diff options
Diffstat (limited to 'Documentation/networking')
| -rw-r--r-- | Documentation/networking/alias.txt | 25 | ||||
| -rw-r--r-- | Documentation/networking/ipv6.txt | 35 | ||||
| -rw-r--r-- | Documentation/networking/netconsole.txt | 3 |
3 files changed, 43 insertions, 20 deletions
diff --git a/Documentation/networking/alias.txt b/Documentation/networking/alias.txt index cd12c2f..85046f5 100644 --- a/Documentation/networking/alias.txt +++ b/Documentation/networking/alias.txt @@ -2,13 +2,13 @@ IP-Aliasing: ============ -IP-aliases are additional IP-addresses/masks hooked up to a base -interface by adding a colon and a string when running ifconfig. -This string is usually numeric, but this is not a must. - -IP-Aliases are avail if CONFIG_INET (`standard' IPv4 networking) -is configured in the kernel. +IP-aliases are an obsolete way to manage multiple IP-addresses/masks +per interface. Newer tools such as iproute2 support multiple +address/prefixes per interface, but aliases are still supported +for backwards compatibility. +An alias is formed by adding a colon and a string when running ifconfig. +This string is usually numeric, but this is not a must. o Alias creation. Alias creation is done by 'magic' interface naming: eg. to create a @@ -38,16 +38,3 @@ o Relationship with main device If the base device is shut down the added aliases will be deleted too. - - -Contact -------- -Please finger or e-mail me: - Juan Jose Ciarlante <jjciarla@raiz.uncu.edu.ar> - -Updated by Erik Schoenfelder <schoenfr@gaertner.DE> - -; local variables: -; mode: indented-text -; mode: auto-fill -; end: diff --git a/Documentation/networking/ipv6.txt b/Documentation/networking/ipv6.txt new file mode 100644 index 0000000..268e5c1 --- /dev/null +++ b/Documentation/networking/ipv6.txt @@ -0,0 +1,35 @@ + +Options for the ipv6 module are supplied as parameters at load time. + +Module options may be given as command line arguments to the insmod +or modprobe command, but are usually specified in either the +/etc/modules.conf or /etc/modprobe.conf configuration file, or in a +distro-specific configuration file. + +The available ipv6 module parameters are listed below. If a parameter +is not specified the default value is used. + +The parameters are as follows: + +disable + + Specifies whether to load the IPv6 module, but disable all + its functionality. This might be used when another module + has a dependency on the IPv6 module being loaded, but no + IPv6 addresses or operations are desired. + + The possible values and their effects are: + + 0 + IPv6 is enabled. + + This is the default value. + + 1 + IPv6 is disabled. + + No IPv6 addresses will be added to interfaces, and + it will not be possible to open an IPv6 socket. + + A reboot is required to enable IPv6. + diff --git a/Documentation/networking/netconsole.txt b/Documentation/networking/netconsole.txt index 3c2f2b3..8d02207 100644 --- a/Documentation/networking/netconsole.txt +++ b/Documentation/networking/netconsole.txt @@ -51,7 +51,8 @@ Built-in netconsole starts immediately after the TCP stack is initialized and attempts to bring up the supplied dev at the supplied address. -The remote host can run either 'netcat -u -l -p <port>' or syslogd. +The remote host can run either 'netcat -u -l -p <port>', +'nc -l -u <port>' or syslogd. Dynamic reconfiguration: ======================== |
