diff options
Diffstat (limited to 'arch/arm/mach-kirkwood')
32 files changed, 570 insertions, 428 deletions
diff --git a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig index 2833492..f91cdff 100644 --- a/arch/arm/mach-kirkwood/Kconfig +++ b/arch/arm/mach-kirkwood/Kconfig @@ -46,6 +46,11 @@ config MACH_GURUPLUG config ARCH_KIRKWOOD_DT bool "Marvell Kirkwood Flattened Device Tree" + select POWER_SUPPLY + select POWER_RESET + select POWER_RESET_GPIO + select REGULATOR + select REGULATOR_FIXED_VOLTAGE select MVEBU_CLK_CORE select MVEBU_CLK_GATING select USE_OF @@ -132,6 +137,63 @@ config MACH_KM_KIRKWOOD_DT Say 'Y' here if you want your kernel to support the Keymile Kirkwood Reference Desgin, using Flattened Device Tree. +config MACH_INETSPACE_V2_DT + bool "LaCie Internet Space v2 NAS (Flattened Device Tree)" + select ARCH_KIRKWOOD_DT + help + Say 'Y' here if you want your kernel to support the LaCie + Internet Space v2 NAS, using Flattened Device Tree. + +config MACH_MPLCEC4_DT + bool "MPL CEC4 (Flattened Device Tree)" + select ARCH_KIRKWOOD_DT + help + Say 'Y' here if you want your kernel to support the + MPL CEC4 (Flattened Device Tree). + +config MACH_NETSPACE_V2_DT + bool "LaCie Network Space v2 NAS (Flattened Device Tree)" + select ARCH_KIRKWOOD_DT + help + Say 'Y' here if you want your kernel to support the LaCie + Network Space v2 NAS, using Flattened Device Tree. + +config MACH_NETSPACE_MAX_V2_DT + bool "LaCie Network Space Max v2 NAS (Flattened Device Tree)" + select ARCH_KIRKWOOD_DT + help + Say 'Y' here if you want your kernel to support the LaCie + Network Space Max v2 NAS, using Flattened Device Tree. + +config MACH_NETSPACE_LITE_V2_DT + bool "LaCie Network Space Lite v2 NAS (Flattened Device Tree)" + select ARCH_KIRKWOOD_DT + help + Say 'Y' here if you want your kernel to support the LaCie + Network Space Lite v2 NAS, using Flattened Device Tree. + +config MACH_NETSPACE_MINI_V2_DT + bool "LaCie Network Space Mini v2 NAS (Flattened Device Tree)" + select ARCH_KIRKWOOD_DT + help + Say 'Y' here if you want your kernel to support the LaCie + Network Space Mini v2 NAS (aka SafeBox), using Flattened + Device Tree. + +config MACH_OPENBLOCKS_A6_DT + bool "Plat'Home OpenBlocks A6 (Flattened Device Tree)" + select ARCH_KIRKWOOD_DT + help + Say 'Y' here if you want your kernel to support the + Plat'Home OpenBlocks A6 (Flattened Device Tree). + +config MACH_TOPKICK_DT + bool "USI Topkick (Flattened Device Tree)" + select ARCH_KIRKWOOD_DT + help + Say 'Y' here if you want your kernel to support the + USI Topkick, using Flattened Device Tree + config MACH_TS219 bool "QNAP TS-110, TS-119, TS-119P+, TS-210, TS-219, TS-219P and TS-219P+ Turbo NAS" help @@ -218,6 +280,14 @@ config MACH_T5325 Say 'Y' here if you want your kernel to support the HP t5325 Thin Client. +config MACH_NSA310_DT + bool "ZyXEL NSA-310 (Flattened Device Tree)" + select ARCH_KIRKWOOD_DT + select ARM_ATAG_DTB_COMPAT + help + Say 'Y' here if you want your kernel to support the + ZyXEL NSA-310 board (Flattened Device Tree). + endmenu endif diff --git a/arch/arm/mach-kirkwood/Makefile b/arch/arm/mach-kirkwood/Makefile index 294779f..8d2e5a9 100644 --- a/arch/arm/mach-kirkwood/Makefile +++ b/arch/arm/mach-kirkwood/Makefile @@ -31,3 +31,12 @@ obj-$(CONFIG_MACH_GOFLEXNET_DT) += board-goflexnet.o obj-$(CONFIG_MACH_LSXL_DT) += board-lsxl.o obj-$(CONFIG_MACH_IOMEGA_IX2_200_DT) += board-iomega_ix2_200.o obj-$(CONFIG_MACH_KM_KIRKWOOD_DT) += board-km_kirkwood.o +obj-$(CONFIG_MACH_INETSPACE_V2_DT) += board-ns2.o +obj-$(CONFIG_MACH_MPLCEC4_DT) += board-mplcec4.o +obj-$(CONFIG_MACH_NETSPACE_V2_DT) += board-ns2.o +obj-$(CONFIG_MACH_NETSPACE_MAX_V2_DT) += board-ns2.o +obj-$(CONFIG_MACH_NETSPACE_LITE_V2_DT) += board-ns2.o +obj-$(CONFIG_MACH_NETSPACE_MINI_V2_DT) += board-ns2.o +obj-$(CONFIG_MACH_NSA310_DT) += board-nsa310.o +obj-$(CONFIG_MACH_OPENBLOCKS_A6_DT) += board-openblocks_a6.o +obj-$(CONFIG_MACH_TOPKICK_DT) += board-usi_topkick.o diff --git a/arch/arm/mach-kirkwood/board-dnskw.c b/arch/arm/mach-kirkwood/board-dnskw.c index 43d16d6..a1aa87f 100644 --- a/arch/arm/mach-kirkwood/board-dnskw.c +++ b/arch/arm/mach-kirkwood/board-dnskw.c @@ -17,51 +17,11 @@ #include <linux/mv643xx_eth.h> #include <linux/gpio.h> #include "common.h" -#include "mpp.h" static struct mv643xx_eth_platform_data dnskw_ge00_data = { .phy_addr = MV643XX_ETH_PHY_ADDR(8), }; -static unsigned int dnskw_mpp_config[] __initdata = { - MPP13_UART1_TXD, /* Custom ... */ - MPP14_UART1_RXD, /* ... Controller (DNS-320 only) */ - MPP20_SATA1_ACTn, /* LED: White Right HDD */ - MPP21_SATA0_ACTn, /* LED: White Left HDD */ - MPP24_GPIO, - MPP25_GPIO, - MPP26_GPIO, /* LED: Power */ - MPP27_GPIO, /* LED: Red Right HDD */ - MPP28_GPIO, /* LED: Red Left HDD */ - MPP29_GPIO, /* LED: Red USB (DNS-325 only) */ - MPP30_GPIO, - MPP31_GPIO, - MPP32_GPIO, - MPP33_GPO, - MPP34_GPIO, /* Button: Front power */ - MPP35_GPIO, /* LED: Red USB (DNS-320 only) */ - MPP36_GPIO, /* Power: Turn off board */ - MPP37_GPIO, /* Power: Turn back on after power failure */ - MPP38_GPIO, - MPP39_GPIO, /* Power: SATA0 */ - MPP40_GPIO, /* Power: SATA1 */ - MPP41_GPIO, /* SATA0 present */ - MPP42_GPIO, /* SATA1 present */ - MPP43_GPIO, /* LED: White USB */ - MPP44_GPIO, /* Fan: Tachometer Pin */ - MPP45_GPIO, /* Fan: high speed */ - MPP46_GPIO, /* Fan: low speed */ - MPP47_GPIO, /* Button: Back unmount */ - MPP48_GPIO, /* Button: Back reset */ - MPP49_GPIO, /* Temp Alarm (DNS-325) Pin of U5 (DNS-320) */ - 0 -}; - -static void dnskw_power_off(void) -{ - gpio_set_value(36, 1); -} - /* Register any GPIO for output and set the value */ static void __init dnskw_gpio_register(unsigned gpio, char *name, int def) { @@ -76,22 +36,8 @@ static void __init dnskw_gpio_register(unsigned gpio, char *name, int def) void __init dnskw_init(void) { - kirkwood_mpp_conf(dnskw_mpp_config); - - kirkwood_ehci_init(); kirkwood_ge00_init(&dnskw_ge00_data); - /* Register power-off GPIO. */ - if (gpio_request(36, "dnskw:power:off") == 0 - && gpio_direction_output(36, 0) == 0) - pm_power_off = dnskw_power_off; - else - pr_err("dnskw: failed to configure power-off GPIO\n"); - - /* Ensure power is supplied to both HDDs */ - dnskw_gpio_register(39, "dnskw:power:sata0", 1); - dnskw_gpio_register(40, "dnskw:power:sata1", 1); - /* Set NAS to turn back on after a power failure */ dnskw_gpio_register(37, "dnskw:power:recover", 1); } diff --git a/arch/arm/mach-kirkwood/board-dockstar.c b/arch/arm/mach-kirkwood/board-dockstar.c index f2fbb02..d7196db 100644 --- a/arch/arm/mach-kirkwood/board-dockstar.c +++ b/arch/arm/mach-kirkwood/board-dockstar.c @@ -16,46 +16,17 @@ #include <linux/kernel.h> #include <linux/init.h> -#include <linux/platform_device.h> -#include <linux/ata_platform.h> #include <linux/mv643xx_eth.h> -#include <linux/of.h> -#include <linux/of_address.h> -#include <linux/of_fdt.h> -#include <linux/of_irq.h> -#include <linux/of_platform.h> -#include <linux/gpio.h> -#include <asm/mach-types.h> -#include <asm/mach/arch.h> -#include <asm/mach/map.h> -#include <mach/kirkwood.h> -#include <mach/bridge-regs.h> -#include <linux/platform_data/mmc-mvsdio.h> #include "common.h" -#include "mpp.h" static struct mv643xx_eth_platform_data dockstar_ge00_data = { .phy_addr = MV643XX_ETH_PHY_ADDR(0), }; -static unsigned int dockstar_mpp_config[] __initdata = { - MPP29_GPIO, /* USB Power Enable */ - MPP46_GPIO, /* LED green */ - MPP47_GPIO, /* LED orange */ - 0 -}; - void __init dockstar_dt_init(void) { /* * Basic setup. Needs to be called early. */ - kirkwood_mpp_conf(dockstar_mpp_config); - - if (gpio_request(29, "USB Power Enable") != 0 || - gpio_direction_output(29, 1) != 0) - pr_err("can't setup GPIO 29 (USB Power Enable)\n"); - kirkwood_ehci_init(); - kirkwood_ge00_init(&dockstar_ge00_data); } diff --git a/arch/arm/mach-kirkwood/board-dreamplug.c b/arch/arm/mach-kirkwood/board-dreamplug.c index 20af53a..08248e2 100644 --- a/arch/arm/mach-kirkwood/board-dreamplug.c +++ b/arch/arm/mach-kirkwood/board-dreamplug.c @@ -13,26 +13,10 @@ #include <linux/kernel.h> #include <linux/init.h> -#include <linux/platform_device.h> -#include <linux/ata_platform.h> #include <linux/mv643xx_eth.h> -#include <linux/of.h> -#include <linux/of_address.h> -#include <linux/of_fdt.h> -#include <linux/of_irq.h> -#include <linux/of_platform.h> #include <linux/gpio.h> -#include <linux/mtd/physmap.h> -#include <linux/spi/flash.h> -#include <linux/spi/spi.h> -#include <asm/mach-types.h> -#include <asm/mach/arch.h> -#include <asm/mach/map.h> -#include <mach/kirkwood.h> -#include <mach/bridge-regs.h> #include <linux/platform_data/mmc-mvsdio.h> #include "common.h" -#include "mpp.h" static struct mv643xx_eth_platform_data dreamplug_ge00_data = { .phy_addr = MV643XX_ETH_PHY_ADDR(0), @@ -46,25 +30,11 @@ static struct mvsdio_platform_data dreamplug_mvsdio_data = { /* unfortunately the CD signal has not been connected */ }; -static unsigned int dreamplug_mpp_config[] __initdata = { - MPP0_SPI_SCn, - MPP1_SPI_MOSI, - MPP2_SPI_SCK, - MPP3_SPI_MISO, - MPP47_GPIO, /* Bluetooth LED */ - MPP48_GPIO, /* Wifi LED */ - MPP49_GPIO, /* Wifi AP LED */ - 0 -}; - void __init dreamplug_init(void) { /* * Basic setup. Needs to be called early. */ - kirkwood_mpp_conf(dreamplug_mpp_config); - - kirkwood_ehci_init(); kirkwood_ge00_init(&dreamplug_ge00_data); kirkwood_ge01_init(&dreamplug_ge01_data); kirkwood_sdio_init(&dreamplug_mvsdio_data); diff --git a/arch/arm/mach-kirkwood/board-dt.c b/arch/arm/mach-kirkwood/board-dt.c index 9826904..ff4150a 100644 --- a/arch/arm/mach-kirkwood/board-dt.c +++ b/arch/arm/mach-kirkwood/board-dt.c @@ -128,10 +128,29 @@ static void __init kirkwood_dt_init(void) if (of_machine_is_compatible("keymile,km_kirkwood")) km_kirkwood_init(); + if (of_machine_is_compatible("lacie,inetspace_v2") || + of_machine_is_compatible("lacie,netspace_v2") || + of_machine_is_compatible("lacie,netspace_max_v2") || + of_machine_is_compatible("lacie,netspace_lite_v2") || + of_machine_is_compatible("lacie,netspace_mini_v2")) + ns2_init(); + + if (of_machine_is_compatible("mpl,cec4")) + mplcec4_init(); + + if (of_machine_is_compatible("plathome,openblocks-a6")) + openblocks_a6_init(); + + if (of_machine_is_compatible("usi,topkick")) + usi_topkick_init(); + + if (of_machine_is_compatible("zyxel,nsa310")) + nsa310_init(); + of_platform_populate(NULL, kirkwood_dt_match_table, NULL, NULL); } -static const char *kirkwood_dt_board_compat[] = { +static const char * const kirkwood_dt_board_compat[] = { "globalscale,dreamplug", "dlink,dns-320", "dlink,dns-325", @@ -143,6 +162,15 @@ static const char *kirkwood_dt_board_compat[] = { "buffalo,lsxl", "iom,ix2-200", "keymile,km_kirkwood", + "lacie,inetspace_v2", + "lacie,netspace_max_v2", + "lacie,netspace_v2", + "lacie,netspace_lite_v2", + "lacie,netspace_mini_v2", + "mpl,cec4", + "plathome,openblocks-a6", + "usi,topkick", + "zyxel,nsa310", NULL }; diff --git a/arch/arm/mach-kirkwood/board-goflexnet.c b/arch/arm/mach-kirkwood/board-goflexnet.c index 001ca8c..9db979a 100644 --- a/arch/arm/mach-kirkwood/board-goflexnet.c +++ b/arch/arm/mach-kirkwood/board-goflexnet.c @@ -18,54 +18,17 @@ #include <linux/kernel.h> #include <linux/init.h> -#include <linux/platform_device.h> -#include <linux/ata_platform.h> #include <linux/mv643xx_eth.h> -#include <linux/of.h> -#include <linux/of_address.h> -#include <linux/of_fdt.h> -#include <linux/of_irq.h> -#include <linux/of_platform.h> -#include <linux/gpio.h> -#include <asm/mach-types.h> -#include <asm/mach/arch.h> -#include <asm/mach/map.h> -#include <mach/kirkwood.h> -#include <mach/bridge-regs.h> -#include <linux/platform_data/mmc-mvsdio.h> #include "common.h" -#include "mpp.h" static struct mv643xx_eth_platform_data goflexnet_ge00_data = { .phy_addr = MV643XX_ETH_PHY_ADDR(0), }; -static unsigned int goflexnet_mpp_config[] __initdata = { - MPP29_GPIO, /* USB Power Enable */ - MPP47_GPIO, /* LED Orange */ - MPP46_GPIO, /* LED Green */ - MPP45_GPIO, /* LED Left Capacity 3 */ - MPP44_GPIO, /* LED Left Capacity 2 */ - MPP43_GPIO, /* LED Left Capacity 1 */ - MPP42_GPIO, /* LED Left Capacity 0 */ - MPP41_GPIO, /* LED Right Capacity 3 */ - MPP40_GPIO, /* LED Right Capacity 2 */ - MPP39_GPIO, /* LED Right Capacity 1 */ - MPP38_GPIO, /* LED Right Capacity 0 */ - 0 -}; - void __init goflexnet_init(void) { /* * Basic setup. Needs to be called early. */ - kirkwood_mpp_conf(goflexnet_mpp_config); - - if (gpio_request(29, "USB Power Enable") != 0 || - gpio_direction_output(29, 1) != 0) - pr_err("can't setup GPIO 29 (USB Power Enable)\n"); - kirkwood_ehci_init(); - kirkwood_ge00_init(&goflexnet_ge00_data); } diff --git a/arch/arm/mach-kirkwood/board-ib62x0.c b/arch/arm/mach-kirkwood/board-ib62x0.c index cfc47f8..9f6f496 100644 --- a/arch/arm/mach-kirkwood/board-ib62x0.c +++ b/arch/arm/mach-kirkwood/board-ib62x0.c @@ -13,59 +13,18 @@ #include <linux/kernel.h> #include <linux/init.h> -#include <linux/platform_device.h> -#include <linux/mtd/partitions.h> -#include <linux/ata_platform.h> #include <linux/mv643xx_eth.h> -#include <linux/gpio.h> #include <linux/input.h> -#include <asm/mach-types.h> -#include <asm/mach/arch.h> -#include <mach/kirkwood.h> #include "common.h" -#include "mpp.h" - -#define IB62X0_GPIO_POWER_OFF 24 static struct mv643xx_eth_platform_data ib62x0_ge00_data = { .phy_addr = MV643XX_ETH_PHY_ADDR(8), }; -static unsigned int ib62x0_mpp_config[] __initdata = { - MPP0_NF_IO2, - MPP1_NF_IO3, - MPP2_NF_IO4, - MPP3_NF_IO5, - MPP4_NF_IO6, - MPP5_NF_IO7, - MPP18_NF_IO0, - MPP19_NF_IO1, - MPP22_GPIO, /* OS LED red */ - MPP24_GPIO, /* Power off device */ - MPP25_GPIO, /* OS LED green */ - MPP27_GPIO, /* USB transfer LED */ - MPP28_GPIO, /* Reset button */ - MPP29_GPIO, /* USB Copy button */ - 0 -}; - -static void ib62x0_power_off(void) -{ - gpio_set_value(IB62X0_GPIO_POWER_OFF, 1); -} - void __init ib62x0_init(void) { /* * Basic setup. Needs to be called early. */ - kirkwood_mpp_conf(ib62x0_mpp_config); - - kirkwood_ehci_init(); kirkwood_ge00_init(&ib62x0_ge00_data); - if (gpio_request(IB62X0_GPIO_POWER_OFF, "ib62x0:power:off") == 0 && - gpio_direction_output(IB62X0_GPIO_POWER_OFF, 0) == 0) - pm_power_off = ib62x0_power_off; - else - pr_err("board-ib62x0: failed to configure power-off GPIO\n"); } diff --git a/arch/arm/mach-kirkwood/board-iconnect.c b/arch/arm/mach-kirkwood/board-iconnect.c index d084b1e..c8ebde4 100644 --- a/arch/arm/mach-kirkwood/board-iconnect.c +++ b/arch/arm/mach-kirkwood/board-iconnect.c @@ -10,42 +10,16 @@ #include <linux/kernel.h> #include <linux/init.h> -#include <linux/platform_device.h> #include <linux/of.h> -#include <linux/of_address.h> -#include <linux/of_fdt.h> -#include <linux/of_irq.h> -#include <linux/of_platform.h> #include <linux/mv643xx_eth.h> -#include <linux/gpio.h> -#include <asm/mach/arch.h> -#include <mach/kirkwood.h> #include "common.h" -#include "mpp.h" static struct mv643xx_eth_platform_data iconnect_ge00_data = { .phy_addr = MV643XX_ETH_PHY_ADDR(11), }; -static unsigned int iconnect_mpp_config[] __initdata = { - MPP12_GPIO, - MPP35_GPIO, - MPP41_GPIO, - MPP42_GPIO, - MPP43_GPIO, - MPP44_GPIO, - MPP45_GPIO, - MPP46_GPIO, - MPP47_GPIO, - MPP48_GPIO, - 0 -}; - void __init iconnect_init(void) { - kirkwood_mpp_conf(iconnect_mpp_config); - - kirkwood_ehci_init(); kirkwood_ge00_init(&iconnect_ge00_data); } diff --git a/arch/arm/mach-kirkwood/board-iomega_ix2_200.c b/arch/arm/mach-kirkwood/board-iomega_ix2_200.c index 158fb97..f655b26 100644 --- a/arch/arm/mach-kirkwood/board-iomega_ix2_200.c +++ b/arch/arm/mach-kirkwood/board-iomega_ix2_200.c @@ -10,12 +10,9 @@ #include <linux/kernel.h> #include <linux/init.h> -#include <linux/platform_device.h> #include <linux/mv643xx_eth.h> #include <linux/ethtool.h> -#include <mach/kirkwood.h> #include "common.h" -#include "mpp.h" static struct mv643xx_eth_platform_data iomega_ix2_200_ge00_data = { .phy_addr = MV643XX_ETH_PHY_NONE, @@ -23,35 +20,10 @@ static struct mv643xx_eth_platform_data iomega_ix2_200_ge00_data = { .duplex = DUPLEX_FULL, }; -static unsigned int iomega_ix2_200_mpp_config[] __initdata = { - MPP12_GPIO, /* Reset Button */ - MPP14_GPIO, /* Power Button */ - MPP15_GPIO, /* Backup LED (blue) */ - MPP16_GPIO, /* Power LED (white) */ - MPP35_GPIO, /* OTB Button */ - MPP36_GPIO, /* Rebuild LED (white) */ - MPP37_GPIO, /* Health LED (red) */ - MPP38_GPIO, /* SATA LED brightness control 1 */ - MPP39_GPIO, /* SATA LED brightness control 2 */ - MPP40_GPIO, /* Backup LED brightness control 1 */ - MPP41_GPIO, /* Backup LED brightness control 2 */ - MPP42_GPIO, /* Power LED brightness control 1 */ - MPP43_GPIO, /* Power LED brightness control 2 */ - MPP44_GPIO, /* Health LED brightness control 1 */ - MPP45_GPIO, /* Health LED brightness control 2 */ - MPP46_GPIO, /* Rebuild LED brightness control 1 */ - MPP47_GPIO, /* Rebuild LED brightness control 2 */ - 0 -}; - void __init iomega_ix2_200_init(void) { /* * Basic setup. Needs to be called early. */ - kirkwood_mpp_conf(iomega_ix2_200_mpp_config); - - kirkwood_ehci_init(); - kirkwood_ge01_init(&iomega_ix2_200_ge00_data); } diff --git a/arch/arm/mach-kirkwood/board-km_kirkwood.c b/arch/arm/mach-kirkwood/board-km_kirkwood.c index f7d3283..44e4605 100644 --- a/arch/arm/mach-kirkwood/board-km_kirkwood.c +++ b/arch/arm/mach-kirkwood/board-km_kirkwood.c @@ -18,27 +18,15 @@ #include <linux/clk.h> #include <linux/clk-private.h> #include "common.h" -#include "mpp.h" static struct mv643xx_eth_platform_data km_kirkwood_ge00_data = { .phy_addr = MV643XX_ETH_PHY_ADDR(0), }; -static unsigned int km_kirkwood_mpp_config[] __initdata = { - MPP8_GPIO, /* I2C SDA */ - MPP9_GPIO, /* I2C SCL */ - 0 -}; - void __init km_kirkwood_init(void) { struct clk *sata_clk; /* - * Basic setup. Needs to be called early. - */ - kirkwood_mpp_conf(km_kirkwood_mpp_config); - - /* * Our variant of kirkwood (integrated in the Bobcat) hangs on accessing * SATA bits (14-15) of the Clock Gating Control Register. Since these * devices are also not present in this variant, their clocks get @@ -52,6 +40,5 @@ void __init km_kirkwood_init(void) if (!IS_ERR(sata_clk)) sata_clk->flags |= CLK_IGNORE_UNUSED; - kirkwood_ehci_init(); kirkwood_ge00_init(&km_kirkwood_ge00_data); } diff --git a/arch/arm/mach-kirkwood/board-lsxl.c b/arch/arm/mach-kirkwood/board-lsxl.c index 83d8975..4ec8b7a 100644 --- a/arch/arm/mach-kirkwood/board-lsxl.c +++ b/arch/arm/mach-kirkwood/board-lsxl.c @@ -14,19 +14,8 @@ #include <linux/kernel.h> #include <linux/init.h> #include <linux/platform_device.h> -#include <linux/mtd/partitions.h> -#include <linux/ata_platform.h> -#include <linux/spi/flash.h> -#include <linux/spi/spi.h> #include <linux/mv643xx_eth.h> -#include <linux/gpio.h> -#include <linux/gpio-fan.h> -#include <linux/input.h> -#include <asm/mach-types.h> -#include <asm/mach/arch.h> -#include <mach/kirkwood.h> #include "common.h" -#include "mpp.h" static struct mv643xx_eth_platform_data lsxl_ge00_data = { .phy_addr = MV643XX_ETH_PHY_ADDR(0), @@ -36,68 +25,6 @@ static struct mv643xx_eth_platform_data lsxl_ge01_data = { .phy_addr = MV643XX_ETH_PHY_ADDR(8), }; -static unsigned int lsxl_mpp_config[] __initdata = { - MPP10_GPO, /* HDD Power Enable */ - MPP11_GPIO, /* USB Vbus Enable */ - MPP18_GPO, /* FAN High Enable# */ - MPP19_GPO, /* FAN Low Enable# */ - MPP36_GPIO, /* Function Blue LED */ - MPP37_GPIO, /* Alarm LED */ - MPP38_GPIO, /* Info LED */ - MPP39_GPIO, /* Power LED */ - MPP40_GPIO, /* Fan Lock */ - MPP41_GPIO, /* Function Button */ - MPP42_GPIO, /* Power Switch */ - MPP43_GPIO, /* Power Auto Switch */ - MPP48_GPIO, /* Function Red LED */ - 0 -}; - -#define LSXL_GPIO_FAN_HIGH 18 -#define LSXL_GPIO_FAN_LOW 19 -#define LSXL_GPIO_FAN_LOCK 40 - -static struct gpio_fan_alarm lsxl_alarm = { - .gpio = LSXL_GPIO_FAN_LOCK, -}; - -static struct gpio_fan_speed lsxl_speeds[] = { - { - .rpm = 0, - .ctrl_val = 3, - }, { - .rpm = 1500, - .ctrl_val = 1, - }, { - .rpm = 3250, - .ctrl_val = 2, - }, { - .rpm = 5000, - .ctrl_val = 0, - } -}; - -static int lsxl_gpio_list[] = { - LSXL_GPIO_FAN_HIGH, LSXL_GPIO_FAN_LOW, -}; - -static struct gpio_fan_platform_data lsxl_fan_data = { - .num_ctrl = ARRAY_SIZE(lsxl_gpio_list), - .ctrl = lsxl_gpio_list, - .alarm = &lsxl_alarm, - .num_speed = ARRAY_SIZE(lsxl_speeds), - .speed = lsxl_speeds, -}; - -static struct platform_device lsxl_fan_device = { - .name = "gpio-fan", - .id = -1, - .num_resources = 0, - .dev = { - .platform_data = &lsxl_fan_data, - }, -}; - /* * On the LS-XHL/LS-CHLv2, the shutdown process is following: * - Userland monitors key events until the power switch goes to off position @@ -111,24 +38,14 @@ static void lsxl_power_off(void) kirkwood_restart('h', NULL); } -#define LSXL_GPIO_HDD_POWER 10 -#define LSXL_GPIO_USB_POWER 11 - void __init lsxl_init(void) { /* * Basic setup. Needs to be called early. */ - kirkwood_mpp_conf(lsxl_mpp_config); - - /* usb and sata power on */ - gpio_set_value(LSXL_GPIO_USB_POWER, 1); - gpio_set_value(LSXL_GPIO_HDD_POWER, 1); - kirkwood_ehci_init(); kirkwood_ge00_init(&lsxl_ge00_data); kirkwood_ge01_init(&lsxl_ge01_data); - platform_device_register(&lsxl_fan_device); /* register power-off method */ pm_power_off = lsxl_power_off; diff --git a/arch/arm/mach-kirkwood/board-mplcec4.c b/arch/arm/mach-kirkwood/board-mplcec4.c new file mode 100644 index 0000000..56bfe5a --- /dev/null +++ b/arch/arm/mach-kirkwood/board-mplcec4.c @@ -0,0 +1,44 @@ +/* + * Copyright (C) 2012 MPL AG, Switzerland + * Stefan Peter <s.peter@mpl.ch> + * + * arch/arm/mach-kirkwood/board-mplcec4.c + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/mv643xx_eth.h> +#include <linux/platform_data/mmc-mvsdio.h> +#include "common.h" +#include "mpp.h" + +static struct mv643xx_eth_platform_data mplcec4_ge00_data = { + .phy_addr = MV643XX_ETH_PHY_ADDR(1), +}; + +static struct mv643xx_eth_platform_data mplcec4_ge01_data = { + .phy_addr = MV643XX_ETH_PHY_ADDR(2), +}; + +static struct mvsdio_platform_data mplcec4_mvsdio_data = { + .gpio_card_detect = 47, /* MPP47 used as SD card detect */ +}; + + +void __init mplcec4_init(void) +{ + /* + * Basic setup. Needs to be called early. + */ + kirkwood_ge00_init(&mplcec4_ge00_data); + kirkwood_ge01_init(&mplcec4_ge01_data); + kirkwood_sdio_init(&mplcec4_mvsdio_data); + kirkwood_pcie_init(KW_PCIE0); +} + + + diff --git a/arch/arm/mach-kirkwood/board-ns2.c b/arch/arm/mach-kirkwood/board-ns2.c new file mode 100644 index 0000000..8821720 --- /dev/null +++ b/arch/arm/mach-kirkwood/board-ns2.c @@ -0,0 +1,86 @@ +/* + * Copyright 2012 (C), Simon Guinot <simon.guinot@sequanux.org> + * + * arch/arm/mach-kirkwood/board-ns2.c + * + * LaCie Network Space v2 board (and parents) initialization for drivers + * not converted to flattened device tree yet. + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/mv643xx_eth.h> +#include <linux/gpio.h> +#include <linux/of.h> +#include "common.h" +#include "mpp.h" + +static struct mv643xx_eth_platform_data ns2_ge00_data = { + .phy_addr = MV643XX_ETH_PHY_ADDR(8), +}; + +static unsigned int ns2_mpp_config[] __initdata = { + MPP0_SPI_SCn, + MPP1_SPI_MOSI, + MPP2_SPI_SCK, + MPP3_SPI_MISO, + MPP4_NF_IO6, + MPP5_NF_IO7, + MPP6_SYSRST_OUTn, + MPP7_GPO, /* Fan speed (bit 1) */ + MPP8_TW0_SDA, + MPP9_TW0_SCK, + MPP10_UART0_TXD, + MPP11_UART0_RXD, + MPP12_GPO, /* Red led */ + MPP14_GPIO, /* USB fuse */ + MPP16_GPIO, /* SATA 0 power */ + MPP17_GPIO, /* SATA 1 power */ + MPP18_NF_IO0, + MPP19_NF_IO1, + MPP20_SATA1_ACTn, + MPP21_SATA0_ACTn, + MPP22_GPIO, /* Fan speed (bit 0) */ + MPP23_GPIO, /* Fan power */ + MPP24_GPIO, /* USB mode select */ + MPP25_GPIO, /* Fan rotation fail */ + MPP26_GPIO, /* USB device vbus */ + MPP28_GPIO, /* USB enable host vbus */ + MPP29_GPIO, /* Blue led (slow register) */ + MPP30_GPIO, /* Blue led (command register) */ + MPP31_GPIO, /* Board power off */ + MPP32_GPIO, /* Power button (0 = Released, 1 = Pushed) */ + MPP33_GPO, /* Fan speed (bit 2) */ + 0 +}; + +#define NS2_GPIO_POWER_OFF 31 + +static void ns2_power_off(void) +{ + gpio_set_value(NS2_GPIO_POWER_OFF, 1); +} + +void __init ns2_init(void) +{ + /* + * Basic setup. Needs to be called early. + */ + kirkwood_mpp_conf(ns2_mpp_config); + + if (of_machine_is_compatible("lacie,netspace_lite_v2") || + of_machine_is_compatible("lacie,netspace_mini_v2")) + ns2_ge00_data.phy_addr = MV643XX_ETH_PHY_ADDR(0); + kirkwood_ge00_init(&ns2_ge00_data); + + if (gpio_request(NS2_GPIO_POWER_OFF, "power-off") == 0 && + gpio_direction_output(NS2_GPIO_POWER_OFF, 0) == 0) + pm_power_off = ns2_power_off; + else + pr_err("ns2: failed to configure power-off GPIO\n"); +} diff --git a/arch/arm/mach-kirkwood/board-nsa310.c b/arch/arm/mach-kirkwood/board-nsa310.c new file mode 100644 index 0000000..f58d2e1 --- /dev/null +++ b/arch/arm/mach-kirkwood/board-nsa310.c @@ -0,0 +1,101 @@ +/* + * arch/arm/mach-kirkwood/nsa-310-setup.c + * + * ZyXEL NSA-310 Setup + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/i2c.h> +#include <linux/gpio.h> + +#include <asm/mach-types.h> +#include <asm/mach/arch.h> +#include <mach/kirkwood.h> +#include "common.h" +#include "mpp.h" + +#define NSA310_GPIO_USB_POWER_OFF 21 +#define NSA310_GPIO_POWER_OFF 48 + +static unsigned int nsa310_mpp_config[] __initdata = { + MPP12_GPIO, /* led esata green */ + MPP13_GPIO, /* led esata red */ + MPP15_GPIO, /* led usb green */ + MPP16_GPIO, /* led usb red */ + MPP21_GPIO, /* control usb power off */ + MPP28_GPIO, /* led sys green */ + MPP29_GPIO, /* led sys red */ + MPP36_GPIO, /* key reset */ + MPP37_GPIO, /* key copy */ + MPP39_GPIO, /* led copy green */ + MPP40_GPIO, /* led copy red */ + MPP41_GPIO, /* led hdd green */ + MPP42_GPIO, /* led hdd red */ + MPP44_GPIO, /* ?? */ + MPP46_GPIO, /* key power */ + MPP48_GPIO, /* control power off */ + 0 +}; + +static struct i2c_board_info __initdata nsa310_i2c_info[] = { + { I2C_BOARD_INFO("adt7476", 0x2e) }, +}; + +static void nsa310_power_off(void) +{ + gpio_set_value(NSA310_GPIO_POWER_OFF, 1); +} + +static int __init nsa310_gpio_request(unsigned int gpio, unsigned long flags, + const char *label) +{ + int err; + + err = gpio_request_one(gpio, flags, label); + if (err) + pr_err("NSA-310: can't setup GPIO%u (%s), err=%d\n", + gpio, label, err); + + return err; +} + +static void __init nsa310_gpio_init(void) +{ + int err; + + err = nsa310_gpio_request(NSA310_GPIO_POWER_OFF, GPIOF_OUT_INIT_LOW, + "Power Off"); + if (!err) + pm_power_off = nsa310_power_off; + + nsa310_gpio_request(NSA310_GPIO_USB_POWER_OFF, GPIOF_OUT_INIT_LOW, + "USB Power Off"); +} + +void __init nsa310_init(void) +{ + u32 dev, rev; + + kirkwood_mpp_conf(nsa310_mpp_config); + + nsa310_gpio_init(); + + kirkwood_pcie_id(&dev, &rev); + + i2c_register_board_info(0, ARRAY_AND_SIZE(nsa310_i2c_info)); +} + +static int __init nsa310_pci_init(void) +{ + if (of_machine_is_compatible("zyxel,nsa310")) + kirkwood_pcie_init(KW_PCIE0); + + return 0; +} + +subsys_initcall(nsa310_pci_init); diff --git a/arch/arm/mach-kirkwood/board-openblocks_a6.c b/arch/arm/mach-kirkwood/board-openblocks_a6.c new file mode 100644 index 0000000..815fc64 --- /dev/null +++ b/arch/arm/mach-kirkwood/board-openblocks_a6.c @@ -0,0 +1,70 @@ +/* + * Copyright 2012 Nobuhiro Iwamatsu <iwamatsu@nigauri.org> + * + * arch/arm/mach-kirkwood/board-openblocks_a6.c + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/mv643xx_eth.h> +#include <linux/clk.h> +#include <linux/clk-private.h> +#include "common.h" +#include "mpp.h" + +static struct mv643xx_eth_platform_data openblocks_ge00_data = { + .phy_addr = MV643XX_ETH_PHY_ADDR(0), +}; + +static unsigned int openblocks_a6_mpp_config[] __initdata = { + MPP0_NF_IO2, + MPP1_NF_IO3, + MPP2_NF_IO4, + MPP3_NF_IO5, + MPP4_NF_IO6, + MPP5_NF_IO7, + MPP6_SYSRST_OUTn, + MPP8_UART1_RTS, + MPP9_UART1_CTS, + MPP10_UART0_TXD, + MPP11_UART0_RXD, + MPP13_UART1_TXD, + MPP14_UART1_RXD, + MPP15_UART0_RTS, + MPP16_UART0_CTS, + MPP18_NF_IO0, + MPP19_NF_IO1, + MPP20_GPIO, /* DIP SW0 */ + MPP21_GPIO, /* DIP SW1 */ + MPP22_GPIO, /* DIP SW2 */ + MPP23_GPIO, /* DIP SW3 */ + MPP24_GPIO, /* GPIO 0 */ + MPP25_GPIO, /* GPIO 1 */ + MPP26_GPIO, /* GPIO 2 */ + MPP27_GPIO, /* GPIO 3 */ + MPP28_GPIO, /* GPIO 4 */ + MPP29_GPIO, /* GPIO 5 */ + MPP30_GPIO, /* GPIO 6 */ + MPP31_GPIO, /* GPIO 7 */ + MPP36_TW1_SDA, + MPP37_TW1_SCK, + MPP38_GPIO, /* INIT */ + MPP39_GPIO, /* USB OC */ + MPP41_GPIO, /* LED: Red */ + MPP42_GPIO, /* LED: Green */ + MPP43_GPIO, /* LED: Yellow */ + 0, +}; + +void __init openblocks_a6_init(void) +{ + /* + * Basic setup. Needs to be called early. + */ + kirkwood_mpp_conf(openblocks_a6_mpp_config); + kirkwood_ge00_init(&openblocks_ge00_data); +} diff --git a/arch/arm/mach-kirkwood/board-ts219.c b/arch/arm/mach-kirkwood/board-ts219.c index 1750e68..acb0187 100644 --- a/arch/arm/mach-kirkwood/board-ts219.c +++ b/arch/arm/mach-kirkwood/board-ts219.c @@ -19,54 +19,25 @@ #include <linux/init.h> #include <linux/platform_device.h> #include <linux/mv643xx_eth.h> -#include <linux/ata_platform.h> -#include <linux/gpio_keys.h> -#include <linux/input.h> #include <asm/mach-types.h> #include <asm/mach/arch.h> #include <mach/kirkwood.h> #include "common.h" -#include "mpp.h" #include "tsx1x-common.h" static struct mv643xx_eth_platform_data qnap_ts219_ge00_data = { .phy_addr = MV643XX_ETH_PHY_ADDR(8), }; -static unsigned int qnap_ts219_mpp_config[] __initdata = { - MPP0_SPI_SCn, - MPP1_SPI_MOSI, - MPP2_SPI_SCK, - MPP3_SPI_MISO, - MPP4_SATA1_ACTn, - MPP5_SATA0_ACTn, - MPP8_TW0_SDA, - MPP9_TW0_SCK, - MPP10_UART0_TXD, - MPP11_UART0_RXD, - MPP13_UART1_TXD, /* PIC controller */ - MPP14_UART1_RXD, /* PIC controller */ - MPP15_GPIO, /* USB Copy button (on devices with 88F6281) */ - MPP16_GPIO, /* Reset button (on devices with 88F6281) */ - MPP36_GPIO, /* RAM: 0: 256 MB, 1: 512 MB */ - MPP37_GPIO, /* Reset button (on devices with 88F6282) */ - MPP43_GPIO, /* USB Copy button (on devices with 88F6282) */ - MPP44_GPIO, /* Board ID: 0: TS-11x, 1: TS-21x */ - 0 -}; - void __init qnap_dt_ts219_init(void) { u32 dev, rev; - kirkwood_mpp_conf(qnap_ts219_mpp_config); - kirkwood_pcie_id(&dev, &rev); if (dev == MV88F6282_DEV_ID) qnap_ts219_ge00_data.phy_addr = MV643XX_ETH_PHY_ADDR(0); kirkwood_ge00_init(&qnap_ts219_ge00_data); - kirkwood_ehci_init(); pm_power_off = qnap_tsx1x_power_off; } diff --git a/arch/arm/mach-kirkwood/board-usi_topkick.c b/arch/arm/mach-kirkwood/board-usi_topkick.c new file mode 100644 index 0000000..15e69fc --- /dev/null +++ b/arch/arm/mach-kirkwood/board-usi_topkick.c @@ -0,0 +1,81 @@ +/* + * Copyright 2012 (C), Jason Cooper <jason@lakedaemon.net> + * + * arch/arm/mach-kirkwood/board-usi_topkick.c + * + * USI Topkick Init for drivers not converted to flattened device tree yet. + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/mv643xx_eth.h> +#include <linux/gpio.h> +#include <linux/platform_data/mmc-mvsdio.h> +#include "common.h" +#include "mpp.h" + +static struct mv643xx_eth_platform_data topkick_ge00_data = { + .phy_addr = MV643XX_ETH_PHY_ADDR(0), +}; + +static struct mvsdio_platform_data topkick_mvsdio_data = { + /* unfortunately the CD signal has not been connected */ +}; + +/* + * GPIO LED layout + * + * /-SYS_LED(2) + * | + * | /-DISK_LED + * | | + * | | /-WLAN_LED(2) + * | | | + * [SW] [*] [*] [*] + */ + +/* + * Switch positions + * + * /-SW_LEFT + * | + * | /-SW_IDLE + * | | + * | | /-SW_RIGHT + * | | | + * PS [L] [I] [R] LEDS + */ + +static unsigned int topkick_mpp_config[] __initdata = { + MPP21_GPIO, /* DISK_LED (low active) - yellow */ + MPP36_GPIO, /* SATA0 power enable (high active) */ + MPP37_GPIO, /* SYS_LED2 (low active) - red */ + MPP38_GPIO, /* SYS_LED (low active) - blue */ + MPP39_GPIO, /* WLAN_LED (low active) - green */ + MPP43_GPIO, /* SW_LEFT (low active) */ + MPP44_GPIO, /* SW_RIGHT (low active) */ + MPP45_GPIO, /* SW_IDLE (low active) */ + MPP46_GPIO, /* SW_LEFT (low active) */ + MPP48_GPIO, /* WLAN_LED2 (low active) - yellow */ + 0 +}; + +#define TOPKICK_SATA0_PWR_ENABLE 36 + +void __init usi_topkick_init(void) +{ + /* + * Basic setup. Needs to be called early. + */ + kirkwood_mpp_conf(topkick_mpp_config); + + /* SATA0 power enable */ + gpio_set_value(TOPKICK_SATA0_PWR_ENABLE, 1); + + kirkwood_ge00_init(&topkick_ge00_data); + kirkwood_sdio_init(&topkick_mvsdio_data); +} diff --git a/arch/arm/mach-kirkwood/common.c b/arch/arm/mach-kirkwood/common.c index 401dac1..bac21a5 100644 --- a/arch/arm/mach-kirkwood/common.c +++ b/arch/arm/mach-kirkwood/common.c @@ -18,10 +18,10 @@ #include <linux/clk-provider.h> #include <linux/spinlock.h> #include <linux/mv643xx_i2c.h> +#include <linux/timex.h> +#include <linux/kexec.h> #include <net/dsa.h> #include <asm/page.h> -#include <asm/timex.h> -#include <asm/kexec.h> #include <asm/mach/map.h> #include <asm/mach/time.h> #include <mach/kirkwood.h> @@ -266,6 +266,7 @@ void __init kirkwood_clk_init(void) orion_clkdev_add("1", "pcie", pex1); orion_clkdev_add(NULL, "kirkwood-i2s", audio); orion_clkdev_add(NULL, MV64XXX_I2C_CTLR_NAME ".0", runit); + orion_clkdev_add(NULL, MV64XXX_I2C_CTLR_NAME ".1", runit); /* Marvell says runit is used by SPI, UART, NAND, TWSI, ..., * so should never be gated. @@ -425,7 +426,7 @@ void __init kirkwood_sdio_init(struct mvsdio_platform_data *mvsdio_data) /***************************************************************************** * SPI ****************************************************************************/ -void __init kirkwood_spi_init() +void __init kirkwood_spi_init(void) { orion_spi_init(SPI_PHYS_BASE); } @@ -646,8 +647,7 @@ void __init kirkwood_l2_init(void) void __init kirkwood_init(void) { - printk(KERN_INFO "Kirkwood: %s, TCLK=%d.\n", - kirkwood_id(), kirkwood_tclk); + pr_info("Kirkwood: %s, TCLK=%d.\n", kirkwood_id(), kirkwood_tclk); /* * Disable propagation of mbus errors to the CPU local bus, @@ -671,7 +671,7 @@ void __init kirkwood_init(void) kirkwood_xor1_init(); kirkwood_crypto_init(); -#ifdef CONFIG_KEXEC +#ifdef CONFIG_KEXEC kexec_reinit = kirkwood_enable_pcie; #endif } diff --git a/arch/arm/mach-kirkwood/common.h b/arch/arm/mach-kirkwood/common.h index bcffd7c..5ffa57f 100644 --- a/arch/arm/mach-kirkwood/common.h +++ b/arch/arm/mach-kirkwood/common.h @@ -47,7 +47,8 @@ void kirkwood_i2c_init(void); void kirkwood_uart0_init(void); void kirkwood_uart1_init(void); void kirkwood_nand_init(struct mtd_partition *parts, int nr_parts, int delay); -void kirkwood_nand_init_rnb(struct mtd_partition *parts, int nr_parts, int (*dev_ready)(struct mtd_info *)); +void kirkwood_nand_init_rnb(struct mtd_partition *parts, int nr_parts, + int (*dev_ready)(struct mtd_info *)); void kirkwood_audio_init(void); void kirkwood_restart(char, const char *); void kirkwood_clk_init(void); @@ -112,6 +113,40 @@ void km_kirkwood_init(void); static inline void km_kirkwood_init(void) {}; #endif +#ifdef CONFIG_MACH_MPLCEC4_DT +void mplcec4_init(void); +#else +static inline void mplcec4_init(void) {}; +#endif + +#if defined(CONFIG_MACH_INETSPACE_V2_DT) || \ + defined(CONFIG_MACH_NETSPACE_V2_DT) || \ + defined(CONFIG_MACH_NETSPACE_MAX_V2_DT) || \ + defined(CONFIG_MACH_NETSPACE_LITE_V2_DT) || \ + defined(CONFIG_MACH_NETSPACE_MINI_V2_DT) +void ns2_init(void); +#else +static inline void ns2_init(void) {}; +#endif + +#ifdef CONFIG_MACH_NSA310_DT +void nsa310_init(void); +#else +static inline void nsa310_init(void) {}; +#endif + +#ifdef CONFIG_MACH_OPENBLOCKS_A6_DT +void openblocks_a6_init(void); +#else +static inline void openblocks_a6_init(void) {}; +#endif + +#ifdef CONFIG_MACH_TOPKICK_DT +void usi_topkick_init(void); +#else +static inline void usi_topkick_init(void) {}; +#endif + /* early init functions not converted to fdt yet */ char *kirkwood_id(void); void kirkwood_l2_init(void); diff --git a/arch/arm/mach-kirkwood/cpuidle.c b/arch/arm/mach-kirkwood/cpuidle.c index 0f17109..f730467 100644 --- a/arch/arm/mach-kirkwood/cpuidle.c +++ b/arch/arm/mach-kirkwood/cpuidle.c @@ -64,7 +64,7 @@ static int kirkwood_init_cpuidle(void) cpuidle_register_driver(&kirkwood_idle_driver); if (cpuidle_register_device(device)) { - printk(KERN_ERR "kirkwood_init_cpuidle: Failed registering\n"); + pr_err("kirkwood_init_cpuidle: Failed registering\n"); return -EIO; } return 0; diff --git a/arch/arm/mach-kirkwood/dockstar-setup.c b/arch/arm/mach-kirkwood/dockstar-setup.c index 23dcb19..791a98f 100644 --- a/arch/arm/mach-kirkwood/dockstar-setup.c +++ b/arch/arm/mach-kirkwood/dockstar-setup.c @@ -93,7 +93,7 @@ static void __init dockstar_init(void) if (gpio_request(29, "USB Power Enable") != 0 || gpio_direction_output(29, 1) != 0) - printk(KERN_ERR "can't set up GPIO 29 (USB Power Enable)\n"); + pr_err("can't set up GPIO 29 (USB Power Enable)\n"); kirkwood_ehci_init(); kirkwood_ge00_init(&dockstar_ge00_data); diff --git a/arch/arm/mach-kirkwood/irq.c b/arch/arm/mach-kirkwood/irq.c index 8847035..2a97a2e 100644 --- a/arch/arm/mach-kirkwood/irq.c +++ b/arch/arm/mach-kirkwood/irq.c @@ -14,6 +14,7 @@ #include <mach/bridge-regs.h> #include <plat/orion-gpio.h> #include <plat/irq.h> +#include "common.h" static int __initdata gpio0_irqs[4] = { IRQ_KIRKWOOD_GPIO_LOW_0_7, diff --git a/arch/arm/mach-kirkwood/lacie_v2-common.c b/arch/arm/mach-kirkwood/lacie_v2-common.c index 285edab..4894959 100644 --- a/arch/arm/mach-kirkwood/lacie_v2-common.c +++ b/arch/arm/mach-kirkwood/lacie_v2-common.c @@ -19,6 +19,7 @@ #include <mach/irqs.h> #include <plat/time.h> #include "common.h" +#include "lacie_v2-common.h" /***************************************************************************** * 512KB SPI Flash on Boot Device (MACRONIX MX25L4005) diff --git a/arch/arm/mach-kirkwood/mpp.c b/arch/arm/mach-kirkwood/mpp.c index 0c6ad63..827cde4 100644 --- a/arch/arm/mach-kirkwood/mpp.c +++ b/arch/arm/mach-kirkwood/mpp.c @@ -30,8 +30,8 @@ static unsigned int __init kirkwood_variant(void) if (dev == MV88F6180_DEV_ID) return MPP_F6180_MASK; - printk(KERN_ERR "MPP setup: unknown kirkwood variant " - "(dev %#x rev %#x)\n", dev, rev); + pr_err("MPP setup: unknown kirkwood variant (dev %#x rev %#x)\n", + dev, rev); return 0; } diff --git a/arch/arm/mach-kirkwood/netspace_v2-setup.c b/arch/arm/mach-kirkwood/netspace_v2-setup.c index 88b0788b..728e86d 100644 --- a/arch/arm/mach-kirkwood/netspace_v2-setup.c +++ b/arch/arm/mach-kirkwood/netspace_v2-setup.c @@ -79,7 +79,7 @@ static struct platform_device netspace_v2_gpio_buttons = { .name = "gpio-keys", .id = -1, .dev = { - .platform_data = &netspace_v2_button_data, + .platform_data = &netspace_v2_button_data, }, }; @@ -211,7 +211,7 @@ static unsigned int netspace_v2_mpp_config[] __initdata = { MPP29_GPIO, /* Blue led (slow register) */ MPP30_GPIO, /* Blue led (command register) */ MPP31_GPIO, /* Board power off */ - MPP32_GPIO, /* Power button (0 = Released, 1 = Pushed) */ + MPP32_GPIO, /* Power button (0 = Released, 1 = Pushed) */ MPP33_GPO, /* Fan speed (bit 2) */ 0 }; diff --git a/arch/arm/mach-kirkwood/openrd-setup.c b/arch/arm/mach-kirkwood/openrd-setup.c index 134ef50..7e81e9b 100644 --- a/arch/arm/mach-kirkwood/openrd-setup.c +++ b/arch/arm/mach-kirkwood/openrd-setup.c @@ -121,14 +121,12 @@ static int __init uart1_mpp_config(void) kirkwood_mpp_conf(openrd_uart1_mpp_config); if (gpio_request(34, "SD_UART1_SEL")) { - printk(KERN_ERR "GPIO request failed for SD/UART1 selection" - ", gpio: 34\n"); + pr_err("GPIO request 34 failed for SD/UART1 selection\n"); return -EIO; } if (gpio_request(28, "RS232_RS485_SEL")) { - printk(KERN_ERR "GPIO request failed for RS232/RS485 selection" - ", gpio# 28\n"); + pr_err("GPIO request 28 failed for RS232/RS485 selection\n"); gpio_free(34); return -EIO; } @@ -185,15 +183,13 @@ static void __init openrd_init(void) if (uart1 <= 0) { if (uart1 < 0) - printk(KERN_ERR "Invalid kernel parameter to select " - "UART1. Defaulting to SD. ERROR CODE: %d\n", - uart1); + pr_err("Invalid kernel parameter to select UART1. Defaulting to SD. ERROR CODE: %d\n", + uart1); /* Select SD * Pin # 34: 0 => UART1, 1 => SD */ if (gpio_request(34, "SD_UART1_SEL")) { - printk(KERN_ERR "GPIO request failed for SD/UART1 " - "selection, gpio: 34\n"); + pr_err("GPIO request 34 failed for SD/UART1 selection\n"); } else { gpio_direction_output(34, 1); diff --git a/arch/arm/mach-kirkwood/pcie.c b/arch/arm/mach-kirkwood/pcie.c index ec54491..ef10264 100644 --- a/arch/arm/mach-kirkwood/pcie.c +++ b/arch/arm/mach-kirkwood/pcie.c @@ -26,7 +26,7 @@ static void kirkwood_enable_pcie_clk(const char *port) clk = clk_get_sys("pcie", port); if (IS_ERR(clk)) { - printk(KERN_ERR "PCIE clock %s missing\n", port); + pr_err("PCIE clock %s missing\n", port); return; } clk_prepare_enable(clk); @@ -168,7 +168,7 @@ static int __init kirkwood_pcie_setup(int nr, struct pci_sys_data *sys) return 0; index = pcie_port_map[nr]; - printk(KERN_INFO "PCI: bus%d uses PCIe port %d\n", sys->busnr, index); + pr_info("PCI: bus%d uses PCIe port %d\n", sys->busnr, index); pp = kzalloc(sizeof(*pp), GFP_KERNEL); if (!pp) @@ -186,7 +186,8 @@ static int __init kirkwood_pcie_setup(int nr, struct pci_sys_data *sys) case 1: kirkwood_enable_pcie_clk("1"); pcie1_ioresources_init(pp); - pci_ioremap_io(SZ_64K * sys->busnr, KIRKWOOD_PCIE1_IO_PHYS_BASE); + pci_ioremap_io(SZ_64K * sys->busnr, + KIRKWOOD_PCIE1_IO_PHYS_BASE); break; default: panic("PCIe setup: invalid controller %d", index); @@ -207,14 +208,19 @@ static int __init kirkwood_pcie_setup(int nr, struct pci_sys_data *sys) return 1; } +/* + * The root complex has a hardwired class of PCI_CLASS_MEMORY_OTHER, when it + * is operating as a root complex this needs to be switched to + * PCI_CLASS_BRIDGE_HOST or Linux will errantly try to process the BAR's on + * the device. Decoding setup is handled by the orion code. + */ static void __devinit rc_pci_fixup(struct pci_dev *dev) { - /* - * Prevent enumeration of root complex. - */ if (dev->bus->parent == NULL && dev->devfn == 0) { int i; + dev->class &= 0xff; + dev->class |= PCI_CLASS_BRIDGE_HOST << 8; for (i = 0; i < DEVICE_COUNT_RESOURCE; i++) { dev->resource[i].start = 0; dev->resource[i].end = 0; @@ -224,22 +230,6 @@ static void __devinit rc_pci_fixup(struct pci_dev *dev) } DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL, PCI_ANY_ID, rc_pci_fixup); -static struct pci_bus __init * -kirkwood_pcie_scan_bus(int nr, struct pci_sys_data *sys) -{ - struct pci_bus *bus; - - if (nr < num_pcie_ports) { - bus = pci_scan_root_bus(NULL, sys->busnr, &pcie_ops, sys, - &sys->resources); - } else { - bus = NULL; - BUG(); - } - - return bus; -} - static int __init kirkwood_pcie_map_irq(const struct pci_dev *dev, u8 slot, u8 pin) { @@ -251,19 +241,19 @@ static int __init kirkwood_pcie_map_irq(const struct pci_dev *dev, u8 slot, static struct hw_pci kirkwood_pci __initdata = { .setup = kirkwood_pcie_setup, - .scan = kirkwood_pcie_scan_bus, .map_irq = kirkwood_pcie_map_irq, + .ops = &pcie_ops, }; static void __init add_pcie_port(int index, void __iomem *base) { - printk(KERN_INFO "Kirkwood PCIe port %d: ", index); + pr_info("Kirkwood PCIe port %d: ", index); if (orion_pcie_link_up(base)) { - printk(KERN_INFO "link up\n"); + pr_info("link up\n"); pcie_port_map[num_pcie_ports++] = index; } else - printk(KERN_INFO "link down, ignoring\n"); + pr_info("link down, ignoring\n"); } void __init kirkwood_pcie_init(unsigned int portmask) diff --git a/arch/arm/mach-kirkwood/sheevaplug-setup.c b/arch/arm/mach-kirkwood/sheevaplug-setup.c index 28d0aba..8a17594 100644 --- a/arch/arm/mach-kirkwood/sheevaplug-setup.c +++ b/arch/arm/mach-kirkwood/sheevaplug-setup.c @@ -117,7 +117,7 @@ static void __init sheevaplug_init(void) if (gpio_request(29, "USB Power Enable") != 0 || gpio_direction_output(29, 1) != 0) - printk(KERN_ERR "can't set up GPIO 29 (USB Power Enable)\n"); + pr_err("can't set up GPIO 29 (USB Power Enable)\n"); kirkwood_ehci_init(); kirkwood_ge00_init(&sheevaplug_ge00_data); diff --git a/arch/arm/mach-kirkwood/t5325-setup.c b/arch/arm/mach-kirkwood/t5325-setup.c index bad738e..f2daf71 100644 --- a/arch/arm/mach-kirkwood/t5325-setup.c +++ b/arch/arm/mach-kirkwood/t5325-setup.c @@ -29,7 +29,7 @@ #include "common.h" #include "mpp.h" -struct mtd_partition hp_t5325_partitions[] = { +static struct mtd_partition hp_t5325_partitions[] = { { .name = "u-boot env", .size = SZ_64K, @@ -59,14 +59,14 @@ struct mtd_partition hp_t5325_partitions[] = { }, }; -const struct flash_platform_data hp_t5325_flash = { +static const struct flash_platform_data hp_t5325_flash = { .type = "mx25l8005", .name = "spi_flash", .parts = hp_t5325_partitions, .nr_parts = ARRAY_SIZE(hp_t5325_partitions), }; -struct spi_board_info __initdata hp_t5325_spi_slave_info[] = { +static struct spi_board_info __initdata hp_t5325_spi_slave_info[] = { { .modalias = "m25p80", .platform_data = &hp_t5325_flash, diff --git a/arch/arm/mach-kirkwood/ts41x-setup.c b/arch/arm/mach-kirkwood/ts41x-setup.c index 367a940..e4c6127 100644 --- a/arch/arm/mach-kirkwood/ts41x-setup.c +++ b/arch/arm/mach-kirkwood/ts41x-setup.c @@ -170,8 +170,7 @@ static int __init ts41x_pci_init(void) else kirkwood_pcie_init(KW_PCIE0); } - - return 0; + return 0; } subsys_initcall(ts41x_pci_init); diff --git a/arch/arm/mach-kirkwood/tsx1x-common.c b/arch/arm/mach-kirkwood/tsx1x-common.c index 8943ede..cec87ce 100644 --- a/arch/arm/mach-kirkwood/tsx1x-common.c +++ b/arch/arm/mach-kirkwood/tsx1x-common.c @@ -7,6 +7,7 @@ #include <linux/serial_reg.h> #include <mach/kirkwood.h> #include "common.h" +#include "tsx1x-common.h" /* * QNAP TS-x1x Boards flash @@ -29,7 +30,7 @@ * ***************************************************************************/ -struct mtd_partition qnap_tsx1x_partitions[] = { +static struct mtd_partition qnap_tsx1x_partitions[] = { { .name = "U-Boot", .size = 0x00080000, @@ -58,14 +59,14 @@ struct mtd_partition qnap_tsx1x_partitions[] = { }, }; -const struct flash_platform_data qnap_tsx1x_flash = { +static const struct flash_platform_data qnap_tsx1x_flash = { .type = "m25p128", .name = "spi_flash", .parts = qnap_tsx1x_partitions, .nr_parts = ARRAY_SIZE(qnap_tsx1x_partitions), }; -struct spi_board_info __initdata qnap_tsx1x_spi_slave_info[] = { +static struct spi_board_info __initdata qnap_tsx1x_spi_slave_info[] = { { .modalias = "m25p80", .platform_data = &qnap_tsx1x_flash, |