diff options
Diffstat (limited to 'arch/arm/mach-u300/i2c.c')
| -rw-r--r-- | arch/arm/mach-u300/i2c.c | 249 |
1 files changed, 249 insertions, 0 deletions
diff --git a/arch/arm/mach-u300/i2c.c b/arch/arm/mach-u300/i2c.c index 10be1f8..c73ed06 100644 --- a/arch/arm/mach-u300/i2c.c +++ b/arch/arm/mach-u300/i2c.c @@ -9,13 +9,257 @@ */ #include <linux/kernel.h> #include <linux/i2c.h> +#include <linux/mfd/ab3100.h> +#include <linux/regulator/machine.h> +#include <linux/amba/bus.h> #include <mach/irqs.h> +/* + * Initial settings of ab3100 registers. + * Common for below LDO regulator settings are that + * bit 7-5 controls voltage. Bit 4 turns regulator ON(1) or OFF(0). + * Bit 3-2 controls sleep enable and bit 1-0 controls sleep mode. + */ + +/* LDO_A 0x16: 2.75V, ON, SLEEP_A, SLEEP OFF GND */ +#define LDO_A_SETTING 0x16 +/* LDO_C 0x10: 2.65V, ON, SLEEP_A or B, SLEEP full power */ +#define LDO_C_SETTING 0x10 +/* LDO_D 0x10: 2.65V, ON, sleep mode not used */ +#define LDO_D_SETTING 0x10 +/* LDO_E 0x10: 1.8V, ON, SLEEP_A or B, SLEEP full power */ +#define LDO_E_SETTING 0x10 +/* LDO_E SLEEP 0x00: 1.8V, not used, SLEEP_A or B, not used */ +#define LDO_E_SLEEP_SETTING 0x00 +/* LDO_F 0xD0: 2.5V, ON, SLEEP_A or B, SLEEP full power */ +#define LDO_F_SETTING 0xD0 +/* LDO_G 0x00: 2.85V, OFF, SLEEP_A or B, SLEEP full power */ +#define LDO_G_SETTING 0x00 +/* LDO_H 0x18: 2.75V, ON, SLEEP_B, SLEEP full power */ +#define LDO_H_SETTING 0x18 +/* LDO_K 0x00: 2.75V, OFF, SLEEP_A or B, SLEEP full power */ +#define LDO_K_SETTING 0x00 +/* LDO_EXT 0x00: Voltage not set, OFF, not used, not used */ +#define LDO_EXT_SETTING 0x00 +/* BUCK 0x7D: 1.2V, ON, SLEEP_A and B, SLEEP low power */ +#define BUCK_SETTING 0x7D +/* BUCK SLEEP 0xAC: 1.05V, Not used, SLEEP_A and B, Not used */ +#define BUCK_SLEEP_SETTING 0xAC + +static struct regulator_consumer_supply supply_ldo_c[] = { + { + .dev_name = "ab3100-codec", + .supply = "vaudio", /* Powers the codec */ + }, +}; + +/* + * This one needs to be a supply so we can turn it off + * in order to shut down the system. + */ +static struct regulator_consumer_supply supply_ldo_d[] = { + { + .dev = NULL, + .supply = "vana15", /* Powers the SoC (CPU etc) */ + }, +}; + +static struct regulator_consumer_supply supply_ldo_g[] = { + { + .dev_name = "mmci", + .supply = "vmmc", /* Powers MMC/SD card */ + }, +}; + +static struct regulator_consumer_supply supply_ldo_h[] = { + { + .dev_name = "xgam_pdi", + .supply = "vdisp", /* Powers camera, display etc */ + }, +}; + +static struct regulator_consumer_supply supply_ldo_k[] = { + { + .dev_name = "irda", + .supply = "vir", /* Power IrDA */ + }, +}; + +/* + * This is a placeholder for whoever wish to use the + * external power. + */ +static struct regulator_consumer_supply supply_ldo_ext[] = { + { + .dev = NULL, + .supply = "vext", /* External power */ + }, +}; + +/* Preset (hardware defined) voltages for these regulators */ +#define LDO_A_VOLTAGE 2750000 +#define LDO_C_VOLTAGE 2650000 +#define LDO_D_VOLTAGE 2650000 + +static struct ab3100_platform_data ab3100_plf_data = { + .reg_constraints = { + /* LDO A routing and constraints */ + { + .constraints = { + .name = "vrad", + .min_uV = LDO_A_VOLTAGE, + .max_uV = LDO_A_VOLTAGE, + .valid_modes_mask = REGULATOR_MODE_NORMAL, + .always_on = 1, + .boot_on = 1, + }, + }, + /* LDO C routing and constraints */ + { + .constraints = { + .min_uV = LDO_C_VOLTAGE, + .max_uV = LDO_C_VOLTAGE, + .valid_modes_mask = REGULATOR_MODE_NORMAL, + }, + .num_consumer_supplies = ARRAY_SIZE(supply_ldo_c), + .consumer_supplies = supply_ldo_c, + }, + /* LDO D routing and constraints */ + { + .constraints = { + .min_uV = LDO_D_VOLTAGE, + .max_uV = LDO_D_VOLTAGE, + .valid_modes_mask = REGULATOR_MODE_NORMAL, + .valid_ops_mask = REGULATOR_CHANGE_STATUS, + /* + * Actually this is boot_on but we need + * to reference count it externally to + * be able to shut down the system. + */ + }, + .num_consumer_supplies = ARRAY_SIZE(supply_ldo_d), + .consumer_supplies = supply_ldo_d, + }, + /* LDO E routing and constraints */ + { + .constraints = { + .name = "vio", + .min_uV = 1800000, + .max_uV = 1800000, + .valid_modes_mask = REGULATOR_MODE_NORMAL, + .valid_ops_mask = + REGULATOR_CHANGE_VOLTAGE | + REGULATOR_CHANGE_STATUS, + .always_on = 1, + .boot_on = 1, + }, + }, + /* LDO F routing and constraints */ + { + .constraints = { + .name = "vana25", + .min_uV = 2500000, + .max_uV = 2500000, + .valid_modes_mask = REGULATOR_MODE_NORMAL, + .valid_ops_mask = + REGULATOR_CHANGE_VOLTAGE | + REGULATOR_CHANGE_STATUS, + .always_on = 1, + .boot_on = 1, + }, + }, + /* LDO G routing and constraints */ + { + .constraints = { + .min_uV = 1500000, + .max_uV = 2850000, + .valid_modes_mask = REGULATOR_MODE_NORMAL, + .valid_ops_mask = + REGULATOR_CHANGE_VOLTAGE | + REGULATOR_CHANGE_STATUS, + }, + .num_consumer_supplies = ARRAY_SIZE(supply_ldo_g), + .consumer_supplies = supply_ldo_g, + }, + /* LDO H routing and constraints */ + { + .constraints = { + .min_uV = 1200000, + .max_uV = 2750000, + .valid_modes_mask = REGULATOR_MODE_NORMAL, + .valid_ops_mask = + REGULATOR_CHANGE_VOLTAGE | + REGULATOR_CHANGE_STATUS, + }, + .num_consumer_supplies = ARRAY_SIZE(supply_ldo_h), + .consumer_supplies = supply_ldo_h, + }, + /* LDO K routing and constraints */ + { + .constraints = { + .min_uV = 1800000, + .max_uV = 2750000, + .valid_modes_mask = REGULATOR_MODE_NORMAL, + .valid_ops_mask = + REGULATOR_CHANGE_VOLTAGE | + REGULATOR_CHANGE_STATUS, + }, + .num_consumer_supplies = ARRAY_SIZE(supply_ldo_k), + .consumer_supplies = supply_ldo_k, + }, + /* External regulator interface. No fixed voltage specified. + * If we knew the voltage of the external regulator and it + * was connected on the board, we could add the (fixed) + * voltage for it here. + */ + { + .constraints = { + .min_uV = 0, + .max_uV = 0, + .valid_modes_mask = REGULATOR_MODE_NORMAL, + .valid_ops_mask = + REGULATOR_CHANGE_STATUS, + }, + .num_consumer_supplies = ARRAY_SIZE(supply_ldo_ext), + .consumer_supplies = supply_ldo_ext, + }, + /* Buck converter routing and constraints */ + { + .constraints = { + .name = "vcore", + .min_uV = 1200000, + .max_uV = 1800000, + .valid_modes_mask = REGULATOR_MODE_NORMAL, + .valid_ops_mask = + REGULATOR_CHANGE_VOLTAGE | + REGULATOR_CHANGE_STATUS, + .always_on = 1, + .boot_on = 1, + }, + }, + }, + .reg_initvals = { + LDO_A_SETTING, + LDO_C_SETTING, + LDO_E_SETTING, + LDO_E_SLEEP_SETTING, + LDO_F_SETTING, + LDO_G_SETTING, + LDO_H_SETTING, + LDO_K_SETTING, + LDO_EXT_SETTING, + BUCK_SETTING, + BUCK_SLEEP_SETTING, + LDO_D_SETTING, + }, +}; + static struct i2c_board_info __initdata bus0_i2c_board_info[] = { { .type = "ab3100", .addr = 0x48, .irq = IRQ_U300_IRQ0_EXT, + .platform_data = &ab3100_plf_data, }, }; @@ -38,6 +282,11 @@ void __init u300_i2c_register_board_devices(void) { i2c_register_board_info(0, bus0_i2c_board_info, ARRAY_SIZE(bus0_i2c_board_info)); + /* + * This makes the core shut down all unused regulators + * after all the initcalls have completed. + */ + regulator_has_full_constraints(); i2c_register_board_info(1, bus1_i2c_board_info, ARRAY_SIZE(bus1_i2c_board_info)); } |
