diff options
Diffstat (limited to 'arch/powerpc/platforms/apus/Kconfig')
| -rw-r--r-- | arch/powerpc/platforms/apus/Kconfig | 130 |
1 files changed, 0 insertions, 130 deletions
diff --git a/arch/powerpc/platforms/apus/Kconfig b/arch/powerpc/platforms/apus/Kconfig deleted file mode 100644 index 6bde3bf..0000000 --- a/arch/powerpc/platforms/apus/Kconfig +++ /dev/null @@ -1,130 +0,0 @@ - -config AMIGA - bool - depends on APUS - default y - help - This option enables support for the Amiga series of computers. - -config ZORRO - bool - depends on APUS - default y - help - This enables support for the Zorro bus in the Amiga. If you have - expansion cards in your Amiga that conform to the Amiga - AutoConfig(tm) specification, say Y, otherwise N. Note that even - expansion cards that do not fit in the Zorro slots but fit in e.g. - the CPU slot may fall in this category, so you have to say Y to let - Linux use these. - -config ABSTRACT_CONSOLE - bool - depends on APUS - default y - -config APUS_FAST_EXCEPT - bool - depends on APUS - default y - -config AMIGA_PCMCIA - bool "Amiga 1200/600 PCMCIA support" - depends on APUS && EXPERIMENTAL - help - Include support in the kernel for pcmcia on Amiga 1200 and Amiga - 600. If you intend to use pcmcia cards say Y; otherwise say N. - -config AMIGA_BUILTIN_SERIAL - tristate "Amiga builtin serial support" - depends on APUS - help - If you want to use your Amiga's built-in serial port in Linux, - answer Y. - - To compile this driver as a module, choose M here. - -config GVPIOEXT - tristate "GVP IO-Extender support" - depends on APUS - help - If you want to use a GVP IO-Extender serial card in Linux, say Y. - Otherwise, say N. - -config GVPIOEXT_LP - tristate "GVP IO-Extender parallel printer support" - depends on GVPIOEXT - help - Say Y to enable driving a printer from the parallel port on your - GVP IO-Extender card, N otherwise. - -config GVPIOEXT_PLIP - tristate "GVP IO-Extender PLIP support" - depends on GVPIOEXT - help - Say Y to enable doing IP over the parallel port on your GVP - IO-Extender card, N otherwise. - -config MULTIFACE_III_TTY - tristate "Multiface Card III serial support" - depends on APUS - help - If you want to use a Multiface III card's serial port in Linux, - answer Y. - - To compile this driver as a module, choose M here. - -config A2232 - tristate "Commodore A2232 serial support (EXPERIMENTAL)" - depends on EXPERIMENTAL && APUS - ---help--- - This option supports the 2232 7-port serial card shipped with the - Amiga 2000 and other Zorro-bus machines, dating from 1989. At - a max of 19,200 bps, the ports are served by a 6551 ACIA UART chip - each, plus a 8520 CIA, and a master 6502 CPU and buffer as well. The - ports were connected with 8 pin DIN connectors on the card bracket, - for which 8 pin to DB25 adapters were supplied. The card also had - jumpers internally to toggle various pinning configurations. - - This driver can be built as a module; but then "generic_serial" - will also be built as a module. This has to be loaded before - "ser_a2232". If you want to do this, answer M here. - -config WHIPPET_SERIAL - tristate "Hisoft Whippet PCMCIA serial support" - depends on AMIGA_PCMCIA - help - HiSoft has a web page at <http://www.hisoft.co.uk/>, but there - is no listing for the Whippet in their Amiga section. - -config APNE - tristate "PCMCIA NE2000 support" - depends on AMIGA_PCMCIA - help - If you have a PCMCIA NE2000 compatible adapter, say Y. Otherwise, - say N. - - To compile this driver as a module, choose M here: the - module will be called apne. - -config SERIAL_CONSOLE - bool "Support for serial port console" - depends on APUS && (AMIGA_BUILTIN_SERIAL=y || GVPIOEXT=y || MULTIFACE_III_TTY=y) - -config HEARTBEAT - bool "Use power LED as a heartbeat" - depends on APUS - help - Use the power-on LED on your machine as a load meter. The exact - behavior is platform-dependent, but normally the flash frequency is - a hyperbolic function of the 5-minute load average. - -config PROC_HARDWARE - bool "/proc/hardware support" - depends on APUS - -source "drivers/zorro/Kconfig" - -config PCI_PERMEDIA - bool "PCI for Permedia2" - depends on !4xx && !8xx && APUS |
