diff options
Diffstat (limited to 'arch/arm/mach-sa1100/include/mach/simpad.h')
| -rw-r--r-- | arch/arm/mach-sa1100/include/mach/simpad.h | 112 |
1 files changed, 112 insertions, 0 deletions
diff --git a/arch/arm/mach-sa1100/include/mach/simpad.h b/arch/arm/mach-sa1100/include/mach/simpad.h new file mode 100644 index 0000000..9296c45 --- /dev/null +++ b/arch/arm/mach-sa1100/include/mach/simpad.h @@ -0,0 +1,112 @@ +/* + * arch/arm/mach-sa1100/include/mach/simpad.h + * + * based of assabet.h same as HUW_Webpanel + * + * This file contains the hardware specific definitions for SIMpad + * + * 2001/05/14 Juergen Messerer <juergen.messerer@freesurf.ch> + */ + +#ifndef __ASM_ARCH_SIMPAD_H +#define __ASM_ARCH_SIMPAD_H + + +#define GPIO_UART1_RTS GPIO_GPIO14 +#define GPIO_UART1_DTR GPIO_GPIO7 +#define GPIO_UART1_CTS GPIO_GPIO8 +#define GPIO_UART1_DCD GPIO_GPIO23 +#define GPIO_UART1_DSR GPIO_GPIO6 + +#define GPIO_UART3_RTS GPIO_GPIO12 +#define GPIO_UART3_DTR GPIO_GPIO16 +#define GPIO_UART3_CTS GPIO_GPIO13 +#define GPIO_UART3_DCD GPIO_GPIO18 +#define GPIO_UART3_DSR GPIO_GPIO17 + +#define GPIO_POWER_BUTTON GPIO_GPIO0 +#define GPIO_UCB1300_IRQ GPIO_GPIO22 /* UCB GPIO and touchscreen */ + +#define IRQ_UART1_CTS IRQ_GPIO15 +#define IRQ_UART1_DCD GPIO_GPIO23 +#define IRQ_UART1_DSR GPIO_GPIO6 +#define IRQ_UART3_CTS GPIO_GPIO13 +#define IRQ_UART3_DCD GPIO_GPIO18 +#define IRQ_UART3_DSR GPIO_GPIO17 + +#define IRQ_GPIO_UCB1300_IRQ IRQ_GPIO22 +#define IRQ_GPIO_POWER_BUTTON IRQ_GPIO0 + + +/*--- PCMCIA ---*/ +#define GPIO_CF_CD GPIO_GPIO24 +#define GPIO_CF_IRQ GPIO_GPIO1 +#define IRQ_GPIO_CF_IRQ IRQ_GPIO1 +#define IRQ_GPIO_CF_CD IRQ_GPIO24 + +/*--- SmartCard ---*/ +#define GPIO_SMART_CARD GPIO_GPIO10 +#define IRQ_GPIO_SMARD_CARD IRQ_GPIO10 + +// CS3 Latch is write only, a shadow is necessary + +#define CS3BUSTYPE unsigned volatile long +#define CS3_BASE 0xf1000000 + +#define VCC_5V_EN 0x0001 // For 5V PCMCIA +#define VCC_3V_EN 0x0002 // FOR 3.3V PCMCIA +#define EN1 0x0004 // This is only for EPROM's +#define EN0 0x0008 // Both should be enable for 3.3V or 5V +#define DISPLAY_ON 0x0010 +#define PCMCIA_BUFF_DIS 0x0020 +#define MQ_RESET 0x0040 +#define PCMCIA_RESET 0x0080 +#define DECT_POWER_ON 0x0100 +#define IRDA_SD 0x0200 // Shutdown for powersave +#define RS232_ON 0x0400 +#define SD_MEDIAQ 0x0800 // Shutdown for powersave +#define LED2_ON 0x1000 +#define IRDA_MODE 0x2000 // Fast/Slow IrDA mode +#define ENABLE_5V 0x4000 // Enable 5V circuit +#define RESET_SIMCARD 0x8000 + +#define RS232_ENABLE 0x0440 +#define PCMCIAMASK 0x402f + + +struct simpad_battery { + unsigned char ac_status; /* line connected yes/no */ + unsigned char status; /* battery loading yes/no */ + unsigned char percentage; /* percentage loaded */ + unsigned short life; /* life till empty */ +}; + +/* These should match the apm_bios.h definitions */ +#define SIMPAD_AC_STATUS_AC_OFFLINE 0x00 +#define SIMPAD_AC_STATUS_AC_ONLINE 0x01 +#define SIMPAD_AC_STATUS_AC_BACKUP 0x02 /* What does this mean? */ +#define SIMPAD_AC_STATUS_AC_UNKNOWN 0xff + +/* These bitfields are rarely "or'd" together */ +#define SIMPAD_BATT_STATUS_HIGH 0x01 +#define SIMPAD_BATT_STATUS_LOW 0x02 +#define SIMPAD_BATT_STATUS_CRITICAL 0x04 +#define SIMPAD_BATT_STATUS_CHARGING 0x08 +#define SIMPAD_BATT_STATUS_CHARGE_MAIN 0x10 +#define SIMPAD_BATT_STATUS_DEAD 0x20 /* Battery will not charge */ +#define SIMPAD_BATT_NOT_INSTALLED 0x20 /* For expansion pack batteries */ +#define SIMPAD_BATT_STATUS_FULL 0x40 /* Battery fully charged (and connected to AC) */ +#define SIMPAD_BATT_STATUS_NOBATT 0x80 +#define SIMPAD_BATT_STATUS_UNKNOWN 0xff + +extern int simpad_get_battery(struct simpad_battery* ); + +#endif // __ASM_ARCH_SIMPAD_H + + + + + + + + |
