diff options
Diffstat (limited to 'arch/arm')
83 files changed, 1077 insertions, 376 deletions
diff --git a/arch/arm/boot/dts/am335x-base0033.dts b/arch/arm/boot/dts/am335x-base0033.dts index b4f95c2..72a9b3f 100644 --- a/arch/arm/boot/dts/am335x-base0033.dts +++ b/arch/arm/boot/dts/am335x-base0033.dts @@ -13,4 +13,83 @@ / { model = "IGEP COM AM335x on AQUILA Expansion"; compatible = "isee,am335x-base0033", "isee,am335x-igep0033", "ti,am33xx"; + + hdmi { + compatible = "ti,tilcdc,slave"; + i2c = <&i2c0>; + pinctrl-names = "default", "off"; + pinctrl-0 = <&nxp_hdmi_pins>; + pinctrl-1 = <&nxp_hdmi_off_pins>; + status = "okay"; + }; + + leds_base { + pinctrl-names = "default"; + pinctrl-0 = <&leds_base_pins>; + + compatible = "gpio-leds"; + + led@0 { + label = "base:red:user"; + gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>; /* gpio1_21 */ + default-state = "off"; + }; + + led@1 { + label = "base:green:user"; + gpios = <&gpio2 0 GPIO_ACTIVE_HIGH>; /* gpio2_0 */ + default-state = "off"; + }; + }; +}; + +&am33xx_pinmux { + nxp_hdmi_pins: pinmux_nxp_hdmi_pins { + pinctrl-single,pins = < + 0x1b0 (PIN_OUTPUT | MUX_MODE3) /* xdma_event_intr0.clkout1 */ + 0xa0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data0 */ + 0xa4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data1 */ + 0xa8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data2 */ + 0xac (PIN_OUTPUT | MUX_MODE0) /* lcd_data3 */ + 0xb0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data4 */ + 0xb4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data5 */ + 0xb8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data6 */ + 0xbc (PIN_OUTPUT | MUX_MODE0) /* lcd_data7 */ + 0xc0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data8 */ + 0xc4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data9 */ + 0xc8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data10 */ + 0xcc (PIN_OUTPUT | MUX_MODE0) /* lcd_data11 */ + 0xd0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data12 */ + 0xd4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data13 */ + 0xd8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data14 */ + 0xdc (PIN_OUTPUT | MUX_MODE0) /* lcd_data15 */ + 0xe0 (PIN_OUTPUT | MUX_MODE0) /* lcd_vsync */ + 0xe4 (PIN_OUTPUT | MUX_MODE0) /* lcd_hsync */ + 0xe8 (PIN_OUTPUT | MUX_MODE0) /* lcd_pclk */ + 0xec (PIN_OUTPUT | MUX_MODE0) /* lcd_ac_bias_en */ + >; + }; + nxp_hdmi_off_pins: pinmux_nxp_hdmi_off_pins { + pinctrl-single,pins = < + 0x1b0 (PIN_OUTPUT | MUX_MODE3) /* xdma_event_intr0.clkout1 */ + >; + }; + + leds_base_pins: pinmux_leds_base_pins { + pinctrl-single,pins = < + 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a5.gpio1_21 */ + 0x88 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_csn3.gpio2_0 */ + >; + }; +}; + +&lcdc { + status = "okay"; +}; + +&i2c0 { + eeprom: eeprom@50 { + compatible = "at,24c256"; + reg = <0x50>; + }; }; diff --git a/arch/arm/boot/dts/am335x-igep0033.dtsi b/arch/arm/boot/dts/am335x-igep0033.dtsi index 6196244..7063311 100644 --- a/arch/arm/boot/dts/am335x-igep0033.dtsi +++ b/arch/arm/boot/dts/am335x-igep0033.dtsi @@ -199,6 +199,35 @@ pinctrl-0 = <&uart0_pins>; }; +&usb { + status = "okay"; + + control@44e10000 { + status = "okay"; + }; + + usb-phy@47401300 { + status = "okay"; + }; + + usb-phy@47401b00 { + status = "okay"; + }; + + usb@47401000 { + status = "okay"; + }; + + usb@47401800 { + status = "okay"; + dr_mode = "host"; + }; + + dma-controller@07402000 { + status = "okay"; + }; +}; + #include "tps65910.dtsi" &tps { diff --git a/arch/arm/boot/dts/am3517-evm.dts b/arch/arm/boot/dts/am3517-evm.dts index e99dfaf..03fcbf0 100644 --- a/arch/arm/boot/dts/am3517-evm.dts +++ b/arch/arm/boot/dts/am3517-evm.dts @@ -7,11 +7,11 @@ */ /dts-v1/; -#include "omap34xx.dtsi" +#include "am3517.dtsi" / { - model = "TI AM3517 EVM (AM3517/05)"; - compatible = "ti,am3517-evm", "ti,omap3"; + model = "TI AM3517 EVM (AM3517/05 TMDSEVM3517)"; + compatible = "ti,am3517-evm", "ti,am3517", "ti,omap3"; memory { device_type = "memory"; diff --git a/arch/arm/boot/dts/am3517.dtsi b/arch/arm/boot/dts/am3517.dtsi new file mode 100644 index 0000000..2fbe02f --- /dev/null +++ b/arch/arm/boot/dts/am3517.dtsi @@ -0,0 +1,63 @@ +/* + * Device Tree Source for am3517 SoC + * + * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/ + * + * This file is licensed under the terms of the GNU General Public License + * version 2. This program is licensed "as is" without any warranty of any + * kind, whether express or implied. + */ + +#include "omap3.dtsi" + +/ { + aliases { + serial3 = &uart4; + }; + + ocp { + am35x_otg_hs: am35x_otg_hs@5c040000 { + compatible = "ti,omap3-musb"; + ti,hwmods = "am35x_otg_hs"; + status = "disabled"; + reg = <0x5c040000 0x1000>; + interrupts = <71>; + interrupt-names = "mc"; + }; + + davinci_emac: ethernet@0x5c000000 { + compatible = "ti,am3517-emac"; + ti,hwmods = "davinci_emac"; + status = "disabled"; + reg = <0x5c000000 0x30000>; + interrupts = <67 68 69 70>; + ti,davinci-ctrl-reg-offset = <0x10000>; + ti,davinci-ctrl-mod-reg-offset = <0>; + ti,davinci-ctrl-ram-offset = <0x20000>; + ti,davinci-ctrl-ram-size = <0x2000>; + ti,davinci-rmii-en = /bits/ 8 <1>; + local-mac-address = [ 00 00 00 00 00 00 ]; + }; + + davinci_mdio: ethernet@0x5c030000 { + compatible = "ti,davinci_mdio"; + ti,hwmods = "davinci_mdio"; + status = "disabled"; + reg = <0x5c030000 0x1000>; + bus_freq = <1000000>; + #address-cells = <1>; + #size-cells = <0>; + }; + + uart4: serial@4809e000 { + compatible = "ti,omap3-uart"; + ti,hwmods = "uart4"; + status = "disabled"; + reg = <0x4809e000 0x400>; + interrupts = <84>; + dmas = <&sdma 55 &sdma 54>; + dma-names = "tx", "rx"; + clock-frequency = <48000000>; + }; + }; +}; diff --git a/arch/arm/boot/dts/armada-370-db.dts b/arch/arm/boot/dts/armada-370-db.dts index 90ce29d..08a56bc 100644 --- a/arch/arm/boot/dts/armada-370-db.dts +++ b/arch/arm/boot/dts/armada-370-db.dts @@ -99,22 +99,22 @@ spi-max-frequency = <50000000>; }; }; + }; - pcie-controller { + pcie-controller { + status = "okay"; + /* + * The two PCIe units are accessible through + * both standard PCIe slots and mini-PCIe + * slots on the board. + */ + pcie@1,0 { + /* Port 0, Lane 0 */ + status = "okay"; + }; + pcie@2,0 { + /* Port 1, Lane 0 */ status = "okay"; - /* - * The two PCIe units are accessible through - * both standard PCIe slots and mini-PCIe - * slots on the board. - */ - pcie@1,0 { - /* Port 0, Lane 0 */ - status = "okay"; - }; - pcie@2,0 { - /* Port 1, Lane 0 */ - status = "okay"; - }; }; }; }; diff --git a/arch/arm/boot/dts/armada-370-xp.dtsi b/arch/arm/boot/dts/armada-370-xp.dtsi index 00d6a79..7f10f62 100644 --- a/arch/arm/boot/dts/armada-370-xp.dtsi +++ b/arch/arm/boot/dts/armada-370-xp.dtsi @@ -118,7 +118,7 @@ coherency-fabric@20200 { compatible = "marvell,coherency-fabric"; - reg = <0x20200 0xb0>, <0x21810 0x1c>; + reg = <0x20200 0xb0>, <0x21010 0x1c>; }; serial@12000 { diff --git a/arch/arm/boot/dts/armada-xp-mv78230.dtsi b/arch/arm/boot/dts/armada-xp-mv78230.dtsi index 3f5e612..98335fb 100644 --- a/arch/arm/boot/dts/armada-xp-mv78230.dtsi +++ b/arch/arm/boot/dts/armada-xp-mv78230.dtsi @@ -47,7 +47,7 @@ /* * MV78230 has 2 PCIe units Gen2.0: One unit can be * configured as x4 or quad x1 lanes. One unit is - * x4/x1. + * x1 only. */ pcie-controller { compatible = "marvell,armada-xp-pcie"; @@ -62,10 +62,10 @@ ranges = <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000 /* Port 0.0 registers */ - 0x82000000 0 0x42000 MBUS_ID(0xf0, 0x01) 0x42000 0 0x00002000 /* Port 2.0 registers */ 0x82000000 0 0x44000 MBUS_ID(0xf0, 0x01) 0x44000 0 0x00002000 /* Port 0.1 registers */ 0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000 /* Port 0.2 registers */ 0x82000000 0 0x4c000 MBUS_ID(0xf0, 0x01) 0x4c000 0 0x00002000 /* Port 0.3 registers */ + 0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000 /* Port 1.0 registers */ 0x82000000 0x1 0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 MEM */ 0x81000000 0x1 0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 IO */ 0x82000000 0x2 0 MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 0.1 MEM */ @@ -74,8 +74,8 @@ 0x81000000 0x3 0 MBUS_ID(0x04, 0xb0) 0 1 0 /* Port 0.2 IO */ 0x82000000 0x4 0 MBUS_ID(0x04, 0x78) 0 1 0 /* Port 0.3 MEM */ 0x81000000 0x4 0 MBUS_ID(0x04, 0x70) 0 1 0 /* Port 0.3 IO */ - 0x82000000 0x9 0 MBUS_ID(0x04, 0xf8) 0 1 0 /* Port 2.0 MEM */ - 0x81000000 0x9 0 MBUS_ID(0x04, 0xf0) 0 1 0 /* Port 2.0 IO */>; + 0x82000000 0x5 0 MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 1.0 MEM */ + 0x81000000 0x5 0 MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 1.0 IO */>; pcie@1,0 { device_type = "pci"; @@ -145,20 +145,20 @@ status = "disabled"; }; - pcie@9,0 { + pcie@5,0 { device_type = "pci"; - assigned-addresses = <0x82000800 0 0x42000 0 0x2000>; - reg = <0x4800 0 0 0 0>; + assigned-addresses = <0x82000800 0 0x80000 0 0x2000>; + reg = <0x2800 0 0 0 0>; #address-cells = <3>; #size-cells = <2>; #interrupt-cells = <1>; - ranges = <0x82000000 0 0 0x82000000 0x9 0 1 0 - 0x81000000 0 0 0x81000000 0x9 0 1 0>; + ranges = <0x82000000 0 0 0x82000000 0x5 0 1 0 + 0x81000000 0 0 0x81000000 0x5 0 1 0>; interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &mpic 99>; - marvell,pcie-port = <2>; + interrupt-map = <0 0 0 0 &mpic 62>; + marvell,pcie-port = <1>; marvell,pcie-lane = <0>; - clocks = <&gateclk 26>; + clocks = <&gateclk 9>; status = "disabled"; }; }; diff --git a/arch/arm/boot/dts/armada-xp-mv78260.dtsi b/arch/arm/boot/dts/armada-xp-mv78260.dtsi index 3e9fd13..6660968 100644 --- a/arch/arm/boot/dts/armada-xp-mv78260.dtsi +++ b/arch/arm/boot/dts/armada-xp-mv78260.dtsi @@ -48,7 +48,7 @@ /* * MV78260 has 3 PCIe units Gen2.0: Two units can be * configured as x4 or quad x1 lanes. One unit is - * x4/x1. + * x4 only. */ pcie-controller { compatible = "marvell,armada-xp-pcie"; @@ -68,7 +68,9 @@ 0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000 /* Port 0.2 registers */ 0x82000000 0 0x4c000 MBUS_ID(0xf0, 0x01) 0x4c000 0 0x00002000 /* Port 0.3 registers */ 0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000 /* Port 1.0 registers */ - 0x82000000 0 0x82000 MBUS_ID(0xf0, 0x01) 0x82000 0 0x00002000 /* Port 3.0 registers */ + 0x82000000 0 0x84000 MBUS_ID(0xf0, 0x01) 0x84000 0 0x00002000 /* Port 1.1 registers */ + 0x82000000 0 0x88000 MBUS_ID(0xf0, 0x01) 0x88000 0 0x00002000 /* Port 1.2 registers */ + 0x82000000 0 0x8c000 MBUS_ID(0xf0, 0x01) 0x8c000 0 0x00002000 /* Port 1.3 registers */ 0x82000000 0x1 0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 MEM */ 0x81000000 0x1 0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 IO */ 0x82000000 0x2 0 MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 0.1 MEM */ @@ -77,10 +79,18 @@ 0x81000000 0x3 0 MBUS_ID(0x04, 0xb0) 0 1 0 /* Port 0.2 IO */ 0x82000000 0x4 0 MBUS_ID(0x04, 0x78) 0 1 0 /* Port 0.3 MEM */ 0x81000000 0x4 0 MBUS_ID(0x04, 0x70) 0 1 0 /* Port 0.3 IO */ - 0x82000000 0x9 0 MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 1.0 MEM */ - 0x81000000 0x9 0 MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 1.0 IO */ - 0x82000000 0xa 0 MBUS_ID(0x08, 0xf8) 0 1 0 /* Port 3.0 MEM */ - 0x81000000 0xa 0 MBUS_ID(0x08, 0xf0) 0 1 0 /* Port 3.0 IO */>; + + 0x82000000 0x5 0 MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 1.0 MEM */ + 0x81000000 0x5 0 MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 1.0 IO */ + 0x82000000 0x6 0 MBUS_ID(0x08, 0xd8) 0 1 0 /* Port 1.1 MEM */ + 0x81000000 0x6 0 MBUS_ID(0x08, 0xd0) 0 1 0 /* Port 1.1 IO */ + 0x82000000 0x7 0 MBUS_ID(0x08, 0xb8) 0 1 0 /* Port 1.2 MEM */ + 0x81000000 0x7 0 MBUS_ID(0x08, 0xb0) 0 1 0 /* Port 1.2 IO */ + 0x82000000 0x8 0 MBUS_ID(0x08, 0x78) 0 1 0 /* Port 1.3 MEM */ + 0x81000000 0x8 0 MBUS_ID(0x08, 0x70) 0 1 0 /* Port 1.3 IO */ + + 0x82000000 0x9 0 MBUS_ID(0x04, 0xf8) 0 1 0 /* Port 2.0 MEM */ + 0x81000000 0x9 0 MBUS_ID(0x04, 0xf0) 0 1 0 /* Port 2.0 IO */>; pcie@1,0 { device_type = "pci"; @@ -106,8 +116,8 @@ #address-cells = <3>; #size-cells = <2>; #interrupt-cells = <1>; - ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0 - 0x81000000 0 0 0x81000000 0x2 0 1 0>; + ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0 + 0x81000000 0 0 0x81000000 0x2 0 1 0>; interrupt-map-mask = <0 0 0 0>; interrupt-map = <0 0 0 0 &mpic 59>; marvell,pcie-port = <0>; @@ -150,37 +160,88 @@ status = "disabled"; }; - pcie@9,0 { + pcie@5,0 { device_type = "pci"; - assigned-addresses = <0x82000800 0 0x42000 0 0x2000>; - reg = <0x4800 0 0 0 0>; + assigned-addresses = <0x82000800 0 0x80000 0 0x2000>; + reg = <0x2800 0 0 0 0>; #address-cells = <3>; #size-cells = <2>; #interrupt-cells = <1>; - ranges = <0x82000000 0 0 0x82000000 0x9 0 1 0 - 0x81000000 0 0 0x81000000 0x9 0 1 0>; + ranges = <0x82000000 0 0 0x82000000 0x5 0 1 0 + 0x81000000 0 0 0x81000000 0x5 0 1 0>; interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &mpic 99>; - marvell,pcie-port = <2>; + interrupt-map = <0 0 0 0 &mpic 62>; + marvell,pcie-port = <1>; marvell,pcie-lane = <0>; - clocks = <&gateclk 26>; + clocks = <&gateclk 9>; status = "disabled"; }; - pcie@10,0 { + pcie@6,0 { device_type = "pci"; - assigned-addresses = <0x82000800 0 0x82000 0 0x2000>; - reg = <0x5000 0 0 0 0>; + assigned-addresses = <0x82000800 0 0x84000 0 0x2000>; + reg = <0x3000 0 0 0 0>; #address-cells = <3>; #size-cells = <2>; #interrupt-cells = <1>; - ranges = <0x82000000 0 0 0x82000000 0xa 0 1 0 - 0x81000000 0 0 0x81000000 0xa 0 1 0>; + ranges = <0x82000000 0 0 0x82000000 0x6 0 1 0 + 0x81000000 0 0 0x81000000 0x6 0 1 0>; interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &mpic 103>; - marvell,pcie-port = <3>; + interrupt-map = <0 0 0 0 &mpic 63>; + marvell,pcie-port = <1>; + marvell,pcie-lane = <1>; + clocks = <&gateclk 10>; + status = "disabled"; + }; + + pcie@7,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x88000 0 0x2000>; + reg = <0x3800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x7 0 1 0 + 0x81000000 0 0 0x81000000 0x7 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 64>; + marvell,pcie-port = <1>; + marvell,pcie-lane = <2>; + clocks = <&gateclk 11>; + status = "disabled"; + }; + + pcie@8,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x8c000 0 0x2000>; + reg = <0x4000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x8 0 1 0 + 0x81000000 0 0 0x81000000 0x8 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 65>; + marvell,pcie-port = <1>; + marvell,pcie-lane = <3>; + clocks = <&gateclk 12>; + status = "disabled"; + }; + + pcie@9,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x42000 0 0x2000>; + reg = <0x4800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x9 0 1 0 + 0x81000000 0 0 0x81000000 0x9 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 99>; + marvell,pcie-port = <2>; marvell,pcie-lane = <0>; - clocks = <&gateclk 27>; + clocks = <&gateclk 26>; status = "disabled"; }; }; diff --git a/arch/arm/boot/dts/at91sam9x5_usart3.dtsi b/arch/arm/boot/dts/at91sam9x5_usart3.dtsi index 2347e95..6801106 100644 --- a/arch/arm/boot/dts/at91sam9x5_usart3.dtsi +++ b/arch/arm/boot/dts/at91sam9x5_usart3.dtsi @@ -11,6 +11,10 @@ #include <dt-bindings/interrupt-controller/irq.h> / { + aliases { + serial4 = &usart3; + }; + ahb { apb { pinctrl@fffff400 { diff --git a/arch/arm/boot/dts/exynos5250.dtsi b/arch/arm/boot/dts/exynos5250.dtsi index 9db5047..177becd 100644 --- a/arch/arm/boot/dts/exynos5250.dtsi +++ b/arch/arm/boot/dts/exynos5250.dtsi @@ -559,7 +559,7 @@ compatible = "arm,pl330", "arm,primecell"; reg = <0x10800000 0x1000>; interrupts = <0 33 0>; - clocks = <&clock 271>; + clocks = <&clock 346>; clock-names = "apb_pclk"; #dma-cells = <1>; #dma-channels = <8>; diff --git a/arch/arm/boot/dts/omap-gpmc-smsc911x.dtsi b/arch/arm/boot/dts/omap-gpmc-smsc911x.dtsi index 9c18adf..f577b7d 100644 --- a/arch/arm/boot/dts/omap-gpmc-smsc911x.dtsi +++ b/arch/arm/boot/dts/omap-gpmc-smsc911x.dtsi @@ -44,8 +44,8 @@ gpmc,wr-access-ns = <186>; gpmc,cycle2cycle-samecsen; gpmc,cycle2cycle-diffcsen; - vmmc-supply = <&vddvario>; - vmmc_aux-supply = <&vdd33a>; + vddvario-supply = <&vddvario>; + vdd33a-supply = <&vdd33a>; reg-io-width = <4>; smsc,save-mac-address; }; diff --git a/arch/arm/boot/dts/omap3-beagle-xm.dts b/arch/arm/boot/dts/omap3-beagle-xm.dts index 31a632f..df33a50 100644 --- a/arch/arm/boot/dts/omap3-beagle-xm.dts +++ b/arch/arm/boot/dts/omap3-beagle-xm.dts @@ -215,3 +215,10 @@ &usbhsehci { phys = <0 &hsusb2_phy>; }; + +&vaux2 { + regulator-name = "usb_1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; +}; diff --git a/arch/arm/boot/dts/omap3-beagle.dts b/arch/arm/boot/dts/omap3-beagle.dts index fa532aa..3ba4a62 100644 --- a/arch/arm/boot/dts/omap3-beagle.dts +++ b/arch/arm/boot/dts/omap3-beagle.dts @@ -61,6 +61,14 @@ vcc-supply = <&hsusb2_power>; }; + sound { + compatible = "ti,omap-twl4030"; + ti,model = "omap3beagle"; + + ti,mcbsp = <&mcbsp2>; + ti,codec = <&twl_audio>; + }; + gpio_keys { compatible = "gpio-keys"; @@ -120,6 +128,12 @@ reg = <0x48>; interrupts = <7>; /* SYS_NIRQ cascaded to intc */ interrupt-parent = <&intc>; + + twl_audio: audio { + compatible = "ti,twl4030-audio"; + codec { + }; + }; }; }; @@ -178,3 +192,10 @@ mode = <3>; power = <50>; }; + +&vaux2 { + regulator-name = "vdd_ehci"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; +}; diff --git a/arch/arm/boot/dts/omap3-igep.dtsi b/arch/arm/boot/dts/omap3-igep.dtsi index ba1e58b..165aaf7 100644 --- a/arch/arm/boot/dts/omap3-igep.dtsi +++ b/arch/arm/boot/dts/omap3-igep.dtsi @@ -1,5 +1,5 @@ /* - * Device Tree Source for IGEP Technology devices + * Common device tree for IGEP boards based on AM/DM37x * * Copyright (C) 2012 Javier Martinez Canillas <javier@collabora.co.uk> * Copyright (C) 2012 Enric Balletbo i Serra <eballetbo@gmail.com> @@ -10,7 +10,7 @@ */ /dts-v1/; -#include "omap34xx.dtsi" +#include "omap36xx.dtsi" / { memory { @@ -24,6 +24,25 @@ ti,mcbsp = <&mcbsp2>; ti,codec = <&twl_audio>; }; + + vdd33: regulator-vdd33 { + compatible = "regulator-fixed"; + regulator-name = "vdd33"; + regulator-always-on; + }; + + lbee1usjyc_vmmc: lbee1usjyc_vmmc { + pinctrl-names = "default"; + pinctrl-0 = <&lbee1usjyc_pins>; + compatible = "regulator-fixed"; + regulator-name = "regulator-lbee1usjyc"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio5 10 GPIO_ACTIVE_HIGH>; /* gpio_138 WIFI_PDN */ + startup-delay-us = <10000>; + enable-active-high; + vin-supply = <&vdd33>; + }; }; &omap3_pmx_core { @@ -48,6 +67,15 @@ >; }; + /* WiFi/BT combo */ + lbee1usjyc_pins: pinmux_lbee1usjyc_pins { + pinctrl-single,pins = < + 0x136 (PIN_OUTPUT | MUX_MODE4) /* sdmmc2_dat5.gpio_137 */ + 0x138 (PIN_OUTPUT | MUX_MODE4) /* sdmmc2_dat6.gpio_138 */ + 0x13a (PIN_OUTPUT | MUX_MODE4) /* sdmmc2_dat7.gpio_139 */ + >; + }; + mcbsp2_pins: pinmux_mcbsp2_pins { pinctrl-single,pins = < 0x10c (PIN_INPUT | MUX_MODE0) /* mcbsp2_fsx.mcbsp2_fsx */ @@ -65,10 +93,17 @@ 0x11a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */ 0x11c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */ 0x11e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ - 0x120 (PIN_INPUT | MUX_MODE0) /* sdmmc1_dat4.sdmmc1_dat4 */ - 0x122 (PIN_INPUT | MUX_MODE0) /* sdmmc1_dat5.sdmmc1_dat5 */ - 0x124 (PIN_INPUT | MUX_MODE0) /* sdmmc1_dat6.sdmmc1_dat6 */ - 0x126 (PIN_INPUT | MUX_MODE0) /* sdmmc1_dat7.sdmmc1_dat7 */ + >; + }; + + mmc2_pins: pinmux_mmc2_pins { + pinctrl-single,pins = < + 0x128 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */ + 0x12a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */ + 0x12c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */ + 0x12e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */ + 0x130 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */ + 0x132 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */ >; }; @@ -78,10 +113,33 @@ >; }; + i2c1_pins: pinmux_i2c1_pins { + pinctrl-single,pins = < + 0x18a (PIN_INPUT | MUX_MODE0) /* i2c1_scl.i2c1_scl */ + 0x18c (PIN_INPUT | MUX_MODE0) /* i2c1_sda.i2c1_sda */ + >; + }; + + i2c2_pins: pinmux_i2c2_pins { + pinctrl-single,pins = < + 0x18e (PIN_INPUT | MUX_MODE0) /* i2c2_scl.i2c2_scl */ + 0x190 (PIN_INPUT | MUX_MODE0) /* i2c2_sda.i2c2_sda */ + >; + }; + + i2c3_pins: pinmux_i2c3_pins { + pinctrl-single,pins = < + 0x192 (PIN_INPUT | MUX_MODE0) /* i2c3_scl.i2c3_scl */ + 0x194 (PIN_INPUT | MUX_MODE0) /* i2c3_sda.i2c3_sda */ + >; + }; + leds_pins: pinmux_leds_pins { }; }; &i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; clock-frequency = <2600000>; twl: twl@48 { @@ -101,9 +159,16 @@ #include "twl4030_omap3.dtsi" &i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins>; clock-frequency = <400000>; }; +&i2c3 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c3_pins>; +}; + &mcbsp2 { pinctrl-names = "default"; pinctrl-0 = <&mcbsp2_pins>; @@ -114,11 +179,15 @@ pinctrl-0 = <&mmc1_pins>; vmmc-supply = <&vmmc1>; vmmc_aux-supply = <&vsim>; - bus-width = <8>; + bus-width = <4>; }; &mmc2 { - status = "disabled"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins>; + vmmc-supply = <&lbee1usjyc_vmmc>; + bus-width = <4>; + non-removable; }; &mmc3 { diff --git a/arch/arm/boot/dts/omap3-igep0020.dts b/arch/arm/boot/dts/omap3-igep0020.dts index d5cc792..1c7e74d 100644 --- a/arch/arm/boot/dts/omap3-igep0020.dts +++ b/arch/arm/boot/dts/omap3-igep0020.dts @@ -1,5 +1,5 @@ /* - * Device Tree Source for IGEPv2 board + * Device Tree Source for IGEPv2 Rev. (TI OMAP AM/DM37x) * * Copyright (C) 2012 Javier Martinez Canillas <javier@collabora.co.uk> * Copyright (C) 2012 Enric Balletbo i Serra <eballetbo@gmail.com> @@ -13,7 +13,7 @@ #include "omap-gpmc-smsc911x.dtsi" / { - model = "IGEPv2"; + model = "IGEPv2 (TI OMAP AM/DM37x)"; compatible = "isee,omap3-igep0020", "ti,omap3"; leds { @@ -67,6 +67,8 @@ pinctrl-names = "default"; pinctrl-0 = < &hsusbb1_pins + &tfp410_pins + &dss_pins >; hsusbb1_pins: pinmux_hsusbb1_pins { @@ -85,6 +87,45 @@ 0x5ba (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d7.hsusb1_data3 */ >; }; + + tfp410_pins: tfp410_dvi_pins { + pinctrl-single,pins = < + 0x196 (PIN_OUTPUT | MUX_MODE4) /* hdq_sio.gpio_170 */ + >; + }; + + dss_pins: pinmux_dss_dvi_pins { + pinctrl-single,pins = < + 0x0a4 (PIN_OUTPUT | MUX_MODE0) /* dss_pclk.dss_pclk */ + 0x0a6 (PIN_OUTPUT | MUX_MODE0) /* dss_hsync.dss_hsync */ + 0x0a8 (PIN_OUTPUT | MUX_MODE0) /* dss_vsync.dss_vsync */ + 0x0aa (PIN_OUTPUT | MUX_MODE0) /* dss_acbias.dss_acbias */ + 0x0ac (PIN_OUTPUT | MUX_MODE0) /* dss_data0.dss_data0 */ + 0x0ae (PIN_OUTPUT | MUX_MODE0) /* dss_data1.dss_data1 */ + 0x0b0 (PIN_OUTPUT | MUX_MODE0) /* dss_data2.dss_data2 */ + 0x0b2 (PIN_OUTPUT | MUX_MODE0) /* dss_data3.dss_data3 */ + 0x0b4 (PIN_OUTPUT | MUX_MODE0) /* dss_data4.dss_data4 */ + 0x0b6 (PIN_OUTPUT | MUX_MODE0) /* dss_data5.dss_data5 */ + 0x0b8 (PIN_OUTPUT | MUX_MODE0) /* dss_data6.dss_data6 */ + 0x0ba (PIN_OUTPUT | MUX_MODE0) /* dss_data7.dss_data7 */ + 0x0bc (PIN_OUTPUT | MUX_MODE0) /* dss_data8.dss_data8 */ + 0x0be (PIN_OUTPUT | MUX_MODE0) /* dss_data9.dss_data9 */ + 0x0c0 (PIN_OUTPUT | MUX_MODE0) /* dss_data10.dss_data10 */ + 0x0c2 (PIN_OUTPUT | MUX_MODE0) /* dss_data11.dss_data11 */ + 0x0c4 (PIN_OUTPUT | MUX_MODE0) /* dss_data12.dss_data12 */ + 0x0c6 (PIN_OUTPUT | MUX_MODE0) /* dss_data13.dss_data13 */ + 0x0c8 (PIN_OUTPUT | MUX_MODE0) /* dss_data14.dss_data14 */ + 0x0ca (PIN_OUTPUT | MUX_MODE0) /* dss_data15.dss_data15 */ + 0x0cc (PIN_OUTPUT | MUX_MODE0) /* dss_data16.dss_data16 */ + 0x0ce (PIN_OUTPUT | MUX_MODE0) /* dss_data17.dss_data17 */ + 0x0d0 (PIN_OUTPUT | MUX_MODE0) /* dss_data18.dss_data18 */ + 0x0d2 (PIN_OUTPUT | MUX_MODE0) /* dss_data19.dss_data19 */ + 0x0d4 (PIN_OUTPUT | MUX_MODE0) /* dss_data20.dss_data20 */ + 0x0d6 (PIN_OUTPUT | MUX_MODE0) /* dss_data21.dss_data21 */ + 0x0d8 (PIN_OUTPUT | MUX_MODE0) /* dss_data22.dss_data22 */ + 0x0da (PIN_OUTPUT | MUX_MODE0) /* dss_data23.dss_data23 */ + >; + }; }; &leds_pins { @@ -174,3 +215,8 @@ &usbhsehci { phys = <&hsusb1_phy>; }; + +&vpll2 { + /* Needed for DSS */ + regulator-name = "vdds_dsi"; +}; diff --git a/arch/arm/boot/dts/omap3-igep0030.dts b/arch/arm/boot/dts/omap3-igep0030.dts index 525e6d9..02a23f8 100644 --- a/arch/arm/boot/dts/omap3-igep0030.dts +++ b/arch/arm/boot/dts/omap3-igep0030.dts @@ -1,5 +1,5 @@ /* - * Device Tree Source for IGEP COM Module + * Device Tree Source for IGEP COM MODULE (TI OMAP AM/DM37x) * * Copyright (C) 2012 Javier Martinez Canillas <javier@collabora.co.uk> * Copyright (C) 2012 Enric Balletbo i Serra <eballetbo@gmail.com> @@ -12,7 +12,7 @@ #include "omap3-igep.dtsi" / { - model = "IGEP COM Module"; + model = "IGEP COM MODULE (TI OMAP AM/DM37x)"; compatible = "isee,omap3-igep0030", "ti,omap3"; leds { diff --git a/arch/arm/boot/dts/omap3-n900.dts b/arch/arm/boot/dts/omap3-n900.dts index c4f20bf..6fc85f9 100644 --- a/arch/arm/boot/dts/omap3-n900.dts +++ b/arch/arm/boot/dts/omap3-n900.dts @@ -9,7 +9,7 @@ /dts-v1/; -#include "omap34xx.dtsi" +#include "omap34xx-hs.dtsi" / { model = "Nokia N900"; @@ -125,6 +125,21 @@ >; }; + mmc2_pins: pinmux_mmc2_pins { + pinctrl-single,pins = < + 0x128 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk */ + 0x12a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd */ + 0x12c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0 */ + 0x12e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1 */ + 0x130 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2 */ + 0x132 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3 */ + 0x134 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat4 */ + 0x136 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat5 */ + 0x138 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat6 */ + 0x13a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat7 */ + >; + }; + display_pins: pinmux_display_pins { pinctrl-single,pins = < 0x0d4 (PIN_OUTPUT | MUX_MODE4) /* RX51_LCD_RESET_GPIO */ @@ -358,8 +373,14 @@ cd-gpios = <&gpio6 0 GPIO_ACTIVE_HIGH>; /* 160 */ }; +/* most boards use vaux3, only some old versions use vmmc2 instead */ &mmc2 { - status = "disabled"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins>; + vmmc-supply = <&vaux3>; + vmmc_aux-supply = <&vsim>; + bus-width = <8>; + non-removable; }; &mmc3 { diff --git a/arch/arm/boot/dts/omap3-n950-n9.dtsi b/arch/arm/boot/dts/omap3-n950-n9.dtsi index 94eb77d..5c26c18 100644 --- a/arch/arm/boot/dts/omap3-n950-n9.dtsi +++ b/arch/arm/boot/dts/omap3-n950-n9.dtsi @@ -8,7 +8,7 @@ * published by the Free Software Foundation. */ -#include "omap36xx.dtsi" +#include "omap36xx-hs.dtsi" / { cpus { diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi index f3a0c26..daabf99 100644 --- a/arch/arm/boot/dts/omap3.dtsi +++ b/arch/arm/boot/dts/omap3.dtsi @@ -82,6 +82,13 @@ ranges; ti,hwmods = "l3_main"; + aes: aes@480c5000 { + compatible = "ti,omap3-aes"; + ti,hwmods = "aes"; + reg = <0x480c5000 0x50>; + interrupts = <0>; + }; + counter32k: counter@48320000 { compatible = "ti,omap-counter32k"; reg = <0x48320000 0x20>; @@ -260,6 +267,13 @@ ti,hwmods = "i2c3"; }; + mailbox: mailbox@48094000 { + compatible = "ti,omap3-mailbox"; + ti,hwmods = "mailbox"; + reg = <0x48094000 0x200>; + interrupts = <26>; + }; + mcspi1: spi@48098000 { compatible = "ti,omap2-mcspi"; reg = <0x48098000 0x100>; @@ -357,6 +371,13 @@ dma-names = "tx", "rx"; }; + mmu_isp: mmu@480bd400 { + compatible = "ti,omap3-mmu-isp"; + ti,hwmods = "mmu_isp"; + reg = <0x480bd400 0x80>; + interrupts = <8>; + }; + wdt2: wdt@48314000 { compatible = "ti,omap3-wdt"; reg = <0x48314000 0x80>; @@ -442,6 +463,27 @@ dma-names = "tx", "rx"; }; + sham: sham@480c3000 { + compatible = "ti,omap3-sham"; + ti,hwmods = "sham"; + reg = <0x480c3000 0x64>; + interrupts = <49>; + }; + + smartreflex_core: smartreflex@480cb000 { + compatible = "ti,omap3-smartreflex-core"; + ti,hwmods = "smartreflex_core"; + reg = <0x480cb000 0x400>; + interrupts = <19>; + }; + + smartreflex_mpu_iva: smartreflex@480c9000 { + compatible = "ti,omap3-smartreflex-iva"; + ti,hwmods = "smartreflex_mpu_iva"; + reg = <0x480c9000 0x400>; + interrupts = <18>; + }; + timer1: timer@48318000 { compatible = "ti,omap3430-timer"; reg = <0x48318000 0x400>; diff --git a/arch/arm/boot/dts/omap34xx-hs.dtsi b/arch/arm/boot/dts/omap34xx-hs.dtsi new file mode 100644 index 0000000..1ff6264 --- /dev/null +++ b/arch/arm/boot/dts/omap34xx-hs.dtsi @@ -0,0 +1,16 @@ +/* Disabled modules for secure omaps */ + +#include "omap34xx.dtsi" + +/* Secure omaps have some devices inaccessible depending on the firmware */ +&aes { + status = "disabled"; +}; + +&sham { + status = "disabled"; +}; + +&timer12 { + status = "disabled"; +}; diff --git a/arch/arm/boot/dts/omap36xx-hs.dtsi b/arch/arm/boot/dts/omap36xx-hs.dtsi new file mode 100644 index 0000000..2c7febb --- /dev/null +++ b/arch/arm/boot/dts/omap36xx-hs.dtsi @@ -0,0 +1,16 @@ +/* Disabled modules for secure omaps */ + +#include "omap36xx.dtsi" + +/* Secure omaps have some devices inaccessible depending on the firmware */ +&aes { + status = "disabled"; +}; + +&sham { + status = "disabled"; +}; + +&timer12 { + status = "disabled"; +}; diff --git a/arch/arm/boot/dts/omap4-panda-common.dtsi b/arch/arm/boot/dts/omap4-panda-common.dtsi index 298e850..88c6a05 100644 --- a/arch/arm/boot/dts/omap4-panda-common.dtsi +++ b/arch/arm/boot/dts/omap4-panda-common.dtsi @@ -246,15 +246,6 @@ 0xf0 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_sda */ >; }; -}; - -&omap4_pmx_wkup { - led_wkgpio_pins: pinmux_leds_wkpins { - pinctrl-single,pins = < - 0x1a (PIN_OUTPUT | MUX_MODE3) /* gpio_wk7 */ - 0x1c (PIN_OUTPUT | MUX_MODE3) /* gpio_wk8 */ - >; - }; /* * wl12xx GPIO outputs for WLAN_EN, BT_EN, FM_EN, BT_WAKEUP @@ -274,7 +265,7 @@ pinctrl-single,pins = < 0x38 (PIN_INPUT | MUX_MODE3) /* gpmc_ncs2.gpio_52 */ 0x3a (PIN_INPUT | MUX_MODE3) /* gpmc_ncs3.gpio_53 */ - 0x108 (PIN_OUTPUT | MUX_MODE0) /* sdmmc5_clk.sdmmc5_clk */ + 0x108 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_clk.sdmmc5_clk */ 0x10a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_cmd.sdmmc5_cmd */ 0x10c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat0.sdmmc5_dat0 */ 0x10e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat1.sdmmc5_dat1 */ @@ -284,6 +275,15 @@ }; }; +&omap4_pmx_wkup { + led_wkgpio_pins: pinmux_leds_wkpins { + pinctrl-single,pins = < + 0x1a (PIN_OUTPUT | MUX_MODE3) /* gpio_wk7 */ + 0x1c (PIN_OUTPUT | MUX_MODE3) /* gpio_wk8 */ + >; + }; +}; + &i2c1 { pinctrl-names = "default"; pinctrl-0 = <&i2c1_pins>; diff --git a/arch/arm/boot/dts/omap4-sdp.dts b/arch/arm/boot/dts/omap4-sdp.dts index 5fc3f43..dbc81fb 100644 --- a/arch/arm/boot/dts/omap4-sdp.dts +++ b/arch/arm/boot/dts/omap4-sdp.dts @@ -300,12 +300,12 @@ wl12xx_pins: pinmux_wl12xx_pins { pinctrl-single,pins = < 0x3a (PIN_INPUT | MUX_MODE3) /* gpmc_ncs3.gpio_53 */ - 0x108 (PIN_OUTPUT | MUX_MODE3) /* sdmmc5_clk.sdmmc5_clk */ - 0x10a (PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc5_cmd.sdmmc5_cmd */ - 0x10c (PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc5_dat0.sdmmc5_dat0 */ - 0x10e (PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc5_dat1.sdmmc5_dat1 */ - 0x110 (PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc5_dat2.sdmmc5_dat2 */ - 0x112 (PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc5_dat3.sdmmc5_dat3 */ + 0x108 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_clk.sdmmc5_clk */ + 0x10a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_cmd.sdmmc5_cmd */ + 0x10c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat0.sdmmc5_dat0 */ + 0x10e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat1.sdmmc5_dat1 */ + 0x110 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat2.sdmmc5_dat2 */ + 0x112 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat3.sdmmc5_dat3 */ >; }; }; diff --git a/arch/arm/boot/dts/r8a7790.dtsi b/arch/arm/boot/dts/r8a7790.dtsi index ee845fa..9987dd0e 100644 --- a/arch/arm/boot/dts/r8a7790.dtsi +++ b/arch/arm/boot/dts/r8a7790.dtsi @@ -87,9 +87,9 @@ interrupts = <1 9 0xf04>; }; - gpio0: gpio@ffc40000 { + gpio0: gpio@e6050000 { compatible = "renesas,gpio-r8a7790", "renesas,gpio-rcar"; - reg = <0 0xffc40000 0 0x2c>; + reg = <0 0xe6050000 0 0x50>; interrupt-parent = <&gic>; interrupts = <0 4 0x4>; #gpio-cells = <2>; @@ -99,9 +99,9 @@ interrupt-controller; }; - gpio1: gpio@ffc41000 { + gpio1: gpio@e6051000 { compatible = "renesas,gpio-r8a7790", "renesas,gpio-rcar"; - reg = <0 0xffc41000 0 0x2c>; + reg = <0 0xe6051000 0 0x50>; interrupt-parent = <&gic>; interrupts = <0 5 0x4>; #gpio-cells = <2>; @@ -111,9 +111,9 @@ interrupt-controller; }; - gpio2: gpio@ffc42000 { + gpio2: gpio@e6052000 { compatible = "renesas,gpio-r8a7790", "renesas,gpio-rcar"; - reg = <0 0xffc42000 0 0x2c>; + reg = <0 0xe6052000 0 0x50>; interrupt-parent = <&gic>; interrupts = <0 6 0x4>; #gpio-cells = <2>; @@ -123,9 +123,9 @@ interrupt-controller; }; - gpio3: gpio@ffc43000 { + gpio3: gpio@e6053000 { compatible = "renesas,gpio-r8a7790", "renesas,gpio-rcar"; - reg = <0 0xffc43000 0 0x2c>; + reg = <0 0xe6053000 0 0x50>; interrupt-parent = <&gic>; interrupts = <0 7 0x4>; #gpio-cells = <2>; @@ -135,9 +135,9 @@ interrupt-controller; }; - gpio4: gpio@ffc44000 { + gpio4: gpio@e6054000 { compatible = "renesas,gpio-r8a7790", "renesas,gpio-rcar"; - reg = <0 0xffc44000 0 0x2c>; + reg = <0 0xe6054000 0 0x50>; interrupt-parent = <&gic>; interrupts = <0 8 0x4>; #gpio-cells = <2>; @@ -147,9 +147,9 @@ interrupt-controller; }; - gpio5: gpio@ffc45000 { + gpio5: gpio@e6055000 { compatible = "renesas,gpio-r8a7790", "renesas,gpio-rcar"; - reg = <0 0xffc45000 0 0x2c>; + reg = <0 0xe6055000 0 0x50>; interrupt-parent = <&gic>; interrupts = <0 9 0x4>; #gpio-cells = <2>; @@ -241,7 +241,7 @@ sdhi0: sdhi@ee100000 { compatible = "renesas,sdhi-r8a7790"; - reg = <0 0xee100000 0 0x100>; + reg = <0 0xee100000 0 0x200>; interrupt-parent = <&gic>; interrupts = <0 165 4>; cap-sd-highspeed; @@ -250,7 +250,7 @@ sdhi1: sdhi@ee120000 { compatible = "renesas,sdhi-r8a7790"; - reg = <0 0xee120000 0 0x100>; + reg = <0 0xee120000 0 0x200>; interrupt-parent = <&gic>; interrupts = <0 166 4>; cap-sd-highspeed; diff --git a/arch/arm/boot/dts/socfpga.dtsi b/arch/arm/boot/dts/socfpga.dtsi index 6d09b8d..f936476 100644 --- a/arch/arm/boot/dts/socfpga.dtsi +++ b/arch/arm/boot/dts/socfpga.dtsi @@ -245,14 +245,14 @@ mpu_periph_clk: mpu_periph_clk { #clock-cells = <0>; - compatible = "altr,socfpga-gate-clk"; + compatible = "altr,socfpga-perip-clk"; clocks = <&mpuclk>; fixed-divider = <4>; }; mpu_l2_ram_clk: mpu_l2_ram_clk { #clock-cells = <0>; - compatible = "altr,socfpga-gate-clk"; + compatible = "altr,socfpga-perip-clk"; clocks = <&mpuclk>; fixed-divider = <2>; }; @@ -266,8 +266,9 @@ l3_main_clk: l3_main_clk { #clock-cells = <0>; - compatible = "altr,socfpga-gate-clk"; + compatible = "altr,socfpga-perip-clk"; clocks = <&mainclk>; + fixed-divider = <1>; }; l3_mp_clk: l3_mp_clk { diff --git a/arch/arm/boot/dts/sun6i-a31.dtsi b/arch/arm/boot/dts/sun6i-a31.dtsi index c1751a6..7f5878c 100644 --- a/arch/arm/boot/dts/sun6i-a31.dtsi +++ b/arch/arm/boot/dts/sun6i-a31.dtsi @@ -193,7 +193,10 @@ pio: pinctrl@01c20800 { compatible = "allwinner,sun6i-a31-pinctrl"; reg = <0x01c20800 0x400>; - interrupts = <0 11 1>, <0 15 1>, <0 16 1>, <0 17 1>; + interrupts = <0 11 4>, + <0 15 4>, + <0 16 4>, + <0 17 4>; clocks = <&apb1_gates 5>; gpio-controller; interrupt-controller; @@ -212,11 +215,11 @@ timer@01c20c00 { compatible = "allwinner,sun4i-timer"; reg = <0x01c20c00 0xa0>; - interrupts = <0 18 1>, - <0 19 1>, - <0 20 1>, - <0 21 1>, - <0 22 1>; + interrupts = <0 18 4>, + <0 19 4>, + <0 20 4>, + <0 21 4>, + <0 22 4>; clocks = <&osc24M>; }; @@ -228,7 +231,7 @@ uart0: serial@01c28000 { compatible = "snps,dw-apb-uart"; reg = <0x01c28000 0x400>; - interrupts = <0 0 1>; + interrupts = <0 0 4>; reg-shift = <2>; reg-io-width = <4>; clocks = <&apb2_gates 16>; @@ -238,7 +241,7 @@ uart1: serial@01c28400 { compatible = "snps,dw-apb-uart"; reg = <0x01c28400 0x400>; - interrupts = <0 1 1>; + interrupts = <0 1 4>; reg-shift = <2>; reg-io-width = <4>; clocks = <&apb2_gates 17>; @@ -248,7 +251,7 @@ uart2: serial@01c28800 { compatible = "snps,dw-apb-uart"; reg = <0x01c28800 0x400>; - interrupts = <0 2 1>; + interrupts = <0 2 4>; reg-shift = <2>; reg-io-width = <4>; clocks = <&apb2_gates 18>; @@ -258,7 +261,7 @@ uart3: serial@01c28c00 { compatible = "snps,dw-apb-uart"; reg = <0x01c28c00 0x400>; - interrupts = <0 3 1>; + interrupts = <0 3 4>; reg-shift = <2>; reg-io-width = <4>; clocks = <&apb2_gates 19>; @@ -268,7 +271,7 @@ uart4: serial@01c29000 { compatible = "snps,dw-apb-uart"; reg = <0x01c29000 0x400>; - interrupts = <0 4 1>; + interrupts = <0 4 4>; reg-shift = <2>; reg-io-width = <4>; clocks = <&apb2_gates 20>; @@ -278,7 +281,7 @@ uart5: serial@01c29400 { compatible = "snps,dw-apb-uart"; reg = <0x01c29400 0x400>; - interrupts = <0 5 1>; + interrupts = <0 5 4>; reg-shift = <2>; reg-io-width = <4>; clocks = <&apb2_gates 21>; diff --git a/arch/arm/boot/dts/sun7i-a20.dtsi b/arch/arm/boot/dts/sun7i-a20.dtsi index e46cfed..367611a 100644 --- a/arch/arm/boot/dts/sun7i-a20.dtsi +++ b/arch/arm/boot/dts/sun7i-a20.dtsi @@ -170,7 +170,7 @@ emac: ethernet@01c0b000 { compatible = "allwinner,sun4i-emac"; reg = <0x01c0b000 0x1000>; - interrupts = <0 55 1>; + interrupts = <0 55 4>; clocks = <&ahb_gates 17>; status = "disabled"; }; @@ -186,7 +186,7 @@ pio: pinctrl@01c20800 { compatible = "allwinner,sun7i-a20-pinctrl"; reg = <0x01c20800 0x400>; - interrupts = <0 28 1>; + interrupts = <0 28 4>; clocks = <&apb0_gates 5>; gpio-controller; interrupt-controller; @@ -251,12 +251,12 @@ timer@01c20c00 { compatible = "allwinner,sun4i-timer"; reg = <0x01c20c00 0x90>; - interrupts = <0 22 1>, - <0 23 1>, - <0 24 1>, - <0 25 1>, - <0 67 1>, - <0 68 1>; + interrupts = <0 22 4>, + <0 23 4>, + <0 24 4>, + <0 25 4>, + <0 67 4>, + <0 68 4>; clocks = <&osc24M>; }; @@ -273,7 +273,7 @@ uart0: serial@01c28000 { compatible = "snps,dw-apb-uart"; reg = <0x01c28000 0x400>; - interrupts = <0 1 1>; + interrupts = <0 1 4>; reg-shift = <2>; reg-io-width = <4>; clocks = <&apb1_gates 16>; @@ -283,7 +283,7 @@ uart1: serial@01c28400 { compatible = "snps,dw-apb-uart"; reg = <0x01c28400 0x400>; - interrupts = <0 2 1>; + interrupts = <0 2 4>; reg-shift = <2>; reg-io-width = <4>; clocks = <&apb1_gates 17>; @@ -293,7 +293,7 @@ uart2: serial@01c28800 { compatible = "snps,dw-apb-uart"; reg = <0x01c28800 0x400>; - interrupts = <0 3 1>; + interrupts = <0 3 4>; reg-shift = <2>; reg-io-width = <4>; clocks = <&apb1_gates 18>; @@ -303,7 +303,7 @@ uart3: serial@01c28c00 { compatible = "snps,dw-apb-uart"; reg = <0x01c28c00 0x400>; - interrupts = <0 4 1>; + interrupts = <0 4 4>; reg-shift = <2>; reg-io-width = <4>; clocks = <&apb1_gates 19>; @@ -313,7 +313,7 @@ uart4: serial@01c29000 { compatible = "snps,dw-apb-uart"; reg = <0x01c29000 0x400>; - interrupts = <0 17 1>; + interrupts = <0 17 4>; reg-shift = <2>; reg-io-width = <4>; clocks = <&apb1_gates 20>; @@ -323,7 +323,7 @@ uart5: serial@01c29400 { compatible = "snps,dw-apb-uart"; reg = <0x01c29400 0x400>; - interrupts = <0 18 1>; + interrupts = <0 18 4>; reg-shift = <2>; reg-io-width = <4>; clocks = <&apb1_gates 21>; @@ -333,7 +333,7 @@ uart6: serial@01c29800 { compatible = "snps,dw-apb-uart"; reg = <0x01c29800 0x400>; - interrupts = <0 19 1>; + interrupts = <0 19 4>; reg-shift = <2>; reg-io-width = <4>; clocks = <&apb1_gates 22>; @@ -343,7 +343,7 @@ uart7: serial@01c29c00 { compatible = "snps,dw-apb-uart"; reg = <0x01c29c00 0x400>; - interrupts = <0 20 1>; + interrupts = <0 20 4>; reg-shift = <2>; reg-io-width = <4>; clocks = <&apb1_gates 23>; @@ -353,7 +353,7 @@ i2c0: i2c@01c2ac00 { compatible = "allwinner,sun4i-i2c"; reg = <0x01c2ac00 0x400>; - interrupts = <0 7 1>; + interrupts = <0 7 4>; clocks = <&apb1_gates 0>; clock-frequency = <100000>; status = "disabled"; @@ -362,7 +362,7 @@ i2c1: i2c@01c2b000 { compatible = "allwinner,sun4i-i2c"; reg = <0x01c2b000 0x400>; - interrupts = <0 8 1>; + interrupts = <0 8 4>; clocks = <&apb1_gates 1>; clock-frequency = <100000>; status = "disabled"; @@ -371,7 +371,7 @@ i2c2: i2c@01c2b400 { compatible = "allwinner,sun4i-i2c"; reg = <0x01c2b400 0x400>; - interrupts = <0 9 1>; + interrupts = <0 9 4>; clocks = <&apb1_gates 2>; clock-frequency = <100000>; status = "disabled"; @@ -380,7 +380,7 @@ i2c3: i2c@01c2b800 { compatible = "allwinner,sun4i-i2c"; reg = <0x01c2b800 0x400>; - interrupts = <0 88 1>; + interrupts = <0 88 4>; clocks = <&apb1_gates 3>; clock-frequency = <100000>; status = "disabled"; @@ -389,7 +389,7 @@ i2c4: i2c@01c2bc00 { compatible = "allwinner,sun4i-i2c"; reg = <0x01c2bc00 0x400>; - interrupts = <0 89 1>; + interrupts = <0 89 4>; clocks = <&apb1_gates 15>; clock-frequency = <100000>; status = "disabled"; diff --git a/arch/arm/configs/multi_v7_defconfig b/arch/arm/configs/multi_v7_defconfig index 4a5903e..c1df4e9 100644 --- a/arch/arm/configs/multi_v7_defconfig +++ b/arch/arm/configs/multi_v7_defconfig @@ -69,6 +69,7 @@ CONFIG_KS8851=y CONFIG_SMSC911X=y CONFIG_STMMAC_ETH=y CONFIG_MDIO_SUN4I=y +CONFIG_TI_CPSW=y CONFIG_KEYBOARD_SPEAR=y CONFIG_SERIO_AMBAKMI=y CONFIG_SERIAL_8250=y @@ -133,12 +134,14 @@ CONFIG_USB_GPIO_VBUS=y CONFIG_USB_ISP1301=y CONFIG_USB_MXS_PHY=y CONFIG_MMC=y +CONFIG_MMC_BLOCK_MINORS=16 CONFIG_MMC_ARMMMCI=y CONFIG_MMC_SDHCI=y CONFIG_MMC_SDHCI_PLTFM=y CONFIG_MMC_SDHCI_ESDHC_IMX=y CONFIG_MMC_SDHCI_TEGRA=y CONFIG_MMC_SDHCI_SPEAR=y +CONFIG_MMC_SDHCI_BCM_KONA=y CONFIG_MMC_OMAP=y CONFIG_MMC_OMAP_HS=y CONFIG_EDAC=y diff --git a/arch/arm/configs/omap2plus_defconfig b/arch/arm/configs/omap2plus_defconfig index 98a50c3..bfa80a1 100644 --- a/arch/arm/configs/omap2plus_defconfig +++ b/arch/arm/configs/omap2plus_defconfig @@ -173,6 +173,7 @@ CONFIG_MFD_PALMAS=y CONFIG_MFD_TPS65217=y CONFIG_MFD_TPS65910=y CONFIG_TWL6040_CORE=y +CONFIG_REGULATOR_FIXED_VOLTAGE=y CONFIG_REGULATOR_PALMAS=y CONFIG_REGULATOR_TPS65023=y CONFIG_REGULATOR_TPS6507X=y diff --git a/arch/arm/configs/sunxi_defconfig b/arch/arm/configs/sunxi_defconfig index d57a85b..3e2259b 100644 --- a/arch/arm/configs/sunxi_defconfig +++ b/arch/arm/configs/sunxi_defconfig @@ -12,6 +12,9 @@ CONFIG_NET=y CONFIG_PACKET=y CONFIG_UNIX=y CONFIG_INET=y +CONFIG_IP_PNP=y +CONFIG_IP_PNP_DHCP=y +CONFIG_IP_PNP_BOOTP=y # CONFIG_INET_XFRM_MODE_TRANSPORT is not set # CONFIG_INET_XFRM_MODE_TUNNEL is not set # CONFIG_INET_XFRM_MODE_BEET is not set @@ -58,4 +61,8 @@ CONFIG_LEDS_TRIGGER_HEARTBEAT=y CONFIG_LEDS_TRIGGER_DEFAULT_ON=y CONFIG_COMMON_CLK_DEBUG=y # CONFIG_IOMMU_SUPPORT is not set +CONFIG_TMPFS=y +CONFIG_NFS_FS=y +CONFIG_ROOT_NFS=y CONFIG_NLS=y +CONFIG_PRINTK_TIME=y diff --git a/arch/arm/configs/u8500_defconfig b/arch/arm/configs/u8500_defconfig index ac632cc..c6ebc18 100644 --- a/arch/arm/configs/u8500_defconfig +++ b/arch/arm/configs/u8500_defconfig @@ -22,6 +22,7 @@ CONFIG_CMDLINE="root=/dev/ram0 console=ttyAMA2,115200n8" CONFIG_CPU_FREQ=y CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND=y CONFIG_CPU_IDLE=y +CONFIG_ARM_U8500_CPUIDLE=y CONFIG_VFP=y CONFIG_NEON=y CONFIG_PM_RUNTIME=y @@ -109,6 +110,8 @@ CONFIG_EXT2_FS_SECURITY=y CONFIG_EXT3_FS=y CONFIG_EXT4_FS=y CONFIG_VFAT_FS=y +CONFIG_DEVTMPFS=y +CONFIG_DEVTMPFS_MOUNT=y CONFIG_TMPFS=y CONFIG_TMPFS_POSIX_ACL=y # CONFIG_MISC_FILESYSTEMS is not set diff --git a/arch/arm/crypto/aesbs-core.S_shipped b/arch/arm/crypto/aesbs-core.S_shipped index 64205d4..71e5fc7 100644 --- a/arch/arm/crypto/aesbs-core.S_shipped +++ b/arch/arm/crypto/aesbs-core.S_shipped @@ -58,7 +58,7 @@ # define VFP_ABI_FRAME 0 # define BSAES_ASM_EXTENDED_KEY # define XTS_CHAIN_TWEAK -# define __ARM_ARCH__ __LINUX_ARM_ARCH__ +# define __ARM_ARCH__ 7 #endif #ifdef __thumb__ diff --git a/arch/arm/crypto/bsaes-armv7.pl b/arch/arm/crypto/bsaes-armv7.pl index f3d96d9..be068db 100644 --- a/arch/arm/crypto/bsaes-armv7.pl +++ b/arch/arm/crypto/bsaes-armv7.pl @@ -701,7 +701,7 @@ $code.=<<___; # define VFP_ABI_FRAME 0 # define BSAES_ASM_EXTENDED_KEY # define XTS_CHAIN_TWEAK -# define __ARM_ARCH__ __LINUX_ARM_ARCH__ +# define __ARM_ARCH__ 7 #endif #ifdef __thumb__ diff --git a/arch/arm/include/asm/io.h b/arch/arm/include/asm/io.h index 3c597c2..fbeb39c 100644 --- a/arch/arm/include/asm/io.h +++ b/arch/arm/include/asm/io.h @@ -329,7 +329,7 @@ extern void _memset_io(volatile void __iomem *, int, size_t); */ #define ioremap(cookie,size) __arm_ioremap((cookie), (size), MT_DEVICE) #define ioremap_nocache(cookie,size) __arm_ioremap((cookie), (size), MT_DEVICE) -#define ioremap_cached(cookie,size) __arm_ioremap((cookie), (size), MT_DEVICE_CACHED) +#define ioremap_cache(cookie,size) __arm_ioremap((cookie), (size), MT_DEVICE_CACHED) #define ioremap_wc(cookie,size) __arm_ioremap((cookie), (size), MT_DEVICE_WC) #define iounmap __arm_iounmap diff --git a/arch/arm/include/asm/memory.h b/arch/arm/include/asm/memory.h index 9ecccc8..8756e4b 100644 --- a/arch/arm/include/asm/memory.h +++ b/arch/arm/include/asm/memory.h @@ -100,23 +100,19 @@ #define TASK_UNMAPPED_BASE UL(0x00000000) #endif -#ifndef PHYS_OFFSET -#define PHYS_OFFSET UL(CONFIG_DRAM_BASE) -#endif - #ifndef END_MEM #define END_MEM (UL(CONFIG_DRAM_BASE) + CONFIG_DRAM_SIZE) #endif #ifndef PAGE_OFFSET -#define PAGE_OFFSET (PHYS_OFFSET) +#define PAGE_OFFSET PLAT_PHYS_OFFSET #endif /* * The module can be at any place in ram in nommu mode. */ #define MODULES_END (END_MEM) -#define MODULES_VADDR (PHYS_OFFSET) +#define MODULES_VADDR PAGE_OFFSET #define XIP_VIRT_ADDR(physaddr) (physaddr) @@ -157,6 +153,16 @@ #endif #define ARCH_PGD_MASK ((1 << ARCH_PGD_SHIFT) - 1) +/* + * PLAT_PHYS_OFFSET is the offset (from zero) of the start of physical + * memory. This is used for XIP and NoMMU kernels, or by kernels which + * have their own mach/memory.h. Assembly code must always use + * PLAT_PHYS_OFFSET and not PHYS_OFFSET. + */ +#ifndef PLAT_PHYS_OFFSET +#define PLAT_PHYS_OFFSET UL(CONFIG_PHYS_OFFSET) +#endif + #ifndef __ASSEMBLY__ /* @@ -239,6 +245,8 @@ static inline unsigned long __phys_to_virt(phys_addr_t x) #else +#define PHYS_OFFSET PLAT_PHYS_OFFSET + static inline phys_addr_t __virt_to_phys(unsigned long x) { return (phys_addr_t)x - PAGE_OFFSET + PHYS_OFFSET; @@ -251,17 +259,6 @@ static inline unsigned long __phys_to_virt(phys_addr_t x) #endif #endif -#endif /* __ASSEMBLY__ */ - -#ifndef PHYS_OFFSET -#ifdef PLAT_PHYS_OFFSET -#define PHYS_OFFSET PLAT_PHYS_OFFSET -#else -#define PHYS_OFFSET UL(CONFIG_PHYS_OFFSET) -#endif -#endif - -#ifndef __ASSEMBLY__ /* * PFNs are used to describe any physical page; this means @@ -350,7 +347,8 @@ static inline __deprecated void *bus_to_virt(unsigned long x) #define ARCH_PFN_OFFSET PHYS_PFN_OFFSET #define virt_to_page(kaddr) pfn_to_page(__pa(kaddr) >> PAGE_SHIFT) -#define virt_addr_valid(kaddr) ((unsigned long)(kaddr) >= PAGE_OFFSET && (unsigned long)(kaddr) < (unsigned long)high_memory) +#define virt_addr_valid(kaddr) (((unsigned long)(kaddr) >= PAGE_OFFSET && (unsigned long)(kaddr) < (unsigned long)high_memory) \ + && pfn_valid(__pa(kaddr) >> PAGE_SHIFT) ) #endif diff --git a/arch/arm/include/asm/xen/page.h b/arch/arm/include/asm/xen/page.h index 75579a9..3759cac 100644 --- a/arch/arm/include/asm/xen/page.h +++ b/arch/arm/include/asm/xen/page.h @@ -117,6 +117,6 @@ static inline bool set_phys_to_machine(unsigned long pfn, unsigned long mfn) return __set_phys_to_machine(pfn, mfn); } -#define xen_remap(cookie, size) ioremap_cached((cookie), (size)); +#define xen_remap(cookie, size) ioremap_cache((cookie), (size)); #endif /* _ASM_ARM_XEN_PAGE_H */ diff --git a/arch/arm/kernel/head-nommu.S b/arch/arm/kernel/head-nommu.S index 14235ba..716249c 100644 --- a/arch/arm/kernel/head-nommu.S +++ b/arch/arm/kernel/head-nommu.S @@ -68,7 +68,7 @@ ENTRY(stext) #ifdef CONFIG_ARM_MPU /* Calculate the size of a region covering just the kernel */ - ldr r5, =PHYS_OFFSET @ Region start: PHYS_OFFSET + ldr r5, =PLAT_PHYS_OFFSET @ Region start: PHYS_OFFSET ldr r6, =(_end) @ Cover whole kernel sub r6, r6, r5 @ Minimum size of region to map clz r6, r6 @ Region size must be 2^N... @@ -213,7 +213,7 @@ ENTRY(__setup_mpu) set_region_nr r0, #MPU_RAM_REGION isb /* Full access from PL0, PL1, shared for CONFIG_SMP, cacheable */ - ldr r0, =PHYS_OFFSET @ RAM starts at PHYS_OFFSET + ldr r0, =PLAT_PHYS_OFFSET @ RAM starts at PHYS_OFFSET ldr r5,=(MPU_AP_PL1RW_PL0RW | MPU_RGN_NORMAL) setup_region r0, r5, r6, MPU_DATA_SIDE @ PHYS_OFFSET, shared, enabled diff --git a/arch/arm/kernel/head.S b/arch/arm/kernel/head.S index 11d59b3..32f317e 100644 --- a/arch/arm/kernel/head.S +++ b/arch/arm/kernel/head.S @@ -110,7 +110,7 @@ ENTRY(stext) sub r4, r3, r4 @ (PHYS_OFFSET - PAGE_OFFSET) add r8, r8, r4 @ PHYS_OFFSET #else - ldr r8, =PHYS_OFFSET @ always constant in this case + ldr r8, =PLAT_PHYS_OFFSET @ always constant in this case #endif /* diff --git a/arch/arm/kernel/process.c b/arch/arm/kernel/process.c index 94f6b05..92f7b15 100644 --- a/arch/arm/kernel/process.c +++ b/arch/arm/kernel/process.c @@ -404,6 +404,7 @@ EXPORT_SYMBOL(dump_fpu); unsigned long get_wchan(struct task_struct *p) { struct stackframe frame; + unsigned long stack_page; int count = 0; if (!p || p == current || p->state == TASK_RUNNING) return 0; @@ -412,9 +413,11 @@ unsigned long get_wchan(struct task_struct *p) frame.sp = thread_saved_sp(p); frame.lr = 0; /* recovered from the stack */ frame.pc = thread_saved_pc(p); + stack_page = (unsigned long)task_stack_page(p); do { - int ret = unwind_frame(&frame); - if (ret < 0) + if (frame.sp < stack_page || + frame.sp >= stack_page + THREAD_SIZE || + unwind_frame(&frame) < 0) return 0; if (!in_sched_functions(frame.pc)) return frame.pc; diff --git a/arch/arm/kernel/setup.c b/arch/arm/kernel/setup.c index 6a1b8a8..987a7f5 100644 --- a/arch/arm/kernel/setup.c +++ b/arch/arm/kernel/setup.c @@ -873,8 +873,6 @@ void __init setup_arch(char **cmdline_p) machine_desc = mdesc; machine_name = mdesc->name; - setup_dma_zone(mdesc); - if (mdesc->reboot_mode != REBOOT_HARD) reboot_mode = mdesc->reboot_mode; @@ -892,6 +890,7 @@ void __init setup_arch(char **cmdline_p) sort(&meminfo.bank, meminfo.nr_banks, sizeof(meminfo.bank[0]), meminfo_cmp, NULL); early_paging_init(mdesc, lookup_processor_type(read_cpuid_id())); + setup_dma_zone(mdesc); sanity_check_meminfo(); arm_memblock_init(&meminfo, mdesc); diff --git a/arch/arm/kernel/stacktrace.c b/arch/arm/kernel/stacktrace.c index 00f79e5..af4e8c8 100644 --- a/arch/arm/kernel/stacktrace.c +++ b/arch/arm/kernel/stacktrace.c @@ -31,7 +31,7 @@ int notrace unwind_frame(struct stackframe *frame) high = ALIGN(low, THREAD_SIZE); /* check current frame pointer is within bounds */ - if (fp < (low + 12) || fp + 4 >= high) + if (fp < low + 12 || fp > high - 4) return -EINVAL; /* restore the registers from the stack frame */ diff --git a/arch/arm/kernel/traps.c b/arch/arm/kernel/traps.c index dbf0923..6eda3bf 100644 --- a/arch/arm/kernel/traps.c +++ b/arch/arm/kernel/traps.c @@ -36,7 +36,13 @@ #include <asm/system_misc.h> #include <asm/opcodes.h> -static const char *handler[]= { "prefetch abort", "data abort", "address exception", "interrupt" }; +static const char *handler[]= { + "prefetch abort", + "data abort", + "address exception", + "interrupt", + "undefined instruction", +}; void *vectors_page; @@ -509,9 +515,10 @@ static inline int __do_cache_op(unsigned long start, unsigned long end) { int ret; - unsigned long chunk = PAGE_SIZE; do { + unsigned long chunk = min(PAGE_SIZE, end - start); + if (signal_pending(current)) { struct thread_info *ti = current_thread_info(); diff --git a/arch/arm/mach-at91/at91rm9200_time.c b/arch/arm/mach-at91/at91rm9200_time.c index f607deb..bc7b363 100644 --- a/arch/arm/mach-at91/at91rm9200_time.c +++ b/arch/arm/mach-at91/at91rm9200_time.c @@ -174,7 +174,6 @@ clkevt32k_next_event(unsigned long delta, struct clock_event_device *dev) static struct clock_event_device clkevt = { .name = "at91_tick", .features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT, - .shift = 32, .rating = 150, .set_next_event = clkevt32k_next_event, .set_mode = clkevt32k_mode, @@ -265,11 +264,9 @@ void __init at91rm9200_timer_init(void) at91_st_write(AT91_ST_RTMR, 1); /* Setup timer clockevent, with minimum of two ticks (important!!) */ - clkevt.mult = div_sc(AT91_SLOW_CLOCK, NSEC_PER_SEC, clkevt.shift); - clkevt.max_delta_ns = clockevent_delta2ns(AT91_ST_ALMV, &clkevt); - clkevt.min_delta_ns = clockevent_delta2ns(2, &clkevt) + 1; clkevt.cpumask = cpumask_of(0); - clockevents_register_device(&clkevt); + clockevents_config_and_register(&clkevt, AT91_SLOW_CLOCK, + 2, AT91_ST_ALMV); /* register clocksource */ clocksource_register_hz(&clk32k, AT91_SLOW_CLOCK); diff --git a/arch/arm/mach-at91/pm.h b/arch/arm/mach-at91/pm.h index 3ed190c..c5101dc 100644 --- a/arch/arm/mach-at91/pm.h +++ b/arch/arm/mach-at91/pm.h @@ -16,7 +16,11 @@ #include <mach/at91_ramc.h> #include <mach/at91rm9200_sdramc.h> +#ifdef CONFIG_PM extern void at91_pm_set_standby(void (*at91_standby)(void)); +#else +static inline void at91_pm_set_standby(void (*at91_standby)(void)) { } +#endif /* * The AT91RM9200 goes into self-refresh mode with this command, and will diff --git a/arch/arm/mach-at91/sama5d3.c b/arch/arm/mach-at91/sama5d3.c index 3ea8642..a28873f 100644 --- a/arch/arm/mach-at91/sama5d3.c +++ b/arch/arm/mach-at91/sama5d3.c @@ -95,19 +95,19 @@ static struct clk twi0_clk = { .name = "twi0_clk", .pid = SAMA5D3_ID_TWI0, .type = CLK_TYPE_PERIPHERAL, - .div = AT91_PMC_PCR_DIV2, + .div = AT91_PMC_PCR_DIV8, }; static struct clk twi1_clk = { .name = "twi1_clk", .pid = SAMA5D3_ID_TWI1, .type = CLK_TYPE_PERIPHERAL, - .div = AT91_PMC_PCR_DIV2, + .div = AT91_PMC_PCR_DIV8, }; static struct clk twi2_clk = { .name = "twi2_clk", .pid = SAMA5D3_ID_TWI2, .type = CLK_TYPE_PERIPHERAL, - .div = AT91_PMC_PCR_DIV2, + .div = AT91_PMC_PCR_DIV8, }; static struct clk mmc0_clk = { .name = "mci0_clk", diff --git a/arch/arm/mach-davinci/devices-da8xx.c b/arch/arm/mach-davinci/devices-da8xx.c index c46eccb..78829c5 100644 --- a/arch/arm/mach-davinci/devices-da8xx.c +++ b/arch/arm/mach-davinci/devices-da8xx.c @@ -487,7 +487,7 @@ int __init da8xx_register_emac(void) static struct resource da830_mcasp1_resources[] = { { - .name = "mcasp1", + .name = "mpu", .start = DAVINCI_DA830_MCASP1_REG_BASE, .end = DAVINCI_DA830_MCASP1_REG_BASE + (SZ_1K * 12) - 1, .flags = IORESOURCE_MEM, @@ -515,7 +515,7 @@ static struct platform_device da830_mcasp1_device = { static struct resource da850_mcasp_resources[] = { { - .name = "mcasp", + .name = "mpu", .start = DAVINCI_DA8XX_MCASP0_REG_BASE, .end = DAVINCI_DA8XX_MCASP0_REG_BASE + (SZ_1K * 12) - 1, .flags = IORESOURCE_MEM, diff --git a/arch/arm/mach-davinci/dm355.c b/arch/arm/mach-davinci/dm355.c index ef9ff1f..6117fc6 100644 --- a/arch/arm/mach-davinci/dm355.c +++ b/arch/arm/mach-davinci/dm355.c @@ -641,6 +641,7 @@ static struct platform_device dm355_edma_device = { static struct resource dm355_asp1_resources[] = { { + .name = "mpu", .start = DAVINCI_ASP1_BASE, .end = DAVINCI_ASP1_BASE + SZ_8K - 1, .flags = IORESOURCE_MEM, @@ -906,7 +907,7 @@ static struct davinci_gpio_platform_data dm355_gpio_platform_data = { int __init dm355_gpio_register(void) { return davinci_gpio_register(dm355_gpio_resources, - sizeof(dm355_gpio_resources), + ARRAY_SIZE(dm355_gpio_resources), &dm355_gpio_platform_data); } /*----------------------------------------------------------------------*/ diff --git a/arch/arm/mach-davinci/dm365.c b/arch/arm/mach-davinci/dm365.c index 1511a06..d7c6f85 100644 --- a/arch/arm/mach-davinci/dm365.c +++ b/arch/arm/mach-davinci/dm365.c @@ -720,7 +720,7 @@ static struct davinci_gpio_platform_data dm365_gpio_platform_data = { int __init dm365_gpio_register(void) { return davinci_gpio_register(dm365_gpio_resources, - sizeof(dm365_gpio_resources), + ARRAY_SIZE(dm365_gpio_resources), &dm365_gpio_platform_data); } @@ -942,6 +942,7 @@ static struct platform_device dm365_edma_device = { static struct resource dm365_asp_resources[] = { { + .name = "mpu", .start = DAVINCI_DM365_ASP0_BASE, .end = DAVINCI_DM365_ASP0_BASE + SZ_8K - 1, .flags = IORESOURCE_MEM, diff --git a/arch/arm/mach-davinci/dm644x.c b/arch/arm/mach-davinci/dm644x.c index 143a321..3ce4799 100644 --- a/arch/arm/mach-davinci/dm644x.c +++ b/arch/arm/mach-davinci/dm644x.c @@ -572,6 +572,7 @@ static struct platform_device dm644x_edma_device = { /* DM6446 EVM uses ASP0; line-out is a pair of RCA jacks */ static struct resource dm644x_asp_resources[] = { { + .name = "mpu", .start = DAVINCI_ASP0_BASE, .end = DAVINCI_ASP0_BASE + SZ_8K - 1, .flags = IORESOURCE_MEM, @@ -792,7 +793,7 @@ static struct davinci_gpio_platform_data dm644_gpio_platform_data = { int __init dm644x_gpio_register(void) { return davinci_gpio_register(dm644_gpio_resources, - sizeof(dm644_gpio_resources), + ARRAY_SIZE(dm644_gpio_resources), &dm644_gpio_platform_data); } /*----------------------------------------------------------------------*/ diff --git a/arch/arm/mach-davinci/dm646x.c b/arch/arm/mach-davinci/dm646x.c index 2a73f29..0e81fea65 100644 --- a/arch/arm/mach-davinci/dm646x.c +++ b/arch/arm/mach-davinci/dm646x.c @@ -621,7 +621,7 @@ static struct platform_device dm646x_edma_device = { static struct resource dm646x_mcasp0_resources[] = { { - .name = "mcasp0", + .name = "mpu", .start = DAVINCI_DM646X_MCASP0_REG_BASE, .end = DAVINCI_DM646X_MCASP0_REG_BASE + (SZ_1K << 1) - 1, .flags = IORESOURCE_MEM, @@ -641,7 +641,7 @@ static struct resource dm646x_mcasp0_resources[] = { static struct resource dm646x_mcasp1_resources[] = { { - .name = "mcasp1", + .name = "mpu", .start = DAVINCI_DM646X_MCASP1_REG_BASE, .end = DAVINCI_DM646X_MCASP1_REG_BASE + (SZ_1K << 1) - 1, .flags = IORESOURCE_MEM, @@ -769,7 +769,7 @@ static struct davinci_gpio_platform_data dm646x_gpio_platform_data = { int __init dm646x_gpio_register(void) { return davinci_gpio_register(dm646x_gpio_resources, - sizeof(dm646x_gpio_resources), + ARRAY_SIZE(dm646x_gpio_resources), &dm646x_gpio_platform_data); } /*----------------------------------------------------------------------*/ diff --git a/arch/arm/mach-footbridge/dc21285-timer.c b/arch/arm/mach-footbridge/dc21285-timer.c index 9ee78f7..782f6c7 100644 --- a/arch/arm/mach-footbridge/dc21285-timer.c +++ b/arch/arm/mach-footbridge/dc21285-timer.c @@ -96,11 +96,12 @@ static struct irqaction footbridge_timer_irq = { void __init footbridge_timer_init(void) { struct clock_event_device *ce = &ckevt_dc21285; + unsigned rate = DIV_ROUND_CLOSEST(mem_fclk_21285, 16); - clocksource_register_hz(&cksrc_dc21285, (mem_fclk_21285 + 8) / 16); + clocksource_register_hz(&cksrc_dc21285, rate); setup_irq(ce->irq, &footbridge_timer_irq); ce->cpumask = cpumask_of(smp_processor_id()); - clockevents_config_and_register(ce, mem_fclk_21285, 0x4, 0xffffff); + clockevents_config_and_register(ce, rate, 0x4, 0xffffff); } diff --git a/arch/arm/mach-highbank/highbank.c b/arch/arm/mach-highbank/highbank.c index b3d7e56..bd3bf66 100644 --- a/arch/arm/mach-highbank/highbank.c +++ b/arch/arm/mach-highbank/highbank.c @@ -17,12 +17,15 @@ #include <linux/clkdev.h> #include <linux/clocksource.h> #include <linux/dma-mapping.h> +#include <linux/input.h> #include <linux/io.h> #include <linux/irqchip.h> +#include <linux/mailbox.h> #include <linux/of.h> #include <linux/of_irq.h> #include <linux/of_platform.h> #include <linux/of_address.h> +#include <linux/reboot.h> #include <linux/amba/bus.h> #include <linux/platform_device.h> @@ -130,6 +133,24 @@ static struct platform_device highbank_cpuidle_device = { .name = "cpuidle-calxeda", }; +static int hb_keys_notifier(struct notifier_block *nb, unsigned long event, void *data) +{ + u32 key = *(u32 *)data; + + if (event != 0x1000) + return 0; + + if (key == KEY_POWER) + orderly_poweroff(false); + else if (key == 0xffff) + ctrl_alt_del(); + + return 0; +} +static struct notifier_block hb_keys_nb = { + .notifier_call = hb_keys_notifier, +}; + static void __init highbank_init(void) { struct device_node *np; @@ -145,6 +166,8 @@ static void __init highbank_init(void) bus_register_notifier(&platform_bus_type, &highbank_platform_nb); bus_register_notifier(&amba_bustype, &highbank_amba_nb); + pl320_ipc_register_notifier(&hb_keys_nb); + of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL); if (psci_ops.cpu_suspend) diff --git a/arch/arm/mach-omap2/board-generic.c b/arch/arm/mach-omap2/board-generic.c index 19f1652..8d972ff1 100644 --- a/arch/arm/mach-omap2/board-generic.c +++ b/arch/arm/mach-omap2/board-generic.c @@ -131,6 +131,24 @@ DT_MACHINE_START(OMAP3_GP_DT, "Generic OMAP3-GP (Flattened Device Tree)") .dt_compat = omap3_gp_boards_compat, .restart = omap3xxx_restart, MACHINE_END + +static const char *am3517_boards_compat[] __initdata = { + "ti,am3517", + NULL, +}; + +DT_MACHINE_START(AM3517_DT, "Generic AM3517 (Flattened Device Tree)") + .reserve = omap_reserve, + .map_io = omap3_map_io, + .init_early = am35xx_init_early, + .init_irq = omap_intc_of_init, + .handle_irq = omap3_intc_handle_irq, + .init_machine = omap_generic_init, + .init_late = omap3_init_late, + .init_time = omap3_gptimer_timer_init, + .dt_compat = am3517_boards_compat, + .restart = omap3xxx_restart, +MACHINE_END #endif #ifdef CONFIG_SOC_AM33XX diff --git a/arch/arm/mach-omap2/board-ldp.c b/arch/arm/mach-omap2/board-ldp.c index 4ec8d82..44a59c3 100644 --- a/arch/arm/mach-omap2/board-ldp.c +++ b/arch/arm/mach-omap2/board-ldp.c @@ -242,12 +242,18 @@ static void __init ldp_display_init(void) static int ldp_twl_gpio_setup(struct device *dev, unsigned gpio, unsigned ngpio) { + int res; + /* LCD enable GPIO */ ldp_lcd_pdata.enable_gpio = gpio + 7; /* Backlight enable GPIO */ ldp_lcd_pdata.backlight_gpio = gpio + 15; + res = platform_device_register(&ldp_lcd_device); + if (res) + pr_err("Unable to register LCD: %d\n", res); + return 0; } @@ -346,7 +352,6 @@ static struct omap2_hsmmc_info mmc[] __initdata = { static struct platform_device *ldp_devices[] __initdata = { &ldp_gpio_keys_device, - &ldp_lcd_device, }; #ifdef CONFIG_OMAP_MUX diff --git a/arch/arm/mach-omap2/display.c b/arch/arm/mach-omap2/display.c index 58347bb..4cf1655 100644 --- a/arch/arm/mach-omap2/display.c +++ b/arch/arm/mach-omap2/display.c @@ -101,13 +101,51 @@ static const struct omap_dss_hwmod_data omap4_dss_hwmod_data[] __initconst = { { "dss_hdmi", "omapdss_hdmi", -1 }, }; +static int omap4_dsi_mux_pads(int dsi_id, unsigned lanes) +{ + u32 enable_mask, enable_shift; + u32 pipd_mask, pipd_shift; + u32 reg; + + if (dsi_id == 0) { + enable_mask = OMAP4_DSI1_LANEENABLE_MASK; + enable_shift = OMAP4_DSI1_LANEENABLE_SHIFT; + pipd_mask = OMAP4_DSI1_PIPD_MASK; + pipd_shift = OMAP4_DSI1_PIPD_SHIFT; + } else if (dsi_id == 1) { + enable_mask = OMAP4_DSI2_LANEENABLE_MASK; + enable_shift = OMAP4_DSI2_LANEENABLE_SHIFT; + pipd_mask = OMAP4_DSI2_PIPD_MASK; + pipd_shift = OMAP4_DSI2_PIPD_SHIFT; + } else { + return -ENODEV; + } + + reg = omap4_ctrl_pad_readl(OMAP4_CTRL_MODULE_PAD_CORE_CONTROL_DSIPHY); + + reg &= ~enable_mask; + reg &= ~pipd_mask; + + reg |= (lanes << enable_shift) & enable_mask; + reg |= (lanes << pipd_shift) & pipd_mask; + + omap4_ctrl_pad_writel(reg, OMAP4_CTRL_MODULE_PAD_CORE_CONTROL_DSIPHY); + + return 0; +} + static int omap_dsi_enable_pads(int dsi_id, unsigned lane_mask) { + if (cpu_is_omap44xx()) + return omap4_dsi_mux_pads(dsi_id, lane_mask); + return 0; } static void omap_dsi_disable_pads(int dsi_id, unsigned lane_mask) { + if (cpu_is_omap44xx()) + omap4_dsi_mux_pads(dsi_id, 0); } static int omap_dss_set_min_bus_tput(struct device *dev, unsigned long tput) diff --git a/arch/arm/mach-omap2/dss-common.c b/arch/arm/mach-omap2/dss-common.c index 365bfd3..dadccc9 100644 --- a/arch/arm/mach-omap2/dss-common.c +++ b/arch/arm/mach-omap2/dss-common.c @@ -223,7 +223,7 @@ void __init omap_4430sdp_display_init_of(void) static struct connector_dvi_platform_data omap3_igep2_dvi_connector_pdata = { .name = "dvi", .source = "tfp410.0", - .i2c_bus_num = 3, + .i2c_bus_num = 2, }; static struct platform_device omap3_igep2_dvi_connector_device = { diff --git a/arch/arm/mach-omap2/omap_device.c b/arch/arm/mach-omap2/omap_device.c index 53f0735..e0a398c 100644 --- a/arch/arm/mach-omap2/omap_device.c +++ b/arch/arm/mach-omap2/omap_device.c @@ -183,6 +183,10 @@ static int omap_device_build_from_dt(struct platform_device *pdev) odbfd_exit1: kfree(hwmods); odbfd_exit: + /* if data/we are at fault.. load up a fail handler */ + if (ret) + pdev->dev.pm_domain = &omap_device_fail_pm_domain; + return ret; } @@ -604,6 +608,19 @@ static int _od_runtime_resume(struct device *dev) return pm_generic_runtime_resume(dev); } + +static int _od_fail_runtime_suspend(struct device *dev) +{ + dev_warn(dev, "%s: FIXME: missing hwmod/omap_dev info\n", __func__); + return -ENODEV; +} + +static int _od_fail_runtime_resume(struct device *dev) +{ + dev_warn(dev, "%s: FIXME: missing hwmod/omap_dev info\n", __func__); + return -ENODEV; +} + #endif #ifdef CONFIG_SUSPEND @@ -657,6 +674,13 @@ static int _od_resume_noirq(struct device *dev) #define _od_resume_noirq NULL #endif +struct dev_pm_domain omap_device_fail_pm_domain = { + .ops = { + SET_RUNTIME_PM_OPS(_od_fail_runtime_suspend, + _od_fail_runtime_resume, NULL) + } +}; + struct dev_pm_domain omap_device_pm_domain = { .ops = { SET_RUNTIME_PM_OPS(_od_runtime_suspend, _od_runtime_resume, diff --git a/arch/arm/mach-omap2/omap_device.h b/arch/arm/mach-omap2/omap_device.h index 17ca1ae..78c02b3 100644 --- a/arch/arm/mach-omap2/omap_device.h +++ b/arch/arm/mach-omap2/omap_device.h @@ -29,6 +29,7 @@ #include "omap_hwmod.h" extern struct dev_pm_domain omap_device_pm_domain; +extern struct dev_pm_domain omap_device_fail_pm_domain; /* omap_device._state values */ #define OMAP_DEVICE_STATE_UNKNOWN 0 diff --git a/arch/arm/mach-omap2/omap_hwmod.c b/arch/arm/mach-omap2/omap_hwmod.c index e3f0eca..8a1b5e0 100644 --- a/arch/arm/mach-omap2/omap_hwmod.c +++ b/arch/arm/mach-omap2/omap_hwmod.c @@ -399,7 +399,7 @@ static int _set_clockactivity(struct omap_hwmod *oh, u8 clockact, u32 *v) } /** - * _set_softreset: set OCP_SYSCONFIG.CLOCKACTIVITY bits in @v + * _set_softreset: set OCP_SYSCONFIG.SOFTRESET bit in @v * @oh: struct omap_hwmod * * @v: pointer to register contents to modify * @@ -427,6 +427,36 @@ static int _set_softreset(struct omap_hwmod *oh, u32 *v) } /** + * _clear_softreset: clear OCP_SYSCONFIG.SOFTRESET bit in @v + * @oh: struct omap_hwmod * + * @v: pointer to register contents to modify + * + * Clear the SOFTRESET bit in @v for hwmod @oh. Returns -EINVAL upon + * error or 0 upon success. + */ +static int _clear_softreset(struct omap_hwmod *oh, u32 *v) +{ + u32 softrst_mask; + + if (!oh->class->sysc || + !(oh->class->sysc->sysc_flags & SYSC_HAS_SOFTRESET)) + return -EINVAL; + + if (!oh->class->sysc->sysc_fields) { + WARN(1, + "omap_hwmod: %s: sysc_fields absent for sysconfig class\n", + oh->name); + return -EINVAL; + } + + softrst_mask = (0x1 << oh->class->sysc->sysc_fields->srst_shift); + + *v &= ~softrst_mask; + + return 0; +} + +/** * _wait_softreset_complete - wait for an OCP softreset to complete * @oh: struct omap_hwmod * to wait on * @@ -785,6 +815,7 @@ static int _init_interface_clks(struct omap_hwmod *oh) pr_warning("omap_hwmod: %s: cannot clk_get interface_clk %s\n", oh->name, os->clk); ret = -EINVAL; + continue; } os->_clk = c; /* @@ -821,6 +852,7 @@ static int _init_opt_clks(struct omap_hwmod *oh) pr_warning("omap_hwmod: %s: cannot clk_get opt_clk %s\n", oh->name, oc->clk); ret = -EINVAL; + continue; } oc->_clk = c; /* @@ -1911,6 +1943,12 @@ static int _ocp_softreset(struct omap_hwmod *oh) ret = _set_softreset(oh, &v); if (ret) goto dis_opt_clks; + + _write_sysconfig(v, oh); + ret = _clear_softreset(oh, &v); + if (ret) + goto dis_opt_clks; + _write_sysconfig(v, oh); if (oh->class->sysc->srst_udelay) @@ -2326,38 +2364,80 @@ static int _shutdown(struct omap_hwmod *oh) return 0; } +static int of_dev_find_hwmod(struct device_node *np, + struct omap_hwmod *oh) +{ + int count, i, res; + const char *p; + + count = of_property_count_strings(np, "ti,hwmods"); + if (count < 1) + return -ENODEV; + + for (i = 0; i < count; i++) { + res = of_property_read_string_index(np, "ti,hwmods", + i, &p); + if (res) + continue; + if (!strcmp(p, oh->name)) { + pr_debug("omap_hwmod: dt %s[%i] uses hwmod %s\n", + np->name, i, oh->name); + return i; + } + } + + return -ENODEV; +} + /** * of_dev_hwmod_lookup - look up needed hwmod from dt blob * @np: struct device_node * * @oh: struct omap_hwmod * + * @index: index of the entry found + * @found: struct device_node * found or NULL * * Parse the dt blob and find out needed hwmod. Recursive function is * implemented to take care hierarchical dt blob parsing. - * Return: The device node on success or NULL on failure. + * Return: Returns 0 on success, -ENODEV when not found. */ -static struct device_node *of_dev_hwmod_lookup(struct device_node *np, - struct omap_hwmod *oh) +static int of_dev_hwmod_lookup(struct device_node *np, + struct omap_hwmod *oh, + int *index, + struct device_node **found) { - struct device_node *np0 = NULL, *np1 = NULL; - const char *p; + struct device_node *np0 = NULL; + int res; + + res = of_dev_find_hwmod(np, oh); + if (res >= 0) { + *found = np; + *index = res; + return 0; + } for_each_child_of_node(np, np0) { - if (of_find_property(np0, "ti,hwmods", NULL)) { - p = of_get_property(np0, "ti,hwmods", NULL); - if (!strcmp(p, oh->name)) - return np0; - np1 = of_dev_hwmod_lookup(np0, oh); - if (np1) - return np1; + struct device_node *fc; + int i; + + res = of_dev_hwmod_lookup(np0, oh, &i, &fc); + if (res == 0) { + *found = fc; + *index = i; + return 0; } } - return NULL; + + *found = NULL; + *index = 0; + + return -ENODEV; } /** * _init_mpu_rt_base - populate the virtual address for a hwmod * @oh: struct omap_hwmod * to locate the virtual address * @data: (unused, caller should pass NULL) + * @index: index of the reg entry iospace in device tree * @np: struct device_node * of the IP block's device node in the DT data * * Cache the virtual address used by the MPU to access this IP block's @@ -2368,7 +2448,7 @@ static struct device_node *of_dev_hwmod_lookup(struct device_node *np, * -ENXIO on absent or invalid register target address space. */ static int __init _init_mpu_rt_base(struct omap_hwmod *oh, void *data, - struct device_node *np) + int index, struct device_node *np) { struct omap_hwmod_addr_space *mem; void __iomem *va_start = NULL; @@ -2390,13 +2470,17 @@ static int __init _init_mpu_rt_base(struct omap_hwmod *oh, void *data, if (!np) return -ENXIO; - va_start = of_iomap(np, oh->mpu_rt_idx); + va_start = of_iomap(np, index + oh->mpu_rt_idx); } else { va_start = ioremap(mem->pa_start, mem->pa_end - mem->pa_start); } if (!va_start) { - pr_err("omap_hwmod: %s: Could not ioremap\n", oh->name); + if (mem) + pr_err("omap_hwmod: %s: Could not ioremap\n", oh->name); + else + pr_err("omap_hwmod: %s: Missing dt reg%i for %s\n", + oh->name, index, np->full_name); return -ENXIO; } @@ -2422,17 +2506,29 @@ static int __init _init_mpu_rt_base(struct omap_hwmod *oh, void *data, */ static int __init _init(struct omap_hwmod *oh, void *data) { - int r; + int r, index; struct device_node *np = NULL; if (oh->_state != _HWMOD_STATE_REGISTERED) return 0; - if (of_have_populated_dt()) - np = of_dev_hwmod_lookup(of_find_node_by_name(NULL, "ocp"), oh); + if (of_have_populated_dt()) { + struct device_node *bus; + + bus = of_find_node_by_name(NULL, "ocp"); + if (!bus) + return -ENODEV; + + r = of_dev_hwmod_lookup(bus, oh, &index, &np); + if (r) + pr_debug("omap_hwmod: %s missing dt data\n", oh->name); + else if (np && index) + pr_warn("omap_hwmod: %s using broken dt data from %s\n", + oh->name, np->name); + } if (oh->class->sysc) { - r = _init_mpu_rt_base(oh, NULL, np); + r = _init_mpu_rt_base(oh, NULL, index, np); if (r < 0) { WARN(1, "omap_hwmod: %s: doesn't have mpu register target base\n", oh->name); @@ -3169,6 +3265,11 @@ int omap_hwmod_softreset(struct omap_hwmod *oh) goto error; _write_sysconfig(v, oh); + ret = _clear_softreset(oh, &v); + if (ret) + goto error; + _write_sysconfig(v, oh); + error: return ret; } diff --git a/arch/arm/mach-omap2/omap_hwmod_2xxx_ipblock_data.c b/arch/arm/mach-omap2/omap_hwmod_2xxx_ipblock_data.c index 56cebb0..d23c77f 100644 --- a/arch/arm/mach-omap2/omap_hwmod_2xxx_ipblock_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_2xxx_ipblock_data.c @@ -796,7 +796,7 @@ struct omap_hwmod omap2xxx_counter_32k_hwmod = { /* gpmc */ static struct omap_hwmod_irq_info omap2xxx_gpmc_irqs[] = { - { .irq = 20 }, + { .irq = 20 + OMAP_INTC_START, }, { .irq = -1 } }; @@ -841,7 +841,7 @@ static struct omap_hwmod_class omap2_rng_hwmod_class = { }; static struct omap_hwmod_irq_info omap2_rng_mpu_irqs[] = { - { .irq = 52 }, + { .irq = 52 + OMAP_INTC_START, }, { .irq = -1 } }; diff --git a/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c b/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c index 9e56fab..4c3b1e6 100644 --- a/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c @@ -1943,7 +1943,8 @@ static struct omap_hwmod_class_sysconfig omap3xxx_usb_host_hs_sysc = { .syss_offs = 0x0014, .sysc_flags = (SYSC_HAS_MIDLEMODE | SYSC_HAS_CLOCKACTIVITY | SYSC_HAS_SIDLEMODE | SYSC_HAS_ENAWAKEUP | - SYSC_HAS_SOFTRESET | SYSC_HAS_AUTOIDLE), + SYSC_HAS_SOFTRESET | SYSC_HAS_AUTOIDLE | + SYSS_HAS_RESET_STATUS), .idlemodes = (SIDLE_FORCE | SIDLE_NO | SIDLE_SMART | MSTANDBY_FORCE | MSTANDBY_NO | MSTANDBY_SMART), .sysc_fields = &omap_hwmod_sysc_type1, @@ -2021,15 +2022,7 @@ static struct omap_hwmod omap3xxx_usb_host_hs_hwmod = { * hence HWMOD_SWSUP_MSTANDBY */ - /* - * During system boot; If the hwmod framework resets the module - * the module will have smart idle settings; which can lead to deadlock - * (above Errata Id:i660); so, dont reset the module during boot; - * Use HWMOD_INIT_NO_RESET. - */ - - .flags = HWMOD_SWSUP_SIDLE | HWMOD_SWSUP_MSTANDBY | - HWMOD_INIT_NO_RESET, + .flags = HWMOD_SWSUP_SIDLE | HWMOD_SWSUP_MSTANDBY, }; /* @@ -2172,7 +2165,7 @@ static struct omap_hwmod_class omap3xxx_gpmc_hwmod_class = { }; static struct omap_hwmod_irq_info omap3xxx_gpmc_irqs[] = { - { .irq = 20 }, + { .irq = 20 + OMAP_INTC_START, }, { .irq = -1 } }; @@ -3006,7 +2999,7 @@ static struct omap_mmu_dev_attr mmu_isp_dev_attr = { static struct omap_hwmod omap3xxx_mmu_isp_hwmod; static struct omap_hwmod_irq_info omap3xxx_mmu_isp_irqs[] = { - { .irq = 24 }, + { .irq = 24 + OMAP_INTC_START, }, { .irq = -1 } }; @@ -3048,7 +3041,7 @@ static struct omap_mmu_dev_attr mmu_iva_dev_attr = { static struct omap_hwmod omap3xxx_mmu_iva_hwmod; static struct omap_hwmod_irq_info omap3xxx_mmu_iva_irqs[] = { - { .irq = 28 }, + { .irq = 28 + OMAP_INTC_START, }, { .irq = -1 } }; diff --git a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c index 1e5b12c..3318cae9 100644 --- a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c @@ -2937,7 +2937,7 @@ static struct omap_hwmod_class_sysconfig omap44xx_usb_host_hs_sysc = { .sysc_offs = 0x0010, .syss_offs = 0x0014, .sysc_flags = (SYSC_HAS_MIDLEMODE | SYSC_HAS_SIDLEMODE | - SYSC_HAS_SOFTRESET), + SYSC_HAS_SOFTRESET | SYSC_HAS_RESET_STATUS), .idlemodes = (SIDLE_FORCE | SIDLE_NO | SIDLE_SMART | SIDLE_SMART_WKUP | MSTANDBY_FORCE | MSTANDBY_NO | MSTANDBY_SMART | MSTANDBY_SMART_WKUP), @@ -3001,15 +3001,7 @@ static struct omap_hwmod omap44xx_usb_host_hs_hwmod = { * hence HWMOD_SWSUP_MSTANDBY */ - /* - * During system boot; If the hwmod framework resets the module - * the module will have smart idle settings; which can lead to deadlock - * (above Errata Id:i660); so, dont reset the module during boot; - * Use HWMOD_INIT_NO_RESET. - */ - - .flags = HWMOD_SWSUP_SIDLE | HWMOD_SWSUP_MSTANDBY | - HWMOD_INIT_NO_RESET, + .flags = HWMOD_SWSUP_SIDLE | HWMOD_SWSUP_MSTANDBY, }; /* diff --git a/arch/arm/mach-omap2/omap_hwmod_54xx_data.c b/arch/arm/mach-omap2/omap_hwmod_54xx_data.c index 9e08d699..e297d62 100644 --- a/arch/arm/mach-omap2/omap_hwmod_54xx_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_54xx_data.c @@ -1544,7 +1544,8 @@ static struct omap_hwmod_class_sysconfig omap54xx_usb_host_hs_sysc = { .rev_offs = 0x0000, .sysc_offs = 0x0010, .sysc_flags = (SYSC_HAS_MIDLEMODE | SYSC_HAS_RESET_STATUS | - SYSC_HAS_SIDLEMODE | SYSC_HAS_SOFTRESET), + SYSC_HAS_SIDLEMODE | SYSC_HAS_SOFTRESET | + SYSC_HAS_RESET_STATUS), .idlemodes = (SIDLE_FORCE | SIDLE_NO | SIDLE_SMART | SIDLE_SMART_WKUP | MSTANDBY_FORCE | MSTANDBY_NO | MSTANDBY_SMART | MSTANDBY_SMART_WKUP), @@ -1598,15 +1599,7 @@ static struct omap_hwmod omap54xx_usb_host_hs_hwmod = { * hence HWMOD_SWSUP_MSTANDBY */ - /* - * During system boot; If the hwmod framework resets the module - * the module will have smart idle settings; which can lead to deadlock - * (above Errata Id:i660); so, dont reset the module during boot; - * Use HWMOD_INIT_NO_RESET. - */ - - .flags = HWMOD_SWSUP_SIDLE | HWMOD_SWSUP_MSTANDBY | - HWMOD_INIT_NO_RESET, + .flags = HWMOD_SWSUP_SIDLE | HWMOD_SWSUP_MSTANDBY, .main_clk = "l3init_60m_fclk", .prcm = { .omap4 = { diff --git a/arch/arm/mach-omap2/omap_hwmod_7xx_data.c b/arch/arm/mach-omap2/omap_hwmod_7xx_data.c index db32d53..18f333c 100644 --- a/arch/arm/mach-omap2/omap_hwmod_7xx_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_7xx_data.c @@ -1637,7 +1637,7 @@ static struct omap_hwmod dra7xx_uart1_hwmod = { .class = &dra7xx_uart_hwmod_class, .clkdm_name = "l4per_clkdm", .main_clk = "uart1_gfclk_mux", - .flags = HWMOD_SWSUP_SIDLE_ACT, + .flags = HWMOD_SWSUP_SIDLE_ACT | DEBUG_OMAP2UART1_FLAGS, .prcm = { .omap4 = { .clkctrl_offs = DRA7XX_CM_L4PER_UART1_CLKCTRL_OFFSET, diff --git a/arch/arm/mach-omap2/pdata-quirks.c b/arch/arm/mach-omap2/pdata-quirks.c index 10c7145..39f020c 100644 --- a/arch/arm/mach-omap2/pdata-quirks.c +++ b/arch/arm/mach-omap2/pdata-quirks.c @@ -139,6 +139,7 @@ struct of_dev_auxdata omap_auxdata_lookup[] __initdata = { static struct pdata_init pdata_quirks[] __initdata = { #ifdef CONFIG_ARCH_OMAP3 + { "nokia,omap3-n900", hsmmc2_internal_input_clk, }, { "nokia,omap3-n9", hsmmc2_internal_input_clk, }, { "nokia,omap3-n950", hsmmc2_internal_input_clk, }, { "isee,omap3-igep0020", omap3_igep0020_legacy_init, }, diff --git a/arch/arm/mach-omap2/powerdomain.c b/arch/arm/mach-omap2/powerdomain.c index e233dfc..93a2a6e 100644 --- a/arch/arm/mach-omap2/powerdomain.c +++ b/arch/arm/mach-omap2/powerdomain.c @@ -128,7 +128,8 @@ skip_voltdm: for (i = 0; i < pwrdm->banks; i++) pwrdm->ret_mem_off_counter[i] = 0; - arch_pwrdm->pwrdm_wait_transition(pwrdm); + if (arch_pwrdm && arch_pwrdm->pwrdm_wait_transition) + arch_pwrdm->pwrdm_wait_transition(pwrdm); pwrdm->state = pwrdm_read_pwrst(pwrdm); pwrdm->state_counter[pwrdm->state] = 1; diff --git a/arch/arm/mach-pxa/include/mach/lubbock.h b/arch/arm/mach-pxa/include/mach/lubbock.h index 2a086e8..958cd6af 100644 --- a/arch/arm/mach-pxa/include/mach/lubbock.h +++ b/arch/arm/mach-pxa/include/mach/lubbock.h @@ -10,6 +10,8 @@ * published by the Free Software Foundation. */ +#include <mach/irqs.h> + #define LUBBOCK_ETH_PHYS PXA_CS3_PHYS #define LUBBOCK_FPGA_PHYS PXA_CS2_PHYS diff --git a/arch/arm/mach-pxa/reset.c b/arch/arm/mach-pxa/reset.c index 0d5dd64..263b152 100644 --- a/arch/arm/mach-pxa/reset.c +++ b/arch/arm/mach-pxa/reset.c @@ -13,6 +13,7 @@ #include <mach/regs-ost.h> #include <mach/reset.h> +#include <mach/smemc.h> unsigned int reset_status; EXPORT_SYMBOL(reset_status); @@ -81,6 +82,12 @@ static void do_hw_reset(void) writel_relaxed(OSSR_M3, OSSR); /* ... in 100 ms */ writel_relaxed(readl_relaxed(OSCR) + 368640, OSMR3); + /* + * SDRAM hangs on watchdog reset on Marvell PXA270 (erratum 71) + * we put SDRAM into self-refresh to prevent that + */ + while (1) + writel_relaxed(MDREFR_SLFRSH, MDREFR); } void pxa_restart(enum reboot_mode mode, const char *cmd) @@ -104,4 +111,3 @@ void pxa_restart(enum reboot_mode mode, const char *cmd) break; } } - diff --git a/arch/arm/mach-pxa/tosa.c b/arch/arm/mach-pxa/tosa.c index 0206b91..ef5557b 100644 --- a/arch/arm/mach-pxa/tosa.c +++ b/arch/arm/mach-pxa/tosa.c @@ -425,57 +425,57 @@ static struct platform_device tosa_power_device = { * Tosa Keyboard */ static const uint32_t tosakbd_keymap[] = { - KEY(0, 2, KEY_W), - KEY(0, 6, KEY_K), - KEY(0, 7, KEY_BACKSPACE), - KEY(0, 8, KEY_P), - KEY(1, 1, KEY_Q), - KEY(1, 2, KEY_E), - KEY(1, 3, KEY_T), - KEY(1, 4, KEY_Y), - KEY(1, 6, KEY_O), - KEY(1, 7, KEY_I), - KEY(1, 8, KEY_COMMA), - KEY(2, 1, KEY_A), - KEY(2, 2, KEY_D), - KEY(2, 3, KEY_G), - KEY(2, 4, KEY_U), - KEY(2, 6, KEY_L), - KEY(2, 7, KEY_ENTER), - KEY(2, 8, KEY_DOT), - KEY(3, 1, KEY_Z), - KEY(3, 2, KEY_C), - KEY(3, 3, KEY_V), - KEY(3, 4, KEY_J), - KEY(3, 5, TOSA_KEY_ADDRESSBOOK), - KEY(3, 6, TOSA_KEY_CANCEL), - KEY(3, 7, TOSA_KEY_CENTER), - KEY(3, 8, TOSA_KEY_OK), - KEY(3, 9, KEY_LEFTSHIFT), - KEY(4, 1, KEY_S), - KEY(4, 2, KEY_R), - KEY(4, 3, KEY_B), - KEY(4, 4, KEY_N), - KEY(4, 5, TOSA_KEY_CALENDAR), - KEY(4, 6, TOSA_KEY_HOMEPAGE), - KEY(4, 7, KEY_LEFTCTRL), - KEY(4, 8, TOSA_KEY_LIGHT), - KEY(4, 10, KEY_RIGHTSHIFT), - KEY(5, 1, KEY_TAB), - KEY(5, 2, KEY_SLASH), - KEY(5, 3, KEY_H), - KEY(5, 4, KEY_M), - KEY(5, 5, TOSA_KEY_MENU), - KEY(5, 7, KEY_UP), - KEY(5, 11, TOSA_KEY_FN), - KEY(6, 1, KEY_X), - KEY(6, 2, KEY_F), - KEY(6, 3, KEY_SPACE), - KEY(6, 4, KEY_APOSTROPHE), - KEY(6, 5, TOSA_KEY_MAIL), - KEY(6, 6, KEY_LEFT), - KEY(6, 7, KEY_DOWN), - KEY(6, 8, KEY_RIGHT), + KEY(0, 1, KEY_W), + KEY(0, 5, KEY_K), + KEY(0, 6, KEY_BACKSPACE), + KEY(0, 7, KEY_P), + KEY(1, 0, KEY_Q), + KEY(1, 1, KEY_E), + KEY(1, 2, KEY_T), + KEY(1, 3, KEY_Y), + KEY(1, 5, KEY_O), + KEY(1, 6, KEY_I), + KEY(1, 7, KEY_COMMA), + KEY(2, 0, KEY_A), + KEY(2, 1, KEY_D), + KEY(2, 2, KEY_G), + KEY(2, 3, KEY_U), + KEY(2, 5, KEY_L), + KEY(2, 6, KEY_ENTER), + KEY(2, 7, KEY_DOT), + KEY(3, 0, KEY_Z), + KEY(3, 1, KEY_C), + KEY(3, 2, KEY_V), + KEY(3, 3, KEY_J), + KEY(3, 4, TOSA_KEY_ADDRESSBOOK), + KEY(3, 5, TOSA_KEY_CANCEL), + KEY(3, 6, TOSA_KEY_CENTER), + KEY(3, 7, TOSA_KEY_OK), + KEY(3, 8, KEY_LEFTSHIFT), + KEY(4, 0, KEY_S), + KEY(4, 1, KEY_R), + KEY(4, 2, KEY_B), + KEY(4, 3, KEY_N), + KEY(4, 4, TOSA_KEY_CALENDAR), + KEY(4, 5, TOSA_KEY_HOMEPAGE), + KEY(4, 6, KEY_LEFTCTRL), + KEY(4, 7, TOSA_KEY_LIGHT), + KEY(4, 9, KEY_RIGHTSHIFT), + KEY(5, 0, KEY_TAB), + KEY(5, 1, KEY_SLASH), + KEY(5, 2, KEY_H), + KEY(5, 3, KEY_M), + KEY(5, 4, TOSA_KEY_MENU), + KEY(5, 6, KEY_UP), + KEY(5, 10, TOSA_KEY_FN), + KEY(6, 0, KEY_X), + KEY(6, 1, KEY_F), + KEY(6, 2, KEY_SPACE), + KEY(6, 3, KEY_APOSTROPHE), + KEY(6, 4, TOSA_KEY_MAIL), + KEY(6, 5, KEY_LEFT), + KEY(6, 6, KEY_DOWN), + KEY(6, 7, KEY_RIGHT), }; static struct matrix_keymap_data tosakbd_keymap_data = { diff --git a/arch/arm/mach-s3c64xx/mach-s3c64xx-dt.c b/arch/arm/mach-s3c64xx/mach-s3c64xx-dt.c index 7eb9a10..2fddf38 100644 --- a/arch/arm/mach-s3c64xx/mach-s3c64xx-dt.c +++ b/arch/arm/mach-s3c64xx/mach-s3c64xx-dt.c @@ -8,8 +8,6 @@ * published by the Free Software Foundation. */ -#include <linux/clk-provider.h> -#include <linux/irqchip.h> #include <linux/of_platform.h> #include <asm/mach/arch.h> @@ -48,15 +46,9 @@ static void __init s3c64xx_dt_map_io(void) panic("SoC is not S3C64xx!"); } -static void __init s3c64xx_dt_init_irq(void) -{ - of_clk_init(NULL); - samsung_wdt_reset_of_init(); - irqchip_init(); -}; - static void __init s3c64xx_dt_init_machine(void) { + samsung_wdt_reset_of_init(); of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL); } @@ -79,7 +71,6 @@ DT_MACHINE_START(S3C6400_DT, "Samsung S3C64xx (Flattened Device Tree)") /* Maintainer: Tomasz Figa <tomasz.figa@gmail.com> */ .dt_compat = s3c64xx_dt_compat, .map_io = s3c64xx_dt_map_io, - .init_irq = s3c64xx_dt_init_irq, .init_machine = s3c64xx_dt_init_machine, .restart = s3c64xx_dt_restart, MACHINE_END diff --git a/arch/arm/mach-shmobile/board-armadillo800eva.c b/arch/arm/mach-shmobile/board-armadillo800eva.c index 958e3cb..8ea87bd 100644 --- a/arch/arm/mach-shmobile/board-armadillo800eva.c +++ b/arch/arm/mach-shmobile/board-armadillo800eva.c @@ -483,7 +483,7 @@ static struct platform_device lcdc0_device = { .id = 0, .dev = { .platform_data = &lcdc0_info, - .coherent_dma_mask = ~0, + .coherent_dma_mask = DMA_BIT_MASK(32), }, }; @@ -580,7 +580,7 @@ static struct platform_device hdmi_lcdc_device = { .id = 1, .dev = { .platform_data = &hdmi_lcdc_info, - .coherent_dma_mask = ~0, + .coherent_dma_mask = DMA_BIT_MASK(32), }, }; @@ -614,6 +614,11 @@ static struct regulator_consumer_supply fixed3v3_power_consumers[] = { REGULATOR_SUPPLY("vqmmc", "sh_mmcif"), }; +/* Fixed 3.3V regulator used by LCD backlight */ +static struct regulator_consumer_supply fixed5v0_power_consumers[] = { + REGULATOR_SUPPLY("power", "pwm-backlight.0"), +}; + /* Fixed 3.3V regulator to be used by SDHI0 */ static struct regulator_consumer_supply vcc_sdhi0_consumers[] = { REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.0"), @@ -1196,6 +1201,8 @@ static void __init eva_init(void) regulator_register_always_on(0, "fixed-3.3V", fixed3v3_power_consumers, ARRAY_SIZE(fixed3v3_power_consumers), 3300000); + regulator_register_always_on(3, "fixed-5.0V", fixed5v0_power_consumers, + ARRAY_SIZE(fixed5v0_power_consumers), 5000000); pinctrl_register_mappings(eva_pinctrl_map, ARRAY_SIZE(eva_pinctrl_map)); pwm_add_table(pwm_lookup, ARRAY_SIZE(pwm_lookup)); diff --git a/arch/arm/mach-shmobile/board-bockw.c b/arch/arm/mach-shmobile/board-bockw.c index 38611526..3c4995a 100644 --- a/arch/arm/mach-shmobile/board-bockw.c +++ b/arch/arm/mach-shmobile/board-bockw.c @@ -679,7 +679,7 @@ static void __init bockw_init(void) .id = i, .data = &rsnd_card_info[i], .size_data = sizeof(struct asoc_simple_card_info), - .dma_mask = ~0, + .dma_mask = DMA_BIT_MASK(32), }; platform_device_register_full(&cardinfo); diff --git a/arch/arm/mach-shmobile/board-kzm9g.c b/arch/arm/mach-shmobile/board-kzm9g.c index fe689b7..bc40b85 100644 --- a/arch/arm/mach-shmobile/board-kzm9g.c +++ b/arch/arm/mach-shmobile/board-kzm9g.c @@ -334,7 +334,7 @@ static struct platform_device lcdc_device = { .resource = lcdc_resources, .dev = { .platform_data = &lcdc_info, - .coherent_dma_mask = ~0, + .coherent_dma_mask = DMA_BIT_MASK(32), }, }; diff --git a/arch/arm/mach-shmobile/board-lager.c b/arch/arm/mach-shmobile/board-lager.c index a8d3ce6..e0406fd 100644 --- a/arch/arm/mach-shmobile/board-lager.c +++ b/arch/arm/mach-shmobile/board-lager.c @@ -245,7 +245,9 @@ static void __init lager_init(void) { lager_add_standard_devices(); - phy_register_fixup_for_id("r8a7790-ether-ff:01", lager_ksz8041_fixup); + if (IS_ENABLED(CONFIG_PHYLIB)) + phy_register_fixup_for_id("r8a7790-ether-ff:01", + lager_ksz8041_fixup); } static const char * const lager_boards_compat_dt[] __initconst = { diff --git a/arch/arm/mach-shmobile/board-mackerel.c b/arch/arm/mach-shmobile/board-mackerel.c index af06753..e721d2c 100644 --- a/arch/arm/mach-shmobile/board-mackerel.c +++ b/arch/arm/mach-shmobile/board-mackerel.c @@ -409,7 +409,7 @@ static struct platform_device lcdc_device = { .resource = lcdc_resources, .dev = { .platform_data = &lcdc_info, - .coherent_dma_mask = ~0, + .coherent_dma_mask = DMA_BIT_MASK(32), }, }; @@ -499,7 +499,7 @@ static struct platform_device hdmi_lcdc_device = { .id = 1, .dev = { .platform_data = &hdmi_lcdc_info, - .coherent_dma_mask = ~0, + .coherent_dma_mask = DMA_BIT_MASK(32), }, }; diff --git a/arch/arm/mach-socfpga/Kconfig b/arch/arm/mach-socfpga/Kconfig index 037100a..aee77f0 100644 --- a/arch/arm/mach-socfpga/Kconfig +++ b/arch/arm/mach-socfpga/Kconfig @@ -10,6 +10,7 @@ config ARCH_SOCFPGA select GENERIC_CLOCKEVENTS select GPIO_PL061 if GPIOLIB select HAVE_ARM_SCU + select HAVE_ARM_TWD if SMP select HAVE_SMP select MFD_SYSCON select SPARSE_IRQ diff --git a/arch/arm/mach-tegra/fuse.c b/arch/arm/mach-tegra/fuse.c index 9a4e910..3a9c1f1 100644 --- a/arch/arm/mach-tegra/fuse.c +++ b/arch/arm/mach-tegra/fuse.c @@ -198,10 +198,12 @@ void __init tegra_init_fuse(void) switch (tegra_chip_id) { case TEGRA20: tegra20_fuse_init_randomness(); + break; case TEGRA30: case TEGRA114: default: tegra30_fuse_init_randomness(); + break; } pr_info("Tegra Revision: %s SKU: %d CPU Process: %d Core Process: %d\n", diff --git a/arch/arm/mach-ux500/cpu-db8500.c b/arch/arm/mach-ux500/cpu-db8500.c index 2e85c1e..12c7e5c 100644 --- a/arch/arm/mach-ux500/cpu-db8500.c +++ b/arch/arm/mach-ux500/cpu-db8500.c @@ -140,6 +140,10 @@ static struct of_dev_auxdata u8500_auxdata_lookup[] __initdata = { /* Requires call-back bindings. */ OF_DEV_AUXDATA("arm,cortex-a9-pmu", 0, "arm-pmu", &db8500_pmu_platdata), /* Requires DMA bindings. */ + OF_DEV_AUXDATA("arm,pl18x", 0x80126000, "sdi0", &mop500_sdi0_data), + OF_DEV_AUXDATA("arm,pl18x", 0x80118000, "sdi1", &mop500_sdi1_data), + OF_DEV_AUXDATA("arm,pl18x", 0x80005000, "sdi2", &mop500_sdi2_data), + OF_DEV_AUXDATA("arm,pl18x", 0x80114000, "sdi4", &mop500_sdi4_data), OF_DEV_AUXDATA("stericsson,ux500-msp-i2s", 0x80123000, "ux500-msp-i2s.0", &msp0_platform_data), OF_DEV_AUXDATA("stericsson,ux500-msp-i2s", 0x80124000, diff --git a/arch/arm/mm/dma-mapping.c b/arch/arm/mm/dma-mapping.c index f6b6bfa..f61a570 100644 --- a/arch/arm/mm/dma-mapping.c +++ b/arch/arm/mm/dma-mapping.c @@ -158,13 +158,49 @@ struct dma_map_ops arm_coherent_dma_ops = { }; EXPORT_SYMBOL(arm_coherent_dma_ops); +static int __dma_supported(struct device *dev, u64 mask, bool warn) +{ + unsigned long max_dma_pfn; + + /* + * If the mask allows for more memory than we can address, + * and we actually have that much memory, then we must + * indicate that DMA to this device is not supported. + */ + if (sizeof(mask) != sizeof(dma_addr_t) && + mask > (dma_addr_t)~0 && + dma_to_pfn(dev, ~0) < max_pfn) { + if (warn) { + dev_warn(dev, "Coherent DMA mask %#llx is larger than dma_addr_t allows\n", + mask); + dev_warn(dev, "Driver did not use or check the return value from dma_set_coherent_mask()?\n"); + } + return 0; + } + + max_dma_pfn = min(max_pfn, arm_dma_pfn_limit); + + /* + * Translate the device's DMA mask to a PFN limit. This + * PFN number includes the page which we can DMA to. + */ + if (dma_to_pfn(dev, mask) < max_dma_pfn) { + if (warn) + dev_warn(dev, "Coherent DMA mask %#llx (pfn %#lx-%#lx) covers a smaller range of system memory than the DMA zone pfn 0x0-%#lx\n", + mask, + dma_to_pfn(dev, 0), dma_to_pfn(dev, mask) + 1, + max_dma_pfn + 1); + return 0; + } + + return 1; +} + static u64 get_coherent_dma_mask(struct device *dev) { u64 mask = (u64)DMA_BIT_MASK(32); if (dev) { - unsigned long max_dma_pfn; - mask = dev->coherent_dma_mask; /* @@ -176,34 +212,8 @@ static u64 get_coherent_dma_mask(struct device *dev) return 0; } - max_dma_pfn = min(max_pfn, arm_dma_pfn_limit); - - /* - * If the mask allows for more memory than we can address, - * and we actually have that much memory, then fail the - * allocation. - */ - if (sizeof(mask) != sizeof(dma_addr_t) && - mask > (dma_addr_t)~0 && - dma_to_pfn(dev, ~0) > max_dma_pfn) { - dev_warn(dev, "Coherent DMA mask %#llx is larger than dma_addr_t allows\n", - mask); - dev_warn(dev, "Driver did not use or check the return value from dma_set_coherent_mask()?\n"); - return 0; - } - - /* - * Now check that the mask, when translated to a PFN, - * fits within the allowable addresses which we can - * allocate. - */ - if (dma_to_pfn(dev, mask) < max_dma_pfn) { - dev_warn(dev, "Coherent DMA mask %#llx (pfn %#lx-%#lx) covers a smaller range of system memory than the DMA zone pfn 0x0-%#lx\n", - mask, - dma_to_pfn(dev, 0), dma_to_pfn(dev, mask) + 1, - arm_dma_pfn_limit + 1); + if (!__dma_supported(dev, mask, true)) return 0; - } } return mask; @@ -1032,28 +1042,7 @@ void arm_dma_sync_sg_for_device(struct device *dev, struct scatterlist *sg, */ int dma_supported(struct device *dev, u64 mask) { - unsigned long limit; - - /* - * If the mask allows for more memory than we can address, - * and we actually have that much memory, then we must - * indicate that DMA to this device is not supported. - */ - if (sizeof(mask) != sizeof(dma_addr_t) && - mask > (dma_addr_t)~0 && - dma_to_pfn(dev, ~0) > arm_dma_pfn_limit) - return 0; - - /* - * Translate the device's DMA mask to a PFN limit. This - * PFN number includes the page which we can DMA to. - */ - limit = dma_to_pfn(dev, mask); - - if (limit < arm_dma_pfn_limit) - return 0; - - return 1; + return __dma_supported(dev, mask, false); } EXPORT_SYMBOL(dma_supported); diff --git a/arch/arm/mm/flush.c b/arch/arm/mm/flush.c index 6d5ba9a..3387e60 100644 --- a/arch/arm/mm/flush.c +++ b/arch/arm/mm/flush.c @@ -175,16 +175,16 @@ void __flush_dcache_page(struct address_space *mapping, struct page *page) unsigned long i; if (cache_is_vipt_nonaliasing()) { for (i = 0; i < (1 << compound_order(page)); i++) { - void *addr = kmap_atomic(page); + void *addr = kmap_atomic(page + i); __cpuc_flush_dcache_area(addr, PAGE_SIZE); kunmap_atomic(addr); } } else { for (i = 0; i < (1 << compound_order(page)); i++) { - void *addr = kmap_high_get(page); + void *addr = kmap_high_get(page + i); if (addr) { __cpuc_flush_dcache_area(addr, PAGE_SIZE); - kunmap_high(page); + kunmap_high(page + i); } } } diff --git a/arch/arm/mm/init.c b/arch/arm/mm/init.c index 3e8f106e..1f7b19a 100644 --- a/arch/arm/mm/init.c +++ b/arch/arm/mm/init.c @@ -229,7 +229,7 @@ void __init setup_dma_zone(const struct machine_desc *mdesc) #ifdef CONFIG_ZONE_DMA if (mdesc->dma_zone_size) { arm_dma_zone_size = mdesc->dma_zone_size; - arm_dma_limit = PHYS_OFFSET + arm_dma_zone_size - 1; + arm_dma_limit = __pv_phys_offset + arm_dma_zone_size - 1; } else arm_dma_limit = 0xffffffff; arm_dma_pfn_limit = arm_dma_limit >> PAGE_SHIFT; diff --git a/arch/arm/plat-omap/include/plat/dmtimer.h b/arch/arm/plat-omap/include/plat/dmtimer.h index fb92abb..2861b15 100644 --- a/arch/arm/plat-omap/include/plat/dmtimer.h +++ b/arch/arm/plat-omap/include/plat/dmtimer.h @@ -336,8 +336,11 @@ static inline void __omap_dm_timer_enable_posted(struct omap_dm_timer *timer) if (timer->posted) return; - if (timer->errata & OMAP_TIMER_ERRATA_I103_I767) + if (timer->errata & OMAP_TIMER_ERRATA_I103_I767) { + timer->posted = OMAP_TIMER_NONPOSTED; + __omap_dm_timer_write(timer, OMAP_TIMER_IF_CTRL_REG, 0, 0); return; + } __omap_dm_timer_write(timer, OMAP_TIMER_IF_CTRL_REG, OMAP_TIMER_CTRL_POSTED, 0); diff --git a/arch/arm/xen/enlighten.c b/arch/arm/xen/enlighten.c index 83e4f95..8550123 100644 --- a/arch/arm/xen/enlighten.c +++ b/arch/arm/xen/enlighten.c @@ -96,7 +96,7 @@ static int remap_pte_fn(pte_t *ptep, pgtable_t token, unsigned long addr, struct remap_data *info = data; struct page *page = info->pages[info->index++]; unsigned long pfn = page_to_pfn(page); - pte_t pte = pfn_pte(pfn, info->prot); + pte_t pte = pte_mkspecial(pfn_pte(pfn, info->prot)); if (map_foreign_page(pfn, info->fgmfn, info->domid)) return -EFAULT; @@ -224,10 +224,10 @@ static int __init xen_guest_init(void) } if (of_address_to_resource(node, GRANT_TABLE_PHYSADDR, &res)) return 0; - xen_hvm_resume_frames = res.start >> PAGE_SHIFT; + xen_hvm_resume_frames = res.start; xen_events_irq = irq_of_parse_and_map(node, 0); pr_info("Xen %s support found, events_irq=%d gnttab_frame_pfn=%lx\n", - version, xen_events_irq, xen_hvm_resume_frames); + version, xen_events_irq, (xen_hvm_resume_frames >> PAGE_SHIFT)); xen_domain_type = XEN_HVM_DOMAIN; xen_setup_features(); |
