diff options
Diffstat (limited to 'Documentation/ibm-acpi.txt')
| -rw-r--r-- | Documentation/ibm-acpi.txt | 65 |
1 files changed, 46 insertions, 19 deletions
diff --git a/Documentation/ibm-acpi.txt b/Documentation/ibm-acpi.txt index 333b8eb..cbd3a60 100644 --- a/Documentation/ibm-acpi.txt +++ b/Documentation/ibm-acpi.txt @@ -571,27 +571,57 @@ directly accesses hardware registers and may not work as expected. USE WITH CAUTION! To use this feature, you need to supply the experimental=1 parameter when loading the module. -This feature attempts to show the current fan speed. The speed is read -directly from the hardware registers of the embedded controller. This -is known to work on later R, T and X series ThinkPads but may show a -bogus value on other models. +This feature attempts to show the current fan speed, control mode and +other fan data that might be available. The speed is read directly +from the hardware registers of the embedded controller. This is known +to work on later R, T and X series ThinkPads but may show a bogus +value on other models. + +Most ThinkPad fans work in "levels". Level 0 stops the fan. The higher +the level, the higher the fan speed, although adjacent levels often map +to the same fan speed. 7 is the highest level, where the fan reaches +the maximum recommended speed. Level "auto" means the EC changes the +fan level according to some internal algorithm, usually based on +readings from the thermal sensors. Level "disengaged" means the EC +disables the speed-locked closed-loop fan control, and drives the fan as +fast as it can go, which might exceed hardware limits, so use this level +with caution. + +The fan usually ramps up or down slowly from one speed to another, +and it is normal for the EC to take several seconds to react to fan +commands. The fan may be enabled or disabled with the following commands: echo enable >/proc/acpi/ibm/fan echo disable >/proc/acpi/ibm/fan +Placing a fan on level 0 is the same as disabling it. Enabling a fan +will try to place it in a safe level if it is too slow or disabled. + WARNING WARNING WARNING: do not leave the fan disabled unless you are -monitoring the temperature sensor readings and you are ready to enable -it if necessary to avoid overheating. +monitoring all of the temperature sensor readings and you are ready to +enable it if necessary to avoid overheating. + +An enabled fan in level "auto" may stop spinning if the EC decides the +ThinkPad is cool enough and doesn't need the extra airflow. This is +normal, and the EC will spin the fan up if the varios thermal readings +rise too much. + +On the X40, this seems to depend on the CPU and HDD temperatures. +Specifically, the fan is turned on when either the CPU temperature +climbs to 56 degrees or the HDD temperature climbs to 46 degrees. The +fan is turned off when the CPU temperature drops to 49 degrees and the +HDD temperature drops to 41 degrees. These thresholds cannot +currently be controlled. + +The fan level can be controlled with the command: -The fan only runs if it's enabled *and* the various temperature -sensors which control it read high enough. On the X40, this seems to -depend on the CPU and HDD temperatures. Specifically, the fan is -turned on when either the CPU temperature climbs to 56 degrees or the -HDD temperature climbs to 46 degrees. The fan is turned off when the -CPU temperature drops to 49 degrees and the HDD temperature drops to -41 degrees. These thresholds cannot currently be controlled. + echo 'level <level>' > /proc/acpi/ibm/thermal + +Where <level> is an integer from 0 to 7, or one of the words "auto" +or "disengaged" (without the quotes). Not all ThinkPads support the +"auto" and "disengaged" levels. On the X31 and X40 (and ONLY on those models), the fan speed can be controlled to a certain degree. Once the fan is running, it can be @@ -604,12 +634,9 @@ about 3700 to about 7350. Values outside this range either do not have any effect or the fan speed eventually settles somewhere in that range. The fan cannot be stopped or started with this command. -On the 570, temperature readings are not available through this -feature and the fan control works a little differently. The fan speed -is reported in levels from 0 (off) to 7 (max) and can be controlled -with the following command: - - echo 'level <level>' > /proc/acpi/ibm/thermal +The ThinkPad's ACPI DSDT code will reprogram the fan on its own when +certain conditions are met. It will override any fan programming done +through ibm-acpi. EXPERIMENTAL: WAN -- /proc/acpi/ibm/wan --------------------------------------- |
