diff options
Diffstat (limited to 'arch/arm/plat-samsung')
| -rw-r--r-- | arch/arm/plat-samsung/Makefile | 2 | ||||
| -rw-r--r-- | arch/arm/plat-samsung/include/plat/cpu.h | 6 | ||||
| -rw-r--r-- | arch/arm/plat-samsung/include/plat/pm-common.h | 110 | ||||
| -rw-r--r-- | arch/arm/plat-samsung/include/plat/pm.h | 80 | ||||
| -rw-r--r-- | arch/arm/plat-samsung/pm-check.c | 2 | ||||
| -rw-r--r-- | arch/arm/plat-samsung/pm-common.c | 75 | ||||
| -rw-r--r-- | arch/arm/plat-samsung/pm-debug.c | 97 | ||||
| -rw-r--r-- | arch/arm/plat-samsung/pm.c | 144 | ||||
| -rw-r--r-- | arch/arm/plat-samsung/s5p-sleep.S | 43 |
9 files changed, 292 insertions, 267 deletions
diff --git a/arch/arm/plat-samsung/Makefile b/arch/arm/plat-samsung/Makefile index 9267d29..25c826e 100644 --- a/arch/arm/plat-samsung/Makefile +++ b/arch/arm/plat-samsung/Makefile @@ -47,9 +47,11 @@ obj-$(CONFIG_SAMSUNG_DMADEV) += dma-ops.o # PM support +obj-$(CONFIG_PM_SLEEP) += pm-common.o obj-$(CONFIG_SAMSUNG_PM) += pm.o obj-$(CONFIG_SAMSUNG_PM_GPIO) += pm-gpio.o obj-$(CONFIG_SAMSUNG_PM_CHECK) += pm-check.o +obj-$(CONFIG_SAMSUNG_PM_DEBUG) += pm-debug.o obj-$(CONFIG_SAMSUNG_WAKEMASK) += wakeup-mask.o obj-$(CONFIG_SAMSUNG_WDT_RESET) += watchdog-reset.o diff --git a/arch/arm/plat-samsung/include/plat/cpu.h b/arch/arm/plat-samsung/include/plat/cpu.h index 31164b3..d762533 100644 --- a/arch/arm/plat-samsung/include/plat/cpu.h +++ b/arch/arm/plat-samsung/include/plat/cpu.h @@ -20,6 +20,9 @@ extern unsigned long samsung_cpu_id; +#define S3C2410_CPU_ID 0x32410000 +#define S3C2410_CPU_MASK 0xFFFFFFFF + #define S3C24XX_CPU_ID 0x32400000 #define S3C24XX_CPU_MASK 0xFFF00000 @@ -56,6 +59,7 @@ static inline int is_samsung_##name(void) \ return ((samsung_cpu_id & mask) == (id & mask)); \ } +IS_SAMSUNG_CPU(s3c2410, S3C2410_CPU_ID, S3C2410_CPU_MASK) IS_SAMSUNG_CPU(s3c24xx, S3C24XX_CPU_ID, S3C24XX_CPU_MASK) IS_SAMSUNG_CPU(s3c2412, S3C2412_CPU_ID, S3C2412_CPU_MASK) IS_SAMSUNG_CPU(s3c6400, S3C6400_CPU_ID, S3C64XX_CPU_MASK) @@ -76,8 +80,10 @@ IS_SAMSUNG_CPU(exynos5440, EXYNOS5440_SOC_ID, EXYNOS5_SOC_MASK) defined(CONFIG_CPU_S3C2442) || defined(CONFIG_CPU_S3C244X) || \ defined(CONFIG_CPU_S3C2443) # define soc_is_s3c24xx() is_samsung_s3c24xx() +# define soc_is_s3c2410() is_samsung_s3c2410() #else # define soc_is_s3c24xx() 0 +# define soc_is_s3c2410() 0 #endif #if defined(CONFIG_CPU_S3C2412) diff --git a/arch/arm/plat-samsung/include/plat/pm-common.h b/arch/arm/plat-samsung/include/plat/pm-common.h new file mode 100644 index 0000000..8705f9e --- /dev/null +++ b/arch/arm/plat-samsung/include/plat/pm-common.h @@ -0,0 +1,110 @@ +/* + * Copyright (C) 2013 Samsung Electronics Co., Ltd. + * Tomasz Figa <t.figa@samsung.com> + * Copyright (c) 2004 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * Written by Ben Dooks, <ben@simtec.co.uk> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#ifndef __PLAT_SAMSUNG_PM_COMMON_H +#define __PLAT_SAMSUNG_PM_COMMON_H __FILE__ + +#include <linux/irq.h> + +/* sleep save info */ + +/** + * struct sleep_save - save information for shared peripherals. + * @reg: Pointer to the register to save. + * @val: Holder for the value saved from reg. + * + * This describes a list of registers which is used by the pm core and + * other subsystem to save and restore register values over suspend. + */ +struct sleep_save { + void __iomem *reg; + unsigned long val; +}; + +#define SAVE_ITEM(x) \ + { .reg = (x) } + +/* helper functions to save/restore lists of registers. */ + +extern void s3c_pm_do_save(struct sleep_save *ptr, int count); +extern void s3c_pm_do_restore(const struct sleep_save *ptr, int count); +extern void s3c_pm_do_restore_core(const struct sleep_save *ptr, int count); + +/* PM debug functions */ + +/** + * struct pm_uart_save - save block for core UART + * @ulcon: Save value for S3C2410_ULCON + * @ucon: Save value for S3C2410_UCON + * @ufcon: Save value for S3C2410_UFCON + * @umcon: Save value for S3C2410_UMCON + * @ubrdiv: Save value for S3C2410_UBRDIV + * + * Save block for UART registers to be held over sleep and restored if they + * are needed (say by debug). +*/ +struct pm_uart_save { + u32 ulcon; + u32 ucon; + u32 ufcon; + u32 umcon; + u32 ubrdiv; + u32 udivslot; +}; + +#ifdef CONFIG_SAMSUNG_PM_DEBUG +/** + * s3c_pm_dbg() - low level debug function for use in suspend/resume. + * @msg: The message to print. + * + * This function is used mainly to debug the resume process before the system + * can rely on printk/console output. It uses the low-level debugging output + * routine printascii() to do its work. + */ +extern void s3c_pm_dbg(const char *msg, ...); + +/** + * s3c_pm_debug_init() - suspend/resume low level debug initialization. + * @base: Virtual base of UART to use for suspend/resume debugging. + * + * This function needs to be called before S3C_PMDBG() can be used, to set up + * UART port base address and configuration. + */ +extern void s3c_pm_debug_init(void); + +#define S3C_PMDBG(fmt...) s3c_pm_dbg(fmt) + +extern void s3c_pm_save_uarts(void); +extern void s3c_pm_restore_uarts(void); +#else +#define S3C_PMDBG(fmt...) pr_debug(fmt) +#define s3c_pm_debug_init() do { } while (0) + +static inline void s3c_pm_save_uarts(void) { } +static inline void s3c_pm_restore_uarts(void) { } +#endif + +/* suspend memory checking */ + +#ifdef CONFIG_SAMSUNG_PM_CHECK +extern void s3c_pm_check_prepare(void); +extern void s3c_pm_check_restore(void); +extern void s3c_pm_check_cleanup(void); +extern void s3c_pm_check_store(void); +#else +#define s3c_pm_check_prepare() do { } while (0) +#define s3c_pm_check_restore() do { } while (0) +#define s3c_pm_check_cleanup() do { } while (0) +#define s3c_pm_check_store() do { } while (0) +#endif + +#endif diff --git a/arch/arm/plat-samsung/include/plat/pm.h b/arch/arm/plat-samsung/include/plat/pm.h index ff6063f..e17d871 100644 --- a/arch/arm/plat-samsung/include/plat/pm.h +++ b/arch/arm/plat-samsung/include/plat/pm.h @@ -15,7 +15,7 @@ * management */ -#include <linux/irq.h> +#include <plat/pm-common.h> struct device; @@ -54,56 +54,10 @@ extern int (*pm_cpu_sleep)(unsigned long); extern unsigned long s3c_pm_flags; -extern unsigned char pm_uart_udivslot; /* true to save UART UDIVSLOT */ - /* from sleep.S */ extern int s3c2410_cpu_suspend(unsigned long); -/* sleep save info */ - -/** - * struct sleep_save - save information for shared peripherals. - * @reg: Pointer to the register to save. - * @val: Holder for the value saved from reg. - * - * This describes a list of registers which is used by the pm core and - * other subsystem to save and restore register values over suspend. - */ -struct sleep_save { - void __iomem *reg; - unsigned long val; -}; - -#define SAVE_ITEM(x) \ - { .reg = (x) } - -/** - * struct pm_uart_save - save block for core UART - * @ulcon: Save value for S3C2410_ULCON - * @ucon: Save value for S3C2410_UCON - * @ufcon: Save value for S3C2410_UFCON - * @umcon: Save value for S3C2410_UMCON - * @ubrdiv: Save value for S3C2410_UBRDIV - * - * Save block for UART registers to be held over sleep and restored if they - * are needed (say by debug). -*/ -struct pm_uart_save { - u32 ulcon; - u32 ucon; - u32 ufcon; - u32 umcon; - u32 ubrdiv; - u32 udivslot; -}; - -/* helper functions to save/restore lists of registers. */ - -extern void s3c_pm_do_save(struct sleep_save *ptr, int count); -extern void s3c_pm_do_restore(const struct sleep_save *ptr, int count); -extern void s3c_pm_do_restore_core(const struct sleep_save *ptr, int count); - #ifdef CONFIG_SAMSUNG_PM extern int s3c_irq_wake(struct irq_data *data, unsigned int state); extern int s3c_irqext_wake(struct irq_data *data, unsigned int state); @@ -114,24 +68,6 @@ extern void s3c_cpu_resume(void); #define s3c_cpu_resume NULL #endif -/* PM debug functions */ - -#ifdef CONFIG_SAMSUNG_PM_DEBUG -/** - * s3c_pm_dbg() - low level debug function for use in suspend/resume. - * @msg: The message to print. - * - * This function is used mainly to debug the resume process before the system - * can rely on printk/console output. It uses the low-level debugging output - * routine printascii() to do its work. - */ -extern void s3c_pm_dbg(const char *msg, ...); - -#define S3C_PMDBG(fmt...) s3c_pm_dbg(fmt) -#else -#define S3C_PMDBG(fmt...) printk(KERN_DEBUG fmt) -#endif - #ifdef CONFIG_S3C_PM_DEBUG_LED_SMDK /** * s3c_pm_debug_smdkled() - Debug PM suspend/resume via SMDK Board LEDs @@ -144,20 +80,6 @@ extern void s3c_pm_debug_smdkled(u32 set, u32 clear); static inline void s3c_pm_debug_smdkled(u32 set, u32 clear) { } #endif /* CONFIG_S3C_PM_DEBUG_LED_SMDK */ -/* suspend memory checking */ - -#ifdef CONFIG_SAMSUNG_PM_CHECK -extern void s3c_pm_check_prepare(void); -extern void s3c_pm_check_restore(void); -extern void s3c_pm_check_cleanup(void); -extern void s3c_pm_check_store(void); -#else -#define s3c_pm_check_prepare() do { } while(0) -#define s3c_pm_check_restore() do { } while(0) -#define s3c_pm_check_cleanup() do { } while(0) -#define s3c_pm_check_store() do { } while(0) -#endif - /** * s3c_pm_configure_extint() - ensure pins are correctly set for IRQ * diff --git a/arch/arm/plat-samsung/pm-check.c b/arch/arm/plat-samsung/pm-check.c index 3cbd626..04aff2c 100644 --- a/arch/arm/plat-samsung/pm-check.c +++ b/arch/arm/plat-samsung/pm-check.c @@ -19,7 +19,7 @@ #include <linux/ioport.h> #include <linux/slab.h> -#include <plat/pm.h> +#include <plat/pm-common.h> #if CONFIG_SAMSUNG_PM_CHECK_CHUNKSIZE < 1 #error CONFIG_SAMSUNG_PM_CHECK_CHUNKSIZE must be a positive non-zero value diff --git a/arch/arm/plat-samsung/pm-common.c b/arch/arm/plat-samsung/pm-common.c new file mode 100644 index 0000000..515cd53 --- /dev/null +++ b/arch/arm/plat-samsung/pm-common.c @@ -0,0 +1,75 @@ +/* + * Copyright (C) 2013 Samsung Electronics Co., Ltd. + * Tomasz Figa <t.figa@samsung.com> + * Copyright (C) 2008 Openmoko, Inc. + * Copyright (C) 2004-2008 Simtec Electronics + * Ben Dooks <ben@simtec.co.uk> + * http://armlinux.simtec.co.uk/ + * + * Samsung common power management helper functions. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include <linux/io.h> +#include <linux/kernel.h> + +#include <plat/pm-common.h> + +/* helper functions to save and restore register state */ + +/** + * s3c_pm_do_save() - save a set of registers for restoration on resume. + * @ptr: Pointer to an array of registers. + * @count: Size of the ptr array. + * + * Run through the list of registers given, saving their contents in the + * array for later restoration when we wakeup. + */ +void s3c_pm_do_save(struct sleep_save *ptr, int count) +{ + for (; count > 0; count--, ptr++) { + ptr->val = __raw_readl(ptr->reg); + S3C_PMDBG("saved %p value %08lx\n", ptr->reg, ptr->val); + } +} + +/** + * s3c_pm_do_restore() - restore register values from the save list. + * @ptr: Pointer to an array of registers. + * @count: Size of the ptr array. + * + * Restore the register values saved from s3c_pm_do_save(). + * + * Note, we do not use S3C_PMDBG() in here, as the system may not have + * restore the UARTs state yet +*/ + +void s3c_pm_do_restore(const struct sleep_save *ptr, int count) +{ + for (; count > 0; count--, ptr++) { + pr_debug("restore %p (restore %08lx, was %08x)\n", + ptr->reg, ptr->val, __raw_readl(ptr->reg)); + + __raw_writel(ptr->val, ptr->reg); + } +} + +/** + * s3c_pm_do_restore_core() - early restore register values from save list. + * + * This is similar to s3c_pm_do_restore() except we try and minimise the + * side effects of the function in case registers that hardware might need + * to work has been restored. + * + * WARNING: Do not put any debug in here that may effect memory or use + * peripherals, as things may be changing! +*/ + +void s3c_pm_do_restore_core(const struct sleep_save *ptr, int count) +{ + for (; count > 0; count--, ptr++) + __raw_writel(ptr->val, ptr->reg); +} diff --git a/arch/arm/plat-samsung/pm-debug.c b/arch/arm/plat-samsung/pm-debug.c new file mode 100644 index 0000000..8f19f66 --- /dev/null +++ b/arch/arm/plat-samsung/pm-debug.c @@ -0,0 +1,97 @@ +/* + * Copyright (C) 2013 Samsung Electronics Co., Ltd. + * Tomasz Figa <t.figa@samsung.com> + * Copyright (C) 2008 Openmoko, Inc. + * Copyright (C) 2004-2008 Simtec Electronics + * Ben Dooks <ben@simtec.co.uk> + * http://armlinux.simtec.co.uk/ + * + * Samsung common power management (suspend to RAM) debug support + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/serial_core.h> +#include <linux/io.h> + +#include <asm/mach/map.h> + +#include <plat/cpu.h> +#include <plat/pm-common.h> + +#ifdef CONFIG_SAMSUNG_ATAGS +#include <mach/pm-core.h> +#else +static inline void s3c_pm_debug_init_uart(void) {} +static inline void s3c_pm_arch_update_uart(void __iomem *regs, + struct pm_uart_save *save) {} +#endif + +static struct pm_uart_save uart_save; + +extern void printascii(const char *); + +void s3c_pm_dbg(const char *fmt, ...) +{ + va_list va; + char buff[256]; + + va_start(va, fmt); + vsnprintf(buff, sizeof(buff), fmt, va); + va_end(va); + + printascii(buff); +} + +void s3c_pm_debug_init(void) +{ + /* restart uart clocks so we can use them to output */ + s3c_pm_debug_init_uart(); +} + +static inline void __iomem *s3c_pm_uart_base(void) +{ + unsigned long paddr; + unsigned long vaddr; + + debug_ll_addr(&paddr, &vaddr); + + return (void __iomem *)vaddr; +} + +void s3c_pm_save_uarts(void) +{ + void __iomem *regs = s3c_pm_uart_base(); + struct pm_uart_save *save = &uart_save; + + save->ulcon = __raw_readl(regs + S3C2410_ULCON); + save->ucon = __raw_readl(regs + S3C2410_UCON); + save->ufcon = __raw_readl(regs + S3C2410_UFCON); + save->umcon = __raw_readl(regs + S3C2410_UMCON); + save->ubrdiv = __raw_readl(regs + S3C2410_UBRDIV); + + if (!soc_is_s3c2410()) + save->udivslot = __raw_readl(regs + S3C2443_DIVSLOT); + + S3C_PMDBG("UART[%p]: ULCON=%04x, UCON=%04x, UFCON=%04x, UBRDIV=%04x\n", + regs, save->ulcon, save->ucon, save->ufcon, save->ubrdiv); +} + +void s3c_pm_restore_uarts(void) +{ + void __iomem *regs = s3c_pm_uart_base(); + struct pm_uart_save *save = &uart_save; + + s3c_pm_arch_update_uart(regs, save); + + __raw_writel(save->ulcon, regs + S3C2410_ULCON); + __raw_writel(save->ucon, regs + S3C2410_UCON); + __raw_writel(save->ufcon, regs + S3C2410_UFCON); + __raw_writel(save->umcon, regs + S3C2410_UMCON); + __raw_writel(save->ubrdiv, regs + S3C2410_UBRDIV); + + if (!soc_is_s3c2410()) + __raw_writel(save->udivslot, regs + S3C2443_DIVSLOT); +} diff --git a/arch/arm/plat-samsung/pm.c b/arch/arm/plat-samsung/pm.c index d438e77..f8c0f97 100644 --- a/arch/arm/plat-samsung/pm.c +++ b/arch/arm/plat-samsung/pm.c @@ -17,7 +17,6 @@ #include <linux/errno.h> #include <linux/delay.h> #include <linux/of.h> -#include <linux/serial_core.h> #include <linux/serial_s3c.h> #include <linux/io.h> @@ -42,93 +41,6 @@ unsigned long s3c_pm_flags; -/* Debug code: - * - * This code supports debug output to the low level UARTs for use on - * resume before the console layer is available. -*/ - -#ifdef CONFIG_SAMSUNG_PM_DEBUG -extern void printascii(const char *); - -void s3c_pm_dbg(const char *fmt, ...) -{ - va_list va; - char buff[256]; - - va_start(va, fmt); - vsnprintf(buff, sizeof(buff), fmt, va); - va_end(va); - - printascii(buff); -} - -static inline void s3c_pm_debug_init(void) -{ - /* restart uart clocks so we can use them to output */ - s3c_pm_debug_init_uart(); -} - -#else -#define s3c_pm_debug_init() do { } while(0) - -#endif /* CONFIG_SAMSUNG_PM_DEBUG */ - -/* Save the UART configurations if we are configured for debug. */ - -unsigned char pm_uart_udivslot; - -#ifdef CONFIG_SAMSUNG_PM_DEBUG - -static struct pm_uart_save uart_save; - -static void s3c_pm_save_uart(unsigned int uart, struct pm_uart_save *save) -{ - void __iomem *regs = S3C_VA_UARTx(uart); - - save->ulcon = __raw_readl(regs + S3C2410_ULCON); - save->ucon = __raw_readl(regs + S3C2410_UCON); - save->ufcon = __raw_readl(regs + S3C2410_UFCON); - save->umcon = __raw_readl(regs + S3C2410_UMCON); - save->ubrdiv = __raw_readl(regs + S3C2410_UBRDIV); - - if (pm_uart_udivslot) - save->udivslot = __raw_readl(regs + S3C2443_DIVSLOT); - - S3C_PMDBG("UART[%d]: ULCON=%04x, UCON=%04x, UFCON=%04x, UBRDIV=%04x\n", - uart, save->ulcon, save->ucon, save->ufcon, save->ubrdiv); -} - -static void s3c_pm_save_uarts(void) -{ - s3c_pm_save_uart(CONFIG_DEBUG_S3C_UART, &uart_save); -} - -static void s3c_pm_restore_uart(unsigned int uart, struct pm_uart_save *save) -{ - void __iomem *regs = S3C_VA_UARTx(uart); - - s3c_pm_arch_update_uart(regs, save); - - __raw_writel(save->ulcon, regs + S3C2410_ULCON); - __raw_writel(save->ucon, regs + S3C2410_UCON); - __raw_writel(save->ufcon, regs + S3C2410_UFCON); - __raw_writel(save->umcon, regs + S3C2410_UMCON); - __raw_writel(save->ubrdiv, regs + S3C2410_UBRDIV); - - if (pm_uart_udivslot) - __raw_writel(save->udivslot, regs + S3C2443_DIVSLOT); -} - -static void s3c_pm_restore_uarts(void) -{ - s3c_pm_restore_uart(CONFIG_DEBUG_S3C_UART, &uart_save); -} -#else -static void s3c_pm_save_uarts(void) { } -static void s3c_pm_restore_uarts(void) { } -#endif - /* The IRQ ext-int code goes here, it is too small to currently bother * with its own file. */ @@ -153,62 +65,6 @@ int s3c_irqext_wake(struct irq_data *data, unsigned int state) return 0; } -/* helper functions to save and restore register state */ - -/** - * s3c_pm_do_save() - save a set of registers for restoration on resume. - * @ptr: Pointer to an array of registers. - * @count: Size of the ptr array. - * - * Run through the list of registers given, saving their contents in the - * array for later restoration when we wakeup. - */ -void s3c_pm_do_save(struct sleep_save *ptr, int count) -{ - for (; count > 0; count--, ptr++) { - ptr->val = __raw_readl(ptr->reg); - S3C_PMDBG("saved %p value %08lx\n", ptr->reg, ptr->val); - } -} - -/** - * s3c_pm_do_restore() - restore register values from the save list. - * @ptr: Pointer to an array of registers. - * @count: Size of the ptr array. - * - * Restore the register values saved from s3c_pm_do_save(). - * - * Note, we do not use S3C_PMDBG() in here, as the system may not have - * restore the UARTs state yet -*/ - -void s3c_pm_do_restore(const struct sleep_save *ptr, int count) -{ - for (; count > 0; count--, ptr++) { - printk(KERN_DEBUG "restore %p (restore %08lx, was %08x)\n", - ptr->reg, ptr->val, __raw_readl(ptr->reg)); - - __raw_writel(ptr->val, ptr->reg); - } -} - -/** - * s3c_pm_do_restore_core() - early restore register values from save list. - * - * This is similar to s3c_pm_do_restore() except we try and minimise the - * side effects of the function in case registers that hardware might need - * to work has been restored. - * - * WARNING: Do not put any debug in here that may effect memory or use - * peripherals, as things may be changing! -*/ - -void s3c_pm_do_restore_core(const struct sleep_save *ptr, int count) -{ - for (; count > 0; count--, ptr++) - __raw_writel(ptr->val, ptr->reg); -} - /* s3c2410_pm_show_resume_irqs * * print any IRQs asserted at resume time (ie, we woke from) diff --git a/arch/arm/plat-samsung/s5p-sleep.S b/arch/arm/plat-samsung/s5p-sleep.S index a030e73..c500165 100644 --- a/arch/arm/plat-samsung/s5p-sleep.S +++ b/arch/arm/plat-samsung/s5p-sleep.S @@ -23,18 +23,7 @@ #include <linux/linkage.h> #include <asm/asm-offsets.h> -#include <asm/hardware/cache-l2x0.h> -#define CPU_MASK 0xff0ffff0 -#define CPU_CORTEX_A9 0x410fc090 - -/* - * The following code is located into the .data section. This is to - * allow l2x0_regs_phys to be accessed with a relative load while we - * can't rely on any MMU translation. We could have put l2x0_regs_phys - * in the .text section as well, but some setups might insist on it to - * be truly read-only. (Reference from: arch/arm/kernel/sleep.S) - */ .data .align @@ -53,37 +42,5 @@ */ ENTRY(s3c_cpu_resume) -#ifdef CONFIG_CACHE_L2X0 - mrc p15, 0, r0, c0, c0, 0 - ldr r1, =CPU_MASK - and r0, r0, r1 - ldr r1, =CPU_CORTEX_A9 - cmp r0, r1 - bne resume_l2on - adr r0, l2x0_regs_phys - ldr r0, [r0] - ldr r1, [r0, #L2X0_R_PHY_BASE] - ldr r2, [r1, #L2X0_CTRL] - tst r2, #0x1 - bne resume_l2on - ldr r2, [r0, #L2X0_R_AUX_CTRL] - str r2, [r1, #L2X0_AUX_CTRL] - ldr r2, [r0, #L2X0_R_TAG_LATENCY] - str r2, [r1, #L2X0_TAG_LATENCY_CTRL] - ldr r2, [r0, #L2X0_R_DATA_LATENCY] - str r2, [r1, #L2X0_DATA_LATENCY_CTRL] - ldr r2, [r0, #L2X0_R_PREFETCH_CTRL] - str r2, [r1, #L2X0_PREFETCH_CTRL] - ldr r2, [r0, #L2X0_R_PWR_CTRL] - str r2, [r1, #L2X0_POWER_CTRL] - mov r2, #1 - str r2, [r1, #L2X0_CTRL] -resume_l2on: -#endif b cpu_resume ENDPROC(s3c_cpu_resume) -#ifdef CONFIG_CACHE_L2X0 - .globl l2x0_regs_phys -l2x0_regs_phys: - .long 0 -#endif |
