diff options
Diffstat (limited to 'Documentation')
-rw-r--r-- | Documentation/devicetree/bindings/powerpc/fsl/raideng.txt | 81 | ||||
-rw-r--r-- | Documentation/powerpc/ptrace.txt | 16 |
2 files changed, 97 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/powerpc/fsl/raideng.txt b/Documentation/devicetree/bindings/powerpc/fsl/raideng.txt new file mode 100644 index 0000000..4ad29b9 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/raideng.txt @@ -0,0 +1,81 @@ +* Freescale 85xx RAID Engine nodes + +RAID Engine nodes are defined to describe on-chip RAID accelerators. Each RAID +Engine should have a separate node. + +Supported chips: +P5020, P5040 + +Required properties: + +- compatible: Should contain "fsl,raideng-v1.0" as the value + This identifies RAID Engine block. 1 in 1.0 represents + major number whereas 0 represents minor number. The + version matches the hardware IP version. +- reg: offset and length of the register set for the device +- ranges: standard ranges property specifying the translation + between child address space and parent address space + +Example: + /* P5020 */ + raideng: raideng@320000 { + compatible = "fsl,raideng-v1.0"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x320000 0x10000>; + ranges = <0 0x320000 0x10000>; + }; + + +There must be a sub-node for each job queue present in RAID Engine +This node must be a sub-node of the main RAID Engine node + +- compatible: Should contain "fsl,raideng-v1.0-job-queue" as the value + This identifies the job queue interface +- reg: offset and length of the register set for job queue +- ranges: standard ranges property specifying the translation + between child address space and parent address space + +Example: + /* P5020 */ + raideng_jq0@1000 { + compatible = "fsl,raideng-v1.0-job-queue"; + reg = <0x1000 0x1000>; + ranges = <0x0 0x1000 0x1000>; + }; + + +There must be a sub-node for each job ring present in RAID Engine +This node must be a sub-node of job queue node + +- compatible: Must contain "fsl,raideng-v1.0-job-ring" as the value + This identifies job ring. Should contain either + "fsl,raideng-v1.0-hp-ring" or "fsl,raideng-v1.0-lp-ring" + depending upon whether ring has high or low priority +- reg: offset and length of the register set for job ring +- interrupts: interrupt mapping for job ring IRQ + +Optional property: + +- fsl,liodn: Specifies the LIODN to be used for Job Ring. This + property is normally set by firmware. Value + is of 12-bits which is the LIODN number for this JR. + This property is used by the IOMMU (PAMU) to distinquish + transactions from this JR and than be able to do address + translation & protection accordingly. + +Example: + /* P5020 */ + raideng_jq0@1000 { + compatible = "fsl,raideng-v1.0-job-queue"; + reg = <0x1000 0x1000>; + ranges = <0x0 0x1000 0x1000>; + + raideng_jr0: jr@0 { + compatible = "fsl,raideng-v1.0-job-ring", "fsl,raideng-v1.0-hp-ring"; + reg = <0x0 0x400>; + interrupts = <139 2 0 0>; + interrupt-parent = <&mpic>; + fsl,liodn = <0x41>; + }; + }; diff --git a/Documentation/powerpc/ptrace.txt b/Documentation/powerpc/ptrace.txt index f4a5499..f2a7a39 100644 --- a/Documentation/powerpc/ptrace.txt +++ b/Documentation/powerpc/ptrace.txt @@ -127,6 +127,22 @@ Some examples of using the structure to: p.addr2 = (uint64_t) end_range; p.condition_value = 0; +- set a watchpoint in server processors (BookS) + + p.version = 1; + p.trigger_type = PPC_BREAKPOINT_TRIGGER_RW; + p.addr_mode = PPC_BREAKPOINT_MODE_RANGE_INCLUSIVE; + or + p.addr_mode = PPC_BREAKPOINT_MODE_EXACT; + + p.condition_mode = PPC_BREAKPOINT_CONDITION_NONE; + p.addr = (uint64_t) begin_range; + /* For PPC_BREAKPOINT_MODE_RANGE_INCLUSIVE addr2 needs to be specified, where + * addr2 - addr <= 8 Bytes. + */ + p.addr2 = (uint64_t) end_range; + p.condition_value = 0; + 3. PTRACE_DELHWDEBUG Takes an integer which identifies an existing breakpoint or watchpoint |