1 files changed, 83 insertions, 1 deletions

diff --git a/arch/arm/mach-omap2/vc.c b/arch/arm/mach-omap2/vc.c
index 49ac797..705eb35 100644
--- a/arch/arm/mach-omap2/vc.c
+++ b/arch/arm/mach-omap2/vc.c
@@ -220,6 +220,87 @@ static inline u32 omap_usec_to_32k(u32 usec)
 	return DIV_ROUND_UP_ULL(32768ULL * (u64)usec, 1000000ULL);
 }
 
+struct omap3_vc {
+	struct voltagedomain *vd;
+	u32 voltctrl;
+};
+static struct omap3_vc vc;
+
+void omap3_vc_set_pmic_signaling(int core_next_state)
+{
+	struct voltagedomain *vd = vc.vd;
+	u32 voltctrl;
+
+	voltctrl = vc.voltctrl;
+	switch (core_next_state) {
+	case PWRDM_POWER_OFF:
+		voltctrl &= ~(OMAP3430_PRM_VOLTCTRL_AUTO_RET |
+			      OMAP3430_PRM_VOLTCTRL_AUTO_SLEEP);
+		voltctrl |= OMAP3430_PRM_VOLTCTRL_AUTO_OFF;
+		break;
+	case PWRDM_POWER_RET:
+	default:
+		voltctrl &= ~(OMAP3430_PRM_VOLTCTRL_AUTO_OFF |
+			      OMAP3430_PRM_VOLTCTRL_AUTO_SLEEP);
+		voltctrl |= OMAP3430_PRM_VOLTCTRL_AUTO_RET;
+		break;
+	}
+	if (voltctrl != vc.voltctrl) {
+		vd->write(voltctrl, OMAP3_PRM_VOLTCTRL_OFFSET);
+		vc.voltctrl = voltctrl;
+	}
+}
+
+#define PRM_POLCTRL_TWL_MASK	(OMAP3430_PRM_POLCTRL_CLKREQ_POL | \
+					OMAP3430_PRM_POLCTRL_CLKREQ_POL)
+#define PRM_POLCTRL_TWL_VAL	OMAP3430_PRM_POLCTRL_CLKREQ_POL
+
+/*
+ * Configure signal polarity for sys_clkreq and sys_off_mode pins
+ * as the default values are wrong and can cause the system to hang
+ * if any twl4030 scripts are loaded.
+ */
+static void __init omap3_vc_init_pmic_signaling(struct voltagedomain *voltdm)
+{
+	u32 val;
+
+	if (vc.vd)
+		return;
+
+	vc.vd = voltdm;
+
+	val = voltdm->read(OMAP3_PRM_POLCTRL_OFFSET);
+	if (!(val & OMAP3430_PRM_POLCTRL_CLKREQ_POL) ||
+	    (val & OMAP3430_PRM_POLCTRL_CLKREQ_POL)) {
+		val |= OMAP3430_PRM_POLCTRL_CLKREQ_POL;
+		val &= ~OMAP3430_PRM_POLCTRL_OFFMODE_POL;
+		pr_debug("PM: fixing sys_clkreq and sys_off_mode polarity to 0x%x\n",
+			 val);
+		voltdm->write(val, OMAP3_PRM_POLCTRL_OFFSET);
+	}
+
+	/*
+	 * By default let's use I2C4 signaling for retention idle
+	 * and sys_off_mode pin signaling for off idle. This way we
+	 * have sys_clk_req pin go down for retention and both
+	 * sys_clk_req and sys_off_mode pins will go down for off
+	 * idle. And we can also scale voltages to zero for off-idle.
+	 * Note that no actual voltage scaling during off-idle will
+	 * happen unless the board specific twl4030 PMIC scripts are
+	 * loaded.
+	 */
+	val = voltdm->read(OMAP3_PRM_VOLTCTRL_OFFSET);
+	if (!(val & OMAP3430_PRM_VOLTCTRL_SEL_OFF)) {
+		val |= OMAP3430_PRM_VOLTCTRL_SEL_OFF;
+		pr_debug("PM: setting voltctrl sys_off_mode signaling to 0x%x\n",
+			 val);
+		voltdm->write(val, OMAP3_PRM_VOLTCTRL_OFFSET);
+	}
+	vc.voltctrl = val;
+
+	omap3_vc_set_pmic_signaling(PWRDM_POWER_ON);
+}
+
 /* Set oscillator setup time for omap3 */
 static void omap3_set_clksetup(u32 usec, struct voltagedomain *voltdm)
 {
@@ -292,7 +373,7 @@ static void omap3_set_off_timings(struct voltagedomain *voltdm)
 
 	/* check if sys_off_mode is used to control off-mode voltages */
 	val = voltdm->read(OMAP3_PRM_VOLTCTRL_OFFSET);
-	if (!(val & OMAP3430_SEL_OFF_MASK)) {
+	if (!(val & OMAP3430_PRM_VOLTCTRL_SEL_OFF)) {
 		/* No, omap is controlling them over I2C */
 		omap3_set_i2c_timings(voltdm, true);
 		return;
@@ -337,6 +418,7 @@ static void omap3_set_off_timings(struct voltagedomain *voltdm)
 
 static void __init omap3_vc_init_channel(struct voltagedomain *voltdm)
 {
+	omap3_vc_init_pmic_signaling(voltdm);
 	omap3_set_off_timings(voltdm);
 }