15 files changed, 636 insertions, 172 deletions

diff --git a/arch/arm/mach-ep93xx/adssphere.c b/arch/arm/mach-ep93xx/adssphere.c
index 3fbd9b0..caf6d51 100644
--- a/arch/arm/mach-ep93xx/adssphere.c
+++ b/arch/arm/mach-ep93xx/adssphere.c
@@ -12,18 +12,15 @@
 
 #include <linux/kernel.h>
 #include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/sched.h>
-#include <linux/interrupt.h>
-#include <linux/ioport.h>
-#include <linux/mtd/physmap.h>
 #include <linux/platform_device.h>
-#include <linux/io.h>
-#include <linux/i2c.h>
+#include <linux/mtd/physmap.h>
+
 #include <mach/hardware.h>
+
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 
+
 static struct physmap_flash_data adssphere_flash_data = {
 	.width		= 4,
 };
diff --git a/arch/arm/mach-ep93xx/clock.c b/arch/arm/mach-ep93xx/clock.c
index 6c4c163..dda19cd7 100644
--- a/arch/arm/mach-ep93xx/clock.c
+++ b/arch/arm/mach-ep93xx/clock.c
@@ -22,48 +22,39 @@
 #include <mach/hardware.h>
 
 
-/*
- * The EP93xx has two external crystal oscillators.  To generate the
- * required high-frequency clocks, the processor uses two phase-locked-
- * loops (PLLs) to multiply the incoming external clock signal to much
- * higher frequencies that are then divided down by programmable dividers
- * to produce the needed clocks.  The PLLs operate independently of one
- * another.
- */
-#define EP93XX_EXT_CLK_RATE	14745600
-#define EP93XX_EXT_RTC_RATE	32768
-
-
 struct clk {
 	unsigned long	rate;
 	int		users;
 	int		sw_locked;
-	u32		enable_reg;
+	void __iomem	*enable_reg;
 	u32		enable_mask;
 
 	unsigned long	(*get_rate)(struct clk *clk);
+	int		(*set_rate)(struct clk *clk, unsigned long rate);
 };
 
 
 static unsigned long get_uart_rate(struct clk *clk);
 
+static int set_keytchclk_rate(struct clk *clk, unsigned long rate);
+static int set_div_rate(struct clk *clk, unsigned long rate);
 
 static struct clk clk_uart1 = {
 	.sw_locked	= 1,
-	.enable_reg	= EP93XX_SYSCON_DEVICE_CONFIG,
-	.enable_mask	= EP93XX_SYSCON_DEVICE_CONFIG_U1EN,
+	.enable_reg	= EP93XX_SYSCON_DEVCFG,
+	.enable_mask	= EP93XX_SYSCON_DEVCFG_U1EN,
 	.get_rate	= get_uart_rate,
 };
 static struct clk clk_uart2 = {
 	.sw_locked	= 1,
-	.enable_reg	= EP93XX_SYSCON_DEVICE_CONFIG,
-	.enable_mask	= EP93XX_SYSCON_DEVICE_CONFIG_U2EN,
+	.enable_reg	= EP93XX_SYSCON_DEVCFG,
+	.enable_mask	= EP93XX_SYSCON_DEVCFG_U2EN,
 	.get_rate	= get_uart_rate,
 };
 static struct clk clk_uart3 = {
 	.sw_locked	= 1,
-	.enable_reg	= EP93XX_SYSCON_DEVICE_CONFIG,
-	.enable_mask	= EP93XX_SYSCON_DEVICE_CONFIG_U3EN,
+	.enable_reg	= EP93XX_SYSCON_DEVCFG,
+	.enable_mask	= EP93XX_SYSCON_DEVCFG_U3EN,
 	.get_rate	= get_uart_rate,
 };
 static struct clk clk_pll1;
@@ -75,6 +66,22 @@ static struct clk clk_usb_host = {
 	.enable_reg	= EP93XX_SYSCON_PWRCNT,
 	.enable_mask	= EP93XX_SYSCON_PWRCNT_USH_EN,
 };
+static struct clk clk_keypad = {
+	.sw_locked	= 1,
+	.enable_reg	= EP93XX_SYSCON_KEYTCHCLKDIV,
+	.enable_mask	= EP93XX_SYSCON_KEYTCHCLKDIV_KEN,
+	.set_rate	= set_keytchclk_rate,
+};
+static struct clk clk_pwm = {
+	.rate		= EP93XX_EXT_CLK_RATE,
+};
+
+static struct clk clk_video = {
+	.sw_locked	= 1,
+	.enable_reg     = EP93XX_SYSCON_VIDCLKDIV,
+	.enable_mask    = EP93XX_SYSCON_CLKDIV_ENABLE,
+	.set_rate	= set_div_rate,
+};
 
 /* DMA Clocks */
 static struct clk clk_m2p0 = {
@@ -130,27 +137,30 @@ static struct clk clk_m2m1 = {
 	{ .dev_id = dev, .con_id = con, .clk = ck }
 
 static struct clk_lookup clocks[] = {
-	INIT_CK("apb:uart1", NULL, &clk_uart1),
-	INIT_CK("apb:uart2", NULL, &clk_uart2),
-	INIT_CK("apb:uart3", NULL, &clk_uart3),
-	INIT_CK(NULL, "pll1", &clk_pll1),
-	INIT_CK(NULL, "fclk", &clk_f),
-	INIT_CK(NULL, "hclk", &clk_h),
-	INIT_CK(NULL, "pclk", &clk_p),
-	INIT_CK(NULL, "pll2", &clk_pll2),
-	INIT_CK("ep93xx-ohci", NULL, &clk_usb_host),
-	INIT_CK(NULL, "m2p0", &clk_m2p0),
-	INIT_CK(NULL, "m2p1", &clk_m2p1),
-	INIT_CK(NULL, "m2p2", &clk_m2p2),
-	INIT_CK(NULL, "m2p3", &clk_m2p3),
-	INIT_CK(NULL, "m2p4", &clk_m2p4),
-	INIT_CK(NULL, "m2p5", &clk_m2p5),
-	INIT_CK(NULL, "m2p6", &clk_m2p6),
-	INIT_CK(NULL, "m2p7", &clk_m2p7),
-	INIT_CK(NULL, "m2p8", &clk_m2p8),
-	INIT_CK(NULL, "m2p9", &clk_m2p9),
-	INIT_CK(NULL, "m2m0", &clk_m2m0),
-	INIT_CK(NULL, "m2m1", &clk_m2m1),
+	INIT_CK("apb:uart1",		NULL,		&clk_uart1),
+	INIT_CK("apb:uart2",		NULL,		&clk_uart2),
+	INIT_CK("apb:uart3",		NULL,		&clk_uart3),
+	INIT_CK(NULL,			"pll1",		&clk_pll1),
+	INIT_CK(NULL,			"fclk",		&clk_f),
+	INIT_CK(NULL,			"hclk",		&clk_h),
+	INIT_CK(NULL,			"pclk",		&clk_p),
+	INIT_CK(NULL,			"pll2",		&clk_pll2),
+	INIT_CK("ep93xx-ohci",		NULL,		&clk_usb_host),
+	INIT_CK("ep93xx-keypad",	NULL,		&clk_keypad),
+	INIT_CK("ep93xx-fb",		NULL,		&clk_video),
+	INIT_CK(NULL,			"pwm_clk",	&clk_pwm),
+	INIT_CK(NULL,			"m2p0",		&clk_m2p0),
+	INIT_CK(NULL,			"m2p1",		&clk_m2p1),
+	INIT_CK(NULL,			"m2p2",		&clk_m2p2),
+	INIT_CK(NULL,			"m2p3",		&clk_m2p3),
+	INIT_CK(NULL,			"m2p4",		&clk_m2p4),
+	INIT_CK(NULL,			"m2p5",		&clk_m2p5),
+	INIT_CK(NULL,			"m2p6",		&clk_m2p6),
+	INIT_CK(NULL,			"m2p7",		&clk_m2p7),
+	INIT_CK(NULL,			"m2p8",		&clk_m2p8),
+	INIT_CK(NULL,			"m2p9",		&clk_m2p9),
+	INIT_CK(NULL,			"m2m0",		&clk_m2m0),
+	INIT_CK(NULL,			"m2m1",		&clk_m2m1),
 };
 
 
@@ -160,9 +170,11 @@ int clk_enable(struct clk *clk)
 		u32 value;
 
 		value = __raw_readl(clk->enable_reg);
+		value |= clk->enable_mask;
 		if (clk->sw_locked)
-			__raw_writel(0xaa, EP93XX_SYSCON_SWLOCK);
-		__raw_writel(value | clk->enable_mask, clk->enable_reg);
+			ep93xx_syscon_swlocked_write(value, clk->enable_reg);
+		else
+			__raw_writel(value, clk->enable_reg);
 	}
 
 	return 0;
@@ -175,9 +187,11 @@ void clk_disable(struct clk *clk)
 		u32 value;
 
 		value = __raw_readl(clk->enable_reg);
+		value &= ~clk->enable_mask;
 		if (clk->sw_locked)
-			__raw_writel(0xaa, EP93XX_SYSCON_SWLOCK);
-		__raw_writel(value & ~clk->enable_mask, clk->enable_reg);
+			ep93xx_syscon_swlocked_write(value, clk->enable_reg);
+		else
+			__raw_writel(value, clk->enable_reg);
 	}
 }
 EXPORT_SYMBOL(clk_disable);
@@ -202,6 +216,121 @@ unsigned long clk_get_rate(struct clk *clk)
 }
 EXPORT_SYMBOL(clk_get_rate);
 
+static int set_keytchclk_rate(struct clk *clk, unsigned long rate)
+{
+	u32 val;
+	u32 div_bit;
+
+	val = __raw_readl(clk->enable_reg);
+
+	/*
+	 * The Key Matrix and ADC clocks are configured using the same
+	 * System Controller register.  The clock used will be either
+	 * 1/4 or 1/16 the external clock rate depending on the
+	 * EP93XX_SYSCON_KEYTCHCLKDIV_KDIV/EP93XX_SYSCON_KEYTCHCLKDIV_ADIV
+	 * bit being set or cleared.
+	 */
+	div_bit = clk->enable_mask >> 15;
+
+	if (rate == EP93XX_KEYTCHCLK_DIV4)
+		val |= div_bit;
+	else if (rate == EP93XX_KEYTCHCLK_DIV16)
+		val &= ~div_bit;
+	else
+		return -EINVAL;
+
+	ep93xx_syscon_swlocked_write(val, clk->enable_reg);
+	clk->rate = rate;
+	return 0;
+}
+
+static unsigned long calc_clk_div(unsigned long rate, int *psel, int *esel,
+				  int *pdiv, int *div)
+{
+	unsigned long max_rate, best_rate = 0,
+		actual_rate = 0, mclk_rate = 0, rate_err = -1;
+	int i, found = 0, __div = 0, __pdiv = 0;
+
+	/* Don't exceed the maximum rate */
+	max_rate = max(max(clk_pll1.rate / 4, clk_pll2.rate / 4),
+		       (unsigned long)EP93XX_EXT_CLK_RATE / 4);
+	rate = min(rate, max_rate);
+
+	/*
+	 * Try the two pll's and the external clock
+	 * Because the valid predividers are 2, 2.5 and 3, we multiply
+	 * all the clocks by 2 to avoid floating point math.
+	 *
+	 * This is based on the algorithm in the ep93xx raster guide:
+	 * http://be-a-maverick.com/en/pubs/appNote/AN269REV1.pdf
+	 *
+	 */
+	for (i = 0; i < 3; i++) {
+		if (i == 0)
+			mclk_rate = EP93XX_EXT_CLK_RATE * 2;
+		else if (i == 1)
+			mclk_rate = clk_pll1.rate * 2;
+		else if (i == 2)
+			mclk_rate = clk_pll2.rate * 2;
+
+		/* Try each predivider value */
+		for (__pdiv = 4; __pdiv <= 6; __pdiv++) {
+			__div = mclk_rate / (rate * __pdiv);
+			if (__div < 2 || __div > 127)
+				continue;
+
+			actual_rate = mclk_rate / (__pdiv * __div);
+
+			if (!found || abs(actual_rate - rate) < rate_err) {
+				*pdiv = __pdiv - 3;
+				*div = __div;
+				*psel = (i == 2);
+				*esel = (i != 0);
+				best_rate = actual_rate;
+				rate_err = abs(actual_rate - rate);
+				found = 1;
+			}
+		}
+	}
+
+	if (!found)
+		return 0;
+
+	return best_rate;
+}
+
+static int set_div_rate(struct clk *clk, unsigned long rate)
+{
+	unsigned long actual_rate;
+	int psel = 0, esel = 0, pdiv = 0, div = 0;
+	u32 val;
+
+	actual_rate = calc_clk_div(rate, &psel, &esel, &pdiv, &div);
+	if (actual_rate == 0)
+		return -EINVAL;
+	clk->rate = actual_rate;
+
+	/* Clear the esel, psel, pdiv and div bits */
+	val = __raw_readl(clk->enable_reg);
+	val &= ~0x7fff;
+
+	/* Set the new esel, psel, pdiv and div bits for the new clock rate */
+	val |= (esel ? EP93XX_SYSCON_CLKDIV_ESEL : 0) |
+		(psel ? EP93XX_SYSCON_CLKDIV_PSEL : 0) |
+		(pdiv << EP93XX_SYSCON_CLKDIV_PDIV_SHIFT) | div;
+	ep93xx_syscon_swlocked_write(val, clk->enable_reg);
+	return 0;
+}
+
+int clk_set_rate(struct clk *clk, unsigned long rate)
+{
+	if (clk->set_rate)
+		return clk->set_rate(clk, rate);
+
+	return -EINVAL;
+}
+EXPORT_SYMBOL(clk_set_rate);
+
 
 static char fclk_divisors[] = { 1, 2, 4, 8, 16, 1, 1, 1 };
 static char hclk_divisors[] = { 1, 2, 4, 5, 6, 8, 16, 32 };
diff --git a/arch/arm/mach-ep93xx/core.c b/arch/arm/mach-ep93xx/core.c
index 204dc5c..f7ebed9 100644
--- a/arch/arm/mach-ep93xx/core.c
+++ b/arch/arm/mach-ep93xx/core.c
@@ -16,40 +16,25 @@
 
 #include <linux/kernel.h>
 #include <linux/init.h>
-#include <linux/spinlock.h>
-#include <linux/sched.h>
+#include <linux/platform_device.h>
 #include <linux/interrupt.h>
-#include <linux/serial.h>
-#include <linux/tty.h>
-#include <linux/bitops.h>
-#include <linux/serial_8250.h>
-#include <linux/serial_core.h>
-#include <linux/device.h>
-#include <linux/mm.h>
 #include <linux/dma-mapping.h>
-#include <linux/time.h>
 #include <linux/timex.h>
-#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/gpio.h>
+#include <linux/leds.h>
 #include <linux/termios.h>
 #include <linux/amba/bus.h>
 #include <linux/amba/serial.h>
-#include <linux/io.h>
 #include <linux/i2c.h>
 #include <linux/i2c-gpio.h>
 
-#include <asm/types.h>
-#include <asm/setup.h>
-#include <asm/memory.h>
 #include <mach/hardware.h>
-#include <asm/irq.h>
-#include <asm/system.h>
-#include <asm/tlbflush.h>
-#include <asm/pgtable.h>
+#include <mach/fb.h>
 
 #include <asm/mach/map.h>
 #include <asm/mach/time.h>
 #include <asm/mach/irq.h>
-#include <mach/gpio.h>
 
 #include <asm/hardware/vic.h>
 
@@ -98,7 +83,7 @@ void __init ep93xx_map_io(void)
  */
 static unsigned int last_jiffy_time;
 
-#define TIMER4_TICKS_PER_JIFFY		((CLOCK_TICK_RATE + (HZ/2)) / HZ)
+#define TIMER4_TICKS_PER_JIFFY		DIV_ROUND_CLOSEST(CLOCK_TICK_RATE, HZ)
 
 static irqreturn_t ep93xx_timer_interrupt(int irq, void *dev_id)
 {
@@ -362,8 +347,8 @@ void __init ep93xx_init_irq(void)
 {
 	int gpio_irq;
 
-	vic_init((void *)EP93XX_VIC1_BASE, 0, EP93XX_VIC1_VALID_IRQ_MASK, 0);
-	vic_init((void *)EP93XX_VIC2_BASE, 32, EP93XX_VIC2_VALID_IRQ_MASK, 0);
+	vic_init(EP93XX_VIC1_BASE, 0, EP93XX_VIC1_VALID_IRQ_MASK, 0);
+	vic_init(EP93XX_VIC2_BASE, 32, EP93XX_VIC2_VALID_IRQ_MASK, 0);
 
 	for (gpio_irq = gpio_to_irq(0);
 	     gpio_irq <= gpio_to_irq(EP93XX_GPIO_LINE_MAX_IRQ); ++gpio_irq) {
@@ -385,6 +370,47 @@ void __init ep93xx_init_irq(void)
 
 
 /*************************************************************************
+ * EP93xx System Controller Software Locked register handling
+ *************************************************************************/
+
+/*
+ * syscon_swlock prevents anything else from writing to the syscon
+ * block while a software locked register is being written.
+ */
+static DEFINE_SPINLOCK(syscon_swlock);
+
+void ep93xx_syscon_swlocked_write(unsigned int val, void __iomem *reg)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&syscon_swlock, flags);
+
+	__raw_writel(0xaa, EP93XX_SYSCON_SWLOCK);
+	__raw_writel(val, reg);
+
+	spin_unlock_irqrestore(&syscon_swlock, flags);
+}
+EXPORT_SYMBOL(ep93xx_syscon_swlocked_write);
+
+void ep93xx_devcfg_set_clear(unsigned int set_bits, unsigned int clear_bits)
+{
+	unsigned long flags;
+	unsigned int val;
+
+	spin_lock_irqsave(&syscon_swlock, flags);
+
+	val = __raw_readl(EP93XX_SYSCON_DEVCFG);
+	val |= set_bits;
+	val &= ~clear_bits;
+	__raw_writel(0xaa, EP93XX_SYSCON_SWLOCK);
+	__raw_writel(val, EP93XX_SYSCON_DEVCFG);
+
+	spin_unlock_irqrestore(&syscon_swlock, flags);
+}
+EXPORT_SYMBOL(ep93xx_devcfg_set_clear);
+
+
+/*************************************************************************
  * EP93xx peripheral handling
  *************************************************************************/
 #define EP93XX_UART_MCR_OFFSET		(0x0100)
@@ -517,10 +543,8 @@ static struct platform_device ep93xx_eth_device = {
 
 void __init ep93xx_register_eth(struct ep93xx_eth_data *data, int copy_addr)
 {
-	if (copy_addr) {
-		memcpy(data->dev_addr,
-			(void *)(EP93XX_ETHERNET_BASE + 0x50), 6);
-	}
+	if (copy_addr)
+		memcpy_fromio(data->dev_addr, EP93XX_ETHERNET_BASE + 0x50, 6);
 
 	ep93xx_eth_data = *data;
 	platform_device_register(&ep93xx_eth_device);
@@ -546,19 +570,156 @@ void __init ep93xx_register_i2c(struct i2c_board_info *devices, int num)
 	platform_device_register(&ep93xx_i2c_device);
 }
 
+
+/*************************************************************************
+ * EP93xx LEDs
+ *************************************************************************/
+static struct gpio_led ep93xx_led_pins[] = {
+	{
+		.name			= "platform:grled",
+		.gpio			= EP93XX_GPIO_LINE_GRLED,
+	}, {
+		.name			= "platform:rdled",
+		.gpio			= EP93XX_GPIO_LINE_RDLED,
+	},
+};
+
+static struct gpio_led_platform_data ep93xx_led_data = {
+	.num_leds	= ARRAY_SIZE(ep93xx_led_pins),
+	.leds		= ep93xx_led_pins,
+};
+
+static struct platform_device ep93xx_leds = {
+	.name		= "leds-gpio",
+	.id		= -1,
+	.dev		= {
+		.platform_data	= &ep93xx_led_data,
+	},
+};
+
+
+/*************************************************************************
+ * EP93xx pwm peripheral handling
+ *************************************************************************/
+static struct resource ep93xx_pwm0_resource[] = {
+	{
+		.start	= EP93XX_PWM_PHYS_BASE,
+		.end	= EP93XX_PWM_PHYS_BASE + 0x10 - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+};
+
+static struct platform_device ep93xx_pwm0_device = {
+	.name		= "ep93xx-pwm",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(ep93xx_pwm0_resource),
+	.resource	= ep93xx_pwm0_resource,
+};
+
+static struct resource ep93xx_pwm1_resource[] = {
+	{
+		.start	= EP93XX_PWM_PHYS_BASE + 0x20,
+		.end	= EP93XX_PWM_PHYS_BASE + 0x30 - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+};
+
+static struct platform_device ep93xx_pwm1_device = {
+	.name		= "ep93xx-pwm",
+	.id		= 1,
+	.num_resources	= ARRAY_SIZE(ep93xx_pwm1_resource),
+	.resource	= ep93xx_pwm1_resource,
+};
+
+void __init ep93xx_register_pwm(int pwm0, int pwm1)
+{
+	if (pwm0)
+		platform_device_register(&ep93xx_pwm0_device);
+
+	/* NOTE: EP9307 does not have PWMOUT1 (pin EGPIO14) */
+	if (pwm1)
+		platform_device_register(&ep93xx_pwm1_device);
+}
+
+int ep93xx_pwm_acquire_gpio(struct platform_device *pdev)
+{
+	int err;
+
+	if (pdev->id == 0) {
+		err = 0;
+	} else if (pdev->id == 1) {
+		err = gpio_request(EP93XX_GPIO_LINE_EGPIO14,
+				   dev_name(&pdev->dev));
+		if (err)
+			return err;
+		err = gpio_direction_output(EP93XX_GPIO_LINE_EGPIO14, 0);
+		if (err)
+			goto fail;
+
+		/* PWM 1 output on EGPIO[14] */
+		ep93xx_devcfg_set_bits(EP93XX_SYSCON_DEVCFG_PONG);
+	} else {
+		err = -ENODEV;
+	}
+
+	return err;
+
+fail:
+	gpio_free(EP93XX_GPIO_LINE_EGPIO14);
+	return err;
+}
+EXPORT_SYMBOL(ep93xx_pwm_acquire_gpio);
+
+void ep93xx_pwm_release_gpio(struct platform_device *pdev)
+{
+	if (pdev->id == 1) {
+		gpio_direction_input(EP93XX_GPIO_LINE_EGPIO14);
+		gpio_free(EP93XX_GPIO_LINE_EGPIO14);
+
+		/* EGPIO[14] used for GPIO */
+		ep93xx_devcfg_clear_bits(EP93XX_SYSCON_DEVCFG_PONG);
+	}
+}
+EXPORT_SYMBOL(ep93xx_pwm_release_gpio);
+
+
+/*************************************************************************
+ * EP93xx video peripheral handling
+ *************************************************************************/
+static struct ep93xxfb_mach_info ep93xxfb_data;
+
+static struct resource ep93xx_fb_resource[] = {
+	{
+		.start		= EP93XX_RASTER_PHYS_BASE,
+		.end		= EP93XX_RASTER_PHYS_BASE + 0x800 - 1,
+		.flags		= IORESOURCE_MEM,
+	},
+};
+
+static struct platform_device ep93xx_fb_device = {
+	.name			= "ep93xx-fb",
+	.id			= -1,
+	.dev			= {
+		.platform_data	= &ep93xxfb_data,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+		.dma_mask		= &ep93xx_fb_device.dev.coherent_dma_mask,
+	},
+	.num_resources		= ARRAY_SIZE(ep93xx_fb_resource),
+	.resource		= ep93xx_fb_resource,
+};
+
+void __init ep93xx_register_fb(struct ep93xxfb_mach_info *data)
+{
+	ep93xxfb_data = *data;
+	platform_device_register(&ep93xx_fb_device);
+}
+
 extern void ep93xx_gpio_init(void);
 
 void __init ep93xx_init_devices(void)
 {
-	unsigned int v;
-
-	/*
-	 * Disallow access to MaverickCrunch initially.
-	 */
-	v = __raw_readl(EP93XX_SYSCON_DEVICE_CONFIG);
-	v &= ~EP93XX_SYSCON_DEVICE_CONFIG_CRUNCH_ENABLE;
-	__raw_writel(0xaa, EP93XX_SYSCON_SWLOCK);
-	__raw_writel(v, EP93XX_SYSCON_DEVICE_CONFIG);
+	/* Disallow access to MaverickCrunch initially */
+	ep93xx_devcfg_clear_bits(EP93XX_SYSCON_DEVCFG_CPENA);
 
 	ep93xx_gpio_init();
 
@@ -568,4 +729,5 @@ void __init ep93xx_init_devices(void)
 
 	platform_device_register(&ep93xx_rtc_device);
 	platform_device_register(&ep93xx_ohci_device);
+	platform_device_register(&ep93xx_leds);
 }
diff --git a/arch/arm/mach-ep93xx/edb93xx.c b/arch/arm/mach-ep93xx/edb93xx.c
index e9e45b9..73145ae 100644
--- a/arch/arm/mach-ep93xx/edb93xx.c
+++ b/arch/arm/mach-ep93xx/edb93xx.c
@@ -26,18 +26,16 @@
 
 #include <linux/kernel.h>
 #include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/sched.h>
-#include <linux/interrupt.h>
-#include <linux/ioport.h>
-#include <linux/mtd/physmap.h>
 #include <linux/platform_device.h>
-#include <linux/io.h>
 #include <linux/i2c.h>
+#include <linux/mtd/physmap.h>
+
 #include <mach/hardware.h>
+
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 
+
 static struct physmap_flash_data edb93xx_flash_data;
 
 static struct resource edb93xx_flash_resource = {
diff --git a/arch/arm/mach-ep93xx/gesbc9312.c b/arch/arm/mach-ep93xx/gesbc9312.c
index 3bad500..3da7ca8 100644
--- a/arch/arm/mach-ep93xx/gesbc9312.c
+++ b/arch/arm/mach-ep93xx/gesbc9312.c
@@ -12,18 +12,15 @@
 
 #include <linux/kernel.h>
 #include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/sched.h>
-#include <linux/interrupt.h>
-#include <linux/ioport.h>
-#include <linux/mtd/physmap.h>
 #include <linux/platform_device.h>
-#include <linux/io.h>
-#include <linux/i2c.h>
+#include <linux/mtd/physmap.h>
+
 #include <mach/hardware.h>
+
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 
+
 static struct physmap_flash_data gesbc9312_flash_data = {
 	.width		= 4,
 };
diff --git a/arch/arm/mach-ep93xx/gpio.c b/arch/arm/mach-ep93xx/gpio.c
index 482cf3d..1ea8871 100644
--- a/arch/arm/mach-ep93xx/gpio.c
+++ b/arch/arm/mach-ep93xx/gpio.c
@@ -17,15 +17,16 @@
 #include <linux/module.h>
 #include <linux/seq_file.h>
 #include <linux/io.h>
+#include <linux/gpio.h>
+#include <linux/irq.h>
 
-#include <mach/ep93xx-regs.h>
-#include <asm/gpio.h>
+#include <mach/hardware.h>
 
 struct ep93xx_gpio_chip {
 	struct gpio_chip	chip;
 
-	unsigned int		data_reg;
-	unsigned int		data_dir_reg;
+	void __iomem		*data_reg;
+	void __iomem		*data_dir_reg;
 };
 
 #define to_ep93xx_gpio_chip(c) container_of(c, struct ep93xx_gpio_chip, chip)
@@ -111,15 +112,61 @@ static void ep93xx_gpio_dbg_show(struct seq_file *s, struct gpio_chip *chip)
 {
 	struct ep93xx_gpio_chip *ep93xx_chip = to_ep93xx_gpio_chip(chip);
 	u8 data_reg, data_dir_reg;
-	int i;
+	int gpio, i;
 
 	data_reg = __raw_readb(ep93xx_chip->data_reg);
 	data_dir_reg = __raw_readb(ep93xx_chip->data_dir_reg);
 
-	for (i = 0; i < chip->ngpio; i++)
-		seq_printf(s, "GPIO %s%d: %s %s\n", chip->label, i,
-			   (data_reg & (1 << i)) ? "set" : "clear",
-			   (data_dir_reg & (1 << i)) ? "out" : "in");
+	gpio = ep93xx_chip->chip.base;
+	for (i = 0; i < chip->ngpio; i++, gpio++) {
+		int is_out = data_dir_reg & (1 << i);
+
+		seq_printf(s, " %s%d gpio-%-3d (%-12s) %s %s",
+				chip->label, i, gpio,
+				gpiochip_is_requested(chip, i) ? : "",
+				is_out ? "out" : "in ",
+				(data_reg & (1 << i)) ? "hi" : "lo");
+
+		if (!is_out) {
+			int irq = gpio_to_irq(gpio);
+			struct irq_desc *desc = irq_desc + irq;
+
+			if (irq >= 0 && desc->action) {
+				char *trigger;
+
+				switch (desc->status & IRQ_TYPE_SENSE_MASK) {
+				case IRQ_TYPE_NONE:
+					trigger = "(default)";
+					break;
+				case IRQ_TYPE_EDGE_FALLING:
+					trigger = "edge-falling";
+					break;
+				case IRQ_TYPE_EDGE_RISING:
+					trigger = "edge-rising";
+					break;
+				case IRQ_TYPE_EDGE_BOTH:
+					trigger = "edge-both";
+					break;
+				case IRQ_TYPE_LEVEL_HIGH:
+					trigger = "level-high";
+					break;
+				case IRQ_TYPE_LEVEL_LOW:
+					trigger = "level-low";
+					break;
+				default:
+					trigger = "?trigger?";
+					break;
+				}
+
+				seq_printf(s, " irq-%d %s%s",
+						irq, trigger,
+						(desc->status & IRQ_WAKEUP)
+							? " wakeup" : "");
+			}
+		}
+
+		seq_printf(s, "\n");
+	}
 }
 
 #define EP93XX_GPIO_BANK(name, dr, ddr, base_gpio)			\
diff --git a/arch/arm/mach-ep93xx/include/mach/ep93xx-regs.h b/arch/arm/mach-ep93xx/include/mach/ep93xx-regs.h
index 967c079..0fbf87b 100644
--- a/arch/arm/mach-ep93xx/include/mach/ep93xx-regs.h
+++ b/arch/arm/mach-ep93xx/include/mach/ep93xx-regs.h
@@ -52,40 +52,44 @@
 #define EP93XX_AHB_VIRT_BASE		0xfef00000
 #define EP93XX_AHB_SIZE			0x00100000
 
+#define EP93XX_AHB_IOMEM(x)		IOMEM(EP93XX_AHB_VIRT_BASE + (x))
+
 #define EP93XX_APB_PHYS_BASE		0x80800000
 #define EP93XX_APB_VIRT_BASE		0xfed00000
 #define EP93XX_APB_SIZE			0x00200000
 
+#define EP93XX_APB_IOMEM(x)		IOMEM(EP93XX_APB_VIRT_BASE + (x))
+
 
 /* AHB peripherals */
-#define EP93XX_DMA_BASE			((void __iomem *)		\
-					 (EP93XX_AHB_VIRT_BASE + 0x00000000))
+#define EP93XX_DMA_BASE			EP93XX_AHB_IOMEM(0x00000000)
 
-#define EP93XX_ETHERNET_BASE		(EP93XX_AHB_VIRT_BASE + 0x00010000)
 #define EP93XX_ETHERNET_PHYS_BASE	(EP93XX_AHB_PHYS_BASE + 0x00010000)
+#define EP93XX_ETHERNET_BASE		EP93XX_AHB_IOMEM(0x00010000)
 
-#define EP93XX_USB_BASE			(EP93XX_AHB_VIRT_BASE + 0x00020000)
 #define EP93XX_USB_PHYS_BASE		(EP93XX_AHB_PHYS_BASE + 0x00020000)
+#define EP93XX_USB_BASE			EP93XX_AHB_IOMEM(0x00020000)
 
-#define EP93XX_RASTER_BASE		(EP93XX_AHB_VIRT_BASE + 0x00030000)
+#define EP93XX_RASTER_PHYS_BASE		(EP93XX_AHB_PHYS_BASE + 0x00030000)
+#define EP93XX_RASTER_BASE		EP93XX_AHB_IOMEM(0x00030000)
 
-#define EP93XX_GRAPHICS_ACCEL_BASE	(EP93XX_AHB_VIRT_BASE + 0x00040000)
+#define EP93XX_GRAPHICS_ACCEL_BASE	EP93XX_AHB_IOMEM(0x00040000)
 
-#define EP93XX_SDRAM_CONTROLLER_BASE	(EP93XX_AHB_VIRT_BASE + 0x00060000)
+#define EP93XX_SDRAM_CONTROLLER_BASE	EP93XX_AHB_IOMEM(0x00060000)
 
-#define EP93XX_PCMCIA_CONTROLLER_BASE	(EP93XX_AHB_VIRT_BASE + 0x00080000)
+#define EP93XX_PCMCIA_CONTROLLER_BASE	EP93XX_AHB_IOMEM(0x00080000)
 
-#define EP93XX_BOOT_ROM_BASE		(EP93XX_AHB_VIRT_BASE + 0x00090000)
+#define EP93XX_BOOT_ROM_BASE		EP93XX_AHB_IOMEM(0x00090000)
 
-#define EP93XX_IDE_BASE			(EP93XX_AHB_VIRT_BASE + 0x000a0000)
+#define EP93XX_IDE_BASE			EP93XX_AHB_IOMEM(0x000a0000)
 
-#define EP93XX_VIC1_BASE		(EP93XX_AHB_VIRT_BASE + 0x000b0000)
+#define EP93XX_VIC1_BASE		EP93XX_AHB_IOMEM(0x000b0000)
 
-#define EP93XX_VIC2_BASE		(EP93XX_AHB_VIRT_BASE + 0x000c0000)
+#define EP93XX_VIC2_BASE		EP93XX_AHB_IOMEM(0x000c0000)
 
 
 /* APB peripherals */
-#define EP93XX_TIMER_BASE		(EP93XX_APB_VIRT_BASE + 0x00010000)
+#define EP93XX_TIMER_BASE		EP93XX_APB_IOMEM(0x00010000)
 #define EP93XX_TIMER_REG(x)		(EP93XX_TIMER_BASE + (x))
 #define EP93XX_TIMER1_LOAD		EP93XX_TIMER_REG(0x00)
 #define EP93XX_TIMER1_VALUE		EP93XX_TIMER_REG(0x04)
@@ -102,11 +106,11 @@
 #define EP93XX_TIMER3_CONTROL		EP93XX_TIMER_REG(0x88)
 #define EP93XX_TIMER3_CLEAR		EP93XX_TIMER_REG(0x8c)
 
-#define EP93XX_I2S_BASE			(EP93XX_APB_VIRT_BASE + 0x00020000)
+#define EP93XX_I2S_BASE			EP93XX_APB_IOMEM(0x00020000)
 
-#define EP93XX_SECURITY_BASE		(EP93XX_APB_VIRT_BASE + 0x00030000)
+#define EP93XX_SECURITY_BASE		EP93XX_APB_IOMEM(0x00030000)
 
-#define EP93XX_GPIO_BASE		(EP93XX_APB_VIRT_BASE + 0x00040000)
+#define EP93XX_GPIO_BASE		EP93XX_APB_IOMEM(0x00040000)
 #define EP93XX_GPIO_REG(x)		(EP93XX_GPIO_BASE + (x))
 #define EP93XX_GPIO_F_INT_TYPE1		EP93XX_GPIO_REG(0x4c)
 #define EP93XX_GPIO_F_INT_TYPE2		EP93XX_GPIO_REG(0x50)
@@ -124,32 +128,33 @@
 #define EP93XX_GPIO_B_INT_ENABLE	EP93XX_GPIO_REG(0xb8)
 #define EP93XX_GPIO_B_INT_STATUS	EP93XX_GPIO_REG(0xbc)
 
-#define EP93XX_AAC_BASE			(EP93XX_APB_VIRT_BASE + 0x00080000)
+#define EP93XX_AAC_BASE			EP93XX_APB_IOMEM(0x00080000)
 
-#define EP93XX_SPI_BASE			(EP93XX_APB_VIRT_BASE + 0x000a0000)
+#define EP93XX_SPI_BASE			EP93XX_APB_IOMEM(0x000a0000)
 
-#define EP93XX_IRDA_BASE		(EP93XX_APB_VIRT_BASE + 0x000b0000)
+#define EP93XX_IRDA_BASE		EP93XX_APB_IOMEM(0x000b0000)
 
-#define EP93XX_UART1_BASE		(EP93XX_APB_VIRT_BASE + 0x000c0000)
 #define EP93XX_UART1_PHYS_BASE		(EP93XX_APB_PHYS_BASE + 0x000c0000)
+#define EP93XX_UART1_BASE		EP93XX_APB_IOMEM(0x000c0000)
 
-#define EP93XX_UART2_BASE		(EP93XX_APB_VIRT_BASE + 0x000d0000)
 #define EP93XX_UART2_PHYS_BASE		(EP93XX_APB_PHYS_BASE + 0x000d0000)
+#define EP93XX_UART2_BASE		EP93XX_APB_IOMEM(0x000d0000)
 
-#define EP93XX_UART3_BASE		(EP93XX_APB_VIRT_BASE + 0x000e0000)
 #define EP93XX_UART3_PHYS_BASE		(EP93XX_APB_PHYS_BASE + 0x000e0000)
+#define EP93XX_UART3_BASE		EP93XX_APB_IOMEM(0x000e0000)
 
-#define EP93XX_KEY_MATRIX_BASE		(EP93XX_APB_VIRT_BASE + 0x000f0000)
+#define EP93XX_KEY_MATRIX_BASE		EP93XX_APB_IOMEM(0x000f0000)
 
-#define EP93XX_ADC_BASE			(EP93XX_APB_VIRT_BASE + 0x00100000)
-#define EP93XX_TOUCHSCREEN_BASE		(EP93XX_APB_VIRT_BASE + 0x00100000)
+#define EP93XX_ADC_BASE			EP93XX_APB_IOMEM(0x00100000)
+#define EP93XX_TOUCHSCREEN_BASE		EP93XX_APB_IOMEM(0x00100000)
 
-#define EP93XX_PWM_BASE			(EP93XX_APB_VIRT_BASE + 0x00110000)
+#define EP93XX_PWM_PHYS_BASE		(EP93XX_APB_PHYS_BASE + 0x00110000)
+#define EP93XX_PWM_BASE			EP93XX_APB_IOMEM(0x00110000)
 
-#define EP93XX_RTC_BASE			(EP93XX_APB_VIRT_BASE + 0x00120000)
 #define EP93XX_RTC_PHYS_BASE		(EP93XX_APB_PHYS_BASE + 0x00120000)
+#define EP93XX_RTC_BASE			EP93XX_APB_IOMEM(0x00120000)
 
-#define EP93XX_SYSCON_BASE		(EP93XX_APB_VIRT_BASE + 0x00130000)
+#define EP93XX_SYSCON_BASE		EP93XX_APB_IOMEM(0x00130000)
 #define EP93XX_SYSCON_REG(x)		(EP93XX_SYSCON_BASE + (x))
 #define EP93XX_SYSCON_POWER_STATE	EP93XX_SYSCON_REG(0x00)
 #define EP93XX_SYSCON_PWRCNT		EP93XX_SYSCON_REG(0x04)
@@ -172,14 +177,50 @@
 #define EP93XX_SYSCON_STANDBY		EP93XX_SYSCON_REG(0x0c)
 #define EP93XX_SYSCON_CLOCK_SET1	EP93XX_SYSCON_REG(0x20)
 #define EP93XX_SYSCON_CLOCK_SET2	EP93XX_SYSCON_REG(0x24)
-#define EP93XX_SYSCON_DEVICE_CONFIG	EP93XX_SYSCON_REG(0x80)
-#define EP93XX_SYSCON_DEVICE_CONFIG_U3EN		(1<<24)
-#define EP93XX_SYSCON_DEVICE_CONFIG_CRUNCH_ENABLE	(1<<23)
-#define EP93XX_SYSCON_DEVICE_CONFIG_U2EN		(1<<20)
-#define EP93XX_SYSCON_DEVICE_CONFIG_U1EN		(1<<18)
+#define EP93XX_SYSCON_DEVCFG		EP93XX_SYSCON_REG(0x80)
+#define EP93XX_SYSCON_DEVCFG_SWRST	(1<<31)
+#define EP93XX_SYSCON_DEVCFG_D1ONG	(1<<30)
+#define EP93XX_SYSCON_DEVCFG_D0ONG	(1<<29)
+#define EP93XX_SYSCON_DEVCFG_IONU2	(1<<28)
+#define EP93XX_SYSCON_DEVCFG_GONK	(1<<27)
+#define EP93XX_SYSCON_DEVCFG_TONG	(1<<26)
+#define EP93XX_SYSCON_DEVCFG_MONG	(1<<25)
+#define EP93XX_SYSCON_DEVCFG_U3EN	(1<<24)
+#define EP93XX_SYSCON_DEVCFG_CPENA	(1<<23)
+#define EP93XX_SYSCON_DEVCFG_A2ONG	(1<<22)
+#define EP93XX_SYSCON_DEVCFG_A1ONG	(1<<21)
+#define EP93XX_SYSCON_DEVCFG_U2EN	(1<<20)
+#define EP93XX_SYSCON_DEVCFG_EXVC	(1<<19)
+#define EP93XX_SYSCON_DEVCFG_U1EN	(1<<18)
+#define EP93XX_SYSCON_DEVCFG_TIN	(1<<17)
+#define EP93XX_SYSCON_DEVCFG_HC3IN	(1<<15)
+#define EP93XX_SYSCON_DEVCFG_HC3EN	(1<<14)
+#define EP93XX_SYSCON_DEVCFG_HC1IN	(1<<13)
+#define EP93XX_SYSCON_DEVCFG_HC1EN	(1<<12)
+#define EP93XX_SYSCON_DEVCFG_HONIDE	(1<<11)
+#define EP93XX_SYSCON_DEVCFG_GONIDE	(1<<10)
+#define EP93XX_SYSCON_DEVCFG_PONG	(1<<9)
+#define EP93XX_SYSCON_DEVCFG_EONIDE	(1<<8)
+#define EP93XX_SYSCON_DEVCFG_I2SONSSP	(1<<7)
+#define EP93XX_SYSCON_DEVCFG_I2SONAC97	(1<<6)
+#define EP93XX_SYSCON_DEVCFG_RASONP3	(1<<4)
+#define EP93XX_SYSCON_DEVCFG_RAS	(1<<3)
+#define EP93XX_SYSCON_DEVCFG_ADCPD	(1<<2)
+#define EP93XX_SYSCON_DEVCFG_KEYS	(1<<1)
+#define EP93XX_SYSCON_DEVCFG_SHENA	(1<<0)
+#define EP93XX_SYSCON_VIDCLKDIV		EP93XX_SYSCON_REG(0x84)
+#define EP93XX_SYSCON_CLKDIV_ENABLE	(1<<15)
+#define EP93XX_SYSCON_CLKDIV_ESEL	(1<<14)
+#define EP93XX_SYSCON_CLKDIV_PSEL	(1<<13)
+#define EP93XX_SYSCON_CLKDIV_PDIV_SHIFT	8
+#define EP93XX_SYSCON_KEYTCHCLKDIV	EP93XX_SYSCON_REG(0x90)
+#define EP93XX_SYSCON_KEYTCHCLKDIV_TSEN	(1<<31)
+#define EP93XX_SYSCON_KEYTCHCLKDIV_ADIV	(1<<16)
+#define EP93XX_SYSCON_KEYTCHCLKDIV_KEN	(1<<15)
+#define EP93XX_SYSCON_KEYTCHCLKDIV_KDIV	(1<<0)
 #define EP93XX_SYSCON_SWLOCK		EP93XX_SYSCON_REG(0xc0)
 
-#define EP93XX_WATCHDOG_BASE		(EP93XX_APB_VIRT_BASE + 0x00140000)
+#define EP93XX_WATCHDOG_BASE		EP93XX_APB_IOMEM(0x00140000)
 
 
 #endif
diff --git a/arch/arm/mach-ep93xx/include/mach/fb.h b/arch/arm/mach-ep93xx/include/mach/fb.h
new file mode 100644
index 0000000..d5ae11d7
--- /dev/null
+++ b/arch/arm/mach-ep93xx/include/mach/fb.h
@@ -0,0 +1,56 @@
+/*
+ * arch/arm/mach-ep93xx/include/mach/fb.h
+ */
+
+#ifndef __ASM_ARCH_EP93XXFB_H
+#define __ASM_ARCH_EP93XXFB_H
+
+struct platform_device;
+struct fb_videomode;
+struct fb_info;
+
+#define EP93XXFB_USE_MODEDB		0
+
+/* VideoAttributes flags */
+#define EP93XXFB_STATE_MACHINE_ENABLE	(1 << 0)
+#define EP93XXFB_PIXEL_CLOCK_ENABLE	(1 << 1)
+#define EP93XXFB_VSYNC_ENABLE		(1 << 2)
+#define EP93XXFB_PIXEL_DATA_ENABLE	(1 << 3)
+#define EP93XXFB_COMPOSITE_SYNC		(1 << 4)
+#define EP93XXFB_SYNC_VERT_HIGH		(1 << 5)
+#define EP93XXFB_SYNC_HORIZ_HIGH	(1 << 6)
+#define EP93XXFB_SYNC_BLANK_HIGH	(1 << 7)
+#define EP93XXFB_PCLK_FALLING		(1 << 8)
+#define EP93XXFB_ENABLE_AC		(1 << 9)
+#define EP93XXFB_ENABLE_LCD		(1 << 10)
+#define EP93XXFB_ENABLE_CCIR		(1 << 12)
+#define EP93XXFB_USE_PARALLEL_INTERFACE	(1 << 13)
+#define EP93XXFB_ENABLE_INTERRUPT	(1 << 14)
+#define EP93XXFB_USB_INTERLACE		(1 << 16)
+#define EP93XXFB_USE_EQUALIZATION	(1 << 17)
+#define EP93XXFB_USE_DOUBLE_HORZ	(1 << 18)
+#define EP93XXFB_USE_DOUBLE_VERT	(1 << 19)
+#define EP93XXFB_USE_BLANK_PIXEL	(1 << 20)
+#define EP93XXFB_USE_SDCSN0		(0 << 21)
+#define EP93XXFB_USE_SDCSN1		(1 << 21)
+#define EP93XXFB_USE_SDCSN2		(2 << 21)
+#define EP93XXFB_USE_SDCSN3		(3 << 21)
+
+#define EP93XXFB_ENABLE			(EP93XXFB_STATE_MACHINE_ENABLE	| \
+					 EP93XXFB_PIXEL_CLOCK_ENABLE	| \
+					 EP93XXFB_VSYNC_ENABLE		| \
+					 EP93XXFB_PIXEL_DATA_ENABLE)
+
+struct ep93xxfb_mach_info {
+	unsigned int			num_modes;
+	const struct fb_videomode	*modes;
+	const struct fb_videomode	*default_mode;
+	int				bpp;
+	unsigned int			flags;
+
+	int	(*setup)(struct platform_device *pdev);
+	void	(*teardown)(struct platform_device *pdev);
+	void	(*blank)(int blank_mode, struct fb_info *info);
+};
+
+#endif /* __ASM_ARCH_EP93XXFB_H */
diff --git a/arch/arm/mach-ep93xx/include/mach/hardware.h b/arch/arm/mach-ep93xx/include/mach/hardware.h
index 2866297..349fa7c 100644
--- a/arch/arm/mach-ep93xx/include/mach/hardware.h
+++ b/arch/arm/mach-ep93xx/include/mach/hardware.h
@@ -4,12 +4,23 @@
 #ifndef __ASM_ARCH_HARDWARE_H
 #define __ASM_ARCH_HARDWARE_H
 
-#include "ep93xx-regs.h"
+#include <mach/ep93xx-regs.h>
+#include <mach/platform.h>
 
 #define pcibios_assign_all_busses()	0
 
-#include "platform.h"
+/*
+ * The EP93xx has two external crystal oscillators.  To generate the
+ * required high-frequency clocks, the processor uses two phase-locked-
+ * loops (PLLs) to multiply the incoming external clock signal to much
+ * higher frequencies that are then divided down by programmable dividers
+ * to produce the needed clocks.  The PLLs operate independently of one
+ * another.
+ */
+#define EP93XX_EXT_CLK_RATE	14745600
+#define EP93XX_EXT_RTC_RATE	32768
 
-#include "ts72xx.h"
+#define EP93XX_KEYTCHCLK_DIV4	(EP93XX_EXT_CLK_RATE / 4)
+#define EP93XX_KEYTCHCLK_DIV16	(EP93XX_EXT_CLK_RATE / 16)
 
 #endif
diff --git a/arch/arm/mach-ep93xx/include/mach/io.h b/arch/arm/mach-ep93xx/include/mach/io.h
index fd5f081..cebcc1c 100644
--- a/arch/arm/mach-ep93xx/include/mach/io.h
+++ b/arch/arm/mach-ep93xx/include/mach/io.h
@@ -1,8 +1,21 @@
 /*
  * arch/arm/mach-ep93xx/include/mach/io.h
  */
+#ifndef __ASM_MACH_IO_H
+#define __ASM_MACH_IO_H
 
 #define IO_SPACE_LIMIT		0xffffffff
 
-#define __io(p)		__typesafe_io(p)
-#define __mem_pci(p)	(p)
+#define __io(p)			__typesafe_io(p)
+#define __mem_pci(p)		(p)
+
+/*
+ * A typesafe __io() variation for variable initialisers
+ */
+#ifdef __ASSEMBLER__
+#define IOMEM(p)		p
+#else
+#define IOMEM(p)		((void __iomem __force *)(p))
+#endif
+
+#endif /* __ASM_MACH_IO_H */
diff --git a/arch/arm/mach-ep93xx/include/mach/platform.h b/arch/arm/mach-ep93xx/include/mach/platform.h
index 05f0f4f..01a0f08 100644
--- a/arch/arm/mach-ep93xx/include/mach/platform.h
+++ b/arch/arm/mach-ep93xx/include/mach/platform.h
@@ -5,6 +5,8 @@
 #ifndef __ASSEMBLY__
 
 struct i2c_board_info;
+struct platform_device;
+struct ep93xxfb_mach_info;
 
 struct ep93xx_eth_data
 {
@@ -15,8 +17,28 @@ struct ep93xx_eth_data
 void ep93xx_map_io(void);
 void ep93xx_init_irq(void);
 void ep93xx_init_time(unsigned long);
+
+/* EP93xx System Controller software locked register write */
+void ep93xx_syscon_swlocked_write(unsigned int val, void __iomem *reg);
+void ep93xx_devcfg_set_clear(unsigned int set_bits, unsigned int clear_bits);
+
+static inline void ep93xx_devcfg_set_bits(unsigned int bits)
+{
+	ep93xx_devcfg_set_clear(bits, 0x00);
+}
+
+static inline void ep93xx_devcfg_clear_bits(unsigned int bits)
+{
+	ep93xx_devcfg_set_clear(0x00, bits);
+}
+
 void ep93xx_register_eth(struct ep93xx_eth_data *data, int copy_addr);
 void ep93xx_register_i2c(struct i2c_board_info *devices, int num);
+void ep93xx_register_fb(struct ep93xxfb_mach_info *data);
+void ep93xx_register_pwm(int pwm0, int pwm1);
+int ep93xx_pwm_acquire_gpio(struct platform_device *pdev);
+void ep93xx_pwm_release_gpio(struct platform_device *pdev);
+
 void ep93xx_init_devices(void);
 extern struct sys_timer ep93xx_timer;
 
diff --git a/arch/arm/mach-ep93xx/include/mach/system.h b/arch/arm/mach-ep93xx/include/mach/system.h
index ed8f35e..6d661fe 100644
--- a/arch/arm/mach-ep93xx/include/mach/system.h
+++ b/arch/arm/mach-ep93xx/include/mach/system.h
@@ -11,15 +11,13 @@ static inline void arch_idle(void)
 
 static inline void arch_reset(char mode, const char *cmd)
 {
-	u32 devicecfg;
-
 	local_irq_disable();
 
-	devicecfg = __raw_readl(EP93XX_SYSCON_DEVICE_CONFIG);
-	__raw_writel(0xaa, EP93XX_SYSCON_SWLOCK);
-	__raw_writel(devicecfg | 0x80000000, EP93XX_SYSCON_DEVICE_CONFIG);
-	__raw_writel(0xaa, EP93XX_SYSCON_SWLOCK);
-	__raw_writel(devicecfg & ~0x80000000, EP93XX_SYSCON_DEVICE_CONFIG);
+	/*
+	 * Set then clear the SWRST bit to initiate a software reset
+	 */
+	ep93xx_devcfg_set_bits(EP93XX_SYSCON_DEVCFG_SWRST);
+	ep93xx_devcfg_clear_bits(EP93XX_SYSCON_DEVCFG_SWRST);
 
 	while (1)
 		;
diff --git a/arch/arm/mach-ep93xx/include/mach/ts72xx.h b/arch/arm/mach-ep93xx/include/mach/ts72xx.h
index 4117344..3bd934e 100644
--- a/arch/arm/mach-ep93xx/include/mach/ts72xx.h
+++ b/arch/arm/mach-ep93xx/include/mach/ts72xx.h
@@ -67,7 +67,6 @@
 
 
 #ifndef __ASSEMBLY__
-#include <linux/io.h>
 
 static inline int board_is_ts7200(void)
 {
diff --git a/arch/arm/mach-ep93xx/micro9.c b/arch/arm/mach-ep93xx/micro9.c
index 15d6815..0a313e8 100644
--- a/arch/arm/mach-ep93xx/micro9.c
+++ b/arch/arm/mach-ep93xx/micro9.c
@@ -9,21 +9,16 @@
  * published by the Free Software Foundation.
  */
 
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/ioport.h>
 #include <linux/kernel.h>
-#include <linux/mm.h>
+#include <linux/init.h>
 #include <linux/platform_device.h>
-#include <linux/sched.h>
-#include <linux/io.h>
-#include <linux/i2c.h>
 #include <linux/mtd/physmap.h>
 
 #include <mach/hardware.h>
 
-#include <asm/mach/arch.h>
 #include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+
 
 static struct ep93xx_eth_data micro9_eth_data = {
 	.phy_id		= 0x1f,
diff --git a/arch/arm/mach-ep93xx/ts72xx.c b/arch/arm/mach-ep93xx/ts72xx.c
index aaf1371..259f782 100644
--- a/arch/arm/mach-ep93xx/ts72xx.c
+++ b/arch/arm/mach-ep93xx/ts72xx.c
@@ -12,19 +12,18 @@
 
 #include <linux/kernel.h>
 #include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/sched.h>
-#include <linux/interrupt.h>
-#include <linux/ioport.h>
-#include <linux/mtd/physmap.h>
 #include <linux/platform_device.h>
-#include <linux/m48t86.h>
 #include <linux/io.h>
-#include <linux/i2c.h>
+#include <linux/m48t86.h>
+#include <linux/mtd/physmap.h>
+
 #include <mach/hardware.h>
+#include <mach/ts72xx.h>
+
 #include <asm/mach-types.h>
-#include <asm/mach/arch.h>
 #include <asm/mach/map.h>
+#include <asm/mach/arch.h>
+
 
 static struct map_desc ts72xx_io_desc[] __initdata = {
 	{