diff options
Diffstat (limited to 'Documentation/filesystems')
| -rw-r--r-- | Documentation/filesystems/nfs-rdma.txt | 75 |
1 files changed, 44 insertions, 31 deletions
diff --git a/Documentation/filesystems/nfs-rdma.txt b/Documentation/filesystems/nfs-rdma.txt index d0ec45a..9ad453d 100644 --- a/Documentation/filesystems/nfs-rdma.txt +++ b/Documentation/filesystems/nfs-rdma.txt @@ -5,7 +5,7 @@ ################################################################################ Author: NetApp and Open Grid Computing - Date: April 15, 2008 + Date: May 29, 2008 Table of Contents ~~~~~~~~~~~~~~~~~ @@ -60,16 +60,18 @@ Installation The procedures described in this document have been tested with distributions from Red Hat's Fedora Project (http://fedora.redhat.com/). - - Install nfs-utils-1.1.1 or greater on the client + - Install nfs-utils-1.1.2 or greater on the client - An NFS/RDMA mount point can only be obtained by using the mount.nfs - command in nfs-utils-1.1.1 or greater. To see which version of mount.nfs - you are using, type: + An NFS/RDMA mount point can be obtained by using the mount.nfs command in + nfs-utils-1.1.2 or greater (nfs-utils-1.1.1 was the first nfs-utils version + with support for NFS/RDMA mounts, but for various reasons we recommend using + nfs-utils-1.1.2 or greater). To see which version of mount.nfs you are + using, type: - > /sbin/mount.nfs -V + $ /sbin/mount.nfs -V - If the version is less than 1.1.1 or the command does not exist, - then you will need to install the latest version of nfs-utils. + If the version is less than 1.1.2 or the command does not exist, + you should install the latest version of nfs-utils. Download the latest package from: @@ -77,22 +79,32 @@ Installation Uncompress the package and follow the installation instructions. - If you will not be using GSS and NFSv4, the installation process - can be simplified by disabling these features when running configure: + If you will not need the idmapper and gssd executables (you do not need + these to create an NFS/RDMA enabled mount command), the installation + process can be simplified by disabling these features when running + configure: - > ./configure --disable-gss --disable-nfsv4 + $ ./configure --disable-gss --disable-nfsv4 - For more information on this see the package's README and INSTALL files. + To build nfs-utils you will need the tcp_wrappers package installed. For + more information on this see the package's README and INSTALL files. After building the nfs-utils package, there will be a mount.nfs binary in the utils/mount directory. This binary can be used to initiate NFS v2, v3, or v4 mounts. To initiate a v4 mount, the binary must be called mount.nfs4. The standard technique is to create a symlink called mount.nfs4 to mount.nfs. - NOTE: mount.nfs and therefore nfs-utils-1.1.1 or greater is only needed + This mount.nfs binary should be installed at /sbin/mount.nfs as follows: + + $ sudo cp utils/mount/mount.nfs /sbin/mount.nfs + + In this location, mount.nfs will be invoked automatically for NFS mounts + by the system mount commmand. + + NOTE: mount.nfs and therefore nfs-utils-1.1.2 or greater is only needed on the NFS client machine. You do not need this specific version of nfs-utils on the server. Furthermore, only the mount.nfs command from - nfs-utils-1.1.1 is needed on the client. + nfs-utils-1.1.2 is needed on the client. - Install a Linux kernel with NFS/RDMA @@ -156,8 +168,8 @@ Check RDMA and NFS Setup this time. For example, if you are using a Mellanox Tavor/Sinai/Arbel card: - > modprobe ib_mthca - > modprobe ib_ipoib + $ modprobe ib_mthca + $ modprobe ib_ipoib If you are using InfiniBand, make sure there is a Subnet Manager (SM) running on the network. If your IB switch has an embedded SM, you can @@ -166,7 +178,7 @@ Check RDMA and NFS Setup If an SM is running on your network, you should see the following: - > cat /sys/class/infiniband/driverX/ports/1/state + $ cat /sys/class/infiniband/driverX/ports/1/state 4: ACTIVE where driverX is mthca0, ipath5, ehca3, etc. @@ -174,10 +186,10 @@ Check RDMA and NFS Setup To further test the InfiniBand software stack, use IPoIB (this assumes you have two IB hosts named host1 and host2): - host1> ifconfig ib0 a.b.c.x - host2> ifconfig ib0 a.b.c.y - host1> ping a.b.c.y - host2> ping a.b.c.x + host1$ ifconfig ib0 a.b.c.x + host2$ ifconfig ib0 a.b.c.y + host1$ ping a.b.c.y + host2$ ping a.b.c.x For other device types, follow the appropriate procedures. @@ -214,9 +226,9 @@ NFS/RDMA Setup For InfiniBand using a Mellanox adapter: - > modprobe ib_mthca - > modprobe ib_ipoib - > ifconfig ib0 a.b.c.d + $ modprobe ib_mthca + $ modprobe ib_ipoib + $ ifconfig ib0 a.b.c.d NOTE: use unique addresses for the client and server @@ -225,30 +237,31 @@ NFS/RDMA Setup If the NFS/RDMA server was built as a module (CONFIG_SUNRPC_XPRT_RDMA=m in kernel config), load the RDMA transport module: - > modprobe svcrdma + $ modprobe svcrdma Regardless of how the server was built (module or built-in), start the server: - > /etc/init.d/nfs start + $ /etc/init.d/nfs start or - > service nfs start + $ service nfs start Instruct the server to listen on the RDMA transport: - > echo rdma 2050 > /proc/fs/nfsd/portlist + $ echo rdma 2050 > /proc/fs/nfsd/portlist - On the client system If the NFS/RDMA client was built as a module (CONFIG_SUNRPC_XPRT_RDMA=m in kernel config), load the RDMA client module: - > modprobe xprtrdma.ko + $ modprobe xprtrdma.ko - Regardless of how the client was built (module or built-in), issue the mount.nfs command: + Regardless of how the client was built (module or built-in), use this command to + mount the NFS/RDMA server: - > /path/to/your/mount.nfs <IPoIB-server-name-or-address>:/<export> /mnt -i -o rdma,port=2050 + $ mount -o rdma,port=2050 <IPoIB-server-name-or-address>:/<export> /mnt To verify that the mount is using RDMA, run "cat /proc/mounts" and check the "proto" field for the given mount. |
