diff options
Diffstat (limited to 'Documentation')
9 files changed, 141 insertions, 32 deletions
diff --git a/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt index 532b1d4..6cd3525 100644 --- a/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt @@ -46,13 +46,14 @@ Required Properties: - if CIU clock divider value is 0 (that is divide by 1), both tx and rx phase shift clocks should be 0. -Required properties for a slot: +Required properties for a slot (Deprecated - Recommend to use one slot per host): * gpios: specifies a list of gpios used for command, clock and data bus. The first gpio is the command line and the second gpio is the clock line. The rest of the gpios (depending on the bus-width property) are the data lines in no particular order. The format of the gpio specifier depends on the gpio controller. +(Deprecated - Refer to Documentation/devicetree/binding/pinctrl/samsung-pinctrl.txt) Example: @@ -69,21 +70,13 @@ Example: dwmmc0@12200000 { num-slots = <1>; - supports-highspeed; + cap-mmc-highspeed; + cap-sd-highspeed; broken-cd; fifo-depth = <0x80>; card-detect-delay = <200>; samsung,dw-mshc-ciu-div = <3>; samsung,dw-mshc-sdr-timing = <2 3>; samsung,dw-mshc-ddr-timing = <1 2>; - - slot@0 { - reg = <0>; - bus-width = <8>; - gpios = <&gpc0 0 2 0 3>, <&gpc0 1 2 0 3>, - <&gpc1 0 2 3 3>, <&gpc1 1 2 3 3>, - <&gpc1 2 2 3 3>, <&gpc1 3 2 3 3>, - <&gpc0 3 2 3 3>, <&gpc0 4 2 3 3>, - <&gpc0 5 2 3 3>, <&gpc0 6 2 3 3>; - }; + bus-width = <8>; }; diff --git a/Documentation/devicetree/bindings/mmc/k3-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/k3-dw-mshc.txt index e5bc49f..3b35449 100644 --- a/Documentation/devicetree/bindings/mmc/k3-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/k3-dw-mshc.txt @@ -34,13 +34,11 @@ Example: num-slots = <1>; vmmc-supply = <&ldo12>; fifo-depth = <0x100>; - supports-highspeed; pinctrl-names = "default"; pinctrl-0 = <&sd_pmx_pins &sd_cfg_func1 &sd_cfg_func2>; - slot@0 { - reg = <0>; - bus-width = <4>; - disable-wp; - cd-gpios = <&gpio10 3 0>; - }; + bus-width = <4>; + disable-wp; + cd-gpios = <&gpio10 3 0>; + cap-mmc-highspeed; + cap-sd-highspeed; }; diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt index 3c18001..431716e 100644 --- a/Documentation/devicetree/bindings/mmc/mmc.txt +++ b/Documentation/devicetree/bindings/mmc/mmc.txt @@ -34,8 +34,8 @@ Optional properties: - cap-power-off-card: powering off the card is safe - cap-sdio-irq: enable SDIO IRQ signalling on this interface - full-pwr-cycle: full power cycle of the card is supported -- mmc-highspeed-ddr-1_8v: eMMC high-speed DDR mode(1.8V I/O) is supported -- mmc-highspeed-ddr-1_2v: eMMC high-speed DDR mode(1.2V I/O) is supported +- mmc-ddr-1_8v: eMMC high-speed DDR mode(1.8V I/O) is supported +- mmc-ddr-1_2v: eMMC high-speed DDR mode(1.2V I/O) is supported - mmc-hs200-1_8v: eMMC HS200 mode(1.8V I/O) is supported - mmc-hs200-1_2v: eMMC HS200 mode(1.2V I/O) is supported - mmc-hs400-1_8v: eMMC HS400 mode(1.8V I/O) is supported diff --git a/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt b/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt new file mode 100644 index 0000000..299081f --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt @@ -0,0 +1,32 @@ +* Renesas Multi Media Card Interface (MMCIF) Controller + +This file documents differences between the core properties in mmc.txt +and the properties used by the MMCIF device. + + +Required properties: + +- compatible: must contain one of the following + - "renesas,mmcif-r8a7740" for the MMCIF found in r8a7740 SoCs + - "renesas,mmcif-r8a7790" for the MMCIF found in r8a7790 SoCs + - "renesas,mmcif-r8a7791" for the MMCIF found in r8a7791 SoCs + - "renesas,sh-mmcif" for the generic MMCIF + +- clocks: reference to the functional clock + +- dmas: reference to the DMA channels, one per channel name listed in the + dma-names property. +- dma-names: must contain "tx" for the transmit DMA channel and "rx" for the + receive DMA channel. + + +Example: R8A7790 (R-Car H2) MMCIF0 + + mmcif0: mmc@ee200000 { + compatible = "renesas,mmcif-r8a7790", "renesas,sh-mmcif"; + reg = <0 0xee200000 0 0x80>; + interrupts = <0 169 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp3_clks R8A7790_CLK_MMCIF0>; + dmas = <&dmac0 0xd1>, <&dmac0 0xd2>; + dma-names = "tx", "rx"; + }; diff --git a/Documentation/devicetree/bindings/mmc/sdhci-msm.txt b/Documentation/devicetree/bindings/mmc/sdhci-msm.txt index 81b33b5..485483a 100644 --- a/Documentation/devicetree/bindings/mmc/sdhci-msm.txt +++ b/Documentation/devicetree/bindings/mmc/sdhci-msm.txt @@ -27,8 +27,8 @@ Example: bus-width = <8>; non-removable; - vmmc = <&pm8941_l20>; - vqmmc = <&pm8941_s3>; + vmmc-supply = <&pm8941_l20>; + vqmmc-supply = <&pm8941_s3>; pinctrl-names = "default"; pinctrl-0 = <&sdc1_clk &sdc1_cmd &sdc1_data>; @@ -44,8 +44,8 @@ Example: bus-width = <4>; cd-gpios = <&msmgpio 62 0x1>; - vmmc = <&pm8941_l21>; - vqmmc = <&pm8941_l13>; + vmmc-supply = <&pm8941_l21>; + vqmmc-supply = <&pm8941_l13>; pinctrl-names = "default"; pinctrl-0 = <&sdc2_clk &sdc2_cmd &sdc2_data>; diff --git a/Documentation/devicetree/bindings/mmc/sdhci-st.txt b/Documentation/devicetree/bindings/mmc/sdhci-st.txt new file mode 100644 index 0000000..7527db4 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/sdhci-st.txt @@ -0,0 +1,33 @@ +* STMicroelectronics sdhci-st MMC/SD controller + +This file documents the differences between the core properties in +Documentation/devicetree/bindings/mmc/mmc.txt and the properties +used by the sdhci-st driver. + +Required properties: +- compatible : Must be "st,sdhci" +- clock-names : Should be "mmc" + See: Documentation/devicetree/bindings/resource-names.txt +- clocks : Phandle of the clock used by the sdhci controler + See: Documentation/devicetree/bindings/clock/clock-bindings.txt + +Optional properties: +- non-removable: non-removable slot + See: Documentation/devicetree/bindings/mmc/mmc.txt +- bus-width: Number of data lines + See: Documentation/devicetree/bindings/mmc/mmc.txt + +Example: + +mmc0: sdhci@fe81e000 { + compatible = "st,sdhci"; + status = "disabled"; + reg = <0xfe81e000 0x1000>; + interrupts = <GIC_SPI 127 IRQ_TYPE_NONE>; + interrupt-names = "mmcirq"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_mmc0>; + clock-names = "mmc"; + clocks = <&clk_s_a1_ls 1>; + bus-width = <8> +}; diff --git a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt index 2d4a725..346c609 100644 --- a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt @@ -67,7 +67,8 @@ Optional properties: * card-detect-delay: Delay in milli-seconds before detecting card after card insert event. The default value is 0. -* supports-highspeed: Enables support for high speed cards (up to 50MHz) +* supports-highspeed (DEPRECATED): Enables support for high speed cards (up to 50MHz) + (use "cap-mmc-highspeed" or "cap-sd-highspeed" instead) * broken-cd: as documented in mmc core bindings. @@ -98,14 +99,11 @@ board specific portions as listed below. clock-frequency = <400000000>; clock-freq-min-max = <400000 200000000>; num-slots = <1>; - supports-highspeed; broken-cd; fifo-depth = <0x80>; card-detect-delay = <200>; vmmc-supply = <&buck8>; - - slot@0 { - reg = <0>; - bus-width = <8>; - }; + bus-width = <8>; + cap-mmc-highspeed; + cap-sd-highspeed; }; diff --git a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt index ce80561..76bf087 100644 --- a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt +++ b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt @@ -12,6 +12,7 @@ Required properties: Should be "ti,omap3-hsmmc", for OMAP3 controllers Should be "ti,omap3-pre-es3-hsmmc" for OMAP3 controllers pre ES3.0 Should be "ti,omap4-hsmmc", for OMAP4 controllers + Should be "ti,am33xx-hsmmc", for AM335x controllers - ti,hwmods: Must be "mmc<n>", n is controller instance starting 1 Optional properties: @@ -56,3 +57,56 @@ Examples: &edma 25>; dma-names = "tx", "rx"; }; + +[workaround for missing swakeup on am33xx] + +This SOC is missing the swakeup line, it will not detect SDIO irq +while in suspend. + + ------ + | PRCM | + ------ + ^ | + swakeup | | fclk + | v + ------ ------- ----- + | card | -- CIRQ --> | hsmmc | -- IRQ --> | CPU | + ------ ------- ----- + +In suspend the fclk is off and the module is disfunctional. Even register reads +will fail. A small logic in the host will request fclk restore, when an +external event is detected. Once the clock is restored, the host detects the +event normally. Since am33xx doesn't have this line it never wakes from +suspend. + +The workaround is to reconfigure the dat1 line as a GPIO upon suspend. To make +this work, we need to set the named pinctrl states "default" and "idle". +Prepare idle to remux dat1 as a gpio, and default to remux it back as sdio +dat1. The MMC driver will then toggle between idle and default state during +runtime. + +In summary: +1. select matching 'compatible' section, see example below. +2. specify pinctrl states "default" and "idle", "sleep" is optional. +3. specify the gpio irq used for detecting sdio irq in suspend + +If configuration is incomplete, a warning message is emitted "falling back to +polling". Also check the "sdio irq mode" in /sys/kernel/debug/mmc0/regs. Mind +not every application needs SDIO irq, e.g. MMC cards. + + mmc1: mmc@48060100 { + compatible = "ti,am33xx-hsmmc"; + ... + pinctrl-names = "default", "idle", "sleep" + pinctrl-0 = <&mmc1_pins>; + pinctrl-1 = <&mmc1_idle>; + pinctrl-2 = <&mmc1_sleep>; + ... + interrupts-extended = <&intc 64 &gpio2 28 0>; + }; + + mmc1_idle : pinmux_cirq_pin { + pinctrl-single,pins = < + 0x0f8 0x3f /* GPIO2_28 */ + >; + }; diff --git a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt index 6a2a116..fa0f327 100644 --- a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt +++ b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt @@ -18,6 +18,7 @@ Required properties: "renesas,sdhi-r8a7778" - SDHI IP on R8A7778 SoC "renesas,sdhi-r8a7779" - SDHI IP on R8A7779 SoC "renesas,sdhi-r8a7790" - SDHI IP on R8A7790 SoC + "renesas,sdhi-r8a7791" - SDHI IP on R8A7791 SoC Optional properties: - toshiba,mmc-wrprotect-disable: write-protect detection is unavailable |
