diff options
Diffstat (limited to 'arch/arm/plat-omap')
| -rw-r--r-- | arch/arm/plat-omap/Makefile | 2 | ||||
| -rw-r--r-- | arch/arm/plat-omap/common.c | 275 | ||||
| -rw-r--r-- | arch/arm/plat-omap/counter_32k.c | 183 | ||||
| -rw-r--r-- | arch/arm/plat-omap/devices.c | 1 | ||||
| -rw-r--r-- | arch/arm/plat-omap/sram.c | 3 |
5 files changed, 184 insertions, 280 deletions
diff --git a/arch/arm/plat-omap/Makefile b/arch/arm/plat-omap/Makefile index 2a15191..a4a1285 100644 --- a/arch/arm/plat-omap/Makefile +++ b/arch/arm/plat-omap/Makefile @@ -4,7 +4,7 @@ # Common support obj-y := common.o sram.o clock.o devices.o dma.o mux.o gpio.o \ - usb.o fb.o io.o + usb.o fb.o io.o counter_32k.o obj-m := obj-n := obj- := diff --git a/arch/arm/plat-omap/common.c b/arch/arm/plat-omap/common.c index cbaf14b..221a675 100644 --- a/arch/arm/plat-omap/common.c +++ b/arch/arm/plat-omap/common.c @@ -11,38 +11,15 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ -#include <linux/module.h> #include <linux/kernel.h> #include <linux/init.h> -#include <linux/delay.h> -#include <linux/console.h> -#include <linux/serial.h> -#include <linux/tty.h> -#include <linux/serial_8250.h> -#include <linux/serial_reg.h> -#include <linux/clk.h> #include <linux/io.h> #include <linux/omapfb.h> -#include <mach/hardware.h> -#include <asm/system.h> -#include <asm/pgtable.h> -#include <asm/mach/map.h> -#include <asm/setup.h> - #include <plat/common.h> #include <plat/board.h> -#include <plat/control.h> -#include <plat/mux.h> -#include <plat/fpga.h> -#include <plat/serial.h> #include <plat/vram.h> -#include <plat/clock.h> - -#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) -# include "../mach-omap2/sdrc.h" -#endif #define NO_LENGTH_CHECK 0xffffffff @@ -88,255 +65,3 @@ void __init omap_reserve(void) omapfb_reserve_sdram_memblock(); omap_vram_reserve_sdram_memblock(); } - -/* - * 32KHz clocksource ... always available, on pretty most chips except - * OMAP 730 and 1510. Other timers could be used as clocksources, with - * higher resolution in free-running counter modes (e.g. 12 MHz xtal), - * but systems won't necessarily want to spend resources that way. - */ - -#define OMAP16XX_TIMER_32K_SYNCHRONIZED 0xfffbc410 - -#if !(defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP15XX)) - -#include <linux/clocksource.h> - -/* - * offset_32k holds the init time counter value. It is then subtracted - * from every counter read to achieve a counter that counts time from the - * kernel boot (needed for sched_clock()). - */ -static u32 offset_32k __read_mostly; - -#ifdef CONFIG_ARCH_OMAP16XX -static cycle_t omap16xx_32k_read(struct clocksource *cs) -{ - return omap_readl(OMAP16XX_TIMER_32K_SYNCHRONIZED) - offset_32k; -} -#else -#define omap16xx_32k_read NULL -#endif - -#ifdef CONFIG_ARCH_OMAP2420 -static cycle_t omap2420_32k_read(struct clocksource *cs) -{ - return omap_readl(OMAP2420_32KSYNCT_BASE + 0x10) - offset_32k; -} -#else -#define omap2420_32k_read NULL -#endif - -#ifdef CONFIG_ARCH_OMAP2430 -static cycle_t omap2430_32k_read(struct clocksource *cs) -{ - return omap_readl(OMAP2430_32KSYNCT_BASE + 0x10) - offset_32k; -} -#else -#define omap2430_32k_read NULL -#endif - -#ifdef CONFIG_ARCH_OMAP3 -static cycle_t omap34xx_32k_read(struct clocksource *cs) -{ - return omap_readl(OMAP3430_32KSYNCT_BASE + 0x10) - offset_32k; -} -#else -#define omap34xx_32k_read NULL -#endif - -#ifdef CONFIG_ARCH_OMAP4 -static cycle_t omap44xx_32k_read(struct clocksource *cs) -{ - return omap_readl(OMAP4430_32KSYNCT_BASE + 0x10) - offset_32k; -} -#else -#define omap44xx_32k_read NULL -#endif - -/* - * Kernel assumes that sched_clock can be called early but may not have - * things ready yet. - */ -static cycle_t omap_32k_read_dummy(struct clocksource *cs) -{ - return 0; -} - -static struct clocksource clocksource_32k = { - .name = "32k_counter", - .rating = 250, - .read = omap_32k_read_dummy, - .mask = CLOCKSOURCE_MASK(32), - .shift = 10, - .flags = CLOCK_SOURCE_IS_CONTINUOUS, -}; - -/* - * Returns current time from boot in nsecs. It's OK for this to wrap - * around for now, as it's just a relative time stamp. - */ -unsigned long long sched_clock(void) -{ - return clocksource_cyc2ns(clocksource_32k.read(&clocksource_32k), - clocksource_32k.mult, clocksource_32k.shift); -} - -/** - * read_persistent_clock - Return time from a persistent clock. - * - * Reads the time from a source which isn't disabled during PM, the - * 32k sync timer. Convert the cycles elapsed since last read into - * nsecs and adds to a monotonically increasing timespec. - */ -static struct timespec persistent_ts; -static cycles_t cycles, last_cycles; -void read_persistent_clock(struct timespec *ts) -{ - unsigned long long nsecs; - cycles_t delta; - struct timespec *tsp = &persistent_ts; - - last_cycles = cycles; - cycles = clocksource_32k.read(&clocksource_32k); - delta = cycles - last_cycles; - - nsecs = clocksource_cyc2ns(delta, - clocksource_32k.mult, clocksource_32k.shift); - - timespec_add_ns(tsp, nsecs); - *ts = *tsp; -} - -static int __init omap_init_clocksource_32k(void) -{ - static char err[] __initdata = KERN_ERR - "%s: can't register clocksource!\n"; - - if (cpu_is_omap16xx() || cpu_class_is_omap2()) { - struct clk *sync_32k_ick; - - if (cpu_is_omap16xx()) - clocksource_32k.read = omap16xx_32k_read; - else if (cpu_is_omap2420()) - clocksource_32k.read = omap2420_32k_read; - else if (cpu_is_omap2430()) - clocksource_32k.read = omap2430_32k_read; - else if (cpu_is_omap34xx()) - clocksource_32k.read = omap34xx_32k_read; - else if (cpu_is_omap44xx()) - clocksource_32k.read = omap44xx_32k_read; - else - return -ENODEV; - - sync_32k_ick = clk_get(NULL, "omap_32ksync_ick"); - if (sync_32k_ick) - clk_enable(sync_32k_ick); - - clocksource_32k.mult = clocksource_hz2mult(32768, - clocksource_32k.shift); - - offset_32k = clocksource_32k.read(&clocksource_32k); - - if (clocksource_register(&clocksource_32k)) - printk(err, clocksource_32k.name); - } - return 0; -} -arch_initcall(omap_init_clocksource_32k); - -#endif /* !(defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP15XX)) */ - -/* Global address base setup code */ - -#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) - -static void __init __omap2_set_globals(struct omap_globals *omap2_globals) -{ - omap2_set_globals_tap(omap2_globals); - omap2_set_globals_sdrc(omap2_globals); - omap2_set_globals_control(omap2_globals); - omap2_set_globals_prcm(omap2_globals); -} - -#endif - -#if defined(CONFIG_ARCH_OMAP2420) - -static struct omap_globals omap242x_globals = { - .class = OMAP242X_CLASS, - .tap = OMAP2_L4_IO_ADDRESS(0x48014000), - .sdrc = OMAP2420_SDRC_BASE, - .sms = OMAP2420_SMS_BASE, - .ctrl = OMAP242X_CTRL_BASE, - .prm = OMAP2420_PRM_BASE, - .cm = OMAP2420_CM_BASE, -}; - -void __init omap2_set_globals_242x(void) -{ - __omap2_set_globals(&omap242x_globals); -} -#endif - -#if defined(CONFIG_ARCH_OMAP2430) - -static struct omap_globals omap243x_globals = { - .class = OMAP243X_CLASS, - .tap = OMAP2_L4_IO_ADDRESS(0x4900a000), - .sdrc = OMAP243X_SDRC_BASE, - .sms = OMAP243X_SMS_BASE, - .ctrl = OMAP243X_CTRL_BASE, - .prm = OMAP2430_PRM_BASE, - .cm = OMAP2430_CM_BASE, -}; - -void __init omap2_set_globals_243x(void) -{ - __omap2_set_globals(&omap243x_globals); -} -#endif - -#if defined(CONFIG_ARCH_OMAP3) - -static struct omap_globals omap3_globals = { - .class = OMAP343X_CLASS, - .tap = OMAP2_L4_IO_ADDRESS(0x4830A000), - .sdrc = OMAP343X_SDRC_BASE, - .sms = OMAP343X_SMS_BASE, - .ctrl = OMAP343X_CTRL_BASE, - .prm = OMAP3430_PRM_BASE, - .cm = OMAP3430_CM_BASE, -}; - -void __init omap2_set_globals_3xxx(void) -{ - __omap2_set_globals(&omap3_globals); -} - -void __init omap3_map_io(void) -{ - omap2_set_globals_3xxx(); - omap34xx_map_common_io(); -} -#endif - -#if defined(CONFIG_ARCH_OMAP4) -static struct omap_globals omap4_globals = { - .class = OMAP443X_CLASS, - .tap = OMAP2_L4_IO_ADDRESS(OMAP443X_SCM_BASE), - .ctrl = OMAP443X_SCM_BASE, - .ctrl_pad = OMAP443X_CTRL_BASE, - .prm = OMAP4430_PRM_BASE, - .cm = OMAP4430_CM_BASE, - .cm2 = OMAP4430_CM2_BASE, -}; - -void __init omap2_set_globals_443x(void) -{ - omap2_set_globals_tap(&omap4_globals); - omap2_set_globals_control(&omap4_globals); - omap2_set_globals_prcm(&omap4_globals); -} -#endif - diff --git a/arch/arm/plat-omap/counter_32k.c b/arch/arm/plat-omap/counter_32k.c new file mode 100644 index 0000000..155fe43 --- /dev/null +++ b/arch/arm/plat-omap/counter_32k.c @@ -0,0 +1,183 @@ +/* + * OMAP 32ksynctimer/counter_32k-related code + * + * Copyright (C) 2009 Texas Instruments + * Copyright (C) 2010 Nokia Corporation + * Tony Lindgren <tony@atomide.com> + * Added OMAP4 support - Santosh Shilimkar <santosh.shilimkar@ti.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * NOTE: This timer is not the same timer as the old OMAP1 MPU timer. + */ +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/clk.h> +#include <linux/io.h> + +#include <plat/common.h> +#include <plat/board.h> + +#include <plat/clock.h> + + +/* + * 32KHz clocksource ... always available, on pretty most chips except + * OMAP 730 and 1510. Other timers could be used as clocksources, with + * higher resolution in free-running counter modes (e.g. 12 MHz xtal), + * but systems won't necessarily want to spend resources that way. + */ + +#define OMAP16XX_TIMER_32K_SYNCHRONIZED 0xfffbc410 + +#if !(defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP15XX)) + +#include <linux/clocksource.h> + +/* + * offset_32k holds the init time counter value. It is then subtracted + * from every counter read to achieve a counter that counts time from the + * kernel boot (needed for sched_clock()). + */ +static u32 offset_32k __read_mostly; + +#ifdef CONFIG_ARCH_OMAP16XX +static cycle_t omap16xx_32k_read(struct clocksource *cs) +{ + return omap_readl(OMAP16XX_TIMER_32K_SYNCHRONIZED) - offset_32k; +} +#else +#define omap16xx_32k_read NULL +#endif + +#ifdef CONFIG_ARCH_OMAP2420 +static cycle_t omap2420_32k_read(struct clocksource *cs) +{ + return omap_readl(OMAP2420_32KSYNCT_BASE + 0x10) - offset_32k; +} +#else +#define omap2420_32k_read NULL +#endif + +#ifdef CONFIG_ARCH_OMAP2430 +static cycle_t omap2430_32k_read(struct clocksource *cs) +{ + return omap_readl(OMAP2430_32KSYNCT_BASE + 0x10) - offset_32k; +} +#else +#define omap2430_32k_read NULL +#endif + +#ifdef CONFIG_ARCH_OMAP3 +static cycle_t omap34xx_32k_read(struct clocksource *cs) +{ + return omap_readl(OMAP3430_32KSYNCT_BASE + 0x10) - offset_32k; +} +#else +#define omap34xx_32k_read NULL +#endif + +#ifdef CONFIG_ARCH_OMAP4 +static cycle_t omap44xx_32k_read(struct clocksource *cs) +{ + return omap_readl(OMAP4430_32KSYNCT_BASE + 0x10) - offset_32k; +} +#else +#define omap44xx_32k_read NULL +#endif + +/* + * Kernel assumes that sched_clock can be called early but may not have + * things ready yet. + */ +static cycle_t omap_32k_read_dummy(struct clocksource *cs) +{ + return 0; +} + +static struct clocksource clocksource_32k = { + .name = "32k_counter", + .rating = 250, + .read = omap_32k_read_dummy, + .mask = CLOCKSOURCE_MASK(32), + .shift = 10, + .flags = CLOCK_SOURCE_IS_CONTINUOUS, +}; + +/* + * Returns current time from boot in nsecs. It's OK for this to wrap + * around for now, as it's just a relative time stamp. + */ +unsigned long long sched_clock(void) +{ + return clocksource_cyc2ns(clocksource_32k.read(&clocksource_32k), + clocksource_32k.mult, clocksource_32k.shift); +} + +/** + * read_persistent_clock - Return time from a persistent clock. + * + * Reads the time from a source which isn't disabled during PM, the + * 32k sync timer. Convert the cycles elapsed since last read into + * nsecs and adds to a monotonically increasing timespec. + */ +static struct timespec persistent_ts; +static cycles_t cycles, last_cycles; +void read_persistent_clock(struct timespec *ts) +{ + unsigned long long nsecs; + cycles_t delta; + struct timespec *tsp = &persistent_ts; + + last_cycles = cycles; + cycles = clocksource_32k.read(&clocksource_32k); + delta = cycles - last_cycles; + + nsecs = clocksource_cyc2ns(delta, + clocksource_32k.mult, clocksource_32k.shift); + + timespec_add_ns(tsp, nsecs); + *ts = *tsp; +} + +static int __init omap_init_clocksource_32k(void) +{ + static char err[] __initdata = KERN_ERR + "%s: can't register clocksource!\n"; + + if (cpu_is_omap16xx() || cpu_class_is_omap2()) { + struct clk *sync_32k_ick; + + if (cpu_is_omap16xx()) + clocksource_32k.read = omap16xx_32k_read; + else if (cpu_is_omap2420()) + clocksource_32k.read = omap2420_32k_read; + else if (cpu_is_omap2430()) + clocksource_32k.read = omap2430_32k_read; + else if (cpu_is_omap34xx()) + clocksource_32k.read = omap34xx_32k_read; + else if (cpu_is_omap44xx()) + clocksource_32k.read = omap44xx_32k_read; + else + return -ENODEV; + + sync_32k_ick = clk_get(NULL, "omap_32ksync_ick"); + if (sync_32k_ick) + clk_enable(sync_32k_ick); + + clocksource_32k.mult = clocksource_hz2mult(32768, + clocksource_32k.shift); + + offset_32k = clocksource_32k.read(&clocksource_32k); + + if (clocksource_register(&clocksource_32k)) + printk(err, clocksource_32k.name); + } + return 0; +} +arch_initcall(omap_init_clocksource_32k); + +#endif /* !(defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP15XX)) */ + diff --git a/arch/arm/plat-omap/devices.c b/arch/arm/plat-omap/devices.c index 8e88e0e..1e2383e 100644 --- a/arch/arm/plat-omap/devices.c +++ b/arch/arm/plat-omap/devices.c @@ -21,7 +21,6 @@ #include <asm/mach/map.h> #include <plat/tc.h> -#include <plat/control.h> #include <plat/board.h> #include <plat/mmc.h> #include <mach/gpio.h> diff --git a/arch/arm/plat-omap/sram.c b/arch/arm/plat-omap/sram.c index dba5704..c209163 100644 --- a/arch/arm/plat-omap/sram.c +++ b/arch/arm/plat-omap/sram.c @@ -31,10 +31,8 @@ #include <plat/cpu.h> #include <plat/vram.h> -#include <plat/control.h> #include "sram.h" #include "fb.h" - #if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) # include "../mach-omap2/prm.h" # include "../mach-omap2/cm.h" @@ -71,7 +69,6 @@ #define OMAP34XX_VA_WRITEPERM0 OMAP2_L3_IO_ADDRESS(0x68012858) #define OMAP34XX_VA_ADDR_MATCH2 OMAP2_L3_IO_ADDRESS(0x68012880) #define OMAP34XX_VA_SMS_RG_ATT0 OMAP2_L3_IO_ADDRESS(0x6C000048) -#define OMAP34XX_VA_CONTROL_STAT OMAP2_L4_IO_ADDRESS(0x480022F0) #define GP_DEVICE 0x300 |
