diff options
Diffstat (limited to 'arch/ppc/boot/simple/m8260_tty.c')
| -rw-r--r-- | arch/ppc/boot/simple/m8260_tty.c | 325 |
1 files changed, 0 insertions, 325 deletions
diff --git a/arch/ppc/boot/simple/m8260_tty.c b/arch/ppc/boot/simple/m8260_tty.c deleted file mode 100644 index d770947..0000000 --- a/arch/ppc/boot/simple/m8260_tty.c +++ /dev/null @@ -1,325 +0,0 @@ -/* Minimal serial functions needed to send messages out the serial - * port on SMC1. - */ -#include <linux/types.h> -#include <asm/mpc8260.h> -#include <asm/cpm2.h> -#include <asm/immap_cpm2.h> - -uint no_print; -extern char *params[]; -extern int nparams; -static u_char cons_hold[128], *sgptr; -static int cons_hold_cnt; - -/* If defined, enables serial console. The value (1 through 4) - * should designate which SCC is used, but this isn't complete. Only - * SCC1 is known to work at this time. - * We're only linked if SERIAL_CPM_CONSOLE=y, so we only need to test - * SERIAL_CPM_SCC1. - */ -#ifdef CONFIG_SERIAL_CPM_SCC1 -#define SCC_CONSOLE 1 -#endif - -unsigned long -serial_init(int ignored, bd_t *bd) -{ -#ifdef SCC_CONSOLE - volatile scc_t *sccp; - volatile scc_uart_t *sup; -#else - volatile smc_t *sp; - volatile smc_uart_t *up; -#endif - volatile cbd_t *tbdf, *rbdf; - volatile cpm2_map_t *ip; - volatile iop_cpm2_t *io; - volatile cpm_cpm2_t *cp; - uint dpaddr, memaddr; - - ip = (cpm2_map_t *)CPM_MAP_ADDR; - cp = &ip->im_cpm; - io = &ip->im_ioport; - - /* Perform a reset. - */ - cp->cp_cpcr = (CPM_CR_RST | CPM_CR_FLG); - - /* Wait for it. - */ - while (cp->cp_cpcr & CPM_CR_FLG); - -#ifdef CONFIG_ADS8260 - /* Enable the RS-232 transceivers. - */ - *(volatile uint *)(BCSR_ADDR + 4) &= - ~(BCSR1_RS232_EN1 | BCSR1_RS232_EN2); -#endif - -#ifdef SCC_CONSOLE - sccp = (scc_t *)&(ip->im_scc[SCC_CONSOLE-1]); - sup = (scc_uart_t *)&ip->im_dprambase[PROFF_SCC1 + ((SCC_CONSOLE-1) << 8)]; - sccp->scc_sccm &= ~(UART_SCCM_TX | UART_SCCM_RX); - sccp->scc_gsmrl &= ~(SCC_GSMRL_ENR | SCC_GSMRL_ENT); - - /* Use Port D for SCC1 instead of other functions. - */ - io->iop_ppard |= 0x00000003; - io->iop_psord &= ~0x00000001; /* Rx */ - io->iop_psord |= 0x00000002; /* Tx */ - io->iop_pdird &= ~0x00000001; /* Rx */ - io->iop_pdird |= 0x00000002; /* Tx */ - -#else - sp = (smc_t*)&(ip->im_smc[0]); - *(ushort *)(&ip->im_dprambase[PROFF_SMC1_BASE]) = PROFF_SMC1; - up = (smc_uart_t *)&ip->im_dprambase[PROFF_SMC1]; - - /* Disable transmitter/receiver. - */ - sp->smc_smcmr &= ~(SMCMR_REN | SMCMR_TEN); - - /* Use Port D for SMC1 instead of other functions. - */ - io->iop_ppard |= 0x00c00000; - io->iop_pdird |= 0x00400000; - io->iop_pdird &= ~0x00800000; - io->iop_psord &= ~0x00c00000; -#endif - - /* Allocate space for two buffer descriptors in the DP ram. - * For now, this address seems OK, but it may have to - * change with newer versions of the firmware. - */ - dpaddr = 0x0800; - - /* Grab a few bytes from the top of memory. - */ - memaddr = (bd->bi_memsize - 256) & ~15; - - /* Set the physical address of the host memory buffers in - * the buffer descriptors. - */ - rbdf = (cbd_t *)&ip->im_dprambase[dpaddr]; - rbdf->cbd_bufaddr = memaddr; - rbdf->cbd_sc = 0; - tbdf = rbdf + 1; - tbdf->cbd_bufaddr = memaddr+128; - tbdf->cbd_sc = 0; - - /* Set up the uart parameters in the parameter ram. - */ -#ifdef SCC_CONSOLE - sup->scc_genscc.scc_rbase = dpaddr; - sup->scc_genscc.scc_tbase = dpaddr + sizeof(cbd_t); - - /* Set up the uart parameters in the - * parameter ram. - */ - sup->scc_genscc.scc_rfcr = CPMFCR_GBL | CPMFCR_EB; - sup->scc_genscc.scc_tfcr = CPMFCR_GBL | CPMFCR_EB; - - sup->scc_genscc.scc_mrblr = 128; - sup->scc_maxidl = 8; - sup->scc_brkcr = 1; - sup->scc_parec = 0; - sup->scc_frmec = 0; - sup->scc_nosec = 0; - sup->scc_brkec = 0; - sup->scc_uaddr1 = 0; - sup->scc_uaddr2 = 0; - sup->scc_toseq = 0; - sup->scc_char1 = 0x8000; - sup->scc_char2 = 0x8000; - sup->scc_char3 = 0x8000; - sup->scc_char4 = 0x8000; - sup->scc_char5 = 0x8000; - sup->scc_char6 = 0x8000; - sup->scc_char7 = 0x8000; - sup->scc_char8 = 0x8000; - sup->scc_rccm = 0xc0ff; - - /* Send the CPM an initialize command. - */ - cp->cp_cpcr = mk_cr_cmd(CPM_CR_SCC1_PAGE, CPM_CR_SCC1_SBLOCK, 0, - CPM_CR_INIT_TRX) | CPM_CR_FLG; - while (cp->cp_cpcr & CPM_CR_FLG); - - /* Set UART mode, 8 bit, no parity, one stop. - * Enable receive and transmit. - */ - sccp->scc_gsmrh = 0; - sccp->scc_gsmrl = - (SCC_GSMRL_MODE_UART | SCC_GSMRL_TDCR_16 | SCC_GSMRL_RDCR_16); - - /* Disable all interrupts and clear all pending - * events. - */ - sccp->scc_sccm = 0; - sccp->scc_scce = 0xffff; - sccp->scc_dsr = 0x7e7e; - sccp->scc_psmr = 0x3000; - - /* Wire BRG1 to SCC1. The console driver will take care of - * others. - */ - ip->im_cpmux.cmx_scr = 0; -#else - up->smc_rbase = dpaddr; - up->smc_tbase = dpaddr+sizeof(cbd_t); - up->smc_rfcr = CPMFCR_EB; - up->smc_tfcr = CPMFCR_EB; - up->smc_brklen = 0; - up->smc_brkec = 0; - up->smc_brkcr = 0; - up->smc_mrblr = 128; - up->smc_maxidl = 8; - - /* Set UART mode, 8 bit, no parity, one stop. - * Enable receive and transmit. - */ - sp->smc_smcmr = smcr_mk_clen(9) | SMCMR_SM_UART; - - /* Mask all interrupts and remove anything pending. - */ - sp->smc_smcm = 0; - sp->smc_smce = 0xff; - - /* Set up the baud rate generator. - */ - ip->im_cpmux.cmx_smr = 0; -#endif - - /* The baud rate divisor needs to be coordinated with clk_8260(). - */ - ip->im_brgc1 = - (((bd->bi_brgfreq/16) / bd->bi_baudrate) << 1) | - CPM_BRG_EN; - - /* Make the first buffer the only buffer. - */ - tbdf->cbd_sc |= BD_SC_WRAP; - rbdf->cbd_sc |= BD_SC_EMPTY | BD_SC_WRAP; - - /* Initialize Tx/Rx parameters. - */ -#ifdef SCC_CONSOLE - sccp->scc_gsmrl |= (SCC_GSMRL_ENR | SCC_GSMRL_ENT); -#else - cp->cp_cpcr = mk_cr_cmd(CPM_CR_SMC1_PAGE, CPM_CR_SMC1_SBLOCK, 0, CPM_CR_INIT_TRX) | CPM_CR_FLG; - while (cp->cp_cpcr & CPM_CR_FLG); - - /* Enable transmitter/receiver. - */ - sp->smc_smcmr |= SMCMR_REN | SMCMR_TEN; -#endif - - /* This is ignored. - */ - return 0; -} - -int -serial_readbuf(u_char *cbuf) -{ - volatile cbd_t *rbdf; - volatile char *buf; -#ifdef SCC_CONSOLE - volatile scc_uart_t *sup; -#else - volatile smc_uart_t *up; -#endif - volatile cpm2_map_t *ip; - int i, nc; - - ip = (cpm2_map_t *)CPM_MAP_ADDR; - -#ifdef SCC_CONSOLE - sup = (scc_uart_t *)&ip->im_dprambase[PROFF_SCC1 + ((SCC_CONSOLE-1) << 8)]; - rbdf = (cbd_t *)&ip->im_dprambase[sup->scc_genscc.scc_rbase]; -#else - up = (smc_uart_t *)&(ip->im_dprambase[PROFF_SMC1]); - rbdf = (cbd_t *)&ip->im_dprambase[up->smc_rbase]; -#endif - - /* Wait for character to show up. - */ - buf = (char *)rbdf->cbd_bufaddr; - while (rbdf->cbd_sc & BD_SC_EMPTY); - nc = rbdf->cbd_datlen; - for (i=0; i<nc; i++) - *cbuf++ = *buf++; - rbdf->cbd_sc |= BD_SC_EMPTY; - - return(nc); -} - -void -serial_putc(void *ignored, const char c) -{ - volatile cbd_t *tbdf; - volatile char *buf; -#ifdef SCC_CONSOLE - volatile scc_uart_t *sup; -#else - volatile smc_uart_t *up; -#endif - volatile cpm2_map_t *ip; - - ip = (cpm2_map_t *)CPM_MAP_ADDR; -#ifdef SCC_CONSOLE - sup = (scc_uart_t *)&ip->im_dprambase[PROFF_SCC1 + ((SCC_CONSOLE-1) << 8)]; - tbdf = (cbd_t *)&ip->im_dprambase[sup->scc_genscc.scc_tbase]; -#else - up = (smc_uart_t *)&(ip->im_dprambase[PROFF_SMC1]); - tbdf = (cbd_t *)&ip->im_dprambase[up->smc_tbase]; -#endif - - /* Wait for last character to go. - */ - buf = (char *)tbdf->cbd_bufaddr; - while (tbdf->cbd_sc & BD_SC_READY); - - *buf = c; - tbdf->cbd_datlen = 1; - tbdf->cbd_sc |= BD_SC_READY; -} - -char -serial_getc(void *ignored) -{ - char c; - - if (cons_hold_cnt <= 0) { - cons_hold_cnt = serial_readbuf(cons_hold); - sgptr = cons_hold; - } - c = *sgptr++; - cons_hold_cnt--; - - return(c); -} - -int -serial_tstc(void *ignored) -{ - volatile cbd_t *rbdf; -#ifdef SCC_CONSOLE - volatile scc_uart_t *sup; -#else - volatile smc_uart_t *up; -#endif - volatile cpm2_map_t *ip; - - ip = (cpm2_map_t *)CPM_MAP_ADDR; -#ifdef SCC_CONSOLE - sup = (scc_uart_t *)&ip->im_dprambase[PROFF_SCC1 + ((SCC_CONSOLE-1) << 8)]; - rbdf = (cbd_t *)&ip->im_dprambase[sup->scc_genscc.scc_rbase]; -#else - up = (smc_uart_t *)&(ip->im_dprambase[PROFF_SMC1]); - rbdf = (cbd_t *)&ip->im_dprambase[up->smc_rbase]; -#endif - - return(!(rbdf->cbd_sc & BD_SC_EMPTY)); -} |
