diff options
Diffstat (limited to 'arch/arm/mach-omap2/opp2420_data.c')
| -rw-r--r-- | arch/arm/mach-omap2/opp2420_data.c | 38 |
1 files changed, 20 insertions, 18 deletions
diff --git a/arch/arm/mach-omap2/opp2420_data.c b/arch/arm/mach-omap2/opp2420_data.c index 126a9396..e6dda69 100644 --- a/arch/arm/mach-omap2/opp2420_data.c +++ b/arch/arm/mach-omap2/opp2420_data.c @@ -9,45 +9,47 @@ * The OMAP2 processor can be run at several discrete 'PRCM configurations'. * These configurations are characterized by voltage and speed for clocks. * The device is only validated for certain combinations. One way to express - * these combinations is via the 'ratio's' which the clocks operate with + * these combinations is via the 'ratios' which the clocks operate with * respect to each other. These ratio sets are for a given voltage/DPLL - * setting. All configurations can be described by a DPLL setting and a ratio - * There are 3 ratio sets for the 2430 and X ratio sets for 2420. - * - * 2430 differs from 2420 in that there are no more phase synchronizers used. - * They both have a slightly different clock domain setup. 2420(iva1,dsp) vs - * 2430 (iva2.1, NOdsp, mdm) + * setting. All configurations can be described by a DPLL setting and a ratio. * * XXX Missing voltage data. + * XXX Missing 19.2MHz sys_clk rate sets (needed for N800/N810) * * THe format described in this file is deprecated. Once a reasonable * OPP API exists, the data in this file should be converted to use it. * * This is technically part of the OMAP2xxx clock code. + * + * Considerable work is still needed to fully support dynamic frequency + * changes on OMAP2xxx-series chips. Readers interested in such a + * project are encouraged to review the Maemo Diablo RX-34 and RX-44 + * kernel source at: + * http://repository.maemo.org/pool/diablo/free/k/kernel-source-diablo/ */ #include "opp2xxx.h" #include "sdrc.h" #include "clock.h" -/*------------------------------------------------------------------------- - * Key dividers which make up a PRCM set. Ratio's for a PRCM are mandated. +/* + * Key dividers which make up a PRCM set. Ratios for a PRCM are mandated. * xtal_speed, dpll_speed, mpu_speed, CM_CLKSEL_MPU, * CM_CLKSEL_DSP, CM_CLKSEL_GFX, CM_CLKSEL1_CORE, CM_CLKSEL1_PLL, * CM_CLKSEL2_PLL, CM_CLKSEL_MDM * - * Filling in table based on H4 boards and 2430-SDPs variants available. - * There are quite a few more rates combinations which could be defined. + * Filling in table based on H4 boards available. There are quite a + * few more rate combinations which could be defined. * - * When multiple values are defined the start up will try and choose the - * fastest one. If a 'fast' value is defined, then automatically, the /2 - * one should be included as it can be used. Generally having more that - * one fast set does not make sense, as static timings need to be changed - * to change the set. The exception is the bypass setting which is - * availble for low power bypass. + * When multiple values are defined the start up will try and choose + * the fastest one. If a 'fast' value is defined, then automatically, + * the /2 one should be included as it can be used. Generally having + * more than one fast set does not make sense, as static timings need + * to be changed to change the set. The exception is the bypass + * setting which is available for low power bypass. * * Note: This table needs to be sorted, fastest to slowest. - *-------------------------------------------------------------------------*/ + **/ const struct prcm_config omap2420_rate_table[] = { /* PRCM I - FAST */ {S12M, S660M, S330M, RI_CM_CLKSEL_MPU_VAL, /* 330MHz ARM */ |
