diff options
Diffstat (limited to 'arch/arm/mach-imx/mach-mx27ads.c')
| -rw-r--r-- | arch/arm/mach-imx/mach-mx27ads.c | 357 |
1 files changed, 357 insertions, 0 deletions
diff --git a/arch/arm/mach-imx/mach-mx27ads.c b/arch/arm/mach-imx/mach-mx27ads.c new file mode 100644 index 0000000..9c77da9 --- /dev/null +++ b/arch/arm/mach-imx/mach-mx27ads.c @@ -0,0 +1,357 @@ +/* + * Copyright (C) 2000 Deep Blue Solutions Ltd + * Copyright (C) 2002 Shane Nay (shane@minirl.com) + * Copyright 2006-2007 Freescale Semiconductor, Inc. All Rights Reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include <linux/platform_device.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/map.h> +#include <linux/mtd/partitions.h> +#include <linux/mtd/physmap.h> +#include <linux/i2c.h> +#include <linux/irq.h> +#include <mach/common.h> +#include <mach/hardware.h> +#include <asm/mach-types.h> +#include <asm/mach/arch.h> +#include <asm/mach/time.h> +#include <asm/mach/map.h> +#include <mach/gpio.h> +#include <mach/iomux-mx27.h> +#include <mach/mxc_nand.h> +#include <mach/imxfb.h> +#include <mach/mmc.h> + +#include "devices-imx27.h" +#include "devices.h" + +/* + * Base address of PBC controller, CS4 + */ +#define PBC_BASE_ADDRESS 0xf4300000 +#define PBC_REG_ADDR(offset) (void __force __iomem *) \ + (PBC_BASE_ADDRESS + (offset)) + +/* When the PBC address connection is fixed in h/w, defined as 1 */ +#define PBC_ADDR_SH 0 + +/* Offsets for the PBC Controller register */ +/* + * PBC Board version register offset + */ +#define PBC_VERSION_REG PBC_REG_ADDR(0x00000 >> PBC_ADDR_SH) +/* + * PBC Board control register 1 set address. + */ +#define PBC_BCTRL1_SET_REG PBC_REG_ADDR(0x00008 >> PBC_ADDR_SH) +/* + * PBC Board control register 1 clear address. + */ +#define PBC_BCTRL1_CLEAR_REG PBC_REG_ADDR(0x0000C >> PBC_ADDR_SH) + +/* PBC Board Control Register 1 bit definitions */ +#define PBC_BCTRL1_LCDON 0x0800 /* Enable the LCD */ + +/* to determine the correct external crystal reference */ +#define CKIH_27MHZ_BIT_SET (1 << 3) + +static unsigned int mx27ads_pins[] = { + /* UART0 */ + PE12_PF_UART1_TXD, + PE13_PF_UART1_RXD, + PE14_PF_UART1_CTS, + PE15_PF_UART1_RTS, + /* UART1 */ + PE3_PF_UART2_CTS, + PE4_PF_UART2_RTS, + PE6_PF_UART2_TXD, + PE7_PF_UART2_RXD, + /* UART2 */ + PE8_PF_UART3_TXD, + PE9_PF_UART3_RXD, + PE10_PF_UART3_CTS, + PE11_PF_UART3_RTS, + /* UART3 */ + PB26_AF_UART4_RTS, + PB28_AF_UART4_TXD, + PB29_AF_UART4_CTS, + PB31_AF_UART4_RXD, + /* UART4 */ + PB18_AF_UART5_TXD, + PB19_AF_UART5_RXD, + PB20_AF_UART5_CTS, + PB21_AF_UART5_RTS, + /* UART5 */ + PB10_AF_UART6_TXD, + PB12_AF_UART6_CTS, + PB11_AF_UART6_RXD, + PB13_AF_UART6_RTS, + /* FEC */ + PD0_AIN_FEC_TXD0, + PD1_AIN_FEC_TXD1, + PD2_AIN_FEC_TXD2, + PD3_AIN_FEC_TXD3, + PD4_AOUT_FEC_RX_ER, + PD5_AOUT_FEC_RXD1, + PD6_AOUT_FEC_RXD2, + PD7_AOUT_FEC_RXD3, + PD8_AF_FEC_MDIO, + PD9_AIN_FEC_MDC, + PD10_AOUT_FEC_CRS, + PD11_AOUT_FEC_TX_CLK, + PD12_AOUT_FEC_RXD0, + PD13_AOUT_FEC_RX_DV, + PD14_AOUT_FEC_RX_CLK, + PD15_AOUT_FEC_COL, + PD16_AIN_FEC_TX_ER, + PF23_AIN_FEC_TX_EN, + /* I2C2 */ + PC5_PF_I2C2_SDA, + PC6_PF_I2C2_SCL, + /* FB */ + PA5_PF_LSCLK, + PA6_PF_LD0, + PA7_PF_LD1, + PA8_PF_LD2, + PA9_PF_LD3, + PA10_PF_LD4, + PA11_PF_LD5, + PA12_PF_LD6, + PA13_PF_LD7, + PA14_PF_LD8, + PA15_PF_LD9, + PA16_PF_LD10, + PA17_PF_LD11, + PA18_PF_LD12, + PA19_PF_LD13, + PA20_PF_LD14, + PA21_PF_LD15, + PA22_PF_LD16, + PA23_PF_LD17, + PA24_PF_REV, + PA25_PF_CLS, + PA26_PF_PS, + PA27_PF_SPL_SPR, + PA28_PF_HSYNC, + PA29_PF_VSYNC, + PA30_PF_CONTRAST, + PA31_PF_OE_ACD, + /* OWIRE */ + PE16_AF_OWIRE, + /* SDHC1*/ + PE18_PF_SD1_D0, + PE19_PF_SD1_D1, + PE20_PF_SD1_D2, + PE21_PF_SD1_D3, + PE22_PF_SD1_CMD, + PE23_PF_SD1_CLK, + /* SDHC2*/ + PB4_PF_SD2_D0, + PB5_PF_SD2_D1, + PB6_PF_SD2_D2, + PB7_PF_SD2_D3, + PB8_PF_SD2_CMD, + PB9_PF_SD2_CLK, +}; + +static const struct mxc_nand_platform_data +mx27ads_nand_board_info __initconst = { + .width = 1, + .hw_ecc = 1, +}; + +/* ADS's NOR flash */ +static struct physmap_flash_data mx27ads_flash_data = { + .width = 2, +}; + +static struct resource mx27ads_flash_resource = { + .start = 0xc0000000, + .end = 0xc0000000 + 0x02000000 - 1, + .flags = IORESOURCE_MEM, + +}; + +static struct platform_device mx27ads_nor_mtd_device = { + .name = "physmap-flash", + .id = 0, + .dev = { + .platform_data = &mx27ads_flash_data, + }, + .num_resources = 1, + .resource = &mx27ads_flash_resource, +}; + +static const struct imxi2c_platform_data mx27ads_i2c1_data __initconst = { + .bitrate = 100000, +}; + +static struct i2c_board_info mx27ads_i2c_devices[] = { +}; + +void lcd_power(int on) +{ + if (on) + __raw_writew(PBC_BCTRL1_LCDON, PBC_BCTRL1_SET_REG); + else + __raw_writew(PBC_BCTRL1_LCDON, PBC_BCTRL1_CLEAR_REG); +} + +static struct imx_fb_videomode mx27ads_modes[] = { + { + .mode = { + .name = "Sharp-LQ035Q7", + .refresh = 60, + .xres = 240, + .yres = 320, + .pixclock = 188679, /* in ps (5.3MHz) */ + .hsync_len = 1, + .left_margin = 9, + .right_margin = 16, + .vsync_len = 1, + .upper_margin = 7, + .lower_margin = 9, + }, + .bpp = 16, + .pcr = 0xFB008BC0, + }, +}; + +static struct imx_fb_platform_data mx27ads_fb_data = { + .mode = mx27ads_modes, + .num_modes = ARRAY_SIZE(mx27ads_modes), + + /* + * - HSYNC active high + * - VSYNC active high + * - clk notenabled while idle + * - clock inverted + * - data not inverted + * - data enable low active + * - enable sharp mode + */ + .pwmr = 0x00A903FF, + .lscr1 = 0x00120300, + .dmacr = 0x00020010, + + .lcd_power = lcd_power, +}; + +static int mx27ads_sdhc1_init(struct device *dev, irq_handler_t detect_irq, + void *data) +{ + return request_irq(IRQ_GPIOE(21), detect_irq, IRQF_TRIGGER_RISING, + "sdhc1-card-detect", data); +} + +static int mx27ads_sdhc2_init(struct device *dev, irq_handler_t detect_irq, + void *data) +{ + return request_irq(IRQ_GPIOB(7), detect_irq, IRQF_TRIGGER_RISING, + "sdhc2-card-detect", data); +} + +static void mx27ads_sdhc1_exit(struct device *dev, void *data) +{ + free_irq(IRQ_GPIOE(21), data); +} + +static void mx27ads_sdhc2_exit(struct device *dev, void *data) +{ + free_irq(IRQ_GPIOB(7), data); +} + +static struct imxmmc_platform_data sdhc1_pdata = { + .init = mx27ads_sdhc1_init, + .exit = mx27ads_sdhc1_exit, +}; + +static struct imxmmc_platform_data sdhc2_pdata = { + .init = mx27ads_sdhc2_init, + .exit = mx27ads_sdhc2_exit, +}; + +static struct platform_device *platform_devices[] __initdata = { + &mx27ads_nor_mtd_device, + &mxc_fec_device, + &mxc_w1_master_device, +}; + +static const struct imxuart_platform_data uart_pdata __initconst = { + .flags = IMXUART_HAVE_RTSCTS, +}; + +static void __init mx27ads_board_init(void) +{ + mxc_gpio_setup_multiple_pins(mx27ads_pins, ARRAY_SIZE(mx27ads_pins), + "mx27ads"); + + imx27_add_imx_uart0(&uart_pdata); + imx27_add_imx_uart1(&uart_pdata); + imx27_add_imx_uart2(&uart_pdata); + imx27_add_imx_uart3(&uart_pdata); + imx27_add_imx_uart4(&uart_pdata); + imx27_add_imx_uart5(&uart_pdata); + imx27_add_mxc_nand(&mx27ads_nand_board_info); + + /* only the i2c master 1 is used on this CPU card */ + i2c_register_board_info(1, mx27ads_i2c_devices, + ARRAY_SIZE(mx27ads_i2c_devices)); + imx27_add_i2c_imx1(&mx27ads_i2c1_data); + mxc_register_device(&mxc_fb_device, &mx27ads_fb_data); + mxc_register_device(&mxc_sdhc_device0, &sdhc1_pdata); + mxc_register_device(&mxc_sdhc_device1, &sdhc2_pdata); + + platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices)); +} + +static void __init mx27ads_timer_init(void) +{ + unsigned long fref = 26000000; + + if ((__raw_readw(PBC_VERSION_REG) & CKIH_27MHZ_BIT_SET) == 0) + fref = 27000000; + + mx27_clocks_init(fref); +} + +static struct sys_timer mx27ads_timer = { + .init = mx27ads_timer_init, +}; + +static struct map_desc mx27ads_io_desc[] __initdata = { + { + .virtual = PBC_BASE_ADDRESS, + .pfn = __phys_to_pfn(MX27_CS4_BASE_ADDR), + .length = SZ_1M, + .type = MT_DEVICE, + }, +}; + +static void __init mx27ads_map_io(void) +{ + mx27_map_io(); + iotable_init(mx27ads_io_desc, ARRAY_SIZE(mx27ads_io_desc)); +} + +MACHINE_START(MX27ADS, "Freescale i.MX27ADS") + /* maintainer: Freescale Semiconductor, Inc. */ + .phys_io = MX27_AIPI_BASE_ADDR, + .io_pg_offst = ((MX27_AIPI_BASE_ADDR_VIRT) >> 18) & 0xfffc, + .boot_params = MX27_PHYS_OFFSET + 0x100, + .map_io = mx27ads_map_io, + .init_irq = mx27_init_irq, + .init_machine = mx27ads_board_init, + .timer = &mx27ads_timer, +MACHINE_END |
