summaryrefslogtreecommitdiffstats
path: root/arch/mips/Kconfig
diff options
context:
space:
mode:
Diffstat (limited to 'arch/mips/Kconfig')
-rw-r--r--arch/mips/Kconfig32
1 files changed, 25 insertions, 7 deletions
diff --git a/arch/mips/Kconfig b/arch/mips/Kconfig
index 1443024..27f83e6 100644
--- a/arch/mips/Kconfig
+++ b/arch/mips/Kconfig
@@ -266,8 +266,8 @@ config MIPS_MALTA
select BOOT_ELF32
select HAVE_STD_PC_SERIAL_PORT
select DMA_NONCOHERENT
- select IRQ_CPU
select GENERIC_ISA_DMA
+ select IRQ_CPU
select HW_HAS_PCI
select I8259
select MIPS_BOARDS_GEN
@@ -534,7 +534,7 @@ config SGI_IP22
select HW_HAS_EISA
select IP22_CPU_SCACHE
select IRQ_CPU
- select NO_ISA if ISA
+ select GENERIC_ISA_DMA_SUPPORT_BROKEN
select SWAP_IO_SPACE
select SYS_HAS_CPU_R4X00
select SYS_HAS_CPU_R5000
@@ -766,6 +766,23 @@ config TOSHIBA_RBTX4938
endchoice
+config KEXEC
+ bool "Kexec system call (EXPERIMENTAL)"
+ depends on EXPERIMENTAL
+ help
+ kexec is a system call that implements the ability to shutdown your
+ current kernel, and to start another kernel. It is like a reboot
+ but it is indepedent of the system firmware. And like a reboot
+ you can start any kernel with it, not just Linux.
+
+ The name comes from the similiarity to the exec system call.
+
+ It is an ongoing process to be certain the hardware in a machine
+ is properly shutdown, so do not be surprised if this code does not
+ initially work for you. It may help to enable device hotplugging
+ support. As of this writing the exact hardware interface is
+ strongly in flux, so no good recommendation can be made.
+
source "arch/mips/ddb5xxx/Kconfig"
source "arch/mips/gt64120/ev64120/Kconfig"
source "arch/mips/jazz/Kconfig"
@@ -864,8 +881,11 @@ config MIPS_NILE4
config MIPS_DISABLE_OBSOLETE_IDE
bool
+config GENERIC_ISA_DMA_SUPPORT_BROKEN
+ bool
+
#
-# Endianess selection. Suffiently obscure so many users don't know what to
+# Endianess selection. Sufficiently obscure so many users don't know what to
# answer,so we try hard to limit the available choices. Also the use of a
# choice statement should be more obvious to the user.
#
@@ -874,7 +894,7 @@ choice
help
Some MIPS machines can be configured for either little or big endian
byte order. These modes require different kernels and a different
- Linux distribution. In general there is one prefered byteorder for a
+ Linux distribution. In general there is one preferred byteorder for a
particular system but some systems are just as commonly used in the
one or the other endianess.
@@ -1835,13 +1855,11 @@ source "drivers/pci/Kconfig"
config ISA
bool
-config NO_ISA
- bool
-
config EISA
bool "EISA support"
depends on HW_HAS_EISA
select ISA
+ select GENERIC_ISA_DMA
---help---
The Extended Industry Standard Architecture (EISA) bus was
developed as an open alternative to the IBM MicroChannel bus.
OpenPOWER on IntegriCloud