diff options
Diffstat (limited to 'Documentation/kernel-parameters.txt')
| -rw-r--r-- | Documentation/kernel-parameters.txt | 39 |
1 files changed, 37 insertions, 2 deletions
diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index 2443f5b..0f1544f 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -690,7 +690,7 @@ and is between 256 and 4096 characters. It is defined in the file See Documentation/block/as-iosched.txt and Documentation/block/deadline-iosched.txt for details. - elfcorehdr= [X86-32, X86_64] + elfcorehdr= [IA64,PPC,SH,X86-32,X86_64] Specifies physical address of start of kernel core image elf header. Generally kexec loader will pass this option to capture kernel. @@ -796,6 +796,9 @@ and is between 256 and 4096 characters. It is defined in the file Defaults to the default architecture's huge page size if not specified. + hlt [BUGS=ARM,SH] + + i8042.debug [HW] Toggle i8042 debug mode i8042.direct [HW] Put keyboard port into non-translated mode i8042.dumbkbd [HW] Pretend that controller can only read data from keyboard and cannot control its state @@ -1210,6 +1213,10 @@ and is between 256 and 4096 characters. It is defined in the file mem=nopentium [BUGS=X86-32] Disable usage of 4MB pages for kernel memory. + memchunk=nn[KMG] + [KNL,SH] Allow user to override the default size for + per-device physically contiguous DMA buffers. + memmap=exactmap [KNL,X86-32,X86_64] Enable setting of an exact E820 memory map, as specified by the user. Such memmap=exactmap lines can be constructed based on @@ -1392,6 +1399,8 @@ and is between 256 and 4096 characters. It is defined in the file nodisconnect [HW,SCSI,M68K] Disables SCSI disconnects. + nodsp [SH] Disable hardware DSP at boot time. + noefi [X86-32,X86-64] Disable EFI runtime services support. noexec [IA-64] @@ -1408,13 +1417,15 @@ and is between 256 and 4096 characters. It is defined in the file noexec32=off: disable non-executable mappings read implies executable mappings + nofpu [SH] Disable hardware FPU at boot time. + nofxsr [BUGS=X86-32] Disables x86 floating point extended register save and restore. The kernel will only save legacy floating-point registers on task switch. noclflush [BUGS=X86] Don't use the CLFLUSH instruction - nohlt [BUGS=ARM] + nohlt [BUGS=ARM,SH] no-hlt [BUGS=X86-32] Tells the kernel that the hlt instruction doesn't work correctly and not to @@ -1713,6 +1724,11 @@ and is between 256 and 4096 characters. It is defined in the file autoconfiguration. Ranges are in pairs (memory base and size). + dynamic_printk + Enables pr_debug()/dev_dbg() calls if + CONFIG_DYNAMIC_PRINTK_DEBUG has been enabled. These can also + be switched on/off via <debugfs>/dynamic_printk/modules + print-fatal-signals= [KNL] debug: print fatal signals print-fatal-signals=1: print segfault info to @@ -2247,6 +2263,25 @@ and is between 256 and 4096 characters. It is defined in the file autosuspended. Devices for which the delay is set to a negative value won't be autosuspended at all. + usbcore.usbfs_snoop= + [USB] Set to log all usbfs traffic (default 0 = off). + + usbcore.blinkenlights= + [USB] Set to cycle leds on hubs (default 0 = off). + + usbcore.old_scheme_first= + [USB] Start with the old device initialization + scheme (default 0 = off). + + usbcore.use_both_schemes= + [USB] Try the other device initialization scheme + if the first one fails (default 1 = enabled). + + usbcore.initial_descriptor_timeout= + [USB] Specifies timeout for the initial 64-byte + USB_REQ_GET_DESCRIPTOR request in milliseconds + (default 5000 = 5.0 seconds). + usbhid.mousepoll= [USBHID] The interval which mice are to be polled at. |
