diff options
Diffstat (limited to 'arch/arm/mach-omap2/board-omap3evm.c')
| -rw-r--r-- | arch/arm/mach-omap2/board-omap3evm.c | 756 |
1 files changed, 0 insertions, 756 deletions
diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c deleted file mode 100644 index 1814387..0000000 --- a/arch/arm/mach-omap2/board-omap3evm.c +++ /dev/null @@ -1,756 +0,0 @@ -/* - * linux/arch/arm/mach-omap2/board-omap3evm.c - * - * Copyright (C) 2008 Texas Instruments - * - * Modified from mach-omap2/board-3430sdp.c - * - * Initial code: Syed Mohammed Khasim - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ - -#include <linux/kernel.h> -#include <linux/init.h> -#include <linux/platform_device.h> -#include <linux/delay.h> -#include <linux/err.h> -#include <linux/clk.h> -#include <linux/gpio.h> -#include <linux/input.h> -#include <linux/input/matrix_keypad.h> -#include <linux/leds.h> -#include <linux/interrupt.h> - -#include <linux/mtd/mtd.h> -#include <linux/mtd/partitions.h> -#include <linux/mtd/nand.h> - -#include <linux/spi/spi.h> -#include <linux/spi/ads7846.h> -#include <linux/i2c/twl.h> -#include <linux/usb/otg.h> -#include <linux/usb/musb.h> -#include <linux/usb/usb_phy_gen_xceiv.h> -#include <linux/smsc911x.h> - -#include <linux/wl12xx.h> -#include <linux/regulator/fixed.h> -#include <linux/regulator/machine.h> -#include <linux/mmc/host.h> -#include <linux/export.h> -#include <linux/usb/phy.h> - -#include <asm/mach-types.h> -#include <asm/mach/arch.h> -#include <asm/mach/map.h> - -#include <linux/platform_data/mtd-nand-omap2.h> -#include "common.h" -#include <linux/platform_data/spi-omap2-mcspi.h> -#include <video/omapdss.h> -#include <video/omap-panel-data.h> - -#include "soc.h" -#include "mux.h" -#include "sdram-micron-mt46h32m32lf-6.h" -#include "hsmmc.h" -#include "common-board-devices.h" -#include "board-flash.h" - -#define NAND_CS 0 - -#define OMAP3_EVM_TS_GPIO 175 -#define OMAP3_EVM_EHCI_VBUS 22 -#define OMAP3_EVM_EHCI_SELECT 61 - -#define OMAP3EVM_ETHR_START 0x2c000000 -#define OMAP3EVM_ETHR_SIZE 1024 -#define OMAP3EVM_ETHR_ID_REV 0x50 -#define OMAP3EVM_ETHR_GPIO_IRQ 176 -#define OMAP3EVM_SMSC911X_CS 5 -/* - * Eth Reset signal - * 64 = Generation 1 (<=RevD) - * 7 = Generation 2 (>=RevE) - */ -#define OMAP3EVM_GEN1_ETHR_GPIO_RST 64 -#define OMAP3EVM_GEN2_ETHR_GPIO_RST 7 - -/* - * OMAP35x EVM revision - * Run time detection of EVM revision is done by reading Ethernet - * PHY ID - - * GEN_1 = 0x01150000 - * GEN_2 = 0x92200000 - */ -enum { - OMAP3EVM_BOARD_GEN_1 = 0, /* EVM Rev between A - D */ - OMAP3EVM_BOARD_GEN_2, /* EVM Rev >= Rev E */ -}; - -static u8 omap3_evm_version; - -static u8 get_omap3_evm_rev(void) -{ - return omap3_evm_version; -} - -static void __init omap3_evm_get_revision(void) -{ - void __iomem *ioaddr; - unsigned int smsc_id; - - /* Ethernet PHY ID is stored at ID_REV register */ - ioaddr = ioremap_nocache(OMAP3EVM_ETHR_START, SZ_1K); - if (!ioaddr) - return; - smsc_id = readl(ioaddr + OMAP3EVM_ETHR_ID_REV) & 0xFFFF0000; - iounmap(ioaddr); - - switch (smsc_id) { - /*SMSC9115 chipset*/ - case 0x01150000: - omap3_evm_version = OMAP3EVM_BOARD_GEN_1; - break; - /*SMSC 9220 chipset*/ - case 0x92200000: - default: - omap3_evm_version = OMAP3EVM_BOARD_GEN_2; - } -} - -#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE) -#include "gpmc-smsc911x.h" - -static struct omap_smsc911x_platform_data smsc911x_cfg = { - .cs = OMAP3EVM_SMSC911X_CS, - .gpio_irq = OMAP3EVM_ETHR_GPIO_IRQ, - .gpio_reset = -EINVAL, - .flags = SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS, -}; - -static inline void __init omap3evm_init_smsc911x(void) -{ - /* Configure ethernet controller reset gpio */ - if (cpu_is_omap3430()) { - if (get_omap3_evm_rev() == OMAP3EVM_BOARD_GEN_1) - smsc911x_cfg.gpio_reset = OMAP3EVM_GEN1_ETHR_GPIO_RST; - else - smsc911x_cfg.gpio_reset = OMAP3EVM_GEN2_ETHR_GPIO_RST; - } - - gpmc_smsc911x_init(&smsc911x_cfg); -} - -#else -static inline void __init omap3evm_init_smsc911x(void) { return; } -#endif - -/* - * OMAP3EVM LCD Panel control signals - */ -#define OMAP3EVM_LCD_PANEL_LR 2 -#define OMAP3EVM_LCD_PANEL_UD 3 -#define OMAP3EVM_LCD_PANEL_INI 152 -#define OMAP3EVM_LCD_PANEL_QVGA 154 -#define OMAP3EVM_LCD_PANEL_RESB 155 - -#define OMAP3EVM_LCD_PANEL_ENVDD 153 -#define OMAP3EVM_LCD_PANEL_BKLIGHT_GPIO 210 - -/* - * OMAP3EVM DVI control signals - */ -#define OMAP3EVM_DVI_PANEL_EN_GPIO 199 - -#ifdef CONFIG_BROKEN -static void __init omap3_evm_display_init(void) -{ - int r; - - r = gpio_request_one(OMAP3EVM_LCD_PANEL_ENVDD, GPIOF_OUT_INIT_LOW, - "lcd_panel_envdd"); - if (r) - pr_err("failed to get lcd_panel_envdd GPIO\n"); - - r = gpio_request_one(OMAP3EVM_LCD_PANEL_BKLIGHT_GPIO, - GPIOF_OUT_INIT_LOW, "lcd_panel_bklight"); - if (r) - pr_err("failed to get lcd_panel_bklight GPIO\n"); - - if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2) - gpio_set_value_cansleep(OMAP3EVM_LCD_PANEL_BKLIGHT_GPIO, 0); - else - gpio_set_value_cansleep(OMAP3EVM_LCD_PANEL_BKLIGHT_GPIO, 1); -} -#endif - -static struct panel_sharp_ls037v7dw01_platform_data omap3_evm_lcd_pdata = { - .name = "lcd", - .source = "dpi.0", - - .data_lines = 18, - - .resb_gpio = OMAP3EVM_LCD_PANEL_RESB, - .ini_gpio = OMAP3EVM_LCD_PANEL_INI, - .mo_gpio = OMAP3EVM_LCD_PANEL_QVGA, - .lr_gpio = OMAP3EVM_LCD_PANEL_LR, - .ud_gpio = OMAP3EVM_LCD_PANEL_UD, -}; - -static struct platform_device omap3_evm_lcd_device = { - .name = "panel-sharp-ls037v7dw01", - .id = 0, - .dev.platform_data = &omap3_evm_lcd_pdata, -}; - -static struct connector_dvi_platform_data omap3_evm_dvi_connector_pdata = { - .name = "dvi", - .source = "tfp410.0", - .i2c_bus_num = -1, -}; - -static struct platform_device omap3_evm_dvi_connector_device = { - .name = "connector-dvi", - .id = 0, - .dev.platform_data = &omap3_evm_dvi_connector_pdata, -}; - -static struct encoder_tfp410_platform_data omap3_evm_tfp410_pdata = { - .name = "tfp410.0", - .source = "dpi.0", - .data_lines = 24, - .power_down_gpio = OMAP3EVM_DVI_PANEL_EN_GPIO, -}; - -static struct platform_device omap3_evm_tfp410_device = { - .name = "tfp410", - .id = 0, - .dev.platform_data = &omap3_evm_tfp410_pdata, -}; - -static struct connector_atv_platform_data omap3_evm_tv_pdata = { - .name = "tv", - .source = "venc.0", - .connector_type = OMAP_DSS_VENC_TYPE_SVIDEO, - .invert_polarity = false, -}; - -static struct platform_device omap3_evm_tv_connector_device = { - .name = "connector-analog-tv", - .id = 0, - .dev.platform_data = &omap3_evm_tv_pdata, -}; - -static struct omap_dss_board_info omap3_evm_dss_data = { - .default_display_name = "lcd", -}; - -static struct regulator_consumer_supply omap3evm_vmmc1_supply[] = { - REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"), -}; - -static struct regulator_consumer_supply omap3evm_vsim_supply[] = { - REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.0"), -}; - -/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */ -static struct regulator_init_data omap3evm_vmmc1 = { - .constraints = { - .min_uV = 1850000, - .max_uV = 3150000, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE - | REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = ARRAY_SIZE(omap3evm_vmmc1_supply), - .consumer_supplies = omap3evm_vmmc1_supply, -}; - -/* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */ -static struct regulator_init_data omap3evm_vsim = { - .constraints = { - .min_uV = 1800000, - .max_uV = 3000000, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE - | REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = ARRAY_SIZE(omap3evm_vsim_supply), - .consumer_supplies = omap3evm_vsim_supply, -}; - -static struct omap2_hsmmc_info mmc[] = { - { - .mmc = 1, - .caps = MMC_CAP_4_BIT_DATA, - .gpio_cd = -EINVAL, - .gpio_wp = 63, - .deferred = true, - }, -#ifdef CONFIG_WILINK_PLATFORM_DATA - { - .name = "wl1271", - .mmc = 2, - .caps = MMC_CAP_4_BIT_DATA | MMC_CAP_POWER_OFF_CARD, - .gpio_wp = -EINVAL, - .gpio_cd = -EINVAL, - .nonremovable = true, - }, -#endif - {} /* Terminator */ -}; - -static struct gpio_led gpio_leds[] = { - { - .name = "omap3evm::ledb", - /* normally not visible (board underside) */ - .default_trigger = "default-on", - .gpio = -EINVAL, /* gets replaced */ - .active_low = true, - }, -}; - -static struct gpio_led_platform_data gpio_led_info = { - .leds = gpio_leds, - .num_leds = ARRAY_SIZE(gpio_leds), -}; - -static struct platform_device leds_gpio = { - .name = "leds-gpio", - .id = -1, - .dev = { - .platform_data = &gpio_led_info, - }, -}; - - -static int omap3evm_twl_gpio_setup(struct device *dev, - unsigned gpio, unsigned ngpio) -{ - int r, lcd_bl_en; - - /* gpio + 0 is "mmc0_cd" (input/IRQ) */ - mmc[0].gpio_cd = gpio + 0; - omap_hsmmc_late_init(mmc); - - /* - * Most GPIOs are for USB OTG. Some are mostly sent to - * the P2 connector; notably LEDA for the LCD backlight. - */ - - /* TWL4030_GPIO_MAX + 0 == ledA, LCD Backlight control */ - lcd_bl_en = get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2 ? - GPIOF_OUT_INIT_HIGH : GPIOF_OUT_INIT_LOW; - r = gpio_request_one(gpio + TWL4030_GPIO_MAX, lcd_bl_en, "EN_LCD_BKL"); - if (r) - printk(KERN_ERR "failed to get/set lcd_bkl gpio\n"); - - /* gpio + 7 == DVI Enable */ - gpio_request_one(gpio + 7, GPIOF_OUT_INIT_LOW, "EN_DVI"); - - /* TWL4030_GPIO_MAX + 1 == ledB (out, active low LED) */ - gpio_leds[0].gpio = gpio + TWL4030_GPIO_MAX + 1; - - platform_device_register(&leds_gpio); - - /* Enable VBUS switch by setting TWL4030.GPIO2DIR as output - * for starting USB tranceiver - */ -#ifdef CONFIG_TWL4030_CORE - if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2) { - u8 val; - - twl_i2c_read_u8(TWL4030_MODULE_GPIO, &val, REG_GPIODATADIR1); - val |= 0x04; /* TWL4030.GPIO2DIR BIT at GPIODATADIR1(0x9B) */ - twl_i2c_write_u8(TWL4030_MODULE_GPIO, val, REG_GPIODATADIR1); - } -#endif - - return 0; -} - -static struct twl4030_gpio_platform_data omap3evm_gpio_data = { - .use_leds = true, - .setup = omap3evm_twl_gpio_setup, -}; - -static uint32_t board_keymap[] = { - KEY(0, 0, KEY_LEFT), - KEY(0, 1, KEY_DOWN), - KEY(0, 2, KEY_ENTER), - KEY(0, 3, KEY_M), - - KEY(1, 0, KEY_RIGHT), - KEY(1, 1, KEY_UP), - KEY(1, 2, KEY_I), - KEY(1, 3, KEY_N), - - KEY(2, 0, KEY_A), - KEY(2, 1, KEY_E), - KEY(2, 2, KEY_J), - KEY(2, 3, KEY_O), - - KEY(3, 0, KEY_B), - KEY(3, 1, KEY_F), - KEY(3, 2, KEY_K), - KEY(3, 3, KEY_P) -}; - -static struct matrix_keymap_data board_map_data = { - .keymap = board_keymap, - .keymap_size = ARRAY_SIZE(board_keymap), -}; - -static struct twl4030_keypad_data omap3evm_kp_data = { - .keymap_data = &board_map_data, - .rows = 4, - .cols = 4, - .rep = 1, -}; - -/* ads7846 on SPI */ -static struct regulator_consumer_supply omap3evm_vio_supply[] = { - REGULATOR_SUPPLY("vcc", "spi1.0"), -}; - -/* VIO for ads7846 */ -static struct regulator_init_data omap3evm_vio = { - .constraints = { - .min_uV = 1800000, - .max_uV = 1800000, - .apply_uV = true, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = ARRAY_SIZE(omap3evm_vio_supply), - .consumer_supplies = omap3evm_vio_supply, -}; - -#ifdef CONFIG_WILINK_PLATFORM_DATA - -#define OMAP3EVM_WLAN_PMENA_GPIO (150) -#define OMAP3EVM_WLAN_IRQ_GPIO (149) - -static struct regulator_consumer_supply omap3evm_vmmc2_supply[] = { - REGULATOR_SUPPLY("vmmc", "omap_hsmmc.1"), -}; - -/* VMMC2 for driving the WL12xx module */ -static struct regulator_init_data omap3evm_vmmc2 = { - .constraints = { - .valid_ops_mask = REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = ARRAY_SIZE(omap3evm_vmmc2_supply), - .consumer_supplies = omap3evm_vmmc2_supply, -}; - -static struct fixed_voltage_config omap3evm_vwlan = { - .supply_name = "vwl1271", - .microvolts = 1800000, /* 1.80V */ - .gpio = OMAP3EVM_WLAN_PMENA_GPIO, - .startup_delay = 70000, /* 70ms */ - .enable_high = 1, - .enabled_at_boot = 0, - .init_data = &omap3evm_vmmc2, -}; - -static struct platform_device omap3evm_wlan_regulator = { - .name = "reg-fixed-voltage", - .id = 1, - .dev = { - .platform_data = &omap3evm_vwlan, - }, -}; - -struct wl12xx_platform_data omap3evm_wlan_data __initdata = { - .board_ref_clock = WL12XX_REFCLOCK_38, /* 38.4 MHz */ -}; -#endif - -/* VAUX2 for USB */ -static struct regulator_consumer_supply omap3evm_vaux2_supplies[] = { - REGULATOR_SUPPLY("VDD_CSIPHY1", "omap3isp"), /* OMAP ISP */ - REGULATOR_SUPPLY("VDD_CSIPHY2", "omap3isp"), /* OMAP ISP */ - REGULATOR_SUPPLY("vcc", "usb_phy_gen_xceiv.2"), /* hsusb port 2 */ - REGULATOR_SUPPLY("vaux2", NULL), -}; - -static struct regulator_init_data omap3evm_vaux2 = { - .constraints = { - .min_uV = 2800000, - .max_uV = 2800000, - .apply_uV = true, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = ARRAY_SIZE(omap3evm_vaux2_supplies), - .consumer_supplies = omap3evm_vaux2_supplies, -}; - -static struct twl4030_platform_data omap3evm_twldata = { - /* platform_data for children goes here */ - .keypad = &omap3evm_kp_data, - .gpio = &omap3evm_gpio_data, - .vio = &omap3evm_vio, - .vmmc1 = &omap3evm_vmmc1, - .vsim = &omap3evm_vsim, -}; - -static int __init omap3_evm_i2c_init(void) -{ - omap3_pmic_get_config(&omap3evm_twldata, - TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_MADC | - TWL_COMMON_PDATA_AUDIO, - TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2); - - omap3evm_twldata.vdac->constraints.apply_uV = true; - omap3evm_twldata.vpll2->constraints.apply_uV = true; - - omap3_pmic_init("twl4030", &omap3evm_twldata); - omap_register_i2c_bus(2, 400, NULL, 0); - omap_register_i2c_bus(3, 400, NULL, 0); - return 0; -} - -static struct usbhs_phy_data phy_data[] __initdata = { - { - .port = 2, - .reset_gpio = -1, /* set at runtime */ - .vcc_gpio = -EINVAL, - }, -}; - -static struct usbhs_omap_platform_data usbhs_bdata __initdata = { - .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, -}; - -#ifdef CONFIG_OMAP_MUX -static struct omap_board_mux omap35x_board_mux[] __initdata = { - OMAP3_MUX(SYS_NIRQ, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP | - OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_OUTPUT_LOW | - OMAP_PIN_OFF_WAKEUPENABLE), - OMAP3_MUX(MCSPI1_CS1, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP | - OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_OUTPUT_LOW | - OMAP_PIN_OFF_WAKEUPENABLE), - OMAP3_MUX(SYS_BOOT5, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP | - OMAP_PIN_OFF_NONE), - OMAP3_MUX(GPMC_WAIT2, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP | - OMAP_PIN_OFF_NONE), -#ifdef CONFIG_WILINK_PLATFORM_DATA - /* WLAN IRQ - GPIO 149 */ - OMAP3_MUX(UART1_RTS, OMAP_MUX_MODE4 | OMAP_PIN_INPUT), - - /* WLAN POWER ENABLE - GPIO 150 */ - OMAP3_MUX(UART1_CTS, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT), - - /* MMC2 SDIO pin muxes for WL12xx */ - OMAP3_MUX(SDMMC2_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP), - OMAP3_MUX(SDMMC2_CMD, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP), - OMAP3_MUX(SDMMC2_DAT0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP), - OMAP3_MUX(SDMMC2_DAT1, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP), - OMAP3_MUX(SDMMC2_DAT2, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP), - OMAP3_MUX(SDMMC2_DAT3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP), -#endif - { .reg_offset = OMAP_MUX_TERMINATOR }, -}; - -static struct omap_board_mux omap36x_board_mux[] __initdata = { - OMAP3_MUX(SYS_NIRQ, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP | - OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_OUTPUT_LOW | - OMAP_PIN_OFF_WAKEUPENABLE), - OMAP3_MUX(MCSPI1_CS1, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP | - OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_OUTPUT_LOW | - OMAP_PIN_OFF_WAKEUPENABLE), - /* AM/DM37x EVM: DSS data bus muxed with sys_boot */ - OMAP3_MUX(DSS_DATA18, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE), - OMAP3_MUX(DSS_DATA19, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE), - OMAP3_MUX(DSS_DATA22, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE), - OMAP3_MUX(DSS_DATA21, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE), - OMAP3_MUX(DSS_DATA22, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE), - OMAP3_MUX(DSS_DATA23, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE), - OMAP3_MUX(SYS_BOOT0, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE), - OMAP3_MUX(SYS_BOOT1, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE), - OMAP3_MUX(SYS_BOOT3, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE), - OMAP3_MUX(SYS_BOOT4, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE), - OMAP3_MUX(SYS_BOOT5, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE), - OMAP3_MUX(SYS_BOOT6, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE), -#ifdef CONFIG_WILINK_PLATFORM_DATA - /* WLAN IRQ - GPIO 149 */ - OMAP3_MUX(UART1_RTS, OMAP_MUX_MODE4 | OMAP_PIN_INPUT), - - /* WLAN POWER ENABLE - GPIO 150 */ - OMAP3_MUX(UART1_CTS, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT), - - /* MMC2 SDIO pin muxes for WL12xx */ - OMAP3_MUX(SDMMC2_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP), - OMAP3_MUX(SDMMC2_CMD, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP), - OMAP3_MUX(SDMMC2_DAT0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP), - OMAP3_MUX(SDMMC2_DAT1, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP), - OMAP3_MUX(SDMMC2_DAT2, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP), - OMAP3_MUX(SDMMC2_DAT3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP), -#endif - - { .reg_offset = OMAP_MUX_TERMINATOR }, -}; -#else -#define omap35x_board_mux NULL -#define omap36x_board_mux NULL -#endif - -static struct omap_musb_board_data musb_board_data = { - .interface_type = MUSB_INTERFACE_ULPI, - .mode = MUSB_OTG, - .power = 100, -}; - -static struct gpio omap3_evm_ehci_gpios[] __initdata = { - { OMAP3_EVM_EHCI_VBUS, GPIOF_OUT_INIT_HIGH, "enable EHCI VBUS" }, - { OMAP3_EVM_EHCI_SELECT, GPIOF_OUT_INIT_LOW, "select EHCI port" }, -}; - -static void __init omap3_evm_wl12xx_init(void) -{ -#ifdef CONFIG_WILINK_PLATFORM_DATA - int ret; - - /* WL12xx WLAN Init */ - omap3evm_wlan_data.irq = gpio_to_irq(OMAP3EVM_WLAN_IRQ_GPIO); - ret = wl12xx_set_platform_data(&omap3evm_wlan_data); - if (ret) - pr_err("error setting wl12xx data: %d\n", ret); - ret = platform_device_register(&omap3evm_wlan_regulator); - if (ret) - pr_err("error registering wl12xx device: %d\n", ret); -#endif -} - -static struct regulator_consumer_supply dummy_supplies[] = { - REGULATOR_SUPPLY("vddvario", "smsc911x.0"), - REGULATOR_SUPPLY("vdd33a", "smsc911x.0"), -}; - -static struct mtd_partition omap3evm_nand_partitions[] = { - /* All the partition sizes are listed in terms of NAND block size */ - { - .name = "X-Loader", - .offset = 0, - .size = 4*(SZ_128K), - .mask_flags = MTD_WRITEABLE - }, - { - .name = "U-Boot", - .offset = MTDPART_OFS_APPEND, - .size = 14*(SZ_128K), - .mask_flags = MTD_WRITEABLE - }, - { - .name = "U-Boot Env", - .offset = MTDPART_OFS_APPEND, - .size = 2*(SZ_128K) - }, - { - .name = "Kernel", - .offset = MTDPART_OFS_APPEND, - .size = 40*(SZ_128K) - }, - { - .name = "File system", - .size = MTDPART_SIZ_FULL, - .offset = MTDPART_OFS_APPEND, - }, -}; - -static void __init omap3_evm_init(void) -{ - struct omap_board_mux *obm; - - omap3_evm_get_revision(); - regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies)); - - obm = (cpu_is_omap3630()) ? omap36x_board_mux : omap35x_board_mux; - omap3_mux_init(obm, OMAP_PACKAGE_CBB); - - omap_mux_init_gpio(63, OMAP_PIN_INPUT); - omap_hsmmc_init(mmc); - - if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2) - omap3evm_twldata.vaux2 = &omap3evm_vaux2; - - omap3_evm_i2c_init(); - - omap_display_init(&omap3_evm_dss_data); - platform_device_register(&omap3_evm_lcd_device); - platform_device_register(&omap3_evm_tfp410_device); - platform_device_register(&omap3_evm_dvi_connector_device); - platform_device_register(&omap3_evm_tv_connector_device); - - omap_serial_init(); - omap_sdrc_init(mt46h32m32lf6_sdrc_params, NULL); - - /* OMAP3EVM uses ISP1504 phy and so register nop transceiver */ - usb_nop_xceiv_register(); - - if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2) { - /* enable EHCI VBUS using GPIO22 */ - omap_mux_init_gpio(OMAP3_EVM_EHCI_VBUS, OMAP_PIN_INPUT_PULLUP); - /* Select EHCI port on main board */ - omap_mux_init_gpio(OMAP3_EVM_EHCI_SELECT, - OMAP_PIN_INPUT_PULLUP); - gpio_request_array(omap3_evm_ehci_gpios, - ARRAY_SIZE(omap3_evm_ehci_gpios)); - - /* setup EHCI phy reset config */ - omap_mux_init_gpio(21, OMAP_PIN_INPUT_PULLUP); - phy_data[0].reset_gpio = 21; - - /* EVM REV >= E can supply 500mA with EXTVBUS programming */ - musb_board_data.power = 500; - musb_board_data.extvbus = 1; - } else { - /* setup EHCI phy reset on MDC */ - omap_mux_init_gpio(135, OMAP_PIN_OUTPUT); - phy_data[0].reset_gpio = 135; - } - usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb"); - usb_musb_init(&musb_board_data); - - usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data)); - usbhs_init(&usbhs_bdata); - board_nand_init(omap3evm_nand_partitions, - ARRAY_SIZE(omap3evm_nand_partitions), NAND_CS, - NAND_BUSWIDTH_16, NULL); - - omap_ads7846_init(1, OMAP3_EVM_TS_GPIO, 310, NULL); - omap3evm_init_smsc911x(); -#ifdef CONFIG_BROKEN - omap3_evm_display_init(); -#endif - omap3_evm_wl12xx_init(); - omap_twl4030_audio_init("omap3evm", NULL); -} - -MACHINE_START(OMAP3EVM, "OMAP3 EVM") - /* Maintainer: Syed Mohammed Khasim - Texas Instruments */ - .atag_offset = 0x100, - .reserve = omap_reserve, - .map_io = omap3_map_io, - .init_early = omap35xx_init_early, - .init_irq = omap3_init_irq, - .handle_irq = omap3_intc_handle_irq, - .init_machine = omap3_evm_init, - .init_late = omap35xx_init_late, - .init_time = omap3_sync32k_timer_init, - .restart = omap3xxx_restart, -MACHINE_END |
