diff options
Diffstat (limited to 'arch/cris/Kconfig')
| -rw-r--r-- | arch/cris/Kconfig | 82 |
1 files changed, 0 insertions, 82 deletions
diff --git a/arch/cris/Kconfig b/arch/cris/Kconfig index 3201ddb..02380be 100644 --- a/arch/cris/Kconfig +++ b/arch/cris/Kconfig @@ -41,7 +41,6 @@ config CRIS default y select HAVE_IDE select GENERIC_ATOMIC64 - select HAVE_GENERIC_HARDIRQS select HAVE_UID16 select VIRT_TO_BUS select ARCH_WANT_IPC_PARSE_VERSION @@ -99,9 +98,6 @@ config ETRAX_KMALLOCED_MODULES help Enable module allocation with kmalloc instead of vmalloc. -config OOM_REBOOT - bool "Enable reboot at out of memory" - source "kernel/Kconfig.preempt" source mm/Kconfig @@ -175,12 +171,6 @@ config ETRAX_FLASH_BUSWIDTH help Width in bytes of the NOR Flash bus (1, 2 or 4). Is usually 2. -config ETRAX_NANDFLASH_BUSWIDTH - int "Buswidth of NAND flash in bytes" - default "1" - help - Width in bytes of the NAND flash (1 or 2). - config ETRAX_FLASH1_SIZE int "FLASH1 size (dec, in MB. 0 = Unknown)" default "0" @@ -272,38 +262,6 @@ config ETRAX_AXISFLASHMAP This option enables MTD mapping of flash devices. Needed to use flash memories. If unsure, say Y. -config ETRAX_RTC - bool "Real Time Clock support" - depends on ETRAX_I2C - help - Enables drivers for the Real-Time Clock battery-backed chips on - some products. The kernel reads the time when booting, and - the date can be set using ioctl(fd, RTC_SET_TIME, &rt) with rt a - rtc_time struct (see <file:arch/cris/include/asm/rtc.h>) on the - /dev/rtc device. You can check the time with cat /proc/rtc, but - normal time reading should be done using libc function time and - friends. - -choice - prompt "RTC chip" - depends on ETRAX_RTC - default ETRAX_DS1302 - -config ETRAX_DS1302 - depends on ETRAX_ARCH_V10 - bool "DS1302" - help - Enables the driver for the DS1302 Real-Time Clock battery-backed - chip on some products. - -config ETRAX_PCF8563 - bool "PCF8563" - help - Enables the driver for the PCF8563 Real-Time Clock battery-backed - chip on some products. - -endchoice - config ETRAX_SYNCHRONOUS_SERIAL bool "Synchronous serial-port support" help @@ -578,26 +536,6 @@ config ETRAX_SERIAL_PORT3_DMA5_IN depends on ETRAX_ARCH_V10 bool "DMA 5" -config ETRAX_SERIAL_PORT3_DMA9_IN - bool "Ser3 uses DMA9 for input" - depends on ETRAXFS - help - Enables the DMA9 input channel for ser3 (ttyS3). - If you do not enable DMA, an interrupt for each character will be - used when receiving data. - Normally you want to use DMA, unless you use the DMA channel for - something else. - -config ETRAX_SERIAL_PORT3_DMA3_IN - bool "Ser3 uses DMA3 for input" - depends on CRIS_MACH_ARTPEC3 - help - Enables the DMA3 input channel for ser3 (ttyS3). - If you do not enable DMA, an interrupt for each character will be - used when receiving data. - Normally you want to use DMA, unless you use the DMA channel for - something else. - endchoice choice @@ -615,26 +553,6 @@ config ETRAX_SERIAL_PORT3_DMA4_OUT depends on ETRAX_ARCH_V10 bool "DMA 4" -config ETRAX_SERIAL_PORT3_DMA8_OUT - bool "Ser3 uses DMA8 for output" - depends on ETRAXFS - help - Enables the DMA8 output channel for ser3 (ttyS3). - If you do not enable DMA, an interrupt for each character will be - used when transmitting data. - Normally you want to use DMA, unless you use the DMA channel for - something else. - -config ETRAX_SERIAL_PORT3_DMA2_OUT - bool "Ser3 uses DMA2 for output" - depends on CRIS_MACH_ARTPEC3 - help - Enables the DMA2 output channel for ser3 (ttyS3). - If you do not enable DMA, an interrupt for each character will be - used when transmitting data. - Normally you want to use DMA, unless you use the DMA channel for - something else. - endchoice endmenu |
