diff options
Diffstat (limited to 'arch/mips/sgi-ip22')
| -rw-r--r-- | arch/mips/sgi-ip22/Makefile | 2 | ||||
| -rw-r--r-- | arch/mips/sgi-ip22/ip22-int.c | 2 | ||||
| -rw-r--r-- | arch/mips/sgi-ip22/ip22-nvram.c | 24 | ||||
| -rw-r--r-- | arch/mips/sgi-ip22/ip22-time.c | 14 |
4 files changed, 20 insertions, 22 deletions
diff --git a/arch/mips/sgi-ip22/Makefile b/arch/mips/sgi-ip22/Makefile index 6aa4c0c..b6d6492 100644 --- a/arch/mips/sgi-ip22/Makefile +++ b/arch/mips/sgi-ip22/Makefile @@ -7,5 +7,3 @@ obj-y += ip22-mc.o ip22-hpc.o ip22-int.o ip22-berr.o \ ip22-time.o ip22-nvram.o ip22-reset.o ip22-setup.o obj-$(CONFIG_EISA) += ip22-eisa.o - -EXTRA_AFLAGS := $(CFLAGS) diff --git a/arch/mips/sgi-ip22/ip22-int.c b/arch/mips/sgi-ip22/ip22-int.c index b454924..1834832 100644 --- a/arch/mips/sgi-ip22/ip22-int.c +++ b/arch/mips/sgi-ip22/ip22-int.c @@ -237,7 +237,7 @@ extern void indy_8254timer_irq(void); asmlinkage void plat_irq_dispatch(void) { - unsigned int pending = read_c0_cause(); + unsigned int pending = read_c0_status() & read_c0_cause(); /* * First we check for r4k counter/timer IRQ. diff --git a/arch/mips/sgi-ip22/ip22-nvram.c b/arch/mips/sgi-ip22/ip22-nvram.c index fd29fd4..e19d60d 100644 --- a/arch/mips/sgi-ip22/ip22-nvram.c +++ b/arch/mips/sgi-ip22/ip22-nvram.c @@ -52,8 +52,7 @@ * national semiconductor nv ram chip the op code is 3 bits and * the address is 6/8 bits. */ -static inline void eeprom_cmd(volatile unsigned int *ctrl, unsigned cmd, - unsigned reg) +static inline void eeprom_cmd(unsigned int *ctrl, unsigned cmd, unsigned reg) { unsigned short ser_cmd; int i; @@ -61,33 +60,34 @@ static inline void eeprom_cmd(volatile unsigned int *ctrl, unsigned cmd, ser_cmd = cmd | (reg << (16 - BITS_IN_COMMAND)); for (i = 0; i < BITS_IN_COMMAND; i++) { if (ser_cmd & (1<<15)) /* if high order bit set */ - *ctrl |= EEPROM_DATO; + writel(readl(ctrl) | EEPROM_DATO, ctrl); else - *ctrl &= ~EEPROM_DATO; - *ctrl &= ~EEPROM_ECLK; - *ctrl |= EEPROM_ECLK; + writel(readl(ctrl) & ~EEPROM_DATO, ctrl); + writel(readl(ctrl) & ~EEPROM_ECLK, ctrl); + writel(readl(ctrl) | EEPROM_ECLK, ctrl); ser_cmd <<= 1; } - *ctrl &= ~EEPROM_DATO; /* see data sheet timing diagram */ + /* see data sheet timing diagram */ + writel(readl(ctrl) & ~EEPROM_DATO, ctrl); } -unsigned short ip22_eeprom_read(volatile unsigned int *ctrl, int reg) +unsigned short ip22_eeprom_read(unsigned int *ctrl, int reg) { unsigned short res = 0; int i; - *ctrl &= ~EEPROM_EPROT; + writel(readl(ctrl) & ~EEPROM_EPROT, ctrl); eeprom_cs_on(ctrl); eeprom_cmd(ctrl, EEPROM_READ, reg); /* clock the data ouf of serial mem */ for (i = 0; i < 16; i++) { - *ctrl &= ~EEPROM_ECLK; + writel(readl(ctrl) & ~EEPROM_ECLK, ctrl); delay(); - *ctrl |= EEPROM_ECLK; + writel(readl(ctrl) | EEPROM_ECLK, ctrl); delay(); res <<= 1; - if (*ctrl & EEPROM_DATI) + if (readl(ctrl) & EEPROM_DATI) res |= 1; } diff --git a/arch/mips/sgi-ip22/ip22-time.c b/arch/mips/sgi-ip22/ip22-time.c index 2055547..8e88a44 100644 --- a/arch/mips/sgi-ip22/ip22-time.c +++ b/arch/mips/sgi-ip22/ip22-time.c @@ -94,7 +94,7 @@ static int indy_rtc_set_time(unsigned long tim) static unsigned long dosample(void) { u32 ct0, ct1; - volatile u8 msb, lsb; + u8 msb, lsb; /* Start the counter. */ sgint->tcword = (SGINT_TCWORD_CNT2 | SGINT_TCWORD_CALL | @@ -107,21 +107,21 @@ static unsigned long dosample(void) /* Latch and spin until top byte of counter2 is zero */ do { - sgint->tcword = SGINT_TCWORD_CNT2 | SGINT_TCWORD_CLAT; - lsb = sgint->tcnt2; - msb = sgint->tcnt2; + writeb(SGINT_TCWORD_CNT2 | SGINT_TCWORD_CLAT, &sgint->tcword); + lsb = readb(&sgint->tcnt2); + msb = readb(&sgint->tcnt2); ct1 = read_c0_count(); } while (msb); /* Stop the counter. */ - sgint->tcword = (SGINT_TCWORD_CNT2 | SGINT_TCWORD_CALL | - SGINT_TCWORD_MSWST); + writeb(sgint->tcword, (SGINT_TCWORD_CNT2 | SGINT_TCWORD_CALL | + SGINT_TCWORD_MSWST)); /* * Return the difference, this is how far the r4k counter increments * for every 1/HZ seconds. We round off the nearest 1 MHz of master * clock (= 1000000 / HZ / 2). */ - /*return (ct1 - ct0 + (500000/HZ/2)) / (500000/HZ) * (500000/HZ);*/ + return (ct1 - ct0) / (500000/HZ) * (500000/HZ); } |
