summaryrefslogtreecommitdiffstats
path: root/Documentation/networking/bonding.txt
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/networking/bonding.txt')
-rw-r--r--Documentation/networking/bonding.txt68
1 files changed, 61 insertions, 7 deletions
diff --git a/Documentation/networking/bonding.txt b/Documentation/networking/bonding.txt
index 688dfe1..5ede747 100644
--- a/Documentation/networking/bonding.txt
+++ b/Documentation/networking/bonding.txt
@@ -194,6 +194,48 @@ or, for backwards compatibility, the option value. E.g.,
The parameters are as follows:
+ad_select
+
+ Specifies the 802.3ad aggregation selection logic to use. The
+ possible values and their effects are:
+
+ stable or 0
+
+ The active aggregator is chosen by largest aggregate
+ bandwidth.
+
+ Reselection of the active aggregator occurs only when all
+ slaves of the active aggregator are down or the active
+ aggregator has no slaves.
+
+ This is the default value.
+
+ bandwidth or 1
+
+ The active aggregator is chosen by largest aggregate
+ bandwidth. Reselection occurs if:
+
+ - A slave is added to or removed from the bond
+
+ - Any slave's link state changes
+
+ - Any slave's 802.3ad association state changes
+
+ - The bond's adminstrative state changes to up
+
+ count or 2
+
+ The active aggregator is chosen by the largest number of
+ ports (slaves). Reselection occurs as described under the
+ "bandwidth" setting, above.
+
+ The bandwidth and count selection policies permit failover of
+ 802.3ad aggregations when partial failure of the active aggregator
+ occurs. This keeps the aggregator with the highest availability
+ (either in bandwidth or in number of ports) active at all times.
+
+ This option was added in bonding version 3.4.0.
+
arp_interval
Specifies the ARP link monitoring frequency in milliseconds.
@@ -551,6 +593,16 @@ num_grat_arp
affects only the active-backup mode. This option was added for
bonding version 3.3.0.
+num_unsol_na
+
+ Specifies the number of unsolicited IPv6 Neighbor Advertisements
+ to be issued after a failover event. One unsolicited NA is issued
+ immediately after the failover.
+
+ The valid range is 0 - 255; the default value is 1. This option
+ affects only the active-backup mode. This option was added for
+ bonding version 3.4.0.
+
primary
A string (eth0, eth2, etc) specifying which slave is the
@@ -922,17 +974,19 @@ USERCTL=no
NETMASK, NETWORK and BROADCAST) to match your network configuration.
For later versions of initscripts, such as that found with Fedora
-7 and Red Hat Enterprise Linux version 5 (or later), it is possible, and,
-indeed, preferable, to specify the bonding options in the ifcfg-bond0
+7 (or later) and Red Hat Enterprise Linux version 5 (or later), it is possible,
+and, indeed, preferable, to specify the bonding options in the ifcfg-bond0
file, e.g. a line of the format:
-BONDING_OPTS="mode=active-backup arp_interval=60 arp_ip_target=+192.168.1.254"
+BONDING_OPTS="mode=active-backup arp_interval=60 arp_ip_target=192.168.1.254"
will configure the bond with the specified options. The options
specified in BONDING_OPTS are identical to the bonding module parameters
-except for the arp_ip_target field. Each target should be included as a
-separate option and should be preceded by a '+' to indicate it should be
-added to the list of queried targets, e.g.,
+except for the arp_ip_target field when using versions of initscripts older
+than and 8.57 (Fedora 8) and 8.45.19 (Red Hat Enterprise Linux 5.2). When
+using older versions each target should be included as a separate option and
+should be preceded by a '+' to indicate it should be added to the list of
+queried targets, e.g.,
arp_ip_target=+192.168.1.1 arp_ip_target=+192.168.1.2
@@ -940,7 +994,7 @@ added to the list of queried targets, e.g.,
options via BONDING_OPTS, it is not necessary to edit /etc/modules.conf or
/etc/modprobe.conf.
- For older versions of initscripts that do not support
+ For even older versions of initscripts that do not support
BONDING_OPTS, it is necessary to edit /etc/modules.conf (or
/etc/modprobe.conf, depending upon your distro) to load the bonding module
with your desired options when the bond0 interface is brought up. The
OpenPOWER on IntegriCloud