diff options
Diffstat (limited to 'arch/mips/alchemy/pb1500/board_setup.c')
| -rw-r--r-- | arch/mips/alchemy/pb1500/board_setup.c | 119 |
1 files changed, 119 insertions, 0 deletions
diff --git a/arch/mips/alchemy/pb1500/board_setup.c b/arch/mips/alchemy/pb1500/board_setup.c new file mode 100644 index 0000000..035771c --- /dev/null +++ b/arch/mips/alchemy/pb1500/board_setup.c @@ -0,0 +1,119 @@ +/* + * Copyright 2000, 2008 MontaVista Software Inc. + * Author: MontaVista Software, Inc. <source@mvista.com> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED + * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN + * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT + * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF + * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON + * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF + * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + * You should have received a copy of the GNU General Public License along + * with this program; if not, write to the Free Software Foundation, Inc., + * 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#include <linux/init.h> +#include <linux/delay.h> + +#include <asm/mach-au1x00/au1000.h> +#include <asm/mach-pb1x00/pb1500.h> + +void board_reset(void) +{ + /* Hit BCSR.RST_VDDI[SOFT_RESET] */ + au_writel(0x00000000, PB1500_RST_VDDI); +} + +void __init board_setup(void) +{ + u32 pin_func; + u32 sys_freqctrl, sys_clksrc; + + sys_clksrc = sys_freqctrl = pin_func = 0; + /* Set AUX clock to 12 MHz * 8 = 96 MHz */ + au_writel(8, SYS_AUXPLL); + au_writel(0, SYS_PINSTATERD); + udelay(100); + +#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) + + /* GPIO201 is input for PCMCIA card detect */ + /* GPIO203 is input for PCMCIA interrupt request */ + au_writel(au_readl(GPIO2_DIR) & ~((1 << 1) | (1 << 3)), GPIO2_DIR); + + /* Zero and disable FREQ2 */ + sys_freqctrl = au_readl(SYS_FREQCTRL0); + sys_freqctrl &= ~0xFFF00000; + au_writel(sys_freqctrl, SYS_FREQCTRL0); + + /* zero and disable USBH/USBD clocks */ + sys_clksrc = au_readl(SYS_CLKSRC); + sys_clksrc &= ~(SYS_CS_CUD | SYS_CS_DUD | SYS_CS_MUD_MASK | + SYS_CS_CUH | SYS_CS_DUH | SYS_CS_MUH_MASK); + au_writel(sys_clksrc, SYS_CLKSRC); + + sys_freqctrl = au_readl(SYS_FREQCTRL0); + sys_freqctrl &= ~0xFFF00000; + + sys_clksrc = au_readl(SYS_CLKSRC); + sys_clksrc &= ~(SYS_CS_CUD | SYS_CS_DUD | SYS_CS_MUD_MASK | + SYS_CS_CUH | SYS_CS_DUH | SYS_CS_MUH_MASK); + + /* FREQ2 = aux/2 = 48 MHz */ + sys_freqctrl |= (0 << SYS_FC_FRDIV2_BIT) | SYS_FC_FE2 | SYS_FC_FS2; + au_writel(sys_freqctrl, SYS_FREQCTRL0); + + /* + * Route 48MHz FREQ2 into USB Host and/or Device + */ + sys_clksrc |= SYS_CS_MUX_FQ2 << SYS_CS_MUH_BIT; + au_writel(sys_clksrc, SYS_CLKSRC); + + pin_func = au_readl(SYS_PINFUNC) & ~SYS_PF_USB; + /* 2nd USB port is USB host */ + pin_func |= SYS_PF_USB; + au_writel(pin_func, SYS_PINFUNC); +#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */ + +#ifdef CONFIG_PCI + /* Setup PCI bus controller */ + au_writel(0, Au1500_PCI_CMEM); + au_writel(0x00003fff, Au1500_CFG_BASE); +#if defined(__MIPSEB__) + au_writel(0xf | (2 << 6) | (1 << 4), Au1500_PCI_CFG); +#else + au_writel(0xf, Au1500_PCI_CFG); +#endif + au_writel(0xf0000000, Au1500_PCI_MWMASK_DEV); + au_writel(0, Au1500_PCI_MWBASE_REV_CCL); + au_writel(0x02a00356, Au1500_PCI_STATCMD); + au_writel(0x00003c04, Au1500_PCI_HDRTYPE); + au_writel(0x00000008, Au1500_PCI_MBAR); + au_sync(); +#endif + + /* Enable sys bus clock divider when IDLE state or no bus activity. */ + au_writel(au_readl(SYS_POWERCTRL) | (0x3 << 5), SYS_POWERCTRL); + + /* Enable the RTC if not already enabled */ + if (!(au_readl(0xac000028) & 0x20)) { + printk(KERN_INFO "enabling clock ...\n"); + au_writel((au_readl(0xac000028) | 0x20), 0xac000028); + } + /* Put the clock in BCD mode */ + if (au_readl(0xac00002c) & 0x4) { /* reg B */ + au_writel(au_readl(0xac00002c) & ~0x4, 0xac00002c); + au_sync(); + } +} |
