6 files changed, 25 insertions, 20 deletions
diff --git a/Documentation/ABI/testing/sysfs-bus-usb b/Documentation/ABI/testing/sysfs-bus-usb
index 9759b8c..9c8926c 100644
--- a/Documentation/ABI/testing/sysfs-bus-usb
+++ b/Documentation/ABI/testing/sysfs-bus-usb
@@ -60,7 +60,7 @@ Users:
 		PowerTOP <power@bughost.org>
 		http://www.lesswatts.org/projects/powertop/
 
-What:		/sys/bus/usb/device/<busnum>-<devnum>...:<config num>-<interface num>/supports_autosuspend
+What:		/sys/bus/usb/devices/<busnum>-<port[.port]>...:<config num>-<interface num>/supports_autosuspend
 Date:		January 2008
 KernelVersion:	2.6.27
 Contact:	Sarah Sharp <sarah.a.sharp@intel.com>
diff --git a/Documentation/DocBook/device-drivers.tmpl b/Documentation/DocBook/device-drivers.tmpl
index cbfdf54..fe397f9 100644
--- a/Documentation/DocBook/device-drivers.tmpl
+++ b/Documentation/DocBook/device-drivers.tmpl
@@ -84,7 +84,7 @@ X!Iinclude/linux/kobject.h
 
      <sect1><title>Kernel utility functions</title>
 !Iinclude/linux/kernel.h
-!Ekernel/printk.c
+!Ekernel/printk/printk.c
 !Ekernel/panic.c
 !Ekernel/sys.c
 !Ekernel/rcupdate.c
diff --git a/Documentation/devicetree/bindings/usb/usb3503.txt b/Documentation/devicetree/bindings/usb/usb3503.txt
index 8c5be48..a018da4 100644
--- a/Documentation/devicetree/bindings/usb/usb3503.txt
+++ b/Documentation/devicetree/bindings/usb/usb3503.txt
@@ -1,8 +1,11 @@
 SMSC USB3503 High-Speed Hub Controller
 
 Required properties:
-- compatible: Should be "smsc,usb3503".
-- reg: Specifies the i2c slave address, it should be 0x08.
+- compatible: Should be "smsc,usb3503" or "smsc,usb3503a".
+
+Optional properties:
+- reg: Specifies the i2c slave address, it is required and should be 0x08
+       if I2C is used.
 - connect-gpios: Should specify GPIO for connect.
 - disabled-ports: Should specify the ports unused.
 	'1' or '2' or '3' are availe for this property to describe the port
diff --git a/Documentation/sysctl/net.txt b/Documentation/sysctl/net.txt
index 1c15043..d569f2a 100644
--- a/Documentation/sysctl/net.txt
+++ b/Documentation/sysctl/net.txt
@@ -52,7 +52,7 @@ Default: 64
 
 busy_read
 ----------------
-Low latency busy poll timeout for socket reads. (needs CONFIG_NET_LL_RX_POLL)
+Low latency busy poll timeout for socket reads. (needs CONFIG_NET_RX_BUSY_POLL)
 Approximate time in us to busy loop waiting for packets on the device queue.
 This sets the default value of the SO_BUSY_POLL socket option.
 Can be set or overridden per socket by setting socket option SO_BUSY_POLL,
@@ -63,7 +63,7 @@ Default: 0 (off)
 
 busy_poll
 ----------------
-Low latency busy poll timeout for poll and select. (needs CONFIG_NET_LL_RX_POLL)
+Low latency busy poll timeout for poll and select. (needs CONFIG_NET_RX_BUSY_POLL)
 Approximate time in us to busy loop waiting for events.
 Recommended value depends on the number of sockets you poll on.
 For several sockets 50, for several hundreds 100.
diff --git a/Documentation/usb/URB.txt b/Documentation/usb/URB.txt
index 00d2c64..50da0d4 100644
--- a/Documentation/usb/URB.txt
+++ b/Documentation/usb/URB.txt
@@ -195,13 +195,12 @@ by the completion handler.
 
 The handler is of the following type:
 
-	typedef void (*usb_complete_t)(struct urb *, struct pt_regs *)
+	typedef void (*usb_complete_t)(struct urb *)
 
-I.e., it gets the URB that caused the completion call, plus the
-register values at the time of the corresponding interrupt (if any).
-In the completion handler, you should have a look at urb->status to
-detect any USB errors. Since the context parameter is included in the URB,
-you can pass information to the completion handler. 
+I.e., it gets the URB that caused the completion call. In the completion
+handler, you should have a look at urb->status to detect any USB errors.
+Since the context parameter is included in the URB, you can pass
+information to the completion handler.
 
 Note that even when an error (or unlink) is reported, data may have been
 transferred.  That's because USB transfers are packetized; it might take
@@ -210,12 +209,12 @@ have transferred successfully before the completion was called.
 
 
 NOTE:  ***** WARNING *****
-NEVER SLEEP IN A COMPLETION HANDLER.  These are normally called
-during hardware interrupt processing.  If you can, defer substantial
-work to a tasklet (bottom half) to keep system latencies low.  You'll
-probably need to use spinlocks to protect data structures you manipulate
-in completion handlers.
+NEVER SLEEP IN A COMPLETION HANDLER.  These are often called in atomic
+context.
 
+In the current kernel, completion handlers run with local interrupts
+disabled, but in the future this will be changed, so don't assume that
+local IRQs are always disabled inside completion handlers.
 
 1.8. How to do isochronous (ISO) transfers?
 
diff --git a/Documentation/usb/proc_usb_info.txt b/Documentation/usb/proc_usb_info.txt
index c9c3f0f..98be919 100644
--- a/Documentation/usb/proc_usb_info.txt
+++ b/Documentation/usb/proc_usb_info.txt
@@ -54,9 +54,12 @@ it and 002/048 sometime later.
 
 These files can be read as binary data.  The binary data consists
 of first the device descriptor, then the descriptors for each
-configuration of the device.  Multi-byte fields in the device and
-configuration descriptors, but not other descriptors, are converted
-to host endianness by the kernel.  This information is also shown
+configuration of the device.  Multi-byte fields in the device descriptor
+are converted to host endianness by the kernel.  The configuration
+descriptors are in bus endian format! The configuration descriptor
+are wTotalLength bytes apart. If a device returns less configuration
+descriptor data than indicated by wTotalLength there will be a hole in
+the file for the missing bytes.  This information is also shown
 in text form by the /proc/bus/usb/devices file, described later.
 
 These files may also be used to write user-level drivers for the USB