * __init section is recorded the virtual addresses of instructions using
- * these constants, so all that has to be done is fix these before
- * continuing the kernel boot.
- *
- * r4 = The physical address of the kernel base.
- */
-fix_mem_constants:
- mr r10,r4
- addis r10,r10,-KERNELBASE@h /* virt_to_phys constant */
- neg r11,r10 /* phys_to_virt constant */
-
- lis r12,__vtop_table_begin@h
- ori r12,r12,__vtop_table_begin@l
- add r12,r12,r10 /* table begin phys address */
- lis r13,__vtop_table_end@h
- ori r13,r13,__vtop_table_end@l
- add r13,r13,r10 /* table end phys address */
- subi r12,r12,4
- subi r13,r13,4
-1: lwzu r14,4(r12) /* virt address of instruction */
- add r14,r14,r10 /* phys address of instruction */
- lwz r15,0(r14) /* instruction, now insert top */
- rlwimi r15,r10,16,16,31 /* half of vp const in low half */
- stw r15,0(r14) /* of instruction and restore. */
- dcbst r0,r14 /* write it to memory */
- sync
- icbi r0,r14 /* flush the icache line */
- cmpw r12,r13
- bne 1b
- sync /* additional sync needed on g4 */
- isync
-
-/*
- * Map the memory where the exception handlers will
- * be copied to when hash constants have been patched.
- */
-#ifdef CONFIG_APUS_FAST_EXCEPT
- lis r8,0xfff0
-#else
- lis r8,0
-#endif
- ori r8,r8,0x2 /* 128KB, supervisor */
- mtspr SPRN_DBAT3U,r8
- mtspr SPRN_DBAT3L,r8
-
- lis r12,__ptov_table_begin@h
- ori r12,r12,__ptov_table_begin@l
- add r12,r12,r10 /* table begin phys address */
- lis r13,__ptov_table_end@h
- ori r13,r13,__ptov_table_end@l
- add r13,r13,r10 /* table end phys address */
- subi r12,r12,4
- subi r13,r13,4
-1: lwzu r14,4(r12) /* virt address of instruction */
- add r14,r14,r10 /* phys address of instruction */
- lwz r15,0(r14) /* instruction, now insert top */
- rlwimi r15,r11,16,16,31 /* half of pv const in low half*/
- stw r15,0(r14) /* of instruction and restore. */
- dcbst r0,r14 /* write it to memory */
- sync
- icbi r0,r14 /* flush the icache line */
- cmpw r12,r13
- bne 1b
-
- sync /* additional sync needed on g4 */
- isync /* No speculative loading until now */
- blr
-
-/***********************************************************************
- * Please note that on APUS the exception handlers are located at the
- * physical address 0xfff0000. For this reason, the exception handlers
- * cannot use relative branches to access the code below.
- ***********************************************************************/
-#endif /* CONFIG_APUS */
-
#ifdef CONFIG_SMP
.globl __secondary_start_pmac_0
__secondary_start_pmac_0:
@@ -1043,19 +951,6 @@ start_here:
bl machine_init
bl MMU_init
-#ifdef CONFIG_APUS
- /* Copy exception code to exception vector base on APUS. */
- lis r4,KERNELBASE@h
-#ifdef CONFIG_APUS_FAST_EXCEPT
- lis r3,0xfff0 /* Copy to 0xfff00000 */
-#else
- lis r3,0 /* Copy to 0x00000000 */
-#endif
- li r5,0x4000 /* # bytes of memory to copy */
- li r6,0
- bl copy_and_flush /* copy the first 0x4000 bytes */
-#endif /* CONFIG_APUS */
-
/*
* Go back to running unmapped so we can load up new values
* for SDR1 (hash table pointer) and the segment registers
@@ -1232,11 +1127,7 @@ initial_bats:
#else
ori r8,r8,2 /* R/W access */
#endif /* CONFIG_SMP */
-#ifdef CONFIG_APUS
- ori r11,r11,BL_8M<<2|0x2 /* set up 8MB BAT registers for 604 */
-#else
ori r11,r11,BL_256M<<2|0x2 /* set up BAT registers for 604 */
-#endif /* CONFIG_APUS */
mtspr SPRN_DBAT0L,r8 /* N.B. 6xx (not 601) have valid */
mtspr SPRN_DBAT0U,r11 /* bit in upper BAT register */
@@ -1245,7 +1136,7 @@ initial_bats:
isync
blr
-#if !defined(CONFIG_APUS) && defined(CONFIG_BOOTX_TEXT)
+#ifdef CONFIG_BOOTX_TEXT
setup_disp_bat:
/*
* setup the display bat prepared for us in prom.c
@@ -1268,7 +1159,7 @@ setup_disp_bat:
mtspr SPRN_IBAT3U,r11
blr
-#endif /* !defined(CONFIG_APUS) && defined(CONFIG_BOOTX_TEXT) */
+#endif /* defined(CONFIG_BOOTX_TEXT) */
#ifdef CONFIG_8260
/* Jump into the system reset for the rom.
OpenPOWER on IntegriCloud