diff options
Diffstat (limited to 'arch/arm')
119 files changed, 1375 insertions, 533 deletions
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 4f8760d..184a6bd 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -18,6 +18,8 @@ config ARM select HAVE_KRETPROBES if (HAVE_KPROBES) select HAVE_FUNCTION_TRACER if (!XIP_KERNEL) select HAVE_GENERIC_DMA_COHERENT + select HAVE_KERNEL_GZIP + select HAVE_KERNEL_LZO help The ARM series is a line of low-power-consumption RISC chip designs licensed by ARM Ltd and targeted at embedded applications and @@ -700,6 +702,7 @@ config ARCH_OMAP select ARCH_HAS_CPUFREQ select GENERIC_TIME select GENERIC_CLOCKEVENTS + select ARCH_HAS_HOLES_MEMORYMODEL help Support for TI's OMAP platform (OMAP1 and OMAP2). @@ -727,14 +730,26 @@ config ARCH_U8500 endchoice +source "arch/arm/mach-aaec2000/Kconfig" + +source "arch/arm/mach-at91/Kconfig" + +source "arch/arm/mach-bcmring/Kconfig" + source "arch/arm/mach-clps711x/Kconfig" +source "arch/arm/mach-davinci/Kconfig" + +source "arch/arm/mach-dove/Kconfig" + source "arch/arm/mach-ep93xx/Kconfig" source "arch/arm/mach-footbridge/Kconfig" source "arch/arm/mach-gemini/Kconfig" +source "arch/arm/mach-h720x/Kconfig" + source "arch/arm/mach-integrator/Kconfig" source "arch/arm/mach-iop32x/Kconfig" @@ -749,16 +764,26 @@ source "arch/arm/mach-ixp2000/Kconfig" source "arch/arm/mach-ixp23xx/Kconfig" +source "arch/arm/mach-kirkwood/Kconfig" + +source "arch/arm/mach-ks8695/Kconfig" + +source "arch/arm/mach-lh7a40x/Kconfig" + source "arch/arm/mach-loki/Kconfig" +source "arch/arm/mach-msm/Kconfig" + source "arch/arm/mach-mv78xx0/Kconfig" -source "arch/arm/mach-pxa/Kconfig" -source "arch/arm/plat-pxa/Kconfig" +source "arch/arm/plat-mxc/Kconfig" -source "arch/arm/mach-mmp/Kconfig" +source "arch/arm/mach-netx/Kconfig" -source "arch/arm/mach-sa1100/Kconfig" +source "arch/arm/mach-nomadik/Kconfig" +source "arch/arm/plat-nomadik/Kconfig" + +source "arch/arm/mach-ns9xxx/Kconfig" source "arch/arm/plat-omap/Kconfig" @@ -768,9 +793,14 @@ source "arch/arm/mach-omap2/Kconfig" source "arch/arm/mach-orion5x/Kconfig" -source "arch/arm/mach-kirkwood/Kconfig" +source "arch/arm/mach-pxa/Kconfig" +source "arch/arm/plat-pxa/Kconfig" -source "arch/arm/mach-dove/Kconfig" +source "arch/arm/mach-mmp/Kconfig" + +source "arch/arm/mach-realview/Kconfig" + +source "arch/arm/mach-sa1100/Kconfig" source "arch/arm/plat-samsung/Kconfig" source "arch/arm/plat-s3c24xx/Kconfig" @@ -798,41 +828,14 @@ if ARCH_S5PC1XX source "arch/arm/mach-s5pc100/Kconfig" endif -source "arch/arm/mach-lh7a40x/Kconfig" +source "arch/arm/mach-u300/Kconfig" -source "arch/arm/mach-h720x/Kconfig" +source "arch/arm/mach-ux500/Kconfig" source "arch/arm/mach-versatile/Kconfig" -source "arch/arm/mach-aaec2000/Kconfig" - -source "arch/arm/mach-realview/Kconfig" - -source "arch/arm/mach-at91/Kconfig" - -source "arch/arm/plat-mxc/Kconfig" - -source "arch/arm/mach-nomadik/Kconfig" -source "arch/arm/plat-nomadik/Kconfig" - -source "arch/arm/mach-netx/Kconfig" - -source "arch/arm/mach-ns9xxx/Kconfig" - -source "arch/arm/mach-davinci/Kconfig" - -source "arch/arm/mach-ks8695/Kconfig" - -source "arch/arm/mach-msm/Kconfig" - -source "arch/arm/mach-u300/Kconfig" - source "arch/arm/mach-w90x900/Kconfig" -source "arch/arm/mach-bcmring/Kconfig" - -source "arch/arm/mach-ux500/Kconfig" - # Definitions to make life easier config ARCH_ACORN bool diff --git a/arch/arm/Makefile b/arch/arm/Makefile index e9da084..356d702 100644 --- a/arch/arm/Makefile +++ b/arch/arm/Makefile @@ -94,7 +94,7 @@ CFLAGS_ABI +=-funwind-tables endif ifeq ($(CONFIG_THUMB2_KERNEL),y) -AFLAGS_AUTOIT :=$(call as-option,-Wa$(comma)-mimplicit-it=thumb,-Wa$(comma)-mauto-it) +AFLAGS_AUTOIT :=$(call as-option,-Wa$(comma)-mimplicit-it=always,-Wa$(comma)-mauto-it) AFLAGS_NOWARN :=$(call as-option,-Wa$(comma)-mno-warn-deprecated,-Wa$(comma)-W) CFLAGS_THUMB2 :=-mthumb $(AFLAGS_AUTOIT) $(AFLAGS_NOWARN) AFLAGS_THUMB2 :=$(CFLAGS_THUMB2) -Wa$(comma)-mthumb @@ -146,6 +146,7 @@ machine-$(CONFIG_ARCH_MX1) := mx1 machine-$(CONFIG_ARCH_MX2) := mx2 machine-$(CONFIG_ARCH_MX25) := mx25 machine-$(CONFIG_ARCH_MX3) := mx3 +machine-$(CONFIG_ARCH_MXC91231) := mxc91231 machine-$(CONFIG_ARCH_NETX) := netx machine-$(CONFIG_ARCH_NOMADIK) := nomadik machine-$(CONFIG_ARCH_NS9XXX) := ns9xxx @@ -171,12 +172,12 @@ machine-$(CONFIG_ARCH_U8500) := ux500 machine-$(CONFIG_ARCH_VERSATILE) := versatile machine-$(CONFIG_ARCH_W90X900) := w90x900 machine-$(CONFIG_FOOTBRIDGE) := footbridge -machine-$(CONFIG_ARCH_MXC91231) := mxc91231 # Platform directory name. This list is sorted alphanumerically # by CONFIG_* macro name. plat-$(CONFIG_ARCH_MXC) := mxc plat-$(CONFIG_ARCH_OMAP) := omap +plat-$(CONFIG_ARCH_STMP3XXX) := stmp3xxx plat-$(CONFIG_PLAT_IOP) := iop plat-$(CONFIG_PLAT_NOMADIK) := nomadik plat-$(CONFIG_PLAT_ORION) := orion @@ -184,7 +185,6 @@ plat-$(CONFIG_PLAT_PXA) := pxa plat-$(CONFIG_PLAT_S3C24XX) := s3c24xx s3c samsung plat-$(CONFIG_PLAT_S3C64XX) := s3c64xx s3c samsung plat-$(CONFIG_PLAT_S5PC1XX) := s5pc1xx s3c samsung -plat-$(CONFIG_ARCH_STMP3XXX) := stmp3xxx ifeq ($(CONFIG_ARCH_EBSA110),y) # This is what happens if you forget the IOCS16 line. diff --git a/arch/arm/boot/compressed/Makefile b/arch/arm/boot/compressed/Makefile index ce39dc5..2d4d88b 100644 --- a/arch/arm/boot/compressed/Makefile +++ b/arch/arm/boot/compressed/Makefile @@ -63,8 +63,12 @@ endif SEDFLAGS = s/TEXT_START/$(ZTEXTADDR)/;s/BSS_START/$(ZBSSADDR)/ -targets := vmlinux vmlinux.lds piggy.gz piggy.o font.o font.c \ - head.o misc.o $(OBJS) +suffix_$(CONFIG_KERNEL_GZIP) = gzip +suffix_$(CONFIG_KERNEL_LZO) = lzo + +targets := vmlinux vmlinux.lds \ + piggy.$(suffix_y) piggy.$(suffix_y).o \ + font.o font.c head.o misc.o $(OBJS) ifeq ($(CONFIG_FUNCTION_TRACER),y) ORIG_CFLAGS := $(KBUILD_CFLAGS) @@ -87,22 +91,34 @@ endif ifneq ($(PARAMS_PHYS),) LDFLAGS_vmlinux += --defsym params_phys=$(PARAMS_PHYS) endif -LDFLAGS_vmlinux += -p --no-undefined -X \ - $(shell $(CC) $(KBUILD_CFLAGS) --print-libgcc-file-name) -T +# ? +LDFLAGS_vmlinux += -p +# Report unresolved symbol references +LDFLAGS_vmlinux += --no-undefined +# Delete all temporary local symbols +LDFLAGS_vmlinux += -X +# Next argument is a linker script +LDFLAGS_vmlinux += -T + +# For __aeabi_uidivmod +lib1funcs = $(obj)/lib1funcs.o + +$(obj)/lib1funcs.S: $(srctree)/arch/$(SRCARCH)/lib/lib1funcs.S FORCE + $(call cmd,shipped) # Don't allow any static data in misc.o, which # would otherwise mess up our GOT table CFLAGS_misc.o := -Dstatic= -$(obj)/vmlinux: $(obj)/vmlinux.lds $(obj)/$(HEAD) $(obj)/piggy.o \ - $(addprefix $(obj)/, $(OBJS)) FORCE +$(obj)/vmlinux: $(obj)/vmlinux.lds $(obj)/$(HEAD) $(obj)/piggy.$(suffix_y).o \ + $(addprefix $(obj)/, $(OBJS)) $(lib1funcs) FORCE $(call if_changed,ld) @: -$(obj)/piggy.gz: $(obj)/../Image FORCE - $(call if_changed,gzip) +$(obj)/piggy.$(suffix_y): $(obj)/../Image FORCE + $(call if_changed,$(suffix_y)) -$(obj)/piggy.o: $(obj)/piggy.gz FORCE +$(obj)/piggy.$(suffix_y).o: $(obj)/piggy.$(suffix_y) FORCE CFLAGS_font.o := -Dstatic= diff --git a/arch/arm/boot/compressed/head.S b/arch/arm/boot/compressed/head.S index d356af7..4fddc50 100644 --- a/arch/arm/boot/compressed/head.S +++ b/arch/arm/boot/compressed/head.S @@ -27,6 +27,14 @@ .macro writeb, ch, rb mcr p14, 0, \ch, c0, c5, 0 .endm +#elif defined(CONFIG_CPU_V7) + .macro loadsp, rb + .endm + .macro writeb, ch, rb +wait: mrc p14, 0, pc, c0, c1, 0 + bcs wait + mcr p14, 0, \ch, c0, c5, 0 + .endm #elif defined(CONFIG_CPU_XSCALE) .macro loadsp, rb .endm diff --git a/arch/arm/boot/compressed/misc.c b/arch/arm/boot/compressed/misc.c index 17153b5..56a0d11 100644 --- a/arch/arm/boot/compressed/misc.c +++ b/arch/arm/boot/compressed/misc.c @@ -18,10 +18,15 @@ unsigned int __machine_arch_type; +#define _LINUX_STRING_H_ + #include <linux/compiler.h> /* for inline */ #include <linux/types.h> /* for size_t */ #include <linux/stddef.h> /* for NULL */ #include <asm/string.h> +#include <linux/linkage.h> + +#include <asm/unaligned.h> #ifdef STANDALONE_DEBUG #define putstr printf @@ -48,6 +53,18 @@ static void icedcc_putc(int ch) asm("mcr p14, 0, %0, c0, c5, 0" : : "r" (ch)); } + +#elif defined(CONFIG_CPU_V7) + +static void icedcc_putc(int ch) +{ + asm( + "wait: mrc p14, 0, pc, c0, c1, 0 \n\ + bcs wait \n\ + mcr p14, 0, %0, c0, c5, 0 " + : : "r" (ch)); +} + #elif defined(CONFIG_CPU_XSCALE) static void icedcc_putc(int ch) @@ -83,7 +100,6 @@ static void icedcc_putc(int ch) #endif #define putc(ch) icedcc_putc(ch) -#define flush() do { } while (0) #endif static void putstr(const char *ptr) @@ -188,34 +204,8 @@ static inline __ptr_t memcpy(__ptr_t __dest, __const __ptr_t __src, /* * gzip delarations */ -#define OF(args) args #define STATIC static -typedef unsigned char uch; -typedef unsigned short ush; -typedef unsigned long ulg; - -#define WSIZE 0x8000 /* Window size must be at least 32k, */ - /* and a power of two */ - -static uch *inbuf; /* input buffer */ -static uch window[WSIZE]; /* Sliding window buffer */ - -static unsigned insize; /* valid bytes in inbuf */ -static unsigned inptr; /* index of next byte to be processed in inbuf */ -static unsigned outcnt; /* bytes in output buffer */ - -/* gzip flag byte */ -#define ASCII_FLAG 0x01 /* bit 0 set: file probably ascii text */ -#define CONTINUATION 0x02 /* bit 1 set: continuation of multi-part gzip file */ -#define EXTRA_FIELD 0x04 /* bit 2 set: extra field present */ -#define ORIG_NAME 0x08 /* bit 3 set: original file name present */ -#define COMMENT 0x10 /* bit 4 set: file comment present */ -#define ENCRYPTED 0x20 /* bit 5 set: file is encrypted */ -#define RESERVED 0xC0 /* bit 6,7: reserved */ - -#define get_byte() (inptr < insize ? inbuf[inptr++] : fill_inbuf()) - /* Diagnostic functions */ #ifdef DEBUG # define Assert(cond,msg) {if(!(cond)) error(msg);} @@ -233,24 +223,20 @@ static unsigned outcnt; /* bytes in output buffer */ # define Tracecv(c,x) #endif -static int fill_inbuf(void); -static void flush_window(void); static void error(char *m); extern char input_data[]; extern char input_data_end[]; -static uch *output_data; -static ulg output_ptr; -static ulg bytes_out; +static unsigned char *output_data; +static unsigned long output_ptr; static void error(char *m); static void putstr(const char *); -extern int end; -static ulg free_mem_ptr; -static ulg free_mem_end_ptr; +static unsigned long free_mem_ptr; +static unsigned long free_mem_end_ptr; #ifdef STANDALONE_DEBUG #define NO_INFLATE_MALLOC @@ -258,46 +244,13 @@ static ulg free_mem_end_ptr; #define ARCH_HAS_DECOMP_WDOG -#include "../../../../lib/inflate.c" - -/* =========================================================================== - * Fill the input buffer. This is called only when the buffer is empty - * and at least one byte is really needed. - */ -int fill_inbuf(void) -{ - if (insize != 0) - error("ran out of input data"); - - inbuf = input_data; - insize = &input_data_end[0] - &input_data[0]; - - inptr = 1; - return inbuf[0]; -} +#ifdef CONFIG_KERNEL_GZIP +#include "../../../../lib/decompress_inflate.c" +#endif -/* =========================================================================== - * Write the output window window[0..outcnt-1] and update crc and bytes_out. - * (Used for the decompressed data only.) - */ -void flush_window(void) -{ - ulg c = crc; - unsigned n; - uch *in, *out, ch; - - in = window; - out = &output_data[output_ptr]; - for (n = 0; n < outcnt; n++) { - ch = *out++ = *in++; - c = crc_32_tab[((int)c ^ ch) & 0xff] ^ (c >> 8); - } - crc = c; - bytes_out += (ulg)outcnt; - output_ptr += (ulg)outcnt; - outcnt = 0; - putstr("."); -} +#ifdef CONFIG_KERNEL_LZO +#include "../../../../lib/decompress_unlzo.c" +#endif #ifndef arch_error #define arch_error(x) @@ -314,22 +267,33 @@ static void error(char *x) while(1); /* Halt */ } +asmlinkage void __div0(void) +{ + error("Attempting division by 0!"); +} + #ifndef STANDALONE_DEBUG -ulg -decompress_kernel(ulg output_start, ulg free_mem_ptr_p, ulg free_mem_ptr_end_p, - int arch_id) +unsigned long +decompress_kernel(unsigned long output_start, unsigned long free_mem_ptr_p, + unsigned long free_mem_ptr_end_p, + int arch_id) { - output_data = (uch *)output_start; /* Points to kernel start */ + unsigned char *tmp; + + output_data = (unsigned char *)output_start; free_mem_ptr = free_mem_ptr_p; free_mem_end_ptr = free_mem_ptr_end_p; __machine_arch_type = arch_id; arch_decomp_setup(); - makecrc(); + tmp = (unsigned char *) (((unsigned long)input_data_end) - 4); + output_ptr = get_unaligned_le32(tmp); + putstr("Uncompressing Linux..."); - gunzip(); + decompress(input_data, input_data_end - input_data, + NULL, NULL, output_data, NULL, error); putstr(" done, booting the kernel.\n"); return output_ptr; } @@ -341,11 +305,10 @@ int main() { output_data = output_buffer; - makecrc(); putstr("Uncompressing Linux..."); - gunzip(); + decompress(input_data, input_data_end - input_data, + NULL, NULL, output_data, NULL, error); putstr("done.\n"); return 0; } #endif - diff --git a/arch/arm/boot/compressed/piggy.gzip.S b/arch/arm/boot/compressed/piggy.gzip.S new file mode 100644 index 0000000..a68adf9 --- /dev/null +++ b/arch/arm/boot/compressed/piggy.gzip.S @@ -0,0 +1,6 @@ + .section .piggydata,#alloc + .globl input_data +input_data: + .incbin "arch/arm/boot/compressed/piggy.gzip" + .globl input_data_end +input_data_end: diff --git a/arch/arm/boot/compressed/piggy.S b/arch/arm/boot/compressed/piggy.lzo.S index 54c9518..a425ad9 100644 --- a/arch/arm/boot/compressed/piggy.S +++ b/arch/arm/boot/compressed/piggy.lzo.S @@ -1,6 +1,6 @@ .section .piggydata,#alloc .globl input_data input_data: - .incbin "arch/arm/boot/compressed/piggy.gz" + .incbin "arch/arm/boot/compressed/piggy.lzo" .globl input_data_end input_data_end: diff --git a/arch/arm/configs/u300_defconfig b/arch/arm/configs/u300_defconfig index 610ac3c..9155196 100644 --- a/arch/arm/configs/u300_defconfig +++ b/arch/arm/configs/u300_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.32-rc5 -# Sat Oct 17 23:32:24 2009 +# Linux kernel version: 2.6.33-rc2 +# Wed Jan 6 00:01:36 2010 # CONFIG_ARM=y CONFIG_SYS_SUPPORTS_APM_EMULATION=y @@ -46,6 +46,7 @@ CONFIG_SYSVIPC_SYSCTL=y # CONFIG_TREE_RCU=y # CONFIG_TREE_PREEMPT_RCU is not set +# CONFIG_TINY_RCU is not set # CONFIG_RCU_TRACE is not set CONFIG_RCU_FANOUT=32 # CONFIG_RCU_FANOUT_EXACT is not set @@ -119,14 +120,41 @@ CONFIG_BLOCK=y # IO Schedulers # CONFIG_IOSCHED_NOOP=y -# CONFIG_IOSCHED_AS is not set CONFIG_IOSCHED_DEADLINE=y # CONFIG_IOSCHED_CFQ is not set -# CONFIG_DEFAULT_AS is not set CONFIG_DEFAULT_DEADLINE=y # CONFIG_DEFAULT_CFQ is not set # CONFIG_DEFAULT_NOOP is not set CONFIG_DEFAULT_IOSCHED="deadline" +# CONFIG_INLINE_SPIN_TRYLOCK is not set +# CONFIG_INLINE_SPIN_TRYLOCK_BH is not set +# CONFIG_INLINE_SPIN_LOCK is not set +# CONFIG_INLINE_SPIN_LOCK_BH is not set +# CONFIG_INLINE_SPIN_LOCK_IRQ is not set +# CONFIG_INLINE_SPIN_LOCK_IRQSAVE is not set +# CONFIG_INLINE_SPIN_UNLOCK is not set +# CONFIG_INLINE_SPIN_UNLOCK_BH is not set +# CONFIG_INLINE_SPIN_UNLOCK_IRQ is not set +# CONFIG_INLINE_SPIN_UNLOCK_IRQRESTORE is not set +# CONFIG_INLINE_READ_TRYLOCK is not set +# CONFIG_INLINE_READ_LOCK is not set +# CONFIG_INLINE_READ_LOCK_BH is not set +# CONFIG_INLINE_READ_LOCK_IRQ is not set +# CONFIG_INLINE_READ_LOCK_IRQSAVE is not set +# CONFIG_INLINE_READ_UNLOCK is not set +# CONFIG_INLINE_READ_UNLOCK_BH is not set +# CONFIG_INLINE_READ_UNLOCK_IRQ is not set +# CONFIG_INLINE_READ_UNLOCK_IRQRESTORE is not set +# CONFIG_INLINE_WRITE_TRYLOCK is not set +# CONFIG_INLINE_WRITE_LOCK is not set +# CONFIG_INLINE_WRITE_LOCK_BH is not set +# CONFIG_INLINE_WRITE_LOCK_IRQ is not set +# CONFIG_INLINE_WRITE_LOCK_IRQSAVE is not set +# CONFIG_INLINE_WRITE_UNLOCK is not set +# CONFIG_INLINE_WRITE_UNLOCK_BH is not set +# CONFIG_INLINE_WRITE_UNLOCK_IRQ is not set +# CONFIG_INLINE_WRITE_UNLOCK_IRQRESTORE is not set +# CONFIG_MUTEX_SPIN_ON_OWNER is not set # CONFIG_FREEZER is not set # @@ -155,6 +183,7 @@ CONFIG_MMU=y # CONFIG_ARCH_IXP2000 is not set # CONFIG_ARCH_IXP4XX is not set # CONFIG_ARCH_L7200 is not set +# CONFIG_ARCH_DOVE is not set # CONFIG_ARCH_KIRKWOOD is not set # CONFIG_ARCH_LOKI is not set # CONFIG_ARCH_MV78XX0 is not set @@ -177,6 +206,7 @@ CONFIG_ARCH_U300=y # CONFIG_ARCH_DAVINCI is not set # CONFIG_ARCH_OMAP is not set # CONFIG_ARCH_BCMRING is not set +# CONFIG_ARCH_U8500 is not set # # ST-Ericsson AB U300/U330/U335/U365 Platform @@ -265,12 +295,10 @@ CONFIG_FLATMEM_MANUAL=y CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y CONFIG_PAGEFLAGS_EXTENDED=y -CONFIG_SPLIT_PTLOCK_CPUS=4096 +CONFIG_SPLIT_PTLOCK_CPUS=999999 # CONFIG_PHYS_ADDR_T_64BIT is not set CONFIG_ZONE_DMA_FLAG=0 CONFIG_VIRT_TO_BUS=y -CONFIG_HAVE_MLOCK=y -CONFIG_HAVE_MLOCKED_PAGE_BIT=y # CONFIG_KSM is not set CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_ALIGNMENT_TRAP=y @@ -499,14 +527,21 @@ CONFIG_MTD_NAND_IDS=y CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_COW_COMMON is not set # CONFIG_BLK_DEV_LOOP is not set + +# +# DRBD disabled because PROC_FS, INET or CONNECTOR not selected +# # CONFIG_BLK_DEV_NBD is not set # CONFIG_BLK_DEV_RAM is not set # CONFIG_CDROM_PKTCDVD is not set # CONFIG_ATA_OVER_ETH is not set CONFIG_MISC_DEVICES=y +# CONFIG_AD525X_DPOT is not set # CONFIG_ICS932S401 is not set # CONFIG_ENCLOSURE_SERVICES is not set # CONFIG_ISL29003 is not set +# CONFIG_DS1682 is not set +# CONFIG_TI_DAC7512 is not set # CONFIG_C2PORT is not set # @@ -517,6 +552,7 @@ CONFIG_MISC_DEVICES=y # CONFIG_EEPROM_LEGACY is not set # CONFIG_EEPROM_MAX6875 is not set # CONFIG_EEPROM_93CX6 is not set +# CONFIG_IWMC3200TOP is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -539,6 +575,7 @@ CONFIG_HAVE_IDE=y CONFIG_INPUT=y # CONFIG_INPUT_FF_MEMLESS is not set # CONFIG_INPUT_POLLDEV is not set +# CONFIG_INPUT_SPARSEKMAP is not set # # Userland interfaces @@ -645,7 +682,6 @@ CONFIG_I2C_STU300=y # # Miscellaneous I2C Chip support # -# CONFIG_DS1682 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set @@ -661,6 +697,8 @@ CONFIG_SPI_MASTER=y # CONFIG_SPI_BITBANG is not set # CONFIG_SPI_GPIO is not set CONFIG_SPI_PL022=y +# CONFIG_SPI_XILINX is not set +# CONFIG_SPI_DESIGNWARE is not set # # SPI Protocol Masters @@ -708,6 +746,7 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_T7L66XB is not set # CONFIG_MFD_TC6387XB is not set # CONFIG_PMIC_DA903X is not set +# CONFIG_PMIC_ADP5520 is not set # CONFIG_MFD_WM8400 is not set # CONFIG_MFD_WM831X is not set # CONFIG_MFD_WM8350_I2C is not set @@ -716,6 +755,8 @@ CONFIG_SSB_POSSIBLE=y CONFIG_AB3100_CORE=y CONFIG_AB3100_OTP=y # CONFIG_EZX_PCAP is not set +# CONFIG_MFD_88PM8607 is not set +# CONFIG_AB4500_CORE is not set CONFIG_REGULATOR=y # CONFIG_REGULATOR_DEBUG is not set # CONFIG_REGULATOR_FIXED_VOLTAGE is not set @@ -723,6 +764,7 @@ CONFIG_REGULATOR=y # CONFIG_REGULATOR_USERSPACE_CONSUMER is not set # CONFIG_REGULATOR_BQ24022 is not set # CONFIG_REGULATOR_MAX1586 is not set +# CONFIG_REGULATOR_MAX8660 is not set # CONFIG_REGULATOR_LP3971 is not set CONFIG_REGULATOR_AB3100=y # CONFIG_REGULATOR_TPS65023 is not set @@ -840,7 +882,9 @@ CONFIG_LEDS_CLASS=y # CONFIG_LEDS_LP3944 is not set # CONFIG_LEDS_PCA955X is not set # CONFIG_LEDS_DAC124S085 is not set +# CONFIG_LEDS_REGULATOR is not set # CONFIG_LEDS_BD2802 is not set +# CONFIG_LEDS_LT3593 is not set # # LED Triggers @@ -882,6 +926,7 @@ CONFIG_RTC_INTF_DEV=y # CONFIG_RTC_DRV_PCF8563 is not set # CONFIG_RTC_DRV_PCF8583 is not set # CONFIG_RTC_DRV_M41T80 is not set +# CONFIG_RTC_DRV_BQ32K is not set # CONFIG_RTC_DRV_S35390A is not set # CONFIG_RTC_DRV_FM3130 is not set # CONFIG_RTC_DRV_RX8581 is not set @@ -911,7 +956,9 @@ CONFIG_RTC_INTF_DEV=y # CONFIG_RTC_DRV_M48T86 is not set # CONFIG_RTC_DRV_M48T35 is not set # CONFIG_RTC_DRV_M48T59 is not set +# CONFIG_RTC_DRV_MSM6242 is not set # CONFIG_RTC_DRV_BQ4802 is not set +# CONFIG_RTC_DRV_RP5C01 is not set # CONFIG_RTC_DRV_V3020 is not set CONFIG_RTC_DRV_AB3100=y @@ -926,6 +973,15 @@ CONFIG_DMADEVICES=y # # DMA Devices # +CONFIG_COH901318=y +CONFIG_DMA_ENGINE=y + +# +# DMA Clients +# +# CONFIG_NET_DMA is not set +# CONFIG_ASYNC_TX_DMA is not set +# CONFIG_DMATEST is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set @@ -1018,7 +1074,7 @@ CONFIG_MISC_FILESYSTEMS=y CONFIG_MSDOS_PARTITION=y CONFIG_NLS=y CONFIG_NLS_DEFAULT="iso8859-1" -# CONFIG_NLS_CODEPAGE_437 is not set +CONFIG_NLS_CODEPAGE_437=y # CONFIG_NLS_CODEPAGE_737 is not set # CONFIG_NLS_CODEPAGE_775 is not set # CONFIG_NLS_CODEPAGE_850 is not set @@ -1135,6 +1191,7 @@ CONFIG_ARM_UNWIND=y # CONFIG_DEBUG_ERRORS is not set # CONFIG_DEBUG_STACK_USAGE is not set # CONFIG_DEBUG_LL is not set +# CONFIG_OC_ETM is not set # # Security options @@ -1142,7 +1199,11 @@ CONFIG_ARM_UNWIND=y # CONFIG_KEYS is not set # CONFIG_SECURITY is not set # CONFIG_SECURITYFS is not set -# CONFIG_SECURITY_FILE_CAPABILITIES is not set +# CONFIG_DEFAULT_SECURITY_SELINUX is not set +# CONFIG_DEFAULT_SECURITY_SMACK is not set +# CONFIG_DEFAULT_SECURITY_TOMOYO is not set +CONFIG_DEFAULT_SECURITY_DAC=y +CONFIG_DEFAULT_SECURITY="" # CONFIG_CRYPTO is not set # CONFIG_BINARY_PRINTF is not set diff --git a/arch/arm/include/asm/cacheflush.h b/arch/arm/include/asm/cacheflush.h index 730aefc..c77d2fa 100644 --- a/arch/arm/include/asm/cacheflush.h +++ b/arch/arm/include/asm/cacheflush.h @@ -154,16 +154,16 @@ * Please note that the implementation of these, and the required * effects are cache-type (VIVT/VIPT/PIPT) specific. * - * flush_cache_kern_all() + * flush_kern_all() * * Unconditionally clean and invalidate the entire cache. * - * flush_cache_user_mm(mm) + * flush_user_all() * * Clean and invalidate all user space cache entries * before a change of page tables. * - * flush_cache_user_range(start, end, flags) + * flush_user_range(start, end, flags) * * Clean and invalidate a range of cache entries in the * specified address space before a change of page tables. @@ -179,6 +179,20 @@ * - start - virtual start address * - end - virtual end address * + * coherent_user_range(start, end) + * + * Ensure coherency between the Icache and the Dcache in the + * region described by start, end. If you have non-snooping + * Harvard caches, you need to implement this function. + * - start - virtual start address + * - end - virtual end address + * + * flush_kern_dcache_area(kaddr, size) + * + * Ensure that the data held in page is written back. + * - kaddr - page address + * - size - region size + * * DMA Cache Coherency * =================== * diff --git a/arch/arm/include/asm/cpu.h b/arch/arm/include/asm/cpu.h index 634b2d7..7939681 100644 --- a/arch/arm/include/asm/cpu.h +++ b/arch/arm/include/asm/cpu.h @@ -11,6 +11,7 @@ #define __ASM_ARM_CPU_H #include <linux/percpu.h> +#include <linux/cpu.h> struct cpuinfo_arm { struct cpu cpu; diff --git a/arch/arm/include/asm/dma.h b/arch/arm/include/asm/dma.h index 7edf353..ca51143 100644 --- a/arch/arm/include/asm/dma.h +++ b/arch/arm/include/asm/dma.h @@ -138,12 +138,12 @@ extern int get_dma_residue(unsigned int chan); #define NO_DMA 255 #endif +#endif /* CONFIG_ISA_DMA_API */ + #ifdef CONFIG_PCI extern int isa_dma_bridge_buggy; #else #define isa_dma_bridge_buggy (0) #endif -#endif /* CONFIG_ISA_DMA_API */ - #endif /* __ASM_ARM_DMA_H */ diff --git a/arch/arm/include/asm/ptrace.h b/arch/arm/include/asm/ptrace.h index bbecccd..eec6e89 100644 --- a/arch/arm/include/asm/ptrace.h +++ b/arch/arm/include/asm/ptrace.h @@ -97,9 +97,15 @@ * stack during a system call. Note that sizeof(struct pt_regs) * has to be a multiple of 8. */ +#ifndef __KERNEL__ struct pt_regs { long uregs[18]; }; +#else /* __KERNEL__ */ +struct pt_regs { + unsigned long uregs[18]; +}; +#endif /* __KERNEL__ */ #define ARM_cpsr uregs[16] #define ARM_pc uregs[15] diff --git a/arch/arm/include/asm/unistd.h b/arch/arm/include/asm/unistd.h index 4e506d0..cf9cdaa2 100644 --- a/arch/arm/include/asm/unistd.h +++ b/arch/arm/include/asm/unistd.h @@ -391,6 +391,7 @@ #define __NR_pwritev (__NR_SYSCALL_BASE+362) #define __NR_rt_tgsigqueueinfo (__NR_SYSCALL_BASE+363) #define __NR_perf_event_open (__NR_SYSCALL_BASE+364) +#define __NR_recvmmsg (__NR_SYSCALL_BASE+365) /* * The following SWIs are ARM private. diff --git a/arch/arm/kernel/debug.S b/arch/arm/kernel/debug.S index b121b60..5c91add 100644 --- a/arch/arm/kernel/debug.S +++ b/arch/arm/kernel/debug.S @@ -49,6 +49,26 @@ 1002: .endm +#elif defined(CONFIG_CPU_V7) + + .macro addruart, rx + .endm + + .macro senduart, rd, rx + mcr p14, 0, \rd, c0, c5, 0 + .endm + + .macro busyuart, rd, rx +busy: mrc p14, 0, pc, c0, c1, 0 + bcs busy + .endm + + .macro waituart, rd, rx +wait: mrc p14, 0, pc, c0, c1, 0 + bcs wait + + .endm + #elif defined(CONFIG_CPU_XSCALE) .macro addruart, rx diff --git a/arch/arm/kernel/elf.c b/arch/arm/kernel/elf.c index 950391f..d4a0da1 100644 --- a/arch/arm/kernel/elf.c +++ b/arch/arm/kernel/elf.c @@ -78,15 +78,6 @@ int arm_elf_read_implies_exec(const struct elf32_hdr *x, int executable_stack) return 1; if (cpu_architecture() < CPU_ARCH_ARMv6) return 1; -#if !defined(CONFIG_AEABI) || defined(CONFIG_OABI_COMPAT) - /* - * If we have support for OABI programs, we can never allow NX - * support - our signal syscall restart mechanism relies upon - * being able to execute code placed on the user stack. - */ - return 1; -#else return 0; -#endif } EXPORT_SYMBOL(arm_elf_read_implies_exec); diff --git a/arch/arm/kernel/entry-armv.S b/arch/arm/kernel/entry-armv.S index d2903e3..6c5cf36 100644 --- a/arch/arm/kernel/entry-armv.S +++ b/arch/arm/kernel/entry-armv.S @@ -957,9 +957,7 @@ kuser_cmpxchg_fixup: #else -#ifdef CONFIG_SMP - mcr p15, 0, r0, c7, c10, 5 @ dmb -#endif + smp_dmb 1: ldrex r3, [r2] subs r3, r3, r0 strexeq r3, r1, [r2] diff --git a/arch/arm/kernel/process.c b/arch/arm/kernel/process.c index 6730413..ba2adef 100644 --- a/arch/arm/kernel/process.c +++ b/arch/arm/kernel/process.c @@ -212,7 +212,8 @@ void __show_regs(struct pt_regs *regs) char buf[64]; printk("CPU: %d %s (%s %.*s)\n", - smp_processor_id(), print_tainted(), init_utsname()->release, + raw_smp_processor_id(), print_tainted(), + init_utsname()->release, (int)strcspn(init_utsname()->version, " "), init_utsname()->version); print_symbol("PC is at %s\n", instruction_pointer(regs)); diff --git a/arch/arm/mach-davinci/include/mach/keyscan.h b/arch/arm/mach-davinci/include/mach/keyscan.h index b4e21a2..7a560e0 100644 --- a/arch/arm/mach-davinci/include/mach/keyscan.h +++ b/arch/arm/mach-davinci/include/mach/keyscan.h @@ -29,6 +29,7 @@ enum davinci_matrix_types { }; struct davinci_ks_platform_data { + int (*device_enable)(struct device *dev); unsigned short *keymap; u32 keymapsize; u8 rep:1; diff --git a/arch/arm/mach-gemini/include/mach/uncompress.h b/arch/arm/mach-gemini/include/mach/uncompress.h index 59c5df7..5483f61 100644 --- a/arch/arm/mach-gemini/include/mach/uncompress.h +++ b/arch/arm/mach-gemini/include/mach/uncompress.h @@ -30,7 +30,9 @@ static inline void putc(char c) UART[UART_TX] = c; } -#define flush() do { } while (0) +static inline void flush(void) +{ +} /* * nothing to do diff --git a/arch/arm/mach-kirkwood/rd88f6192-nas-setup.c b/arch/arm/mach-kirkwood/rd88f6192-nas-setup.c index 8bf4153..3bf6304 100644 --- a/arch/arm/mach-kirkwood/rd88f6192-nas-setup.c +++ b/arch/arm/mach-kirkwood/rd88f6192-nas-setup.c @@ -13,6 +13,7 @@ #include <linux/platform_device.h> #include <linux/ata_platform.h> #include <linux/mv643xx_eth.h> +#include <linux/gpio.h> #include <linux/spi/flash.h> #include <linux/spi/spi.h> #include <linux/spi/orion_spi.h> @@ -53,6 +54,11 @@ static void __init rd88f6192_init(void) */ kirkwood_init(); + orion_gpio_set_valid(RD88F6192_GPIO_USB_VBUS, 1); + if (gpio_request(RD88F6192_GPIO_USB_VBUS, "USB VBUS") != 0 || + gpio_direction_output(RD88F6192_GPIO_USB_VBUS, 1) != 0) + pr_err("RD-88F6192-NAS: failed to setup USB VBUS GPIO\n"); + kirkwood_ehci_init(); kirkwood_ge00_init(&rd88f6192_ge00_data); kirkwood_sata_init(&rd88f6192_sata_data); diff --git a/arch/arm/mach-lh7a40x/clocks.c b/arch/arm/mach-lh7a40x/clocks.c index fcaf876..0651f96 100644 --- a/arch/arm/mach-lh7a40x/clocks.c +++ b/arch/arm/mach-lh7a40x/clocks.c @@ -10,6 +10,8 @@ #include <mach/hardware.h> #include <mach/clocks.h> #include <linux/err.h> +#include <linux/device.h> +#include <linux/string.h> struct module; diff --git a/arch/arm/mach-mx25/clock.c b/arch/arm/mach-mx25/clock.c index 6e838b8..6acc88b 100644 --- a/arch/arm/mach-mx25/clock.c +++ b/arch/arm/mach-mx25/clock.c @@ -119,6 +119,11 @@ static unsigned long get_rate_nfc(struct clk *clk) return get_rate_per(8); } +static unsigned long get_rate_gpt(struct clk *clk) +{ + return get_rate_per(5); +} + static unsigned long get_rate_otg(struct clk *clk) { return 48000000; /* FIXME */ @@ -144,7 +149,7 @@ static void clk_cgcr_disable(struct clk *clk) __raw_writel(reg, clk->enable_reg); } -#define DEFINE_CLOCK(name, i, er, es, gr, sr) \ +#define DEFINE_CLOCK(name, i, er, es, gr, sr, s) \ static struct clk name = { \ .id = i, \ .enable_reg = CRM_BASE + er, \ @@ -153,27 +158,30 @@ static void clk_cgcr_disable(struct clk *clk) .set_rate = sr, \ .enable = clk_cgcr_enable, \ .disable = clk_cgcr_disable, \ + .secondary = s, \ } -DEFINE_CLOCK(gpt_clk, 0, CCM_CGCR0, 5, get_rate_ipg, NULL); -DEFINE_CLOCK(cspi1_clk, 0, CCM_CGCR1, 5, get_rate_ipg, NULL); -DEFINE_CLOCK(cspi2_clk, 0, CCM_CGCR1, 6, get_rate_ipg, NULL); -DEFINE_CLOCK(cspi3_clk, 0, CCM_CGCR1, 7, get_rate_ipg, NULL); -DEFINE_CLOCK(uart1_clk, 0, CCM_CGCR2, 14, get_rate_uart, NULL); -DEFINE_CLOCK(uart2_clk, 0, CCM_CGCR2, 15, get_rate_uart, NULL); -DEFINE_CLOCK(uart3_clk, 0, CCM_CGCR2, 16, get_rate_uart, NULL); -DEFINE_CLOCK(uart4_clk, 0, CCM_CGCR2, 17, get_rate_uart, NULL); -DEFINE_CLOCK(uart5_clk, 0, CCM_CGCR2, 18, get_rate_uart, NULL); -DEFINE_CLOCK(nfc_clk, 0, CCM_CGCR0, 8, get_rate_nfc, NULL); -DEFINE_CLOCK(usbotg_clk, 0, CCM_CGCR0, 28, get_rate_otg, NULL); -DEFINE_CLOCK(pwm1_clk, 0, CCM_CGCR1, 31, get_rate_ipg, NULL); -DEFINE_CLOCK(pwm2_clk, 0, CCM_CGCR2, 0, get_rate_ipg, NULL); -DEFINE_CLOCK(pwm3_clk, 0, CCM_CGCR2, 1, get_rate_ipg, NULL); -DEFINE_CLOCK(pwm4_clk, 0, CCM_CGCR2, 2, get_rate_ipg, NULL); -DEFINE_CLOCK(kpp_clk, 0, CCM_CGCR1, 28, get_rate_ipg, NULL); -DEFINE_CLOCK(tsc_clk, 0, CCM_CGCR2, 13, get_rate_ipg, NULL); -DEFINE_CLOCK(i2c_clk, 0, CCM_CGCR0, 6, get_rate_i2c, NULL); -DEFINE_CLOCK(fec_clk, 0, CCM_CGCR0, 23, get_rate_ipg, NULL); +DEFINE_CLOCK(gpt_clk, 0, CCM_CGCR0, 5, get_rate_gpt, NULL, NULL); +DEFINE_CLOCK(uart_per_clk, 0, CCM_CGCR0, 15, get_rate_uart, NULL, NULL); +DEFINE_CLOCK(cspi1_clk, 0, CCM_CGCR1, 5, get_rate_ipg, NULL, NULL); +DEFINE_CLOCK(cspi2_clk, 0, CCM_CGCR1, 6, get_rate_ipg, NULL, NULL); +DEFINE_CLOCK(cspi3_clk, 0, CCM_CGCR1, 7, get_rate_ipg, NULL, NULL); +DEFINE_CLOCK(fec_ahb_clk, 0, CCM_CGCR0, 23, NULL, NULL, NULL); +DEFINE_CLOCK(uart1_clk, 0, CCM_CGCR2, 14, get_rate_uart, NULL, &uart_per_clk); +DEFINE_CLOCK(uart2_clk, 0, CCM_CGCR2, 15, get_rate_uart, NULL, &uart_per_clk); +DEFINE_CLOCK(uart3_clk, 0, CCM_CGCR2, 16, get_rate_uart, NULL, &uart_per_clk); +DEFINE_CLOCK(uart4_clk, 0, CCM_CGCR2, 17, get_rate_uart, NULL, &uart_per_clk); +DEFINE_CLOCK(uart5_clk, 0, CCM_CGCR2, 18, get_rate_uart, NULL, &uart_per_clk); +DEFINE_CLOCK(nfc_clk, 0, CCM_CGCR0, 8, get_rate_nfc, NULL, NULL); +DEFINE_CLOCK(usbotg_clk, 0, CCM_CGCR0, 28, get_rate_otg, NULL, NULL); +DEFINE_CLOCK(pwm1_clk, 0, CCM_CGCR1, 31, get_rate_ipg, NULL, NULL); +DEFINE_CLOCK(pwm2_clk, 0, CCM_CGCR2, 0, get_rate_ipg, NULL, NULL); +DEFINE_CLOCK(pwm3_clk, 0, CCM_CGCR2, 1, get_rate_ipg, NULL, NULL); +DEFINE_CLOCK(pwm4_clk, 0, CCM_CGCR2, 2, get_rate_ipg, NULL, NULL); +DEFINE_CLOCK(kpp_clk, 0, CCM_CGCR1, 28, get_rate_ipg, NULL, NULL); +DEFINE_CLOCK(tsc_clk, 0, CCM_CGCR2, 13, get_rate_ipg, NULL, NULL); +DEFINE_CLOCK(i2c_clk, 0, CCM_CGCR0, 6, get_rate_i2c, NULL, NULL); +DEFINE_CLOCK(fec_clk, 0, CCM_CGCR1, 15, get_rate_ipg, NULL, &fec_ahb_clk); #define _REGISTER_CLOCK(d, n, c) \ { \ @@ -208,13 +216,21 @@ static struct clk_lookup lookups[] = { _REGISTER_CLOCK("fec.0", NULL, fec_clk) }; -int __init mx25_clocks_init(unsigned long fref) +int __init mx25_clocks_init(void) { int i; for (i = 0; i < ARRAY_SIZE(lookups); i++) clkdev_add(&lookups[i]); + /* Turn off all clocks except the ones we need to survive, namely: + * EMI, GPIO1-3 (CCM_CGCR1[18:16]), GPT1, IOMUXC (CCM_CGCR1[27]), IIM, + * SCC + */ + __raw_writel((1 << 19), CRM_BASE + CCM_CGCR0); + __raw_writel((0xf << 16) | (3 << 26), CRM_BASE + CCM_CGCR1); + __raw_writel((1 << 5), CRM_BASE + CCM_CGCR2); + mxc_timer_init(&gpt_clk, MX25_IO_ADDRESS(MX25_GPT1_BASE_ADDR), 54); return 0; diff --git a/arch/arm/mach-mx25/mx25pdk.c b/arch/arm/mach-mx25/mx25pdk.c index 921bc99..6f06089 100644 --- a/arch/arm/mach-mx25/mx25pdk.c +++ b/arch/arm/mach-mx25/mx25pdk.c @@ -91,7 +91,7 @@ static void __init mx25pdk_init(void) static void __init mx25pdk_timer_init(void) { - mx25_clocks_init(26000000); + mx25_clocks_init(); } static struct sys_timer mx25pdk_timer = { diff --git a/arch/arm/mach-mx3/mx31ads.c b/arch/arm/mach-mx3/mx31ads.c index 3e7bafa..938c549 100644 --- a/arch/arm/mach-mx3/mx31ads.c +++ b/arch/arm/mach-mx3/mx31ads.c @@ -173,6 +173,7 @@ static void expio_unmask_irq(u32 irq) } static struct irq_chip expio_irq_chip = { + .name = "EXPIO(CPLD)", .ack = expio_ack_irq, .mask = expio_mask_irq, .unmask = expio_unmask_irq, @@ -302,6 +303,7 @@ static struct regulator_init_data ldo1_data = { .min_uV = 2800000, .max_uV = 2800000, .valid_modes_mask = REGULATOR_MODE_NORMAL, + .valid_ops_mask = REGULATOR_CHANGE_STATUS, .apply_uV = 1, }, }; @@ -322,6 +324,7 @@ static struct regulator_init_data ldo2_data = { .min_uV = 3300000, .max_uV = 3300000, .valid_modes_mask = REGULATOR_MODE_NORMAL, + .valid_ops_mask = REGULATOR_CHANGE_STATUS, .apply_uV = 1, }, .num_consumer_supplies = ARRAY_SIZE(ldo2_consumers), @@ -459,6 +462,7 @@ static int mx31_wm8350_init(struct wm8350 *wm8350) static struct wm8350_platform_data __initdata mx31_wm8350_pdata = { .init = mx31_wm8350_init, + .irq_base = MXC_BOARD_IRQ_START + MXC_MAX_EXP_IO_LINES, }; #endif diff --git a/arch/arm/mach-omap1/clock.c b/arch/arm/mach-omap1/clock.c index 2ba9ab95..04f1d29 100644 --- a/arch/arm/mach-omap1/clock.c +++ b/arch/arm/mach-omap1/clock.c @@ -214,8 +214,8 @@ int omap1_select_table_rate(struct clk *clk, unsigned long rate) struct mpu_rate * ptr; unsigned long dpll1_rate, ref_rate; - dpll1_rate = clk_get_rate(ck_dpll1_p); - ref_rate = clk_get_rate(ck_ref_p); + dpll1_rate = ck_dpll1_p->rate; + ref_rate = ck_ref_p->rate; for (ptr = omap1_rate_table; ptr->rate; ptr++) { if (ptr->xtal != ref_rate) @@ -306,7 +306,7 @@ long omap1_round_to_table_rate(struct clk *clk, unsigned long rate) long highest_rate; unsigned long ref_rate; - ref_rate = clk_get_rate(ck_ref_p); + ref_rate = ck_ref_p->rate; highest_rate = -EINVAL; diff --git a/arch/arm/mach-omap1/clock_data.c b/arch/arm/mach-omap1/clock_data.c index ab995a9..65e7b5b 100644 --- a/arch/arm/mach-omap1/clock_data.c +++ b/arch/arm/mach-omap1/clock_data.c @@ -599,7 +599,7 @@ static struct clk i2c_ick = { static struct omap_clk omap_clks[] = { /* non-ULPD clocks */ CLK(NULL, "ck_ref", &ck_ref, CK_16XX | CK_1510 | CK_310 | CK_7XX), - CLK(NULL, "ck_dpll1", &ck_dpll1, CK_16XX | CK_1510 | CK_310), + CLK(NULL, "ck_dpll1", &ck_dpll1, CK_16XX | CK_1510 | CK_310 | CK_7XX), /* CK_GEN1 clocks */ CLK(NULL, "ck_dpll1out", &ck_dpll1out.clk, CK_16XX), CLK(NULL, "ck_sossi", &sossi_ck, CK_16XX), @@ -627,7 +627,7 @@ static struct omap_clk omap_clks[] = { CLK(NULL, "tc2_ck", &tc2_ck, CK_16XX), CLK(NULL, "dma_ck", &dma_ck, CK_16XX | CK_1510 | CK_310), CLK(NULL, "dma_lcdfree_ck", &dma_lcdfree_ck, CK_16XX), - CLK(NULL, "api_ck", &api_ck.clk, CK_16XX | CK_1510 | CK_310), + CLK(NULL, "api_ck", &api_ck.clk, CK_16XX | CK_1510 | CK_310 | CK_7XX), CLK(NULL, "lb_ck", &lb_ck.clk, CK_1510 | CK_310), CLK(NULL, "rhea1_ck", &rhea1_ck, CK_16XX), CLK(NULL, "rhea2_ck", &rhea2_ck, CK_16XX), @@ -658,6 +658,10 @@ static struct omap_clk omap_clks[] = { CLK("i2c_omap.1", "fck", &i2c_fck, CK_16XX | CK_1510 | CK_310 | CK_7XX), CLK("i2c_omap.1", "ick", &i2c_ick, CK_16XX), CLK("i2c_omap.1", "ick", &dummy_ck, CK_1510 | CK_310 | CK_7XX), + CLK("omap1_spi100k.1", "fck", &dummy_ck, CK_7XX), + CLK("omap1_spi100k.1", "ick", &dummy_ck, CK_7XX), + CLK("omap1_spi100k.2", "fck", &dummy_ck, CK_7XX), + CLK("omap1_spi100k.2", "ick", &dummy_ck, CK_7XX), CLK("omap_uwire", "fck", &armxor_ck.clk, CK_16XX | CK_1510 | CK_310), CLK("omap-mcbsp.1", "ick", &dspper_ck, CK_16XX), CLK("omap-mcbsp.1", "ick", &dummy_ck, CK_1510 | CK_310), @@ -674,7 +678,7 @@ static struct omap_clk omap_clks[] = { * init */ -static struct clk_functions omap1_clk_functions __initdata = { +static struct clk_functions omap1_clk_functions = { .clk_enable = omap1_clk_enable, .clk_disable = omap1_clk_disable, .clk_round_rate = omap1_clk_round_rate, diff --git a/arch/arm/mach-omap1/devices.c b/arch/arm/mach-omap1/devices.c index 23ded2d..a2d07aa 100644 --- a/arch/arm/mach-omap1/devices.c +++ b/arch/arm/mach-omap1/devices.c @@ -14,6 +14,7 @@ #include <linux/init.h> #include <linux/platform_device.h> #include <linux/io.h> +#include <linux/spi/spi.h> #include <mach/hardware.h> #include <asm/mach/map.h> @@ -23,6 +24,7 @@ #include <plat/mux.h> #include <mach/gpio.h> #include <plat/mmc.h> +#include <plat/omap7xx.h> /*-------------------------------------------------------------------------*/ @@ -196,6 +198,38 @@ void __init omap1_init_mmc(struct omap_mmc_platform_data **mmc_data, /*-------------------------------------------------------------------------*/ +/* OMAP7xx SPI support */ +#if defined(CONFIG_SPI_OMAP_100K) || defined(CONFIG_SPI_OMAP_100K_MODULE) + +struct platform_device omap_spi1 = { + .name = "omap1_spi100k", + .id = 1, +}; + +struct platform_device omap_spi2 = { + .name = "omap1_spi100k", + .id = 2, +}; + +static void omap_init_spi100k(void) +{ + omap_spi1.dev.platform_data = ioremap(OMAP7XX_SPI1_BASE, 0x7ff); + if (omap_spi1.dev.platform_data) + platform_device_register(&omap_spi1); + + omap_spi2.dev.platform_data = ioremap(OMAP7XX_SPI2_BASE, 0x7ff); + if (omap_spi2.dev.platform_data) + platform_device_register(&omap_spi2); +} + +#else +static inline void omap_init_spi100k(void) +{ +} +#endif + +/*-------------------------------------------------------------------------*/ + #if defined(CONFIG_OMAP_STI) #define OMAP1_STI_BASE 0xfffea000 @@ -263,6 +297,7 @@ static int __init omap1_init_devices(void) omap_init_mbox(); omap_init_rtc(); + omap_init_spi100k(); omap_init_sti(); return 0; diff --git a/arch/arm/mach-omap1/mux.c b/arch/arm/mach-omap1/mux.c index 07212cc..8434137 100644 --- a/arch/arm/mach-omap1/mux.c +++ b/arch/arm/mach-omap1/mux.c @@ -62,6 +62,14 @@ MUX_CFG_7XX("MMC_7XX_DAT0", 2, 17, 0, 16, 1, 0) /* I2C interface */ MUX_CFG_7XX("I2C_7XX_SCL", 5, 1, 0, 0, 1, 0) MUX_CFG_7XX("I2C_7XX_SDA", 5, 5, 0, 0, 1, 0) + +/* SPI pins */ +MUX_CFG_7XX("SPI_7XX_1", 6, 5, 4, 4, 1, 0) +MUX_CFG_7XX("SPI_7XX_2", 6, 9, 4, 8, 1, 0) +MUX_CFG_7XX("SPI_7XX_3", 6, 13, 4, 12, 1, 0) +MUX_CFG_7XX("SPI_7XX_4", 6, 17, 4, 16, 1, 0) +MUX_CFG_7XX("SPI_7XX_5", 8, 25, 0, 24, 0, 0) +MUX_CFG_7XX("SPI_7XX_6", 9, 5, 0, 4, 0, 0) }; #define OMAP7XX_PINS_SZ ARRAY_SIZE(omap7xx_pins) #else diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig index 10eafa7..606bf04 100644 --- a/arch/arm/mach-omap2/Kconfig +++ b/arch/arm/mach-omap2/Kconfig @@ -80,6 +80,7 @@ config MACH_OVERO config MACH_OMAP3EVM bool "OMAP 3530 EVM board" depends on ARCH_OMAP3 && ARCH_OMAP34XX + select OMAP_PACKAGE_CBB config MACH_OMAP3517EVM bool "OMAP3517/ AM3517 EVM board" diff --git a/arch/arm/mach-omap2/board-zoom-peripherals.c b/arch/arm/mach-omap2/board-zoom-peripherals.c index 8dd277c..1e3dfb6 100755 --- a/arch/arm/mach-omap2/board-zoom-peripherals.c +++ b/arch/arm/mach-omap2/board-zoom-peripherals.c @@ -63,21 +63,21 @@ static int board_keymap[] = { KEY(5, 1, KEY_H), KEY(5, 2, KEY_J), KEY(5, 3, KEY_F3), + KEY(5, 4, KEY_UNKNOWN), KEY(5, 5, KEY_VOLUMEDOWN), KEY(5, 6, KEY_M), - KEY(5, 7, KEY_ENTER), + KEY(5, 7, KEY_RIGHT), KEY(6, 0, KEY_Q), KEY(6, 1, KEY_A), KEY(6, 2, KEY_N), KEY(6, 3, KEY_BACKSPACE), KEY(6, 6, KEY_P), - KEY(6, 7, KEY_SELECT), + KEY(6, 7, KEY_UP), KEY(7, 0, KEY_PROG1), /*MACRO 1 <User defined> */ KEY(7, 1, KEY_PROG2), /*MACRO 2 <User defined> */ KEY(7, 2, KEY_PROG3), /*MACRO 3 <User defined> */ KEY(7, 3, KEY_PROG4), /*MACRO 4 <User defined> */ - KEY(7, 5, KEY_RIGHT), - KEY(7, 6, KEY_UP), + KEY(7, 6, KEY_SELECT), KEY(7, 7, KEY_DOWN) }; diff --git a/arch/arm/mach-omap2/clock2xxx.c b/arch/arm/mach-omap2/clock2xxx.c index d0e3fb7..5420356 100644 --- a/arch/arm/mach-omap2/clock2xxx.c +++ b/arch/arm/mach-omap2/clock2xxx.c @@ -449,40 +449,78 @@ int omap2_select_table_rate(struct clk *clk, unsigned long rate) #ifdef CONFIG_CPU_FREQ /* * Walk PRCM rate table and fillout cpufreq freq_table + * XXX This should be replaced by an OPP layer in the near future */ -static struct cpufreq_frequency_table freq_table[ARRAY_SIZE(rate_table)]; +static struct cpufreq_frequency_table *freq_table; void omap2_clk_init_cpufreq_table(struct cpufreq_frequency_table **table) { - struct prcm_config *prcm; + const struct prcm_config *prcm; + long sys_ck_rate; int i = 0; + int tbl_sz = 0; + + sys_ck_rate = clk_get_rate(sclk); for (prcm = rate_table; prcm->mpu_speed; prcm++) { if (!(prcm->flags & cpu_mask)) continue; - if (prcm->xtal_speed != sys_ck.rate) + if (prcm->xtal_speed != sys_ck_rate) continue; /* don't put bypass rates in table */ if (prcm->dpll_speed == prcm->xtal_speed) continue; - freq_table[i].index = i; - freq_table[i].frequency = prcm->mpu_speed / 1000; - i++; + tbl_sz++; } - if (i == 0) { - printk(KERN_WARNING "%s: failed to initialize frequency " - "table\n", __func__); + /* + * XXX Ensure that we're doing what CPUFreq expects for this error + * case and the following one + */ + if (tbl_sz == 0) { + pr_warning("%s: no matching entries in rate_table\n", + __func__); + return; + } + + /* Include the CPUFREQ_TABLE_END terminator entry */ + tbl_sz++; + + freq_table = kzalloc(sizeof(struct cpufreq_frequency_table) * tbl_sz, + GFP_ATOMIC); + if (!freq_table) { + pr_err("%s: could not kzalloc frequency table\n", __func__); return; } + for (prcm = rate_table; prcm->mpu_speed; prcm++) { + if (!(prcm->flags & cpu_mask)) + continue; + if (prcm->xtal_speed != sys_ck_rate) + continue; + + /* don't put bypass rates in table */ + if (prcm->dpll_speed == prcm->xtal_speed) + continue; + + freq_table[i].index = i; + freq_table[i].frequency = prcm->mpu_speed / 1000; + i++; + } + freq_table[i].index = i; freq_table[i].frequency = CPUFREQ_TABLE_END; *table = &freq_table[0]; } + +void omap2_clk_exit_cpufreq_table(struct cpufreq_frequency_table **table) +{ + kfree(freq_table); +} + #endif struct clk_functions omap2_clk_functions = { @@ -494,6 +532,7 @@ struct clk_functions omap2_clk_functions = { .clk_disable_unused = omap2_clk_disable_unused, #ifdef CONFIG_CPU_FREQ .clk_init_cpufreq_table = omap2_clk_init_cpufreq_table, + .clk_exit_cpufreq_table = omap2_clk_exit_cpufreq_table, #endif }; diff --git a/arch/arm/mach-omap2/clock34xx.c b/arch/arm/mach-omap2/clock34xx.c index ded3236..d4217b9 100644 --- a/arch/arm/mach-omap2/clock34xx.c +++ b/arch/arm/mach-omap2/clock34xx.c @@ -34,7 +34,6 @@ #include <asm/div64.h> #include <asm/clkdev.h> -#include <plat/sdrc.h> #include "clock.h" #include "clock34xx.h" #include "sdrc.h" diff --git a/arch/arm/mach-omap2/clock34xx_data.c b/arch/arm/mach-omap2/clock34xx_data.c index 8bdcc9cc..74930e3 100644 --- a/arch/arm/mach-omap2/clock34xx_data.c +++ b/arch/arm/mach-omap2/clock34xx_data.c @@ -671,7 +671,6 @@ static struct clk dpll4_m3x2_ck = { .name = "dpll4_m3x2_ck", .ops = &clkops_omap2_dflt_wait, .parent = &dpll4_m3_ck, - .init = &omap2_init_clksel_parent, .enable_reg = OMAP_CM_REGADDR(PLL_MOD, CM_CLKEN), .enable_bit = OMAP3430_PWRDN_TV_SHIFT, .flags = INVERT_ENABLE, @@ -776,6 +775,8 @@ static struct clk dpll4_m5_ck = { .clksel_mask = OMAP3430_CLKSEL_CAM_MASK, .clksel = div16_dpll4_clksel, .clkdm_name = "dpll4_clkdm", + .set_rate = &omap2_clksel_set_rate, + .round_rate = &omap2_clksel_round_rate, .recalc = &omap2_clksel_recalc, }; @@ -809,7 +810,6 @@ static struct clk dpll4_m6x2_ck = { .name = "dpll4_m6x2_ck", .ops = &clkops_omap2_dflt_wait, .parent = &dpll4_m6_ck, - .init = &omap2_init_clksel_parent, .enable_reg = OMAP_CM_REGADDR(PLL_MOD, CM_CLKEN), .enable_bit = OMAP3430_PWRDN_EMU_PERIPH_SHIFT, .flags = INVERT_ENABLE, @@ -1045,7 +1045,6 @@ static struct clk iva2_ck = { .name = "iva2_ck", .ops = &clkops_omap2_dflt_wait, .parent = &dpll2_m2_ck, - .init = &omap2_init_clksel_parent, .enable_reg = OMAP_CM_REGADDR(OMAP3430_IVA2_MOD, CM_FCLKEN), .enable_bit = OMAP3430_CM_FCLKEN_IVA2_EN_IVA2_SHIFT, .clkdm_name = "iva2_clkdm", @@ -1119,7 +1118,6 @@ static struct clk gfx_l3_ck = { .name = "gfx_l3_ck", .ops = &clkops_omap2_dflt_wait, .parent = &l3_ick, - .init = &omap2_init_clksel_parent, .enable_reg = OMAP_CM_REGADDR(GFX_MOD, CM_ICLKEN), .enable_bit = OMAP_EN_GFX_SHIFT, .recalc = &followparent_recalc, @@ -1500,6 +1498,7 @@ static struct clk uart2_fck = { .parent = &core_48m_fck, .enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_FCLKEN1), .enable_bit = OMAP3430_EN_UART2_SHIFT, + .clkdm_name = "core_l4_clkdm", .recalc = &followparent_recalc, }; @@ -1509,6 +1508,7 @@ static struct clk uart1_fck = { .parent = &core_48m_fck, .enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_FCLKEN1), .enable_bit = OMAP3430_EN_UART1_SHIFT, + .clkdm_name = "core_l4_clkdm", .recalc = &followparent_recalc, }; @@ -2745,7 +2745,7 @@ static struct clk mcbsp4_ick = { }; static const struct clksel mcbsp_234_clksel[] = { - { .parent = &core_96m_fck, .rates = common_mcbsp_96m_rates }, + { .parent = &per_96m_fck, .rates = common_mcbsp_96m_rates }, { .parent = &mcbsp_clks, .rates = common_mcbsp_mcbsp_rates }, { .parent = NULL } }; diff --git a/arch/arm/mach-omap2/clock44xx_data.c b/arch/arm/mach-omap2/clock44xx_data.c index 2210e22..9d882bc 100644 --- a/arch/arm/mach-omap2/clock44xx_data.c +++ b/arch/arm/mach-omap2/clock44xx_data.c @@ -346,37 +346,37 @@ static struct clk aess_fclk = { }; static const struct clksel_rate div31_1to31_rates[] = { - { .div = 1, .val = 0, .flags = RATE_IN_4430 }, - { .div = 2, .val = 1, .flags = RATE_IN_4430 }, - { .div = 3, .val = 2, .flags = RATE_IN_4430 }, - { .div = 4, .val = 3, .flags = RATE_IN_4430 }, - { .div = 5, .val = 4, .flags = RATE_IN_4430 }, - { .div = 6, .val = 5, .flags = RATE_IN_4430 }, - { .div = 7, .val = 6, .flags = RATE_IN_4430 }, - { .div = 8, .val = 7, .flags = RATE_IN_4430 }, - { .div = 9, .val = 8, .flags = RATE_IN_4430 }, - { .div = 10, .val = 9, .flags = RATE_IN_4430 }, - { .div = 11, .val = 10, .flags = RATE_IN_4430 }, - { .div = 12, .val = 11, .flags = RATE_IN_4430 }, - { .div = 13, .val = 12, .flags = RATE_IN_4430 }, - { .div = 14, .val = 13, .flags = RATE_IN_4430 }, - { .div = 15, .val = 14, .flags = RATE_IN_4430 }, - { .div = 16, .val = 15, .flags = RATE_IN_4430 }, - { .div = 17, .val = 16, .flags = RATE_IN_4430 }, - { .div = 18, .val = 17, .flags = RATE_IN_4430 }, - { .div = 19, .val = 18, .flags = RATE_IN_4430 }, - { .div = 20, .val = 19, .flags = RATE_IN_4430 }, - { .div = 21, .val = 20, .flags = RATE_IN_4430 }, - { .div = 22, .val = 21, .flags = RATE_IN_4430 }, - { .div = 23, .val = 22, .flags = RATE_IN_4430 }, - { .div = 24, .val = 23, .flags = RATE_IN_4430 }, - { .div = 25, .val = 24, .flags = RATE_IN_4430 }, - { .div = 26, .val = 25, .flags = RATE_IN_4430 }, - { .div = 27, .val = 26, .flags = RATE_IN_4430 }, - { .div = 28, .val = 27, .flags = RATE_IN_4430 }, - { .div = 29, .val = 28, .flags = RATE_IN_4430 }, - { .div = 30, .val = 29, .flags = RATE_IN_4430 }, - { .div = 31, .val = 30, .flags = RATE_IN_4430 }, + { .div = 1, .val = 1, .flags = RATE_IN_4430 }, + { .div = 2, .val = 2, .flags = RATE_IN_4430 }, + { .div = 3, .val = 3, .flags = RATE_IN_4430 }, + { .div = 4, .val = 4, .flags = RATE_IN_4430 }, + { .div = 5, .val = 5, .flags = RATE_IN_4430 }, + { .div = 6, .val = 6, .flags = RATE_IN_4430 }, + { .div = 7, .val = 7, .flags = RATE_IN_4430 }, + { .div = 8, .val = 8, .flags = RATE_IN_4430 }, + { .div = 9, .val = 9, .flags = RATE_IN_4430 }, + { .div = 10, .val = 10, .flags = RATE_IN_4430 }, + { .div = 11, .val = 11, .flags = RATE_IN_4430 }, + { .div = 12, .val = 12, .flags = RATE_IN_4430 }, + { .div = 13, .val = 13, .flags = RATE_IN_4430 }, + { .div = 14, .val = 14, .flags = RATE_IN_4430 }, + { .div = 15, .val = 15, .flags = RATE_IN_4430 }, + { .div = 16, .val = 16, .flags = RATE_IN_4430 }, + { .div = 17, .val = 17, .flags = RATE_IN_4430 }, + { .div = 18, .val = 18, .flags = RATE_IN_4430 }, + { .div = 19, .val = 19, .flags = RATE_IN_4430 }, + { .div = 20, .val = 20, .flags = RATE_IN_4430 }, + { .div = 21, .val = 21, .flags = RATE_IN_4430 }, + { .div = 22, .val = 22, .flags = RATE_IN_4430 }, + { .div = 23, .val = 23, .flags = RATE_IN_4430 }, + { .div = 24, .val = 24, .flags = RATE_IN_4430 }, + { .div = 25, .val = 25, .flags = RATE_IN_4430 }, + { .div = 26, .val = 26, .flags = RATE_IN_4430 }, + { .div = 27, .val = 27, .flags = RATE_IN_4430 }, + { .div = 28, .val = 28, .flags = RATE_IN_4430 }, + { .div = 29, .val = 29, .flags = RATE_IN_4430 }, + { .div = 30, .val = 30, .flags = RATE_IN_4430 }, + { .div = 31, .val = 31, .flags = RATE_IN_4430 }, { .div = 0 }, }; diff --git a/arch/arm/mach-omap2/clockdomain.c b/arch/arm/mach-omap2/clockdomain.c index 1a45ed1..dd285f0 100644 --- a/arch/arm/mach-omap2/clockdomain.c +++ b/arch/arm/mach-omap2/clockdomain.c @@ -559,7 +559,7 @@ int omap2_clkdm_clk_enable(struct clockdomain *clkdm, struct clk *clk) * downstream clocks for debugging purposes? */ - if (!clkdm || !clk) + if (!clkdm || !clk || !clkdm->clktrctrl_mask) return -EINVAL; if (atomic_inc_return(&clkdm->usecount) > 1) @@ -610,7 +610,7 @@ int omap2_clkdm_clk_disable(struct clockdomain *clkdm, struct clk *clk) * downstream clocks for debugging purposes? */ - if (!clkdm || !clk) + if (!clkdm || !clk || !clkdm->clktrctrl_mask) return -EINVAL; #ifdef DEBUG diff --git a/arch/arm/mach-omap2/cpuidle34xx.c b/arch/arm/mach-omap2/cpuidle34xx.c index a26d6a0..12f0cbf 100644 --- a/arch/arm/mach-omap2/cpuidle34xx.c +++ b/arch/arm/mach-omap2/cpuidle34xx.c @@ -137,7 +137,7 @@ return_sleep_time: local_irq_enable(); local_fiq_enable(); - return (u32)timespec_to_ns(&ts_idle)/1000; + return ts_idle.tv_nsec / NSEC_PER_USEC + ts_idle.tv_sec * USEC_PER_SEC; } /** diff --git a/arch/arm/mach-omap2/gpmc.c b/arch/arm/mach-omap2/gpmc.c index bd8cb59..7027cdc 100644 --- a/arch/arm/mach-omap2/gpmc.c +++ b/arch/arm/mach-omap2/gpmc.c @@ -505,7 +505,7 @@ static void __init gpmc_mem_init(void) void __init gpmc_init(void) { u32 l; - char *ck; + char *ck = NULL; if (cpu_is_omap24xx()) { ck = "core_l3_ck"; @@ -521,6 +521,9 @@ void __init gpmc_init(void) l = OMAP44XX_GPMC_BASE; } + if (WARN_ON(!ck)) + return; + gpmc_l3_clk = clk_get(NULL, ck); if (IS_ERR(gpmc_l3_clk)) { printk(KERN_ERR "Could not get GPMC clock %s\n", ck); @@ -534,6 +537,8 @@ void __init gpmc_init(void) BUG(); } + clk_enable(gpmc_l3_clk); + l = gpmc_read_reg(GPMC_REVISION); printk(KERN_INFO "GPMC revision %d.%d\n", (l >> 4) & 0x0f, l & 0x0f); /* Set smart idle mode and automatic L3 clock gating */ diff --git a/arch/arm/mach-omap2/id.c b/arch/arm/mach-omap2/id.c index a091b53..3d65c50 100644 --- a/arch/arm/mach-omap2/id.c +++ b/arch/arm/mach-omap2/id.c @@ -188,6 +188,8 @@ void __init omap3_check_revision(void) u16 hawkeye; u8 rev; + omap_chip.oc = CHIP_IS_OMAP3430; + /* * We cannot access revision registers on ES1.0. * If the processor type is Cortex-A8 and the revision is 0x0 @@ -196,6 +198,7 @@ void __init omap3_check_revision(void) cpuid = read_cpuid(CPUID_ID); if ((((cpuid >> 4) & 0xfff) == 0xc08) && ((cpuid & 0xf) == 0x0)) { omap_revision = OMAP3430_REV_ES1_0; + omap_chip.oc |= CHIP_IS_OMAP3430ES1; return; } @@ -216,18 +219,28 @@ void __init omap3_check_revision(void) case 0: /* Take care of early samples */ case 1: omap_revision = OMAP3430_REV_ES2_0; + omap_chip.oc |= CHIP_IS_OMAP3430ES2; break; case 2: omap_revision = OMAP3430_REV_ES2_1; + omap_chip.oc |= CHIP_IS_OMAP3430ES2; break; case 3: omap_revision = OMAP3430_REV_ES3_0; + omap_chip.oc |= CHIP_IS_OMAP3430ES3_0; break; case 4: + omap_revision = OMAP3430_REV_ES3_1; + omap_chip.oc |= CHIP_IS_OMAP3430ES3_1; + break; + case 7: /* FALLTHROUGH */ default: /* Use the latest known revision as default */ - omap_revision = OMAP3430_REV_ES3_1; + omap_revision = OMAP3430_REV_ES3_1_2; + + /* REVISIT: Add CHIP_IS_OMAP3430ES3_1_2? */ + omap_chip.oc |= CHIP_IS_OMAP3430ES3_1; } break; case 0xb868: @@ -235,14 +248,18 @@ void __init omap3_check_revision(void) * * Set the device to be OMAP3505 here. Actual device * is identified later based on the features. + * + * REVISIT: AM3505/AM3517 should have their own CHIP_IS */ omap_revision = OMAP3505_REV(rev); + omap_chip.oc |= CHIP_IS_OMAP3430ES3_1; break; case 0xb891: /* FALLTHROUGH */ default: /* Unknown default to latest silicon rev as default*/ omap_revision = OMAP3630_REV_ES1_0; + omap_chip.oc |= CHIP_IS_OMAP3630ES1; } } @@ -360,6 +377,7 @@ void __init omap2_check_revision(void) omap3_check_revision(); omap3_check_features(); omap3_cpuinfo(); + return; } else if (cpu_is_omap44xx()) { omap4_check_revision(); return; @@ -374,27 +392,14 @@ void __init omap2_check_revision(void) if (cpu_is_omap243x()) { /* Currently only supports 2430ES2.1 and 2430-all */ omap_chip.oc |= CHIP_IS_OMAP2430; + return; } else if (cpu_is_omap242x()) { /* Currently only supports 2420ES2.1.1 and 2420-all */ omap_chip.oc |= CHIP_IS_OMAP2420; - } else if (cpu_is_omap3505() || cpu_is_omap3517()) { - omap_chip.oc = CHIP_IS_OMAP3430 | CHIP_IS_OMAP3430ES3_1; - } else if (cpu_is_omap343x()) { - omap_chip.oc = CHIP_IS_OMAP3430; - if (omap_rev() == OMAP3430_REV_ES1_0) - omap_chip.oc |= CHIP_IS_OMAP3430ES1; - else if (omap_rev() >= OMAP3430_REV_ES2_0 && - omap_rev() <= OMAP3430_REV_ES2_1) - omap_chip.oc |= CHIP_IS_OMAP3430ES2; - else if (omap_rev() == OMAP3430_REV_ES3_0) - omap_chip.oc |= CHIP_IS_OMAP3430ES3_0; - else if (omap_rev() == OMAP3430_REV_ES3_1) - omap_chip.oc |= CHIP_IS_OMAP3430ES3_1; - else if (omap_rev() == OMAP3630_REV_ES1_0) - omap_chip.oc |= CHIP_IS_OMAP3630ES1; - } else { - pr_err("Uninitialized omap_chip, please fix!\n"); + return; } + + pr_err("Uninitialized omap_chip, please fix!\n"); } /* diff --git a/arch/arm/mach-omap2/io.c b/arch/arm/mach-omap2/io.c index a8749e8..5a79964 100644 --- a/arch/arm/mach-omap2/io.c +++ b/arch/arm/mach-omap2/io.c @@ -33,7 +33,6 @@ #include <plat/sdrc.h> #include <plat/gpmc.h> #include <plat/serial.h> -#include <plat/mux.h> #include <plat/vram.h> #include "clock.h" @@ -73,21 +72,21 @@ static struct map_desc omap24xx_io_desc[] __initdata = { #ifdef CONFIG_ARCH_OMAP2420 static struct map_desc omap242x_io_desc[] __initdata = { { - .virtual = DSP_MEM_24XX_VIRT, - .pfn = __phys_to_pfn(DSP_MEM_24XX_PHYS), - .length = DSP_MEM_24XX_SIZE, + .virtual = DSP_MEM_2420_VIRT, + .pfn = __phys_to_pfn(DSP_MEM_2420_PHYS), + .length = DSP_MEM_2420_SIZE, .type = MT_DEVICE }, { - .virtual = DSP_IPI_24XX_VIRT, - .pfn = __phys_to_pfn(DSP_IPI_24XX_PHYS), - .length = DSP_IPI_24XX_SIZE, + .virtual = DSP_IPI_2420_VIRT, + .pfn = __phys_to_pfn(DSP_IPI_2420_PHYS), + .length = DSP_IPI_2420_SIZE, .type = MT_DEVICE }, { - .virtual = DSP_MMU_24XX_VIRT, - .pfn = __phys_to_pfn(DSP_MMU_24XX_PHYS), - .length = DSP_MMU_24XX_SIZE, + .virtual = DSP_MMU_2420_VIRT, + .pfn = __phys_to_pfn(DSP_MMU_2420_PHYS), + .length = DSP_MMU_2420_SIZE, .type = MT_DEVICE }, }; diff --git a/arch/arm/mach-omap2/irq.c b/arch/arm/mach-omap2/irq.c index e9bc782..26aeef5 100644 --- a/arch/arm/mach-omap2/irq.c +++ b/arch/arm/mach-omap2/irq.c @@ -194,7 +194,7 @@ void __init omap_init_irq(void) int i; for (i = 0; i < ARRAY_SIZE(irq_banks); i++) { - unsigned long base; + unsigned long base = 0; struct omap_irq_bank *bank = irq_banks + i; if (cpu_is_omap24xx()) @@ -202,6 +202,8 @@ void __init omap_init_irq(void) else if (cpu_is_omap34xx()) base = OMAP34XX_IC_BASE; + BUG_ON(!base); + /* Static mapping, never released */ bank->base_reg = ioremap(base, SZ_4K); if (!bank->base_reg) { @@ -274,4 +276,22 @@ void omap_intc_restore_context(void) } /* MIRs are saved and restore with other PRCM registers */ } + +void omap3_intc_suspend(void) +{ + /* A pending interrupt would prevent OMAP from entering suspend */ + omap_ack_irq(0); +} + +void omap3_intc_prepare_idle(void) +{ + /* Disable autoidle as it can stall interrupt controller */ + intc_bank_write_reg(0, &irq_banks[0], INTC_SYSCONFIG); +} + +void omap3_intc_resume_idle(void) +{ + /* Re-enable autoidle */ + intc_bank_write_reg(1, &irq_banks[0], INTC_SYSCONFIG); +} #endif /* CONFIG_ARCH_OMAP3 */ diff --git a/arch/arm/mach-omap2/mmc-twl4030.c b/arch/arm/mach-omap2/mmc-twl4030.c index 0c3c72d..8afe9dd 100644 --- a/arch/arm/mach-omap2/mmc-twl4030.c +++ b/arch/arm/mach-omap2/mmc-twl4030.c @@ -408,6 +408,7 @@ void __init twl4030_mmc_init(struct twl4030_hsmmc_info *controllers) { struct twl4030_hsmmc_info *c; int nr_hsmmc = ARRAY_SIZE(hsmmc_data); + int i; if (cpu_is_omap2430()) { control_pbias_offset = OMAP243X_CONTROL_PBIAS_LITE; @@ -434,7 +435,7 @@ void __init twl4030_mmc_init(struct twl4030_hsmmc_info *controllers) mmc = kzalloc(sizeof(struct omap_mmc_platform_data), GFP_KERNEL); if (!mmc) { pr_err("Cannot allocate memory for mmc device!\n"); - return; + goto done; } if (c->name) @@ -532,6 +533,10 @@ void __init twl4030_mmc_init(struct twl4030_hsmmc_info *controllers) continue; c->dev = mmc->dev; } + +done: + for (i = 0; i < nr_hsmmc; i++) + kfree(hsmmc_data[i]); } #endif diff --git a/arch/arm/mach-omap2/mux.c b/arch/arm/mach-omap2/mux.c index e071b3f..5fedc50 100644 --- a/arch/arm/mach-omap2/mux.c +++ b/arch/arm/mach-omap2/mux.c @@ -51,7 +51,7 @@ struct omap_mux_entry { static unsigned long mux_phys; static void __iomem *mux_base; -static inline u16 omap_mux_read(u16 reg) +u16 omap_mux_read(u16 reg) { if (cpu_is_omap24xx()) return __raw_readb(mux_base + reg); @@ -59,7 +59,7 @@ static inline u16 omap_mux_read(u16 reg) return __raw_readw(mux_base + reg); } -static inline void omap_mux_write(u16 val, u16 reg) +void omap_mux_write(u16 val, u16 reg) { if (cpu_is_omap24xx()) __raw_writeb(val, mux_base + reg); @@ -67,6 +67,14 @@ static inline void omap_mux_write(u16 val, u16 reg) __raw_writew(val, mux_base + reg); } +void omap_mux_write_array(struct omap_board_mux *board_mux) +{ + while (board_mux->reg_offset != OMAP_MUX_TERMINATOR) { + omap_mux_write(board_mux->value, board_mux->reg_offset); + board_mux++; + } +} + #if defined(CONFIG_ARCH_OMAP24XX) && defined(CONFIG_OMAP_MUX) static struct omap_mux_cfg arch_mux_cfg; @@ -478,7 +486,7 @@ int __init omap_mux_init_signal(char *muxname, int val) static inline void omap_mux_decode(struct seq_file *s, u16 val) { char *flags[OMAP_MUX_MAX_NR_FLAGS]; - char mode[14]; + char mode[sizeof("OMAP_MUX_MODE") + 1]; int i = -1; sprintf(mode, "OMAP_MUX_MODE%d", val & 0x7); @@ -545,6 +553,7 @@ static int omap_mux_dbg_board_show(struct seq_file *s, void *unused) if (!m0_name) continue; + /* REVISIT: Needs to be updated if mode0 names get longer */ for (i = 0; i < OMAP_MUX_DEFNAME_LEN; i++) { if (m0_name[i] == '\0') { m0_def[i] = m0_name[i]; @@ -833,14 +842,6 @@ static void __init omap_mux_set_cmdline_signals(void) kfree(options); } -static void __init omap_mux_set_board_signals(struct omap_board_mux *board_mux) -{ - while (board_mux->reg_offset != OMAP_MUX_TERMINATOR) { - omap_mux_write(board_mux->value, board_mux->reg_offset); - board_mux++; - } -} - static int __init omap_mux_copy_names(struct omap_mux *src, struct omap_mux *dst) { @@ -968,6 +969,13 @@ static void __init omap_mux_init_list(struct omap_mux *superset) } #endif +#if defined(CONFIG_OMAP_MUX) && defined(CONFIG_DEBUG_FS) + if (!superset->muxnames || !superset->muxnames[0]) { + superset++; + continue; + } +#endif + entry = omap_mux_list_add(superset); if (!entry) { printk(KERN_ERR "mux: Could not add entry\n"); @@ -994,14 +1002,19 @@ int __init omap_mux_init(u32 mux_pbase, u32 mux_size, } #ifdef CONFIG_OMAP_MUX - omap_mux_package_fixup(package_subset, superset); - omap_mux_package_init_balls(package_balls, superset); - omap_mux_set_cmdline_signals(); - omap_mux_set_board_signals(board_mux); + if (package_subset) + omap_mux_package_fixup(package_subset, superset); + if (package_balls) + omap_mux_package_init_balls(package_balls, superset); #endif omap_mux_init_list(superset); +#ifdef CONFIG_OMAP_MUX + omap_mux_set_cmdline_signals(); + omap_mux_write_array(board_mux); +#endif + return 0; } diff --git a/arch/arm/mach-omap2/mux.h b/arch/arm/mach-omap2/mux.h index d8b4d5a..f8c2e7a 100644 --- a/arch/arm/mach-omap2/mux.h +++ b/arch/arm/mach-omap2/mux.h @@ -147,6 +147,30 @@ u16 omap_mux_get_gpio(int gpio); void omap_mux_set_gpio(u16 val, int gpio); /** + * omap_mux_read() - read mux register + * @mux_offset: Offset of the mux register + * + */ +u16 omap_mux_read(u16 mux_offset); + +/** + * omap_mux_write() - write mux register + * @val: New mux register value + * @mux_offset: Offset of the mux register + * + * This should be only needed for dynamic remuxing of non-gpio signals. + */ +void omap_mux_write(u16 val, u16 mux_offset); + +/** + * omap_mux_write_array() - write an array of mux registers + * @board_mux: Array of mux registers terminated by MAP_MUX_TERMINATOR + * + * This should be only needed for dynamic remuxing of non-gpio signals. + */ +void omap_mux_write_array(struct omap_board_mux *board_mux); + +/** * omap3_mux_init() - initialize mux system with board specific set * @board_mux: Board specific mux table * @flags: OMAP package type used for the board diff --git a/arch/arm/mach-omap2/mux34xx.c b/arch/arm/mach-omap2/mux34xx.c index 68e0a59..07aa7b3 100644 --- a/arch/arm/mach-omap2/mux34xx.c +++ b/arch/arm/mach-omap2/mux34xx.c @@ -649,6 +649,53 @@ static struct omap_mux __initdata omap3_muxmodes[] = { _OMAP3_MUXENTRY(UART3_TX_IRTX, 166, "uart3_tx_irtx", NULL, NULL, NULL, "gpio_166", NULL, NULL, "safe_mode"), + + /* Only on 3630, see omap36xx_cbp_subset for the signals */ + _OMAP3_MUXENTRY(GPMC_A11, 0, + NULL, NULL, NULL, NULL, + NULL, NULL, NULL, NULL), + _OMAP3_MUXENTRY(SAD2D_MBUSFLAG, 0, + NULL, NULL, NULL, NULL, + NULL, NULL, NULL, NULL), + _OMAP3_MUXENTRY(SAD2D_MREAD, 0, + NULL, NULL, NULL, NULL, + NULL, NULL, NULL, NULL), + _OMAP3_MUXENTRY(SAD2D_MWRITE, 0, + NULL, NULL, NULL, NULL, + NULL, NULL, NULL, NULL), + _OMAP3_MUXENTRY(SAD2D_SBUSFLAG, 0, + NULL, NULL, NULL, NULL, + NULL, NULL, NULL, NULL), + _OMAP3_MUXENTRY(SAD2D_SREAD, 0, + NULL, NULL, NULL, NULL, + NULL, NULL, NULL, NULL), + _OMAP3_MUXENTRY(SAD2D_SWRITE, 0, + NULL, NULL, NULL, NULL, + NULL, NULL, NULL, NULL), + _OMAP3_MUXENTRY(GPMC_A11, 0, + NULL, NULL, NULL, NULL, + NULL, NULL, NULL, NULL), + _OMAP3_MUXENTRY(SAD2D_MCAD28, 0, + NULL, NULL, NULL, NULL, + NULL, NULL, NULL, NULL), + _OMAP3_MUXENTRY(SAD2D_MCAD29, 0, + NULL, NULL, NULL, NULL, + NULL, NULL, NULL, NULL), + _OMAP3_MUXENTRY(SAD2D_MCAD32, 0, + NULL, NULL, NULL, NULL, + NULL, NULL, NULL, NULL), + _OMAP3_MUXENTRY(SAD2D_MCAD33, 0, + NULL, NULL, NULL, NULL, + NULL, NULL, NULL, NULL), + _OMAP3_MUXENTRY(SAD2D_MCAD34, 0, + NULL, NULL, NULL, NULL, + NULL, NULL, NULL, NULL), + _OMAP3_MUXENTRY(SAD2D_MCAD35, 0, + NULL, NULL, NULL, NULL, + NULL, NULL, NULL, NULL), + _OMAP3_MUXENTRY(SAD2D_MCAD36, 0, + NULL, NULL, NULL, NULL, + NULL, NULL, NULL, NULL), { .reg_offset = OMAP_MUX_TERMINATOR }, }; diff --git a/arch/arm/mach-omap2/omap_hwmod.c b/arch/arm/mach-omap2/omap_hwmod.c index d8c8545..478ae58 100644 --- a/arch/arm/mach-omap2/omap_hwmod.c +++ b/arch/arm/mach-omap2/omap_hwmod.c @@ -94,7 +94,8 @@ static int _update_sysc_cache(struct omap_hwmod *oh) oh->_sysc_cache = omap_hwmod_readl(oh, oh->sysconfig->sysc_offs); - oh->_int_flags |= _HWMOD_SYSCONFIG_LOADED; + if (!(oh->sysconfig->sysc_flags & SYSC_NO_CACHE)) + oh->_int_flags |= _HWMOD_SYSCONFIG_LOADED; return 0; } diff --git a/arch/arm/mach-omap2/opp2420_data.c b/arch/arm/mach-omap2/opp2420_data.c index 126a9396..e6dda69 100644 --- a/arch/arm/mach-omap2/opp2420_data.c +++ b/arch/arm/mach-omap2/opp2420_data.c @@ -9,45 +9,47 @@ * The OMAP2 processor can be run at several discrete 'PRCM configurations'. * These configurations are characterized by voltage and speed for clocks. * The device is only validated for certain combinations. One way to express - * these combinations is via the 'ratio's' which the clocks operate with + * these combinations is via the 'ratios' which the clocks operate with * respect to each other. These ratio sets are for a given voltage/DPLL - * setting. All configurations can be described by a DPLL setting and a ratio - * There are 3 ratio sets for the 2430 and X ratio sets for 2420. - * - * 2430 differs from 2420 in that there are no more phase synchronizers used. - * They both have a slightly different clock domain setup. 2420(iva1,dsp) vs - * 2430 (iva2.1, NOdsp, mdm) + * setting. All configurations can be described by a DPLL setting and a ratio. * * XXX Missing voltage data. + * XXX Missing 19.2MHz sys_clk rate sets (needed for N800/N810) * * THe format described in this file is deprecated. Once a reasonable * OPP API exists, the data in this file should be converted to use it. * * This is technically part of the OMAP2xxx clock code. + * + * Considerable work is still needed to fully support dynamic frequency + * changes on OMAP2xxx-series chips. Readers interested in such a + * project are encouraged to review the Maemo Diablo RX-34 and RX-44 + * kernel source at: + * http://repository.maemo.org/pool/diablo/free/k/kernel-source-diablo/ */ #include "opp2xxx.h" #include "sdrc.h" #include "clock.h" -/*------------------------------------------------------------------------- - * Key dividers which make up a PRCM set. Ratio's for a PRCM are mandated. +/* + * Key dividers which make up a PRCM set. Ratios for a PRCM are mandated. * xtal_speed, dpll_speed, mpu_speed, CM_CLKSEL_MPU, * CM_CLKSEL_DSP, CM_CLKSEL_GFX, CM_CLKSEL1_CORE, CM_CLKSEL1_PLL, * CM_CLKSEL2_PLL, CM_CLKSEL_MDM * - * Filling in table based on H4 boards and 2430-SDPs variants available. - * There are quite a few more rates combinations which could be defined. + * Filling in table based on H4 boards available. There are quite a + * few more rate combinations which could be defined. * - * When multiple values are defined the start up will try and choose the - * fastest one. If a 'fast' value is defined, then automatically, the /2 - * one should be included as it can be used. Generally having more that - * one fast set does not make sense, as static timings need to be changed - * to change the set. The exception is the bypass setting which is - * availble for low power bypass. + * When multiple values are defined the start up will try and choose + * the fastest one. If a 'fast' value is defined, then automatically, + * the /2 one should be included as it can be used. Generally having + * more than one fast set does not make sense, as static timings need + * to be changed to change the set. The exception is the bypass + * setting which is available for low power bypass. * * Note: This table needs to be sorted, fastest to slowest. - *-------------------------------------------------------------------------*/ + **/ const struct prcm_config omap2420_rate_table[] = { /* PRCM I - FAST */ {S12M, S660M, S330M, RI_CM_CLKSEL_MPU_VAL, /* 330MHz ARM */ diff --git a/arch/arm/mach-omap2/opp2430_data.c b/arch/arm/mach-omap2/opp2430_data.c index edb8167..1b9596a 100644 --- a/arch/arm/mach-omap2/opp2430_data.c +++ b/arch/arm/mach-omap2/opp2430_data.c @@ -1,5 +1,5 @@ /* - * opp2420_data.c - old-style "OPP" table for OMAP2420 + * opp2430_data.c - old-style "OPP" table for OMAP2430 * * Copyright (C) 2005-2009 Texas Instruments, Inc. * Copyright (C) 2004-2009 Nokia Corporation @@ -9,16 +9,16 @@ * The OMAP2 processor can be run at several discrete 'PRCM configurations'. * These configurations are characterized by voltage and speed for clocks. * The device is only validated for certain combinations. One way to express - * these combinations is via the 'ratio's' which the clocks operate with + * these combinations is via the 'ratios' which the clocks operate with * respect to each other. These ratio sets are for a given voltage/DPLL - * setting. All configurations can be described by a DPLL setting and a ratio - * There are 3 ratio sets for the 2430 and X ratio sets for 2420. + * setting. All configurations can be described by a DPLL setting and a ratio. * * 2430 differs from 2420 in that there are no more phase synchronizers used. * They both have a slightly different clock domain setup. 2420(iva1,dsp) vs * 2430 (iva2.1, NOdsp, mdm) * * XXX Missing voltage data. + * XXX Missing 19.2MHz sys_clk rate sets. * * THe format described in this file is deprecated. Once a reasonable * OPP API exists, the data in this file should be converted to use it. @@ -30,24 +30,24 @@ #include "sdrc.h" #include "clock.h" -/*------------------------------------------------------------------------- - * Key dividers which make up a PRCM set. Ratio's for a PRCM are mandated. +/* + * Key dividers which make up a PRCM set. Ratios for a PRCM are mandated. * xtal_speed, dpll_speed, mpu_speed, CM_CLKSEL_MPU, * CM_CLKSEL_DSP, CM_CLKSEL_GFX, CM_CLKSEL1_CORE, CM_CLKSEL1_PLL, * CM_CLKSEL2_PLL, CM_CLKSEL_MDM * - * Filling in table based on H4 boards and 2430-SDPs variants available. - * There are quite a few more rates combinations which could be defined. + * Filling in table based on 2430-SDPs variants available. There are + * quite a few more rate combinations which could be defined. * - * When multiple values are defined the start up will try and choose the - * fastest one. If a 'fast' value is defined, then automatically, the /2 - * one should be included as it can be used. Generally having more that - * one fast set does not make sense, as static timings need to be changed - * to change the set. The exception is the bypass setting which is - * availble for low power bypass. + * When multiple values are defined the start up will try and choose + * the fastest one. If a 'fast' value is defined, then automatically, + * the /2 one should be included as it can be used. Generally having + * more than one fast set does not make sense, as static timings need + * to be changed to change the set. The exception is the bypass + * setting which is available for low power bypass. * * Note: This table needs to be sorted, fastest to slowest. - *-------------------------------------------------------------------------*/ + */ const struct prcm_config omap2430_rate_table[] = { /* PRCM #4 - ratio2 (ES2.1) - FAST */ {S13M, S798M, S399M, R2_CM_CLKSEL_MPU_VAL, /* 399MHz ARM */ diff --git a/arch/arm/mach-omap2/pm-debug.c b/arch/arm/mach-omap2/pm-debug.c index 860b755..a086626 100644 --- a/arch/arm/mach-omap2/pm-debug.c +++ b/arch/arm/mach-omap2/pm-debug.c @@ -54,8 +54,6 @@ int omap2_pm_debug; regs[reg_count++].val = \ __raw_readl(OMAP2_L4_IO_ADDRESS(0x480fe000 + (off))) -static int __init pm_dbg_init(void); - void omap2_pm_dump(int mode, int resume, unsigned int us) { struct reg { @@ -167,6 +165,8 @@ struct dentry *pm_dbg_dir; static int pm_dbg_init_done; +static int __init pm_dbg_init(void); + enum { DEBUG_FILE_COUNTERS = 0, DEBUG_FILE_TIMERS, @@ -488,9 +488,11 @@ int pm_dbg_regset_init(int reg_set) static int pwrdm_suspend_get(void *data, u64 *val) { - *val = omap3_pm_get_suspend_state((struct powerdomain *)data); + int ret; + ret = omap3_pm_get_suspend_state((struct powerdomain *)data); + *val = ret; - if (*val >= 0) + if (ret >= 0) return 0; return *val; } @@ -604,6 +606,4 @@ static int __init pm_dbg_init(void) } arch_initcall(pm_dbg_init); -#else -void pm_dbg_update_time(struct powerdomain *pwrdm, int prev) {} #endif diff --git a/arch/arm/mach-omap2/pm.h b/arch/arm/mach-omap2/pm.h index 0bf345d..7a9c2d0 100644 --- a/arch/arm/mach-omap2/pm.h +++ b/arch/arm/mach-omap2/pm.h @@ -32,12 +32,16 @@ extern struct omap_dm_timer *gptimer_wakeup; #ifdef CONFIG_PM_DEBUG extern void omap2_pm_dump(int mode, int resume, unsigned int us); extern int omap2_pm_debug; +#else +#define omap2_pm_dump(mode, resume, us) do {} while (0); +#define omap2_pm_debug 0 +#endif + +#if defined(CONFIG_PM_DEBUG) && defined(CONFIG_DEBUG_FS) extern void pm_dbg_update_time(struct powerdomain *pwrdm, int prev); extern int pm_dbg_regset_save(int reg_set); extern int pm_dbg_regset_init(int reg_set); #else -#define omap2_pm_dump(mode, resume, us) do {} while (0); -#define omap2_pm_debug 0 #define pm_dbg_update_time(pwrdm, prev) do {} while (0); #define pm_dbg_regset_save(reg_set) do {} while (0); #define pm_dbg_regset_init(reg_set) do {} while (0); diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c index 81ed252..910a7ac 100644 --- a/arch/arm/mach-omap2/pm34xx.c +++ b/arch/arm/mach-omap2/pm34xx.c @@ -26,6 +26,7 @@ #include <linux/err.h> #include <linux/gpio.h> #include <linux/clk.h> +#include <linux/delay.h> #include <plat/sram.h> #include <plat/clockdomain.h> @@ -124,9 +125,17 @@ static void omap3_core_save_context(void) control_padconf_off |= START_PADCONF_SAVE; omap_ctrl_writel(control_padconf_off, OMAP343X_CONTROL_PADCONF_OFF); /* wait for the save to complete */ - while (!omap_ctrl_readl(OMAP343X_CONTROL_GENERAL_PURPOSE_STATUS) - & PADCONF_SAVE_DONE) - ; + while (!(omap_ctrl_readl(OMAP343X_CONTROL_GENERAL_PURPOSE_STATUS) + & PADCONF_SAVE_DONE)) + udelay(1); + + /* + * Force write last pad into memory, as this can fail in some + * cases according to erratas 1.157, 1.185 + */ + omap_ctrl_writel(omap_ctrl_readl(OMAP343X_PADCONF_ETK_D14), + OMAP343X_CONTROL_MEM_WKUP + 0x2a0); + /* Save the Interrupt controller context */ omap_intc_save_context(); /* Save the GPMC context */ @@ -392,6 +401,7 @@ void omap_sram_idle(void) prm_set_mod_reg_bits(OMAP3430_EN_IO, WKUP_MOD, PM_WKEN); omap3_enable_io_chain(); } + omap3_intc_prepare_idle(); /* * On EMU/HS devices ROM code restores a SRDC value @@ -438,6 +448,7 @@ void omap_sram_idle(void) OMAP3430_GR_MOD, OMAP3_PRM_VOLTCTRL_OFFSET); } + omap3_intc_resume_idle(); /* PER */ if (per_next_state < PWRDM_POWER_ON) { @@ -578,6 +589,8 @@ static int omap3_pm_suspend(void) } omap_uart_prepare_suspend(); + omap3_intc_suspend(); + omap_sram_idle(); restore: @@ -835,6 +848,8 @@ static void __init prcm_setup_regs(void) CM_AUTOIDLE); } + omap_ctrl_writel(OMAP3430_AUTOIDLE, OMAP2_CONTROL_SYSCONFIG); + /* * Set all plls to autoidle. This is needed until autoidle is * enabled by clockfw @@ -875,15 +890,23 @@ static void __init prcm_setup_regs(void) prm_write_mod_reg(OMAP3430_IO_EN | OMAP3430_WKUP_EN, OCP_MOD, OMAP3_PRM_IRQENABLE_MPU_OFFSET); + /* Enable PM_WKEN to support DSS LPR */ + prm_write_mod_reg(OMAP3430_PM_WKEN_DSS_EN_DSS, + OMAP3430_DSS_MOD, PM_WKEN); + /* Enable wakeups in PER */ prm_write_mod_reg(OMAP3430_EN_GPIO2 | OMAP3430_EN_GPIO3 | OMAP3430_EN_GPIO4 | OMAP3430_EN_GPIO5 | - OMAP3430_EN_GPIO6 | OMAP3430_EN_UART3, + OMAP3430_EN_GPIO6 | OMAP3430_EN_UART3 | + OMAP3430_EN_MCBSP2 | OMAP3430_EN_MCBSP3 | + OMAP3430_EN_MCBSP4, OMAP3430_PER_MOD, PM_WKEN); /* and allow them to wake up MPU */ prm_write_mod_reg(OMAP3430_GRPSEL_GPIO2 | OMAP3430_EN_GPIO3 | OMAP3430_GRPSEL_GPIO4 | OMAP3430_EN_GPIO5 | - OMAP3430_GRPSEL_GPIO6 | OMAP3430_EN_UART3, + OMAP3430_GRPSEL_GPIO6 | OMAP3430_EN_UART3 | + OMAP3430_EN_MCBSP2 | OMAP3430_EN_MCBSP3 | + OMAP3430_EN_MCBSP4, OMAP3430_PER_MOD, OMAP3430_PM_MPUGRPSEL); /* Don't attach IVA interrupts */ @@ -904,24 +927,6 @@ static void __init prcm_setup_regs(void) /* Clear any pending PRCM interrupts */ prm_write_mod_reg(0, OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET); - /* Don't attach IVA interrupts */ - prm_write_mod_reg(0, WKUP_MOD, OMAP3430_PM_IVAGRPSEL); - prm_write_mod_reg(0, CORE_MOD, OMAP3430_PM_IVAGRPSEL1); - prm_write_mod_reg(0, CORE_MOD, OMAP3430ES2_PM_IVAGRPSEL3); - prm_write_mod_reg(0, OMAP3430_PER_MOD, OMAP3430_PM_IVAGRPSEL); - - /* Clear any pending 'reset' flags */ - prm_write_mod_reg(0xffffffff, MPU_MOD, RM_RSTST); - prm_write_mod_reg(0xffffffff, CORE_MOD, RM_RSTST); - prm_write_mod_reg(0xffffffff, OMAP3430_PER_MOD, RM_RSTST); - prm_write_mod_reg(0xffffffff, OMAP3430_EMU_MOD, RM_RSTST); - prm_write_mod_reg(0xffffffff, OMAP3430_NEON_MOD, RM_RSTST); - prm_write_mod_reg(0xffffffff, OMAP3430_DSS_MOD, RM_RSTST); - prm_write_mod_reg(0xffffffff, OMAP3430ES2_USBHOST_MOD, RM_RSTST); - - /* Clear any pending PRCM interrupts */ - prm_write_mod_reg(0, OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET); - omap3_iva_idle(); omap3_d2d_idle(); } diff --git a/arch/arm/mach-omap2/prcm.c b/arch/arm/mach-omap2/prcm.c index 3ea8177..cf466ea 100644 --- a/arch/arm/mach-omap2/prcm.c +++ b/arch/arm/mach-omap2/prcm.c @@ -44,7 +44,6 @@ struct omap3_prcm_regs { u32 iva2_cm_clksel2; u32 cm_sysconfig; u32 sgx_cm_clksel; - u32 wkup_cm_clksel; u32 dss_cm_clksel; u32 cam_cm_clksel; u32 per_cm_clksel; @@ -53,7 +52,6 @@ struct omap3_prcm_regs { u32 pll_cm_autoidle2; u32 pll_cm_clksel4; u32 pll_cm_clksel5; - u32 pll_cm_clken; u32 pll_cm_clken2; u32 cm_polctrl; u32 iva2_cm_fclken; @@ -77,7 +75,6 @@ struct omap3_prcm_regs { u32 usbhost_cm_iclken; u32 iva2_cm_autiidle2; u32 mpu_cm_autoidle2; - u32 pll_cm_autoidle; u32 iva2_cm_clkstctrl; u32 mpu_cm_clkstctrl; u32 core_cm_clkstctrl; @@ -274,7 +271,6 @@ void omap3_prcm_save_context(void) prcm_context.cm_sysconfig = __raw_readl(OMAP3430_CM_SYSCONFIG); prcm_context.sgx_cm_clksel = cm_read_mod_reg(OMAP3430ES2_SGX_MOD, CM_CLKSEL); - prcm_context.wkup_cm_clksel = cm_read_mod_reg(WKUP_MOD, CM_CLKSEL); prcm_context.dss_cm_clksel = cm_read_mod_reg(OMAP3430_DSS_MOD, CM_CLKSEL); prcm_context.cam_cm_clksel = @@ -291,8 +287,6 @@ void omap3_prcm_save_context(void) cm_read_mod_reg(PLL_MOD, OMAP3430ES2_CM_CLKSEL4); prcm_context.pll_cm_clksel5 = cm_read_mod_reg(PLL_MOD, OMAP3430ES2_CM_CLKSEL5); - prcm_context.pll_cm_clken = - cm_read_mod_reg(PLL_MOD, CM_CLKEN); prcm_context.pll_cm_clken2 = cm_read_mod_reg(PLL_MOD, OMAP3430ES2_CM_CLKEN2); prcm_context.cm_polctrl = __raw_readl(OMAP3430_CM_POLCTRL); @@ -338,8 +332,6 @@ void omap3_prcm_save_context(void) cm_read_mod_reg(OMAP3430_IVA2_MOD, CM_AUTOIDLE2); prcm_context.mpu_cm_autoidle2 = cm_read_mod_reg(MPU_MOD, CM_AUTOIDLE2); - prcm_context.pll_cm_autoidle = - cm_read_mod_reg(PLL_MOD, CM_AUTOIDLE); prcm_context.iva2_cm_clkstctrl = cm_read_mod_reg(OMAP3430_IVA2_MOD, CM_CLKSTCTRL); prcm_context.mpu_cm_clkstctrl = @@ -431,7 +423,6 @@ void omap3_prcm_restore_context(void) __raw_writel(prcm_context.cm_sysconfig, OMAP3430_CM_SYSCONFIG); cm_write_mod_reg(prcm_context.sgx_cm_clksel, OMAP3430ES2_SGX_MOD, CM_CLKSEL); - cm_write_mod_reg(prcm_context.wkup_cm_clksel, WKUP_MOD, CM_CLKSEL); cm_write_mod_reg(prcm_context.dss_cm_clksel, OMAP3430_DSS_MOD, CM_CLKSEL); cm_write_mod_reg(prcm_context.cam_cm_clksel, OMAP3430_CAM_MOD, @@ -448,7 +439,6 @@ void omap3_prcm_restore_context(void) OMAP3430ES2_CM_CLKSEL4); cm_write_mod_reg(prcm_context.pll_cm_clksel5, PLL_MOD, OMAP3430ES2_CM_CLKSEL5); - cm_write_mod_reg(prcm_context.pll_cm_clken, PLL_MOD, CM_CLKEN); cm_write_mod_reg(prcm_context.pll_cm_clken2, PLL_MOD, OMAP3430ES2_CM_CLKEN2); __raw_writel(prcm_context.cm_polctrl, OMAP3430_CM_POLCTRL); @@ -487,7 +477,6 @@ void omap3_prcm_restore_context(void) cm_write_mod_reg(prcm_context.iva2_cm_autiidle2, OMAP3430_IVA2_MOD, CM_AUTOIDLE2); cm_write_mod_reg(prcm_context.mpu_cm_autoidle2, MPU_MOD, CM_AUTOIDLE2); - cm_write_mod_reg(prcm_context.pll_cm_autoidle, PLL_MOD, CM_AUTOIDLE); cm_write_mod_reg(prcm_context.iva2_cm_clkstctrl, OMAP3430_IVA2_MOD, CM_CLKSTCTRL); cm_write_mod_reg(prcm_context.mpu_cm_clkstctrl, MPU_MOD, CM_CLKSTCTRL); diff --git a/arch/arm/mach-omap2/prm.h b/arch/arm/mach-omap2/prm.h index ea050ce..40f0062 100644 --- a/arch/arm/mach-omap2/prm.h +++ b/arch/arm/mach-omap2/prm.h @@ -24,6 +24,8 @@ OMAP2_L4_IO_ADDRESS(OMAP3430_PRM_BASE + (module) + (reg)) #define OMAP44XX_PRM_REGADDR(module, reg) \ OMAP2_L4_IO_ADDRESS(OMAP4430_PRM_BASE + (module) + (reg)) +#define OMAP44XX_CHIRONSS_REGADDR(module, reg) \ + OMAP2_L4_IO_ADDRESS(OMAP4430_CHIRONSS_BASE + (module) + (reg)) #include "prm44xx.h" diff --git a/arch/arm/mach-omap2/prm44xx.h b/arch/arm/mach-omap2/prm44xx.h index 89be97f..adb2558 100644 --- a/arch/arm/mach-omap2/prm44xx.h +++ b/arch/arm/mach-omap2/prm44xx.h @@ -386,26 +386,26 @@ /* CHIRON_PRCM.CHIRONSS_OCP_SOCKET_PRCM register offsets */ -#define OMAP4430_REVISION_PRCM OMAP44XX_PRM_REGADDR(OMAP4430_CHIRONSS_CHIRONSS_OCP_SOCKET_PRCM_MOD, 0x0000) +#define OMAP4430_REVISION_PRCM OMAP44XX_CHIRONSS_REGADDR(OMAP4430_CHIRONSS_CHIRONSS_OCP_SOCKET_PRCM_MOD, 0x0000) /* CHIRON_PRCM.CHIRONSS_DEVICE_PRM register offsets */ -#define OMAP4430_CHIRON_PRCM_PRM_RSTST OMAP44XX_PRM_REGADDR(OMAP4430_CHIRONSS_CHIRONSS_DEVICE_PRM_MOD, 0x0000) +#define OMAP4430_CHIRON_PRCM_PRM_RSTST OMAP44XX_CHIRONSS_REGADDR(OMAP4430_CHIRONSS_CHIRONSS_DEVICE_PRM_MOD, 0x0000) /* CHIRON_PRCM.CHIRONSS_CPU0 register offsets */ -#define OMAP4430_PM_PDA_CPU0_PWRSTCTRL OMAP44XX_PRM_REGADDR(OMAP4430_CHIRONSS_CHIRONSS_CPU0_MOD, 0x0000) -#define OMAP4430_PM_PDA_CPU0_PWRSTST OMAP44XX_PRM_REGADDR(OMAP4430_CHIRONSS_CHIRONSS_CPU0_MOD, 0x0004) -#define OMAP4430_RM_PDA_CPU0_CPU0_CONTEXT OMAP44XX_PRM_REGADDR(OMAP4430_CHIRONSS_CHIRONSS_CPU0_MOD, 0x0008) -#define OMAP4430_RM_PDA_CPU0_CPU0_RSTCTRL OMAP44XX_PRM_REGADDR(OMAP4430_CHIRONSS_CHIRONSS_CPU0_MOD, 0x000c) -#define OMAP4430_RM_PDA_CPU0_CPU0_RSTST OMAP44XX_PRM_REGADDR(OMAP4430_CHIRONSS_CHIRONSS_CPU0_MOD, 0x0010) -#define OMAP4430_CM_PDA_CPU0_CPU0_CLKCTRL OMAP44XX_PRM_REGADDR(OMAP4430_CHIRONSS_CHIRONSS_CPU0_MOD, 0x0014) -#define OMAP4430_CM_PDA_CPU0_CLKSTCTRL OMAP44XX_PRM_REGADDR(OMAP4430_CHIRONSS_CHIRONSS_CPU0_MOD, 0x0018) +#define OMAP4430_PM_PDA_CPU0_PWRSTCTRL OMAP44XX_CHIRONSS_REGADDR(OMAP4430_CHIRONSS_CHIRONSS_CPU0_MOD, 0x0000) +#define OMAP4430_PM_PDA_CPU0_PWRSTST OMAP44XX_CHIRONSS_REGADDR(OMAP4430_CHIRONSS_CHIRONSS_CPU0_MOD, 0x0004) +#define OMAP4430_RM_PDA_CPU0_CPU0_CONTEXT OMAP44XX_CHIRONSS_REGADDR(OMAP4430_CHIRONSS_CHIRONSS_CPU0_MOD, 0x0008) +#define OMAP4430_RM_PDA_CPU0_CPU0_RSTCTRL OMAP44XX_CHIRONSS_REGADDR(OMAP4430_CHIRONSS_CHIRONSS_CPU0_MOD, 0x000c) +#define OMAP4430_RM_PDA_CPU0_CPU0_RSTST OMAP44XX_CHIRONSS_REGADDR(OMAP4430_CHIRONSS_CHIRONSS_CPU0_MOD, 0x0010) +#define OMAP4430_CM_PDA_CPU0_CPU0_CLKCTRL OMAP44XX_CHIRONSS_REGADDR(OMAP4430_CHIRONSS_CHIRONSS_CPU0_MOD, 0x0014) +#define OMAP4430_CM_PDA_CPU0_CLKSTCTRL OMAP44XX_CHIRONSS_REGADDR(OMAP4430_CHIRONSS_CHIRONSS_CPU0_MOD, 0x0018) /* CHIRON_PRCM.CHIRONSS_CPU1 register offsets */ -#define OMAP4430_PM_PDA_CPU1_PWRSTCTRL OMAP44XX_PRM_REGADDR(OMAP4430_CHIRONSS_CHIRONSS_CPU1_MOD, 0x0000) -#define OMAP4430_PM_PDA_CPU1_PWRSTST OMAP44XX_PRM_REGADDR(OMAP4430_CHIRONSS_CHIRONSS_CPU1_MOD, 0x0004) -#define OMAP4430_RM_PDA_CPU1_CPU1_CONTEXT OMAP44XX_PRM_REGADDR(OMAP4430_CHIRONSS_CHIRONSS_CPU1_MOD, 0x0008) -#define OMAP4430_RM_PDA_CPU1_CPU1_RSTCTRL OMAP44XX_PRM_REGADDR(OMAP4430_CHIRONSS_CHIRONSS_CPU1_MOD, 0x000c) -#define OMAP4430_RM_PDA_CPU1_CPU1_RSTST OMAP44XX_PRM_REGADDR(OMAP4430_CHIRONSS_CHIRONSS_CPU1_MOD, 0x0010) -#define OMAP4430_CM_PDA_CPU1_CPU1_CLKCTRL OMAP44XX_PRM_REGADDR(OMAP4430_CHIRONSS_CHIRONSS_CPU1_MOD, 0x0014) -#define OMAP4430_CM_PDA_CPU1_CLKSTCTRL OMAP44XX_PRM_REGADDR(OMAP4430_CHIRONSS_CHIRONSS_CPU1_MOD, 0x0018) +#define OMAP4430_PM_PDA_CPU1_PWRSTCTRL OMAP44XX_CHIRONSS_REGADDR(OMAP4430_CHIRONSS_CHIRONSS_CPU1_MOD, 0x0000) +#define OMAP4430_PM_PDA_CPU1_PWRSTST OMAP44XX_CHIRONSS_REGADDR(OMAP4430_CHIRONSS_CHIRONSS_CPU1_MOD, 0x0004) +#define OMAP4430_RM_PDA_CPU1_CPU1_CONTEXT OMAP44XX_CHIRONSS_REGADDR(OMAP4430_CHIRONSS_CHIRONSS_CPU1_MOD, 0x0008) +#define OMAP4430_RM_PDA_CPU1_CPU1_RSTCTRL OMAP44XX_CHIRONSS_REGADDR(OMAP4430_CHIRONSS_CHIRONSS_CPU1_MOD, 0x000c) +#define OMAP4430_RM_PDA_CPU1_CPU1_RSTST OMAP44XX_CHIRONSS_REGADDR(OMAP4430_CHIRONSS_CHIRONSS_CPU1_MOD, 0x0010) +#define OMAP4430_CM_PDA_CPU1_CPU1_CLKCTRL OMAP44XX_CHIRONSS_REGADDR(OMAP4430_CHIRONSS_CHIRONSS_CPU1_MOD, 0x0014) +#define OMAP4430_CM_PDA_CPU1_CLKSTCTRL OMAP44XX_CHIRONSS_REGADDR(OMAP4430_CHIRONSS_CHIRONSS_CPU1_MOD, 0x0018) #endif diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c index 19805a7..e10a02d 100644 --- a/arch/arm/mach-omap2/serial.c +++ b/arch/arm/mach-omap2/serial.c @@ -36,7 +36,13 @@ #define UART_OMAP_NO_EMPTY_FIFO_READ_IP_REV 0x52 #define UART_OMAP_WER 0x17 /* Wake-up enable register */ -#define DEFAULT_TIMEOUT (5 * HZ) +/* + * NOTE: By default the serial timeout is disabled as it causes lost characters + * over the serial ports. This means that the UART clocks will stay on until + * disabled via sysfs. This also causes that any deeper omap sleep states are + * blocked. + */ +#define DEFAULT_TIMEOUT 0 struct omap_uart_state { int num; @@ -125,6 +131,13 @@ static struct plat_serial8250_port serial_platform_data3[] = { } }; #endif +static inline unsigned int __serial_read_reg(struct uart_port *up, + int offset) +{ + offset <<= up->regshift; + return (unsigned int)__raw_readb(up->membase + offset); +} + static inline unsigned int serial_read_reg(struct plat_serial8250_port *up, int offset) { @@ -415,7 +428,8 @@ static void omap_uart_idle_init(struct omap_uart_state *uart) uart->timeout = DEFAULT_TIMEOUT; setup_timer(&uart->timer, omap_uart_idle_timer, (unsigned long) uart); - mod_timer(&uart->timer, jiffies + uart->timeout); + if (uart->timeout) + mod_timer(&uart->timer, jiffies + uart->timeout); omap_uart_smart_idle_enable(uart, 0); if (cpu_is_omap34xx()) { @@ -583,11 +597,12 @@ static unsigned int serial_in_override(struct uart_port *up, int offset) { if (UART_RX == offset) { unsigned int lsr; - lsr = serial_read_reg(omap_uart[up->line].p, UART_LSR); + lsr = __serial_read_reg(up, UART_LSR); if (!(lsr & UART_LSR_DR)) return -EPERM; } - return serial_read_reg(omap_uart[up->line].p, offset); + + return __serial_read_reg(up, offset); } void __init omap_serial_early_init(void) diff --git a/arch/arm/mach-omap2/sleep34xx.S b/arch/arm/mach-omap2/sleep34xx.S index 15268f8..c3626ea 100644 --- a/arch/arm/mach-omap2/sleep34xx.S +++ b/arch/arm/mach-omap2/sleep34xx.S @@ -245,7 +245,8 @@ restore: mov r1, #0 @ set task id for ROM code in r1 mov r2, #4 @ set some flags in r2, r6 mov r6, #0xff - adr r3, write_aux_control_params @ r3 points to parameters + ldr r4, scratchpad_base + ldr r3, [r4, #0xBC] @ r3 points to parameters mcr p15, 0, r0, c7, c10, 4 @ data write barrier mcr p15, 0, r0, c7, c10, 5 @ data memory barrier .word 0xE1600071 @ call SMI monitor (smi #1) @@ -253,14 +254,14 @@ restore: b logic_l1_restore l2_inv_api_params: .word 0x1, 0x00 -write_aux_control_params: - .word 0x1, 0x72 l2_inv_gp: /* Execute smi to invalidate L2 cache */ mov r12, #0x1 @ set up to invalide L2 smi: .word 0xE1600070 @ Call SMI monitor (smieq) /* Write to Aux control register to set some bits */ - mov r0, #0x72 + ldr r4, scratchpad_base + ldr r3, [r4,#0xBC] + ldr r0, [r3,#4] mov r12, #0x3 .word 0xE1600070 @ Call SMI monitor (smieq) logic_l1_restore: @@ -271,6 +272,7 @@ logic_l1_restore: ldr r4, scratchpad_base ldr r3, [r4,#0xBC] + adds r3, r3, #8 ldmia r3!, {r4-r6} mov sp, r4 msr spsr_cxsf, r5 @@ -387,6 +389,9 @@ usettbr0: save_context_wfi: /*b save_context_wfi*/ @ enable to debug save code mov r8, r0 /* Store SDRAM address in r8 */ + mrc p15, 0, r5, c1, c0, 1 @ Read Auxiliary Control Register + mov r4, #0x1 @ Number of parameters for restore call + stmia r8!, {r4-r5} /* Check what that target sleep state is:stored in r1*/ /* 1 - Only L1 and logic lost */ /* 2 - Only L2 lost */ diff --git a/arch/arm/mach-orion5x/dns323-setup.c b/arch/arm/mach-orion5x/dns323-setup.c index b31ca4c..8f159db 100644 --- a/arch/arm/mach-orion5x/dns323-setup.c +++ b/arch/arm/mach-orion5x/dns323-setup.c @@ -12,6 +12,7 @@ #include <linux/kernel.h> #include <linux/init.h> +#include <linux/delay.h> #include <linux/platform_device.h> #include <linux/pci.h> #include <linux/irq.h> @@ -32,6 +33,7 @@ #define DNS323_GPIO_LED_RIGHT_AMBER 1 #define DNS323_GPIO_LED_LEFT_AMBER 2 +#define DNS323_GPIO_SYSTEM_UP 3 #define DNS323_GPIO_LED_POWER 5 #define DNS323_GPIO_OVERTEMP 6 #define DNS323_GPIO_RTC 7 @@ -239,7 +241,7 @@ static struct gpio_led dns323_leds[] = { { .name = "power:blue", .gpio = DNS323_GPIO_LED_POWER, - .active_low = 1, + .default_state = LEDS_GPIO_DEFSTATE_ON, }, { .name = "right:amber", .gpio = DNS323_GPIO_LED_RIGHT_AMBER, @@ -334,7 +336,7 @@ static struct orion5x_mpp_mode dns323_mv88f5182_mpp_modes[] __initdata = { { 0, MPP_UNUSED }, { 1, MPP_GPIO }, /* right amber LED (sata ch0) */ { 2, MPP_GPIO }, /* left amber LED (sata ch1) */ - { 3, MPP_UNUSED }, + { 3, MPP_GPIO }, /* system up flag */ { 4, MPP_GPIO }, /* power button LED */ { 5, MPP_GPIO }, /* power button LED */ { 6, MPP_GPIO }, /* GMT G751-2f overtemp */ @@ -372,13 +374,23 @@ static struct i2c_board_info __initdata dns323_i2c_devices[] = { }, }; -/* DNS-323 specific power off method */ -static void dns323_power_off(void) +/* DNS-323 rev. A specific power off method */ +static void dns323a_power_off(void) { pr_info("%s: triggering power-off...\n", __func__); gpio_set_value(DNS323_GPIO_POWER_OFF, 1); } +/* DNS-323 rev B specific power off method */ +static void dns323b_power_off(void) +{ + pr_info("%s: triggering power-off...\n", __func__); + /* Pin has to be changed to 1 and back to 0 to do actual power off. */ + gpio_set_value(DNS323_GPIO_POWER_OFF, 1); + mdelay(100); + gpio_set_value(DNS323_GPIO_POWER_OFF, 0); +} + static void __init dns323_init(void) { /* Setup basic Orion functions. Need to be called early. */ @@ -424,11 +436,20 @@ static void __init dns323_init(void) if (dns323_dev_id() == MV88F5182_DEV_ID) orion5x_sata_init(&dns323_sata_data); - /* register dns323 specific power-off method */ + /* The 5182 has flag to indicate the system is up. Without this flag + * set, power LED will flash and cannot be controlled via leds-gpio. + */ + if (dns323_dev_id() == MV88F5182_DEV_ID) + gpio_set_value(DNS323_GPIO_SYSTEM_UP, 1); + + /* Register dns323 specific power-off method */ if (gpio_request(DNS323_GPIO_POWER_OFF, "POWEROFF") != 0 || gpio_direction_output(DNS323_GPIO_POWER_OFF, 0) != 0) pr_err("DNS323: failed to setup power-off GPIO\n"); - pm_power_off = dns323_power_off; + if (dns323_dev_id() == MV88F5182_DEV_ID) + pm_power_off = dns323b_power_off; + else + pm_power_off = dns323a_power_off; } /* Warning: D-Link uses a wrong mach-type (=526) in their bootloader */ diff --git a/arch/arm/mach-orion5x/wrt350n-v2-setup.c b/arch/arm/mach-orion5x/wrt350n-v2-setup.c index 1b4ad9d..cb0feca 100644 --- a/arch/arm/mach-orion5x/wrt350n-v2-setup.c +++ b/arch/arm/mach-orion5x/wrt350n-v2-setup.c @@ -15,6 +15,9 @@ #include <linux/mtd/physmap.h> #include <linux/mv643xx_eth.h> #include <linux/ethtool.h> +#include <linux/leds.h> +#include <linux/gpio_keys.h> +#include <linux/input.h> #include <net/dsa.h> #include <asm/mach-types.h> #include <asm/gpio.h> @@ -24,6 +27,80 @@ #include "common.h" #include "mpp.h" +/* + * LEDs attached to GPIO + */ +static struct gpio_led wrt350n_v2_led_pins[] = { + { + .name = "wrt350nv2:green:power", + .gpio = 0, + .active_low = 1, + }, { + .name = "wrt350nv2:green:security", + .gpio = 1, + .active_low = 1, + }, { + .name = "wrt350nv2:orange:power", + .gpio = 5, + .active_low = 1, + }, { + .name = "wrt350nv2:green:usb", + .gpio = 6, + .active_low = 1, + }, { + .name = "wrt350nv2:green:wireless", + .gpio = 7, + .active_low = 1, + }, +}; + +static struct gpio_led_platform_data wrt350n_v2_led_data = { + .leds = wrt350n_v2_led_pins, + .num_leds = ARRAY_SIZE(wrt350n_v2_led_pins), +}; + +static struct platform_device wrt350n_v2_leds = { + .name = "leds-gpio", + .id = -1, + .dev = { + .platform_data = &wrt350n_v2_led_data, + }, +}; + +/* + * Buttons attached to GPIO + */ +static struct gpio_keys_button wrt350n_v2_buttons[] = { + { + .code = KEY_RESTART, + .gpio = 3, + .desc = "Reset Button", + .active_low = 1, + }, { + .code = KEY_WLAN, + .gpio = 2, + .desc = "WPS Button", + .active_low = 1, + }, +}; + +static struct gpio_keys_platform_data wrt350n_v2_button_data = { + .buttons = wrt350n_v2_buttons, + .nbuttons = ARRAY_SIZE(wrt350n_v2_buttons), +}; + +static struct platform_device wrt350n_v2_button_device = { + .name = "gpio-keys", + .id = -1, + .num_resources = 0, + .dev = { + .platform_data = &wrt350n_v2_button_data, + }, +}; + +/* + * General setup + */ static struct orion5x_mpp_mode wrt350n_v2_mpp_modes[] __initdata = { { 0, MPP_GPIO }, /* Power LED green (0=on) */ { 1, MPP_GPIO }, /* Security LED (0=on) */ @@ -140,6 +217,8 @@ static void __init wrt350n_v2_init(void) orion5x_setup_dev_boot_win(WRT350N_V2_NOR_BOOT_BASE, WRT350N_V2_NOR_BOOT_SIZE); platform_device_register(&wrt350n_v2_nor_flash); + platform_device_register(&wrt350n_v2_leds); + platform_device_register(&wrt350n_v2_button_device); } static int __init wrt350n_v2_pci_map_irq(struct pci_dev *dev, u8 slot, u8 pin) diff --git a/arch/arm/mach-pxa/corgi.c b/arch/arm/mach-pxa/corgi.c index 74446cf..da3156d86 100644 --- a/arch/arm/mach-pxa/corgi.c +++ b/arch/arm/mach-pxa/corgi.c @@ -457,6 +457,7 @@ static struct pxaficp_platform_data corgi_ficp_platform_data = { * USB Device Controller */ static struct pxa2xx_udc_mach_info udc_info __initdata = { + .gpio_vbus = -1, /* no connect GPIO; corgi can't tell connection status */ .gpio_pullup = CORGI_GPIO_USB_PULLUP, }; diff --git a/arch/arm/mach-pxa/include/mach/hardware.h b/arch/arm/mach-pxa/include/mach/hardware.h index 50f1297..e741bf1 100644 --- a/arch/arm/mach-pxa/include/mach/hardware.h +++ b/arch/arm/mach-pxa/include/mach/hardware.h @@ -250,20 +250,17 @@ #define cpu_is_pxa930() \ ({ \ - unsigned int id = read_cpuid(CPUID_ID); \ - __cpu_is_pxa930(id); \ + __cpu_is_pxa930(read_cpuid_id()); \ }) #define cpu_is_pxa935() \ ({ \ - unsigned int id = read_cpuid(CPUID_ID); \ - __cpu_is_pxa935(id); \ + __cpu_is_pxa935(read_cpuid_id()); \ }) #define cpu_is_pxa950() \ ({ \ - unsigned int id = read_cpuid(CPUID_ID); \ - __cpu_is_pxa950(id); \ + __cpu_is_pxa950(read_cpuid_id()); \ }) diff --git a/arch/arm/mach-pxa/include/mach/mfp-pxa25x.h b/arch/arm/mach-pxa/include/mach/mfp-pxa25x.h index b13dc02..9c78785 100644 --- a/arch/arm/mach-pxa/include/mach/mfp-pxa25x.h +++ b/arch/arm/mach-pxa/include/mach/mfp-pxa25x.h @@ -169,7 +169,6 @@ #define GPIO86_nSDCS2 MFP_CFG_OUT(GPIO86, AF0, DRIVE_HIGH) #define GPIO87_nSDCS3 MFP_CFG_OUT(GPIO87, AF0, DRIVE_HIGH) #define GPIO88_RDnWR MFP_CFG_OUT(GPIO88, AF0, DRIVE_HIGH) -#define GPIO89_nACRESET MFP_CFG_OUT(GPIO89, AF0, DRIVE_HIGH) /* USB */ #define GPIO9_USB_RCV MFP_CFG_IN(GPIO9, AF1) @@ -186,6 +185,9 @@ #define GPIO30_ASSP_TXD MFP_CFG_OUT(GPIO30, AF3, DRIVE_LOW) #define GPIO31_ASSP_SFRM_IN MFP_CFG_IN(GPIO31, AF1) #define GPIO31_ASSP_SFRM_OUT MFP_CFG_OUT(GPIO31, AF3, DRIVE_LOW) -#endif + +/* AC97 */ +#define GPIO89_AC97_nRESET MFP_CFG_OUT(GPIO89, AF0, DRIVE_HIGH) +#endif /* CONFIG_CPU_PXA26x */ #endif /* __ASM_ARCH_MFP_PXA25X_H */ diff --git a/arch/arm/mach-pxa/irq.c b/arch/arm/mach-pxa/irq.c index 6112af4..1beb40f 100644 --- a/arch/arm/mach-pxa/irq.c +++ b/arch/arm/mach-pxa/irq.c @@ -164,8 +164,11 @@ static int pxa_irq_suspend(struct sys_device *dev, pm_message_t state) saved_icmr[i] = _ICMR(irq); _ICMR(irq) = 0; } - for (i = 0; i < pxa_internal_irq_nr; i++) - saved_ipr[i] = IPR(i); + + if (cpu_is_pxa27x() || cpu_is_pxa3xx()) { + for (i = 0; i < pxa_internal_irq_nr; i++) + saved_ipr[i] = IPR(i); + } return 0; } @@ -174,12 +177,15 @@ static int pxa_irq_resume(struct sys_device *dev) { int i, irq = PXA_IRQ(0); + if (cpu_is_pxa27x() || cpu_is_pxa3xx()) { + for (i = 0; i < pxa_internal_irq_nr; i++) + IPR(i) = saved_ipr[i]; + } + for (i = 0; irq < PXA_IRQ(pxa_internal_irq_nr); i++, irq += 32) { _ICMR(irq) = saved_icmr[i]; _ICLR(irq) = 0; } - for (i = 0; i < pxa_internal_irq_nr; i++) - IPR(i) = saved_ipr[i]; ICCR = 1; return 0; diff --git a/arch/arm/mach-pxa/magician.c b/arch/arm/mach-pxa/magician.c index 8a38d60..189f330 100644 --- a/arch/arm/mach-pxa/magician.c +++ b/arch/arm/mach-pxa/magician.c @@ -381,7 +381,7 @@ err: return ret; } -static int magician_backlight_notify(int brightness) +static int magician_backlight_notify(struct device *dev, int brightness) { gpio_set_value(EGPIO_MAGICIAN_BL_POWER, brightness); if (brightness >= 200) { diff --git a/arch/arm/mach-pxa/palmld.c b/arch/arm/mach-pxa/palmld.c index 5914021..e100af7 100644 --- a/arch/arm/mach-pxa/palmld.c +++ b/arch/arm/mach-pxa/palmld.c @@ -270,7 +270,7 @@ err: return ret; } -static int palmld_backlight_notify(int brightness) +static int palmld_backlight_notify(struct device *dev, int brightness) { gpio_set_value(GPIO_NR_PALMLD_BL_POWER, brightness); gpio_set_value(GPIO_NR_PALMLD_LCD_POWER, brightness); diff --git a/arch/arm/mach-pxa/palmt5.c b/arch/arm/mach-pxa/palmt5.c index 7f89ca2..8fe3ec2 100644 --- a/arch/arm/mach-pxa/palmt5.c +++ b/arch/arm/mach-pxa/palmt5.c @@ -209,7 +209,7 @@ err: return ret; } -static int palmt5_backlight_notify(int brightness) +static int palmt5_backlight_notify(struct device *dev, int brightness) { gpio_set_value(GPIO_NR_PALMT5_BL_POWER, brightness); gpio_set_value(GPIO_NR_PALMT5_LCD_POWER, brightness); diff --git a/arch/arm/mach-pxa/palmtc.c b/arch/arm/mach-pxa/palmtc.c index 3084175..b992f07 100644 --- a/arch/arm/mach-pxa/palmtc.c +++ b/arch/arm/mach-pxa/palmtc.c @@ -185,7 +185,7 @@ err: return ret; } -static int palmtc_backlight_notify(int brightness) +static int palmtc_backlight_notify(struct device *dev, int brightness) { /* backlight is on when GPIO16 AF0 is high */ gpio_set_value(GPIO_NR_PALMTC_BL_POWER, brightness); diff --git a/arch/arm/mach-pxa/palmte2.c b/arch/arm/mach-pxa/palmte2.c index 265d62b..dc728d6 100644 --- a/arch/arm/mach-pxa/palmte2.c +++ b/arch/arm/mach-pxa/palmte2.c @@ -181,7 +181,7 @@ err: return ret; } -static int palmte2_backlight_notify(int brightness) +static int palmte2_backlight_notify(struct device *dev, int brightness) { gpio_set_value(GPIO_NR_PALMTE2_BL_POWER, brightness); gpio_set_value(GPIO_NR_PALMTE2_LCD_POWER, brightness); diff --git a/arch/arm/mach-pxa/palmtreo.c b/arch/arm/mach-pxa/palmtreo.c index 606eb7e..b433bb4 100644 --- a/arch/arm/mach-pxa/palmtreo.c +++ b/arch/arm/mach-pxa/palmtreo.c @@ -375,7 +375,7 @@ err: return ret; } -static int treo_backlight_notify(int brightness) +static int treo_backlight_notify(struct device *dev, int brightness) { gpio_set_value(GPIO_NR_TREO_BL_POWER, brightness); return TREO_MAX_INTENSITY - brightness; diff --git a/arch/arm/mach-pxa/palmtx.c b/arch/arm/mach-pxa/palmtx.c index 7bf18c2..b37a025 100644 --- a/arch/arm/mach-pxa/palmtx.c +++ b/arch/arm/mach-pxa/palmtx.c @@ -269,7 +269,7 @@ err: return ret; } -static int palmtx_backlight_notify(int brightness) +static int palmtx_backlight_notify(struct device *dev, int brightness) { gpio_set_value(GPIO_NR_PALMTX_BL_POWER, brightness); gpio_set_value(GPIO_NR_PALMTX_LCD_POWER, brightness); diff --git a/arch/arm/mach-pxa/palmz72.c b/arch/arm/mach-pxa/palmz72.c index d787ac7..1c5d68a 100644 --- a/arch/arm/mach-pxa/palmz72.c +++ b/arch/arm/mach-pxa/palmz72.c @@ -196,7 +196,7 @@ err: return ret; } -static int palmz72_backlight_notify(int brightness) +static int palmz72_backlight_notify(struct device *dev, int brightness) { gpio_set_value(GPIO_NR_PALMZ72_BL_POWER, brightness); gpio_set_value(GPIO_NR_PALMZ72_LCD_POWER, brightness); diff --git a/arch/arm/mach-pxa/spitz.c b/arch/arm/mach-pxa/spitz.c index 4b50f14..28352c0 100644 --- a/arch/arm/mach-pxa/spitz.c +++ b/arch/arm/mach-pxa/spitz.c @@ -389,13 +389,13 @@ static struct gpio_keys_button spitz_gpio_keys[] = { .type = EV_SW, .code = 0, .gpio = SPITZ_GPIO_SWA, - .desc = "Display Down", + .desc = "Display Down", }, { .type = EV_SW, .code = 1, .gpio = SPITZ_GPIO_SWB, - .desc = "Lid Closed", + .desc = "Lid Closed", }, }; diff --git a/arch/arm/mach-pxa/viper.c b/arch/arm/mach-pxa/viper.c index 5352b4e..89f258c 100644 --- a/arch/arm/mach-pxa/viper.c +++ b/arch/arm/mach-pxa/viper.c @@ -379,7 +379,7 @@ err_request_bckl: return ret; } -static int viper_backlight_notify(int brightness) +static int viper_backlight_notify(struct device *dev, int brightness) { gpio_set_value(VIPER_LCD_EN_GPIO, !!brightness); gpio_set_value(VIPER_BCKLIGHT_EN_GPIO, !!brightness); diff --git a/arch/arm/mach-realview/include/mach/board-pb1176.h b/arch/arm/mach-realview/include/mach/board-pb1176.h index 34b80b7..2f5ccb2 100644 --- a/arch/arm/mach-realview/include/mach/board-pb1176.h +++ b/arch/arm/mach-realview/include/mach/board-pb1176.h @@ -74,8 +74,8 @@ #define REALVIEW_PB1176_L220_BASE 0x10110000 /* L220 registers */ /* - * Control register SYS_RESETCTL is set to 1 to force a soft reset + * Control register SYS_RESETCTL Bit 8 is set to 1 to force a soft reset */ -#define REALVIEW_PB1176_SYS_LOCKVAL_RSTCTL 0x0100 +#define REALVIEW_PB1176_SYS_SOFT_RESET 0x0100 #endif /* __ASM_ARCH_BOARD_PB1176_H */ diff --git a/arch/arm/mach-realview/include/mach/platform.h b/arch/arm/mach-realview/include/mach/platform.h index 4f46bf7..86c0c44 100644 --- a/arch/arm/mach-realview/include/mach/platform.h +++ b/arch/arm/mach-realview/include/mach/platform.h @@ -140,7 +140,7 @@ * SYS_CLD, SYS_BOOTCS */ #define REALVIEW_SYS_LOCK_LOCKED (1 << 16) -#define REALVIEW_SYS_LOCKVAL_MASK 0xA05F /* Enable write access */ +#define REALVIEW_SYS_LOCK_VAL 0xA05F /* Enable write access */ /* * REALVIEW_SYS_FLASH diff --git a/arch/arm/mach-realview/realview_eb.c b/arch/arm/mach-realview/realview_eb.c index 917f8ca..7d857d3 100644 --- a/arch/arm/mach-realview/realview_eb.c +++ b/arch/arm/mach-realview/realview_eb.c @@ -381,6 +381,20 @@ static struct sys_timer realview_eb_timer = { .init = realview_eb_timer_init, }; +static void realview_eb_reset(char mode) +{ + void __iomem *reset_ctrl = __io_address(REALVIEW_SYS_RESETCTL); + void __iomem *lock_ctrl = __io_address(REALVIEW_SYS_LOCK); + + /* + * To reset, we hit the on-board reset register + * in the system FPGA + */ + __raw_writel(REALVIEW_SYS_LOCK_VAL, lock_ctrl); + if (core_tile_eb11mp()) + __raw_writel(0x0008, reset_ctrl); +} + static void __init realview_eb_init(void) { int i; @@ -408,6 +422,7 @@ static void __init realview_eb_init(void) #ifdef CONFIG_LEDS leds_event = realview_leds_event; #endif + realview_reset = realview_eb_reset; } MACHINE_START(REALVIEW_EB, "ARM-RealView EB") diff --git a/arch/arm/mach-realview/realview_pb1176.c b/arch/arm/mach-realview/realview_pb1176.c index 7fb726d..44392e5 100644 --- a/arch/arm/mach-realview/realview_pb1176.c +++ b/arch/arm/mach-realview/realview_pb1176.c @@ -292,12 +292,10 @@ static struct sys_timer realview_pb1176_timer = { static void realview_pb1176_reset(char mode) { - void __iomem *hdr_ctrl = __io_address(REALVIEW_SYS_BASE) + - REALVIEW_SYS_RESETCTL_OFFSET; - void __iomem *rst_hdr_ctrl = __io_address(REALVIEW_SYS_BASE) + - REALVIEW_SYS_LOCK_OFFSET; - __raw_writel(REALVIEW_SYS_LOCKVAL_MASK, rst_hdr_ctrl); - __raw_writel(REALVIEW_PB1176_SYS_LOCKVAL_RSTCTL, hdr_ctrl); + void __iomem *reset_ctrl = __io_address(REALVIEW_SYS_RESETCTL); + void __iomem *lock_ctrl = __io_address(REALVIEW_SYS_LOCK); + __raw_writel(REALVIEW_SYS_LOCK_VAL, lock_ctrl); + __raw_writel(REALVIEW_PB1176_SYS_SOFT_RESET, reset_ctrl); } static void realview_pb1176_fixup(struct machine_desc *mdesc, diff --git a/arch/arm/mach-realview/realview_pb11mp.c b/arch/arm/mach-realview/realview_pb11mp.c index 9bbbfc0..3e02731 100644 --- a/arch/arm/mach-realview/realview_pb11mp.c +++ b/arch/arm/mach-realview/realview_pb11mp.c @@ -301,17 +301,16 @@ static struct sys_timer realview_pb11mp_timer = { static void realview_pb11mp_reset(char mode) { - void __iomem *hdr_ctrl = __io_address(REALVIEW_SYS_BASE) + - REALVIEW_SYS_RESETCTL_OFFSET; - unsigned int val; + void __iomem *reset_ctrl = __io_address(REALVIEW_SYS_RESETCTL); + void __iomem *lock_ctrl = __io_address(REALVIEW_SYS_LOCK); /* * To reset, we hit the on-board reset register * in the system FPGA */ - val = __raw_readl(hdr_ctrl); - val |= REALVIEW_PB11MP_SYS_CTRL_RESET_CONFIGCLR; - __raw_writel(val, hdr_ctrl); + __raw_writel(REALVIEW_SYS_LOCK_VAL, lock_ctrl); + __raw_writel(0x0000, reset_ctrl); + __raw_writel(0x0004, reset_ctrl); } static void __init realview_pb11mp_init(void) diff --git a/arch/arm/mach-realview/realview_pba8.c b/arch/arm/mach-realview/realview_pba8.c index fe861e9..fe4e25c 100644 --- a/arch/arm/mach-realview/realview_pba8.c +++ b/arch/arm/mach-realview/realview_pba8.c @@ -272,6 +272,20 @@ static struct sys_timer realview_pba8_timer = { .init = realview_pba8_timer_init, }; +static void realview_pba8_reset(char mode) +{ + void __iomem *reset_ctrl = __io_address(REALVIEW_SYS_RESETCTL); + void __iomem *lock_ctrl = __io_address(REALVIEW_SYS_LOCK); + + /* + * To reset, we hit the on-board reset register + * in the system FPGA + */ + __raw_writel(REALVIEW_SYS_LOCK_VAL, lock_ctrl); + __raw_writel(0x0000, reset_ctrl); + __raw_writel(0x0004, reset_ctrl); +} + static void __init realview_pba8_init(void) { int i; @@ -291,6 +305,7 @@ static void __init realview_pba8_init(void) #ifdef CONFIG_LEDS leds_event = realview_leds_event; #endif + realview_reset = realview_pba8_reset; } MACHINE_START(REALVIEW_PBA8, "ARM-RealView PB-A8") diff --git a/arch/arm/mach-realview/realview_pbx.c b/arch/arm/mach-realview/realview_pbx.c index ec39488..d94857e 100644 --- a/arch/arm/mach-realview/realview_pbx.c +++ b/arch/arm/mach-realview/realview_pbx.c @@ -324,6 +324,20 @@ static void realview_pbx_fixup(struct machine_desc *mdesc, struct tag *tags, #endif } +static void realview_pbx_reset(char mode) +{ + void __iomem *reset_ctrl = __io_address(REALVIEW_SYS_RESETCTL); + void __iomem *lock_ctrl = __io_address(REALVIEW_SYS_LOCK); + + /* + * To reset, we hit the on-board reset register + * in the system FPGA + */ + __raw_writel(REALVIEW_SYS_LOCK_VAL, lock_ctrl); + __raw_writel(0x00F0, reset_ctrl); + __raw_writel(0x00F4, reset_ctrl); +} + static void __init realview_pbx_init(void) { int i; @@ -358,6 +372,7 @@ static void __init realview_pbx_init(void) #ifdef CONFIG_LEDS leds_event = realview_leds_event; #endif + realview_reset = realview_pbx_reset; } MACHINE_START(REALVIEW_PBX, "ARM-RealView PBX") diff --git a/arch/arm/mach-s3c2440/mach-mini2440.c b/arch/arm/mach-s3c2440/mach-mini2440.c index 547d4fc..2068e90 100644 --- a/arch/arm/mach-s3c2440/mach-mini2440.c +++ b/arch/arm/mach-s3c2440/mach-mini2440.c @@ -288,7 +288,7 @@ static struct s3c2410_platform_nand mini2440_nand_info __initdata = { /* DM9000AEP 10/100 ethernet controller */ -static struct resource mini2440_dm9k_resource[] __initdata = { +static struct resource mini2440_dm9k_resource[] = { [0] = { .start = MACH_MINI2440_DM9K_BASE, .end = MACH_MINI2440_DM9K_BASE + 3, @@ -310,11 +310,11 @@ static struct resource mini2440_dm9k_resource[] __initdata = { * The DM9000 has no eeprom, and it's MAC address is set by * the bootloader before starting the kernel. */ -static struct dm9000_plat_data mini2440_dm9k_pdata __initdata = { +static struct dm9000_plat_data mini2440_dm9k_pdata = { .flags = (DM9000_PLATF_16BITONLY | DM9000_PLATF_NO_EEPROM), }; -static struct platform_device mini2440_device_eth __initdata = { +static struct platform_device mini2440_device_eth = { .name = "dm9000", .id = -1, .num_resources = ARRAY_SIZE(mini2440_dm9k_resource), @@ -341,7 +341,7 @@ static struct platform_device mini2440_device_eth __initdata = { * | | +----+ +----+ * ..... */ -static struct gpio_keys_button mini2440_buttons[] __initdata = { +static struct gpio_keys_button mini2440_buttons[] = { { .gpio = S3C2410_GPG(0), /* K1 */ .code = KEY_F1, @@ -384,12 +384,12 @@ static struct gpio_keys_button mini2440_buttons[] __initdata = { #endif }; -static struct gpio_keys_platform_data mini2440_button_data __initdata = { +static struct gpio_keys_platform_data mini2440_button_data = { .buttons = mini2440_buttons, .nbuttons = ARRAY_SIZE(mini2440_buttons), }; -static struct platform_device mini2440_button_device __initdata = { +static struct platform_device mini2440_button_device = { .name = "gpio-keys", .id = -1, .dev = { @@ -399,41 +399,41 @@ static struct platform_device mini2440_button_device __initdata = { /* LEDS */ -static struct s3c24xx_led_platdata mini2440_led1_pdata __initdata = { +static struct s3c24xx_led_platdata mini2440_led1_pdata = { .name = "led1", .gpio = S3C2410_GPB(5), .flags = S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE, .def_trigger = "heartbeat", }; -static struct s3c24xx_led_platdata mini2440_led2_pdata __initdata = { +static struct s3c24xx_led_platdata mini2440_led2_pdata = { .name = "led2", .gpio = S3C2410_GPB(6), .flags = S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE, .def_trigger = "nand-disk", }; -static struct s3c24xx_led_platdata mini2440_led3_pdata __initdata = { +static struct s3c24xx_led_platdata mini2440_led3_pdata = { .name = "led3", .gpio = S3C2410_GPB(7), .flags = S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE, .def_trigger = "mmc0", }; -static struct s3c24xx_led_platdata mini2440_led4_pdata __initdata = { +static struct s3c24xx_led_platdata mini2440_led4_pdata = { .name = "led4", .gpio = S3C2410_GPB(8), .flags = S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE, .def_trigger = "", }; -static struct s3c24xx_led_platdata mini2440_led_backlight_pdata __initdata = { +static struct s3c24xx_led_platdata mini2440_led_backlight_pdata = { .name = "backlight", .gpio = S3C2410_GPG(4), .def_trigger = "backlight", }; -static struct platform_device mini2440_led1 __initdata = { +static struct platform_device mini2440_led1 = { .name = "s3c24xx_led", .id = 1, .dev = { @@ -441,7 +441,7 @@ static struct platform_device mini2440_led1 __initdata = { }, }; -static struct platform_device mini2440_led2 __initdata = { +static struct platform_device mini2440_led2 = { .name = "s3c24xx_led", .id = 2, .dev = { @@ -449,7 +449,7 @@ static struct platform_device mini2440_led2 __initdata = { }, }; -static struct platform_device mini2440_led3 __initdata = { +static struct platform_device mini2440_led3 = { .name = "s3c24xx_led", .id = 3, .dev = { @@ -457,7 +457,7 @@ static struct platform_device mini2440_led3 __initdata = { }, }; -static struct platform_device mini2440_led4 __initdata = { +static struct platform_device mini2440_led4 = { .name = "s3c24xx_led", .id = 4, .dev = { @@ -465,7 +465,7 @@ static struct platform_device mini2440_led4 __initdata = { }, }; -static struct platform_device mini2440_led_backlight __initdata = { +static struct platform_device mini2440_led_backlight = { .name = "s3c24xx_led", .id = 5, .dev = { @@ -475,14 +475,14 @@ static struct platform_device mini2440_led_backlight __initdata = { /* AUDIO */ -static struct s3c24xx_uda134x_platform_data mini2440_audio_pins __initdata = { +static struct s3c24xx_uda134x_platform_data mini2440_audio_pins = { .l3_clk = S3C2410_GPB(4), .l3_mode = S3C2410_GPB(2), .l3_data = S3C2410_GPB(3), .model = UDA134X_UDA1341 }; -static struct platform_device mini2440_audio __initdata = { +static struct platform_device mini2440_audio = { .name = "s3c24xx_uda134x", .id = 0, .dev = { diff --git a/arch/arm/mach-s3c6410/mach-hmt.c b/arch/arm/mach-s3c6410/mach-hmt.c index cdd4b53..7619456 100644 --- a/arch/arm/mach-s3c6410/mach-hmt.c +++ b/arch/arm/mach-s3c6410/mach-hmt.c @@ -82,7 +82,7 @@ static int hmt_bl_init(struct device *dev) return ret; } -static int hmt_bl_notify(int brightness) +static int hmt_bl_notify(struct device *dev, int brightness) { /* * translate from CIELUV/CIELAB L*->brightness, E.G. from diff --git a/arch/arm/mach-s3c6410/mach-smdk6410.c b/arch/arm/mach-s3c6410/mach-smdk6410.c index 480d297..8969fe7 100644 --- a/arch/arm/mach-s3c6410/mach-smdk6410.c +++ b/arch/arm/mach-s3c6410/mach-smdk6410.c @@ -211,6 +211,7 @@ static struct fixed_voltage_config smdk6410_b_pwr_5v_pdata = { .supply_name = "B_PWR_5V", .microvolts = 5000000, .init_data = &smdk6410_b_pwr_5v_data, + .gpio = -EINVAL, }; static struct platform_device smdk6410_b_pwr_5v = { diff --git a/arch/arm/mm/Makefile b/arch/arm/mm/Makefile index 827e238..e8d34a80 100644 --- a/arch/arm/mm/Makefile +++ b/arch/arm/mm/Makefile @@ -27,6 +27,9 @@ obj-$(CONFIG_CPU_ABRT_EV5TJ) += abort-ev5tj.o obj-$(CONFIG_CPU_ABRT_EV6) += abort-ev6.o obj-$(CONFIG_CPU_ABRT_EV7) += abort-ev7.o +AFLAGS_abort-ev6.o :=-Wa,-march=armv6k +AFLAGS_abort-ev7.o :=-Wa,-march=armv7-a + obj-$(CONFIG_CPU_PABRT_LEGACY) += pabort-legacy.o obj-$(CONFIG_CPU_PABRT_V6) += pabort-v6.o obj-$(CONFIG_CPU_PABRT_V7) += pabort-v7.o @@ -39,6 +42,9 @@ obj-$(CONFIG_CPU_CACHE_V6) += cache-v6.o obj-$(CONFIG_CPU_CACHE_V7) += cache-v7.o obj-$(CONFIG_CPU_CACHE_FA) += cache-fa.o +AFLAGS_cache-v6.o :=-Wa,-march=armv6 +AFLAGS_cache-v7.o :=-Wa,-march=armv7-a + obj-$(CONFIG_CPU_COPY_V3) += copypage-v3.o obj-$(CONFIG_CPU_COPY_V4WT) += copypage-v4wt.o obj-$(CONFIG_CPU_COPY_V4WB) += copypage-v4wb.o @@ -58,6 +64,9 @@ obj-$(CONFIG_CPU_TLB_V6) += tlb-v6.o obj-$(CONFIG_CPU_TLB_V7) += tlb-v7.o obj-$(CONFIG_CPU_TLB_FA) += tlb-fa.o +AFLAGS_tlb-v6.o :=-Wa,-march=armv6 +AFLAGS_tlb-v7.o :=-Wa,-march=armv7-a + obj-$(CONFIG_CPU_ARM610) += proc-arm6_7.o obj-$(CONFIG_CPU_ARM710) += proc-arm6_7.o obj-$(CONFIG_CPU_ARM7TDMI) += proc-arm7tdmi.o @@ -84,6 +93,9 @@ obj-$(CONFIG_CPU_FEROCEON) += proc-feroceon.o obj-$(CONFIG_CPU_V6) += proc-v6.o obj-$(CONFIG_CPU_V7) += proc-v7.o +AFLAGS_proc-v6.o :=-Wa,-march=armv6 +AFLAGS_proc-v7.o :=-Wa,-march=armv7-a + obj-$(CONFIG_CACHE_FEROCEON_L2) += cache-feroceon-l2.o obj-$(CONFIG_CACHE_L2X0) += cache-l2x0.o obj-$(CONFIG_CACHE_XSC3L2) += cache-xsc3l2.o diff --git a/arch/arm/mm/cache-xsc3l2.c b/arch/arm/mm/cache-xsc3l2.c index 5d180cb..c315492 100644 --- a/arch/arm/mm/cache-xsc3l2.c +++ b/arch/arm/mm/cache-xsc3l2.c @@ -221,15 +221,14 @@ static int __init xsc3_l2_init(void) if (!cpu_is_xsc3() || !xsc3_l2_present()) return 0; - if (!(get_cr() & CR_L2)) { + if (get_cr() & CR_L2) { pr_info("XScale3 L2 cache enabled.\n"); - adjust_cr(CR_L2, CR_L2); xsc3_l2_inv_all(); - } - outer_cache.inv_range = xsc3_l2_inv_range; - outer_cache.clean_range = xsc3_l2_clean_range; - outer_cache.flush_range = xsc3_l2_flush_range; + outer_cache.inv_range = xsc3_l2_inv_range; + outer_cache.clean_range = xsc3_l2_clean_range; + outer_cache.flush_range = xsc3_l2_flush_range; + } return 0; } diff --git a/arch/arm/mm/init.c b/arch/arm/mm/init.c index 52c40d1..a04ffbb 100644 --- a/arch/arm/mm/init.c +++ b/arch/arm/mm/init.c @@ -616,7 +616,7 @@ void __init mem_init(void) "%dK data, %dK init, %luK highmem)\n", nr_free_pages() << (PAGE_SHIFT-10), codesize >> 10, datasize >> 10, initsize >> 10, - (unsigned long) (totalhigh_pages << (PAGE_SHIFT-10))); + totalhigh_pages << (PAGE_SHIFT-10)); if (PAGE_SIZE >= 16384 && num_physpages <= 128) { extern int sysctl_overcommit_memory; diff --git a/arch/arm/mm/mmu.c b/arch/arm/mm/mmu.c index 1708da8..761ffed 100644 --- a/arch/arm/mm/mmu.c +++ b/arch/arm/mm/mmu.c @@ -1067,4 +1067,6 @@ void setup_mm_for_reboot(char mode) pmd[1] = __pmd(pmdval + (1 << (PGDIR_SHIFT - 1))); flush_pmd_entry(pmd); } + + local_flush_tlb_all(); } diff --git a/arch/arm/mm/proc-arm6_7.S b/arch/arm/mm/proc-arm6_7.S index 3f9cd3d..795dc61 100644 --- a/arch/arm/mm/proc-arm6_7.S +++ b/arch/arm/mm/proc-arm6_7.S @@ -41,7 +41,7 @@ ENTRY(cpu_arm7_dcache_clean_area) ENTRY(cpu_arm7_data_abort) mrc p15, 0, r1, c5, c0, 0 @ get FSR mrc p15, 0, r0, c6, c0, 0 @ get FAR - ldr r8, [r0] @ read arm instruction + ldr r8, [r2] @ read arm instruction tst r8, #1 << 20 @ L = 0 -> write? orreq r1, r1, #1 << 11 @ yes. and r7, r8, #15 << 24 diff --git a/arch/arm/mm/proc-v6.S b/arch/arm/mm/proc-v6.S index 395cc90..7a5337e 100644 --- a/arch/arm/mm/proc-v6.S +++ b/arch/arm/mm/proc-v6.S @@ -59,8 +59,6 @@ ENTRY(cpu_v6_proc_fin) * to what would be the reset vector. * * - loc - location to jump to for soft reset - * - * It is assumed that: */ .align 5 ENTRY(cpu_v6_reset) diff --git a/arch/arm/mm/proc-v7.S b/arch/arm/mm/proc-v7.S index 3a28521..7aaf88a 100644 --- a/arch/arm/mm/proc-v7.S +++ b/arch/arm/mm/proc-v7.S @@ -45,7 +45,14 @@ ENTRY(cpu_v7_proc_init) ENDPROC(cpu_v7_proc_init) ENTRY(cpu_v7_proc_fin) - mov pc, lr + stmfd sp!, {lr} + cpsid if @ disable interrupts + bl v7_flush_kern_cache_all + mrc p15, 0, r0, c1, c0, 0 @ ctrl register + bic r0, r0, #0x1000 @ ...i............ + bic r0, r0, #0x0006 @ .............ca. + mcr p15, 0, r0, c1, c0, 0 @ disable caches + ldmfd sp!, {pc} ENDPROC(cpu_v7_proc_fin) /* @@ -56,8 +63,6 @@ ENDPROC(cpu_v7_proc_fin) * to what would be the reset vector. * * - loc - location to jump to for soft reset - * - * It is assumed that: */ .align 5 ENTRY(cpu_v7_reset) diff --git a/arch/arm/mm/proc-xsc3.S b/arch/arm/mm/proc-xsc3.S index 96456f5..8e4f6dc 100644 --- a/arch/arm/mm/proc-xsc3.S +++ b/arch/arm/mm/proc-xsc3.S @@ -407,6 +407,13 @@ __xsc3_setup: adr r5, xsc3_crval ldmia r5, {r5, r6} + +#ifdef CONFIG_CACHE_XSC3L2 + mrc p15, 1, r0, c0, c0, 1 @ get L2 present information + ands r0, r0, #0xf8 + orrne r6, r6, #(1 << 26) @ enable L2 if present +#endif + mrc p15, 0, r0, c1, c0, 0 @ get control register bic r0, r0, r5 @ ..V. ..R. .... ..A. orr r0, r0, r6 @ ..VI Z..S .... .C.M (mmu) diff --git a/arch/arm/plat-mxc/audmux-v2.c b/arch/arm/plat-mxc/audmux-v2.c index 6f21096..b06954a 100644 --- a/arch/arm/plat-mxc/audmux-v2.c +++ b/arch/arm/plat-mxc/audmux-v2.c @@ -23,6 +23,7 @@ #include <linux/err.h> #include <linux/io.h> #include <linux/clk.h> +#include <linux/debugfs.h> #include <mach/audmux.h> #include <mach/hardware.h> @@ -32,6 +33,140 @@ static void __iomem *audmux_base; #define MXC_AUDMUX_V2_PTCR(x) ((x) * 8) #define MXC_AUDMUX_V2_PDCR(x) ((x) * 8 + 4) +#ifdef CONFIG_DEBUG_FS +static struct dentry *audmux_debugfs_root; + +static int audmux_open_file(struct inode *inode, struct file *file) +{ + file->private_data = inode->i_private; + return 0; +} + +/* There is an annoying discontinuity in the SSI numbering with regard + * to the Linux number of the devices */ +static const char *audmux_port_string(int port) +{ + switch (port) { + case MX31_AUDMUX_PORT1_SSI0: + return "imx-ssi.0"; + case MX31_AUDMUX_PORT2_SSI1: + return "imx-ssi.1"; + case MX31_AUDMUX_PORT3_SSI_PINS_3: + return "SSI3"; + case MX31_AUDMUX_PORT4_SSI_PINS_4: + return "SSI4"; + case MX31_AUDMUX_PORT5_SSI_PINS_5: + return "SSI5"; + case MX31_AUDMUX_PORT6_SSI_PINS_6: + return "SSI6"; + default: + return "UNKNOWN"; + } +} + +static ssize_t audmux_read_file(struct file *file, char __user *user_buf, + size_t count, loff_t *ppos) +{ + ssize_t ret; + char *buf = kmalloc(PAGE_SIZE, GFP_KERNEL); + int port = (int)file->private_data; + u32 pdcr, ptcr; + + if (!buf) + return -ENOMEM; + + if (audmux_clk) + clk_enable(audmux_clk); + + ptcr = readl(audmux_base + MXC_AUDMUX_V2_PTCR(port)); + pdcr = readl(audmux_base + MXC_AUDMUX_V2_PDCR(port)); + + if (audmux_clk) + clk_disable(audmux_clk); + + ret = snprintf(buf, PAGE_SIZE, "PDCR: %08x\nPTCR: %08x\n", + pdcr, ptcr); + + if (ptcr & MXC_AUDMUX_V2_PTCR_TFSDIR) + ret += snprintf(buf + ret, PAGE_SIZE - ret, + "TxFS output from %s, ", + audmux_port_string((ptcr >> 27) & 0x7)); + else + ret += snprintf(buf + ret, PAGE_SIZE - ret, + "TxFS input, "); + + if (ptcr & MXC_AUDMUX_V2_PTCR_TCLKDIR) + ret += snprintf(buf + ret, PAGE_SIZE - ret, + "TxClk output from %s", + audmux_port_string((ptcr >> 22) & 0x7)); + else + ret += snprintf(buf + ret, PAGE_SIZE - ret, + "TxClk input"); + + ret += snprintf(buf + ret, PAGE_SIZE - ret, "\n"); + + if (ptcr & MXC_AUDMUX_V2_PTCR_SYN) { + ret += snprintf(buf + ret, PAGE_SIZE - ret, + "Port is symmetric"); + } else { + if (ptcr & MXC_AUDMUX_V2_PTCR_RFSDIR) + ret += snprintf(buf + ret, PAGE_SIZE - ret, + "RxFS output from %s, ", + audmux_port_string((ptcr >> 17) & 0x7)); + else + ret += snprintf(buf + ret, PAGE_SIZE - ret, + "RxFS input, "); + + if (ptcr & MXC_AUDMUX_V2_PTCR_RCLKDIR) + ret += snprintf(buf + ret, PAGE_SIZE - ret, + "RxClk output from %s", + audmux_port_string((ptcr >> 12) & 0x7)); + else + ret += snprintf(buf + ret, PAGE_SIZE - ret, + "RxClk input"); + } + + ret += snprintf(buf + ret, PAGE_SIZE - ret, + "\nData received from %s\n", + audmux_port_string((pdcr >> 13) & 0x7)); + + ret = simple_read_from_buffer(user_buf, count, ppos, buf, ret); + + kfree(buf); + + return ret; +} + +static const struct file_operations audmux_debugfs_fops = { + .open = audmux_open_file, + .read = audmux_read_file, +}; + +static void audmux_debugfs_init(void) +{ + int i; + char buf[20]; + + audmux_debugfs_root = debugfs_create_dir("audmux", NULL); + if (!audmux_debugfs_root) { + pr_warning("Failed to create AUDMUX debugfs root\n"); + return; + } + + for (i = 1; i < 8; i++) { + snprintf(buf, sizeof(buf), "ssi%d", i); + if (!debugfs_create_file(buf, 0444, audmux_debugfs_root, + (void *)i, &audmux_debugfs_fops)) + pr_warning("Failed to create AUDMUX port %d debugfs file\n", + i); + } +} +#else +static inline void audmux_debugfs_init(void) +{ +} +#endif + int mxc_audmux_v2_configure_port(unsigned int port, unsigned int ptcr, unsigned int pdcr) { @@ -68,6 +203,8 @@ static int mxc_audmux_v2_init(void) if (cpu_is_mx31() || cpu_is_mx35()) audmux_base = IO_ADDRESS(AUDMUX_BASE_ADDR); + audmux_debugfs_init(); + return 0; } diff --git a/arch/arm/plat-mxc/include/mach/board-mx31lite.h b/arch/arm/plat-mxc/include/mach/board-mx31lite.h index 0184b63..2b2da03 100644 --- a/arch/arm/plat-mxc/include/mach/board-mx31lite.h +++ b/arch/arm/plat-mxc/include/mach/board-mx31lite.h @@ -25,7 +25,7 @@ #ifndef __ASSEMBLY__ -enum mx31lilly_boards { +enum mx31lite_boards { MX31LITE_NOBOARD = 0, MX31LITE_DB = 1, }; diff --git a/arch/arm/plat-mxc/include/mach/common.h b/arch/arm/plat-mxc/include/mach/common.h index 286cb9b..4bf1068 100644 --- a/arch/arm/plat-mxc/include/mach/common.h +++ b/arch/arm/plat-mxc/include/mach/common.h @@ -32,7 +32,7 @@ extern void mxc91231_init_irq(void); extern void mxc_timer_init(struct clk *timer_clk, void __iomem *, int); extern int mx1_clocks_init(unsigned long fref); extern int mx21_clocks_init(unsigned long lref, unsigned long fref); -extern int mx25_clocks_init(unsigned long fref); +extern int mx25_clocks_init(void); extern int mx27_clocks_init(unsigned long fref); extern int mx31_clocks_init(unsigned long fref); extern int mx35_clocks_init(void); diff --git a/arch/arm/plat-mxc/include/mach/iomux-mx35.h b/arch/arm/plat-mxc/include/mach/iomux-mx35.h index 00b0ac1..c88d407 100644 --- a/arch/arm/plat-mxc/include/mach/iomux-mx35.h +++ b/arch/arm/plat-mxc/include/mach/iomux-mx35.h @@ -671,7 +671,7 @@ #define MX35_PAD_LD8__SDMA_SDMA_DEBUG_PC_8 IOMUX_PAD(0x634, 0x1d0, 6, 0x0, 0, NO_PAD_CTRL) #define MX35_PAD_LD9__IPU_DISPB_DAT_9 IOMUX_PAD(0x638, 0x1d4, 0, 0x0, 0, NO_PAD_CTRL) -#define MX35_PAD_LD9__GPIO2_9 IOMUX_PAD(0x638, 0x1d4, 5, 0x8e4 0, NO_PAD_CTRL) +#define MX35_PAD_LD9__GPIO2_9 IOMUX_PAD(0x638, 0x1d4, 5, 0x8e4, 0, NO_PAD_CTRL) #define MX35_PAD_LD9__SDMA_SDMA_DEBUG_PC_9 IOMUX_PAD(0x638, 0x1d4, 6, 0x0, 0, NO_PAD_CTRL) #define MX35_PAD_LD10__IPU_DISPB_DAT_10 IOMUX_PAD(0x63c, 0x1d8, 0, 0x0, 0, NO_PAD_CTRL) diff --git a/arch/arm/plat-mxc/include/mach/irqs.h b/arch/arm/plat-mxc/include/mach/irqs.h index ead9d59..0cb3476 100644 --- a/arch/arm/plat-mxc/include/mach/irqs.h +++ b/arch/arm/plat-mxc/include/mach/irqs.h @@ -37,7 +37,12 @@ * within sensible limits. */ #define MXC_BOARD_IRQ_START (MXC_INTERNAL_IRQS + MXC_GPIO_IRQS) + +#ifdef CONFIG_MACH_MX31ADS_WM1133_EV1 +#define MXC_BOARD_IRQS 80 +#else #define MXC_BOARD_IRQS 16 +#endif #define MXC_IPU_IRQ_START (MXC_BOARD_IRQ_START + MXC_BOARD_IRQS) diff --git a/arch/arm/plat-mxc/include/mach/uncompress.h b/arch/arm/plat-mxc/include/mach/uncompress.h index 4d5d395..d49384c 100644 --- a/arch/arm/plat-mxc/include/mach/uncompress.h +++ b/arch/arm/plat-mxc/include/mach/uncompress.h @@ -60,7 +60,9 @@ static void putc(int ch) UART(TXR) = ch; } -#define flush() do { } while (0) +static inline void flush(void) +{ +} #define MX1_UART1_BASE_ADDR 0x00206000 #define MX25_UART1_BASE_ADDR 0x43f90000 diff --git a/arch/arm/plat-omap/clock.c b/arch/arm/plat-omap/clock.c index 89cafc9..4becbdd 100644 --- a/arch/arm/plat-omap/clock.c +++ b/arch/arm/plat-omap/clock.c @@ -36,10 +36,6 @@ static struct clk_functions *arch_clock; * Standard clock functions defined in include/linux/clk.h *-------------------------------------------------------------------------*/ -/* This functions is moved to arch/arm/common/clkdev.c. For OMAP4 since - * clock framework is not up , it is defined here to avoid rework in - * every driver. Also dummy prcm reset function is added */ - int clk_enable(struct clk *clk) { unsigned long flags; @@ -305,7 +301,6 @@ void clk_enable_init_clocks(void) clk_enable(clkp); } } -EXPORT_SYMBOL(clk_enable_init_clocks); /* * Low level helpers @@ -334,7 +329,16 @@ void clk_init_cpufreq_table(struct cpufreq_frequency_table **table) arch_clock->clk_init_cpufreq_table(table); spin_unlock_irqrestore(&clockfw_lock, flags); } -EXPORT_SYMBOL(clk_init_cpufreq_table); + +void clk_exit_cpufreq_table(struct cpufreq_frequency_table **table) +{ + unsigned long flags; + + spin_lock_irqsave(&clockfw_lock, flags); + if (arch_clock->clk_exit_cpufreq_table) + arch_clock->clk_exit_cpufreq_table(table); + spin_unlock_irqrestore(&clockfw_lock, flags); +} #endif /*-------------------------------------------------------------------------*/ @@ -387,7 +391,7 @@ static struct dentry *clk_debugfs_root; static int clk_debugfs_register_one(struct clk *c) { int err; - struct dentry *d, *child; + struct dentry *d, *child, *child_tmp; struct clk *pa = c->parent; char s[255]; char *p = s; @@ -419,7 +423,7 @@ static int clk_debugfs_register_one(struct clk *c) err_out: d = c->dent; - list_for_each_entry(child, &d->d_subdirs, d_u.d_child) + list_for_each_entry_safe(child, child_tmp, &d->d_subdirs, d_u.d_child) debugfs_remove(child); debugfs_remove(c->dent); return err; diff --git a/arch/arm/plat-omap/common.c b/arch/arm/plat-omap/common.c index bf1eaf3..dddc027 100644 --- a/arch/arm/plat-omap/common.c +++ b/arch/arm/plat-omap/common.c @@ -172,6 +172,32 @@ unsigned long long sched_clock(void) clocksource_32k.mult, clocksource_32k.shift); } +/** + * read_persistent_clock - Return time from a persistent clock. + * + * Reads the time from a source which isn't disabled during PM, the + * 32k sync timer. Convert the cycles elapsed since last read into + * nsecs and adds to a monotonically increasing timespec. + */ +static struct timespec persistent_ts; +static cycles_t cycles, last_cycles; +void read_persistent_clock(struct timespec *ts) +{ + unsigned long long nsecs; + cycles_t delta; + struct timespec *tsp = &persistent_ts; + + last_cycles = cycles; + cycles = clocksource_32k.read(&clocksource_32k); + delta = cycles - last_cycles; + + nsecs = clocksource_cyc2ns(delta, + clocksource_32k.mult, clocksource_32k.shift); + + timespec_add_ns(tsp, nsecs); + *ts = *tsp; +} + static int __init omap_init_clocksource_32k(void) { static char err[] __initdata = KERN_ERR diff --git a/arch/arm/plat-omap/cpu-omap.c b/arch/arm/plat-omap/cpu-omap.c index f8ddbdd..6d3d333 100644 --- a/arch/arm/plat-omap/cpu-omap.c +++ b/arch/arm/plat-omap/cpu-omap.c @@ -134,6 +134,7 @@ static int __init omap_cpu_init(struct cpufreq_policy *policy) static int omap_cpu_exit(struct cpufreq_policy *policy) { + clk_exit_cpufreq_table(&freq_table); clk_put(mpu_clk); return 0; } diff --git a/arch/arm/plat-omap/dma.c b/arch/arm/plat-omap/dma.c index 09d82b3..728c642 100644 --- a/arch/arm/plat-omap/dma.c +++ b/arch/arm/plat-omap/dma.c @@ -1183,7 +1183,7 @@ void omap_dma_unlink_lch(int lch_head, int lch_queue) } if ((dma_chan[lch_head].flags & OMAP_DMA_ACTIVE) || - (dma_chan[lch_head].flags & OMAP_DMA_ACTIVE)) { + (dma_chan[lch_queue].flags & OMAP_DMA_ACTIVE)) { printk(KERN_ERR "omap_dma: You need to stop the DMA channels " "before unlinking\n"); dump_stack(); diff --git a/arch/arm/plat-omap/dmtimer.c b/arch/arm/plat-omap/dmtimer.c index 64f407e..08ccf89 100644 --- a/arch/arm/plat-omap/dmtimer.c +++ b/arch/arm/plat-omap/dmtimer.c @@ -551,6 +551,19 @@ void omap_dm_timer_stop(struct omap_dm_timer *timer) if (l & OMAP_TIMER_CTRL_ST) { l &= ~0x1; omap_dm_timer_write_reg(timer, OMAP_TIMER_CTRL_REG, l); +#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) || \ + defined(CONFIG_ARCH_OMAP4) + /* Readback to make sure write has completed */ + omap_dm_timer_read_reg(timer, OMAP_TIMER_CTRL_REG); + /* + * Wait for functional clock period x 3.5 to make sure that + * timer is stopped + */ + udelay(3500000 / clk_get_rate(timer->fclk) + 1); + /* Ack possibly pending interrupt */ + omap_dm_timer_write_reg(timer, OMAP_TIMER_STAT_REG, + OMAP_TIMER_INT_OVERFLOW); +#endif } } EXPORT_SYMBOL_GPL(omap_dm_timer_stop); diff --git a/arch/arm/plat-omap/gpio.c b/arch/arm/plat-omap/gpio.c index 0484681..d2422c7 100644 --- a/arch/arm/plat-omap/gpio.c +++ b/arch/arm/plat-omap/gpio.c @@ -192,6 +192,7 @@ struct gpio_bank { u32 saved_risingdetect; #endif u32 level_mask; + u32 toggle_mask; spinlock_t lock; struct gpio_chip chip; struct clk *dbck; @@ -749,6 +750,44 @@ static inline void set_24xx_gpio_triggering(struct gpio_bank *bank, int gpio, } #endif +#ifdef CONFIG_ARCH_OMAP1 +/* + * This only applies to chips that can't do both rising and falling edge + * detection at once. For all other chips, this function is a noop. + */ +static void _toggle_gpio_edge_triggering(struct gpio_bank *bank, int gpio) +{ + void __iomem *reg = bank->base; + u32 l = 0; + + switch (bank->method) { + case METHOD_MPUIO: + reg += OMAP_MPUIO_GPIO_INT_EDGE; + break; +#ifdef CONFIG_ARCH_OMAP15XX + case METHOD_GPIO_1510: + reg += OMAP1510_GPIO_INT_CONTROL; + break; +#endif +#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850) + case METHOD_GPIO_7XX: + reg += OMAP7XX_GPIO_INT_CONTROL; + break; +#endif + default: + return; + } + + l = __raw_readl(reg); + if ((l >> gpio) & 1) + l &= ~(1 << gpio); + else + l |= 1 << gpio; + + __raw_writel(l, reg); +} +#endif + static int _set_gpio_triggering(struct gpio_bank *bank, int gpio, int trigger) { void __iomem *reg = bank->base; @@ -759,6 +798,8 @@ static int _set_gpio_triggering(struct gpio_bank *bank, int gpio, int trigger) case METHOD_MPUIO: reg += OMAP_MPUIO_GPIO_INT_EDGE; l = __raw_readl(reg); + if (trigger & IRQ_TYPE_EDGE_BOTH) + bank->toggle_mask |= 1 << gpio; if (trigger & IRQ_TYPE_EDGE_RISING) l |= 1 << gpio; else if (trigger & IRQ_TYPE_EDGE_FALLING) @@ -771,6 +812,8 @@ static int _set_gpio_triggering(struct gpio_bank *bank, int gpio, int trigger) case METHOD_GPIO_1510: reg += OMAP1510_GPIO_INT_CONTROL; l = __raw_readl(reg); + if (trigger & IRQ_TYPE_EDGE_BOTH) + bank->toggle_mask |= 1 << gpio; if (trigger & IRQ_TYPE_EDGE_RISING) l |= 1 << gpio; else if (trigger & IRQ_TYPE_EDGE_FALLING) @@ -803,6 +846,8 @@ static int _set_gpio_triggering(struct gpio_bank *bank, int gpio, int trigger) case METHOD_GPIO_7XX: reg += OMAP7XX_GPIO_INT_CONTROL; l = __raw_readl(reg); + if (trigger & IRQ_TYPE_EDGE_BOTH) + bank->toggle_mask |= 1 << gpio; if (trigger & IRQ_TYPE_EDGE_RISING) l |= 1 << gpio; else if (trigger & IRQ_TYPE_EDGE_FALLING) @@ -1072,7 +1117,7 @@ static inline void _set_gpio_irqenable(struct gpio_bank *bank, int gpio, int ena */ static int _set_gpio_wakeup(struct gpio_bank *bank, int gpio, int enable) { - unsigned long flags; + unsigned long uninitialized_var(flags); switch (bank->method) { #ifdef CONFIG_ARCH_OMAP16XX @@ -1217,7 +1262,7 @@ static void gpio_irq_handler(unsigned int irq, struct irq_desc *desc) { void __iomem *isr_reg = NULL; u32 isr; - unsigned int gpio_irq; + unsigned int gpio_irq, gpio_index; struct gpio_bank *bank; u32 retrigger = 0; int unmasked = 0; @@ -1284,9 +1329,23 @@ static void gpio_irq_handler(unsigned int irq, struct irq_desc *desc) gpio_irq = bank->virtual_irq_start; for (; isr != 0; isr >>= 1, gpio_irq++) { + gpio_index = get_gpio_index(irq_to_gpio(gpio_irq)); + if (!(isr & 1)) continue; +#ifdef CONFIG_ARCH_OMAP1 + /* + * Some chips can't respond to both rising and falling + * at the same time. If this irq was requested with + * both flags, we need to flip the ICR data for the IRQ + * to respond to the IRQ for the opposite direction. + * This will be indicated in the bank toggle_mask. + */ + if (bank->toggle_mask & (1 << gpio_index)) + _toggle_gpio_edge_triggering(bank, gpio_index); +#endif + generic_handle_irq(gpio_irq); } } diff --git a/arch/arm/plat-omap/include/plat/board.h b/arch/arm/plat-omap/include/plat/board.h index 376ce18..5cd6220 100644 --- a/arch/arm/plat-omap/include/plat/board.h +++ b/arch/arm/plat-omap/include/plat/board.h @@ -99,7 +99,6 @@ struct fb_info; struct omap_backlight_config { int default_intensity; int (*set_power)(struct device *dev, int state); - int (*check_fb)(struct fb_info *fb); }; struct omap_fbmem_config { diff --git a/arch/arm/plat-omap/include/plat/clock.h b/arch/arm/plat-omap/include/plat/clock.h index 309b6d1..94fe2a0 100644 --- a/arch/arm/plat-omap/include/plat/clock.h +++ b/arch/arm/plat-omap/include/plat/clock.h @@ -119,6 +119,7 @@ struct clk_functions { void (*clk_disable_unused)(struct clk *clk); #ifdef CONFIG_CPU_FREQ void (*clk_init_cpufreq_table)(struct cpufreq_frequency_table **); + void (*clk_exit_cpufreq_table)(struct cpufreq_frequency_table **); #endif }; @@ -135,6 +136,7 @@ extern unsigned long followparent_recalc(struct clk *clk); extern void clk_enable_init_clocks(void); #ifdef CONFIG_CPU_FREQ extern void clk_init_cpufreq_table(struct cpufreq_frequency_table **table); +extern void clk_exit_cpufreq_table(struct cpufreq_frequency_table **table); #endif extern const struct clkops clkops_null; diff --git a/arch/arm/plat-omap/include/plat/control.h b/arch/arm/plat-omap/include/plat/control.h index 2ae8843..a745d62 100644 --- a/arch/arm/plat-omap/include/plat/control.h +++ b/arch/arm/plat-omap/include/plat/control.h @@ -147,7 +147,7 @@ #define OMAP343X_CONTROL_IVA2_BOOTADDR (OMAP2_CONTROL_GENERAL + 0x0190) #define OMAP343X_CONTROL_IVA2_BOOTMOD (OMAP2_CONTROL_GENERAL + 0x0194) #define OMAP343X_CONTROL_DEBOBS(i) (OMAP2_CONTROL_GENERAL + 0x01B0 \ - + ((i) >> 1) * 4 + (!(i) & 1) * 2) + + ((i) >> 1) * 4 + (!((i) & 1)) * 2) #define OMAP343X_CONTROL_PROG_IO0 (OMAP2_CONTROL_GENERAL + 0x01D4) #define OMAP343X_CONTROL_PROG_IO1 (OMAP2_CONTROL_GENERAL + 0x01D8) #define OMAP343X_CONTROL_DSS_DPLL_SPREADING (OMAP2_CONTROL_GENERAL + 0x01E0) diff --git a/arch/arm/plat-omap/include/plat/cpu.h b/arch/arm/plat-omap/include/plat/cpu.h index 9a028bd..a162f58 100644 --- a/arch/arm/plat-omap/include/plat/cpu.h +++ b/arch/arm/plat-omap/include/plat/cpu.h @@ -434,6 +434,7 @@ IS_OMAP_TYPE(3517, 0x3517) #define OMAP3430_REV_ES2_1 0x34302034 #define OMAP3430_REV_ES3_0 0x34303034 #define OMAP3430_REV_ES3_1 0x34304034 +#define OMAP3430_REV_ES3_1_2 0x34305034 #define OMAP3630_REV_ES1_0 0x36300034 diff --git a/arch/arm/plat-omap/include/plat/io.h b/arch/arm/plat-omap/include/plat/io.h index 7e5319f..a3e7b47 100644 --- a/arch/arm/plat-omap/include/plat/io.h +++ b/arch/arm/plat-omap/include/plat/io.h @@ -122,16 +122,21 @@ #define OMAP243X_SMS_VIRT (OMAP243X_SMS_PHYS + OMAP2_L3_IO_OFFSET) #define OMAP243X_SMS_SIZE SZ_1M -/* DSP */ -#define DSP_MEM_24XX_PHYS OMAP2420_DSP_MEM_BASE /* 0x58000000 */ -#define DSP_MEM_24XX_VIRT 0xe0000000 -#define DSP_MEM_24XX_SIZE 0x28000 -#define DSP_IPI_24XX_PHYS OMAP2420_DSP_IPI_BASE /* 0x59000000 */ -#define DSP_IPI_24XX_VIRT 0xe1000000 -#define DSP_IPI_24XX_SIZE SZ_4K -#define DSP_MMU_24XX_PHYS OMAP2420_DSP_MMU_BASE /* 0x5a000000 */ -#define DSP_MMU_24XX_VIRT 0xe2000000 -#define DSP_MMU_24XX_SIZE SZ_4K +/* 2420 IVA */ +#define DSP_MEM_2420_PHYS OMAP2420_DSP_MEM_BASE + /* 0x58000000 --> 0xfc100000 */ +#define DSP_MEM_2420_VIRT 0xfc100000 +#define DSP_MEM_2420_SIZE 0x28000 +#define DSP_IPI_2420_PHYS OMAP2420_DSP_IPI_BASE + /* 0x59000000 --> 0xfc128000 */ +#define DSP_IPI_2420_VIRT 0xfc128000 +#define DSP_IPI_2420_SIZE SZ_4K +#define DSP_MMU_2420_PHYS OMAP2420_DSP_MMU_BASE + /* 0x5a000000 --> 0xfc129000 */ +#define DSP_MMU_2420_VIRT 0xfc129000 +#define DSP_MMU_2420_SIZE SZ_4K + +/* 2430 IVA2.1 - currently unmapped */ /* * ---------------------------------------------------------------------------- @@ -182,16 +187,7 @@ #define OMAP343X_SDRC_VIRT (OMAP343X_SDRC_PHYS + OMAP2_L3_IO_OFFSET) #define OMAP343X_SDRC_SIZE SZ_1M -/* DSP */ -#define DSP_MEM_34XX_PHYS OMAP34XX_DSP_MEM_BASE /* 0x58000000 */ -#define DSP_MEM_34XX_VIRT 0xe0000000 -#define DSP_MEM_34XX_SIZE 0x28000 -#define DSP_IPI_34XX_PHYS OMAP34XX_DSP_IPI_BASE /* 0x59000000 */ -#define DSP_IPI_34XX_VIRT 0xe1000000 -#define DSP_IPI_34XX_SIZE SZ_4K -#define DSP_MMU_34XX_PHYS OMAP34XX_DSP_MMU_BASE /* 0x5a000000 */ -#define DSP_MMU_34XX_VIRT 0xe2000000 -#define DSP_MMU_34XX_SIZE SZ_4K +/* 3430 IVA - currently unmapped */ /* * ---------------------------------------------------------------------------- diff --git a/arch/arm/plat-omap/include/plat/irqs.h b/arch/arm/plat-omap/include/plat/irqs.h index 97d6c50c3..c0ab7c8 100644 --- a/arch/arm/plat-omap/include/plat/irqs.h +++ b/arch/arm/plat-omap/include/plat/irqs.h @@ -499,6 +499,9 @@ extern void omap_init_irq(void); extern int omap_irq_pending(void); void omap_intc_save_context(void); void omap_intc_restore_context(void); +void omap3_intc_suspend(void); +void omap3_intc_prepare_idle(void); +void omap3_intc_resume_idle(void); #endif #include <mach/hardware.h> diff --git a/arch/arm/plat-omap/include/plat/mux.h b/arch/arm/plat-omap/include/plat/mux.h index 8f069cc..692c90e 100644 --- a/arch/arm/plat-omap/include/plat/mux.h +++ b/arch/arm/plat-omap/include/plat/mux.h @@ -183,6 +183,14 @@ enum omap7xx_index { /* I2C */ I2C_7XX_SCL, I2C_7XX_SDA, + + /* SPI */ + SPI_7XX_1, + SPI_7XX_2, + SPI_7XX_3, + SPI_7XX_4, + SPI_7XX_5, + SPI_7XX_6, }; enum omap1xxx_index { diff --git a/arch/arm/plat-omap/include/plat/omap7xx.h b/arch/arm/plat-omap/include/plat/omap7xx.h index 53f5241..48e4757 100644 --- a/arch/arm/plat-omap/include/plat/omap7xx.h +++ b/arch/arm/plat-omap/include/plat/omap7xx.h @@ -46,6 +46,9 @@ #define OMAP7XX_DSPREG_SIZE SZ_128K #define OMAP7XX_DSPREG_START 0xE1000000 +#define OMAP7XX_SPI1_BASE 0xfffc0800 +#define OMAP7XX_SPI2_BASE 0xfffc1000 + /* * ---------------------------------------------------------------------------- * OMAP7XX specific configuration registers diff --git a/arch/arm/plat-omap/include/plat/omap_hwmod.h b/arch/arm/plat-omap/include/plat/omap_hwmod.h index 007935a..3393325 100644 --- a/arch/arm/plat-omap/include/plat/omap_hwmod.h +++ b/arch/arm/plat-omap/include/plat/omap_hwmod.h @@ -227,6 +227,7 @@ struct omap_hwmod_ocp_if { #define SYSC_HAS_SIDLEMODE (1 << 5) #define SYSC_HAS_MIDLEMODE (1 << 6) #define SYSS_MISSING (1 << 7) +#define SYSC_NO_CACHE (1 << 8) /* XXX SW flag, belongs elsewhere */ /* omap_hwmod_sysconfig.clockact flags */ #define CLOCKACT_TEST_BOTH 0x0 diff --git a/arch/arm/plat-omap/io.c b/arch/arm/plat-omap/io.c index 11f5d79..0cfd54f 100644 --- a/arch/arm/plat-omap/io.c +++ b/arch/arm/plat-omap/io.c @@ -66,12 +66,12 @@ void __iomem *omap_ioremap(unsigned long p, size_t size, unsigned int type) return XLATE(p, L4_24XX_PHYS, L4_24XX_VIRT); } if (cpu_is_omap2420()) { - if (BETWEEN(p, DSP_MEM_24XX_PHYS, DSP_MEM_24XX_SIZE)) - return XLATE(p, DSP_MEM_24XX_PHYS, DSP_MEM_24XX_VIRT); - if (BETWEEN(p, DSP_IPI_24XX_PHYS, DSP_IPI_24XX_SIZE)) - return XLATE(p, DSP_IPI_24XX_PHYS, DSP_IPI_24XX_SIZE); - if (BETWEEN(p, DSP_MMU_24XX_PHYS, DSP_MMU_24XX_SIZE)) - return XLATE(p, DSP_MMU_24XX_PHYS, DSP_MMU_24XX_VIRT); + if (BETWEEN(p, DSP_MEM_2420_PHYS, DSP_MEM_2420_SIZE)) + return XLATE(p, DSP_MEM_2420_PHYS, DSP_MEM_2420_VIRT); + if (BETWEEN(p, DSP_IPI_2420_PHYS, DSP_IPI_2420_SIZE)) + return XLATE(p, DSP_IPI_2420_PHYS, DSP_IPI_2420_SIZE); + if (BETWEEN(p, DSP_MMU_2420_PHYS, DSP_MMU_2420_SIZE)) + return XLATE(p, DSP_MMU_2420_PHYS, DSP_MMU_2420_VIRT); } if (cpu_is_omap2430()) { if (BETWEEN(p, L4_WK_243X_PHYS, L4_WK_243X_SIZE)) diff --git a/arch/arm/plat-omap/iommu.c b/arch/arm/plat-omap/iommu.c index c0ff1e3..463d638 100644 --- a/arch/arm/plat-omap/iommu.c +++ b/arch/arm/plat-omap/iommu.c @@ -827,7 +827,7 @@ EXPORT_SYMBOL_GPL(iommu_get); **/ void iommu_put(struct iommu *obj) { - if (!obj && IS_ERR(obj)) + if (!obj || IS_ERR(obj)) return; mutex_lock(&obj->iommu_lock); diff --git a/arch/arm/plat-omap/mcbsp.c b/arch/arm/plat-omap/mcbsp.c index 2cc1cc3..f757672 100644 --- a/arch/arm/plat-omap/mcbsp.c +++ b/arch/arm/plat-omap/mcbsp.c @@ -436,7 +436,7 @@ int omap_mcbsp_request(unsigned int id) dev_err(mcbsp->dev, "Unable to request TX IRQ %d " "for McBSP%d\n", mcbsp->tx_irq, mcbsp->id); - return err; + goto error; } init_completion(&mcbsp->rx_irq_completion); @@ -446,12 +446,26 @@ int omap_mcbsp_request(unsigned int id) dev_err(mcbsp->dev, "Unable to request RX IRQ %d " "for McBSP%d\n", mcbsp->rx_irq, mcbsp->id); - free_irq(mcbsp->tx_irq, (void *)mcbsp); - return err; + goto tx_irq; } } return 0; +tx_irq: + free_irq(mcbsp->tx_irq, (void *)mcbsp); +error: + if (mcbsp->pdata && mcbsp->pdata->ops && mcbsp->pdata->ops->free) + mcbsp->pdata->ops->free(id); + + /* Do procedure specific to omap34xx arch, if applicable */ + omap34xx_mcbsp_free(mcbsp); + + clk_disable(mcbsp->fclk); + clk_disable(mcbsp->iclk); + + mcbsp->free = 1; + + return err; } EXPORT_SYMBOL(omap_mcbsp_request); diff --git a/arch/arm/plat-omap/omap_device.c b/arch/arm/plat-omap/omap_device.c index 1e5648d..2ed7201 100644 --- a/arch/arm/plat-omap/omap_device.c +++ b/arch/arm/plat-omap/omap_device.c @@ -89,16 +89,6 @@ #define USE_WAKEUP_LAT 0 #define IGNORE_WAKEUP_LAT 1 -/* XXX this should be moved into a separate file */ -#if defined(CONFIG_ARCH_OMAP2420) -# define OMAP_32KSYNCT_BASE 0x48004000 -#elif defined(CONFIG_ARCH_OMAP2430) -# define OMAP_32KSYNCT_BASE 0x49020000 -#elif defined(CONFIG_ARCH_OMAP3430) -# define OMAP_32KSYNCT_BASE 0x48320000 -#else -# error Unknown OMAP device -#endif /* Private functions */ diff --git a/arch/arm/plat-orion/pcie.c b/arch/arm/plat-orion/pcie.c index d41d41d..54c84a4 100644 --- a/arch/arm/plat-orion/pcie.c +++ b/arch/arm/plat-orion/pcie.c @@ -133,6 +133,12 @@ static void __init orion_pcie_setup_wins(void __iomem *base, } /* + * Round up 'size' to the nearest power of two. + */ + if ((size & (size - 1)) != 0) + size = 1 << fls(size); + + /* * Setup BAR[1] to all DRAM banks. */ writel(dram->cs[0].base, base + PCIE_BAR_LO_OFF(1)); diff --git a/arch/arm/plat-s3c/dev-nand.c b/arch/arm/plat-s3c/dev-nand.c index 84808cc..a52fb6c 100644 --- a/arch/arm/plat-s3c/dev-nand.c +++ b/arch/arm/plat-s3c/dev-nand.c @@ -58,8 +58,8 @@ static int __init s3c_nand_copy_set(struct s3c2410_nand_set *set) return -ENOMEM; } - size = sizeof(int) * set->nr_chips; - if (size) { + if (set->nr_map && set->nr_chips) { + size = sizeof(int) * set->nr_chips; ptr = kmemdup(set->nr_map, size, GFP_KERNEL); set->nr_map = ptr; diff --git a/arch/arm/plat-s3c64xx/s3c6400-clock.c b/arch/arm/plat-s3c64xx/s3c6400-clock.c index 6ffa21e..ffd56de 100644 --- a/arch/arm/plat-s3c64xx/s3c6400-clock.c +++ b/arch/arm/plat-s3c64xx/s3c6400-clock.c @@ -46,6 +46,7 @@ static struct clk clk_ext_xtal_mux = { #define clk_fin_epll clk_ext_xtal_mux #define clk_fout_mpll clk_mpll +#define clk_fout_epll clk_epll struct clk_sources { unsigned int nr_sources; @@ -88,11 +89,6 @@ static struct clksrc_clk clk_mout_apll = { .sources = &clk_src_apll, }; -static struct clk clk_fout_epll = { - .name = "fout_epll", - .id = -1, -}; - static struct clk *clk_src_epll_list[] = { [0] = &clk_fin_epll, [1] = &clk_fout_epll, @@ -715,7 +711,6 @@ static struct clk *clks[] __initdata = { &clk_iis_cd1, &clk_pcm_cd, &clk_mout_epll.clk, - &clk_fout_epll, &clk_mout_mpll.clk, &clk_dout_mpll, &clk_mmc0.clk, @@ -760,7 +755,4 @@ void __init s3c6400_register_clocks(unsigned armclk_divlimit) clkp->name, ret); } } - - clk_mpll.parent = &clk_mout_mpll.clk; - clk_epll.parent = &clk_mout_epll.clk; } diff --git a/arch/arm/tools/mach-types b/arch/arm/tools/mach-types index c3a74ce..5a79fc6 100644 --- a/arch/arm/tools/mach-types +++ b/arch/arm/tools/mach-types @@ -12,7 +12,7 @@ # # http://www.arm.linux.org.uk/developer/machines/?action=new # -# Last update: Wed Dec 16 20:06:34 2009 +# Last update: Thu Jan 28 22:15:54 2010 # # machine_is_xxx CONFIG_xxxx MACH_TYPE_xxx number # @@ -2536,6 +2536,7 @@ davinci_dm6467tevm MACH_DAVINCI_DM6467TEVM DAVINCI_DM6467TEVM 2548 c3ax03 MACH_C3AX03 C3AX03 2549 mxt_td60 MACH_MXT_TD60 MXT_TD60 2550 esyx MACH_ESYX ESYX 2551 +dove_db2 MACH_DOVE_DB2 DOVE_DB2 2552 bulldog MACH_BULLDOG BULLDOG 2553 derell_me2000 MACH_DERELL_ME2000 DERELL_ME2000 2554 bcmring_base MACH_BCMRING_BASE BCMRING_BASE 2555 @@ -2555,6 +2556,7 @@ iseo MACH_ISEO ISEO 2568 cezanne MACH_CEZANNE CEZANNE 2569 lucca MACH_LUCCA LUCCA 2570 supersmart MACH_SUPERSMART SUPERSMART 2571 +arm11_board MACH_CS_MISANO CS_MISANO 2572 magnolia2 MACH_MAGNOLIA2 MAGNOLIA2 2573 emxx MACH_EMXX EMXX 2574 outlaw MACH_OUTLAW OUTLAW 2575 @@ -2578,3 +2580,59 @@ glacier MACH_GLACIER GLACIER 2592 phrazer_bulldog MACH_PHRAZER_BULLDOG PHRAZER_BULLDOG 2593 omap3_bulldog MACH_OMAP3_BULLDOG OMAP3_BULLDOG 2594 pca101 MACH_PCA101 PCA101 2595 +buzzc MACH_BUZZC BUZZC 2596 +sasie2 MACH_SASIE2 SASIE2 2597 +davinci_cio MACH_DAVINCI_CIO DAVINCI_CIO 2598 +smartmeter_dl MACH_SMARTMETER_DL SMARTMETER_DL 2599 +wzl6410 MACH_WZL6410 WZL6410 2600 +wzl6410m MACH_WZL6410M WZL6410M 2601 +wzl6410f MACH_WZL6410F WZL6410F 2602 +wzl6410i MACH_WZL6410I WZL6410I 2603 +spacecom1 MACH_SPACECOM1 SPACECOM1 2604 +pingu920 MACH_PINGU920 PINGU920 2605 +bravoc MACH_BRAVOC BRAVOC 2606 +cybo2440 MACH_CYBO2440 CYBO2440 2607 +vdssw MACH_VDSSW VDSSW 2608 +romulus MACH_ROMULUS ROMULUS 2609 +omap_magic MACH_OMAP_MAGIC OMAP_MAGIC 2610 +eltd100 MACH_ELTD100 ELTD100 2611 +capc7117 MACH_CAPC7117 CAPC7117 2612 +swan MACH_SWAN SWAN 2613 +veu MACH_VEU VEU 2614 +rm2 MACH_RM2 RM2 2615 +tt2100 MACH_TT2100 TT2100 2616 +venice MACH_VENICE VENICE 2617 +pc7323 MACH_PC7323 PC7323 2618 +masp MACH_MASP MASP 2619 +fujitsu_tvstbsoc0 MACH_FUJITSU_TVSTBSOC FUJITSU_TVSTBSOC 2620 +fujitsu_tvstbsoc1 MACH_FUJITSU_TVSTBSOC1 FUJITSU_TVSTBSOC1 2621 +lexikon MACH_LEXIKON LEXIKON 2622 +mini2440v2 MACH_MINI2440V2 MINI2440V2 2623 +icontrol MACH_ICONTROL ICONTROL 2624 +sheevad MACH_SHEEVAD SHEEVAD 2625 +qsd8x50a_st1_1 MACH_QSD8X50A_ST1_1 QSD8X50A_ST1_1 2626 +qsd8x50a_st1_5 MACH_QSD8X50A_ST1_5 QSD8X50A_ST1_5 2627 +bee MACH_BEE BEE 2628 +mx23evk MACH_MX23EVK MX23EVK 2629 +ap4evb MACH_AP4EVB AP4EVB 2630 +stockholm MACH_STOCKHOLM STOCKHOLM 2631 +lpc_h3131 MACH_LPC_H3131 LPC_H3131 2632 +stingray MACH_STINGRAY STINGRAY 2633 +kraken MACH_KRAKEN KRAKEN 2634 +gw2388 MACH_GW2388 GW2388 2635 +jadecpu MACH_JADECPU JADECPU 2636 +carlisle MACH_CARLISLE CARLISLE 2637 +lux_sf9 MACH_LUX_SFT9 LUX_SFT9 2638 +nemid_tb MACH_NEMID_TB NEMID_TB 2639 +terrier MACH_TERRIER TERRIER 2640 +turbot MACH_TURBOT TURBOT 2641 +sanddab MACH_SANDDAB SANDDAB 2642 +mx35_cicada MACH_MX35_CICADA MX35_CICADA 2643 +ghi2703d MACH_GHI2703D GHI2703D 2644 +lux_sfx9 MACH_LUX_SFX9 LUX_SFX9 2645 +lux_sf9g MACH_LUX_SF9G LUX_SF9G 2646 +lux_edk9 MACH_LUX_EDK9 LUX_EDK9 2647 +hw90240 MACH_HW90240 HW90240 2648 +dm365_leopard MACH_DM365_LEOPARD DM365_LEOPARD 2649 +mityomapl138 MACH_MITYOMAPL138 MITYOMAPL138 2650 +scat110 MACH_SCAT110 SCAT110 2651 diff --git a/arch/arm/vfp/vfpmodule.c b/arch/arm/vfp/vfpmodule.c index f60a540..a63c4be 100644 --- a/arch/arm/vfp/vfpmodule.c +++ b/arch/arm/vfp/vfpmodule.c @@ -197,10 +197,13 @@ static void vfp_raise_exceptions(u32 exceptions, u32 inst, u32 fpscr, struct pt_ } /* - * Update the FPSCR with the additional exception flags. + * If any of the status flags are set, update the FPSCR. * Comparison instructions always return at least one of * these flags set. */ + if (exceptions & (FPSCR_N|FPSCR_Z|FPSCR_C|FPSCR_V)) + fpscr &= ~(FPSCR_N|FPSCR_Z|FPSCR_C|FPSCR_V); + fpscr |= exceptions; fmxr(FPSCR, fpscr); |
