diff options
Diffstat (limited to 'Documentation')
-rw-r--r-- | Documentation/devicetree/bindings/i2c/i2c-designware.txt | 4 | ||||
-rw-r--r-- | Documentation/devicetree/bindings/i2c/i2c-img-scb.txt | 26 | ||||
-rw-r--r-- | Documentation/devicetree/bindings/i2c/i2c-imx.txt | 11 | ||||
-rw-r--r-- | Documentation/devicetree/bindings/i2c/i2c-meson.txt | 24 | ||||
-rw-r--r-- | Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt | 14 | ||||
-rw-r--r-- | Documentation/devicetree/bindings/i2c/trivial-devices.txt | 8 | ||||
-rw-r--r-- | Documentation/i2c/busses/i2c-i801 | 1 | ||||
-rw-r--r-- | Documentation/i2c/upgrading-clients | 6 | ||||
-rw-r--r-- | Documentation/i2c/writing-clients | 8 |
9 files changed, 92 insertions, 10 deletions
diff --git a/Documentation/devicetree/bindings/i2c/i2c-designware.txt b/Documentation/devicetree/bindings/i2c/i2c-designware.txt index 5199b0c..fee26dc 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-designware.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-designware.txt @@ -14,10 +14,10 @@ Optional properties : - i2c-sda-hold-time-ns : should contain the SDA hold time in nanoseconds. This option is only supported in hardware blocks version 1.11a or newer. - - i2c-scl-falling-time : should contain the SCL falling time in nanoseconds. + - i2c-scl-falling-time-ns : should contain the SCL falling time in nanoseconds. This value which is by default 300ns is used to compute the tLOW period. - - i2c-sda-falling-time : should contain the SDA falling time in nanoseconds. + - i2c-sda-falling-time-ns : should contain the SDA falling time in nanoseconds. This value which is by default 300ns is used to compute the tHIGH period. Example : diff --git a/Documentation/devicetree/bindings/i2c/i2c-img-scb.txt b/Documentation/devicetree/bindings/i2c/i2c-img-scb.txt new file mode 100644 index 0000000..b646160 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-img-scb.txt @@ -0,0 +1,26 @@ +IMG Serial Control Bus (SCB) I2C Controller + +Required Properties: +- compatible: "img,scb-i2c" +- reg: Physical base address and length of controller registers +- interrupts: Interrupt number used by the controller +- clocks : Should contain a clock specifier for each entry in clock-names +- clock-names : Should contain the following entries: + "scb", for the SCB core clock. + "sys", for the system clock. +- clock-frequency: The I2C bus frequency in Hz +- #address-cells: Should be <1> +- #size-cells: Should be <0> + +Example: + +i2c@18100000 { + compatible = "img,scb-i2c"; + reg = <0x18100000 0x200>; + interrupts = <GIC_SHARED 2 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&i2c0_clk>, <&system_clk>; + clock-names = "scb", "sys"; + clock-frequency = <400000>; + #address-cells = <1>; + #size-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-imx.txt b/Documentation/devicetree/bindings/i2c/i2c-imx.txt index 4a8513e..52d37fd 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-imx.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-imx.txt @@ -11,6 +11,8 @@ Required properties: Optional properties: - clock-frequency : Constains desired I2C/HS-I2C bus clock frequency in Hz. The absence of the propoerty indicates the default frequency 100 kHz. +- dmas: A list of two dma specifiers, one for each entry in dma-names. +- dma-names: should contain "tx" and "rx". Examples: @@ -26,3 +28,12 @@ i2c@70038000 { /* HS-I2C on i.MX51 */ interrupts = <64>; clock-frequency = <400000>; }; + +i2c0: i2c@40066000 { /* i2c0 on vf610 */ + compatible = "fsl,vf610-i2c"; + reg = <0x40066000 0x1000>; + interrupts =<0 71 0x04>; + dmas = <&edma0 0 50>, + <&edma0 0 51>; + dma-names = "rx","tx"; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-meson.txt b/Documentation/devicetree/bindings/i2c/i2c-meson.txt new file mode 100644 index 0000000..682f9a6 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-meson.txt @@ -0,0 +1,24 @@ +Amlogic Meson I2C controller + +Required properties: + - compatible: must be "amlogic,meson6-i2c" + - reg: physical address and length of the device registers + - interrupts: a single interrupt specifier + - clocks: clock for the device + - #address-cells: should be <1> + - #size-cells: should be <0> + +Optional properties: +- clock-frequency: the desired I2C bus clock frequency in Hz; in + absence of this property the default value is used (100 kHz). + +Examples: + + i2c@c8100500 { + compatible = "amlogic,meson6-i2c"; + reg = <0xc8100500 0x20>; + interrupts = <0 92 1>; + clocks = <&clk81>; + #address-cells = <1>; + #size-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt b/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt index d2153ce..2bfc6e7 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt @@ -2,6 +2,15 @@ Device tree configuration for Renesas IIC (sh_mobile) driver Required properties: - compatible : "renesas,iic-<soctype>". "renesas,rmobile-iic" as fallback + Examples with soctypes are: + - "renesas,iic-r8a73a4" (R-Mobile APE6) + - "renesas,iic-r8a7740" (R-Mobile A1) + - "renesas,iic-r8a7790" (R-Car H2) + - "renesas,iic-r8a7791" (R-Car M2-W) + - "renesas,iic-r8a7792" (R-Car V2H) + - "renesas,iic-r8a7793" (R-Car M2-N) + - "renesas,iic-r8a7794" (R-Car E2) + - "renesas,iic-sh73a0" (SH-Mobile AG5) - reg : address start and address range size of device - interrupts : interrupt of device - clocks : clock for device @@ -10,6 +19,11 @@ Required properties: Optional properties: - clock-frequency : frequency of bus clock in Hz. Default 100kHz if unset. +- dmas : Must contain a list of two references to DMA + specifiers, one for transmission, and one for + reception. +- dma-names : Must contain a list of two DMA names, "tx" and "rx". + Pinctrl properties might be needed, too. See there. diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt index 605dcca..9f4e382 100644 --- a/Documentation/devicetree/bindings/i2c/trivial-devices.txt +++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt @@ -17,6 +17,9 @@ adi,adt7473 +/-1C TDM Extended Temp Range I.C adi,adt7475 +/-1C TDM Extended Temp Range I.C adi,adt7476 +/-1C TDM Extended Temp Range I.C adi,adt7490 +/-1C TDM Extended Temp Range I.C +adi,adxl345 Three-Axis Digital Accelerometer +adi,adxl346 Three-Axis Digital Accelerometer +adi,adxl34x Three-Axis Digital Accelerometer at,24c08 i2c serial eeprom (24cxx) atmel,24c00 i2c serial eeprom (24cxx) atmel,24c01 i2c serial eeprom (24cxx) @@ -76,7 +79,12 @@ ovti,ov5642 OV5642: Color CMOS QSXGA (5-megapixel) Image Sensor with OmniBSI an pericom,pt7c4338 Real-time Clock Module plx,pex8648 48-Lane, 12-Port PCI Express Gen 2 (5.0 GT/s) Switch ramtron,24c64 i2c serial eeprom (24cxx) +ricoh,r2025sd I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC +ricoh,r2221tl I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC ricoh,rs5c372a I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC +ricoh,rs5c372b I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC +ricoh,rv5c386 I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC +ricoh,rv5c387a I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC samsung,24ad0xd1 S524AD0XF1 (128K/256K-bit Serial EEPROM for Low Power) sii,s35390a 2-wire CMOS real-time clock st-micro,24c256 i2c serial eeprom (24cxx) diff --git a/Documentation/i2c/busses/i2c-i801 b/Documentation/i2c/busses/i2c-i801 index 793c83d..82f48f7 100644 --- a/Documentation/i2c/busses/i2c-i801 +++ b/Documentation/i2c/busses/i2c-i801 @@ -29,6 +29,7 @@ Supported adapters: * Intel Wildcat Point-LP (PCH) * Intel BayTrail (SOC) * Intel Sunrise Point-H (PCH) + * Intel Sunrise Point-LP (PCH) Datasheets: Publicly available at the Intel website On Intel Patsburg and later chipsets, both the normal host SMBus controller diff --git a/Documentation/i2c/upgrading-clients b/Documentation/i2c/upgrading-clients index 8e5fbd8..ccba3ff 100644 --- a/Documentation/i2c/upgrading-clients +++ b/Documentation/i2c/upgrading-clients @@ -79,11 +79,10 @@ static struct i2c_driver example_driver = { .driver = { .owner = THIS_MODULE, .name = "example", + .pm = &example_pm_ops, }, .attach_adapter = example_attach_adapter, .detach_client = example_detach, - .suspend = example_suspend, - .resume = example_resume, }; @@ -272,10 +271,9 @@ static struct i2c_driver example_driver = { .driver = { .owner = THIS_MODULE, .name = "example", + .pm = &example_pm_ops, }, .id_table = example_idtable, .probe = example_probe, .remove = example_remove, - .suspend = example_suspend, - .resume = example_resume, }; diff --git a/Documentation/i2c/writing-clients b/Documentation/i2c/writing-clients index 6b344b5..a755b14 100644 --- a/Documentation/i2c/writing-clients +++ b/Documentation/i2c/writing-clients @@ -36,6 +36,7 @@ MODULE_DEVICE_TABLE(i2c, foo_idtable); static struct i2c_driver foo_driver = { .driver = { .name = "foo", + .pm = &foo_pm_ops, /* optional */ }, .id_table = foo_idtable, @@ -47,8 +48,6 @@ static struct i2c_driver foo_driver = { .address_list = normal_i2c, .shutdown = foo_shutdown, /* optional */ - .suspend = foo_suspend, /* optional */ - .resume = foo_resume, /* optional */ .command = foo_command, /* optional, deprecated */ } @@ -279,8 +278,9 @@ Power Management If your I2C device needs special handling when entering a system low power state -- like putting a transceiver into a low power mode, or -activating a system wakeup mechanism -- do that in the suspend() method. -The resume() method should reverse what the suspend() method does. +activating a system wakeup mechanism -- do that by implementing the +appropriate callbacks for the dev_pm_ops of the driver (like suspend +and resume). These are standard driver model calls, and they work just like they would for any other driver stack. The calls can sleep, and can use |