1 files changed, 375 insertions, 6 deletions

diff --git a/arch/arm/mach-s5pv210/mach-goni.c b/arch/arm/mach-s5pv210/mach-goni.c
index d9ecf57..b1dcf96 100644
--- a/arch/arm/mach-s5pv210/mach-goni.c
+++ b/arch/arm/mach-s5pv210/mach-goni.c
@@ -15,7 +15,13 @@
 #include <linux/fb.h>
 #include <linux/i2c.h>
 #include <linux/i2c-gpio.h>
+#include <linux/i2c/qt602240_ts.h>
 #include <linux/mfd/max8998.h>
+#include <linux/mfd/wm8994/pdata.h>
+#include <linux/regulator/fixed.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/spi_gpio.h>
+#include <linux/lcd.h>
 #include <linux/gpio_keys.h>
 #include <linux/input.h>
 #include <linux/gpio.h>
@@ -35,7 +41,10 @@
 #include <plat/devs.h>
 #include <plat/cpu.h>
 #include <plat/fb.h>
+#include <plat/iic.h>
+#include <plat/keypad.h>
 #include <plat/sdhci.h>
+#include <plat/clock.h>
 
 /* Following are default values for UCON, ULCON and UFCON UART registers */
 #define GONI_UCON_DEFAULT	(S3C2410_UCON_TXILEVEL |	\
@@ -87,13 +96,12 @@ static struct s3c2410_uartcfg goni_uartcfgs[] __initdata = {
 /* Frame Buffer */
 static struct s3c_fb_pd_win goni_fb_win0 = {
 	.win_mode = {
-		.pixclock = 1000000000000ULL / ((16+16+2+480)*(28+3+2+800)*55),
 		.left_margin	= 16,
 		.right_margin	= 16,
-		.upper_margin	= 3,
+		.upper_margin	= 2,
 		.lower_margin	= 28,
 		.hsync_len	= 2,
-		.vsync_len	= 2,
+		.vsync_len	= 1,
 		.xres		= 480,
 		.yres		= 800,
 		.refresh	= 55,
@@ -111,9 +119,160 @@ static struct s3c_fb_platdata goni_lcd_pdata __initdata = {
 	.setup_gpio	= s5pv210_fb_gpio_setup_24bpp,
 };
 
+static int lcd_power_on(struct lcd_device *ld, int enable)
+{
+	return 1;
+}
+
+static int reset_lcd(struct lcd_device *ld)
+{
+	static unsigned int first = 1;
+	int reset_gpio = -1;
+
+	reset_gpio = S5PV210_MP05(5);
+
+	if (first) {
+		gpio_request(reset_gpio, "MLCD_RST");
+		first = 0;
+	}
+
+	gpio_direction_output(reset_gpio, 1);
+	return 1;
+}
+
+static struct lcd_platform_data goni_lcd_platform_data = {
+	.reset			= reset_lcd,
+	.power_on		= lcd_power_on,
+	.lcd_enabled		= 0,
+	.reset_delay		= 120,	/* 120ms */
+	.power_on_delay		= 25,	/* 25ms */
+	.power_off_delay	= 200,	/* 200ms */
+};
+
+#define LCD_BUS_NUM	3
+static struct spi_board_info spi_board_info[] __initdata = {
+	{
+		.modalias	= "s6e63m0",
+		.platform_data	= &goni_lcd_platform_data,
+		.max_speed_hz	= 1200000,
+		.bus_num	= LCD_BUS_NUM,
+		.chip_select	= 0,
+		.mode		= SPI_MODE_3,
+		.controller_data = (void *)S5PV210_MP01(1), /* DISPLAY_CS */
+	},
+};
+
+static struct spi_gpio_platform_data lcd_spi_gpio_data = {
+	.sck	= S5PV210_MP04(1), /* DISPLAY_CLK */
+	.mosi	= S5PV210_MP04(3), /* DISPLAY_SI */
+	.miso	= SPI_GPIO_NO_MISO,
+	.num_chipselect	= 1,
+};
+
+static struct platform_device goni_spi_gpio = {
+	.name	= "spi_gpio",
+	.id	= LCD_BUS_NUM,
+	.dev	= {
+		.parent		= &s3c_device_fb.dev,
+		.platform_data	= &lcd_spi_gpio_data,
+	},
+};
+
+/* KEYPAD */
+static uint32_t keymap[] __initdata = {
+	/* KEY(row, col, keycode) */
+	KEY(0, 1, KEY_MENU),		/* Send */
+	KEY(0, 2, KEY_BACK),		/* End */
+	KEY(1, 1, KEY_CONFIG),		/* Half shot */
+	KEY(1, 2, KEY_VOLUMEUP),
+	KEY(2, 1, KEY_CAMERA),		/* Full shot */
+	KEY(2, 2, KEY_VOLUMEDOWN),
+};
+
+static struct matrix_keymap_data keymap_data __initdata = {
+	.keymap		= keymap,
+	.keymap_size	= ARRAY_SIZE(keymap),
+};
+
+static struct samsung_keypad_platdata keypad_data __initdata = {
+	.keymap_data	= &keymap_data,
+	.rows		= 3,
+	.cols		= 3,
+};
+
+/* Radio */
+static struct i2c_board_info i2c1_devs[] __initdata = {
+	{
+		I2C_BOARD_INFO("si470x", 0x10),
+	},
+};
+
+static void __init goni_radio_init(void)
+{
+	int gpio;
+
+	gpio = S5PV210_GPJ2(4);			/* XMSMDATA_4 */
+	gpio_request(gpio, "FM_INT");
+	s3c_gpio_cfgpin(gpio, S3C_GPIO_SFN(0xf));
+	i2c1_devs[0].irq = gpio_to_irq(gpio);
+
+	gpio = S5PV210_GPJ2(5);			/* XMSMDATA_5 */
+	gpio_request(gpio, "FM_RST");
+	gpio_direction_output(gpio, 1);
+}
+
+/* TSP */
+static struct qt602240_platform_data qt602240_platform_data = {
+	.x_line		= 17,
+	.y_line		= 11,
+	.x_size		= 800,
+	.y_size		= 480,
+	.blen		= 0x21,
+	.threshold	= 0x28,
+	.voltage	= 2800000,              /* 2.8V */
+	.orient		= QT602240_DIAGONAL,
+};
+
+static struct s3c2410_platform_i2c i2c2_data __initdata = {
+	.flags		= 0,
+	.bus_num	= 2,
+	.slave_addr	= 0x10,
+	.frequency	= 400 * 1000,
+	.sda_delay	= 100,
+};
+
+static struct i2c_board_info i2c2_devs[] __initdata = {
+	{
+		I2C_BOARD_INFO("qt602240_ts", 0x4a),
+		.platform_data = &qt602240_platform_data,
+	},
+};
+
+static void __init goni_tsp_init(void)
+{
+	int gpio;
+
+	gpio = S5PV210_GPJ1(3);		/* XMSMADDR_11 */
+	gpio_request(gpio, "TSP_LDO_ON");
+	gpio_direction_output(gpio, 1);
+	gpio_export(gpio, 0);
+
+	gpio = S5PV210_GPJ0(5);		/* XMSMADDR_5 */
+	gpio_request(gpio, "TSP_INT");
+
+	s5p_register_gpio_interrupt(gpio);
+	s3c_gpio_cfgpin(gpio, S3C_GPIO_SFN(0xf));
+	s3c_gpio_setpull(gpio, S3C_GPIO_PULL_UP);
+	i2c2_devs[0].irq = gpio_to_irq(gpio);
+}
+
 /* MAX8998 regulators */
 #if defined(CONFIG_REGULATOR_MAX8998) || defined(CONFIG_REGULATOR_MAX8998_MODULE)
 
+static struct regulator_consumer_supply goni_ldo5_consumers[] = {
+	REGULATOR_SUPPLY("vmmc", "s3c-sdhci.0"),
+};
+
 static struct regulator_init_data goni_ldo2_data = {
 	.constraints	= {
 		.name		= "VALIVE_1.1V",
@@ -153,6 +312,8 @@ static struct regulator_init_data goni_ldo5_data = {
 		.max_uV		= 2800000,
 		.apply_uV	= 1,
 	},
+	.num_consumer_supplies = ARRAY_SIZE(goni_ldo5_consumers),
+	.consumer_supplies = goni_ldo5_consumers,
 };
 
 static struct regulator_init_data goni_ldo6_data = {
@@ -360,6 +521,119 @@ static struct max8998_platform_data goni_max8998_pdata = {
 };
 #endif
 
+static struct regulator_consumer_supply wm8994_fixed_voltage0_supplies[] = {
+	{
+		.dev_name	= "5-001a",
+		.supply		= "DBVDD",
+	}, {
+		.dev_name	= "5-001a",
+		.supply		= "AVDD2",
+	}, {
+		.dev_name	= "5-001a",
+		.supply		= "CPVDD",
+	},
+};
+
+static struct regulator_consumer_supply wm8994_fixed_voltage1_supplies[] = {
+	{
+		.dev_name	= "5-001a",
+		.supply		= "SPKVDD1",
+	}, {
+		.dev_name	= "5-001a",
+		.supply		= "SPKVDD2",
+	},
+};
+
+static struct regulator_init_data wm8994_fixed_voltage0_init_data = {
+	.constraints = {
+		.always_on = 1,
+	},
+	.num_consumer_supplies	= ARRAY_SIZE(wm8994_fixed_voltage0_supplies),
+	.consumer_supplies	= wm8994_fixed_voltage0_supplies,
+};
+
+static struct regulator_init_data wm8994_fixed_voltage1_init_data = {
+	.constraints = {
+		.always_on = 1,
+	},
+	.num_consumer_supplies	= ARRAY_SIZE(wm8994_fixed_voltage1_supplies),
+	.consumer_supplies	= wm8994_fixed_voltage1_supplies,
+};
+
+static struct fixed_voltage_config wm8994_fixed_voltage0_config = {
+	.supply_name	= "VCC_1.8V_PDA",
+	.microvolts	= 1800000,
+	.gpio		= -EINVAL,
+	.init_data	= &wm8994_fixed_voltage0_init_data,
+};
+
+static struct fixed_voltage_config wm8994_fixed_voltage1_config = {
+	.supply_name	= "V_BAT",
+	.microvolts	= 3700000,
+	.gpio		= -EINVAL,
+	.init_data	= &wm8994_fixed_voltage1_init_data,
+};
+
+static struct platform_device wm8994_fixed_voltage0 = {
+	.name		= "reg-fixed-voltage",
+	.id		= 0,
+	.dev		= {
+		.platform_data	= &wm8994_fixed_voltage0_config,
+	},
+};
+
+static struct platform_device wm8994_fixed_voltage1 = {
+	.name		= "reg-fixed-voltage",
+	.id		= 1,
+	.dev		= {
+		.platform_data	= &wm8994_fixed_voltage1_config,
+	},
+};
+
+static struct regulator_consumer_supply wm8994_avdd1_supply = {
+	.dev_name	= "5-001a",
+	.supply		= "AVDD1",
+};
+
+static struct regulator_consumer_supply wm8994_dcvdd_supply = {
+	.dev_name	= "5-001a",
+	.supply		= "DCVDD",
+};
+
+static struct regulator_init_data wm8994_ldo1_data = {
+	.constraints	= {
+		.name		= "AVDD1_3.0V",
+		.valid_ops_mask	= REGULATOR_CHANGE_STATUS,
+	},
+	.num_consumer_supplies	= 1,
+	.consumer_supplies	= &wm8994_avdd1_supply,
+};
+
+static struct regulator_init_data wm8994_ldo2_data = {
+	.constraints	= {
+		.name		= "DCVDD_1.0V",
+	},
+	.num_consumer_supplies	= 1,
+	.consumer_supplies	= &wm8994_dcvdd_supply,
+};
+
+static struct wm8994_pdata wm8994_platform_data = {
+	/* configure gpio1 function: 0x0001(Logic level input/output) */
+	.gpio_defaults[0] = 0x0001,
+	/* configure gpio3/4/5/7 function for AIF2 voice */
+	.gpio_defaults[2] = 0x8100,
+	.gpio_defaults[3] = 0x8100,
+	.gpio_defaults[4] = 0x8100,
+	.gpio_defaults[6] = 0x0100,
+	/* configure gpio8/9/10/11 function for AIF3 BT */
+	.gpio_defaults[7] = 0x8100,
+	.gpio_defaults[8] = 0x0100,
+	.gpio_defaults[9] = 0x0100,
+	.gpio_defaults[10] = 0x0100,
+	.ldo[0]	= { S5PV210_MP03(6), NULL, &wm8994_ldo1_data },	/* XM0FRNB_2 */
+	.ldo[1]	= { 0, NULL, &wm8994_ldo2_data },
+};
+
 /* GPIO I2C PMIC */
 #define AP_I2C_GPIO_PMIC_BUS_4	4
 static struct i2c_gpio_platform_data goni_i2c_gpio_pmic_data = {
@@ -385,6 +659,29 @@ static struct i2c_board_info i2c_gpio_pmic_devs[] __initdata = {
 #endif
 };
 
+/* GPIO I2C AP 1.8V */
+#define AP_I2C_GPIO_BUS_5	5
+static struct i2c_gpio_platform_data goni_i2c_gpio5_data = {
+	.sda_pin	= S5PV210_MP05(3),	/* XM0ADDR_11 */
+	.scl_pin	= S5PV210_MP05(2),	/* XM0ADDR_10 */
+};
+
+static struct platform_device goni_i2c_gpio5 = {
+	.name		= "i2c-gpio",
+	.id		= AP_I2C_GPIO_BUS_5,
+	.dev		= {
+		.platform_data	= &goni_i2c_gpio5_data,
+	},
+};
+
+static struct i2c_board_info i2c_gpio5_devs[] __initdata = {
+	{
+		/* CS/ADDR = low 0x34 (FYI: high = 0x36) */
+		I2C_BOARD_INFO("wm8994", 0x1a),
+		.platform_data	= &wm8994_platform_data,
+	},
+};
+
 /* PMIC Power button */
 static struct gpio_keys_button goni_gpio_keys_table[] = {
 	{
@@ -444,11 +741,37 @@ static struct s3c_sdhci_platdata goni_hsmmc2_data __initdata = {
 	.ext_cd_gpio_invert	= 1,
 };
 
+static struct regulator_consumer_supply mmc2_supplies[] = {
+	REGULATOR_SUPPLY("vmmc", "s3c-sdhci.2"),
+};
+
+static struct regulator_init_data mmc2_fixed_voltage_init_data = {
+	.constraints		= {
+		.name		= "V_TF_2.8V",
+		.valid_ops_mask	= REGULATOR_CHANGE_STATUS,
+	},
+	.num_consumer_supplies	= ARRAY_SIZE(mmc2_supplies),
+	.consumer_supplies	= mmc2_supplies,
+};
+
+static struct fixed_voltage_config mmc2_fixed_voltage_config = {
+	.supply_name		= "EXT_FLASH_EN",
+	.microvolts		= 2800000,
+	.gpio			= GONI_EXT_FLASH_EN,
+	.enable_high		= true,
+	.init_data		= &mmc2_fixed_voltage_init_data,
+};
+
+static struct platform_device mmc2_fixed_voltage = {
+	.name		= "reg-fixed-voltage",
+	.id		= 2,
+	.dev		= {
+		.platform_data	= &mmc2_fixed_voltage_config,
+	},
+};
+
 static void goni_setup_sdhci(void)
 {
-	gpio_request(GONI_EXT_FLASH_EN, "FLASH_EN");
-	gpio_direction_output(GONI_EXT_FLASH_EN, 1);
-
 	s3c_sdhci0_set_platdata(&goni_hsmmc0_data);
 	s3c_sdhci1_set_platdata(&goni_hsmmc1_data);
 	s3c_sdhci2_set_platdata(&goni_hsmmc2_data);
@@ -457,7 +780,10 @@ static void goni_setup_sdhci(void)
 static struct platform_device *goni_devices[] __initdata = {
 	&s3c_device_fb,
 	&s5p_device_onenand,
+	&goni_spi_gpio,
 	&goni_i2c_gpio_pmic,
+	&goni_i2c_gpio5,
+	&mmc2_fixed_voltage,
 	&goni_device_gpiokeys,
 	&s5p_device_fimc0,
 	&s5p_device_fimc1,
@@ -465,8 +791,24 @@ static struct platform_device *goni_devices[] __initdata = {
 	&s3c_device_hsmmc0,
 	&s3c_device_hsmmc1,
 	&s3c_device_hsmmc2,
+	&s5pv210_device_iis0,
+	&s3c_device_usb_hsotg,
+	&samsung_device_keypad,
+	&s3c_device_i2c1,
+	&s3c_device_i2c2,
+	&wm8994_fixed_voltage0,
+	&wm8994_fixed_voltage1,
 };
 
+static void __init goni_sound_init(void)
+{
+	/* Ths main clock of WM8994 codec uses the output of CLKOUT pin.
+	 * The CLKOUT[9:8] set to 0x3(XUSBXTI) of 0xE010E000(OTHERS)
+	 * because it needs 24MHz clock to operate WM8994 codec.
+	 */
+	__raw_writel(__raw_readl(S5P_OTHERS) | (0x3 << 8), S5P_OTHERS);
+}
+
 static void __init goni_map_io(void)
 {
 	s5p_init_io(NULL, 0, S5P_VA_CHIPID);
@@ -476,6 +818,20 @@ static void __init goni_map_io(void)
 
 static void __init goni_machine_init(void)
 {
+	/* Radio: call before I2C 1 registeration */
+	goni_radio_init();
+
+	/* I2C1 */
+	s3c_i2c1_set_platdata(NULL);
+	i2c_register_board_info(1, i2c1_devs, ARRAY_SIZE(i2c1_devs));
+
+	/* TSP: call before I2C 2 registeration */
+	goni_tsp_init();
+
+	/* I2C2 */
+	s3c_i2c2_set_platdata(&i2c2_data);
+	i2c_register_board_info(2, i2c2_devs, ARRAY_SIZE(i2c2_devs));
+
 	/* PMIC */
 	goni_pmic_init();
 	i2c_register_board_info(AP_I2C_GPIO_PMIC_BUS_4, i2c_gpio_pmic_devs,
@@ -483,9 +839,22 @@ static void __init goni_machine_init(void)
 	/* SDHCI */
 	goni_setup_sdhci();
 
+	/* SOUND */
+	goni_sound_init();
+	i2c_register_board_info(AP_I2C_GPIO_BUS_5, i2c_gpio5_devs,
+			ARRAY_SIZE(i2c_gpio5_devs));
+
 	/* FB */
 	s3c_fb_set_platdata(&goni_lcd_pdata);
 
+	/* SPI */
+	spi_register_board_info(spi_board_info, ARRAY_SIZE(spi_board_info));
+
+	/* KEYPAD */
+	samsung_keypad_set_platdata(&keypad_data);
+
+	clk_xusbxti.rate = 24000000;
+
 	platform_add_devices(goni_devices, ARRAY_SIZE(goni_devices));
 }