diff options
Diffstat (limited to 'Documentation/virtual/kvm/api.txt')
-rw-r--r-- | Documentation/virtual/kvm/api.txt | 49 |
1 files changed, 41 insertions, 8 deletions
diff --git a/Documentation/virtual/kvm/api.txt b/Documentation/virtual/kvm/api.txt index 6cd63a9..a9380ba5 100644 --- a/Documentation/virtual/kvm/api.txt +++ b/Documentation/virtual/kvm/api.txt @@ -586,8 +586,8 @@ struct kvm_fpu { 4.24 KVM_CREATE_IRQCHIP -Capability: KVM_CAP_IRQCHIP -Architectures: x86, ia64, ARM, arm64 +Capability: KVM_CAP_IRQCHIP, KVM_CAP_S390_IRQCHIP (s390) +Architectures: x86, ia64, ARM, arm64, s390 Type: vm ioctl Parameters: none Returns: 0 on success, -1 on error @@ -596,7 +596,10 @@ Creates an interrupt controller model in the kernel. On x86, creates a virtual ioapic, a virtual PIC (two PICs, nested), and sets up future vcpus to have a local APIC. IRQ routing for GSIs 0-15 is set to both PIC and IOAPIC; GSI 16-23 only go to the IOAPIC. On ia64, a IOSAPIC is created. On ARM/arm64, a GIC is -created. +created. On s390, a dummy irq routing table is created. + +Note that on s390 the KVM_CAP_S390_IRQCHIP vm capability needs to be enabled +before KVM_CREATE_IRQCHIP can be used. 4.25 KVM_IRQ_LINE @@ -612,6 +615,20 @@ On some architectures it is required that an interrupt controller model has been previously created with KVM_CREATE_IRQCHIP. Note that edge-triggered interrupts require the level to be set to 1 and then back to 0. +On real hardware, interrupt pins can be active-low or active-high. This +does not matter for the level field of struct kvm_irq_level: 1 always +means active (asserted), 0 means inactive (deasserted). + +x86 allows the operating system to program the interrupt polarity +(active-low/active-high) for level-triggered interrupts, and KVM used +to consider the polarity. However, due to bitrot in the handling of +active-low interrupts, the above convention is now valid on x86 too. +This is signaled by KVM_CAP_X86_IOAPIC_POLARITY_IGNORED. Userspace +should not present interrupts to the guest as active-low unless this +capability is present (or unless it is not using the in-kernel irqchip, +of course). + + ARM/arm64 can signal an interrupt either at the CPU level, or at the in-kernel irqchip (GIC), and for in-kernel irqchip can tell the GIC to use PPIs designated for specific cpus. The irq field is interpreted @@ -628,7 +645,7 @@ The irq_type field has the following values: (The irq_id field thus corresponds nicely to the IRQ ID in the ARM GIC specs) -In both cases, level is used to raise/lower the line. +In both cases, level is used to assert/deassert the line. struct kvm_irq_level { union { @@ -918,9 +935,9 @@ documentation when it pops into existence). 4.37 KVM_ENABLE_CAP -Capability: KVM_CAP_ENABLE_CAP +Capability: KVM_CAP_ENABLE_CAP, KVM_CAP_ENABLE_CAP_VM Architectures: ppc, s390 -Type: vcpu ioctl +Type: vcpu ioctl, vm ioctl (with KVM_CAP_ENABLE_CAP_VM) Parameters: struct kvm_enable_cap (in) Returns: 0 on success; -1 on error @@ -951,6 +968,8 @@ function properly, this is the place to put them. __u8 pad[64]; }; +The vcpu ioctl should be used for vcpu-specific capabilities, the vm ioctl +for vm-wide capabilities. 4.38 KVM_GET_MP_STATE @@ -1320,7 +1339,7 @@ KVM_ASSIGN_DEV_IRQ. Partial deassignment of host or guest IRQ is allowed. 4.52 KVM_SET_GSI_ROUTING Capability: KVM_CAP_IRQ_ROUTING -Architectures: x86 ia64 +Architectures: x86 ia64 s390 Type: vm ioctl Parameters: struct kvm_irq_routing (in) Returns: 0 on success, -1 on error @@ -1343,6 +1362,7 @@ struct kvm_irq_routing_entry { union { struct kvm_irq_routing_irqchip irqchip; struct kvm_irq_routing_msi msi; + struct kvm_irq_routing_s390_adapter adapter; __u32 pad[8]; } u; }; @@ -1350,6 +1370,7 @@ struct kvm_irq_routing_entry { /* gsi routing entry types */ #define KVM_IRQ_ROUTING_IRQCHIP 1 #define KVM_IRQ_ROUTING_MSI 2 +#define KVM_IRQ_ROUTING_S390_ADAPTER 3 No flags are specified so far, the corresponding field must be set to zero. @@ -1365,6 +1386,14 @@ struct kvm_irq_routing_msi { __u32 pad; }; +struct kvm_irq_routing_s390_adapter { + __u64 ind_addr; + __u64 summary_addr; + __u64 ind_offset; + __u32 summary_offset; + __u32 adapter_id; +}; + 4.53 KVM_ASSIGN_SET_MSIX_NR @@ -1462,7 +1491,7 @@ struct kvm_lapic_state { char regs[KVM_APIC_REG_SIZE]; }; -Copies the input argument into the the Local APIC registers. The data format +Copies the input argument into the Local APIC registers. The data format and layout are the same as documented in the architecture manual. @@ -2566,6 +2595,10 @@ executed a memory-mapped I/O instruction which could not be satisfied by kvm. The 'data' member contains the written data if 'is_write' is true, and should be filled by application code otherwise. +The 'data' member contains, in its first 'len' bytes, the value as it would +appear if the VCPU performed a load or store of the appropriate width directly +to the byte array. + NOTE: For KVM_EXIT_IO, KVM_EXIT_MMIO, KVM_EXIT_OSI, KVM_EXIT_DCR, KVM_EXIT_PAPR and KVM_EXIT_EPR the corresponding operations are complete (and guest state is consistent) only after userspace |