diff options
Diffstat (limited to 'arch/avr32')
45 files changed, 2627 insertions, 680 deletions
diff --git a/arch/avr32/Makefile b/arch/avr32/Makefile index 5b46433..c9e1f0b 100644 --- a/arch/avr32/Makefile +++ b/arch/avr32/Makefile @@ -39,20 +39,6 @@ core-y += arch/avr32/mm/ drivers-$(CONFIG_OPROFILE) += arch/avr32/oprofile/ libs-y += arch/avr32/lib/ -archincdir-$(CONFIG_PLATFORM_AT32AP) := arch-at32ap - -include/asm-avr32/.arch: $(wildcard include/config/platform/*.h) include/config/auto.conf - @echo ' SYMLINK include/asm-avr32/arch -> include/asm-avr32/$(archincdir-y)' -ifneq ($(KBUILD_SRC),) - $(Q)mkdir -p include/asm-avr32 - $(Q)ln -fsn $(srctree)/include/asm-avr32/$(archincdir-y) include/asm-avr32/arch -else - $(Q)ln -fsn $(archincdir-y) include/asm-avr32/arch -endif - @touch $@ - -archprepare: include/asm-avr32/.arch - CLEAN_FILES += include/asm-avr32/.arch include/asm-avr32/arch BOOT_TARGETS := vmlinux.elf vmlinux.bin uImage uImage.srec diff --git a/arch/avr32/boards/atngw100/setup.c b/arch/avr32/boards/atngw100/setup.c index 670c87b..6c54580 100644 --- a/arch/avr32/boards/atngw100/setup.c +++ b/arch/avr32/boards/atngw100/setup.c @@ -9,6 +9,7 @@ */ #include <linux/clk.h> #include <linux/etherdevice.h> +#include <linux/gpio.h> #include <linux/irq.h> #include <linux/i2c.h> #include <linux/i2c-gpio.h> @@ -47,14 +48,17 @@ static struct eth_platform_data __initdata eth_data[2]; static struct spi_board_info spi0_board_info[] __initdata = { { .modalias = "mtd_dataflash", - .max_speed_hz = 10000000, + .max_speed_hz = 8000000, .chip_select = 0, }, }; static struct mci_platform_data __initdata mci0_data = { - .detect_pin = GPIO_PIN_PC(25), - .wp_pin = GPIO_PIN_PE(0), + .slot[0] = { + .bus_width = 4, + .detect_pin = GPIO_PIN_PC(25), + .wp_pin = GPIO_PIN_PE(0), + }, }; /* @@ -190,7 +194,7 @@ static int __init atngw100_init(void) * PB28/EXTINT3 doesn't; it should be SMBALERT# (for PMBus), * but it's not available off-board. */ - at32_select_periph(GPIO_PIN_PB(28), 0, AT32_GPIOF_PULLUP); + at32_select_periph(GPIO_PIOB_BASE, 1 << 28, 0, AT32_GPIOF_PULLUP); at32_select_gpio(i2c_gpio_data.sda_pin, AT32_GPIOF_MULTIDRV | AT32_GPIOF_OUTPUT | AT32_GPIOF_HIGH); at32_select_gpio(i2c_gpio_data.scl_pin, @@ -204,6 +208,15 @@ postcore_initcall(atngw100_init); static int __init atngw100_arch_init(void) { + /* PB30 is the otherwise unused jumper on the mainboard, with an + * external pullup; the jumper grounds it. Use it however you + * like, including letting U-Boot or Linux tweak boot sequences. + */ + at32_select_gpio(GPIO_PIN_PB(30), 0); + gpio_request(GPIO_PIN_PB(30), "j15"); + gpio_direction_input(GPIO_PIN_PB(30)); + gpio_export(GPIO_PIN_PB(30), false); + /* set_irq_type() after the arch_initcall for EIC has run, and * before the I2C subsystem could try using this IRQ. */ diff --git a/arch/avr32/boards/atstk1000/atstk1002.c b/arch/avr32/boards/atstk1000/atstk1002.c index b33542b..29e5b51 100644 --- a/arch/avr32/boards/atstk1000/atstk1002.c +++ b/arch/avr32/boards/atstk1000/atstk1002.c @@ -96,7 +96,7 @@ static struct mtd_partition *nand_part_info(int size, int *num_partitions) return nand_partitions; } -struct atmel_nand_data atstk1006_nand_data __initdata = { +static struct atmel_nand_data atstk1006_nand_data __initdata = { .cle = 21, .ale = 22, .rdy_pin = GPIO_PIN_PB(30), @@ -232,7 +232,7 @@ static void __init atstk1002_setup_extdac(void) goto err_set_clk; } - at32_select_periph(GPIO_PIN_PA(30), GPIO_PERIPH_A, 0); + at32_select_periph(GPIO_PIOA_BASE, (1 << 30), GPIO_PERIPH_A, 0); at73c213_data.dac_clk = gclk; err_set_clk: @@ -264,16 +264,20 @@ void __init setup_board(void) #ifndef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM +static struct mci_platform_data __initdata mci0_data = { + .slot[0] = { + .bus_width = 4, + /* MMC card detect requires MACB0 *NOT* be used */ #ifdef CONFIG_BOARD_ATSTK1002_SW6_CUSTOM -static struct mci_platform_data __initdata mci0_data = { - .detect_pin = GPIO_PIN_PC(14), /* gpio30/sdcd */ - .wp_pin = GPIO_PIN_PC(15), /* gpio31/sdwp */ -}; -#define MCI_PDATA &mci0_data + .detect_pin = GPIO_PIN_PC(14), /* gpio30/sdcd */ + .wp_pin = GPIO_PIN_PC(15), /* gpio31/sdwp */ #else -#define MCI_PDATA NULL + .detect_pin = -ENODEV, + .wp_pin = -ENODEV, #endif /* SW6 for sd{cd,wp} routing */ + }, +}; #endif /* SW2 for MMC signal routing */ @@ -325,14 +329,15 @@ static int __init atstk1002_init(void) #ifdef CONFIG_BOARD_ATSTK100X_SPI1 at32_add_device_spi(1, spi1_board_info, ARRAY_SIZE(spi1_board_info)); #endif -#ifndef CONFIG_BOARD_ATSTK1002_SW2_CUSTOM - at32_add_device_mci(0, MCI_PDATA); +#ifndef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM + at32_add_device_mci(0, &mci0_data); #endif #ifdef CONFIG_BOARD_ATSTK1002_SW5_CUSTOM set_hw_addr(at32_add_device_eth(1, ð_data[1])); #else at32_add_device_lcdc(0, &atstk1000_lcdc_data, - fbmem_start, fbmem_size, 0); + fbmem_start, fbmem_size, + ATMEL_LCDC_PRI_24BIT | ATMEL_LCDC_PRI_CONTROL); #endif at32_add_device_usba(0, NULL); #ifndef CONFIG_BOARD_ATSTK100X_SW3_CUSTOM diff --git a/arch/avr32/boards/atstk1000/atstk1003.c b/arch/avr32/boards/atstk1000/atstk1003.c index 0cf6641..be089d7f 100644 --- a/arch/avr32/boards/atstk1000/atstk1003.c +++ b/arch/avr32/boards/atstk1000/atstk1003.c @@ -19,6 +19,7 @@ #include <linux/spi/spi.h> #include <asm/setup.h> +#include <asm/atmel-mci.h> #include <mach/at32ap700x.h> #include <mach/board.h> @@ -66,6 +67,16 @@ static struct spi_board_info spi1_board_info[] __initdata = { { } }; #endif +#ifndef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM +static struct mci_platform_data __initdata mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = -ENODEV, + .wp_pin = -ENODEV, + }, +}; +#endif + #ifdef CONFIG_BOARD_ATSTK1000_EXTDAC static void __init atstk1003_setup_extdac(void) { @@ -84,7 +95,7 @@ static void __init atstk1003_setup_extdac(void) goto err_set_clk; } - at32_select_periph(GPIO_PIN_PA(30), GPIO_PERIPH_A, 0); + at32_select_periph(GPIO_PIOA_BASE, (1 << 30), GPIO_PERIPH_A, 0); at73c213_data.dac_clk = gclk; err_set_clk: @@ -154,7 +165,7 @@ static int __init atstk1003_init(void) at32_add_device_spi(1, spi1_board_info, ARRAY_SIZE(spi1_board_info)); #endif #ifndef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM - at32_add_device_mci(0, NULL); + at32_add_device_mci(0, &mci0_data); #endif at32_add_device_usba(0, NULL); #ifndef CONFIG_BOARD_ATSTK100X_SW3_CUSTOM diff --git a/arch/avr32/boards/atstk1000/atstk1004.c b/arch/avr32/boards/atstk1000/atstk1004.c index 50a5273..248ef23 100644 --- a/arch/avr32/boards/atstk1000/atstk1004.c +++ b/arch/avr32/boards/atstk1000/atstk1004.c @@ -21,6 +21,7 @@ #include <video/atmel_lcdc.h> #include <asm/setup.h> +#include <asm/atmel-mci.h> #include <mach/at32ap700x.h> #include <mach/board.h> @@ -71,6 +72,16 @@ static struct spi_board_info spi1_board_info[] __initdata = { { } }; #endif +#ifndef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM +static struct mci_platform_data __initdata mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = -ENODEV, + .wp_pin = -ENODEV, + }, +}; +#endif + #ifdef CONFIG_BOARD_ATSTK1000_EXTDAC static void __init atstk1004_setup_extdac(void) { @@ -89,7 +100,7 @@ static void __init atstk1004_setup_extdac(void) goto err_set_clk; } - at32_select_periph(GPIO_PIN_PA(30), GPIO_PERIPH_A, 0); + at32_select_periph(GPIO_PIOA_BASE, (1 << 30), GPIO_PERIPH_A, 0); at73c213_data.dac_clk = gclk; err_set_clk: @@ -137,10 +148,11 @@ static int __init atstk1004_init(void) at32_add_device_spi(1, spi1_board_info, ARRAY_SIZE(spi1_board_info)); #endif #ifndef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM - at32_add_device_mci(0, NULL); + at32_add_device_mci(0, &mci0_data); #endif at32_add_device_lcdc(0, &atstk1000_lcdc_data, - fbmem_start, fbmem_size, 0); + fbmem_start, fbmem_size, + ATMEL_LCDC_PRI_24BIT | ATMEL_LCDC_PRI_CONTROL); at32_add_device_usba(0, NULL); #ifndef CONFIG_BOARD_ATSTK100X_SW3_CUSTOM at32_add_device_ssc(0, ATMEL_SSC_TX); diff --git a/arch/avr32/boot/images/.gitignore b/arch/avr32/boot/images/.gitignore new file mode 100644 index 0000000..64ea9d0 --- /dev/null +++ b/arch/avr32/boot/images/.gitignore @@ -0,0 +1,4 @@ +uImage +uImage.srec +vmlinux.cso +sfdwarf.log diff --git a/arch/avr32/configs/atngw100_defconfig b/arch/avr32/configs/atngw100_defconfig index 119edb8..54152091 100644 --- a/arch/avr32/configs/atngw100_defconfig +++ b/arch/avr32/configs/atngw100_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.26-rc3 -# Mon May 26 13:30:59 2008 +# Linux kernel version: 2.6.27-rc1 +# Tue Aug 5 16:00:47 2008 # CONFIG_AVR32=y CONFIG_GENERIC_GPIO=y @@ -78,10 +78,16 @@ CONFIG_PROFILING=y CONFIG_OPROFILE=m CONFIG_HAVE_OPROFILE=y CONFIG_KPROBES=y +# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set +# CONFIG_HAVE_IOREMAP_PROT is not set CONFIG_HAVE_KPROBES=y # CONFIG_HAVE_KRETPROBES is not set +# CONFIG_HAVE_ARCH_TRACEHOOK is not set # CONFIG_HAVE_DMA_ATTRS is not set +# CONFIG_USE_GENERIC_SMP_HELPERS is not set +CONFIG_HAVE_CLK=y CONFIG_PROC_PAGE_MONITOR=y +# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y CONFIG_RT_MUTEXES=y # CONFIG_TINY_SHMEM is not set @@ -98,6 +104,7 @@ CONFIG_BLOCK=y # CONFIG_BLK_DEV_IO_TRACE is not set # CONFIG_LSF is not set # CONFIG_BLK_DEV_BSG is not set +# CONFIG_BLK_DEV_INTEGRITY is not set # # IO Schedulers @@ -142,6 +149,7 @@ CONFIG_PHYS_OFFSET=0x10000000 CONFIG_PREEMPT_NONE=y # CONFIG_PREEMPT_VOLUNTARY is not set # CONFIG_PREEMPT is not set +CONFIG_QUICKLIST=y # CONFIG_HAVE_ARCH_BOOTMEM_NODE is not set # CONFIG_ARCH_HAVE_MEMORY_PRESENT is not set # CONFIG_NEED_NODE_MEMMAP_SIZE is not set @@ -160,6 +168,7 @@ CONFIG_PAGEFLAGS_EXTENDED=y CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set CONFIG_ZONE_DMA_FLAG=0 +CONFIG_NR_QUICK=2 CONFIG_VIRT_TO_BUS=y # CONFIG_OWNERSHIP_TRACE is not set CONFIG_NMI_DEBUGGING=y @@ -174,6 +183,12 @@ CONFIG_CMDLINE="" # # Power management options # +CONFIG_PM=y +# CONFIG_PM_DEBUG is not set +CONFIG_PM_SLEEP=y +CONFIG_SUSPEND=y +CONFIG_SUSPEND_FREEZER=y +CONFIG_ARCH_SUSPEND_POSSIBLE=y # # CPU Frequency scaling @@ -205,10 +220,6 @@ CONFIG_CPU_FREQ_AT32AP=y # CONFIG_BINFMT_ELF=y # CONFIG_BINFMT_MISC is not set - -# -# Networking -# CONFIG_NET=y # @@ -222,6 +233,7 @@ CONFIG_XFRM_USER=y # CONFIG_XFRM_SUB_POLICY is not set # CONFIG_XFRM_MIGRATE is not set # CONFIG_XFRM_STATISTICS is not set +CONFIG_XFRM_IPCOMP=y CONFIG_NET_KEY=y # CONFIG_NET_KEY_MIGRATE is not set CONFIG_INET=y @@ -339,8 +351,10 @@ CONFIG_IP6_NF_MANGLE=m # CONFIG_IP_SCTP is not set # CONFIG_TIPC is not set # CONFIG_ATM is not set +CONFIG_STP=m CONFIG_BRIDGE=m CONFIG_VLAN_8021Q=m +# CONFIG_VLAN_8021Q_GVRP is not set # CONFIG_DECNET is not set CONFIG_LLC=m # CONFIG_LLC2 is not set @@ -499,7 +513,6 @@ CONFIG_ATMEL_TCB_CLKSRC_BLOCK=0 # CONFIG_ATA is not set # CONFIG_MD is not set CONFIG_NETDEVICES=y -# CONFIG_NETDEVICES_MULTIQUEUE is not set # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -607,21 +620,35 @@ CONFIG_I2C_ALGOBIT=m # # I2C Hardware Bus support # + +# +# I2C system bus drivers (mostly embedded / system-on-chip) +# CONFIG_I2C_GPIO=m # CONFIG_I2C_OCORES is not set -# CONFIG_I2C_PARPORT_LIGHT is not set # CONFIG_I2C_SIMTEC is not set + +# +# External I2C/SMBus adapter drivers +# +# CONFIG_I2C_PARPORT_LIGHT is not set # CONFIG_I2C_TAOS_EVM is not set -# CONFIG_I2C_STUB is not set + +# +# Other I2C/SMBus bus drivers +# # CONFIG_I2C_PCA_PLATFORM is not set +# CONFIG_I2C_STUB is not set # # Miscellaneous I2C Chip support # # CONFIG_DS1682 is not set +CONFIG_AT24=m # CONFIG_SENSORS_EEPROM is not set # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set +# CONFIG_SENSORS_PCA9539 is not set # CONFIG_SENSORS_PCF8591 is not set # CONFIG_TPS65010 is not set # CONFIG_SENSORS_MAX6875 is not set @@ -646,27 +673,32 @@ CONFIG_SPI_ATMEL=y # CONFIG_SPI_AT25 is not set CONFIG_SPI_SPIDEV=m # CONFIG_SPI_TLE62X0 is not set -CONFIG_HAVE_GPIO_LIB=y - -# -# GPIO Support -# +CONFIG_ARCH_REQUIRE_GPIOLIB=y +CONFIG_GPIOLIB=y # CONFIG_DEBUG_GPIO is not set +CONFIG_GPIO_SYSFS=y # # I2C GPIO expanders: # +# CONFIG_GPIO_MAX732X is not set # CONFIG_GPIO_PCA953X is not set # CONFIG_GPIO_PCF857X is not set # +# PCI GPIO expanders: +# + +# # SPI GPIO expanders: # +# CONFIG_GPIO_MAX7301 is not set # CONFIG_GPIO_MCP23S08 is not set # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set # CONFIG_HWMON is not set # CONFIG_THERMAL is not set +# CONFIG_THERMAL_HWMON is not set CONFIG_WATCHDOG=y # CONFIG_WATCHDOG_NOWAYOUT is not set @@ -685,6 +717,7 @@ CONFIG_SSB_POSSIBLE=y # # Multifunction device drivers # +# CONFIG_MFD_CORE is not set # CONFIG_MFD_SM501 is not set # CONFIG_HTC_PASIC3 is not set @@ -716,10 +749,6 @@ CONFIG_SSB_POSSIBLE=y # Display device support # # CONFIG_DISPLAY_SUPPORT is not set - -# -# Sound -# # CONFIG_SOUND is not set CONFIG_USB_SUPPORT=y # CONFIG_USB_ARCH_HAS_HCD is not set @@ -740,7 +769,7 @@ CONFIG_USB_GADGET_ATMEL_USBA=y CONFIG_USB_ATMEL_USBA=y # CONFIG_USB_GADGET_FSL_USB2 is not set # CONFIG_USB_GADGET_NET2280 is not set -# CONFIG_USB_GADGET_PXA2XX is not set +# CONFIG_USB_GADGET_PXA25X is not set # CONFIG_USB_GADGET_M66592 is not set # CONFIG_USB_GADGET_PXA27X is not set # CONFIG_USB_GADGET_GOKU is not set @@ -759,21 +788,24 @@ CONFIG_USB_FILE_STORAGE=m CONFIG_USB_G_SERIAL=m # CONFIG_USB_MIDI_GADGET is not set # CONFIG_USB_G_PRINTER is not set -CONFIG_MMC=m +CONFIG_USB_CDC_COMPOSITE=m +CONFIG_MMC=y # CONFIG_MMC_DEBUG is not set # CONFIG_MMC_UNSAFE_RESUME is not set # # MMC/SD Card Drivers # -CONFIG_MMC_BLOCK=m +CONFIG_MMC_BLOCK=y CONFIG_MMC_BLOCK_BOUNCE=y # CONFIG_SDIO_UART is not set -# CONFIG_MMC_TEST is not set +CONFIG_MMC_TEST=m # # MMC/SD Host Controller Drivers # +# CONFIG_MMC_SDHCI is not set +CONFIG_MMC_ATMELMCI=y CONFIG_MMC_SPI=m # CONFIG_MEMSTICK is not set CONFIG_NEW_LEDS=y @@ -783,6 +815,7 @@ CONFIG_LEDS_CLASS=y # LED drivers # CONFIG_LEDS_GPIO=y +# CONFIG_LEDS_PCA955X is not set # # LED Triggers @@ -821,10 +854,13 @@ CONFIG_RTC_INTF_DEV=y # CONFIG_RTC_DRV_PCF8583 is not set # CONFIG_RTC_DRV_M41T80 is not set # CONFIG_RTC_DRV_S35390A is not set +# CONFIG_RTC_DRV_FM3130 is not set # # SPI RTC drivers # +# CONFIG_RTC_DRV_M41T94 is not set +# CONFIG_RTC_DRV_DS1305 is not set # CONFIG_RTC_DRV_MAX6902 is not set # CONFIG_RTC_DRV_R9701 is not set # CONFIG_RTC_DRV_RS5C348 is not set @@ -844,6 +880,19 @@ CONFIG_RTC_INTF_DEV=y # on-CPU RTC drivers # CONFIG_RTC_DRV_AT32AP700X=y +CONFIG_DMADEVICES=y + +# +# DMA Devices +# +CONFIG_DW_DMAC=y +CONFIG_DMA_ENGINE=y + +# +# DMA Clients +# +# CONFIG_NET_DMA is not set +CONFIG_DMATEST=m # CONFIG_UIO is not set # @@ -921,6 +970,7 @@ CONFIG_JFFS2_RTIME=y # CONFIG_CRAMFS is not set # CONFIG_VXFS_FS is not set # CONFIG_MINIX_FS is not set +# CONFIG_OMFS_FS is not set # CONFIG_HPFS_FS is not set # CONFIG_QNX4FS_FS is not set # CONFIG_ROMFS_FS is not set @@ -931,17 +981,16 @@ CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set # CONFIG_NFS_V4 is not set +CONFIG_ROOT_NFS=y CONFIG_NFSD=m CONFIG_NFSD_V3=y # CONFIG_NFSD_V3_ACL is not set # CONFIG_NFSD_V4 is not set -CONFIG_ROOT_NFS=y CONFIG_LOCKD=y CONFIG_LOCKD_V4=y CONFIG_EXPORTFS=m CONFIG_NFS_COMMON=y CONFIG_SUNRPC=y -# CONFIG_SUNRPC_BIND34 is not set # CONFIG_RPCSEC_GSS_KRB5 is not set # CONFIG_RPCSEC_GSS_SPKM3 is not set CONFIG_SMB_FS=m @@ -1017,6 +1066,8 @@ CONFIG_MAGIC_SYSRQ=y CONFIG_DEBUG_KERNEL=y # CONFIG_DEBUG_SHIRQ is not set CONFIG_DETECT_SOFTLOCKUP=y +# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set +CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0 CONFIG_SCHED_DEBUG=y # CONFIG_SCHEDSTATS is not set # CONFIG_TIMER_STATS is not set @@ -1037,6 +1088,7 @@ CONFIG_DEBUG_BUGVERBOSE=y # CONFIG_DEBUG_INFO is not set # CONFIG_DEBUG_VM is not set # CONFIG_DEBUG_WRITECOUNT is not set +# CONFIG_DEBUG_MEMORY_INIT is not set # CONFIG_DEBUG_LIST is not set # CONFIG_DEBUG_SG is not set CONFIG_FRAME_POINTER=y @@ -1101,6 +1153,10 @@ CONFIG_CRYPTO_HMAC=y # CONFIG_CRYPTO_MD4 is not set CONFIG_CRYPTO_MD5=y # CONFIG_CRYPTO_MICHAEL_MIC is not set +# CONFIG_CRYPTO_RMD128 is not set +# CONFIG_CRYPTO_RMD160 is not set +# CONFIG_CRYPTO_RMD256 is not set +# CONFIG_CRYPTO_RMD320 is not set CONFIG_CRYPTO_SHA1=y # CONFIG_CRYPTO_SHA256 is not set # CONFIG_CRYPTO_SHA512 is not set @@ -1141,12 +1197,14 @@ CONFIG_BITREVERSE=y # CONFIG_GENERIC_FIND_NEXT_BIT is not set CONFIG_CRC_CCITT=m # CONFIG_CRC16 is not set +# CONFIG_CRC_T10DIF is not set CONFIG_CRC_ITU_T=m CONFIG_CRC32=y CONFIG_CRC7=m # CONFIG_LIBCRC32C is not set CONFIG_ZLIB_INFLATE=y CONFIG_ZLIB_DEFLATE=y +CONFIG_GENERIC_ALLOCATOR=y CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y diff --git a/arch/avr32/configs/atstk1002_defconfig b/arch/avr32/configs/atstk1002_defconfig index c6d02ea..69fce6b 100644 --- a/arch/avr32/configs/atstk1002_defconfig +++ b/arch/avr32/configs/atstk1002_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.26-rc3 -# Mon May 26 13:30:20 2008 +# Linux kernel version: 2.6.27-rc1 +# Mon Aug 4 16:02:27 2008 # CONFIG_AVR32=y CONFIG_GENERIC_GPIO=y @@ -77,10 +77,16 @@ CONFIG_PROFILING=y CONFIG_OPROFILE=m CONFIG_HAVE_OPROFILE=y CONFIG_KPROBES=y +# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set +# CONFIG_HAVE_IOREMAP_PROT is not set CONFIG_HAVE_KPROBES=y # CONFIG_HAVE_KRETPROBES is not set +# CONFIG_HAVE_ARCH_TRACEHOOK is not set # CONFIG_HAVE_DMA_ATTRS is not set +# CONFIG_USE_GENERIC_SMP_HELPERS is not set +CONFIG_HAVE_CLK=y CONFIG_PROC_PAGE_MONITOR=y +# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y CONFIG_RT_MUTEXES=y # CONFIG_TINY_SHMEM is not set @@ -91,12 +97,13 @@ CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set -# CONFIG_KMOD is not set +CONFIG_KMOD=y CONFIG_BLOCK=y # CONFIG_LBD is not set # CONFIG_BLK_DEV_IO_TRACE is not set # CONFIG_LSF is not set # CONFIG_BLK_DEV_BSG is not set +# CONFIG_BLK_DEV_INTEGRITY is not set # # IO Schedulers @@ -130,6 +137,7 @@ CONFIG_BOARD_ATSTK1000=y CONFIG_BOARD_ATSTK1002=y # CONFIG_BOARD_ATSTK1003 is not set # CONFIG_BOARD_ATSTK1004 is not set +# CONFIG_BOARD_ATSTK1006 is not set # CONFIG_BOARD_ATSTK100X_CUSTOM is not set # CONFIG_BOARD_ATSTK100X_SPI1 is not set # CONFIG_BOARD_ATSTK1000_J2_LED is not set @@ -150,6 +158,7 @@ CONFIG_PHYS_OFFSET=0x10000000 CONFIG_PREEMPT_NONE=y # CONFIG_PREEMPT_VOLUNTARY is not set # CONFIG_PREEMPT is not set +CONFIG_QUICKLIST=y # CONFIG_HAVE_ARCH_BOOTMEM_NODE is not set # CONFIG_ARCH_HAVE_MEMORY_PRESENT is not set # CONFIG_NEED_NODE_MEMMAP_SIZE is not set @@ -168,6 +177,7 @@ CONFIG_PAGEFLAGS_EXTENDED=y CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set CONFIG_ZONE_DMA_FLAG=0 +CONFIG_NR_QUICK=2 CONFIG_VIRT_TO_BUS=y # CONFIG_OWNERSHIP_TRACE is not set CONFIG_NMI_DEBUGGING=y @@ -182,6 +192,12 @@ CONFIG_CMDLINE="" # # Power management options # +CONFIG_PM=y +# CONFIG_PM_DEBUG is not set +CONFIG_PM_SLEEP=y +CONFIG_SUSPEND=y +CONFIG_SUSPEND_FREEZER=y +CONFIG_ARCH_SUSPEND_POSSIBLE=y # # CPU Frequency scaling @@ -213,10 +229,6 @@ CONFIG_CPU_FREQ_AT32AP=y # CONFIG_BINFMT_ELF=y # CONFIG_BINFMT_MISC is not set - -# -# Networking -# CONFIG_NET=y # @@ -230,6 +242,7 @@ CONFIG_XFRM_USER=m # CONFIG_XFRM_SUB_POLICY is not set # CONFIG_XFRM_MIGRATE is not set # CONFIG_XFRM_STATISTICS is not set +CONFIG_XFRM_IPCOMP=m CONFIG_NET_KEY=m # CONFIG_NET_KEY_MIGRATE is not set CONFIG_INET=y @@ -284,6 +297,7 @@ CONFIG_IPV6_TUNNEL=m # CONFIG_IP_SCTP is not set # CONFIG_TIPC is not set # CONFIG_ATM is not set +CONFIG_STP=m CONFIG_BRIDGE=m # CONFIG_VLAN_8021Q is not set # CONFIG_DECNET is not set @@ -474,6 +488,7 @@ CONFIG_SCSI_WAIT_SCAN=m # CONFIG_SCSI_SAS_LIBSAS is not set # CONFIG_SCSI_SRP_ATTRS is not set # CONFIG_SCSI_LOWLEVEL is not set +# CONFIG_SCSI_DH is not set CONFIG_ATA=m # CONFIG_ATA_NONSTANDARD is not set # CONFIG_SATA_PMP is not set @@ -483,7 +498,6 @@ CONFIG_PATA_AT32=m # CONFIG_PATA_PLATFORM is not set # CONFIG_MD is not set CONFIG_NETDEVICES=y -# CONFIG_NETDEVICES_MULTIQUEUE is not set # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -625,21 +639,35 @@ CONFIG_I2C_ALGOBIT=m # # I2C Hardware Bus support # + +# +# I2C system bus drivers (mostly embedded / system-on-chip) +# CONFIG_I2C_GPIO=m # CONFIG_I2C_OCORES is not set -# CONFIG_I2C_PARPORT_LIGHT is not set # CONFIG_I2C_SIMTEC is not set + +# +# External I2C/SMBus adapter drivers +# +# CONFIG_I2C_PARPORT_LIGHT is not set # CONFIG_I2C_TAOS_EVM is not set -# CONFIG_I2C_STUB is not set + +# +# Other I2C/SMBus bus drivers +# # CONFIG_I2C_PCA_PLATFORM is not set +# CONFIG_I2C_STUB is not set # # Miscellaneous I2C Chip support # # CONFIG_DS1682 is not set +CONFIG_AT24=m # CONFIG_SENSORS_EEPROM is not set # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set +# CONFIG_SENSORS_PCA9539 is not set # CONFIG_SENSORS_PCF8591 is not set # CONFIG_TPS65010 is not set # CONFIG_SENSORS_MAX6875 is not set @@ -664,27 +692,32 @@ CONFIG_SPI_ATMEL=y # CONFIG_SPI_AT25 is not set CONFIG_SPI_SPIDEV=m # CONFIG_SPI_TLE62X0 is not set -CONFIG_HAVE_GPIO_LIB=y - -# -# GPIO Support -# +CONFIG_ARCH_REQUIRE_GPIOLIB=y +CONFIG_GPIOLIB=y # CONFIG_DEBUG_GPIO is not set +CONFIG_GPIO_SYSFS=y # # I2C GPIO expanders: # +# CONFIG_GPIO_MAX732X is not set # CONFIG_GPIO_PCA953X is not set # CONFIG_GPIO_PCF857X is not set # +# PCI GPIO expanders: +# + +# # SPI GPIO expanders: # +# CONFIG_GPIO_MAX7301 is not set # CONFIG_GPIO_MCP23S08 is not set # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set # CONFIG_HWMON is not set # CONFIG_THERMAL is not set +# CONFIG_THERMAL_HWMON is not set CONFIG_WATCHDOG=y # CONFIG_WATCHDOG_NOWAYOUT is not set @@ -703,6 +736,7 @@ CONFIG_SSB_POSSIBLE=y # # Multifunction device drivers # +# CONFIG_MFD_CORE is not set # CONFIG_MFD_SM501 is not set # CONFIG_HTC_PASIC3 is not set @@ -754,6 +788,9 @@ CONFIG_FB_ATMEL=y CONFIG_BACKLIGHT_LCD_SUPPORT=y CONFIG_LCD_CLASS_DEVICE=y CONFIG_LCD_LTV350QV=y +# CONFIG_LCD_ILI9320 is not set +# CONFIG_LCD_VGG2432A4 is not set +# CONFIG_LCD_PLATFORM is not set # CONFIG_BACKLIGHT_CLASS_DEVICE is not set # @@ -761,15 +798,7 @@ CONFIG_LCD_LTV350QV=y # # CONFIG_DISPLAY_SUPPORT is not set # CONFIG_LOGO is not set - -# -# Sound -# CONFIG_SOUND=m - -# -# Advanced Linux Sound Architecture -# CONFIG_SND=m CONFIG_SND_TIMER=m CONFIG_SND_PCM=m @@ -783,37 +812,11 @@ CONFIG_SND_PCM_OSS_PLUGINS=y # CONFIG_SND_VERBOSE_PROCFS is not set # CONFIG_SND_VERBOSE_PRINTK is not set # CONFIG_SND_DEBUG is not set - -# -# Generic devices -# -# CONFIG_SND_DUMMY is not set -# CONFIG_SND_MTPAV is not set -# CONFIG_SND_SERIAL_U16550 is not set -# CONFIG_SND_MPU401 is not set - -# -# SPI devices -# +# CONFIG_SND_DRIVERS is not set +CONFIG_SND_SPI=y CONFIG_SND_AT73C213=m CONFIG_SND_AT73C213_TARGET_BITRATE=48000 - -# -# System on Chip audio support -# # CONFIG_SND_SOC is not set - -# -# ALSA SoC audio for Freescale SOCs -# - -# -# SoC Audio for the Texas Instruments OMAP -# - -# -# Open Sound System -# # CONFIG_SOUND_PRIME is not set # CONFIG_HID_SUPPORT is not set CONFIG_USB_SUPPORT=y @@ -836,7 +839,7 @@ CONFIG_USB_GADGET_ATMEL_USBA=y CONFIG_USB_ATMEL_USBA=y # CONFIG_USB_GADGET_FSL_USB2 is not set # CONFIG_USB_GADGET_NET2280 is not set -# CONFIG_USB_GADGET_PXA2XX is not set +# CONFIG_USB_GADGET_PXA25X is not set # CONFIG_USB_GADGET_M66592 is not set # CONFIG_USB_GADGET_PXA27X is not set # CONFIG_USB_GADGET_GOKU is not set @@ -855,21 +858,24 @@ CONFIG_USB_FILE_STORAGE=m CONFIG_USB_G_SERIAL=m # CONFIG_USB_MIDI_GADGET is not set # CONFIG_USB_G_PRINTER is not set -CONFIG_MMC=m +CONFIG_USB_CDC_COMPOSITE=m +CONFIG_MMC=y # CONFIG_MMC_DEBUG is not set # CONFIG_MMC_UNSAFE_RESUME is not set # # MMC/SD Card Drivers # -CONFIG_MMC_BLOCK=m +CONFIG_MMC_BLOCK=y CONFIG_MMC_BLOCK_BOUNCE=y # CONFIG_SDIO_UART is not set -CONFIG_MMC_TEST=m +# CONFIG_MMC_TEST is not set # # MMC/SD Host Controller Drivers # +# CONFIG_MMC_SDHCI is not set +CONFIG_MMC_ATMELMCI=y CONFIG_MMC_SPI=m # CONFIG_MEMSTICK is not set CONFIG_NEW_LEDS=y @@ -879,7 +885,9 @@ CONFIG_LEDS_CLASS=m # LED drivers # CONFIG_LEDS_ATMEL_PWM=m +# CONFIG_LEDS_PCA9532 is not set CONFIG_LEDS_GPIO=m +# CONFIG_LEDS_PCA955X is not set # # LED Triggers @@ -918,10 +926,13 @@ CONFIG_RTC_INTF_DEV=y # CONFIG_RTC_DRV_PCF8583 is not set # CONFIG_RTC_DRV_M41T80 is not set # CONFIG_RTC_DRV_S35390A is not set +# CONFIG_RTC_DRV_FM3130 is not set # # SPI RTC drivers # +# CONFIG_RTC_DRV_M41T94 is not set +# CONFIG_RTC_DRV_DS1305 is not set # CONFIG_RTC_DRV_MAX6902 is not set # CONFIG_RTC_DRV_R9701 is not set # CONFIG_RTC_DRV_RS5C348 is not set @@ -941,18 +952,31 @@ CONFIG_RTC_INTF_DEV=y # on-CPU RTC drivers # CONFIG_RTC_DRV_AT32AP700X=y +CONFIG_DMADEVICES=y + +# +# DMA Devices +# +CONFIG_DW_DMAC=y +CONFIG_DMA_ENGINE=y + +# +# DMA Clients +# +# CONFIG_NET_DMA is not set +CONFIG_DMATEST=m # CONFIG_UIO is not set # # File systems # -CONFIG_EXT2_FS=m +CONFIG_EXT2_FS=y # CONFIG_EXT2_FS_XATTR is not set # CONFIG_EXT2_FS_XIP is not set -CONFIG_EXT3_FS=m +CONFIG_EXT3_FS=y # CONFIG_EXT3_FS_XATTR is not set # CONFIG_EXT4DEV_FS is not set -CONFIG_JBD=m +CONFIG_JBD=y # CONFIG_JBD_DEBUG is not set # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set @@ -1018,6 +1042,7 @@ CONFIG_JFFS2_RTIME=y # CONFIG_CRAMFS is not set # CONFIG_VXFS_FS is not set CONFIG_MINIX_FS=m +# CONFIG_OMFS_FS is not set # CONFIG_HPFS_FS is not set # CONFIG_QNX4FS_FS is not set # CONFIG_ROMFS_FS is not set @@ -1028,13 +1053,12 @@ CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set # CONFIG_NFS_V4 is not set -# CONFIG_NFSD is not set CONFIG_ROOT_NFS=y +# CONFIG_NFSD is not set CONFIG_LOCKD=y CONFIG_LOCKD_V4=y CONFIG_NFS_COMMON=y CONFIG_SUNRPC=y -# CONFIG_SUNRPC_BIND34 is not set # CONFIG_RPCSEC_GSS_KRB5 is not set # CONFIG_RPCSEC_GSS_SPKM3 is not set # CONFIG_SMB_FS is not set @@ -1104,6 +1128,8 @@ CONFIG_DEBUG_FS=y CONFIG_DEBUG_KERNEL=y # CONFIG_DEBUG_SHIRQ is not set CONFIG_DETECT_SOFTLOCKUP=y +# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set +CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0 CONFIG_SCHED_DEBUG=y # CONFIG_SCHEDSTATS is not set # CONFIG_TIMER_STATS is not set @@ -1124,6 +1150,7 @@ CONFIG_DEBUG_BUGVERBOSE=y # CONFIG_DEBUG_INFO is not set # CONFIG_DEBUG_VM is not set # CONFIG_DEBUG_WRITECOUNT is not set +# CONFIG_DEBUG_MEMORY_INIT is not set # CONFIG_DEBUG_LIST is not set # CONFIG_DEBUG_SG is not set CONFIG_FRAME_POINTER=y @@ -1188,6 +1215,10 @@ CONFIG_CRYPTO_HMAC=m # CONFIG_CRYPTO_MD4 is not set CONFIG_CRYPTO_MD5=m # CONFIG_CRYPTO_MICHAEL_MIC is not set +# CONFIG_CRYPTO_RMD128 is not set +# CONFIG_CRYPTO_RMD160 is not set +# CONFIG_CRYPTO_RMD256 is not set +# CONFIG_CRYPTO_RMD320 is not set CONFIG_CRYPTO_SHA1=m # CONFIG_CRYPTO_SHA256 is not set # CONFIG_CRYPTO_SHA512 is not set @@ -1228,12 +1259,14 @@ CONFIG_BITREVERSE=y # CONFIG_GENERIC_FIND_NEXT_BIT is not set CONFIG_CRC_CCITT=m # CONFIG_CRC16 is not set +CONFIG_CRC_T10DIF=m CONFIG_CRC_ITU_T=m CONFIG_CRC32=y CONFIG_CRC7=m # CONFIG_LIBCRC32C is not set CONFIG_ZLIB_INFLATE=y CONFIG_ZLIB_DEFLATE=y +CONFIG_GENERIC_ALLOCATOR=y CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y diff --git a/arch/avr32/configs/atstk1003_defconfig b/arch/avr32/configs/atstk1003_defconfig index 5a4ae6b..5477ed3 100644 --- a/arch/avr32/configs/atstk1003_defconfig +++ b/arch/avr32/configs/atstk1003_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.26-rc3 -# Mon May 26 13:33:05 2008 +# Linux kernel version: 2.6.27-rc1 +# Tue Aug 5 15:34:44 2008 # CONFIG_AVR32=y CONFIG_GENERIC_GPIO=y @@ -80,10 +80,16 @@ CONFIG_PROFILING=y CONFIG_OPROFILE=m CONFIG_HAVE_OPROFILE=y CONFIG_KPROBES=y +# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set +# CONFIG_HAVE_IOREMAP_PROT is not set CONFIG_HAVE_KPROBES=y # CONFIG_HAVE_KRETPROBES is not set +# CONFIG_HAVE_ARCH_TRACEHOOK is not set # CONFIG_HAVE_DMA_ATTRS is not set +# CONFIG_USE_GENERIC_SMP_HELPERS is not set +CONFIG_HAVE_CLK=y CONFIG_PROC_PAGE_MONITOR=y +# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_RT_MUTEXES=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=1 @@ -93,12 +99,13 @@ CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set -# CONFIG_KMOD is not set +CONFIG_KMOD=y CONFIG_BLOCK=y # CONFIG_LBD is not set # CONFIG_BLK_DEV_IO_TRACE is not set # CONFIG_LSF is not set # CONFIG_BLK_DEV_BSG is not set +# CONFIG_BLK_DEV_INTEGRITY is not set # # IO Schedulers @@ -132,6 +139,7 @@ CONFIG_BOARD_ATSTK1000=y # CONFIG_BOARD_ATSTK1002 is not set CONFIG_BOARD_ATSTK1003=y # CONFIG_BOARD_ATSTK1004 is not set +# CONFIG_BOARD_ATSTK1006 is not set # CONFIG_BOARD_ATSTK100X_CUSTOM is not set # CONFIG_BOARD_ATSTK100X_SPI1 is not set # CONFIG_BOARD_ATSTK1000_J2_LED is not set @@ -152,6 +160,7 @@ CONFIG_PHYS_OFFSET=0x10000000 CONFIG_PREEMPT_NONE=y # CONFIG_PREEMPT_VOLUNTARY is not set # CONFIG_PREEMPT is not set +CONFIG_QUICKLIST=y # CONFIG_HAVE_ARCH_BOOTMEM_NODE is not set # CONFIG_ARCH_HAVE_MEMORY_PRESENT is not set # CONFIG_NEED_NODE_MEMMAP_SIZE is not set @@ -170,6 +179,7 @@ CONFIG_PAGEFLAGS_EXTENDED=y CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set CONFIG_ZONE_DMA_FLAG=0 +CONFIG_NR_QUICK=2 CONFIG_VIRT_TO_BUS=y # CONFIG_OWNERSHIP_TRACE is not set CONFIG_NMI_DEBUGGING=y @@ -184,6 +194,12 @@ CONFIG_CMDLINE="" # # Power management options # +CONFIG_PM=y +# CONFIG_PM_DEBUG is not set +CONFIG_PM_SLEEP=y +CONFIG_SUSPEND=y +CONFIG_SUSPEND_FREEZER=y +CONFIG_ARCH_SUSPEND_POSSIBLE=y # # CPU Frequency scaling @@ -215,10 +231,6 @@ CONFIG_CPU_FREQ_AT32AP=y # CONFIG_BINFMT_ELF=y # CONFIG_BINFMT_MISC is not set - -# -# Networking -# CONFIG_NET=y # @@ -449,6 +461,7 @@ CONFIG_SCSI_WAIT_SCAN=m CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_SCSI_DEBUG is not set +# CONFIG_SCSI_DH is not set CONFIG_ATA=m # CONFIG_ATA_NONSTANDARD is not set # CONFIG_SATA_PMP is not set @@ -458,7 +471,6 @@ CONFIG_PATA_AT32=m # CONFIG_PATA_PLATFORM is not set # CONFIG_MD is not set CONFIG_NETDEVICES=y -# CONFIG_NETDEVICES_MULTIQUEUE is not set # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -575,21 +587,35 @@ CONFIG_I2C_ALGOBIT=m # # I2C Hardware Bus support # + +# +# I2C system bus drivers (mostly embedded / system-on-chip) +# CONFIG_I2C_GPIO=m # CONFIG_I2C_OCORES is not set -# CONFIG_I2C_PARPORT_LIGHT is not set # CONFIG_I2C_SIMTEC is not set + +# +# External I2C/SMBus adapter drivers +# +# CONFIG_I2C_PARPORT_LIGHT is not set # CONFIG_I2C_TAOS_EVM is not set -# CONFIG_I2C_STUB is not set + +# +# Other I2C/SMBus bus drivers +# # CONFIG_I2C_PCA_PLATFORM is not set +# CONFIG_I2C_STUB is not set # # Miscellaneous I2C Chip support # # CONFIG_DS1682 is not set +CONFIG_AT24=m # CONFIG_SENSORS_EEPROM is not set # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set +# CONFIG_SENSORS_PCA9539 is not set # CONFIG_SENSORS_PCF8591 is not set # CONFIG_TPS65010 is not set # CONFIG_SENSORS_MAX6875 is not set @@ -614,27 +640,32 @@ CONFIG_SPI_ATMEL=y # CONFIG_SPI_AT25 is not set CONFIG_SPI_SPIDEV=m # CONFIG_SPI_TLE62X0 is not set -CONFIG_HAVE_GPIO_LIB=y - -# -# GPIO Support -# +CONFIG_ARCH_REQUIRE_GPIOLIB=y +CONFIG_GPIOLIB=y # CONFIG_DEBUG_GPIO is not set +CONFIG_GPIO_SYSFS=y # # I2C GPIO expanders: # +# CONFIG_GPIO_MAX732X is not set # CONFIG_GPIO_PCA953X is not set # CONFIG_GPIO_PCF857X is not set # +# PCI GPIO expanders: +# + +# # SPI GPIO expanders: # +# CONFIG_GPIO_MAX7301 is not set # CONFIG_GPIO_MCP23S08 is not set # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set # CONFIG_HWMON is not set # CONFIG_THERMAL is not set +# CONFIG_THERMAL_HWMON is not set CONFIG_WATCHDOG=y # CONFIG_WATCHDOG_NOWAYOUT is not set @@ -653,6 +684,7 @@ CONFIG_SSB_POSSIBLE=y # # Multifunction device drivers # +# CONFIG_MFD_CORE is not set # CONFIG_MFD_SM501 is not set # CONFIG_HTC_PASIC3 is not set @@ -684,15 +716,7 @@ CONFIG_SSB_POSSIBLE=y # Display device support # # CONFIG_DISPLAY_SUPPORT is not set - -# -# Sound -# CONFIG_SOUND=m - -# -# Advanced Linux Sound Architecture -# CONFIG_SND=m CONFIG_SND_TIMER=m CONFIG_SND_PCM=m @@ -706,37 +730,11 @@ CONFIG_SND_SUPPORT_OLD_API=y CONFIG_SND_VERBOSE_PROCFS=y # CONFIG_SND_VERBOSE_PRINTK is not set # CONFIG_SND_DEBUG is not set - -# -# Generic devices -# -# CONFIG_SND_DUMMY is not set -# CONFIG_SND_MTPAV is not set -# CONFIG_SND_SERIAL_U16550 is not set -# CONFIG_SND_MPU401 is not set - -# -# SPI devices -# +# CONFIG_SND_DRIVERS is not set +CONFIG_SND_SPI=y CONFIG_SND_AT73C213=m CONFIG_SND_AT73C213_TARGET_BITRATE=48000 - -# -# System on Chip audio support -# # CONFIG_SND_SOC is not set - -# -# ALSA SoC audio for Freescale SOCs -# - -# -# SoC Audio for the Texas Instruments OMAP -# - -# -# Open Sound System -# # CONFIG_SOUND_PRIME is not set # CONFIG_HID_SUPPORT is not set CONFIG_USB_SUPPORT=y @@ -759,7 +757,7 @@ CONFIG_USB_GADGET_ATMEL_USBA=y CONFIG_USB_ATMEL_USBA=y # CONFIG_USB_GADGET_FSL_USB2 is not set # CONFIG_USB_GADGET_NET2280 is not set -# CONFIG_USB_GADGET_PXA2XX is not set +# CONFIG_USB_GADGET_PXA25X is not set # CONFIG_USB_GADGET_M66592 is not set # CONFIG_USB_GADGET_PXA27X is not set # CONFIG_USB_GADGET_GOKU is not set @@ -778,21 +776,24 @@ CONFIG_USB_FILE_STORAGE=m CONFIG_USB_G_SERIAL=m # CONFIG_USB_MIDI_GADGET is not set # CONFIG_USB_G_PRINTER is not set -CONFIG_MMC=m +CONFIG_USB_CDC_COMPOSITE=m +CONFIG_MMC=y # CONFIG_MMC_DEBUG is not set # CONFIG_MMC_UNSAFE_RESUME is not set # # MMC/SD Card Drivers # -CONFIG_MMC_BLOCK=m -# CONFIG_MMC_BLOCK_BOUNCE is not set +CONFIG_MMC_BLOCK=y +CONFIG_MMC_BLOCK_BOUNCE=y # CONFIG_SDIO_UART is not set -# CONFIG_MMC_TEST is not set +CONFIG_MMC_TEST=m # # MMC/SD Host Controller Drivers # +# CONFIG_MMC_SDHCI is not set +CONFIG_MMC_ATMELMCI=y CONFIG_MMC_SPI=m # CONFIG_MEMSTICK is not set CONFIG_NEW_LEDS=y @@ -802,7 +803,9 @@ CONFIG_LEDS_CLASS=y # LED drivers # CONFIG_LEDS_ATMEL_PWM=m +# CONFIG_LEDS_PCA9532 is not set CONFIG_LEDS_GPIO=y +# CONFIG_LEDS_PCA955X is not set # # LED Triggers @@ -841,10 +844,13 @@ CONFIG_RTC_INTF_DEV=y # CONFIG_RTC_DRV_PCF8583 is not set # CONFIG_RTC_DRV_M41T80 is not set # CONFIG_RTC_DRV_S35390A is not set +# CONFIG_RTC_DRV_FM3130 is not set # # SPI RTC drivers # +# CONFIG_RTC_DRV_M41T94 is not set +# CONFIG_RTC_DRV_DS1305 is not set # CONFIG_RTC_DRV_MAX6902 is not set # CONFIG_RTC_DRV_R9701 is not set # CONFIG_RTC_DRV_RS5C348 is not set @@ -864,8 +870,20 @@ CONFIG_RTC_INTF_DEV=y # on-CPU RTC drivers # CONFIG_RTC_DRV_AT32AP700X=y -CONFIG_UIO=m -# CONFIG_UIO_SMX is not set +CONFIG_DMADEVICES=y + +# +# DMA Devices +# +CONFIG_DW_DMAC=y +CONFIG_DMA_ENGINE=y + +# +# DMA Clients +# +# CONFIG_NET_DMA is not set +CONFIG_DMATEST=m +# CONFIG_UIO is not set # # File systems @@ -943,6 +961,7 @@ CONFIG_JFFS2_RTIME=y # CONFIG_CRAMFS is not set # CONFIG_VXFS_FS is not set # CONFIG_MINIX_FS is not set +# CONFIG_OMFS_FS is not set # CONFIG_HPFS_FS is not set # CONFIG_QNX4FS_FS is not set # CONFIG_ROMFS_FS is not set @@ -1011,6 +1030,8 @@ CONFIG_DEBUG_FS=y CONFIG_DEBUG_KERNEL=y # CONFIG_DEBUG_SHIRQ is not set CONFIG_DETECT_SOFTLOCKUP=y +# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set +CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0 CONFIG_SCHED_DEBUG=y # CONFIG_SCHEDSTATS is not set # CONFIG_TIMER_STATS is not set @@ -1029,6 +1050,7 @@ CONFIG_DEBUG_BUGVERBOSE=y # CONFIG_DEBUG_INFO is not set # CONFIG_DEBUG_VM is not set # CONFIG_DEBUG_WRITECOUNT is not set +# CONFIG_DEBUG_MEMORY_INIT is not set # CONFIG_DEBUG_LIST is not set # CONFIG_DEBUG_SG is not set CONFIG_FRAME_POINTER=y @@ -1056,6 +1078,7 @@ CONFIG_BITREVERSE=y # CONFIG_GENERIC_FIND_NEXT_BIT is not set CONFIG_CRC_CCITT=m # CONFIG_CRC16 is not set +CONFIG_CRC_T10DIF=m CONFIG_CRC_ITU_T=m CONFIG_CRC32=y CONFIG_CRC7=m @@ -1063,6 +1086,7 @@ CONFIG_CRC7=m CONFIG_AUDIT_GENERIC=y CONFIG_ZLIB_INFLATE=y CONFIG_ZLIB_DEFLATE=y +CONFIG_GENERIC_ALLOCATOR=y CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y diff --git a/arch/avr32/configs/atstk1004_defconfig b/arch/avr32/configs/atstk1004_defconfig index a0912fb..69e6c0d 100644 --- a/arch/avr32/configs/atstk1004_defconfig +++ b/arch/avr32/configs/atstk1004_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.26-rc3 -# Mon May 26 13:34:57 2008 +# Linux kernel version: 2.6.27-rc1 +# Tue Aug 5 15:38:56 2008 # CONFIG_AVR32=y CONFIG_GENERIC_GPIO=y @@ -69,10 +69,16 @@ CONFIG_SLOB=y # CONFIG_PROFILING is not set # CONFIG_MARKERS is not set CONFIG_HAVE_OPROFILE=y +# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set +# CONFIG_HAVE_IOREMAP_PROT is not set CONFIG_HAVE_KPROBES=y # CONFIG_HAVE_KRETPROBES is not set +# CONFIG_HAVE_ARCH_TRACEHOOK is not set # CONFIG_HAVE_DMA_ATTRS is not set +# CONFIG_USE_GENERIC_SMP_HELPERS is not set +CONFIG_HAVE_CLK=y # CONFIG_PROC_PAGE_MONITOR is not set +# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=1 # CONFIG_MODULES is not set @@ -97,6 +103,7 @@ CONFIG_BOARD_ATSTK1000=y # CONFIG_BOARD_ATSTK1002 is not set # CONFIG_BOARD_ATSTK1003 is not set CONFIG_BOARD_ATSTK1004=y +# CONFIG_BOARD_ATSTK1006 is not set # CONFIG_BOARD_ATSTK100X_CUSTOM is not set # CONFIG_BOARD_ATSTK100X_SPI1 is not set # CONFIG_BOARD_ATSTK1000_J2_LED is not set @@ -115,6 +122,7 @@ CONFIG_PHYS_OFFSET=0x10000000 CONFIG_PREEMPT_NONE=y # CONFIG_PREEMPT_VOLUNTARY is not set # CONFIG_PREEMPT is not set +CONFIG_QUICKLIST=y # CONFIG_HAVE_ARCH_BOOTMEM_NODE is not set # CONFIG_ARCH_HAVE_MEMORY_PRESENT is not set # CONFIG_NEED_NODE_MEMMAP_SIZE is not set @@ -133,6 +141,7 @@ CONFIG_PAGEFLAGS_EXTENDED=y CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set CONFIG_ZONE_DMA_FLAG=0 +CONFIG_NR_QUICK=2 CONFIG_VIRT_TO_BUS=y # CONFIG_OWNERSHIP_TRACE is not set # CONFIG_NMI_DEBUGGING is not set @@ -147,6 +156,8 @@ CONFIG_CMDLINE="" # # Power management options # +# CONFIG_PM is not set +CONFIG_ARCH_SUSPEND_POSSIBLE=y # # CPU Frequency scaling @@ -164,10 +175,6 @@ CONFIG_CMDLINE="" # CONFIG_BINFMT_ELF=y # CONFIG_BINFMT_MISC is not set - -# -# Networking -# CONFIG_NET=y # @@ -390,24 +397,28 @@ CONFIG_SPI_ATMEL=y # CONFIG_SPI_AT25 is not set # CONFIG_SPI_SPIDEV is not set # CONFIG_SPI_TLE62X0 is not set -CONFIG_HAVE_GPIO_LIB=y +CONFIG_ARCH_REQUIRE_GPIOLIB=y +CONFIG_GPIOLIB=y +# CONFIG_GPIO_SYSFS is not set # -# GPIO Support +# I2C GPIO expanders: # # -# I2C GPIO expanders: +# PCI GPIO expanders: # # # SPI GPIO expanders: # +# CONFIG_GPIO_MAX7301 is not set # CONFIG_GPIO_MCP23S08 is not set # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set # CONFIG_HWMON is not set # CONFIG_THERMAL is not set +# CONFIG_THERMAL_HWMON is not set CONFIG_WATCHDOG=y # CONFIG_WATCHDOG_NOWAYOUT is not set @@ -426,6 +437,7 @@ CONFIG_SSB_POSSIBLE=y # # Multifunction device drivers # +# CONFIG_MFD_CORE is not set # CONFIG_MFD_SM501 is not set # CONFIG_HTC_PASIC3 is not set @@ -477,6 +489,9 @@ CONFIG_FB_ATMEL=y CONFIG_BACKLIGHT_LCD_SUPPORT=y CONFIG_LCD_CLASS_DEVICE=y CONFIG_LCD_LTV350QV=y +# CONFIG_LCD_ILI9320 is not set +# CONFIG_LCD_VGG2432A4 is not set +# CONFIG_LCD_PLATFORM is not set # CONFIG_BACKLIGHT_CLASS_DEVICE is not set # @@ -484,10 +499,6 @@ CONFIG_LCD_LTV350QV=y # # CONFIG_DISPLAY_SUPPORT is not set # CONFIG_LOGO is not set - -# -# Sound -# # CONFIG_SOUND is not set CONFIG_USB_SUPPORT=y # CONFIG_USB_ARCH_HAS_HCD is not set @@ -507,7 +518,7 @@ CONFIG_USB_GADGET_ATMEL_USBA=y CONFIG_USB_ATMEL_USBA=y # CONFIG_USB_GADGET_FSL_USB2 is not set # CONFIG_USB_GADGET_NET2280 is not set -# CONFIG_USB_GADGET_PXA2XX is not set +# CONFIG_USB_GADGET_PXA25X is not set # CONFIG_USB_GADGET_M66592 is not set # CONFIG_USB_GADGET_PXA27X is not set # CONFIG_USB_GADGET_GOKU is not set @@ -525,6 +536,7 @@ CONFIG_USB_ETH=y # CONFIG_USB_G_SERIAL is not set # CONFIG_USB_MIDI_GADGET is not set # CONFIG_USB_G_PRINTER is not set +# CONFIG_USB_CDC_COMPOSITE is not set # CONFIG_MMC is not set # CONFIG_MEMSTICK is not set # CONFIG_NEW_LEDS is not set @@ -547,6 +559,8 @@ CONFIG_RTC_INTF_DEV=y # # SPI RTC drivers # +# CONFIG_RTC_DRV_M41T94 is not set +# CONFIG_RTC_DRV_DS1305 is not set # CONFIG_RTC_DRV_MAX6902 is not set # CONFIG_RTC_DRV_R9701 is not set # CONFIG_RTC_DRV_RS5C348 is not set @@ -566,6 +580,7 @@ CONFIG_RTC_INTF_DEV=y # on-CPU RTC drivers # CONFIG_RTC_DRV_AT32AP700X=y +# CONFIG_DMADEVICES is not set # CONFIG_UIO is not set # @@ -620,6 +635,7 @@ CONFIG_MAGIC_SYSRQ=y # CONFIG_HEADERS_CHECK is not set # CONFIG_DEBUG_KERNEL is not set # CONFIG_DEBUG_BUGVERBOSE is not set +# CONFIG_DEBUG_MEMORY_INIT is not set # CONFIG_SAMPLES is not set # @@ -638,12 +654,14 @@ CONFIG_BITREVERSE=y # CONFIG_GENERIC_FIND_NEXT_BIT is not set # CONFIG_CRC_CCITT is not set # CONFIG_CRC16 is not set +# CONFIG_CRC_T10DIF is not set # CONFIG_CRC_ITU_T is not set CONFIG_CRC32=y # CONFIG_CRC7 is not set # CONFIG_LIBCRC32C is not set CONFIG_ZLIB_INFLATE=y CONFIG_ZLIB_DEFLATE=y +CONFIG_GENERIC_ALLOCATOR=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y diff --git a/arch/avr32/configs/atstk1006_defconfig b/arch/avr32/configs/atstk1006_defconfig new file mode 100644 index 0000000..8b6e54c --- /dev/null +++ b/arch/avr32/configs/atstk1006_defconfig @@ -0,0 +1,1304 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.27-rc1 +# Tue Aug 5 15:40:26 2008 +# +CONFIG_AVR32=y +CONFIG_GENERIC_GPIO=y +CONFIG_GENERIC_HARDIRQS=y +CONFIG_STACKTRACE_SUPPORT=y +CONFIG_LOCKDEP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y +CONFIG_HARDIRQS_SW_RESEND=y +CONFIG_GENERIC_IRQ_PROBE=y +CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_CLOCKEVENTS=y +# CONFIG_RWSEM_XCHGADD_ALGORITHM is not set +# CONFIG_ARCH_HAS_ILOG2_U32 is not set +# CONFIG_ARCH_HAS_ILOG2_U64 is not set +CONFIG_GENERIC_HWEIGHT=y +CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_GENERIC_BUG=y +CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" + +# +# General setup +# +CONFIG_EXPERIMENTAL=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_INIT_ENV_ARG_LIMIT=32 +CONFIG_LOCALVERSION="" +# CONFIG_LOCALVERSION_AUTO is not set +CONFIG_SWAP=y +CONFIG_SYSVIPC=y +CONFIG_SYSVIPC_SYSCTL=y +CONFIG_POSIX_MQUEUE=y +# CONFIG_BSD_PROCESS_ACCT is not set +# CONFIG_TASKSTATS is not set +# CONFIG_AUDIT is not set +# CONFIG_IKCONFIG is not set +CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +# CONFIG_GROUP_SCHED is not set +CONFIG_SYSFS_DEPRECATED=y +CONFIG_SYSFS_DEPRECATED_V2=y +CONFIG_RELAY=y +# CONFIG_NAMESPACES is not set +CONFIG_BLK_DEV_INITRD=y +CONFIG_INITRAMFS_SOURCE="" +CONFIG_CC_OPTIMIZE_FOR_SIZE=y +CONFIG_SYSCTL=y +CONFIG_EMBEDDED=y +# CONFIG_SYSCTL_SYSCALL is not set +CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_ALL is not set +# CONFIG_KALLSYMS_EXTRA_PASS is not set +CONFIG_HOTPLUG=y +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_ELF_CORE=y +# CONFIG_COMPAT_BRK is not set +# CONFIG_BASE_FULL is not set +CONFIG_FUTEX=y +CONFIG_ANON_INODES=y +CONFIG_EPOLL=y +CONFIG_SIGNALFD=y +CONFIG_TIMERFD=y +CONFIG_EVENTFD=y +CONFIG_SHMEM=y +CONFIG_VM_EVENT_COUNTERS=y +CONFIG_SLUB_DEBUG=y +# CONFIG_SLAB is not set +CONFIG_SLUB=y +# CONFIG_SLOB is not set +CONFIG_PROFILING=y +# CONFIG_MARKERS is not set +CONFIG_OPROFILE=m +CONFIG_HAVE_OPROFILE=y +CONFIG_KPROBES=y +# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set +# CONFIG_HAVE_IOREMAP_PROT is not set +CONFIG_HAVE_KPROBES=y +# CONFIG_HAVE_KRETPROBES is not set +# CONFIG_HAVE_ARCH_TRACEHOOK is not set +# CONFIG_HAVE_DMA_ATTRS is not set +# CONFIG_USE_GENERIC_SMP_HELPERS is not set +CONFIG_HAVE_CLK=y +CONFIG_PROC_PAGE_MONITOR=y +# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set +CONFIG_SLABINFO=y +CONFIG_RT_MUTEXES=y +# CONFIG_TINY_SHMEM is not set +CONFIG_BASE_SMALL=1 +CONFIG_MODULES=y +# CONFIG_MODULE_FORCE_LOAD is not set +CONFIG_MODULE_UNLOAD=y +# CONFIG_MODULE_FORCE_UNLOAD is not set +# CONFIG_MODVERSIONS is not set +# CONFIG_MODULE_SRCVERSION_ALL is not set +CONFIG_KMOD=y +CONFIG_BLOCK=y +# CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set +# CONFIG_BLK_DEV_BSG is not set +# CONFIG_BLK_DEV_INTEGRITY is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +# CONFIG_IOSCHED_AS is not set +# CONFIG_IOSCHED_DEADLINE is not set +CONFIG_IOSCHED_CFQ=y +# CONFIG_DEFAULT_AS is not set +# CONFIG_DEFAULT_DEADLINE is not set +CONFIG_DEFAULT_CFQ=y +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="cfq" +CONFIG_CLASSIC_RCU=y + +# +# System Type and features +# +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y +CONFIG_SUBARCH_AVR32B=y +CONFIG_MMU=y +CONFIG_PERFORMANCE_COUNTERS=y +CONFIG_PLATFORM_AT32AP=y +CONFIG_CPU_AT32AP700X=y +CONFIG_CPU_AT32AP7000=y +CONFIG_BOARD_ATSTK1000=y +# CONFIG_BOARD_ATNGW100 is not set +# CONFIG_BOARD_ATSTK1002 is not set +# CONFIG_BOARD_ATSTK1003 is not set +# CONFIG_BOARD_ATSTK1004 is not set +CONFIG_BOARD_ATSTK1006=y +# CONFIG_BOARD_ATSTK100X_CUSTOM is not set +# CONFIG_BOARD_ATSTK100X_SPI1 is not set +# CONFIG_BOARD_ATSTK1000_J2_LED is not set +# CONFIG_BOARD_ATSTK1000_J2_LED8 is not set +# CONFIG_BOARD_ATSTK1000_J2_RGB is not set +CONFIG_BOARD_ATSTK1000_EXTDAC=y +CONFIG_LOADER_U_BOOT=y + +# +# Atmel AVR32 AP options +# +# CONFIG_AP700X_32_BIT_SMC is not set +CONFIG_AP700X_16_BIT_SMC=y +# CONFIG_AP700X_8_BIT_SMC is not set +CONFIG_LOAD_ADDRESS=0x10000000 +CONFIG_ENTRY_ADDRESS=0x90000000 +CONFIG_PHYS_OFFSET=0x10000000 +CONFIG_PREEMPT_NONE=y +# CONFIG_PREEMPT_VOLUNTARY is not set +# CONFIG_PREEMPT is not set +CONFIG_QUICKLIST=y +# CONFIG_HAVE_ARCH_BOOTMEM_NODE is not set +# CONFIG_ARCH_HAVE_MEMORY_PRESENT is not set +# CONFIG_NEED_NODE_MEMMAP_SIZE is not set +CONFIG_ARCH_FLATMEM_ENABLE=y +# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set +# CONFIG_ARCH_SPARSEMEM_ENABLE is not set +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +# CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set +CONFIG_PAGEFLAGS_EXTENDED=y +CONFIG_SPLIT_PTLOCK_CPUS=4 +# CONFIG_RESOURCES_64BIT is not set +CONFIG_ZONE_DMA_FLAG=0 +CONFIG_NR_QUICK=2 +CONFIG_VIRT_TO_BUS=y +# CONFIG_OWNERSHIP_TRACE is not set +CONFIG_NMI_DEBUGGING=y +# CONFIG_HZ_100 is not set +CONFIG_HZ_250=y +# CONFIG_HZ_300 is not set +# CONFIG_HZ_1000 is not set +CONFIG_HZ=250 +# CONFIG_SCHED_HRTICK is not set +CONFIG_CMDLINE="" + +# +# Power management options +# +CONFIG_PM=y +# CONFIG_PM_DEBUG is not set +CONFIG_PM_SLEEP=y +CONFIG_SUSPEND=y +CONFIG_SUSPEND_FREEZER=y +CONFIG_ARCH_SUSPEND_POSSIBLE=y + +# +# CPU Frequency scaling +# +CONFIG_CPU_FREQ=y +CONFIG_CPU_FREQ_TABLE=y +# CONFIG_CPU_FREQ_DEBUG is not set +# CONFIG_CPU_FREQ_STAT is not set +# CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE is not set +# CONFIG_CPU_FREQ_DEFAULT_GOV_POWERSAVE is not set +# CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set +CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND=y +# CONFIG_CPU_FREQ_DEFAULT_GOV_CONSERVATIVE is not set +CONFIG_CPU_FREQ_GOV_PERFORMANCE=y +# CONFIG_CPU_FREQ_GOV_POWERSAVE is not set +CONFIG_CPU_FREQ_GOV_USERSPACE=y +CONFIG_CPU_FREQ_GOV_ONDEMAND=y +# CONFIG_CPU_FREQ_GOV_CONSERVATIVE is not set +CONFIG_CPU_FREQ_AT32AP=y + +# +# Bus options +# +# CONFIG_ARCH_SUPPORTS_MSI is not set +# CONFIG_PCCARD is not set + +# +# Executable file formats +# +CONFIG_BINFMT_ELF=y +# CONFIG_BINFMT_MISC is not set +CONFIG_NET=y + +# +# Networking options +# +CONFIG_PACKET=y +CONFIG_PACKET_MMAP=y +CONFIG_UNIX=y +CONFIG_XFRM=y +CONFIG_XFRM_USER=m +# CONFIG_XFRM_SUB_POLICY is not set +# CONFIG_XFRM_MIGRATE is not set +# CONFIG_XFRM_STATISTICS is not set +CONFIG_XFRM_IPCOMP=m +CONFIG_NET_KEY=m +# CONFIG_NET_KEY_MIGRATE is not set +CONFIG_INET=y +# CONFIG_IP_MULTICAST is not set +# CONFIG_IP_ADVANCED_ROUTER is not set +CONFIG_IP_FIB_HASH=y +CONFIG_IP_PNP=y +CONFIG_IP_PNP_DHCP=y +# CONFIG_IP_PNP_BOOTP is not set +# CONFIG_IP_PNP_RARP is not set +CONFIG_NET_IPIP=m +CONFIG_NET_IPGRE=m +# CONFIG_ARPD is not set +# CONFIG_SYN_COOKIES is not set +CONFIG_INET_AH=m +CONFIG_INET_ESP=m +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set +CONFIG_INET_TUNNEL=m +CONFIG_INET_XFRM_MODE_TRANSPORT=m +CONFIG_INET_XFRM_MODE_TUNNEL=m +CONFIG_INET_XFRM_MODE_BEET=m +# CONFIG_INET_LRO is not set +CONFIG_INET_DIAG=y +CONFIG_INET_TCP_DIAG=y +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_CUBIC=y +CONFIG_DEFAULT_TCP_CONG="cubic" +# CONFIG_TCP_MD5SIG is not set +CONFIG_IPV6=m +# CONFIG_IPV6_PRIVACY is not set +# CONFIG_IPV6_ROUTER_PREF is not set +# CONFIG_IPV6_OPTIMISTIC_DAD is not set +CONFIG_INET6_AH=m +CONFIG_INET6_ESP=m +CONFIG_INET6_IPCOMP=m +# CONFIG_IPV6_MIP6 is not set +CONFIG_INET6_XFRM_TUNNEL=m +CONFIG_INET6_TUNNEL=m +CONFIG_INET6_XFRM_MODE_TRANSPORT=m +CONFIG_INET6_XFRM_MODE_TUNNEL=m +CONFIG_INET6_XFRM_MODE_BEET=m +# CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION is not set +CONFIG_IPV6_SIT=m +CONFIG_IPV6_NDISC_NODETYPE=y +CONFIG_IPV6_TUNNEL=m +# CONFIG_IPV6_MULTIPLE_TABLES is not set +# CONFIG_IPV6_MROUTE is not set +# CONFIG_NETWORK_SECMARK is not set +# CONFIG_NETFILTER is not set +# CONFIG_IP_DCCP is not set +# CONFIG_IP_SCTP is not set +# CONFIG_TIPC is not set +# CONFIG_ATM is not set +CONFIG_STP=m +CONFIG_BRIDGE=m +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +CONFIG_LLC=m +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set +# CONFIG_ECONET is not set +# CONFIG_WAN_ROUTER is not set +# CONFIG_NET_SCHED is not set + +# +# Network testing +# +# CONFIG_NET_PKTGEN is not set +# CONFIG_NET_TCPPROBE is not set +# CONFIG_HAMRADIO is not set +# CONFIG_CAN is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set +# CONFIG_AF_RXRPC is not set + +# +# Wireless +# +# CONFIG_CFG80211 is not set +# CONFIG_WIRELESS_EXT is not set +# CONFIG_MAC80211 is not set +# CONFIG_IEEE80211 is not set +# CONFIG_RFKILL is not set +# CONFIG_NET_9P is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" +CONFIG_STANDALONE=y +# CONFIG_PREVENT_FIRMWARE_BUILD is not set +# CONFIG_FW_LOADER is not set +# CONFIG_DEBUG_DRIVER is not set +# CONFIG_DEBUG_DEVRES is not set +# CONFIG_SYS_HYPERVISOR is not set +# CONFIG_CONNECTOR is not set +CONFIG_MTD=y +# CONFIG_MTD_DEBUG is not set +# CONFIG_MTD_CONCAT is not set +CONFIG_MTD_PARTITIONS=y +# CONFIG_MTD_REDBOOT_PARTS is not set +CONFIG_MTD_CMDLINE_PARTS=y +# CONFIG_MTD_AR7_PARTS is not set + +# +# User Modules And Translation Layers +# +CONFIG_MTD_CHAR=y +CONFIG_MTD_BLKDEVS=y +CONFIG_MTD_BLOCK=y +# CONFIG_FTL is not set +# CONFIG_NFTL is not set +# CONFIG_INFTL is not set +# CONFIG_RFD_FTL is not set +# CONFIG_SSFDC is not set +# CONFIG_MTD_OOPS is not set + +# +# RAM/ROM/Flash chip drivers +# +CONFIG_MTD_CFI=y +# CONFIG_MTD_JEDECPROBE is not set +CONFIG_MTD_GEN_PROBE=y +# CONFIG_MTD_CFI_ADV_OPTIONS is not set +CONFIG_MTD_MAP_BANK_WIDTH_1=y +CONFIG_MTD_MAP_BANK_WIDTH_2=y +CONFIG_MTD_MAP_BANK_WIDTH_4=y +# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set +CONFIG_MTD_CFI_I1=y +CONFIG_MTD_CFI_I2=y +# CONFIG_MTD_CFI_I4 is not set +# CONFIG_MTD_CFI_I8 is not set +# CONFIG_MTD_CFI_INTELEXT is not set +CONFIG_MTD_CFI_AMDSTD=y +# CONFIG_MTD_CFI_STAA is not set +CONFIG_MTD_CFI_UTIL=y +# CONFIG_MTD_RAM is not set +# CONFIG_MTD_ROM is not set +# CONFIG_MTD_ABSENT is not set + +# +# Mapping drivers for chip access +# +# CONFIG_MTD_COMPLEX_MAPPINGS is not set +CONFIG_MTD_PHYSMAP=y +CONFIG_MTD_PHYSMAP_START=0x8000000 +CONFIG_MTD_PHYSMAP_LEN=0x0 +CONFIG_MTD_PHYSMAP_BANKWIDTH=2 +# CONFIG_MTD_PLATRAM is not set + +# +# Self-contained MTD device drivers +# +CONFIG_MTD_DATAFLASH=m +CONFIG_MTD_M25P80=m +CONFIG_M25PXX_USE_FAST_READ=y +# CONFIG_MTD_SLRAM is not set +# CONFIG_MTD_PHRAM is not set +# CONFIG_MTD_MTDRAM is not set +# CONFIG_MTD_BLOCK2MTD is not set + +# +# Disk-On-Chip Device Drivers +# +# CONFIG_MTD_DOC2000 is not set +# CONFIG_MTD_DOC2001 is not set +# CONFIG_MTD_DOC2001PLUS is not set +CONFIG_MTD_NAND=y +# CONFIG_MTD_NAND_VERIFY_WRITE is not set +# CONFIG_MTD_NAND_ECC_SMC is not set +# CONFIG_MTD_NAND_MUSEUM_IDS is not set +CONFIG_MTD_NAND_IDS=y +# CONFIG_MTD_NAND_DISKONCHIP is not set +CONFIG_MTD_NAND_ATMEL=y +CONFIG_MTD_NAND_ATMEL_ECC_HW=y +# CONFIG_MTD_NAND_ATMEL_ECC_SOFT is not set +# CONFIG_MTD_NAND_ATMEL_ECC_NONE is not set +# CONFIG_MTD_NAND_NANDSIM is not set +# CONFIG_MTD_NAND_PLATFORM is not set +# CONFIG_MTD_ONENAND is not set + +# +# UBI - Unsorted block images +# +CONFIG_MTD_UBI=y +CONFIG_MTD_UBI_WL_THRESHOLD=4096 +CONFIG_MTD_UBI_BEB_RESERVE=1 +# CONFIG_MTD_UBI_GLUEBI is not set + +# +# UBI debugging options +# +# CONFIG_MTD_UBI_DEBUG is not set +# CONFIG_PARPORT is not set +CONFIG_BLK_DEV=y +# CONFIG_BLK_DEV_COW_COMMON is not set +CONFIG_BLK_DEV_LOOP=m +# CONFIG_BLK_DEV_CRYPTOLOOP is not set +CONFIG_BLK_DEV_NBD=m +CONFIG_BLK_DEV_RAM=m +CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=4096 +# CONFIG_BLK_DEV_XIP is not set +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set +CONFIG_MISC_DEVICES=y +CONFIG_ATMEL_PWM=m +CONFIG_ATMEL_TCLIB=y +CONFIG_ATMEL_TCB_CLKSRC=y +CONFIG_ATMEL_TCB_CLKSRC_BLOCK=0 +# CONFIG_EEPROM_93CX6 is not set +CONFIG_ATMEL_SSC=m +# CONFIG_ENCLOSURE_SERVICES is not set +# CONFIG_HAVE_IDE is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +CONFIG_SCSI=m +CONFIG_SCSI_DMA=y +# CONFIG_SCSI_TGT is not set +# CONFIG_SCSI_NETLINK is not set +# CONFIG_SCSI_PROC_FS is not set + +# +# SCSI support type (disk, tape, CD-ROM) +# +CONFIG_BLK_DEV_SD=m +# CONFIG_CHR_DEV_ST is not set +# CONFIG_CHR_DEV_OSST is not set +CONFIG_BLK_DEV_SR=m +# CONFIG_BLK_DEV_SR_VENDOR is not set +# CONFIG_CHR_DEV_SG is not set +# CONFIG_CHR_DEV_SCH is not set + +# +# Some SCSI devices (e.g. CD jukebox) support multiple LUNs +# +# CONFIG_SCSI_MULTI_LUN is not set +# CONFIG_SCSI_CONSTANTS is not set +# CONFIG_SCSI_LOGGING is not set +# CONFIG_SCSI_SCAN_ASYNC is not set +CONFIG_SCSI_WAIT_SCAN=m + +# +# SCSI Transports +# +# CONFIG_SCSI_SPI_ATTRS is not set +# CONFIG_SCSI_FC_ATTRS is not set +# CONFIG_SCSI_ISCSI_ATTRS is not set +# CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set +# CONFIG_SCSI_LOWLEVEL is not set +# CONFIG_SCSI_DH is not set +CONFIG_ATA=m +# CONFIG_ATA_NONSTANDARD is not set +# CONFIG_SATA_PMP is not set +CONFIG_ATA_SFF=y +# CONFIG_SATA_MV is not set +CONFIG_PATA_AT32=m +# CONFIG_PATA_PLATFORM is not set +# CONFIG_MD is not set +CONFIG_NETDEVICES=y +# CONFIG_DUMMY is not set +# CONFIG_BONDING is not set +# CONFIG_MACVLAN is not set +# CONFIG_EQUALIZER is not set +CONFIG_TUN=m +# CONFIG_VETH is not set +CONFIG_PHYLIB=y + +# +# MII PHY device drivers +# +# CONFIG_MARVELL_PHY is not set +# CONFIG_DAVICOM_PHY is not set +# CONFIG_QSEMI_PHY is not set +# CONFIG_LXT_PHY is not set +# CONFIG_CICADA_PHY is not set +# CONFIG_VITESSE_PHY is not set +# CONFIG_SMSC_PHY is not set +# CONFIG_BROADCOM_PHY is not set +# CONFIG_ICPLUS_PHY is not set +# CONFIG_REALTEK_PHY is not set +# CONFIG_FIXED_PHY is not set +# CONFIG_MDIO_BITBANG is not set +CONFIG_NET_ETHERNET=y +# CONFIG_MII is not set +CONFIG_MACB=y +# CONFIG_ENC28J60 is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_B44 is not set +# CONFIG_NETDEV_1000 is not set +# CONFIG_NETDEV_10000 is not set + +# +# Wireless LAN +# +# CONFIG_WLAN_PRE80211 is not set +# CONFIG_WLAN_80211 is not set +# CONFIG_IWLWIFI_LEDS is not set +# CONFIG_WAN is not set +CONFIG_PPP=m +# CONFIG_PPP_MULTILINK is not set +# CONFIG_PPP_FILTER is not set +CONFIG_PPP_ASYNC=m +# CONFIG_PPP_SYNC_TTY is not set +CONFIG_PPP_DEFLATE=m +CONFIG_PPP_BSDCOMP=m +# CONFIG_PPP_MPPE is not set +# CONFIG_PPPOE is not set +# CONFIG_PPPOL2TP is not set +# CONFIG_SLIP is not set +CONFIG_SLHC=m +# CONFIG_NETCONSOLE is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set +# CONFIG_ISDN is not set +# CONFIG_PHONE is not set + +# +# Input device support +# +CONFIG_INPUT=m +# CONFIG_INPUT_FF_MEMLESS is not set +CONFIG_INPUT_POLLDEV=m + +# +# Userland interfaces +# +CONFIG_INPUT_MOUSEDEV=m +CONFIG_INPUT_MOUSEDEV_PSAUX=y +CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 +CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 +# CONFIG_INPUT_JOYDEV is not set +CONFIG_INPUT_EVDEV=m +# CONFIG_INPUT_EVBUG is not set + +# +# Input Device Drivers +# +CONFIG_INPUT_KEYBOARD=y +# CONFIG_KEYBOARD_ATKBD is not set +# CONFIG_KEYBOARD_SUNKBD is not set +# CONFIG_KEYBOARD_LKKBD is not set +# CONFIG_KEYBOARD_XTKBD is not set +# CONFIG_KEYBOARD_NEWTON is not set +# CONFIG_KEYBOARD_STOWAWAY is not set +CONFIG_KEYBOARD_GPIO=m +CONFIG_INPUT_MOUSE=y +# CONFIG_MOUSE_PS2 is not set +# CONFIG_MOUSE_SERIAL is not set +# CONFIG_MOUSE_VSXXXAA is not set +CONFIG_MOUSE_GPIO=m +# CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TABLET is not set +# CONFIG_INPUT_TOUCHSCREEN is not set +# CONFIG_INPUT_MISC is not set + +# +# Hardware I/O ports +# +# CONFIG_SERIO is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +# CONFIG_VT is not set +# CONFIG_DEVKMEM is not set +# CONFIG_SERIAL_NONSTANDARD is not set + +# +# Serial drivers +# +# CONFIG_SERIAL_8250 is not set + +# +# Non-8250 serial port support +# +CONFIG_SERIAL_ATMEL=y +CONFIG_SERIAL_ATMEL_CONSOLE=y +CONFIG_SERIAL_ATMEL_PDC=y +# CONFIG_SERIAL_ATMEL_TTYAT is not set +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +CONFIG_UNIX98_PTYS=y +# CONFIG_LEGACY_PTYS is not set +# CONFIG_IPMI_HANDLER is not set +# CONFIG_HW_RANDOM is not set +# CONFIG_R3964 is not set +# CONFIG_RAW_DRIVER is not set +# CONFIG_TCG_TPM is not set +CONFIG_I2C=m +CONFIG_I2C_BOARDINFO=y +CONFIG_I2C_CHARDEV=m +CONFIG_I2C_ALGOBIT=m + +# +# I2C Hardware Bus support +# + +# +# I2C system bus drivers (mostly embedded / system-on-chip) +# +CONFIG_I2C_GPIO=m +# CONFIG_I2C_OCORES is not set +# CONFIG_I2C_SIMTEC is not set + +# +# External I2C/SMBus adapter drivers +# +# CONFIG_I2C_PARPORT_LIGHT is not set +# CONFIG_I2C_TAOS_EVM is not set + +# +# Other I2C/SMBus bus drivers +# +# CONFIG_I2C_PCA_PLATFORM is not set +# CONFIG_I2C_STUB is not set + +# +# Miscellaneous I2C Chip support +# +# CONFIG_DS1682 is not set +# CONFIG_AT24 is not set +# CONFIG_SENSORS_EEPROM is not set +# CONFIG_SENSORS_PCF8574 is not set +# CONFIG_PCF8575 is not set +# CONFIG_SENSORS_PCA9539 is not set +# CONFIG_SENSORS_PCF8591 is not set +# CONFIG_TPS65010 is not set +# CONFIG_SENSORS_MAX6875 is not set +# CONFIG_SENSORS_TSL2550 is not set +# CONFIG_I2C_DEBUG_CORE is not set +# CONFIG_I2C_DEBUG_ALGO is not set +# CONFIG_I2C_DEBUG_BUS is not set +# CONFIG_I2C_DEBUG_CHIP is not set +CONFIG_SPI=y +# CONFIG_SPI_DEBUG is not set +CONFIG_SPI_MASTER=y + +# +# SPI Master Controller Drivers +# +CONFIG_SPI_ATMEL=y +# CONFIG_SPI_BITBANG is not set + +# +# SPI Protocol Masters +# +# CONFIG_SPI_AT25 is not set +CONFIG_SPI_SPIDEV=m +# CONFIG_SPI_TLE62X0 is not set +CONFIG_ARCH_REQUIRE_GPIOLIB=y +CONFIG_GPIOLIB=y +# CONFIG_DEBUG_GPIO is not set +CONFIG_GPIO_SYSFS=y + +# +# I2C GPIO expanders: +# +# CONFIG_GPIO_MAX732X is not set +# CONFIG_GPIO_PCA953X is not set +# CONFIG_GPIO_PCF857X is not set + +# +# PCI GPIO expanders: +# + +# +# SPI GPIO expanders: +# +# CONFIG_GPIO_MAX7301 is not set +# CONFIG_GPIO_MCP23S08 is not set +# CONFIG_W1 is not set +# CONFIG_POWER_SUPPLY is not set +# CONFIG_HWMON is not set +# CONFIG_THERMAL is not set +# CONFIG_THERMAL_HWMON is not set +CONFIG_WATCHDOG=y +# CONFIG_WATCHDOG_NOWAYOUT is not set + +# +# Watchdog Device Drivers +# +# CONFIG_SOFT_WATCHDOG is not set +CONFIG_AT32AP700X_WDT=y + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set + +# +# Multifunction device drivers +# +# CONFIG_MFD_CORE is not set +# CONFIG_MFD_SM501 is not set +# CONFIG_HTC_PASIC3 is not set + +# +# Multimedia devices +# + +# +# Multimedia core support +# +# CONFIG_VIDEO_DEV is not set +# CONFIG_DVB_CORE is not set +# CONFIG_VIDEO_MEDIA is not set + +# +# Multimedia drivers +# +# CONFIG_DAB is not set + +# +# Graphics support +# +# CONFIG_VGASTATE is not set +# CONFIG_VIDEO_OUTPUT_CONTROL is not set +CONFIG_FB=y +# CONFIG_FIRMWARE_EDID is not set +# CONFIG_FB_DDC is not set +CONFIG_FB_CFB_FILLRECT=y +CONFIG_FB_CFB_COPYAREA=y +CONFIG_FB_CFB_IMAGEBLIT=y +# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set +# CONFIG_FB_SYS_FILLRECT is not set +# CONFIG_FB_SYS_COPYAREA is not set +# CONFIG_FB_SYS_IMAGEBLIT is not set +# CONFIG_FB_FOREIGN_ENDIAN is not set +# CONFIG_FB_SYS_FOPS is not set +# CONFIG_FB_SVGALIB is not set +# CONFIG_FB_MACMODES is not set +# CONFIG_FB_BACKLIGHT is not set +# CONFIG_FB_MODE_HELPERS is not set +# CONFIG_FB_TILEBLITTING is not set + +# +# Frame buffer hardware drivers +# +# CONFIG_FB_S1D13XXX is not set +CONFIG_FB_ATMEL=y +# CONFIG_FB_VIRTUAL is not set +CONFIG_BACKLIGHT_LCD_SUPPORT=y +CONFIG_LCD_CLASS_DEVICE=y +CONFIG_LCD_LTV350QV=y +# CONFIG_LCD_ILI9320 is not set +# CONFIG_LCD_VGG2432A4 is not set +# CONFIG_LCD_PLATFORM is not set +# CONFIG_BACKLIGHT_CLASS_DEVICE is not set + +# +# Display device support +# +# CONFIG_DISPLAY_SUPPORT is not set +# CONFIG_LOGO is not set +CONFIG_SOUND=m +CONFIG_SND=m +CONFIG_SND_TIMER=m +CONFIG_SND_PCM=m +# CONFIG_SND_SEQUENCER is not set +CONFIG_SND_OSSEMUL=y +CONFIG_SND_MIXER_OSS=m +CONFIG_SND_PCM_OSS=m +CONFIG_SND_PCM_OSS_PLUGINS=y +# CONFIG_SND_DYNAMIC_MINORS is not set +# CONFIG_SND_SUPPORT_OLD_API is not set +# CONFIG_SND_VERBOSE_PROCFS is not set +# CONFIG_SND_VERBOSE_PRINTK is not set +# CONFIG_SND_DEBUG is not set +CONFIG_SND_DRIVERS=y +# CONFIG_SND_DUMMY is not set +# CONFIG_SND_MTPAV is not set +# CONFIG_SND_SERIAL_U16550 is not set +# CONFIG_SND_MPU401 is not set +CONFIG_SND_SPI=y +CONFIG_SND_AT73C213=m +CONFIG_SND_AT73C213_TARGET_BITRATE=48000 +# CONFIG_SND_SOC is not set +# CONFIG_SOUND_PRIME is not set +# CONFIG_HID_SUPPORT is not set +CONFIG_USB_SUPPORT=y +# CONFIG_USB_ARCH_HAS_HCD is not set +# CONFIG_USB_ARCH_HAS_OHCI is not set +# CONFIG_USB_ARCH_HAS_EHCI is not set +# CONFIG_USB_OTG_WHITELIST is not set +# CONFIG_USB_OTG_BLACKLIST_HUB is not set + +# +# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' +# +CONFIG_USB_GADGET=y +# CONFIG_USB_GADGET_DEBUG is not set +# CONFIG_USB_GADGET_DEBUG_FILES is not set +# CONFIG_USB_GADGET_DEBUG_FS is not set +CONFIG_USB_GADGET_SELECTED=y +# CONFIG_USB_GADGET_AMD5536UDC is not set +CONFIG_USB_GADGET_ATMEL_USBA=y +CONFIG_USB_ATMEL_USBA=y +# CONFIG_USB_GADGET_FSL_USB2 is not set +# CONFIG_USB_GADGET_NET2280 is not set +# CONFIG_USB_GADGET_PXA25X is not set +# CONFIG_USB_GADGET_M66592 is not set +# CONFIG_USB_GADGET_PXA27X is not set +# CONFIG_USB_GADGET_GOKU is not set +# CONFIG_USB_GADGET_LH7A40X is not set +# CONFIG_USB_GADGET_OMAP is not set +# CONFIG_USB_GADGET_S3C2410 is not set +# CONFIG_USB_GADGET_AT91 is not set +# CONFIG_USB_GADGET_DUMMY_HCD is not set +CONFIG_USB_GADGET_DUALSPEED=y +CONFIG_USB_ZERO=m +CONFIG_USB_ETH=m +CONFIG_USB_ETH_RNDIS=y +CONFIG_USB_GADGETFS=m +CONFIG_USB_FILE_STORAGE=m +# CONFIG_USB_FILE_STORAGE_TEST is not set +CONFIG_USB_G_SERIAL=m +# CONFIG_USB_MIDI_GADGET is not set +# CONFIG_USB_G_PRINTER is not set +# CONFIG_USB_CDC_COMPOSITE is not set +CONFIG_MMC=y +# CONFIG_MMC_DEBUG is not set +# CONFIG_MMC_UNSAFE_RESUME is not set + +# +# MMC/SD Card Drivers +# +CONFIG_MMC_BLOCK=y +CONFIG_MMC_BLOCK_BOUNCE=y +# CONFIG_SDIO_UART is not set +# CONFIG_MMC_TEST is not set + +# +# MMC/SD Host Controller Drivers +# +# CONFIG_MMC_SDHCI is not set +CONFIG_MMC_ATMELMCI=y +CONFIG_MMC_SPI=m +# CONFIG_MEMSTICK is not set +CONFIG_NEW_LEDS=y +CONFIG_LEDS_CLASS=m + +# +# LED drivers +# +CONFIG_LEDS_ATMEL_PWM=m +# CONFIG_LEDS_PCA9532 is not set +CONFIG_LEDS_GPIO=m +# CONFIG_LEDS_PCA955X is not set + +# +# LED Triggers +# +CONFIG_LEDS_TRIGGERS=y +CONFIG_LEDS_TRIGGER_TIMER=m +CONFIG_LEDS_TRIGGER_HEARTBEAT=m +CONFIG_LEDS_TRIGGER_DEFAULT_ON=m +# CONFIG_ACCESSIBILITY is not set +CONFIG_RTC_LIB=y +CONFIG_RTC_CLASS=y +CONFIG_RTC_HCTOSYS=y +CONFIG_RTC_HCTOSYS_DEVICE="rtc0" +# CONFIG_RTC_DEBUG is not set + +# +# RTC interfaces +# +CONFIG_RTC_INTF_SYSFS=y +CONFIG_RTC_INTF_PROC=y +CONFIG_RTC_INTF_DEV=y +# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set +# CONFIG_RTC_DRV_TEST is not set + +# +# I2C RTC drivers +# +# CONFIG_RTC_DRV_DS1307 is not set +# CONFIG_RTC_DRV_DS1374 is not set +# CONFIG_RTC_DRV_DS1672 is not set +# CONFIG_RTC_DRV_MAX6900 is not set +# CONFIG_RTC_DRV_RS5C372 is not set +# CONFIG_RTC_DRV_ISL1208 is not set +# CONFIG_RTC_DRV_X1205 is not set +# CONFIG_RTC_DRV_PCF8563 is not set +# CONFIG_RTC_DRV_PCF8583 is not set +# CONFIG_RTC_DRV_M41T80 is not set +# CONFIG_RTC_DRV_S35390A is not set +# CONFIG_RTC_DRV_FM3130 is not set + +# +# SPI RTC drivers +# +# CONFIG_RTC_DRV_M41T94 is not set +# CONFIG_RTC_DRV_DS1305 is not set +# CONFIG_RTC_DRV_MAX6902 is not set +# CONFIG_RTC_DRV_R9701 is not set +# CONFIG_RTC_DRV_RS5C348 is not set + +# +# Platform RTC drivers +# +# CONFIG_RTC_DRV_DS1511 is not set +# CONFIG_RTC_DRV_DS1553 is not set +# CONFIG_RTC_DRV_DS1742 is not set +# CONFIG_RTC_DRV_STK17TA8 is not set +# CONFIG_RTC_DRV_M48T86 is not set +# CONFIG_RTC_DRV_M48T59 is not set +# CONFIG_RTC_DRV_V3020 is not set + +# +# on-CPU RTC drivers +# +CONFIG_RTC_DRV_AT32AP700X=y +CONFIG_DMADEVICES=y + +# +# DMA Devices +# +CONFIG_DW_DMAC=y +CONFIG_DMA_ENGINE=y + +# +# DMA Clients +# +# CONFIG_NET_DMA is not set +CONFIG_DMATEST=m +# CONFIG_UIO is not set + +# +# File systems +# +CONFIG_EXT2_FS=m +# CONFIG_EXT2_FS_XATTR is not set +# CONFIG_EXT2_FS_XIP is not set +CONFIG_EXT3_FS=m +# CONFIG_EXT3_FS_XATTR is not set +# CONFIG_EXT4DEV_FS is not set +CONFIG_JBD=m +# CONFIG_JBD_DEBUG is not set +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +# CONFIG_FS_POSIX_ACL is not set +# CONFIG_XFS_FS is not set +# CONFIG_OCFS2_FS is not set +# CONFIG_DNOTIFY is not set +CONFIG_INOTIFY=y +CONFIG_INOTIFY_USER=y +# CONFIG_QUOTA is not set +# CONFIG_AUTOFS_FS is not set +# CONFIG_AUTOFS4_FS is not set +CONFIG_FUSE_FS=m + +# +# CD-ROM/DVD Filesystems +# +# CONFIG_ISO9660_FS is not set +# CONFIG_UDF_FS is not set + +# +# DOS/FAT/NT Filesystems +# +CONFIG_FAT_FS=m +CONFIG_MSDOS_FS=m +CONFIG_VFAT_FS=m +CONFIG_FAT_DEFAULT_CODEPAGE=437 +CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_PROC_KCORE=y +CONFIG_PROC_SYSCTL=y +CONFIG_SYSFS=y +CONFIG_TMPFS=y +# CONFIG_TMPFS_POSIX_ACL is not set +# CONFIG_HUGETLB_PAGE is not set +# CONFIG_CONFIGFS_FS is not set + +# +# Miscellaneous filesystems +# +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +CONFIG_JFFS2_FS=y +CONFIG_JFFS2_FS_DEBUG=0 +# CONFIG_JFFS2_FS_WRITEBUFFER is not set +# CONFIG_JFFS2_SUMMARY is not set +# CONFIG_JFFS2_FS_XATTR is not set +# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set +CONFIG_JFFS2_ZLIB=y +# CONFIG_JFFS2_LZO is not set +CONFIG_JFFS2_RTIME=y +# CONFIG_JFFS2_RUBIN is not set +CONFIG_UBIFS_FS=y +CONFIG_UBIFS_FS_XATTR=y +# CONFIG_UBIFS_FS_ADVANCED_COMPR is not set +CONFIG_UBIFS_FS_LZO=y +CONFIG_UBIFS_FS_ZLIB=y +# CONFIG_UBIFS_FS_DEBUG is not set +# CONFIG_CRAMFS is not set +# CONFIG_VXFS_FS is not set +CONFIG_MINIX_FS=m +# CONFIG_OMFS_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +# CONFIG_ROMFS_FS is not set +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set +CONFIG_NETWORK_FILESYSTEMS=y +CONFIG_NFS_FS=y +CONFIG_NFS_V3=y +# CONFIG_NFS_V3_ACL is not set +# CONFIG_NFS_V4 is not set +CONFIG_ROOT_NFS=y +# CONFIG_NFSD is not set +CONFIG_LOCKD=y +CONFIG_LOCKD_V4=y +CONFIG_NFS_COMMON=y +CONFIG_SUNRPC=y +# CONFIG_RPCSEC_GSS_KRB5 is not set +# CONFIG_RPCSEC_GSS_SPKM3 is not set +# CONFIG_SMB_FS is not set +# CONFIG_CIFS is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set +# CONFIG_AFS_FS is not set + +# +# Partition Types +# +# CONFIG_PARTITION_ADVANCED is not set +CONFIG_MSDOS_PARTITION=y +CONFIG_NLS=m +CONFIG_NLS_DEFAULT="iso8859-1" +CONFIG_NLS_CODEPAGE_437=m +# CONFIG_NLS_CODEPAGE_737 is not set +# CONFIG_NLS_CODEPAGE_775 is not set +# CONFIG_NLS_CODEPAGE_850 is not set +# CONFIG_NLS_CODEPAGE_852 is not set +# CONFIG_NLS_CODEPAGE_855 is not set +# CONFIG_NLS_CODEPAGE_857 is not set +# CONFIG_NLS_CODEPAGE_860 is not set +# CONFIG_NLS_CODEPAGE_861 is not set +# CONFIG_NLS_CODEPAGE_862 is not set +# CONFIG_NLS_CODEPAGE_863 is not set +# CONFIG_NLS_CODEPAGE_864 is not set +# CONFIG_NLS_CODEPAGE_865 is not set +# CONFIG_NLS_CODEPAGE_866 is not set +# CONFIG_NLS_CODEPAGE_869 is not set +# CONFIG_NLS_CODEPAGE_936 is not set +# CONFIG_NLS_CODEPAGE_950 is not set +# CONFIG_NLS_CODEPAGE_932 is not set +# CONFIG_NLS_CODEPAGE_949 is not set +# CONFIG_NLS_CODEPAGE_874 is not set +# CONFIG_NLS_ISO8859_8 is not set +# CONFIG_NLS_CODEPAGE_1250 is not set +# CONFIG_NLS_CODEPAGE_1251 is not set +# CONFIG_NLS_ASCII is not set +CONFIG_NLS_ISO8859_1=m +# CONFIG_NLS_ISO8859_2 is not set +# CONFIG_NLS_ISO8859_3 is not set +# CONFIG_NLS_ISO8859_4 is not set +# CONFIG_NLS_ISO8859_5 is not set +# CONFIG_NLS_ISO8859_6 is not set +# CONFIG_NLS_ISO8859_7 is not set +# CONFIG_NLS_ISO8859_9 is not set +# CONFIG_NLS_ISO8859_13 is not set +# CONFIG_NLS_ISO8859_14 is not set +# CONFIG_NLS_ISO8859_15 is not set +# CONFIG_NLS_KOI8_R is not set +# CONFIG_NLS_KOI8_U is not set +CONFIG_NLS_UTF8=m +# CONFIG_DLM is not set + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y +CONFIG_ENABLE_MUST_CHECK=y +CONFIG_FRAME_WARN=1024 +CONFIG_MAGIC_SYSRQ=y +# CONFIG_UNUSED_SYMBOLS is not set +CONFIG_DEBUG_FS=y +# CONFIG_HEADERS_CHECK is not set +CONFIG_DEBUG_KERNEL=y +# CONFIG_DEBUG_SHIRQ is not set +CONFIG_DETECT_SOFTLOCKUP=y +# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set +CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0 +CONFIG_SCHED_DEBUG=y +# CONFIG_SCHEDSTATS is not set +# CONFIG_TIMER_STATS is not set +# CONFIG_DEBUG_OBJECTS is not set +# CONFIG_SLUB_DEBUG_ON is not set +# CONFIG_SLUB_STATS is not set +# CONFIG_DEBUG_RT_MUTEXES is not set +# CONFIG_RT_MUTEX_TESTER is not set +# CONFIG_DEBUG_SPINLOCK is not set +# CONFIG_DEBUG_MUTEXES is not set +# CONFIG_DEBUG_LOCK_ALLOC is not set +# CONFIG_PROVE_LOCKING is not set +# CONFIG_LOCK_STAT is not set +# CONFIG_DEBUG_SPINLOCK_SLEEP is not set +# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set +# CONFIG_DEBUG_KOBJECT is not set +CONFIG_DEBUG_BUGVERBOSE=y +# CONFIG_DEBUG_INFO is not set +# CONFIG_DEBUG_VM is not set +# CONFIG_DEBUG_WRITECOUNT is not set +# CONFIG_DEBUG_MEMORY_INIT is not set +# CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set +CONFIG_FRAME_POINTER=y +# CONFIG_BOOT_PRINTK_DELAY is not set +# CONFIG_RCU_TORTURE_TEST is not set +# CONFIG_KPROBES_SANITY_TEST is not set +# CONFIG_BACKTRACE_SELF_TEST is not set +# CONFIG_LKDTM is not set +# CONFIG_FAULT_INJECTION is not set +# CONFIG_SAMPLES is not set + +# +# Security options +# +# CONFIG_KEYS is not set +# CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set +CONFIG_CRYPTO=y + +# +# Crypto core or helper +# +CONFIG_CRYPTO_ALGAPI=y +CONFIG_CRYPTO_AEAD=m +CONFIG_CRYPTO_BLKCIPHER=m +CONFIG_CRYPTO_HASH=m +CONFIG_CRYPTO_MANAGER=m +# CONFIG_CRYPTO_GF128MUL is not set +# CONFIG_CRYPTO_NULL is not set +# CONFIG_CRYPTO_CRYPTD is not set +CONFIG_CRYPTO_AUTHENC=m +# CONFIG_CRYPTO_TEST is not set + +# +# Authenticated Encryption with Associated Data +# +# CONFIG_CRYPTO_CCM is not set +# CONFIG_CRYPTO_GCM is not set +# CONFIG_CRYPTO_SEQIV is not set + +# +# Block modes +# +CONFIG_CRYPTO_CBC=m +# CONFIG_CRYPTO_CTR is not set +# CONFIG_CRYPTO_CTS is not set +# CONFIG_CRYPTO_ECB is not set +# CONFIG_CRYPTO_LRW is not set +# CONFIG_CRYPTO_PCBC is not set +# CONFIG_CRYPTO_XTS is not set + +# +# Hash modes +# +CONFIG_CRYPTO_HMAC=m +# CONFIG_CRYPTO_XCBC is not set + +# +# Digest +# +# CONFIG_CRYPTO_CRC32C is not set +# CONFIG_CRYPTO_MD4 is not set +CONFIG_CRYPTO_MD5=m +# CONFIG_CRYPTO_MICHAEL_MIC is not set +# CONFIG_CRYPTO_RMD128 is not set +# CONFIG_CRYPTO_RMD160 is not set +# CONFIG_CRYPTO_RMD256 is not set +# CONFIG_CRYPTO_RMD320 is not set +CONFIG_CRYPTO_SHA1=m +# CONFIG_CRYPTO_SHA256 is not set +# CONFIG_CRYPTO_SHA512 is not set +# CONFIG_CRYPTO_TGR192 is not set +# CONFIG_CRYPTO_WP512 is not set + +# +# Ciphers +# +# CONFIG_CRYPTO_AES is not set +# CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_ARC4 is not set +# CONFIG_CRYPTO_BLOWFISH is not set +# CONFIG_CRYPTO_CAMELLIA is not set +# CONFIG_CRYPTO_CAST5 is not set +# CONFIG_CRYPTO_CAST6 is not set +CONFIG_CRYPTO_DES=m +# CONFIG_CRYPTO_FCRYPT is not set +# CONFIG_CRYPTO_KHAZAD is not set +# CONFIG_CRYPTO_SALSA20 is not set +# CONFIG_CRYPTO_SEED is not set +# CONFIG_CRYPTO_SERPENT is not set +# CONFIG_CRYPTO_TEA is not set +# CONFIG_CRYPTO_TWOFISH is not set + +# +# Compression +# +CONFIG_CRYPTO_DEFLATE=y +CONFIG_CRYPTO_LZO=y +# CONFIG_CRYPTO_HW is not set + +# +# Library routines +# +CONFIG_BITREVERSE=y +# CONFIG_GENERIC_FIND_FIRST_BIT is not set +# CONFIG_GENERIC_FIND_NEXT_BIT is not set +CONFIG_CRC_CCITT=m +CONFIG_CRC16=y +CONFIG_CRC_T10DIF=m +CONFIG_CRC_ITU_T=m +CONFIG_CRC32=y +CONFIG_CRC7=m +# CONFIG_LIBCRC32C is not set +CONFIG_ZLIB_INFLATE=y +CONFIG_ZLIB_DEFLATE=y +CONFIG_LZO_COMPRESS=y +CONFIG_LZO_DECOMPRESS=y +CONFIG_GENERIC_ALLOCATOR=y +CONFIG_PLIST=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y +CONFIG_HAS_DMA=y diff --git a/arch/avr32/include/asm/a.out.h b/arch/avr32/include/asm/a.out.h deleted file mode 100644 index e46375a3..0000000 --- a/arch/avr32/include/asm/a.out.h +++ /dev/null @@ -1,20 +0,0 @@ -#ifndef __ASM_AVR32_A_OUT_H -#define __ASM_AVR32_A_OUT_H - -struct exec -{ - unsigned long a_info; /* Use macros N_MAGIC, etc for access */ - unsigned a_text; /* length of text, in bytes */ - unsigned a_data; /* length of data, in bytes */ - unsigned a_bss; /* length of uninitialized data area for file, in bytes */ - unsigned a_syms; /* length of symbol table data in file, in bytes */ - unsigned a_entry; /* start address */ - unsigned a_trsize; /* length of relocation info for text, in bytes */ - unsigned a_drsize; /* length of relocation info for data, in bytes */ -}; - -#define N_TRSIZE(a) ((a).a_trsize) -#define N_DRSIZE(a) ((a).a_drsize) -#define N_SYMSIZE(a) ((a).a_syms) - -#endif /* __ASM_AVR32_A_OUT_H */ diff --git a/arch/avr32/include/asm/atmel-mci.h b/arch/avr32/include/asm/atmel-mci.h index c2ea6e1..59f3fad 100644 --- a/arch/avr32/include/asm/atmel-mci.h +++ b/arch/avr32/include/asm/atmel-mci.h @@ -1,9 +1,39 @@ #ifndef __ASM_AVR32_ATMEL_MCI_H #define __ASM_AVR32_ATMEL_MCI_H -struct mci_platform_data { +#define ATMEL_MCI_MAX_NR_SLOTS 2 + +struct dma_slave; + +/** + * struct mci_slot_pdata - board-specific per-slot configuration + * @bus_width: Number of data lines wired up the slot + * @detect_pin: GPIO pin wired to the card detect switch + * @wp_pin: GPIO pin wired to the write protect sensor + * + * If a given slot is not present on the board, @bus_width should be + * set to 0. The other fields are ignored in this case. + * + * Any pins that aren't available should be set to a negative value. + * + * Note that support for multiple slots is experimental -- some cards + * might get upset if we don't get the clock management exactly right. + * But in most cases, it should work just fine. + */ +struct mci_slot_pdata { + unsigned int bus_width; int detect_pin; int wp_pin; }; +/** + * struct mci_platform_data - board-specific MMC/SDcard configuration + * @dma_slave: DMA slave interface to use in data transfers, or NULL. + * @slot: Per-slot configuration data. + */ +struct mci_platform_data { + struct dma_slave *dma_slave; + struct mci_slot_pdata slot[ATMEL_MCI_MAX_NR_SLOTS]; +}; + #endif /* __ASM_AVR32_ATMEL_MCI_H */ diff --git a/arch/avr32/include/asm/byteorder.h b/arch/avr32/include/asm/byteorder.h index d77b48b..8e3af02 100644 --- a/arch/avr32/include/asm/byteorder.h +++ b/arch/avr32/include/asm/byteorder.h @@ -7,6 +7,9 @@ #include <asm/types.h> #include <linux/compiler.h> +#define __BIG_ENDIAN +#define __SWAB_64_THRU_32__ + #ifdef __CHECKER__ extern unsigned long __builtin_bswap_32(unsigned long x); extern unsigned short __builtin_bswap_16(unsigned short x); @@ -17,15 +20,18 @@ extern unsigned short __builtin_bswap_16(unsigned short x); * the result. */ #if !(__GNUC__ == 4 && __GNUC_MINOR__ < 2) -#define __arch__swab32(x) __builtin_bswap_32(x) -#define __arch__swab16(x) __builtin_bswap_16(x) -#endif +static inline __attribute_const__ __u16 __arch_swab16(__u16 val) +{ + return __builtin_bswap_16(val); +} +#define __arch_swab16 __arch_swab16 -#if !defined(__STRICT_ANSI__) || defined(__KERNEL__) -# define __BYTEORDER_HAS_U64__ -# define __SWAB_64_THRU_32__ +static inline __attribute_const__ __u32 __arch_swab32(__u32 val) +{ + return __builtin_bswap_32(val); +} +#define __arch_swab32 __arch_swab32 #endif -#include <linux/byteorder/big_endian.h> - +#include <linux/byteorder.h> #endif /* __ASM_AVR32_BYTEORDER_H */ diff --git a/arch/avr32/include/asm/io.h b/arch/avr32/include/asm/io.h index a520f77..22c97ef 100644 --- a/arch/avr32/include/asm/io.h +++ b/arch/avr32/include/asm/io.h @@ -160,6 +160,14 @@ BUILDIO_IOPORT(l, u32) #define readw_relaxed readw #define readl_relaxed readl +#define readb_be __raw_readb +#define readw_be __raw_readw +#define readl_be __raw_readl + +#define writeb_be __raw_writeb +#define writew_be __raw_writew +#define writel_be __raw_writel + #define __BUILD_MEMORY_STRING(bwl, type) \ static inline void writes##bwl(volatile void __iomem *addr, \ const void *data, unsigned int count) \ diff --git a/arch/avr32/kernel/.gitignore b/arch/avr32/kernel/.gitignore new file mode 100644 index 0000000..c5f676c --- /dev/null +++ b/arch/avr32/kernel/.gitignore @@ -0,0 +1 @@ +vmlinux.lds diff --git a/arch/avr32/kernel/asm-offsets.c b/arch/avr32/kernel/asm-offsets.c index e4796c6..d6a8193 100644 --- a/arch/avr32/kernel/asm-offsets.c +++ b/arch/avr32/kernel/asm-offsets.c @@ -4,6 +4,8 @@ * to extract and format the required data. */ +#include <linux/mm.h> +#include <linux/sched.h> #include <linux/thread_info.h> #include <linux/kbuild.h> @@ -17,4 +19,8 @@ void foo(void) OFFSET(TI_rar_saved, thread_info, rar_saved); OFFSET(TI_rsr_saved, thread_info, rsr_saved); OFFSET(TI_restart_block, thread_info, restart_block); + BLANK(); + OFFSET(TSK_active_mm, task_struct, active_mm); + BLANK(); + OFFSET(MM_pgd, mm_struct, pgd); } diff --git a/arch/avr32/kernel/avr32_ksyms.c b/arch/avr32/kernel/avr32_ksyms.c index 84a7d44..11e310c 100644 --- a/arch/avr32/kernel/avr32_ksyms.c +++ b/arch/avr32/kernel/avr32_ksyms.c @@ -58,6 +58,7 @@ EXPORT_SYMBOL(find_first_zero_bit); EXPORT_SYMBOL(find_next_zero_bit); EXPORT_SYMBOL(find_first_bit); EXPORT_SYMBOL(find_next_bit); +EXPORT_SYMBOL(generic_find_next_le_bit); EXPORT_SYMBOL(generic_find_next_zero_le_bit); /* I/O primitives (lib/io-*.S) */ diff --git a/arch/avr32/kernel/entry-avr32b.S b/arch/avr32/kernel/entry-avr32b.S index 2b398ca..33d4937 100644 --- a/arch/avr32/kernel/entry-avr32b.S +++ b/arch/avr32/kernel/entry-avr32b.S @@ -334,9 +334,64 @@ save_full_context_ex: /* Low-level exception handlers */ handle_critical: + /* + * AT32AP700x errata: + * + * After a Java stack overflow or underflow trap, any CPU + * memory access may cause erratic behavior. This will happen + * when the four least significant bits of the JOSP system + * register contains any value between 9 and 15 (inclusive). + * + * Possible workarounds: + * - Don't use the Java Extension Module + * - Ensure that the stack overflow and underflow trap + * handlers do not do any memory access or trigger any + * exceptions before the overflow/underflow condition is + * cleared (by incrementing or decrementing the JOSP) + * - Make sure that JOSP does not contain any problematic + * value before doing any exception or interrupt + * processing. + * - Set up a critical exception handler which writes a + * known-to-be-safe value, e.g. 4, to JOSP before doing + * any further processing. + * + * We'll use the last workaround for now since we cannot + * guarantee that user space processes don't use Java mode. + * Non-well-behaving userland will be terminated with extreme + * prejudice. + */ +#ifdef CONFIG_CPU_AT32AP700X + /* + * There's a chance we can't touch memory, so temporarily + * borrow PTBR to save the stack pointer while we fix things + * up... + */ + mtsr SYSREG_PTBR, sp + mov sp, 4 + mtsr SYSREG_JOSP, sp + mfsr sp, SYSREG_PTBR + sub pc, -2 + + /* Push most of pt_regs on stack. We'll do the rest later */ sub sp, 4 - stmts --sp, r0-lr - rcall save_full_context_ex + pushm r0-r12 + + /* PTBR mirrors current_thread_info()->task->active_mm->pgd */ + get_thread_info r0 + ld.w r1, r0[TI_task] + ld.w r2, r1[TSK_active_mm] + ld.w r3, r2[MM_pgd] + mtsr SYSREG_PTBR, r3 +#else + sub sp, 4 + pushm r0-r12 +#endif + sub r0, sp, -(14 * 4) + mov r1, lr + mfsr r2, SYSREG_RAR_EX + mfsr r3, SYSREG_RSR_EX + pushm r0-r3 + mfsr r12, SYSREG_ECR mov r11, sp rcall do_critical_exception diff --git a/arch/avr32/kernel/process.c b/arch/avr32/kernel/process.c index 2c08ac9..134d530 100644 --- a/arch/avr32/kernel/process.c +++ b/arch/avr32/kernel/process.c @@ -9,6 +9,7 @@ #include <linux/module.h> #include <linux/kallsyms.h> #include <linux/fs.h> +#include <linux/pm.h> #include <linux/ptrace.h> #include <linux/reboot.h> #include <linux/tick.h> @@ -20,7 +21,7 @@ #include <mach/pm.h> -void (*pm_power_off)(void) = NULL; +void (*pm_power_off)(void); EXPORT_SYMBOL(pm_power_off); /* diff --git a/arch/avr32/kernel/setup.c b/arch/avr32/kernel/setup.c index d8e623c..5c70839 100644 --- a/arch/avr32/kernel/setup.c +++ b/arch/avr32/kernel/setup.c @@ -283,6 +283,25 @@ static int __init early_parse_fbmem(char *p) } early_param("fbmem", early_parse_fbmem); +/* + * Pick out the memory size. We look for mem=size@start, + * where start and size are "size[KkMmGg]" + */ +static int __init early_mem(char *p) +{ + resource_size_t size, start; + + start = system_ram->start; + size = memparse(p, &p); + if (*p == '@') + start = memparse(p + 1, &p); + + system_ram->start = start; + system_ram->end = system_ram->start + size - 1; + return 0; +} +early_param("mem", early_mem); + static int __init parse_tag_core(struct tag *tag) { if (tag->hdr.size > 2) { diff --git a/arch/avr32/kernel/syscall-stubs.S b/arch/avr32/kernel/syscall-stubs.S index 890286a..673178e 100644 --- a/arch/avr32/kernel/syscall-stubs.S +++ b/arch/avr32/kernel/syscall-stubs.S @@ -109,3 +109,12 @@ __sys_epoll_pwait: rcall sys_epoll_pwait sub sp, -4 popm pc + + .global __sys_sync_file_range + .type __sys_sync_file_range,@function +__sys_sync_file_range: + pushm lr + st.w --sp, ARG6 + rcall sys_sync_file_range + sub sp, -4 + popm pc diff --git a/arch/avr32/kernel/syscall_table.S b/arch/avr32/kernel/syscall_table.S index 478bda4..7ee0057 100644 --- a/arch/avr32/kernel/syscall_table.S +++ b/arch/avr32/kernel/syscall_table.S @@ -275,7 +275,7 @@ sys_call_table: .long sys_set_robust_list .long sys_get_robust_list /* 260 */ .long __sys_splice - .long sys_sync_file_range + .long __sys_sync_file_range .long sys_tee .long sys_vmsplice .long __sys_epoll_pwait /* 265 */ diff --git a/arch/avr32/kernel/traps.c b/arch/avr32/kernel/traps.c index b835c4c..0d98737 100644 --- a/arch/avr32/kernel/traps.c +++ b/arch/avr32/kernel/traps.c @@ -116,15 +116,15 @@ asmlinkage void do_nmi(unsigned long ecr, struct pt_regs *regs) switch (ret) { case NOTIFY_OK: case NOTIFY_STOP: - return; + break; case NOTIFY_BAD: die("Fatal Non-Maskable Interrupt", regs, SIGINT); default: + printk(KERN_ALERT "Got NMI, but nobody cared. Disabling...\n"); + nmi_disable(); break; } - - printk(KERN_ALERT "Got NMI, but nobody cared. Disabling...\n"); - nmi_disable(); + nmi_exit(); } asmlinkage void do_critical_exception(unsigned long ecr, struct pt_regs *regs) diff --git a/arch/avr32/lib/findbit.S b/arch/avr32/lib/findbit.S index c6b91de..997b33b 100644 --- a/arch/avr32/lib/findbit.S +++ b/arch/avr32/lib/findbit.S @@ -123,6 +123,36 @@ ENTRY(find_next_bit) brgt 1b retal r11 +ENTRY(generic_find_next_le_bit) + lsr r8, r10, 5 + sub r9, r11, r10 + retle r11 + + lsl r8, 2 + add r12, r8 + andl r10, 31, COH + breq 1f + + /* offset is not word-aligned. Handle the first (32 - r10) bits */ + ldswp.w r8, r12[0] + sub r12, -4 + lsr r8, r8, r10 + brne .L_found + + /* r9 = r9 - (32 - r10) = r9 + r10 - 32 */ + add r9, r10 + sub r9, 32 + retle r11 + + /* Main loop. offset must be word-aligned */ +1: ldswp.w r8, r12[0] + cp.w r8, 0 + brne .L_found + sub r12, -4 + sub r9, 32 + brgt 1b + retal r11 + ENTRY(generic_find_next_zero_le_bit) lsr r8, r10, 5 sub r9, r11, r10 diff --git a/arch/avr32/mach-at32ap/Makefile b/arch/avr32/mach-at32ap/Makefile index d5018e2..514c9a9 100644 --- a/arch/avr32/mach-at32ap/Makefile +++ b/arch/avr32/mach-at32ap/Makefile @@ -1,4 +1,5 @@ obj-y += pdc.o clock.o intc.o extint.o pio.o hsmc.o +obj-y += hmatrix.o obj-$(CONFIG_CPU_AT32AP700X) += at32ap700x.o pm-at32ap700x.o obj-$(CONFIG_CPU_FREQ_AT32AP) += cpufreq.o obj-$(CONFIG_PM) += pm.o diff --git a/arch/avr32/mach-at32ap/at32ap700x.c b/arch/avr32/mach-at32ap/at32ap700x.c index 92bfb4d..813b684 100644 --- a/arch/avr32/mach-at32ap/at32ap700x.c +++ b/arch/avr32/mach-at32ap/at32ap700x.c @@ -22,13 +22,13 @@ #include <mach/at32ap700x.h> #include <mach/board.h> +#include <mach/hmatrix.h> #include <mach/portmux.h> #include <mach/sram.h> #include <video/atmel_lcdc.h> #include "clock.h" -#include "hmatrix.h" #include "pio.h" #include "pm.h" @@ -82,8 +82,9 @@ static struct platform_device _name##_id##_device = { \ .num_resources = ARRAY_SIZE(_name##_id##_resource), \ } -#define select_peripheral(pin, periph, flags) \ - at32_select_periph(GPIO_PIN_##pin, GPIO_##periph, flags) +#define select_peripheral(port, pin_mask, periph, flags) \ + at32_select_periph(GPIO_##port##_BASE, pin_mask, \ + GPIO_##periph, flags) #define DEV_CLK(_name, devname, bus, _index) \ static struct clk devname##_##_name = { \ @@ -725,7 +726,7 @@ static struct clk pico_clk = { * HMATRIX * -------------------------------------------------------------------- */ -static struct clk hmatrix_clk = { +struct clk at32_hmatrix_clk = { .name = "hmatrix_clk", .parent = &pbb_clk, .mode = pbb_clk_mode, @@ -733,12 +734,6 @@ static struct clk hmatrix_clk = { .index = 2, .users = 1, }; -#define HMATRIX_BASE ((void __iomem *)0xfff00800) - -#define hmatrix_readl(reg) \ - __raw_readl((HMATRIX_BASE) + HMATRIX_##reg) -#define hmatrix_writel(reg,value) \ - __raw_writel((value), (HMATRIX_BASE) + HMATRIX_##reg) /* * Set bits in the HMATRIX Special Function Register (SFR) used by the @@ -748,13 +743,7 @@ static struct clk hmatrix_clk = { */ static inline void set_ebi_sfr_bits(u32 mask) { - u32 sfr; - - clk_enable(&hmatrix_clk); - sfr = hmatrix_readl(SFR4); - sfr |= mask; - hmatrix_writel(SFR4, sfr); - clk_disable(&hmatrix_clk); + hmatrix_sfr_set_bits(HMATRIX_SLAVE_EBI, mask); } /* -------------------------------------------------------------------- @@ -883,6 +872,7 @@ static struct clk atmel_psif1_pclk = { struct platform_device *__init at32_add_device_psif(unsigned int id) { struct platform_device *pdev; + u32 pin_mask; if (!(id == 0 || id == 1)) return NULL; @@ -893,20 +883,22 @@ struct platform_device *__init at32_add_device_psif(unsigned int id) switch (id) { case 0: + pin_mask = (1 << 8) | (1 << 9); /* CLOCK & DATA */ + if (platform_device_add_resources(pdev, atmel_psif0_resource, ARRAY_SIZE(atmel_psif0_resource))) goto err_add_resources; atmel_psif0_pclk.dev = &pdev->dev; - select_peripheral(PA(8), PERIPH_A, 0); /* CLOCK */ - select_peripheral(PA(9), PERIPH_A, 0); /* DATA */ + select_peripheral(PIOA, pin_mask, PERIPH_A, 0); break; case 1: + pin_mask = (1 << 11) | (1 << 12); /* CLOCK & DATA */ + if (platform_device_add_resources(pdev, atmel_psif1_resource, ARRAY_SIZE(atmel_psif1_resource))) goto err_add_resources; atmel_psif1_pclk.dev = &pdev->dev; - select_peripheral(PB(11), PERIPH_A, 0); /* CLOCK */ - select_peripheral(PB(12), PERIPH_A, 0); /* DATA */ + select_peripheral(PIOB, pin_mask, PERIPH_A, 0); break; default: return NULL; @@ -970,26 +962,30 @@ DEV_CLK(usart, atmel_usart3, pba, 6); static inline void configure_usart0_pins(void) { - select_peripheral(PA(8), PERIPH_B, 0); /* RXD */ - select_peripheral(PA(9), PERIPH_B, 0); /* TXD */ + u32 pin_mask = (1 << 8) | (1 << 9); /* RXD & TXD */ + + select_peripheral(PIOA, pin_mask, PERIPH_B, 0); } static inline void configure_usart1_pins(void) { - select_peripheral(PA(17), PERIPH_A, 0); /* RXD */ - select_peripheral(PA(18), PERIPH_A, 0); /* TXD */ + u32 pin_mask = (1 << 17) | (1 << 18); /* RXD & TXD */ + + select_peripheral(PIOA, pin_mask, PERIPH_A, 0); } static inline void configure_usart2_pins(void) { - select_peripheral(PB(26), PERIPH_B, 0); /* RXD */ - select_peripheral(PB(27), PERIPH_B, 0); /* TXD */ + u32 pin_mask = (1 << 26) | (1 << 27); /* RXD & TXD */ + + select_peripheral(PIOB, pin_mask, PERIPH_B, 0); } static inline void configure_usart3_pins(void) { - select_peripheral(PB(18), PERIPH_B, 0); /* RXD */ - select_peripheral(PB(17), PERIPH_B, 0); /* TXD */ + u32 pin_mask = (1 << 18) | (1 << 17); /* RXD & TXD */ + + select_peripheral(PIOB, pin_mask, PERIPH_B, 0); } static struct platform_device *__initdata at32_usarts[4]; @@ -1069,59 +1065,69 @@ struct platform_device *__init at32_add_device_eth(unsigned int id, struct eth_platform_data *data) { struct platform_device *pdev; + u32 pin_mask; switch (id) { case 0: pdev = &macb0_device; - select_peripheral(PC(3), PERIPH_A, 0); /* TXD0 */ - select_peripheral(PC(4), PERIPH_A, 0); /* TXD1 */ - select_peripheral(PC(7), PERIPH_A, 0); /* TXEN */ - select_peripheral(PC(8), PERIPH_A, 0); /* TXCK */ - select_peripheral(PC(9), PERIPH_A, 0); /* RXD0 */ - select_peripheral(PC(10), PERIPH_A, 0); /* RXD1 */ - select_peripheral(PC(13), PERIPH_A, 0); /* RXER */ - select_peripheral(PC(15), PERIPH_A, 0); /* RXDV */ - select_peripheral(PC(16), PERIPH_A, 0); /* MDC */ - select_peripheral(PC(17), PERIPH_A, 0); /* MDIO */ + pin_mask = (1 << 3); /* TXD0 */ + pin_mask |= (1 << 4); /* TXD1 */ + pin_mask |= (1 << 7); /* TXEN */ + pin_mask |= (1 << 8); /* TXCK */ + pin_mask |= (1 << 9); /* RXD0 */ + pin_mask |= (1 << 10); /* RXD1 */ + pin_mask |= (1 << 13); /* RXER */ + pin_mask |= (1 << 15); /* RXDV */ + pin_mask |= (1 << 16); /* MDC */ + pin_mask |= (1 << 17); /* MDIO */ if (!data->is_rmii) { - select_peripheral(PC(0), PERIPH_A, 0); /* COL */ - select_peripheral(PC(1), PERIPH_A, 0); /* CRS */ - select_peripheral(PC(2), PERIPH_A, 0); /* TXER */ - select_peripheral(PC(5), PERIPH_A, 0); /* TXD2 */ - select_peripheral(PC(6), PERIPH_A, 0); /* TXD3 */ - select_peripheral(PC(11), PERIPH_A, 0); /* RXD2 */ - select_peripheral(PC(12), PERIPH_A, 0); /* RXD3 */ - select_peripheral(PC(14), PERIPH_A, 0); /* RXCK */ - select_peripheral(PC(18), PERIPH_A, 0); /* SPD */ + pin_mask |= (1 << 0); /* COL */ + pin_mask |= (1 << 1); /* CRS */ + pin_mask |= (1 << 2); /* TXER */ + pin_mask |= (1 << 5); /* TXD2 */ + pin_mask |= (1 << 6); /* TXD3 */ + pin_mask |= (1 << 11); /* RXD2 */ + pin_mask |= (1 << 12); /* RXD3 */ + pin_mask |= (1 << 14); /* RXCK */ + pin_mask |= (1 << 18); /* SPD */ } + + select_peripheral(PIOC, pin_mask, PERIPH_A, 0); + break; case 1: pdev = &macb1_device; - select_peripheral(PD(13), PERIPH_B, 0); /* TXD0 */ - select_peripheral(PD(14), PERIPH_B, 0); /* TXD1 */ - select_peripheral(PD(11), PERIPH_B, 0); /* TXEN */ - select_peripheral(PD(12), PERIPH_B, 0); /* TXCK */ - select_peripheral(PD(10), PERIPH_B, 0); /* RXD0 */ - select_peripheral(PD(6), PERIPH_B, 0); /* RXD1 */ - select_peripheral(PD(5), PERIPH_B, 0); /* RXER */ - select_peripheral(PD(4), PERIPH_B, 0); /* RXDV */ - select_peripheral(PD(3), PERIPH_B, 0); /* MDC */ - select_peripheral(PD(2), PERIPH_B, 0); /* MDIO */ + pin_mask = (1 << 13); /* TXD0 */ + pin_mask |= (1 << 14); /* TXD1 */ + pin_mask |= (1 << 11); /* TXEN */ + pin_mask |= (1 << 12); /* TXCK */ + pin_mask |= (1 << 10); /* RXD0 */ + pin_mask |= (1 << 6); /* RXD1 */ + pin_mask |= (1 << 5); /* RXER */ + pin_mask |= (1 << 4); /* RXDV */ + pin_mask |= (1 << 3); /* MDC */ + pin_mask |= (1 << 2); /* MDIO */ + + if (!data->is_rmii) + pin_mask |= (1 << 15); /* SPD */ + + select_peripheral(PIOD, pin_mask, PERIPH_B, 0); if (!data->is_rmii) { - select_peripheral(PC(19), PERIPH_B, 0); /* COL */ - select_peripheral(PC(23), PERIPH_B, 0); /* CRS */ - select_peripheral(PC(26), PERIPH_B, 0); /* TXER */ - select_peripheral(PC(27), PERIPH_B, 0); /* TXD2 */ - select_peripheral(PC(28), PERIPH_B, 0); /* TXD3 */ - select_peripheral(PC(29), PERIPH_B, 0); /* RXD2 */ - select_peripheral(PC(30), PERIPH_B, 0); /* RXD3 */ - select_peripheral(PC(24), PERIPH_B, 0); /* RXCK */ - select_peripheral(PD(15), PERIPH_B, 0); /* SPD */ + pin_mask = (1 << 19); /* COL */ + pin_mask |= (1 << 23); /* CRS */ + pin_mask |= (1 << 26); /* TXER */ + pin_mask |= (1 << 27); /* TXD2 */ + pin_mask |= (1 << 28); /* TXD3 */ + pin_mask |= (1 << 29); /* RXD2 */ + pin_mask |= (1 << 30); /* RXD3 */ + pin_mask |= (1 << 24); /* RXCK */ + + select_peripheral(PIOC, pin_mask, PERIPH_B, 0); } break; @@ -1189,23 +1195,28 @@ at32_add_device_spi(unsigned int id, struct spi_board_info *b, unsigned int n) { GPIO_PIN_PB(2), GPIO_PIN_PB(3), GPIO_PIN_PB(4), GPIO_PIN_PA(27), }; struct platform_device *pdev; + u32 pin_mask; switch (id) { case 0: pdev = &atmel_spi0_device; + pin_mask = (1 << 1) | (1 << 2); /* MOSI & SCK */ + /* pullup MISO so a level is always defined */ - select_peripheral(PA(0), PERIPH_A, AT32_GPIOF_PULLUP); - select_peripheral(PA(1), PERIPH_A, 0); /* MOSI */ - select_peripheral(PA(2), PERIPH_A, 0); /* SCK */ + select_peripheral(PIOA, (1 << 0), PERIPH_A, AT32_GPIOF_PULLUP); + select_peripheral(PIOA, pin_mask, PERIPH_A, 0); + at32_spi_setup_slaves(0, b, n, spi0_pins); break; case 1: pdev = &atmel_spi1_device; + pin_mask = (1 << 1) | (1 << 5); /* MOSI */ + /* pullup MISO so a level is always defined */ - select_peripheral(PB(0), PERIPH_B, AT32_GPIOF_PULLUP); - select_peripheral(PB(1), PERIPH_B, 0); /* MOSI */ - select_peripheral(PB(5), PERIPH_B, 0); /* SCK */ + select_peripheral(PIOB, (1 << 0), PERIPH_B, AT32_GPIOF_PULLUP); + select_peripheral(PIOB, pin_mask, PERIPH_B, 0); + at32_spi_setup_slaves(1, b, n, spi1_pins); break; @@ -1238,6 +1249,7 @@ struct platform_device *__init at32_add_device_twi(unsigned int id, unsigned int n) { struct platform_device *pdev; + u32 pin_mask; if (id != 0) return NULL; @@ -1250,8 +1262,9 @@ struct platform_device *__init at32_add_device_twi(unsigned int id, ARRAY_SIZE(atmel_twi0_resource))) goto err_add_resources; - select_peripheral(PA(6), PERIPH_A, 0); /* SDA */ - select_peripheral(PA(7), PERIPH_A, 0); /* SDL */ + pin_mask = (1 << 6) | (1 << 7); /* SDA & SDL */ + + select_peripheral(PIOA, pin_mask, PERIPH_A, 0); atmel_twi0_pclk.dev = &pdev->dev; @@ -1284,10 +1297,16 @@ static struct clk atmel_mci0_pclk = { struct platform_device *__init at32_add_device_mci(unsigned int id, struct mci_platform_data *data) { - struct mci_platform_data _data; struct platform_device *pdev; + struct dw_dma_slave *dws; + u32 pioa_mask; + u32 piob_mask; - if (id != 0) + if (id != 0 || !data) + return NULL; + + /* Must have at least one usable slot */ + if (!data->slot[0].bus_width && !data->slot[1].bus_width) return NULL; pdev = platform_device_alloc("atmel_mci", id); @@ -1298,28 +1317,80 @@ at32_add_device_mci(unsigned int id, struct mci_platform_data *data) ARRAY_SIZE(atmel_mci0_resource))) goto fail; - if (!data) { - data = &_data; - memset(data, -1, sizeof(struct mci_platform_data)); - data->detect_pin = GPIO_PIN_NONE; - data->wp_pin = GPIO_PIN_NONE; - } + if (data->dma_slave) + dws = kmemdup(to_dw_dma_slave(data->dma_slave), + sizeof(struct dw_dma_slave), GFP_KERNEL); + else + dws = kzalloc(sizeof(struct dw_dma_slave), GFP_KERNEL); + + dws->slave.dev = &pdev->dev; + dws->slave.dma_dev = &dw_dmac0_device.dev; + dws->slave.reg_width = DMA_SLAVE_WIDTH_32BIT; + dws->cfg_hi = (DWC_CFGH_SRC_PER(0) + | DWC_CFGH_DST_PER(1)); + dws->cfg_lo &= ~(DWC_CFGL_HS_DST_POL + | DWC_CFGL_HS_SRC_POL); + + data->dma_slave = &dws->slave; if (platform_device_add_data(pdev, data, sizeof(struct mci_platform_data))) goto fail; - select_peripheral(PA(10), PERIPH_A, 0); /* CLK */ - select_peripheral(PA(11), PERIPH_A, 0); /* CMD */ - select_peripheral(PA(12), PERIPH_A, 0); /* DATA0 */ - select_peripheral(PA(13), PERIPH_A, 0); /* DATA1 */ - select_peripheral(PA(14), PERIPH_A, 0); /* DATA2 */ - select_peripheral(PA(15), PERIPH_A, 0); /* DATA3 */ + /* CLK line is common to both slots */ + pioa_mask = 1 << 10; - if (gpio_is_valid(data->detect_pin)) - at32_select_gpio(data->detect_pin, 0); - if (gpio_is_valid(data->wp_pin)) - at32_select_gpio(data->wp_pin, 0); + switch (data->slot[0].bus_width) { + case 4: + pioa_mask |= 1 << 13; /* DATA1 */ + pioa_mask |= 1 << 14; /* DATA2 */ + pioa_mask |= 1 << 15; /* DATA3 */ + /* fall through */ + case 1: + pioa_mask |= 1 << 11; /* CMD */ + pioa_mask |= 1 << 12; /* DATA0 */ + + if (gpio_is_valid(data->slot[0].detect_pin)) + at32_select_gpio(data->slot[0].detect_pin, 0); + if (gpio_is_valid(data->slot[0].wp_pin)) + at32_select_gpio(data->slot[0].wp_pin, 0); + break; + case 0: + /* Slot is unused */ + break; + default: + goto fail; + } + + select_peripheral(PIOA, pioa_mask, PERIPH_A, 0); + piob_mask = 0; + + switch (data->slot[1].bus_width) { + case 4: + piob_mask |= 1 << 8; /* DATA1 */ + piob_mask |= 1 << 9; /* DATA2 */ + piob_mask |= 1 << 10; /* DATA3 */ + /* fall through */ + case 1: + piob_mask |= 1 << 6; /* CMD */ + piob_mask |= 1 << 7; /* DATA0 */ + select_peripheral(PIOB, piob_mask, PERIPH_B, 0); + + if (gpio_is_valid(data->slot[1].detect_pin)) + at32_select_gpio(data->slot[1].detect_pin, 0); + if (gpio_is_valid(data->slot[1].wp_pin)) + at32_select_gpio(data->slot[1].wp_pin, 0); + break; + case 0: + /* Slot is unused */ + break; + default: + if (!data->slot[0].bus_width) + goto fail; + + data->slot[1].bus_width = 0; + break; + } atmel_mci0_pclk.dev = &pdev->dev; @@ -1365,13 +1436,14 @@ static struct clk atmel_lcdfb0_pixclk = { struct platform_device *__init at32_add_device_lcdc(unsigned int id, struct atmel_lcdfb_info *data, unsigned long fbmem_start, unsigned long fbmem_len, - unsigned int pin_config) + u64 pin_mask) { struct platform_device *pdev; struct atmel_lcdfb_info *info; struct fb_monspecs *monspecs; struct fb_videomode *modedb; unsigned int modedb_size; + u32 portc_mask, portd_mask, porte_mask; /* * Do a deep copy of the fb data, monspecs and modedb. Make @@ -1393,76 +1465,21 @@ at32_add_device_lcdc(unsigned int id, struct atmel_lcdfb_info *data, case 0: pdev = &atmel_lcdfb0_device; - switch (pin_config) { - case 0: - select_peripheral(PC(19), PERIPH_A, 0); /* CC */ - select_peripheral(PC(20), PERIPH_A, 0); /* HSYNC */ - select_peripheral(PC(21), PERIPH_A, 0); /* PCLK */ - select_peripheral(PC(22), PERIPH_A, 0); /* VSYNC */ - select_peripheral(PC(23), PERIPH_A, 0); /* DVAL */ - select_peripheral(PC(24), PERIPH_A, 0); /* MODE */ - select_peripheral(PC(25), PERIPH_A, 0); /* PWR */ - select_peripheral(PC(26), PERIPH_A, 0); /* DATA0 */ - select_peripheral(PC(27), PERIPH_A, 0); /* DATA1 */ - select_peripheral(PC(28), PERIPH_A, 0); /* DATA2 */ - select_peripheral(PC(29), PERIPH_A, 0); /* DATA3 */ - select_peripheral(PC(30), PERIPH_A, 0); /* DATA4 */ - select_peripheral(PC(31), PERIPH_A, 0); /* DATA5 */ - select_peripheral(PD(0), PERIPH_A, 0); /* DATA6 */ - select_peripheral(PD(1), PERIPH_A, 0); /* DATA7 */ - select_peripheral(PD(2), PERIPH_A, 0); /* DATA8 */ - select_peripheral(PD(3), PERIPH_A, 0); /* DATA9 */ - select_peripheral(PD(4), PERIPH_A, 0); /* DATA10 */ - select_peripheral(PD(5), PERIPH_A, 0); /* DATA11 */ - select_peripheral(PD(6), PERIPH_A, 0); /* DATA12 */ - select_peripheral(PD(7), PERIPH_A, 0); /* DATA13 */ - select_peripheral(PD(8), PERIPH_A, 0); /* DATA14 */ - select_peripheral(PD(9), PERIPH_A, 0); /* DATA15 */ - select_peripheral(PD(10), PERIPH_A, 0); /* DATA16 */ - select_peripheral(PD(11), PERIPH_A, 0); /* DATA17 */ - select_peripheral(PD(12), PERIPH_A, 0); /* DATA18 */ - select_peripheral(PD(13), PERIPH_A, 0); /* DATA19 */ - select_peripheral(PD(14), PERIPH_A, 0); /* DATA20 */ - select_peripheral(PD(15), PERIPH_A, 0); /* DATA21 */ - select_peripheral(PD(16), PERIPH_A, 0); /* DATA22 */ - select_peripheral(PD(17), PERIPH_A, 0); /* DATA23 */ - break; - case 1: - select_peripheral(PE(0), PERIPH_B, 0); /* CC */ - select_peripheral(PC(20), PERIPH_A, 0); /* HSYNC */ - select_peripheral(PC(21), PERIPH_A, 0); /* PCLK */ - select_peripheral(PC(22), PERIPH_A, 0); /* VSYNC */ - select_peripheral(PE(1), PERIPH_B, 0); /* DVAL */ - select_peripheral(PE(2), PERIPH_B, 0); /* MODE */ - select_peripheral(PC(25), PERIPH_A, 0); /* PWR */ - select_peripheral(PE(3), PERIPH_B, 0); /* DATA0 */ - select_peripheral(PE(4), PERIPH_B, 0); /* DATA1 */ - select_peripheral(PE(5), PERIPH_B, 0); /* DATA2 */ - select_peripheral(PE(6), PERIPH_B, 0); /* DATA3 */ - select_peripheral(PE(7), PERIPH_B, 0); /* DATA4 */ - select_peripheral(PC(31), PERIPH_A, 0); /* DATA5 */ - select_peripheral(PD(0), PERIPH_A, 0); /* DATA6 */ - select_peripheral(PD(1), PERIPH_A, 0); /* DATA7 */ - select_peripheral(PE(8), PERIPH_B, 0); /* DATA8 */ - select_peripheral(PE(9), PERIPH_B, 0); /* DATA9 */ - select_peripheral(PE(10), PERIPH_B, 0); /* DATA10 */ - select_peripheral(PE(11), PERIPH_B, 0); /* DATA11 */ - select_peripheral(PE(12), PERIPH_B, 0); /* DATA12 */ - select_peripheral(PD(7), PERIPH_A, 0); /* DATA13 */ - select_peripheral(PD(8), PERIPH_A, 0); /* DATA14 */ - select_peripheral(PD(9), PERIPH_A, 0); /* DATA15 */ - select_peripheral(PE(13), PERIPH_B, 0); /* DATA16 */ - select_peripheral(PE(14), PERIPH_B, 0); /* DATA17 */ - select_peripheral(PE(15), PERIPH_B, 0); /* DATA18 */ - select_peripheral(PE(16), PERIPH_B, 0); /* DATA19 */ - select_peripheral(PE(17), PERIPH_B, 0); /* DATA20 */ - select_peripheral(PE(18), PERIPH_B, 0); /* DATA21 */ - select_peripheral(PD(16), PERIPH_A, 0); /* DATA22 */ - select_peripheral(PD(17), PERIPH_A, 0); /* DATA23 */ - break; - default: - goto err_invalid_id; - } + if (pin_mask == 0ULL) + /* Default to "full" lcdc control signals and 24bit */ + pin_mask = ATMEL_LCDC_PRI_24BIT | ATMEL_LCDC_PRI_CONTROL; + + /* LCDC on port C */ + portc_mask = (pin_mask & 0xfff80000) >> 19; + select_peripheral(PIOC, portc_mask, PERIPH_A, 0); + + /* LCDC on port D */ + portd_mask = pin_mask & 0x0003ffff; + select_peripheral(PIOD, portd_mask, PERIPH_A, 0); + + /* LCDC on port E */ + porte_mask = (pin_mask >> 32) & 0x0007ffff; + select_peripheral(PIOE, porte_mask, PERIPH_B, 0); clk_set_parent(&atmel_lcdfb0_pixclk, &pll0); clk_set_rate(&atmel_lcdfb0_pixclk, clk_get_rate(&pll0)); @@ -1511,6 +1528,7 @@ static struct clk atmel_pwm0_mck = { struct platform_device *__init at32_add_device_pwm(u32 mask) { struct platform_device *pdev; + u32 pin_mask; if (!mask) return NULL; @@ -1526,14 +1544,21 @@ struct platform_device *__init at32_add_device_pwm(u32 mask) if (platform_device_add_data(pdev, &mask, sizeof(mask))) goto out_free_pdev; + pin_mask = 0; if (mask & (1 << 0)) - select_peripheral(PA(28), PERIPH_A, 0); + pin_mask |= (1 << 28); if (mask & (1 << 1)) - select_peripheral(PA(29), PERIPH_A, 0); + pin_mask |= (1 << 29); + if (pin_mask > 0) + select_peripheral(PIOA, pin_mask, PERIPH_A, 0); + + pin_mask = 0; if (mask & (1 << 2)) - select_peripheral(PA(21), PERIPH_B, 0); + pin_mask |= (1 << 21); if (mask & (1 << 3)) - select_peripheral(PA(22), PERIPH_B, 0); + pin_mask |= (1 << 22); + if (pin_mask > 0) + select_peripheral(PIOA, pin_mask, PERIPH_B, 0); atmel_pwm0_mck.dev = &pdev->dev; @@ -1574,52 +1599,65 @@ struct platform_device *__init at32_add_device_ssc(unsigned int id, unsigned int flags) { struct platform_device *pdev; + u32 pin_mask = 0; switch (id) { case 0: pdev = &ssc0_device; if (flags & ATMEL_SSC_RF) - select_peripheral(PA(21), PERIPH_A, 0); /* RF */ + pin_mask |= (1 << 21); /* RF */ if (flags & ATMEL_SSC_RK) - select_peripheral(PA(22), PERIPH_A, 0); /* RK */ + pin_mask |= (1 << 22); /* RK */ if (flags & ATMEL_SSC_TK) - select_peripheral(PA(23), PERIPH_A, 0); /* TK */ + pin_mask |= (1 << 23); /* TK */ if (flags & ATMEL_SSC_TF) - select_peripheral(PA(24), PERIPH_A, 0); /* TF */ + pin_mask |= (1 << 24); /* TF */ if (flags & ATMEL_SSC_TD) - select_peripheral(PA(25), PERIPH_A, 0); /* TD */ + pin_mask |= (1 << 25); /* TD */ if (flags & ATMEL_SSC_RD) - select_peripheral(PA(26), PERIPH_A, 0); /* RD */ + pin_mask |= (1 << 26); /* RD */ + + if (pin_mask > 0) + select_peripheral(PIOA, pin_mask, PERIPH_A, 0); + break; case 1: pdev = &ssc1_device; if (flags & ATMEL_SSC_RF) - select_peripheral(PA(0), PERIPH_B, 0); /* RF */ + pin_mask |= (1 << 0); /* RF */ if (flags & ATMEL_SSC_RK) - select_peripheral(PA(1), PERIPH_B, 0); /* RK */ + pin_mask |= (1 << 1); /* RK */ if (flags & ATMEL_SSC_TK) - select_peripheral(PA(2), PERIPH_B, 0); /* TK */ + pin_mask |= (1 << 2); /* TK */ if (flags & ATMEL_SSC_TF) - select_peripheral(PA(3), PERIPH_B, 0); /* TF */ + pin_mask |= (1 << 3); /* TF */ if (flags & ATMEL_SSC_TD) - select_peripheral(PA(4), PERIPH_B, 0); /* TD */ + pin_mask |= (1 << 4); /* TD */ if (flags & ATMEL_SSC_RD) - select_peripheral(PA(5), PERIPH_B, 0); /* RD */ + pin_mask |= (1 << 5); /* RD */ + + if (pin_mask > 0) + select_peripheral(PIOA, pin_mask, PERIPH_B, 0); + break; case 2: pdev = &ssc2_device; if (flags & ATMEL_SSC_TD) - select_peripheral(PB(13), PERIPH_A, 0); /* TD */ + pin_mask |= (1 << 13); /* TD */ if (flags & ATMEL_SSC_RD) - select_peripheral(PB(14), PERIPH_A, 0); /* RD */ + pin_mask |= (1 << 14); /* RD */ if (flags & ATMEL_SSC_TK) - select_peripheral(PB(15), PERIPH_A, 0); /* TK */ + pin_mask |= (1 << 15); /* TK */ if (flags & ATMEL_SSC_TF) - select_peripheral(PB(16), PERIPH_A, 0); /* TF */ + pin_mask |= (1 << 16); /* TF */ if (flags & ATMEL_SSC_RF) - select_peripheral(PB(17), PERIPH_A, 0); /* RF */ + pin_mask |= (1 << 17); /* RF */ if (flags & ATMEL_SSC_RK) - select_peripheral(PB(18), PERIPH_A, 0); /* RK */ + pin_mask |= (1 << 18); /* RK */ + + if (pin_mask > 0) + select_peripheral(PIOB, pin_mask, PERIPH_A, 0); + break; default: return NULL; @@ -1757,14 +1795,15 @@ static int __init at32_init_ide_or_cf(struct platform_device *pdev, unsigned int cs, unsigned int extint) { static unsigned int extint_pin_map[4] __initdata = { - GPIO_PIN_PB(25), - GPIO_PIN_PB(26), - GPIO_PIN_PB(27), - GPIO_PIN_PB(28), + (1 << 25), + (1 << 26), + (1 << 27), + (1 << 28), }; static bool common_pins_initialized __initdata = false; unsigned int extint_pin; int ret; + u32 pin_mask; if (extint >= ARRAY_SIZE(extint_pin_map)) return -EINVAL; @@ -1778,8 +1817,9 @@ static int __init at32_init_ide_or_cf(struct platform_device *pdev, if (ret) return ret; - select_peripheral(PE(21), PERIPH_A, 0); /* NCS4 -> OE_N */ - set_ebi_sfr_bits(HMATRIX_BIT(CS4A)); + /* NCS4 -> OE_N */ + select_peripheral(PIOE, (1 << 21), PERIPH_A, 0); + hmatrix_sfr_set_bits(HMATRIX_SLAVE_EBI, HMATRIX_EBI_CF0_ENABLE); break; case 5: ret = platform_device_add_resources(pdev, @@ -1788,22 +1828,26 @@ static int __init at32_init_ide_or_cf(struct platform_device *pdev, if (ret) return ret; - select_peripheral(PE(22), PERIPH_A, 0); /* NCS5 -> OE_N */ - set_ebi_sfr_bits(HMATRIX_BIT(CS5A)); + /* NCS5 -> OE_N */ + select_peripheral(PIOE, (1 << 22), PERIPH_A, 0); + hmatrix_sfr_set_bits(HMATRIX_SLAVE_EBI, HMATRIX_EBI_CF1_ENABLE); break; default: return -EINVAL; } if (!common_pins_initialized) { - select_peripheral(PE(19), PERIPH_A, 0); /* CFCE1 -> CS0_N */ - select_peripheral(PE(20), PERIPH_A, 0); /* CFCE2 -> CS1_N */ - select_peripheral(PE(23), PERIPH_A, 0); /* CFRNW -> DIR */ - select_peripheral(PE(24), PERIPH_A, 0); /* NWAIT <- IORDY */ + pin_mask = (1 << 19); /* CFCE1 -> CS0_N */ + pin_mask |= (1 << 20); /* CFCE2 -> CS1_N */ + pin_mask |= (1 << 23); /* CFRNW -> DIR */ + pin_mask |= (1 << 24); /* NWAIT <- IORDY */ + + select_peripheral(PIOE, pin_mask, PERIPH_A, 0); + common_pins_initialized = true; } - at32_select_periph(extint_pin, GPIO_PERIPH_A, AT32_GPIOF_DEGLITCH); + select_peripheral(PIOB, extint_pin, PERIPH_A, AT32_GPIOF_DEGLITCH); pdev->resource[1].start = EIM_IRQ_BASE + extint; pdev->resource[1].end = pdev->resource[1].start; @@ -1905,7 +1949,7 @@ at32_add_device_nand(unsigned int id, struct atmel_nand_data *data) sizeof(struct atmel_nand_data))) goto fail; - set_ebi_sfr_bits(HMATRIX_BIT(CS3A)); + hmatrix_sfr_set_bits(HMATRIX_SLAVE_EBI, HMATRIX_EBI_NAND_ENABLE); if (data->enable_pin) at32_select_gpio(data->enable_pin, AT32_GPIOF_OUTPUT | AT32_GPIOF_HIGH); @@ -1942,6 +1986,7 @@ at32_add_device_ac97c(unsigned int id, struct ac97c_platform_data *data) { struct platform_device *pdev; struct ac97c_platform_data _data; + u32 pin_mask; if (id != 0) return NULL; @@ -1968,10 +2013,10 @@ at32_add_device_ac97c(unsigned int id, struct ac97c_platform_data *data) sizeof(struct ac97c_platform_data))) goto fail; - select_peripheral(PB(20), PERIPH_B, 0); /* SDO */ - select_peripheral(PB(21), PERIPH_B, 0); /* SYNC */ - select_peripheral(PB(22), PERIPH_B, 0); /* SCLK */ - select_peripheral(PB(23), PERIPH_B, 0); /* SDI */ + pin_mask = (1 << 20) | (1 << 21); /* SDO & SYNC */ + pin_mask |= (1 << 22) | (1 << 23); /* SCLK & SDI */ + + select_peripheral(PIOB, pin_mask, PERIPH_B, 0); /* TODO: gpio_is_valid(data->reset_pin) with kernel 2.6.26. */ if (data->reset_pin != GPIO_PIN_NONE) @@ -2013,6 +2058,7 @@ static struct clk abdac0_sample_clk = { struct platform_device *__init at32_add_device_abdac(unsigned int id) { struct platform_device *pdev; + u32 pin_mask; if (id != 0) return NULL; @@ -2025,10 +2071,10 @@ struct platform_device *__init at32_add_device_abdac(unsigned int id) ARRAY_SIZE(abdac0_resource))) goto err_add_resources; - select_peripheral(PB(20), PERIPH_A, 0); /* DATA1 */ - select_peripheral(PB(21), PERIPH_A, 0); /* DATA0 */ - select_peripheral(PB(22), PERIPH_A, 0); /* DATAN1 */ - select_peripheral(PB(23), PERIPH_A, 0); /* DATAN0 */ + pin_mask = (1 << 20) | (1 << 22); /* DATA1 & DATAN1 */ + pin_mask |= (1 << 21) | (1 << 23); /* DATA0 & DATAN0 */ + + select_peripheral(PIOB, pin_mask, PERIPH_A, 0); abdac0_pclk.dev = &pdev->dev; abdac0_sample_clk.dev = &pdev->dev; @@ -2085,7 +2131,7 @@ static struct clk gclk4 = { .index = 4, }; -struct clk *at32_clock_list[] = { +static __initdata struct clk *init_clocks[] = { &osc32k, &osc0, &osc1, @@ -2097,7 +2143,7 @@ struct clk *at32_clock_list[] = { &pbb_clk, &at32_pm_pclk, &at32_intc0_pclk, - &hmatrix_clk, + &at32_hmatrix_clk, &ebi_clk, &hramc_clk, &sdramc_clk, @@ -2149,7 +2195,6 @@ struct clk *at32_clock_list[] = { &gclk3, &gclk4, }; -unsigned int at32_nr_clocks = ARRAY_SIZE(at32_clock_list); void __init setup_platform(void) { @@ -2180,14 +2225,19 @@ void __init setup_platform(void) genclk_init_parent(&abdac0_sample_clk); /* - * Turn on all clocks that have at least one user already, and - * turn off everything else. We only do this for module - * clocks, and even though it isn't particularly pretty to - * check the address of the mode function, it should do the - * trick... + * Build initial dynamic clock list by registering all clocks + * from the array. + * At the same time, turn on all clocks that have at least one + * user already, and turn off everything else. We only do this + * for module clocks, and even though it isn't particularly + * pretty to check the address of the mode function, it should + * do the trick... */ - for (i = 0; i < ARRAY_SIZE(at32_clock_list); i++) { - struct clk *clk = at32_clock_list[i]; + for (i = 0; i < ARRAY_SIZE(init_clocks); i++) { + struct clk *clk = init_clocks[i]; + + /* first, register clock */ + at32_clk_register(clk); if (clk->users == 0) continue; diff --git a/arch/avr32/mach-at32ap/clock.c b/arch/avr32/mach-at32ap/clock.c index 4642117..138a00a 100644 --- a/arch/avr32/mach-at32ap/clock.c +++ b/arch/avr32/mach-at32ap/clock.c @@ -15,22 +15,40 @@ #include <linux/err.h> #include <linux/device.h> #include <linux/string.h> +#include <linux/list.h> + +#include <mach/chip.h> #include "clock.h" +/* at32 clock list */ +static LIST_HEAD(at32_clock_list); + static DEFINE_SPINLOCK(clk_lock); +static DEFINE_SPINLOCK(clk_list_lock); + +void at32_clk_register(struct clk *clk) +{ + spin_lock(&clk_list_lock); + /* add the new item to the end of the list */ + list_add_tail(&clk->list, &at32_clock_list); + spin_unlock(&clk_list_lock); +} struct clk *clk_get(struct device *dev, const char *id) { - int i; + struct clk *clk; - for (i = 0; i < at32_nr_clocks; i++) { - struct clk *clk = at32_clock_list[i]; + spin_lock(&clk_list_lock); - if (clk->dev == dev && strcmp(id, clk->name) == 0) + list_for_each_entry(clk, &at32_clock_list, list) { + if (clk->dev == dev && strcmp(id, clk->name) == 0) { + spin_unlock(&clk_list_lock); return clk; + } } + spin_unlock(&clk_list_lock); return ERR_PTR(-ENOENT); } EXPORT_SYMBOL(clk_get); @@ -201,8 +219,8 @@ dump_clock(struct clk *parent, struct clkinf *r) /* cost of this scan is small, but not linear... */ r->nest = nest + NEST_DELTA; - for (i = 3; i < at32_nr_clocks; i++) { - clk = at32_clock_list[i]; + + list_for_each_entry(clk, &at32_clock_list, list) { if (clk->parent == parent) dump_clock(clk, r); } @@ -213,6 +231,7 @@ static int clk_show(struct seq_file *s, void *unused) { struct clkinf r; int i; + struct clk *clk; /* show all the power manager registers */ seq_printf(s, "MCCTRL = %8x\n", pm_readl(MCCTRL)); @@ -232,14 +251,25 @@ static int clk_show(struct seq_file *s, void *unused) seq_printf(s, "\n"); - /* show clock tree as derived from the three oscillators - * we "know" are at the head of the list - */ r.s = s; r.nest = 0; - dump_clock(at32_clock_list[0], &r); - dump_clock(at32_clock_list[1], &r); - dump_clock(at32_clock_list[2], &r); + /* protected from changes on the list while dumping */ + spin_lock(&clk_list_lock); + + /* show clock tree as derived from the three oscillators */ + clk = clk_get(NULL, "osc32k"); + dump_clock(clk, &r); + clk_put(clk); + + clk = clk_get(NULL, "osc0"); + dump_clock(clk, &r); + clk_put(clk); + + clk = clk_get(NULL, "osc1"); + dump_clock(clk, &r); + clk_put(clk); + + spin_unlock(&clk_list_lock); return 0; } diff --git a/arch/avr32/mach-at32ap/clock.h b/arch/avr32/mach-at32ap/clock.h index bb8e1f2..623bf0e 100644 --- a/arch/avr32/mach-at32ap/clock.h +++ b/arch/avr32/mach-at32ap/clock.h @@ -12,8 +12,13 @@ * published by the Free Software Foundation. */ #include <linux/clk.h> +#include <linux/list.h> + + +void at32_clk_register(struct clk *clk); struct clk { + struct list_head list; /* linking element */ const char *name; /* Clock name/function */ struct device *dev; /* Device the clock is used by */ struct clk *parent; /* Parent clock, if any */ @@ -25,6 +30,3 @@ struct clk { u16 users; /* Enabled if non-zero */ u16 index; /* Sibling index */ }; - -extern struct clk *at32_clock_list[]; -extern unsigned int at32_nr_clocks; diff --git a/arch/avr32/mach-at32ap/hmatrix.c b/arch/avr32/mach-at32ap/hmatrix.c new file mode 100644 index 0000000..48f5ede --- /dev/null +++ b/arch/avr32/mach-at32ap/hmatrix.c @@ -0,0 +1,88 @@ +/* + * High-Speed Bus Matrix helper functions + * + * Copyright (C) 2008 Atmel Corporation + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#include <linux/clk.h> +#include <linux/io.h> + +#include <mach/chip.h> +#include <mach/hmatrix.h> + +static inline void __hmatrix_write_reg(unsigned long offset, u32 value) +{ + __raw_writel(value, (void __iomem __force *)(HMATRIX_BASE + offset)); +} + +static inline u32 __hmatrix_read_reg(unsigned long offset) +{ + return __raw_readl((void __iomem __force *)(HMATRIX_BASE + offset)); +} + +/** + * hmatrix_write_reg - write HMATRIX configuration register + * @offset: register offset + * @value: value to be written to the register at @offset + */ +void hmatrix_write_reg(unsigned long offset, u32 value) +{ + clk_enable(&at32_hmatrix_clk); + __hmatrix_write_reg(offset, value); + __hmatrix_read_reg(offset); + clk_disable(&at32_hmatrix_clk); +} + +/** + * hmatrix_read_reg - read HMATRIX configuration register + * @offset: register offset + * + * Returns the value of the register at @offset. + */ +u32 hmatrix_read_reg(unsigned long offset) +{ + u32 value; + + clk_enable(&at32_hmatrix_clk); + value = __hmatrix_read_reg(offset); + clk_disable(&at32_hmatrix_clk); + + return value; +} + +/** + * hmatrix_sfr_set_bits - set bits in a slave's Special Function Register + * @slave_id: operate on the SFR belonging to this slave + * @mask: mask of bits to be set in the SFR + */ +void hmatrix_sfr_set_bits(unsigned int slave_id, u32 mask) +{ + u32 value; + + clk_enable(&at32_hmatrix_clk); + value = __hmatrix_read_reg(HMATRIX_SFR(slave_id)); + value |= mask; + __hmatrix_write_reg(HMATRIX_SFR(slave_id), value); + __hmatrix_read_reg(HMATRIX_SFR(slave_id)); + clk_disable(&at32_hmatrix_clk); +} + +/** + * hmatrix_sfr_set_bits - clear bits in a slave's Special Function Register + * @slave_id: operate on the SFR belonging to this slave + * @mask: mask of bits to be cleared in the SFR + */ +void hmatrix_sfr_clear_bits(unsigned int slave_id, u32 mask) +{ + u32 value; + + clk_enable(&at32_hmatrix_clk); + value = __hmatrix_read_reg(HMATRIX_SFR(slave_id)); + value &= ~mask; + __hmatrix_write_reg(HMATRIX_SFR(slave_id), value); + __hmatrix_read_reg(HMATRIX_SFR(slave_id)); + clk_disable(&at32_hmatrix_clk); +} diff --git a/arch/avr32/mach-at32ap/hmatrix.h b/arch/avr32/mach-at32ap/hmatrix.h deleted file mode 100644 index d10bfb6..0000000 --- a/arch/avr32/mach-at32ap/hmatrix.h +++ /dev/null @@ -1,182 +0,0 @@ -/* - * Register definitions for High-Speed Bus Matrix - */ -#ifndef __HMATRIX_H -#define __HMATRIX_H - -/* HMATRIX register offsets */ -#define HMATRIX_MCFG0 0x0000 -#define HMATRIX_MCFG1 0x0004 -#define HMATRIX_MCFG2 0x0008 -#define HMATRIX_MCFG3 0x000c -#define HMATRIX_MCFG4 0x0010 -#define HMATRIX_MCFG5 0x0014 -#define HMATRIX_MCFG6 0x0018 -#define HMATRIX_MCFG7 0x001c -#define HMATRIX_MCFG8 0x0020 -#define HMATRIX_MCFG9 0x0024 -#define HMATRIX_MCFG10 0x0028 -#define HMATRIX_MCFG11 0x002c -#define HMATRIX_MCFG12 0x0030 -#define HMATRIX_MCFG13 0x0034 -#define HMATRIX_MCFG14 0x0038 -#define HMATRIX_MCFG15 0x003c -#define HMATRIX_SCFG0 0x0040 -#define HMATRIX_SCFG1 0x0044 -#define HMATRIX_SCFG2 0x0048 -#define HMATRIX_SCFG3 0x004c -#define HMATRIX_SCFG4 0x0050 -#define HMATRIX_SCFG5 0x0054 -#define HMATRIX_SCFG6 0x0058 -#define HMATRIX_SCFG7 0x005c -#define HMATRIX_SCFG8 0x0060 -#define HMATRIX_SCFG9 0x0064 -#define HMATRIX_SCFG10 0x0068 -#define HMATRIX_SCFG11 0x006c -#define HMATRIX_SCFG12 0x0070 -#define HMATRIX_SCFG13 0x0074 -#define HMATRIX_SCFG14 0x0078 -#define HMATRIX_SCFG15 0x007c -#define HMATRIX_PRAS0 0x0080 -#define HMATRIX_PRBS0 0x0084 -#define HMATRIX_PRAS1 0x0088 -#define HMATRIX_PRBS1 0x008c -#define HMATRIX_PRAS2 0x0090 -#define HMATRIX_PRBS2 0x0094 -#define HMATRIX_PRAS3 0x0098 -#define HMATRIX_PRBS3 0x009c -#define HMATRIX_PRAS4 0x00a0 -#define HMATRIX_PRBS4 0x00a4 -#define HMATRIX_PRAS5 0x00a8 -#define HMATRIX_PRBS5 0x00ac -#define HMATRIX_PRAS6 0x00b0 -#define HMATRIX_PRBS6 0x00b4 -#define HMATRIX_PRAS7 0x00b8 -#define HMATRIX_PRBS7 0x00bc -#define HMATRIX_PRAS8 0x00c0 -#define HMATRIX_PRBS8 0x00c4 -#define HMATRIX_PRAS9 0x00c8 -#define HMATRIX_PRBS9 0x00cc -#define HMATRIX_PRAS10 0x00d0 -#define HMATRIX_PRBS10 0x00d4 -#define HMATRIX_PRAS11 0x00d8 -#define HMATRIX_PRBS11 0x00dc -#define HMATRIX_PRAS12 0x00e0 -#define HMATRIX_PRBS12 0x00e4 -#define HMATRIX_PRAS13 0x00e8 -#define HMATRIX_PRBS13 0x00ec -#define HMATRIX_PRAS14 0x00f0 -#define HMATRIX_PRBS14 0x00f4 -#define HMATRIX_PRAS15 0x00f8 -#define HMATRIX_PRBS15 0x00fc -#define HMATRIX_MRCR 0x0100 -#define HMATRIX_SFR0 0x0110 -#define HMATRIX_SFR1 0x0114 -#define HMATRIX_SFR2 0x0118 -#define HMATRIX_SFR3 0x011c -#define HMATRIX_SFR4 0x0120 -#define HMATRIX_SFR5 0x0124 -#define HMATRIX_SFR6 0x0128 -#define HMATRIX_SFR7 0x012c -#define HMATRIX_SFR8 0x0130 -#define HMATRIX_SFR9 0x0134 -#define HMATRIX_SFR10 0x0138 -#define HMATRIX_SFR11 0x013c -#define HMATRIX_SFR12 0x0140 -#define HMATRIX_SFR13 0x0144 -#define HMATRIX_SFR14 0x0148 -#define HMATRIX_SFR15 0x014c - -/* Bitfields in MCFGx */ -#define HMATRIX_ULBT_OFFSET 0 -#define HMATRIX_ULBT_SIZE 3 - -/* Bitfields in SCFGx */ -#define HMATRIX_SLOT_CYCLE_OFFSET 0 -#define HMATRIX_SLOT_CYCLE_SIZE 8 -#define HMATRIX_DEFMSTR_TYPE_OFFSET 16 -#define HMATRIX_DEFMSTR_TYPE_SIZE 2 -#define HMATRIX_FIXED_DEFMSTR_OFFSET 18 -#define HMATRIX_FIXED_DEFMSTR_SIZE 4 -#define HMATRIX_ARBT_OFFSET 24 -#define HMATRIX_ARBT_SIZE 2 - -/* Bitfields in PRASx */ -#define HMATRIX_M0PR_OFFSET 0 -#define HMATRIX_M0PR_SIZE 4 -#define HMATRIX_M1PR_OFFSET 4 -#define HMATRIX_M1PR_SIZE 4 -#define HMATRIX_M2PR_OFFSET 8 -#define HMATRIX_M2PR_SIZE 4 -#define HMATRIX_M3PR_OFFSET 12 -#define HMATRIX_M3PR_SIZE 4 -#define HMATRIX_M4PR_OFFSET 16 -#define HMATRIX_M4PR_SIZE 4 -#define HMATRIX_M5PR_OFFSET 20 -#define HMATRIX_M5PR_SIZE 4 -#define HMATRIX_M6PR_OFFSET 24 -#define HMATRIX_M6PR_SIZE 4 -#define HMATRIX_M7PR_OFFSET 28 -#define HMATRIX_M7PR_SIZE 4 - -/* Bitfields in PRBSx */ -#define HMATRIX_M8PR_OFFSET 0 -#define HMATRIX_M8PR_SIZE 4 -#define HMATRIX_M9PR_OFFSET 4 -#define HMATRIX_M9PR_SIZE 4 -#define HMATRIX_M10PR_OFFSET 8 -#define HMATRIX_M10PR_SIZE 4 -#define HMATRIX_M11PR_OFFSET 12 -#define HMATRIX_M11PR_SIZE 4 -#define HMATRIX_M12PR_OFFSET 16 -#define HMATRIX_M12PR_SIZE 4 -#define HMATRIX_M13PR_OFFSET 20 -#define HMATRIX_M13PR_SIZE 4 -#define HMATRIX_M14PR_OFFSET 24 -#define HMATRIX_M14PR_SIZE 4 -#define HMATRIX_M15PR_OFFSET 28 -#define HMATRIX_M15PR_SIZE 4 - -/* Bitfields in SFR4 */ -#define HMATRIX_CS1A_OFFSET 1 -#define HMATRIX_CS1A_SIZE 1 -#define HMATRIX_CS3A_OFFSET 3 -#define HMATRIX_CS3A_SIZE 1 -#define HMATRIX_CS4A_OFFSET 4 -#define HMATRIX_CS4A_SIZE 1 -#define HMATRIX_CS5A_OFFSET 5 -#define HMATRIX_CS5A_SIZE 1 -#define HMATRIX_DBPUC_OFFSET 8 -#define HMATRIX_DBPUC_SIZE 1 - -/* Constants for ULBT */ -#define HMATRIX_ULBT_INFINITE 0 -#define HMATRIX_ULBT_SINGLE 1 -#define HMATRIX_ULBT_FOUR_BEAT 2 -#define HMATRIX_ULBT_EIGHT_BEAT 3 -#define HMATRIX_ULBT_SIXTEEN_BEAT 4 - -/* Constants for DEFMSTR_TYPE */ -#define HMATRIX_DEFMSTR_TYPE_NO_DEFAULT 0 -#define HMATRIX_DEFMSTR_TYPE_LAST_DEFAULT 1 -#define HMATRIX_DEFMSTR_TYPE_FIXED_DEFAULT 2 - -/* Constants for ARBT */ -#define HMATRIX_ARBT_ROUND_ROBIN 0 -#define HMATRIX_ARBT_FIXED_PRIORITY 1 - -/* Bit manipulation macros */ -#define HMATRIX_BIT(name) \ - (1 << HMATRIX_##name##_OFFSET) -#define HMATRIX_BF(name,value) \ - (((value) & ((1 << HMATRIX_##name##_SIZE) - 1)) \ - << HMATRIX_##name##_OFFSET) -#define HMATRIX_BFEXT(name,value) \ - (((value) >> HMATRIX_##name##_OFFSET) \ - & ((1 << HMATRIX_##name##_SIZE) - 1)) -#define HMATRIX_BFINS(name,value,old) \ - (((old) & ~(((1 << HMATRIX_##name##_SIZE) - 1) \ - << HMATRIX_##name##_OFFSET)) \ - | HMATRIX_BF(name,value)) - -#endif /* __HMATRIX_H */ diff --git a/arch/avr32/mach-at32ap/include/mach/at32ap700x.h b/arch/avr32/mach-at32ap/include/mach/at32ap700x.h index d18a305..a77d372 100644 --- a/arch/avr32/mach-at32ap/include/mach/at32ap700x.h +++ b/arch/avr32/mach-at32ap/include/mach/at32ap700x.h @@ -46,4 +46,169 @@ #define DMAC_DMAREQ_2 9 #define DMAC_DMAREQ_3 10 +/* HSB master IDs */ +#define HMATRIX_MASTER_CPU_DCACHE 0 +#define HMATRIX_MASTER_CPU_ICACHE 1 +#define HMATRIX_MASTER_PDC 2 +#define HMATRIX_MASTER_ISI 3 +#define HMATRIX_MASTER_USBA 4 +#define HMATRIX_MASTER_LCDC 5 +#define HMATRIX_MASTER_MACB0 6 +#define HMATRIX_MASTER_MACB1 7 +#define HMATRIX_MASTER_DMACA_M0 8 +#define HMATRIX_MASTER_DMACA_M1 9 + +/* HSB slave IDs */ +#define HMATRIX_SLAVE_SRAM0 0 +#define HMATRIX_SLAVE_SRAM1 1 +#define HMATRIX_SLAVE_PBA 2 +#define HMATRIX_SLAVE_PBB 3 +#define HMATRIX_SLAVE_EBI 4 +#define HMATRIX_SLAVE_USBA 5 +#define HMATRIX_SLAVE_LCDC 6 +#define HMATRIX_SLAVE_DMACA 7 + +/* Bits in HMATRIX SFR4 (EBI) */ +#define HMATRIX_EBI_SDRAM_ENABLE (1 << 1) +#define HMATRIX_EBI_NAND_ENABLE (1 << 3) +#define HMATRIX_EBI_CF0_ENABLE (1 << 4) +#define HMATRIX_EBI_CF1_ENABLE (1 << 5) +#define HMATRIX_EBI_PULLUP_DISABLE (1 << 8) + +/* + * Base addresses of controllers that may be accessed early by + * platform code. + */ +#define PM_BASE 0xfff00000 +#define HMATRIX_BASE 0xfff00800 +#define SDRAMC_BASE 0xfff03800 + +/* LCDC on port C */ +#define ATMEL_LCDC_PC_CC (1ULL << 19) +#define ATMEL_LCDC_PC_HSYNC (1ULL << 20) +#define ATMEL_LCDC_PC_PCLK (1ULL << 21) +#define ATMEL_LCDC_PC_VSYNC (1ULL << 22) +#define ATMEL_LCDC_PC_DVAL (1ULL << 23) +#define ATMEL_LCDC_PC_MODE (1ULL << 24) +#define ATMEL_LCDC_PC_PWR (1ULL << 25) +#define ATMEL_LCDC_PC_DATA0 (1ULL << 26) +#define ATMEL_LCDC_PC_DATA1 (1ULL << 27) +#define ATMEL_LCDC_PC_DATA2 (1ULL << 28) +#define ATMEL_LCDC_PC_DATA3 (1ULL << 29) +#define ATMEL_LCDC_PC_DATA4 (1ULL << 30) +#define ATMEL_LCDC_PC_DATA5 (1ULL << 31) + +/* LCDC on port D */ +#define ATMEL_LCDC_PD_DATA6 (1ULL << 0) +#define ATMEL_LCDC_PD_DATA7 (1ULL << 1) +#define ATMEL_LCDC_PD_DATA8 (1ULL << 2) +#define ATMEL_LCDC_PD_DATA9 (1ULL << 3) +#define ATMEL_LCDC_PD_DATA10 (1ULL << 4) +#define ATMEL_LCDC_PD_DATA11 (1ULL << 5) +#define ATMEL_LCDC_PD_DATA12 (1ULL << 6) +#define ATMEL_LCDC_PD_DATA13 (1ULL << 7) +#define ATMEL_LCDC_PD_DATA14 (1ULL << 8) +#define ATMEL_LCDC_PD_DATA15 (1ULL << 9) +#define ATMEL_LCDC_PD_DATA16 (1ULL << 10) +#define ATMEL_LCDC_PD_DATA17 (1ULL << 11) +#define ATMEL_LCDC_PD_DATA18 (1ULL << 12) +#define ATMEL_LCDC_PD_DATA19 (1ULL << 13) +#define ATMEL_LCDC_PD_DATA20 (1ULL << 14) +#define ATMEL_LCDC_PD_DATA21 (1ULL << 15) +#define ATMEL_LCDC_PD_DATA22 (1ULL << 16) +#define ATMEL_LCDC_PD_DATA23 (1ULL << 17) + +/* LCDC on port E */ +#define ATMEL_LCDC_PE_CC (1ULL << (32 + 0)) +#define ATMEL_LCDC_PE_DVAL (1ULL << (32 + 1)) +#define ATMEL_LCDC_PE_MODE (1ULL << (32 + 2)) +#define ATMEL_LCDC_PE_DATA0 (1ULL << (32 + 3)) +#define ATMEL_LCDC_PE_DATA1 (1ULL << (32 + 4)) +#define ATMEL_LCDC_PE_DATA2 (1ULL << (32 + 5)) +#define ATMEL_LCDC_PE_DATA3 (1ULL << (32 + 6)) +#define ATMEL_LCDC_PE_DATA4 (1ULL << (32 + 7)) +#define ATMEL_LCDC_PE_DATA8 (1ULL << (32 + 8)) +#define ATMEL_LCDC_PE_DATA9 (1ULL << (32 + 9)) +#define ATMEL_LCDC_PE_DATA10 (1ULL << (32 + 10)) +#define ATMEL_LCDC_PE_DATA11 (1ULL << (32 + 11)) +#define ATMEL_LCDC_PE_DATA12 (1ULL << (32 + 12)) +#define ATMEL_LCDC_PE_DATA16 (1ULL << (32 + 13)) +#define ATMEL_LCDC_PE_DATA17 (1ULL << (32 + 14)) +#define ATMEL_LCDC_PE_DATA18 (1ULL << (32 + 15)) +#define ATMEL_LCDC_PE_DATA19 (1ULL << (32 + 16)) +#define ATMEL_LCDC_PE_DATA20 (1ULL << (32 + 17)) +#define ATMEL_LCDC_PE_DATA21 (1ULL << (32 + 18)) + + +#define ATMEL_LCDC(PORT, PIN) (ATMEL_LCDC_##PORT##_##PIN) + + +#define ATMEL_LCDC_PRI_24B_DATA ( \ + ATMEL_LCDC(PC, DATA0) | ATMEL_LCDC(PC, DATA1) | \ + ATMEL_LCDC(PC, DATA2) | ATMEL_LCDC(PC, DATA3) | \ + ATMEL_LCDC(PC, DATA4) | ATMEL_LCDC(PC, DATA5) | \ + ATMEL_LCDC(PD, DATA6) | ATMEL_LCDC(PD, DATA7) | \ + ATMEL_LCDC(PD, DATA8) | ATMEL_LCDC(PD, DATA9) | \ + ATMEL_LCDC(PD, DATA10) | ATMEL_LCDC(PD, DATA11) | \ + ATMEL_LCDC(PD, DATA12) | ATMEL_LCDC(PD, DATA13) | \ + ATMEL_LCDC(PD, DATA14) | ATMEL_LCDC(PD, DATA15) | \ + ATMEL_LCDC(PD, DATA16) | ATMEL_LCDC(PD, DATA17) | \ + ATMEL_LCDC(PD, DATA18) | ATMEL_LCDC(PD, DATA19) | \ + ATMEL_LCDC(PD, DATA20) | ATMEL_LCDC(PD, DATA21) | \ + ATMEL_LCDC(PD, DATA22) | ATMEL_LCDC(PD, DATA23)) + +#define ATMEL_LCDC_ALT_24B_DATA ( \ + ATMEL_LCDC(PE, DATA0) | ATMEL_LCDC(PE, DATA1) | \ + ATMEL_LCDC(PE, DATA2) | ATMEL_LCDC(PE, DATA3) | \ + ATMEL_LCDC(PE, DATA4) | ATMEL_LCDC(PC, DATA5) | \ + ATMEL_LCDC(PD, DATA6) | ATMEL_LCDC(PD, DATA7) | \ + ATMEL_LCDC(PE, DATA8) | ATMEL_LCDC(PE, DATA9) | \ + ATMEL_LCDC(PE, DATA10) | ATMEL_LCDC(PE, DATA11) | \ + ATMEL_LCDC(PE, DATA12) | ATMEL_LCDC(PD, DATA13) | \ + ATMEL_LCDC(PD, DATA14) | ATMEL_LCDC(PD, DATA15) | \ + ATMEL_LCDC(PE, DATA16) | ATMEL_LCDC(PE, DATA17) | \ + ATMEL_LCDC(PE, DATA18) | ATMEL_LCDC(PE, DATA19) | \ + ATMEL_LCDC(PE, DATA20) | ATMEL_LCDC(PE, DATA21) | \ + ATMEL_LCDC(PD, DATA22) | ATMEL_LCDC(PD, DATA23)) + +#define ATMEL_LCDC_PRI_15B_DATA ( \ + ATMEL_LCDC(PC, DATA0) | ATMEL_LCDC(PC, DATA1) | \ + ATMEL_LCDC(PC, DATA2) | ATMEL_LCDC(PC, DATA3) | \ + ATMEL_LCDC(PC, DATA4) | ATMEL_LCDC(PC, DATA5) | \ + ATMEL_LCDC(PD, DATA8) | ATMEL_LCDC(PD, DATA9) | \ + ATMEL_LCDC(PD, DATA10) | ATMEL_LCDC(PD, DATA11) | \ + ATMEL_LCDC(PD, DATA12) | ATMEL_LCDC(PD, DATA16) | \ + ATMEL_LCDC(PD, DATA17) | ATMEL_LCDC(PD, DATA18) | \ + ATMEL_LCDC(PD, DATA19) | ATMEL_LCDC(PD, DATA20)) + +#define ATMEL_LCDC_ALT_15B_DATA ( \ + ATMEL_LCDC(PE, DATA0) | ATMEL_LCDC(PE, DATA1) | \ + ATMEL_LCDC(PE, DATA2) | ATMEL_LCDC(PE, DATA3) | \ + ATMEL_LCDC(PE, DATA4) | ATMEL_LCDC(PC, DATA5) | \ + ATMEL_LCDC(PE, DATA8) | ATMEL_LCDC(PE, DATA9) | \ + ATMEL_LCDC(PE, DATA10) | ATMEL_LCDC(PE, DATA11) | \ + ATMEL_LCDC(PE, DATA12) | ATMEL_LCDC(PE, DATA16) | \ + ATMEL_LCDC(PE, DATA17) | ATMEL_LCDC(PE, DATA18) | \ + ATMEL_LCDC(PE, DATA19) | ATMEL_LCDC(PE, DATA20)) + +#define ATMEL_LCDC_PRI_CONTROL ( \ + ATMEL_LCDC(PC, CC) | ATMEL_LCDC(PC, DVAL) | \ + ATMEL_LCDC(PC, MODE) | ATMEL_LCDC(PC, PWR)) + +#define ATMEL_LCDC_ALT_CONTROL ( \ + ATMEL_LCDC(PE, CC) | ATMEL_LCDC(PE, DVAL) | \ + ATMEL_LCDC(PE, MODE) | ATMEL_LCDC(PC, PWR)) + +#define ATMEL_LCDC_CONTROL ( \ + ATMEL_LCDC(PC, HSYNC) | ATMEL_LCDC(PC, VSYNC) | \ + ATMEL_LCDC(PC, PCLK)) + +#define ATMEL_LCDC_PRI_24BIT (ATMEL_LCDC_CONTROL | ATMEL_LCDC_PRI_24B_DATA) + +#define ATMEL_LCDC_ALT_24BIT (ATMEL_LCDC_CONTROL | ATMEL_LCDC_ALT_24B_DATA) + +#define ATMEL_LCDC_PRI_15BIT (ATMEL_LCDC_CONTROL | ATMEL_LCDC_PRI_15B_DATA) + +#define ATMEL_LCDC_ALT_15BIT (ATMEL_LCDC_CONTROL | ATMEL_LCDC_ALT_15B_DATA) + #endif /* __ASM_ARCH_AT32AP700X_H__ */ diff --git a/arch/avr32/mach-at32ap/include/mach/board.h b/arch/avr32/mach-at32ap/include/mach/board.h index e60e907..c48386d 100644 --- a/arch/avr32/mach-at32ap/include/mach/board.h +++ b/arch/avr32/mach-at32ap/include/mach/board.h @@ -43,7 +43,7 @@ struct atmel_lcdfb_info; struct platform_device * at32_add_device_lcdc(unsigned int id, struct atmel_lcdfb_info *data, unsigned long fbmem_start, unsigned long fbmem_len, - unsigned int pin_config); + u64 pin_mask); struct usba_platform_data; struct platform_device * diff --git a/arch/avr32/mach-at32ap/include/mach/chip.h b/arch/avr32/mach-at32ap/include/mach/chip.h new file mode 100644 index 0000000..5efca6d --- /dev/null +++ b/arch/avr32/mach-at32ap/include/mach/chip.h @@ -0,0 +1,19 @@ +/* + * AVR32 chip-specific definitions + * + * Copyright (C) 2008 Atmel Corporation + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#ifndef __ASM_AVR32_ARCH_CHIP_H__ +#define __ASM_AVR32_ARCH_CHIP_H__ + +#if defined(CONFIG_CPU_AT32AP700X) +# include <mach/at32ap700x.h> +#else +# error Unknown chip type selected +#endif + +#endif /* __ASM_AVR32_ARCH_CHIP_H__ */ diff --git a/arch/avr32/mach-at32ap/include/mach/hmatrix.h b/arch/avr32/mach-at32ap/include/mach/hmatrix.h new file mode 100644 index 0000000..7a368f2 --- /dev/null +++ b/arch/avr32/mach-at32ap/include/mach/hmatrix.h @@ -0,0 +1,55 @@ +/* + * High-Speed Bus Matrix configuration registers + * + * Copyright (C) 2008 Atmel Corporation + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#ifndef __HMATRIX_H +#define __HMATRIX_H + +extern struct clk at32_hmatrix_clk; + +void hmatrix_write_reg(unsigned long offset, u32 value); +u32 hmatrix_read_reg(unsigned long offset); + +void hmatrix_sfr_set_bits(unsigned int slave_id, u32 mask); +void hmatrix_sfr_clear_bits(unsigned int slave_id, u32 mask); + +/* Master Configuration register */ +#define HMATRIX_MCFG(m) (0x0000 + 4 * (m)) +/* Undefined length burst limit */ +# define HMATRIX_MCFG_ULBT_INFINITE 0 /* Infinite length */ +# define HMATRIX_MCFG_ULBT_SINGLE 1 /* Single Access */ +# define HMATRIX_MCFG_ULBT_FOUR_BEAT 2 /* Four beat */ +# define HMATRIX_MCFG_ULBT_EIGHT_BEAT 3 /* Eight beat */ +# define HMATRIX_MCFG_ULBT_SIXTEEN_BEAT 4 /* Sixteen beat */ + +/* Slave Configuration register */ +#define HMATRIX_SCFG(s) (0x0040 + 4 * (s)) +# define HMATRIX_SCFG_SLOT_CYCLE(x) ((x) << 0) /* Max burst cycles */ +# define HMATRIX_SCFG_DEFMSTR_NONE ( 0 << 16) /* No default master */ +# define HMATRIX_SCFG_DEFMSTR_LAST ( 1 << 16) /* Last def master */ +# define HMATRIX_SCFG_DEFMSTR_FIXED ( 2 << 16) /* Fixed def master */ +# define HMATRIX_SCFG_FIXED_DEFMSTR(m) ((m) << 18) /* Fixed master ID */ +# define HMATRIX_SCFG_ARBT_ROUND_ROBIN ( 0 << 24) /* RR arbitration */ +# define HMATRIX_SCFG_ARBT_FIXED_PRIO ( 1 << 24) /* Fixed priority */ + +/* Slave Priority register A (master 0..7) */ +#define HMATRIX_PRAS(s) (0x0080 + 8 * (s)) +# define HMATRIX_PRAS_PRIO(m, p) ((p) << ((m) * 4)) + +/* Slave Priority register A (master 8..15) */ +#define HMATRIX_PRBS(s) (0x0084 + 8 * (s)) +# define HMATRIX_PRBS_PRIO(m, p) ((p) << (((m) - 8) * 4)) + +/* Master Remap Control Register */ +#define HMATRIX_MRCR 0x0100 +# define HMATRIX_MRCR_REMAP(m) ( 1 << (m)) /* Remap master m */ + +/* Special Function Register. Bit definitions are chip-specific */ +#define HMATRIX_SFR(s) (0x0110 + 4 * (s)) + +#endif /* __HMATRIX_H */ diff --git a/arch/avr32/mach-at32ap/include/mach/io.h b/arch/avr32/mach-at32ap/include/mach/io.h index 4ec6abc..22ea79b 100644 --- a/arch/avr32/mach-at32ap/include/mach/io.h +++ b/arch/avr32/mach-at32ap/include/mach/io.h @@ -1,8 +1,7 @@ #ifndef __ASM_AVR32_ARCH_AT32AP_IO_H #define __ASM_AVR32_ARCH_AT32AP_IO_H -/* For "bizarre" halfword swapping */ -#include <linux/byteorder/swabb.h> +#include <linux/swab.h> #if defined(CONFIG_AP700X_32_BIT_SMC) # define __swizzle_addr_b(addr) (addr ^ 3UL) diff --git a/arch/avr32/mach-at32ap/include/mach/portmux.h b/arch/avr32/mach-at32ap/include/mach/portmux.h index b1abe6b..21c7937 100644 --- a/arch/avr32/mach-at32ap/include/mach/portmux.h +++ b/arch/avr32/mach-at32ap/include/mach/portmux.h @@ -21,9 +21,10 @@ #define AT32_GPIOF_DEGLITCH 0x00000008 /* (IN) Filter glitches */ #define AT32_GPIOF_MULTIDRV 0x00000010 /* Enable multidriver option */ -void at32_select_periph(unsigned int pin, unsigned int periph, - unsigned long flags); +void at32_select_periph(unsigned int port, unsigned int pin, + unsigned int periph, unsigned long flags); void at32_select_gpio(unsigned int pin, unsigned long flags); +void at32_deselect_pin(unsigned int pin); void at32_reserve_pin(unsigned int pin); #endif /* __ASM_ARCH_PORTMUX_H__ */ diff --git a/arch/avr32/mach-at32ap/pdc.c b/arch/avr32/mach-at32ap/pdc.c index 1040bda..61ab15a 100644 --- a/arch/avr32/mach-at32ap/pdc.c +++ b/arch/avr32/mach-at32ap/pdc.c @@ -35,7 +35,6 @@ static int __init pdc_probe(struct platform_device *pdev) } static struct platform_driver pdc_driver = { - .probe = pdc_probe, .driver = { .name = "pdc", }, @@ -43,6 +42,6 @@ static struct platform_driver pdc_driver = { static int __init pdc_init(void) { - return platform_driver_register(&pdc_driver); + return platform_driver_probe(&pdc_driver, pdc_probe); } arch_initcall(pdc_init); diff --git a/arch/avr32/mach-at32ap/pio.c b/arch/avr32/mach-at32ap/pio.c index 405ee6b..ed81a8b 100644 --- a/arch/avr32/mach-at32ap/pio.c +++ b/arch/avr32/mach-at32ap/pio.c @@ -50,35 +50,48 @@ static struct pio_device *gpio_to_pio(unsigned int gpio) } /* Pin multiplexing API */ +static DEFINE_SPINLOCK(pio_lock); -void __init at32_select_periph(unsigned int pin, unsigned int periph, - unsigned long flags) +void __init at32_select_periph(unsigned int port, u32 pin_mask, + unsigned int periph, unsigned long flags) { struct pio_device *pio; - unsigned int pin_index = pin & 0x1f; - u32 mask = 1 << pin_index; - pio = gpio_to_pio(pin); + /* assign and verify pio */ + pio = gpio_to_pio(port); if (unlikely(!pio)) { - printk("pio: invalid pin %u\n", pin); + printk(KERN_WARNING "pio: invalid port %u\n", port); goto fail; } - if (unlikely(test_and_set_bit(pin_index, &pio->pinmux_mask) - || gpiochip_is_requested(&pio->chip, pin_index))) { - printk("%s: pin %u is busy\n", pio->name, pin_index); + /* Test if any of the requested pins is already muxed */ + spin_lock(&pio_lock); + if (unlikely(pio->pinmux_mask & pin_mask)) { + printk(KERN_WARNING "%s: pin(s) busy (requested 0x%x, busy 0x%x)\n", + pio->name, pin_mask, pio->pinmux_mask & pin_mask); + spin_unlock(&pio_lock); goto fail; } - pio_writel(pio, PUER, mask); + pio->pinmux_mask |= pin_mask; + + /* enable pull ups */ + pio_writel(pio, PUER, pin_mask); + + /* select either peripheral A or B */ if (periph) - pio_writel(pio, BSR, mask); + pio_writel(pio, BSR, pin_mask); else - pio_writel(pio, ASR, mask); + pio_writel(pio, ASR, pin_mask); + + /* enable peripheral control */ + pio_writel(pio, PDR, pin_mask); - pio_writel(pio, PDR, mask); + /* Disable pull ups if not requested. */ if (!(flags & AT32_GPIOF_PULLUP)) - pio_writel(pio, PUDR, mask); + pio_writel(pio, PUDR, pin_mask); + + spin_unlock(&pio_lock); return; @@ -134,6 +147,25 @@ fail: dump_stack(); } +/* + * Undo a previous pin reservation. Will not affect the hardware + * configuration. + */ +void at32_deselect_pin(unsigned int pin) +{ + struct pio_device *pio; + unsigned int pin_index = pin & 0x1f; + + pio = gpio_to_pio(pin); + if (unlikely(!pio)) { + printk("pio: invalid pin %u\n", pin); + dump_stack(); + return; + } + + clear_bit(pin_index, &pio->pinmux_mask); +} + /* Reserve a pin, preventing anyone else from changing its configuration. */ void __init at32_reserve_pin(unsigned int pin) { @@ -382,7 +414,6 @@ static int __init pio_probe(struct platform_device *pdev) } static struct platform_driver pio_driver = { - .probe = pio_probe, .driver = { .name = "pio", }, @@ -390,7 +421,7 @@ static struct platform_driver pio_driver = { static int __init pio_init(void) { - return platform_driver_register(&pio_driver); + return platform_driver_probe(&pio_driver, pio_probe); } postcore_initcall(pio_init); diff --git a/arch/avr32/mach-at32ap/pm-at32ap700x.S b/arch/avr32/mach-at32ap/pm-at32ap700x.S index 5be4de6..17503b0 100644 --- a/arch/avr32/mach-at32ap/pm-at32ap700x.S +++ b/arch/avr32/mach-at32ap/pm-at32ap700x.S @@ -134,7 +134,7 @@ pm_standby: mov r11, SDRAMC_LPR_LPCB_SELF_RFR bfins r10, r11, 0, 2 /* LPCB <- self Refresh */ sync 0 /* flush write buffer */ - st.w r12[SDRAMC_LPR], r11 /* put SDRAM in self-refresh mode */ + st.w r12[SDRAMC_LPR], r10 /* put SDRAM in self-refresh mode */ ld.w r11, r12[SDRAMC_LPR] unmask_interrupts sleep CPU_SLEEP_FROZEN diff --git a/arch/avr32/mach-at32ap/pm.c b/arch/avr32/mach-at32ap/pm.c index a0cbef5..f021edf 100644 --- a/arch/avr32/mach-at32ap/pm.c +++ b/arch/avr32/mach-at32ap/pm.c @@ -14,12 +14,10 @@ #include <asm/cacheflush.h> #include <asm/sysreg.h> +#include <mach/chip.h> #include <mach/pm.h> #include <mach/sram.h> -/* FIXME: This is only valid for AP7000 */ -#define SDRAMC_BASE 0xfff03800 - #include "sdramc.h" #define SRAM_PAGE_FLAGS (SYSREG_BIT(TLBELO_D) | SYSREG_BF(SZ, 1) \ diff --git a/arch/avr32/mach-at32ap/pm.h b/arch/avr32/mach-at32ap/pm.h index 694d521..532a373 100644 --- a/arch/avr32/mach-at32ap/pm.h +++ b/arch/avr32/mach-at32ap/pm.h @@ -4,14 +4,6 @@ #ifndef __ARCH_AVR32_MACH_AT32AP_PM_H__ #define __ARCH_AVR32_MACH_AT32AP_PM_H__ -/* - * We can reduce the code size a bit by using a constant here. Since - * this file is only used on AVR32 AP CPUs with segmentation enabled, - * it's safe to not use ioremap. Generic drivers should of course - * never do this. - */ -#define AT32_PM_BASE 0xfff00000 - /* PM register offsets */ #define PM_MCCTRL 0x0000 #define PM_CKSEL 0x0004 @@ -113,8 +105,8 @@ /* Register access macros */ #define pm_readl(reg) \ - __raw_readl((void __iomem __force *)AT32_PM_BASE + PM_##reg) + __raw_readl((void __iomem __force *)PM_BASE + PM_##reg) #define pm_writel(reg,value) \ - __raw_writel((value), (void __iomem __force *)AT32_PM_BASE + PM_##reg) + __raw_writel((value), (void __iomem __force *)PM_BASE + PM_##reg) #endif /* __ARCH_AVR32_MACH_AT32AP_PM_H__ */ diff --git a/arch/avr32/oprofile/Makefile b/arch/avr32/oprofile/Makefile index 1fe81c3..e0eb520 100644 --- a/arch/avr32/oprofile/Makefile +++ b/arch/avr32/oprofile/Makefile @@ -5,4 +5,4 @@ oprofile-y := $(addprefix ../../../drivers/oprofile/, \ event_buffer.o oprofile_files.o \ oprofilefs.o oprofile_stats.o \ timer_int.o) -oprofile-y += op_model_avr32.o +oprofile-y += op_model_avr32.o backtrace.o diff --git a/arch/avr32/oprofile/backtrace.c b/arch/avr32/oprofile/backtrace.c new file mode 100644 index 0000000..75d9ad6 --- /dev/null +++ b/arch/avr32/oprofile/backtrace.c @@ -0,0 +1,81 @@ +/* + * AVR32 specific backtracing code for oprofile + * + * Copyright 2008 Weinmann GmbH + * + * Author: Nikolaus Voss <n.voss@weinmann.de> + * + * Based on i386 oprofile backtrace code by John Levon and David Smith + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#include <linux/oprofile.h> +#include <linux/sched.h> +#include <linux/uaccess.h> + +/* The first two words of each frame on the stack look like this if we have + * frame pointers */ +struct frame_head { + unsigned long lr; + struct frame_head *fp; +}; + +/* copied from arch/avr32/kernel/process.c */ +static inline int valid_stack_ptr(struct thread_info *tinfo, unsigned long p) +{ + return (p > (unsigned long)tinfo) + && (p < (unsigned long)tinfo + THREAD_SIZE - 3); +} + +/* copied from arch/x86/oprofile/backtrace.c */ +static struct frame_head *dump_user_backtrace(struct frame_head *head) +{ + struct frame_head bufhead[2]; + + /* Also check accessibility of one struct frame_head beyond */ + if (!access_ok(VERIFY_READ, head, sizeof(bufhead))) + return NULL; + if (__copy_from_user_inatomic(bufhead, head, sizeof(bufhead))) + return NULL; + + oprofile_add_trace(bufhead[0].lr); + + /* frame pointers should strictly progress back up the stack + * (towards higher addresses) */ + if (bufhead[0].fp <= head) + return NULL; + + return bufhead[0].fp; +} + +void avr32_backtrace(struct pt_regs * const regs, unsigned int depth) +{ + /* Get first frame pointer */ + struct frame_head *head = (struct frame_head *)(regs->r7); + + if (!user_mode(regs)) { +#ifdef CONFIG_FRAME_POINTER + /* + * Traverse the kernel stack from frame to frame up to + * "depth" steps. + */ + while (depth-- && valid_stack_ptr(task_thread_info(current), + (unsigned long)head)) { + oprofile_add_trace(head->lr); + if (head->fp <= head) + break; + head = head->fp; + } +#endif + } else { + /* Assume we have frame pointers in user mode process */ + while (depth-- && head) + head = dump_user_backtrace(head); + } +} + + diff --git a/arch/avr32/oprofile/op_model_avr32.c b/arch/avr32/oprofile/op_model_avr32.c index df42325..a3e9b3c 100644 --- a/arch/avr32/oprofile/op_model_avr32.c +++ b/arch/avr32/oprofile/op_model_avr32.c @@ -22,6 +22,8 @@ #define AVR32_PERFCTR_IRQ_GROUP 0 #define AVR32_PERFCTR_IRQ_LINE 1 +void avr32_backtrace(struct pt_regs * const regs, unsigned int depth); + enum { PCCNT, PCNT0, PCNT1, NR_counter }; struct avr32_perf_counter { @@ -223,6 +225,8 @@ int __init oprofile_arch_init(struct oprofile_operations *ops) memcpy(ops, &avr32_perf_counter_ops, sizeof(struct oprofile_operations)); + ops->backtrace = avr32_backtrace; + printk(KERN_INFO "oprofile: using AVR32 performance monitoring.\n"); return 0; |
