diff options
Diffstat (limited to 'arch/mips/cavium-octeon/pci.c')
| -rw-r--r-- | arch/mips/cavium-octeon/pci.c | 568 |
1 files changed, 0 insertions, 568 deletions
diff --git a/arch/mips/cavium-octeon/pci.c b/arch/mips/cavium-octeon/pci.c deleted file mode 100644 index 67c0ff5..0000000 --- a/arch/mips/cavium-octeon/pci.c +++ /dev/null @@ -1,568 +0,0 @@ -/* - * This file is subject to the terms and conditions of the GNU General Public - * License. See the file "COPYING" in the main directory of this archive - * for more details. - * - * Copyright (C) 2005-2007 Cavium Networks - */ -#include <linux/kernel.h> -#include <linux/init.h> -#include <linux/pci.h> -#include <linux/interrupt.h> -#include <linux/time.h> -#include <linux/delay.h> - -#include <asm/time.h> - -#include <asm/octeon/octeon.h> -#include <asm/octeon/cvmx-npi-defs.h> -#include <asm/octeon/cvmx-pci-defs.h> - -#include "pci-common.h" - -#define USE_OCTEON_INTERNAL_ARBITER - -/* - * Octeon's PCI controller uses did=3, subdid=2 for PCI IO - * addresses. Use PCI endian swapping 1 so no address swapping is - * necessary. The Linux io routines will endian swap the data. - */ -#define OCTEON_PCI_IOSPACE_BASE 0x80011a0400000000ull -#define OCTEON_PCI_IOSPACE_SIZE (1ull<<32) - -/* Octeon't PCI controller uses did=3, subdid=3 for PCI memory. */ -#define OCTEON_PCI_MEMSPACE_OFFSET (0x00011b0000000000ull) - -/** - * This is the bit decoding used for the Octeon PCI controller addresses - */ -union octeon_pci_address { - uint64_t u64; - struct { - uint64_t upper:2; - uint64_t reserved:13; - uint64_t io:1; - uint64_t did:5; - uint64_t subdid:3; - uint64_t reserved2:4; - uint64_t endian_swap:2; - uint64_t reserved3:10; - uint64_t bus:8; - uint64_t dev:5; - uint64_t func:3; - uint64_t reg:8; - } s; -}; - -/** - * Return the mapping of PCI device number to IRQ line. Each - * character in the return string represents the interrupt - * line for the device at that position. Device 1 maps to the - * first character, etc. The characters A-D are used for PCI - * interrupts. - * - * Returns PCI interrupt mapping - */ -const char *octeon_get_pci_interrupts(void) -{ - /* - * Returning an empty string causes the interrupts to be - * routed based on the PCI specification. From the PCI spec: - * - * INTA# of Device Number 0 is connected to IRQW on the system - * board. (Device Number has no significance regarding being - * located on the system board or in a connector.) INTA# of - * Device Number 1 is connected to IRQX on the system - * board. INTA# of Device Number 2 is connected to IRQY on the - * system board. INTA# of Device Number 3 is connected to IRQZ - * on the system board. The table below describes how each - * agent's INTx# lines are connected to the system board - * interrupt lines. The following equation can be used to - * determine to which INTx# signal on the system board a given - * device's INTx# line(s) is connected. - * - * MB = (D + I) MOD 4 MB = System board Interrupt (IRQW = 0, - * IRQX = 1, IRQY = 2, and IRQZ = 3) D = Device Number I = - * Interrupt Number (INTA# = 0, INTB# = 1, INTC# = 2, and - * INTD# = 3) - */ - switch (octeon_bootinfo->board_type) { - case CVMX_BOARD_TYPE_NAO38: - /* This is really the NAC38 */ - return "AAAAADABAAAAAAAAAAAAAAAAAAAAAAAA"; - case CVMX_BOARD_TYPE_THUNDER: - return ""; - case CVMX_BOARD_TYPE_EBH3000: - return ""; - case CVMX_BOARD_TYPE_EBH3100: - case CVMX_BOARD_TYPE_CN3010_EVB_HS5: - case CVMX_BOARD_TYPE_CN3005_EVB_HS5: - return "AAABAAAAAAAAAAAAAAAAAAAAAAAAAAAA"; - case CVMX_BOARD_TYPE_BBGW_REF: - return "AABCD"; - default: - return ""; - } -} - -/** - * Map a PCI device to the appropriate interrupt line - * - * @dev: The Linux PCI device structure for the device to map - * @slot: The slot number for this device on __BUS 0__. Linux - * enumerates through all the bridges and figures out the - * slot on Bus 0 where this device eventually hooks to. - * @pin: The PCI interrupt pin read from the device, then swizzled - * as it goes through each bridge. - * Returns Interrupt number for the device - */ -int __init octeon_pci_pcibios_map_irq(const struct pci_dev *dev, - u8 slot, u8 pin) -{ - int irq_num; - const char *interrupts; - int dev_num; - - /* Get the board specific interrupt mapping */ - interrupts = octeon_get_pci_interrupts(); - - dev_num = dev->devfn >> 3; - if (dev_num < strlen(interrupts)) - irq_num = ((interrupts[dev_num] - 'A' + pin - 1) & 3) + - OCTEON_IRQ_PCI_INT0; - else - irq_num = ((slot + pin - 3) & 3) + OCTEON_IRQ_PCI_INT0; - return irq_num; -} - - -/** - * Read a value from configuration space - * - */ -static int octeon_read_config(struct pci_bus *bus, unsigned int devfn, - int reg, int size, u32 *val) -{ - union octeon_pci_address pci_addr; - - pci_addr.u64 = 0; - pci_addr.s.upper = 2; - pci_addr.s.io = 1; - pci_addr.s.did = 3; - pci_addr.s.subdid = 1; - pci_addr.s.endian_swap = 1; - pci_addr.s.bus = bus->number; - pci_addr.s.dev = devfn >> 3; - pci_addr.s.func = devfn & 0x7; - pci_addr.s.reg = reg; - -#if PCI_CONFIG_SPACE_DELAY - udelay(PCI_CONFIG_SPACE_DELAY); -#endif - switch (size) { - case 4: - *val = le32_to_cpu(cvmx_read64_uint32(pci_addr.u64)); - return PCIBIOS_SUCCESSFUL; - case 2: - *val = le16_to_cpu(cvmx_read64_uint16(pci_addr.u64)); - return PCIBIOS_SUCCESSFUL; - case 1: - *val = cvmx_read64_uint8(pci_addr.u64); - return PCIBIOS_SUCCESSFUL; - } - return PCIBIOS_FUNC_NOT_SUPPORTED; -} - - -/** - * Write a value to PCI configuration space - * - * @bus: - * @devfn: - * @reg: - * @size: - * @val: - * Returns - */ -static int octeon_write_config(struct pci_bus *bus, unsigned int devfn, - int reg, int size, u32 val) -{ - union octeon_pci_address pci_addr; - - pci_addr.u64 = 0; - pci_addr.s.upper = 2; - pci_addr.s.io = 1; - pci_addr.s.did = 3; - pci_addr.s.subdid = 1; - pci_addr.s.endian_swap = 1; - pci_addr.s.bus = bus->number; - pci_addr.s.dev = devfn >> 3; - pci_addr.s.func = devfn & 0x7; - pci_addr.s.reg = reg; - -#if PCI_CONFIG_SPACE_DELAY - udelay(PCI_CONFIG_SPACE_DELAY); -#endif - switch (size) { - case 4: - cvmx_write64_uint32(pci_addr.u64, cpu_to_le32(val)); - return PCIBIOS_SUCCESSFUL; - case 2: - cvmx_write64_uint16(pci_addr.u64, cpu_to_le16(val)); - return PCIBIOS_SUCCESSFUL; - case 1: - cvmx_write64_uint8(pci_addr.u64, val); - return PCIBIOS_SUCCESSFUL; - } - return PCIBIOS_FUNC_NOT_SUPPORTED; -} - - -static struct pci_ops octeon_pci_ops = { - octeon_read_config, - octeon_write_config, -}; - -static struct resource octeon_pci_mem_resource = { - .start = 0, - .end = 0, - .name = "Octeon PCI MEM", - .flags = IORESOURCE_MEM, -}; - -/* - * PCI ports must be above 16KB so the ISA bus filtering in the PCI-X to PCI - * bridge - */ -static struct resource octeon_pci_io_resource = { - .start = 0x4000, - .end = OCTEON_PCI_IOSPACE_SIZE - 1, - .name = "Octeon PCI IO", - .flags = IORESOURCE_IO, -}; - -static struct pci_controller octeon_pci_controller = { - .pci_ops = &octeon_pci_ops, - .mem_resource = &octeon_pci_mem_resource, - .mem_offset = OCTEON_PCI_MEMSPACE_OFFSET, - .io_resource = &octeon_pci_io_resource, - .io_offset = 0, - .io_map_base = OCTEON_PCI_IOSPACE_BASE, -}; - - -/** - * Low level initialize the Octeon PCI controller - * - * Returns - */ -static void octeon_pci_initialize(void) -{ - union cvmx_pci_cfg01 cfg01; - union cvmx_npi_ctl_status ctl_status; - union cvmx_pci_ctl_status_2 ctl_status_2; - union cvmx_pci_cfg19 cfg19; - union cvmx_pci_cfg16 cfg16; - union cvmx_pci_cfg22 cfg22; - union cvmx_pci_cfg56 cfg56; - - /* Reset the PCI Bus */ - cvmx_write_csr(CVMX_CIU_SOFT_PRST, 0x1); - cvmx_read_csr(CVMX_CIU_SOFT_PRST); - - udelay(2000); /* Hold PCI reset for 2 ms */ - - ctl_status.u64 = 0; /* cvmx_read_csr(CVMX_NPI_CTL_STATUS); */ - ctl_status.s.max_word = 1; - ctl_status.s.timer = 1; - cvmx_write_csr(CVMX_NPI_CTL_STATUS, ctl_status.u64); - - /* Deassert PCI reset and advertize PCX Host Mode Device Capability - (64b) */ - cvmx_write_csr(CVMX_CIU_SOFT_PRST, 0x4); - cvmx_read_csr(CVMX_CIU_SOFT_PRST); - - udelay(2000); /* Wait 2 ms after deasserting PCI reset */ - - ctl_status_2.u32 = 0; - ctl_status_2.s.tsr_hwm = 1; /* Initializes to 0. Must be set - before any PCI reads. */ - ctl_status_2.s.bar2pres = 1; /* Enable BAR2 */ - ctl_status_2.s.bar2_enb = 1; - ctl_status_2.s.bar2_cax = 1; /* Don't use L2 */ - ctl_status_2.s.bar2_esx = 1; - ctl_status_2.s.pmo_amod = 1; /* Round robin priority */ - if (octeon_dma_bar_type == OCTEON_DMA_BAR_TYPE_BIG) { - /* BAR1 hole */ - ctl_status_2.s.bb1_hole = OCTEON_PCI_BAR1_HOLE_BITS; - ctl_status_2.s.bb1_siz = 1; /* BAR1 is 2GB */ - ctl_status_2.s.bb_ca = 1; /* Don't use L2 with big bars */ - ctl_status_2.s.bb_es = 1; /* Big bar in byte swap mode */ - ctl_status_2.s.bb1 = 1; /* BAR1 is big */ - ctl_status_2.s.bb0 = 1; /* BAR0 is big */ - } - - octeon_npi_write32(CVMX_NPI_PCI_CTL_STATUS_2, ctl_status_2.u32); - udelay(2000); /* Wait 2 ms before doing PCI reads */ - - ctl_status_2.u32 = octeon_npi_read32(CVMX_NPI_PCI_CTL_STATUS_2); - pr_notice("PCI Status: %s %s-bit\n", - ctl_status_2.s.ap_pcix ? "PCI-X" : "PCI", - ctl_status_2.s.ap_64ad ? "64" : "32"); - - if (OCTEON_IS_MODEL(OCTEON_CN58XX) || OCTEON_IS_MODEL(OCTEON_CN50XX)) { - union cvmx_pci_cnt_reg cnt_reg_start; - union cvmx_pci_cnt_reg cnt_reg_end; - unsigned long cycles, pci_clock; - - cnt_reg_start.u64 = cvmx_read_csr(CVMX_NPI_PCI_CNT_REG); - cycles = read_c0_cvmcount(); - udelay(1000); - cnt_reg_end.u64 = cvmx_read_csr(CVMX_NPI_PCI_CNT_REG); - cycles = read_c0_cvmcount() - cycles; - pci_clock = (cnt_reg_end.s.pcicnt - cnt_reg_start.s.pcicnt) / - (cycles / (mips_hpt_frequency / 1000000)); - pr_notice("PCI Clock: %lu MHz\n", pci_clock); - } - - /* - * TDOMC must be set to one in PCI mode. TDOMC should be set to 4 - * in PCI-X mode to allow four oustanding splits. Otherwise, - * should not change from its reset value. Don't write PCI_CFG19 - * in PCI mode (0x82000001 reset value), write it to 0x82000004 - * after PCI-X mode is known. MRBCI,MDWE,MDRE -> must be zero. - * MRBCM -> must be one. - */ - if (ctl_status_2.s.ap_pcix) { - cfg19.u32 = 0; - /* - * Target Delayed/Split request outstanding maximum - * count. [1..31] and 0=32. NOTE: If the user - * programs these bits beyond the Designed Maximum - * outstanding count, then the designed maximum table - * depth will be used instead. No additional - * Deferred/Split transactions will be accepted if - * this outstanding maximum count is - * reached. Furthermore, no additional deferred/split - * transactions will be accepted if the I/O delay/ I/O - * Split Request outstanding maximum is reached. - */ - cfg19.s.tdomc = 4; - /* - * Master Deferred Read Request Outstanding Max Count - * (PCI only). CR4C[26:24] Max SAC cycles MAX DAC - * cycles 000 8 4 001 1 0 010 2 1 011 3 1 100 4 2 101 - * 5 2 110 6 3 111 7 3 For example, if these bits are - * programmed to 100, the core can support 2 DAC - * cycles, 4 SAC cycles or a combination of 1 DAC and - * 2 SAC cycles. NOTE: For the PCI-X maximum - * outstanding split transactions, refer to - * CRE0[22:20]. - */ - cfg19.s.mdrrmc = 2; - /* - * Master Request (Memory Read) Byte Count/Byte Enable - * select. 0 = Byte Enables valid. In PCI mode, a - * burst transaction cannot be performed using Memory - * Read command=4?h6. 1 = DWORD Byte Count valid - * (default). In PCI Mode, the memory read byte - * enables are automatically generated by the - * core. Note: N3 Master Request transaction sizes are - * always determined through the - * am_attr[<35:32>|<7:0>] field. - */ - cfg19.s.mrbcm = 1; - octeon_npi_write32(CVMX_NPI_PCI_CFG19, cfg19.u32); - } - - - cfg01.u32 = 0; - cfg01.s.msae = 1; /* Memory Space Access Enable */ - cfg01.s.me = 1; /* Master Enable */ - cfg01.s.pee = 1; /* PERR# Enable */ - cfg01.s.see = 1; /* System Error Enable */ - cfg01.s.fbbe = 1; /* Fast Back to Back Transaction Enable */ - - octeon_npi_write32(CVMX_NPI_PCI_CFG01, cfg01.u32); - -#ifdef USE_OCTEON_INTERNAL_ARBITER - /* - * When OCTEON is a PCI host, most systems will use OCTEON's - * internal arbiter, so must enable it before any PCI/PCI-X - * traffic can occur. - */ - { - union cvmx_npi_pci_int_arb_cfg pci_int_arb_cfg; - - pci_int_arb_cfg.u64 = 0; - pci_int_arb_cfg.s.en = 1; /* Internal arbiter enable */ - cvmx_write_csr(CVMX_NPI_PCI_INT_ARB_CFG, pci_int_arb_cfg.u64); - } -#endif /* USE_OCTEON_INTERNAL_ARBITER */ - - /* - * Preferrably written to 1 to set MLTD. [RDSATI,TRTAE, - * TWTAE,TMAE,DPPMR -> must be zero. TILT -> must not be set to - * 1..7. - */ - cfg16.u32 = 0; - cfg16.s.mltd = 1; /* Master Latency Timer Disable */ - octeon_npi_write32(CVMX_NPI_PCI_CFG16, cfg16.u32); - - /* - * Should be written to 0x4ff00. MTTV -> must be zero. - * FLUSH -> must be 1. MRV -> should be 0xFF. - */ - cfg22.u32 = 0; - /* Master Retry Value [1..255] and 0=infinite */ - cfg22.s.mrv = 0xff; - /* - * AM_DO_FLUSH_I control NOTE: This bit MUST BE ONE for proper - * N3K operation. - */ - cfg22.s.flush = 1; - octeon_npi_write32(CVMX_NPI_PCI_CFG22, cfg22.u32); - - /* - * MOST Indicates the maximum number of outstanding splits (in -1 - * notation) when OCTEON is in PCI-X mode. PCI-X performance is - * affected by the MOST selection. Should generally be written - * with one of 0x3be807, 0x2be807, 0x1be807, or 0x0be807, - * depending on the desired MOST of 3, 2, 1, or 0, respectively. - */ - cfg56.u32 = 0; - cfg56.s.pxcid = 7; /* RO - PCI-X Capability ID */ - cfg56.s.ncp = 0xe8; /* RO - Next Capability Pointer */ - cfg56.s.dpere = 1; /* Data Parity Error Recovery Enable */ - cfg56.s.roe = 1; /* Relaxed Ordering Enable */ - cfg56.s.mmbc = 1; /* Maximum Memory Byte Count - [0=512B,1=1024B,2=2048B,3=4096B] */ - cfg56.s.most = 3; /* Maximum outstanding Split transactions [0=1 - .. 7=32] */ - - octeon_npi_write32(CVMX_NPI_PCI_CFG56, cfg56.u32); - - /* - * Affects PCI performance when OCTEON services reads to its - * BAR1/BAR2. Refer to Section 10.6.1. The recommended values are - * 0x22, 0x33, and 0x33 for PCI_READ_CMD_6, PCI_READ_CMD_C, and - * PCI_READ_CMD_E, respectively. Unfortunately due to errata DDR-700, - * these values need to be changed so they won't possibly prefetch off - * of the end of memory if PCI is DMAing a buffer at the end of - * memory. Note that these values differ from their reset values. - */ - octeon_npi_write32(CVMX_NPI_PCI_READ_CMD_6, 0x21); - octeon_npi_write32(CVMX_NPI_PCI_READ_CMD_C, 0x31); - octeon_npi_write32(CVMX_NPI_PCI_READ_CMD_E, 0x31); -} - - -/** - * Initialize the Octeon PCI controller - * - * Returns - */ -static int __init octeon_pci_setup(void) -{ - union cvmx_npi_mem_access_subidx mem_access; - int index; - - /* Only these chips have PCI */ - if (octeon_has_feature(OCTEON_FEATURE_PCIE)) - return 0; - - /* Point pcibios_map_irq() to the PCI version of it */ - octeon_pcibios_map_irq = octeon_pci_pcibios_map_irq; - - /* Only use the big bars on chips that support it */ - if (OCTEON_IS_MODEL(OCTEON_CN31XX) || - OCTEON_IS_MODEL(OCTEON_CN38XX_PASS2) || - OCTEON_IS_MODEL(OCTEON_CN38XX_PASS1)) - octeon_dma_bar_type = OCTEON_DMA_BAR_TYPE_SMALL; - else - octeon_dma_bar_type = OCTEON_DMA_BAR_TYPE_BIG; - - /* PCI I/O and PCI MEM values */ - set_io_port_base(OCTEON_PCI_IOSPACE_BASE); - ioport_resource.start = 0; - ioport_resource.end = OCTEON_PCI_IOSPACE_SIZE - 1; - if (!octeon_is_pci_host()) { - pr_notice("Not in host mode, PCI Controller not initialized\n"); - return 0; - } - - pr_notice("%s Octeon big bar support\n", - (octeon_dma_bar_type == - OCTEON_DMA_BAR_TYPE_BIG) ? "Enabling" : "Disabling"); - - octeon_pci_initialize(); - - mem_access.u64 = 0; - mem_access.s.esr = 1; /* Endian-Swap on read. */ - mem_access.s.esw = 1; /* Endian-Swap on write. */ - mem_access.s.nsr = 0; /* No-Snoop on read. */ - mem_access.s.nsw = 0; /* No-Snoop on write. */ - mem_access.s.ror = 0; /* Relax Read on read. */ - mem_access.s.row = 0; /* Relax Order on write. */ - mem_access.s.ba = 0; /* PCI Address bits [63:36]. */ - cvmx_write_csr(CVMX_NPI_MEM_ACCESS_SUBID3, mem_access.u64); - - /* - * Remap the Octeon BAR 2 above all 32 bit devices - * (0x8000000000ul). This is done here so it is remapped - * before the readl()'s below. We don't want BAR2 overlapping - * with BAR0/BAR1 during these reads. - */ - octeon_npi_write32(CVMX_NPI_PCI_CFG08, 0); - octeon_npi_write32(CVMX_NPI_PCI_CFG09, 0x80); - - /* Disable the BAR1 movable mappings */ - for (index = 0; index < 32; index++) - octeon_npi_write32(CVMX_NPI_PCI_BAR1_INDEXX(index), 0); - - if (octeon_dma_bar_type == OCTEON_DMA_BAR_TYPE_BIG) { - /* Remap the Octeon BAR 0 to 0-2GB */ - octeon_npi_write32(CVMX_NPI_PCI_CFG04, 0); - octeon_npi_write32(CVMX_NPI_PCI_CFG05, 0); - - /* - * Remap the Octeon BAR 1 to map 2GB-4GB (minus the - * BAR 1 hole). - */ - octeon_npi_write32(CVMX_NPI_PCI_CFG06, 2ul << 30); - octeon_npi_write32(CVMX_NPI_PCI_CFG07, 0); - - /* Devices go after BAR1 */ - octeon_pci_mem_resource.start = - OCTEON_PCI_MEMSPACE_OFFSET + (4ul << 30) - - (OCTEON_PCI_BAR1_HOLE_SIZE << 20); - octeon_pci_mem_resource.end = - octeon_pci_mem_resource.start + (1ul << 30); - } else { - /* Remap the Octeon BAR 0 to map 128MB-(128MB+4KB) */ - octeon_npi_write32(CVMX_NPI_PCI_CFG04, 128ul << 20); - octeon_npi_write32(CVMX_NPI_PCI_CFG05, 0); - - /* Remap the Octeon BAR 1 to map 0-128MB */ - octeon_npi_write32(CVMX_NPI_PCI_CFG06, 0); - octeon_npi_write32(CVMX_NPI_PCI_CFG07, 0); - - /* Devices go after BAR0 */ - octeon_pci_mem_resource.start = - OCTEON_PCI_MEMSPACE_OFFSET + (128ul << 20) + - (4ul << 10); - octeon_pci_mem_resource.end = - octeon_pci_mem_resource.start + (1ul << 30); - } - - register_pci_controller(&octeon_pci_controller); - - /* - * Clear any errors that might be pending from before the bus - * was setup properly. - */ - cvmx_write_csr(CVMX_NPI_PCI_INT_SUM2, -1); - return 0; -} - -arch_initcall(octeon_pci_setup); |
