diff options
Diffstat (limited to 'Documentation/i2c/chips/smsc47b397')
| -rw-r--r-- | Documentation/i2c/chips/smsc47b397 | 158 |
1 files changed, 0 insertions, 158 deletions
diff --git a/Documentation/i2c/chips/smsc47b397 b/Documentation/i2c/chips/smsc47b397 deleted file mode 100644 index da9d80c..0000000 --- a/Documentation/i2c/chips/smsc47b397 +++ /dev/null @@ -1,158 +0,0 @@ -Kernel driver smsc47b397 -======================== - -Supported chips: - * SMSC LPC47B397-NC - Prefix: 'smsc47b397' - Addresses scanned: none, address read from Super I/O config space - Datasheet: In this file - -Authors: Mark M. Hoffman <mhoffman@lightlink.com> - Utilitek Systems, Inc. - -November 23, 2004 - -The following specification describes the SMSC LPC47B397-NC sensor chip -(for which there is no public datasheet available). This document was -provided by Craig Kelly (In-Store Broadcast Network) and edited/corrected -by Mark M. Hoffman <mhoffman@lightlink.com>. - -* * * * * - -Methods for detecting the HP SIO and reading the thermal data on a dc7100. - -The thermal information on the dc7100 is contained in the SIO Hardware Monitor -(HWM). The information is accessed through an index/data pair. The index/data -pair is located at the HWM Base Address + 0 and the HWM Base Address + 1. The -HWM Base address can be obtained from Logical Device 8, registers 0x60 (MSB) -and 0x61 (LSB). Currently we are using 0x480 for the HWM Base Address and -0x480 and 0x481 for the index/data pair. - -Reading temperature information. -The temperature information is located in the following registers: -Temp1 0x25 (Currently, this reflects the CPU temp on all systems). -Temp2 0x26 -Temp3 0x27 -Temp4 0x80 - -Programming Example -The following is an example of how to read the HWM temperature registers: -MOV DX,480H -MOV AX,25H -OUT DX,AL -MOV DX,481H -IN AL,DX - -AL contains the data in hex, the temperature in Celsius is the decimal -equivalent. - -Ex: If AL contains 0x2A, the temperature is 42 degrees C. - -Reading tach information. -The fan speed information is located in the following registers: - LSB MSB -Tach1 0x28 0x29 (Currently, this reflects the CPU - fan speed on all systems). -Tach2 0x2A 0x2B -Tach3 0x2C 0x2D -Tach4 0x2E 0x2F - -Important!!! -Reading the tach LSB locks the tach MSB. -The LSB Must be read first. - -How to convert the tach reading to RPM. -The tach reading (TCount) is given by: (Tach MSB * 256) + (Tach LSB) -The SIO counts the number of 90kHz (11.111us) pulses per revolution. -RPM = 60/(TCount * 11.111us) - -Example: -Reg 0x28 = 0x9B -Reg 0x29 = 0x08 - -TCount = 0x89B = 2203 - -RPM = 60 / (2203 * 11.11111 E-6) = 2451 RPM - -Obtaining the SIO version. - -CONFIGURATION SEQUENCE -To program the configuration registers, the following sequence must be followed: -1. Enter Configuration Mode -2. Configure the Configuration Registers -3. Exit Configuration Mode. - -Enter Configuration Mode -To place the chip into the Configuration State The config key (0x55) is written -to the CONFIG PORT (0x2E). - -Configuration Mode -In configuration mode, the INDEX PORT is located at the CONFIG PORT address and -the DATA PORT is at INDEX PORT address + 1. - -The desired configuration registers are accessed in two steps: -a. Write the index of the Logical Device Number Configuration Register - (i.e., 0x07) to the INDEX PORT and then write the number of the - desired logical device to the DATA PORT. - -b. Write the address of the desired configuration register within the - logical device to the INDEX PORT and then write or read the config- - uration register through the DATA PORT. - -Note: If accessing the Global Configuration Registers, step (a) is not required. - -Exit Configuration Mode -To exit the Configuration State the write 0xAA to the CONFIG PORT (0x2E). -The chip returns to the RUN State. (This is important). - -Programming Example -The following is an example of how to read the SIO Device ID located at 0x20 - -; ENTER CONFIGURATION MODE -MOV DX,02EH -MOV AX,055H -OUT DX,AL -; GLOBAL CONFIGURATION REGISTER -MOV DX,02EH -MOV AL,20H -OUT DX,AL -; READ THE DATA -MOV DX,02FH -IN AL,DX -; EXIT CONFIGURATION MODE -MOV DX,02EH -MOV AX,0AAH -OUT DX,AL - -The registers of interest for identifying the SIO on the dc7100 are Device ID -(0x20) and Device Rev (0x21). - -The Device ID will read 0X6F -The Device Rev currently reads 0x01 - -Obtaining the HWM Base Address. -The following is an example of how to read the HWM Base Address located in -Logical Device 8. - -; ENTER CONFIGURATION MODE -MOV DX,02EH -MOV AX,055H -OUT DX,AL -; CONFIGURE REGISTER CRE0, -; LOGICAL DEVICE 8 -MOV DX,02EH -MOV AL,07H -OUT DX,AL ;Point to LD# Config Reg -MOV DX,02FH -MOV AL, 08H -OUT DX,AL;Point to Logical Device 8 -; -MOV DX,02EH -MOV AL,60H -OUT DX,AL ; Point to HWM Base Addr MSB -MOV DX,02FH -IN AL,DX ; Get MSB of HWM Base Addr -; EXIT CONFIGURATION MODE -MOV DX,02EH -MOV AX,0AAH -OUT DX,AL |
