diff options
Diffstat (limited to 'arch/arm/mach-at91/board-sam9g20ek.c')
| -rw-r--r-- | arch/arm/mach-at91/board-sam9g20ek.c | 13 |
1 files changed, 10 insertions, 3 deletions
diff --git a/arch/arm/mach-at91/board-sam9g20ek.c b/arch/arm/mach-at91/board-sam9g20ek.c index 64fc75c..843d628 100644 --- a/arch/arm/mach-at91/board-sam9g20ek.c +++ b/arch/arm/mach-at91/board-sam9g20ek.c @@ -86,6 +86,8 @@ static void __init ek_init_early(void) */ static struct at91_usbh_data __initdata ek_usbh_data = { .ports = 2, + .vbus_pin = {-EINVAL, -EINVAL}, + .overcurrent_pin= {-EINVAL, -EINVAL}, }; /* @@ -93,7 +95,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = { */ static struct at91_udc_data __initdata ek_udc_data = { .vbus_pin = AT91_PIN_PC5, - .pullup_pin = 0, /* pull-up driven by UDC */ + .pullup_pin = -EINVAL, /* pull-up driven by UDC */ }; @@ -123,7 +125,7 @@ static struct spi_board_info ek_spi_devices[] = { /* * MACB Ethernet device */ -static struct at91_eth_data __initdata ek_macb_data = { +static struct macb_platform_data __initdata ek_macb_data = { .phy_irq_pin = AT91_PIN_PA7, .is_rmii = 1, }; @@ -163,6 +165,7 @@ static struct atmel_nand_data __initdata ek_nand_data = { .cle = 22, .rdy_pin = AT91_PIN_PC13, .enable_pin = AT91_PIN_PC14, + .det_pin = -EINVAL, .parts = ek_nand_partition, .num_parts = ARRAY_SIZE(ek_nand_partition), }; @@ -195,7 +198,7 @@ static void __init ek_add_device_nand(void) ek_nand_smc_config.mode |= AT91_SMC_DBW_8; /* configure chip-select 3 (NAND) */ - sam9_smc_configure(3, &ek_nand_smc_config); + sam9_smc_configure(0, 3, &ek_nand_smc_config); at91_add_device_nand(&ek_nand_data); } @@ -210,6 +213,7 @@ static struct mci_platform_data __initdata ek_mmc_data = { .slot[1] = { .bus_width = 4, .detect_pin = AT91_PIN_PC9, + .wp_pin = -EINVAL, }, }; @@ -218,6 +222,8 @@ static struct at91_mmc_data __initdata ek_mmc_data = { .slot_b = 1, /* Only one slot so use slot B */ .wire4 = 1, .det_pin = AT91_PIN_PC9, + .wp_pin = -EINVAL, + .vcc_pin = -EINVAL, }; #endif @@ -227,6 +233,7 @@ static void __init ek_add_device_mmc(void) if (ek_have_2mmc()) { ek_mmc_data.slot[0].bus_width = 4; ek_mmc_data.slot[0].detect_pin = AT91_PIN_PC2; + ek_mmc_data.slot[0].wp_pin = -1; } at91_add_device_mci(0, &ek_mmc_data); #else |
