diff options
Diffstat (limited to 'arch/arm/plat-omap/include/plat')
| -rw-r--r-- | arch/arm/plat-omap/include/plat/board.h | 38 | ||||
| -rw-r--r-- | arch/arm/plat-omap/include/plat/clock.h | 2 | ||||
| -rw-r--r-- | arch/arm/plat-omap/include/plat/dmtimer.h | 22 | ||||
| -rw-r--r-- | arch/arm/plat-omap/include/plat/dsp.h | 3 | ||||
| -rw-r--r-- | arch/arm/plat-omap/include/plat/omap_hwmod.h | 2 | ||||
| -rw-r--r-- | arch/arm/plat-omap/include/plat/serial.h | 4 | ||||
| -rw-r--r-- | arch/arm/plat-omap/include/plat/uncompress.h | 6 | ||||
| -rw-r--r-- | arch/arm/plat-omap/include/plat/usb.h | 196 |
8 files changed, 22 insertions, 251 deletions
diff --git a/arch/arm/plat-omap/include/plat/board.h b/arch/arm/plat-omap/include/plat/board.h index 4814c5b..e62f20a 100644 --- a/arch/arm/plat-omap/include/plat/board.h +++ b/arch/arm/plat-omap/include/plat/board.h @@ -57,44 +57,6 @@ struct omap_camera_sensor_config { int (*power_off)(void * data); }; -struct omap_usb_config { - /* Configure drivers according to the connectors on your board: - * - "A" connector (rectagular) - * ... for host/OHCI use, set "register_host". - * - "B" connector (squarish) or "Mini-B" - * ... for device/gadget use, set "register_dev". - * - "Mini-AB" connector (very similar to Mini-B) - * ... for OTG use as device OR host, initialize "otg" - */ - unsigned register_host:1; - unsigned register_dev:1; - u8 otg; /* port number, 1-based: usb1 == 2 */ - - u8 hmc_mode; - - /* implicitly true if otg: host supports remote wakeup? */ - u8 rwc; - - /* signaling pins used to talk to transceiver on usbN: - * 0 == usbN unused - * 2 == usb0-only, using internal transceiver - * 3 == 3 wire bidirectional - * 4 == 4 wire bidirectional - * 6 == 6 wire unidirectional (or TLL) - */ - u8 pins[3]; - - struct platform_device *udc_device; - struct platform_device *ohci_device; - struct platform_device *otg_device; - - u32 (*usb0_init)(unsigned nwires, unsigned is_device); - u32 (*usb1_init)(unsigned nwires); - u32 (*usb2_init)(unsigned nwires, unsigned alt_pingroup); - - int (*ocpi_enable)(void); -}; - struct omap_lcd_config { char panel_name[16]; char ctrl_name[16]; diff --git a/arch/arm/plat-omap/include/plat/clock.h b/arch/arm/plat-omap/include/plat/clock.h index d0ef57c..656b986 100644 --- a/arch/arm/plat-omap/include/plat/clock.h +++ b/arch/arm/plat-omap/include/plat/clock.h @@ -156,7 +156,6 @@ struct dpll_data { u8 min_divider; u16 max_divider; u8 modes; -#if defined(CONFIG_ARCH_OMAP3) || defined(CONFIG_ARCH_OMAP4) void __iomem *autoidle_reg; void __iomem *idlest_reg; u32 autoidle_mask; @@ -167,7 +166,6 @@ struct dpll_data { u8 auto_recal_bit; u8 recal_en_bit; u8 recal_st_bit; -# endif u8 flags; }; diff --git a/arch/arm/plat-omap/include/plat/dmtimer.h b/arch/arm/plat-omap/include/plat/dmtimer.h index 5da7356..19e7fa5 100644 --- a/arch/arm/plat-omap/include/plat/dmtimer.h +++ b/arch/arm/plat-omap/include/plat/dmtimer.h @@ -55,23 +55,17 @@ #define OMAP_TIMER_TRIGGER_OVERFLOW 0x01 #define OMAP_TIMER_TRIGGER_OVERFLOW_AND_COMPARE 0x02 -/* - * IP revision identifier so that Highlander IP - * in OMAP4 can be distinguished. - */ -#define OMAP_TIMER_IP_VERSION_1 0x1 - /* timer capabilities used in hwmod database */ #define OMAP_TIMER_SECURE 0x80000000 #define OMAP_TIMER_ALWON 0x40000000 #define OMAP_TIMER_HAS_PWM 0x20000000 +#define OMAP_TIMER_NEEDS_RESET 0x10000000 struct omap_timer_capability_dev_attr { u32 timer_capability; }; struct omap_dm_timer; -struct clk; struct timer_regs { u32 tidr; @@ -96,16 +90,12 @@ struct timer_regs { }; struct dmtimer_platform_data { + /* set_timer_src - Only used for OMAP1 devices */ int (*set_timer_src)(struct platform_device *pdev, int source); - int timer_ip_version; - u32 needs_manual_reset:1; - bool reserved; - - bool loses_context; - - int (*get_context_loss_count)(struct device *dev); + u32 timer_capability; }; +int omap_dm_timer_reserve_systimer(int id); struct omap_dm_timer *omap_dm_timer_request(void); struct omap_dm_timer *omap_dm_timer_request_specific(int timer_id); int omap_dm_timer_free(struct omap_dm_timer *timer); @@ -272,13 +262,11 @@ struct omap_dm_timer { unsigned reserved:1; unsigned posted:1; struct timer_regs context; - bool loses_context; int ctx_loss_count; int revision; + u32 capability; struct platform_device *pdev; struct list_head node; - - int (*get_context_loss_count)(struct device *dev); }; int omap_dm_timer_prepare(struct omap_dm_timer *timer); diff --git a/arch/arm/plat-omap/include/plat/dsp.h b/arch/arm/plat-omap/include/plat/dsp.h index 9c604b3..5927709 100644 --- a/arch/arm/plat-omap/include/plat/dsp.h +++ b/arch/arm/plat-omap/include/plat/dsp.h @@ -18,6 +18,9 @@ struct omap_dsp_platform_data { u32 (*dsp_cm_read)(s16 , u16); u32 (*dsp_cm_rmw_bits)(u32, u32, s16, s16); + void (*set_bootaddr)(u32); + void (*set_bootmode)(u8); + phys_addr_t phys_mempool_base; phys_addr_t phys_mempool_size; }; diff --git a/arch/arm/plat-omap/include/plat/omap_hwmod.h b/arch/arm/plat-omap/include/plat/omap_hwmod.h index c835b71..a8ecc53 100644 --- a/arch/arm/plat-omap/include/plat/omap_hwmod.h +++ b/arch/arm/plat-omap/include/plat/omap_hwmod.h @@ -629,6 +629,8 @@ int omap_hwmod_no_setup_reset(struct omap_hwmod *oh); int omap_hwmod_pad_route_irq(struct omap_hwmod *oh, int pad_idx, int irq_idx); +extern void __init omap_hwmod_init(void); + /* * Chip variant-specific hwmod init routines - XXX should be converted * to use initcalls once the initial boot ordering is straightened out diff --git a/arch/arm/plat-omap/include/plat/serial.h b/arch/arm/plat-omap/include/plat/serial.h index b073e5f..28e2d25 100644 --- a/arch/arm/plat-omap/include/plat/serial.h +++ b/arch/arm/plat-omap/include/plat/serial.h @@ -60,6 +60,9 @@ /* AM3505/3517 UART4 */ #define AM35XX_UART4_BASE 0x4809E000 /* Only on AM3505/3517 */ +/* AM33XX serial port */ +#define AM33XX_UART1_BASE 0x44E09000 + /* External port on Zoom2/3 */ #define ZOOM_UART_BASE 0x10000000 #define ZOOM_UART_VIRT 0xfa400000 @@ -93,6 +96,7 @@ #define TI81XXUART1 81 #define TI81XXUART2 82 #define TI81XXUART3 83 +#define AM33XXUART1 84 #define ZOOM_UART 95 /* Only on zoom2/3 */ /* This is only used by 8250.c for omap1510 */ diff --git a/arch/arm/plat-omap/include/plat/uncompress.h b/arch/arm/plat-omap/include/plat/uncompress.h index cc3f11b..ac43233 100644 --- a/arch/arm/plat-omap/include/plat/uncompress.h +++ b/arch/arm/plat-omap/include/plat/uncompress.h @@ -103,6 +103,10 @@ static inline void flush(void) _DEBUG_LL_ENTRY(mach, TI81XX_UART##p##_BASE, OMAP_PORT_SHIFT, \ TI81XXUART##p) +#define DEBUG_LL_AM33XX(p, mach) \ + _DEBUG_LL_ENTRY(mach, AM33XX_UART##p##_BASE, OMAP_PORT_SHIFT, \ + AM33XXUART##p) + static inline void __arch_decomp_setup(unsigned long arch_id) { int port = 0; @@ -183,6 +187,8 @@ static inline void __arch_decomp_setup(unsigned long arch_id) /* TI8148 base boards using UART1 */ DEBUG_LL_TI81XX(1, ti8148evm); + /* AM33XX base boards using UART1 */ + DEBUG_LL_AM33XX(1, am335xevm); } while (0); } diff --git a/arch/arm/plat-omap/include/plat/usb.h b/arch/arm/plat-omap/include/plat/usb.h index 762eeb06..548a4c8 100644 --- a/arch/arm/plat-omap/include/plat/usb.h +++ b/arch/arm/plat-omap/include/plat/usb.h @@ -44,6 +44,8 @@ struct usbhs_omap_board_data { struct regulator *regulator[OMAP3_HS_USB_PORTS]; }; +#ifdef CONFIG_ARCH_OMAP2PLUS + struct ehci_hcd_omap_platform_data { enum usbhs_omap_port_mode port_mode[OMAP3_HS_USB_PORTS]; int reset_gpio_port[OMAP3_HS_USB_PORTS]; @@ -64,26 +66,6 @@ struct usbhs_omap_platform_data { }; /*-------------------------------------------------------------------------*/ -#define OMAP1_OTG_BASE 0xfffb0400 -#define OMAP1_UDC_BASE 0xfffb4000 -#define OMAP1_OHCI_BASE 0xfffba000 - -#define OMAP2_OHCI_BASE 0x4805e000 -#define OMAP2_UDC_BASE 0x4805e200 -#define OMAP2_OTG_BASE 0x4805e300 - -#ifdef CONFIG_ARCH_OMAP1 - -#define OTG_BASE OMAP1_OTG_BASE -#define UDC_BASE OMAP1_UDC_BASE -#define OMAP_OHCI_BASE OMAP1_OHCI_BASE - -#else - -#define OTG_BASE OMAP2_OTG_BASE -#define UDC_BASE OMAP2_UDC_BASE -#define OMAP_OHCI_BASE OMAP2_OHCI_BASE - struct omap_musb_board_data { u8 interface_type; u8 mode; @@ -107,44 +89,6 @@ extern int omap4430_phy_init(struct device *dev); extern int omap4430_phy_exit(struct device *dev); extern int omap4430_phy_suspend(struct device *dev, int suspend); -/* - * NOTE: Please update omap USB drivers to use ioremap + read/write - */ - -#define OMAP2_L4_IO_OFFSET 0xb2000000 -#define OMAP2_L4_IO_ADDRESS(pa) IOMEM((pa) + OMAP2_L4_IO_OFFSET) - -static inline u8 omap_readb(u32 pa) -{ - return __raw_readb(OMAP2_L4_IO_ADDRESS(pa)); -} - -static inline u16 omap_readw(u32 pa) -{ - return __raw_readw(OMAP2_L4_IO_ADDRESS(pa)); -} - -static inline u32 omap_readl(u32 pa) -{ - return __raw_readl(OMAP2_L4_IO_ADDRESS(pa)); -} - -static inline void omap_writeb(u8 v, u32 pa) -{ - __raw_writeb(v, OMAP2_L4_IO_ADDRESS(pa)); -} - - -static inline void omap_writew(u16 v, u32 pa) -{ - __raw_writew(v, OMAP2_L4_IO_ADDRESS(pa)); -} - -static inline void omap_writel(u32 v, u32 pa) -{ - __raw_writel(v, OMAP2_L4_IO_ADDRESS(pa)); -} - #endif extern void am35x_musb_reset(void); @@ -153,142 +97,6 @@ extern void am35x_musb_clear_irq(void); extern void am35x_set_mode(u8 musb_mode); extern void ti81xx_musb_phy_power(u8 on); -/* - * FIXME correct answer depends on hmc_mode, - * as does (on omap1) any nonzero value for config->otg port number - */ -#ifdef CONFIG_USB_GADGET_OMAP -#define is_usb0_device(config) 1 -#else -#define is_usb0_device(config) 0 -#endif - -void omap_otg_init(struct omap_usb_config *config); - -#if defined(CONFIG_USB) || defined(CONFIG_USB_MODULE) -void omap1_usb_init(struct omap_usb_config *pdata); -#else -static inline void omap1_usb_init(struct omap_usb_config *pdata) -{ -} -#endif - -#if defined(CONFIG_ARCH_OMAP_OTG) || defined(CONFIG_ARCH_OMAP_OTG_MODULE) -void omap2_usbfs_init(struct omap_usb_config *pdata); -#else -static inline void omap2_usbfs_init(struct omap_usb_config *pdata) -{ -} -#endif - -/*-------------------------------------------------------------------------*/ - -/* - * OTG and transceiver registers, for OMAPs starting with ARM926 - */ -#define OTG_REV (OTG_BASE + 0x00) -#define OTG_SYSCON_1 (OTG_BASE + 0x04) -# define USB2_TRX_MODE(w) (((w)>>24)&0x07) -# define USB1_TRX_MODE(w) (((w)>>20)&0x07) -# define USB0_TRX_MODE(w) (((w)>>16)&0x07) -# define OTG_IDLE_EN (1 << 15) -# define HST_IDLE_EN (1 << 14) -# define DEV_IDLE_EN (1 << 13) -# define OTG_RESET_DONE (1 << 2) -# define OTG_SOFT_RESET (1 << 1) -#define OTG_SYSCON_2 (OTG_BASE + 0x08) -# define OTG_EN (1 << 31) -# define USBX_SYNCHRO (1 << 30) -# define OTG_MST16 (1 << 29) -# define SRP_GPDATA (1 << 28) -# define SRP_GPDVBUS (1 << 27) -# define SRP_GPUVBUS(w) (((w)>>24)&0x07) -# define A_WAIT_VRISE(w) (((w)>>20)&0x07) -# define B_ASE_BRST(w) (((w)>>16)&0x07) -# define SRP_DPW (1 << 14) -# define SRP_DATA (1 << 13) -# define SRP_VBUS (1 << 12) -# define OTG_PADEN (1 << 10) -# define HMC_PADEN (1 << 9) -# define UHOST_EN (1 << 8) -# define HMC_TLLSPEED (1 << 7) -# define HMC_TLLATTACH (1 << 6) -# define OTG_HMC(w) (((w)>>0)&0x3f) -#define OTG_CTRL (OTG_BASE + 0x0c) -# define OTG_USB2_EN (1 << 29) -# define OTG_USB2_DP (1 << 28) -# define OTG_USB2_DM (1 << 27) -# define OTG_USB1_EN (1 << 26) -# define OTG_USB1_DP (1 << 25) -# define OTG_USB1_DM (1 << 24) -# define OTG_USB0_EN (1 << 23) -# define OTG_USB0_DP (1 << 22) -# define OTG_USB0_DM (1 << 21) -# define OTG_ASESSVLD (1 << 20) -# define OTG_BSESSEND (1 << 19) -# define OTG_BSESSVLD (1 << 18) -# define OTG_VBUSVLD (1 << 17) -# define OTG_ID (1 << 16) -# define OTG_DRIVER_SEL (1 << 15) -# define OTG_A_SETB_HNPEN (1 << 12) -# define OTG_A_BUSREQ (1 << 11) -# define OTG_B_HNPEN (1 << 9) -# define OTG_B_BUSREQ (1 << 8) -# define OTG_BUSDROP (1 << 7) -# define OTG_PULLDOWN (1 << 5) -# define OTG_PULLUP (1 << 4) -# define OTG_DRV_VBUS (1 << 3) -# define OTG_PD_VBUS (1 << 2) -# define OTG_PU_VBUS (1 << 1) -# define OTG_PU_ID (1 << 0) -#define OTG_IRQ_EN (OTG_BASE + 0x10) /* 16-bit */ -# define DRIVER_SWITCH (1 << 15) -# define A_VBUS_ERR (1 << 13) -# define A_REQ_TMROUT (1 << 12) -# define A_SRP_DETECT (1 << 11) -# define B_HNP_FAIL (1 << 10) -# define B_SRP_TMROUT (1 << 9) -# define B_SRP_DONE (1 << 8) -# define B_SRP_STARTED (1 << 7) -# define OPRT_CHG (1 << 0) -#define OTG_IRQ_SRC (OTG_BASE + 0x14) /* 16-bit */ - // same bits as in IRQ_EN -#define OTG_OUTCTRL (OTG_BASE + 0x18) /* 16-bit */ -# define OTGVPD (1 << 14) -# define OTGVPU (1 << 13) -# define OTGPUID (1 << 12) -# define USB2VDR (1 << 10) -# define USB2PDEN (1 << 9) -# define USB2PUEN (1 << 8) -# define USB1VDR (1 << 6) -# define USB1PDEN (1 << 5) -# define USB1PUEN (1 << 4) -# define USB0VDR (1 << 2) -# define USB0PDEN (1 << 1) -# define USB0PUEN (1 << 0) -#define OTG_TEST (OTG_BASE + 0x20) /* 16-bit */ -#define OTG_VENDOR_CODE (OTG_BASE + 0xfc) /* 16-bit */ - -/*-------------------------------------------------------------------------*/ - -/* OMAP1 */ -#define USB_TRANSCEIVER_CTRL (0xfffe1000 + 0x0064) -# define CONF_USB2_UNI_R (1 << 8) -# define CONF_USB1_UNI_R (1 << 7) -# define CONF_USB_PORT0_R(x) (((x)>>4)&0x7) -# define CONF_USB0_ISOLATE_R (1 << 3) -# define CONF_USB_PWRDN_DM_R (1 << 2) -# define CONF_USB_PWRDN_DP_R (1 << 1) - -/* OMAP2 */ -# define USB_UNIDIR 0x0 -# define USB_UNIDIR_TLL 0x1 -# define USB_BIDIR 0x2 -# define USB_BIDIR_TLL 0x3 -# define USBTXWRMODEI(port, x) ((x) << (22 - (port * 2))) -# define USBT2TLL5PI (1 << 17) -# define USB0PUENACTLOI (1 << 16) -# define USBSTANDBYCTRL (1 << 15) /* AM35x */ /* USB 2.0 PHY Control */ #define CONF2_PHY_GPIOMODE (1 << 23) |
