diff options
Diffstat (limited to 'Documentation/devicetree')
118 files changed, 3609 insertions, 83 deletions
diff --git a/Documentation/devicetree/bindings/arc/interrupts.txt b/Documentation/devicetree/bindings/arc/interrupts.txt new file mode 100644 index 0000000..9a5d562 --- /dev/null +++ b/Documentation/devicetree/bindings/arc/interrupts.txt @@ -0,0 +1,24 @@ +* ARC700 incore Interrupt Controller + + The core interrupt controller provides 32 prioritised interrupts (2 levels) + to ARC700 core. + +Properties: + +- compatible: "snps,arc700-intc" +- interrupt-controller: This is an interrupt controller. +- #interrupt-cells: Must be <1>. + + Single Cell "interrupts" property of a device specifies the IRQ number + between 0 to 31 + + intc accessed via the special ARC AUX register interface, hence "reg" property + is not specified. + +Example: + + intc: interrupt-controller { + compatible = "snps,arc700-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/arm/altera/socfpga-system.txt b/Documentation/devicetree/bindings/arm/altera/socfpga-system.txt index 07c65e3..f4d04a0 100644 --- a/Documentation/devicetree/bindings/arm/altera/socfpga-system.txt +++ b/Documentation/devicetree/bindings/arm/altera/socfpga-system.txt @@ -3,9 +3,11 @@ Altera SOCFPGA System Manager Required properties: - compatible : "altr,sys-mgr" - reg : Should contain 1 register ranges(address and length) +- cpu1-start-addr : CPU1 start address in hex. Example: sysmgr@ffd08000 { compatible = "altr,sys-mgr"; reg = <0xffd08000 0x1000>; + cpu1-start-addr = <0xffd080c4>; }; diff --git a/Documentation/devicetree/bindings/arm/arch_timer.txt b/Documentation/devicetree/bindings/arm/arch_timer.txt index 52478c8..20746e5 100644 --- a/Documentation/devicetree/bindings/arm/arch_timer.txt +++ b/Documentation/devicetree/bindings/arm/arch_timer.txt @@ -1,13 +1,14 @@ * ARM architected timer -ARM Cortex-A7 and Cortex-A15 have a per-core architected timer, which -provides per-cpu timers. +ARM cores may have a per-core architected timer, which provides per-cpu timers. The timer is attached to a GIC to deliver its per-processor interrupts. ** Timer node properties: -- compatible : Should at least contain "arm,armv7-timer". +- compatible : Should at least contain one of + "arm,armv7-timer" + "arm,armv8-timer" - interrupts : Interrupt list for secure, non-secure, virtual and hypervisor timers, in that order. diff --git a/Documentation/devicetree/bindings/arm/armadeus.txt b/Documentation/devicetree/bindings/arm/armadeus.txt new file mode 100644 index 0000000..9821283 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/armadeus.txt @@ -0,0 +1,6 @@ +Armadeus i.MX Platforms Device Tree Bindings +----------------------------------------------- + +APF51: i.MX51 based module. +Required root node properties: + - compatible = "armadeus,imx51-apf51", "fsl,imx51"; diff --git a/Documentation/devicetree/bindings/arm/atmel-aic.txt b/Documentation/devicetree/bindings/arm/atmel-aic.txt index 19078bf..ad03121 100644 --- a/Documentation/devicetree/bindings/arm/atmel-aic.txt +++ b/Documentation/devicetree/bindings/arm/atmel-aic.txt @@ -4,7 +4,7 @@ Required properties: - compatible: Should be "atmel,<chip>-aic" - interrupt-controller: Identifies the node as an interrupt controller. - interrupt-parent: For single AIC system, it is an empty property. -- #interrupt-cells: The number of cells to define the interrupts. It sould be 3. +- #interrupt-cells: The number of cells to define the interrupts. It should be 3. The first cell is the IRQ number (aka "Peripheral IDentifier" on datasheet). The second cell is used to specify flags: bits[3:0] trigger type and level flags: diff --git a/Documentation/devicetree/bindings/arm/fsl.txt b/Documentation/devicetree/bindings/arm/fsl.txt index f798187..e935d7d 100644 --- a/Documentation/devicetree/bindings/arm/fsl.txt +++ b/Documentation/devicetree/bindings/arm/fsl.txt @@ -5,6 +5,14 @@ i.MX23 Evaluation Kit Required root node properties: - compatible = "fsl,imx23-evk", "fsl,imx23"; +i.MX25 Product Development Kit +Required root node properties: + - compatible = "fsl,imx25-pdk", "fsl,imx25"; + +i.MX27 Product Development Kit +Required root node properties: + - compatible = "fsl,imx27-pdk", "fsl,imx27"; + i.MX28 Evaluation Kit Required root node properties: - compatible = "fsl,imx28-evk", "fsl,imx28"; diff --git a/Documentation/devicetree/bindings/arm/gic.txt b/Documentation/devicetree/bindings/arm/gic.txt index 62eb8df..3dfb0c0 100644 --- a/Documentation/devicetree/bindings/arm/gic.txt +++ b/Documentation/devicetree/bindings/arm/gic.txt @@ -42,7 +42,7 @@ Main node required properties: Optional - interrupts : Interrupt source of the parent interrupt controller on - secondary GICs, or VGIC maintainance interrupt on primary GIC (see + secondary GICs, or VGIC maintenance interrupt on primary GIC (see below). - cpu-offset : per-cpu offset within the distributor and cpu interface @@ -74,7 +74,7 @@ Required properties: virtual interface control register base and size. The 2nd additional region is the GIC virtual cpu interface register base and size. -- interrupts : VGIC maintainance interrupt. +- interrupts : VGIC maintenance interrupt. Example: diff --git a/Documentation/devicetree/bindings/arm/kirkwood.txt b/Documentation/devicetree/bindings/arm/kirkwood.txt new file mode 100644 index 0000000..98cce9a --- /dev/null +++ b/Documentation/devicetree/bindings/arm/kirkwood.txt @@ -0,0 +1,27 @@ +Marvell Kirkwood Platforms Device Tree Bindings +----------------------------------------------- + +Boards with a SoC of the Marvell Kirkwood +shall have the following property: + +Required root node property: + +compatible: must contain "marvell,kirkwood"; + +In order to support the kirkwood cpufreq driver, there must be a node +cpus/cpu@0 with three clocks, "cpu_clk", "ddrclk" and "powersave", +where the "powersave" clock is a gating clock used to switch the CPU +between the "cpu_clk" and the "ddrclk". + +Example: + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + device_type = "cpu"; + compatible = "marvell,sheeva-88SV131"; + clocks = <&core_clk 1>, <&core_clk 3>, <&gate_clk 11>; + clock-names = "cpu_clk", "ddrclk", "powersave"; + }; diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt index d0051a7..f8288ea 100644 --- a/Documentation/devicetree/bindings/arm/omap/omap.txt +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -39,16 +39,16 @@ Boards: - OMAP3 Tobi with Overo : Commercial expansion board with daughter board compatible = "ti,omap3-tobi", "ti,omap3-overo", "ti,omap3" -- OMAP4 SDP : Software Developement Board +- OMAP4 SDP : Software Development Board compatible = "ti,omap4-sdp", "ti,omap4430" - OMAP4 PandaBoard : Low cost community board compatible = "ti,omap4-panda", "ti,omap4430" -- OMAP3 EVM : Software Developement Board for OMAP35x, AM/DM37x +- OMAP3 EVM : Software Development Board for OMAP35x, AM/DM37x compatible = "ti,omap3-evm", "ti,omap3" -- AM335X EVM : Software Developement Board for AM335x +- AM335X EVM : Software Development Board for AM335x compatible = "ti,am335x-evm", "ti,am33xx", "ti,omap3" - AM335X Bone : Low cost community board diff --git a/Documentation/devicetree/bindings/arm/psci.txt b/Documentation/devicetree/bindings/arm/psci.txt new file mode 100644 index 0000000..433afe9 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/psci.txt @@ -0,0 +1,55 @@ +* Power State Coordination Interface (PSCI) + +Firmware implementing the PSCI functions described in ARM document number +ARM DEN 0022A ("Power State Coordination Interface System Software on ARM +processors") can be used by Linux to initiate various CPU-centric power +operations. + +Issue A of the specification describes functions for CPU suspend, hotplug +and migration of secure software. + +Functions are invoked by trapping to the privilege level of the PSCI +firmware (specified as part of the binding below) and passing arguments +in a manner similar to that specified by AAPCS: + + r0 => 32-bit Function ID / return value + {r1 - r3} => Parameters + +Note that the immediate field of the trapping instruction must be set +to #0. + + +Main node required properties: + + - compatible : Must be "arm,psci" + + - method : The method of calling the PSCI firmware. Permitted + values are: + + "smc" : SMC #0, with the register assignments specified + in this binding. + + "hvc" : HVC #0, with the register assignments specified + in this binding. + +Main node optional properties: + + - cpu_suspend : Function ID for CPU_SUSPEND operation + + - cpu_off : Function ID for CPU_OFF operation + + - cpu_on : Function ID for CPU_ON operation + + - migrate : Function ID for MIGRATE operation + + +Example: + + psci { + compatible = "arm,psci"; + method = "smc"; + cpu_suspend = <0x95c10000>; + cpu_off = <0x95c10001>; + cpu_on = <0x95c10002>; + migrate = <0x95c10003>; + }; diff --git a/Documentation/devicetree/bindings/arm/sirf.txt b/Documentation/devicetree/bindings/arm/sirf.txt index 1881e1c..c6ba6d3 100644 --- a/Documentation/devicetree/bindings/arm/sirf.txt +++ b/Documentation/devicetree/bindings/arm/sirf.txt @@ -1,3 +1,9 @@ -prima2 "cb" evaluation board +CSR SiRFprimaII and SiRFmarco device tree bindings. +======================================== + Required root node properties: - - compatible = "sirf,prima2-cb", "sirf,prima2"; + - compatible: + - "sirf,prima2-cb" : prima2 "cb" evaluation board + - "sirf,marco-cb" : marco "cb" evaluation board + - "sirf,prima2" : prima2 device based board + - "sirf,marco" : marco device based board diff --git a/Documentation/devicetree/bindings/arm/ste-nomadik.txt b/Documentation/devicetree/bindings/arm/ste-nomadik.txt new file mode 100644 index 0000000..19bca04 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/ste-nomadik.txt @@ -0,0 +1,27 @@ +ST-Ericsson Nomadik Device Tree Bindings + +For various board the "board" node may contain specific properties +that pertain to this particular board, such as board-specific GPIOs. + +Boards with the Nomadik SoC include: + +S8815 "MiniKit" manufactured by Calao Systems: + +Required root node property: + +compatible="calaosystems,usb-s8815"; + +Required node: usb-s8815 + +Example: + +usb-s8815 { + ethernet-gpio { + gpios = <&gpio3 19 0x1>; + interrupts = <19 0x1>; + interrupt-parent = <&gpio3>; + }; + mmcsd-gpio { + gpios = <&gpio3 16 0x1>; + }; +}; diff --git a/Documentation/devicetree/bindings/arm/tegra.txt b/Documentation/devicetree/bindings/arm/tegra.txt index 6e69d2e..ed9c853 100644 --- a/Documentation/devicetree/bindings/arm/tegra.txt +++ b/Documentation/devicetree/bindings/arm/tegra.txt @@ -1,14 +1,34 @@ NVIDIA Tegra device tree bindings ------------------------------------------- -Boards with the tegra20 SoC shall have the following properties: +SoCs +------------------------------------------- -Required root node property: +Each device tree must specify which Tegra SoC it uses, using one of the +following compatible values: -compatible = "nvidia,tegra20"; + nvidia,tegra20 + nvidia,tegra30 -Boards with the tegra30 SoC shall have the following properties: +Boards +------------------------------------------- -Required root node property: +Each device tree must specify which one or more of the following +board-specific compatible values: -compatible = "nvidia,tegra30"; + ad,medcom-wide + ad,plutux + ad,tamonten + ad,tec + compal,paz00 + compulab,trimslice + nvidia,beaver + nvidia,cardhu + nvidia,cardhu-a02 + nvidia,cardhu-a04 + nvidia,harmony + nvidia,seaboard + nvidia,ventana + nvidia,whistler + toradex,colibri_t20-512 + toradex,iris diff --git a/Documentation/devicetree/bindings/arm/vt8500.txt b/Documentation/devicetree/bindings/arm/vt8500.txt index d657832..87dc1dd 100644 --- a/Documentation/devicetree/bindings/arm/vt8500.txt +++ b/Documentation/devicetree/bindings/arm/vt8500.txt @@ -12,3 +12,11 @@ compatible = "wm,wm8505"; Boards with the Wondermedia WM8650 SoC shall have the following properties: Required root node property: compatible = "wm,wm8650"; + +Boards with the Wondermedia WM8750 SoC shall have the following properties: +Required root node property: +compatible = "wm,wm8750"; + +Boards with the Wondermedia WM8850 SoC shall have the following properties: +Required root node property: +compatible = "wm,wm8850"; diff --git a/Documentation/devicetree/bindings/bus/ti-gpmc.txt b/Documentation/devicetree/bindings/bus/ti-gpmc.txt new file mode 100644 index 0000000..5ddb2e9 --- /dev/null +++ b/Documentation/devicetree/bindings/bus/ti-gpmc.txt @@ -0,0 +1,84 @@ +Device tree bindings for OMAP general purpose memory controllers (GPMC) + +The actual devices are instantiated from the child nodes of a GPMC node. + +Required properties: + + - compatible: Should be set to one of the following: + + ti,omap2420-gpmc (omap2420) + ti,omap2430-gpmc (omap2430) + ti,omap3430-gpmc (omap3430 & omap3630) + ti,omap4430-gpmc (omap4430 & omap4460 & omap543x) + ti,am3352-gpmc (am335x devices) + + - reg: A resource specifier for the register space + (see the example below) + - ti,hwmods: Should be set to "ti,gpmc" until the DT transition is + completed. + - #address-cells: Must be set to 2 to allow memory address translation + - #size-cells: Must be set to 1 to allow CS address passing + - gpmc,num-cs: The maximum number of chip-select lines that controller + can support. + - gpmc,num-waitpins: The maximum number of wait pins that controller can + support. + - ranges: Must be set up to reflect the memory layout with four + integer values for each chip-select line in use: + + <cs-number> 0 <physical address of mapping> <size> + + Currently, calculated values derived from the contents + of the per-CS register GPMC_CONFIG7 (as set up by the + bootloader) are used for the physical address decoding. + As this will change in the future, filling correct + values here is a requirement. + +Timing properties for child nodes. All are optional and default to 0. + + - gpmc,sync-clk: Minimum clock period for synchronous mode, in picoseconds + + Chip-select signal timings corresponding to GPMC_CONFIG2: + - gpmc,cs-on: Assertion time + - gpmc,cs-rd-off: Read deassertion time + - gpmc,cs-wr-off: Write deassertion time + + ADV signal timings corresponding to GPMC_CONFIG3: + - gpmc,adv-on: Assertion time + - gpmc,adv-rd-off: Read deassertion time + - gpmc,adv-wr-off: Write deassertion time + + WE signals timings corresponding to GPMC_CONFIG4: + - gpmc,we-on: Assertion time + - gpmc,we-off: Deassertion time + + OE signals timings corresponding to GPMC_CONFIG4: + - gpmc,oe-on: Assertion time + - gpmc,oe-off: Deassertion time + + Access time and cycle time timings corresponding to GPMC_CONFIG5: + - gpmc,page-burst-access: Multiple access word delay + - gpmc,access: Start-cycle to first data valid delay + - gpmc,rd-cycle: Total read cycle time + - gpmc,wr-cycle: Total write cycle time + +The following are only applicable to OMAP3+ and AM335x: + - gpmc,wr-access + - gpmc,wr-data-mux-bus + + +Example for an AM33xx board: + + gpmc: gpmc@50000000 { + compatible = "ti,am3352-gpmc"; + ti,hwmods = "gpmc"; + reg = <0x50000000 0x2000>; + interrupts = <100>; + + gpmc,num-cs = <8>; + gpmc,num-waitpins = <2>; + #address-cells = <2>; + #size-cells = <1>; + ranges = <0 0 0x08000000 0x10000000>; /* CS0 @addr 0x8000000, size 0x10000000 */ + + /* child nodes go here */ + }; diff --git a/Documentation/devicetree/bindings/clock/imx31-clock.txt b/Documentation/devicetree/bindings/clock/imx31-clock.txt new file mode 100644 index 0000000..19df842c --- /dev/null +++ b/Documentation/devicetree/bindings/clock/imx31-clock.txt @@ -0,0 +1,91 @@ +* Clock bindings for Freescale i.MX31 + +Required properties: +- compatible: Should be "fsl,imx31-ccm" +- reg: Address and length of the register set +- interrupts: Should contain CCM interrupt +- #clock-cells: Should be <1> + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. The following is a full list of i.MX31 +clocks and IDs. + + Clock ID + ----------------------- + dummy 0 + ckih 1 + ckil 2 + mpll 3 + spll 4 + upll 5 + mcu_main 6 + hsp 7 + ahb 8 + nfc 9 + ipg 10 + per_div 11 + per 12 + csi_sel 13 + fir_sel 14 + csi_div 15 + usb_div_pre 16 + usb_div_post 17 + fir_div_pre 18 + fir_div_post 19 + sdhc1_gate 20 + sdhc2_gate 21 + gpt_gate 22 + epit1_gate 23 + epit2_gate 24 + iim_gate 25 + ata_gate 26 + sdma_gate 27 + cspi3_gate 28 + rng_gate 29 + uart1_gate 30 + uart2_gate 31 + ssi1_gate 32 + i2c1_gate 33 + i2c2_gate 34 + i2c3_gate 35 + hantro_gate 36 + mstick1_gate 37 + mstick2_gate 38 + csi_gate 39 + rtc_gate 40 + wdog_gate 41 + pwm_gate 42 + sim_gate 43 + ect_gate 44 + usb_gate 45 + kpp_gate 46 + ipu_gate 47 + uart3_gate 48 + uart4_gate 49 + uart5_gate 50 + owire_gate 51 + ssi2_gate 52 + cspi1_gate 53 + cspi2_gate 54 + gacc_gate 55 + emi_gate 56 + rtic_gate 57 + firi_gate 58 + +Examples: + +clks: ccm@53f80000{ + compatible = "fsl,imx31-ccm"; + reg = <0x53f80000 0x4000>; + interrupts = <0 31 0x04 0 53 0x04>; + #clock-cells = <1>; +}; + +uart1: serial@43f90000 { + compatible = "fsl,imx31-uart", "fsl,imx21-uart"; + reg = <0x43f90000 0x4000>; + interrupts = <45>; + clocks = <&clks 10>, <&clks 30>; + clock-names = "ipg", "per"; + status = "disabled"; +}; diff --git a/Documentation/devicetree/bindings/clock/imx5-clock.txt b/Documentation/devicetree/bindings/clock/imx5-clock.txt index 04ad478..2a0c904 100644 --- a/Documentation/devicetree/bindings/clock/imx5-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx5-clock.txt @@ -171,6 +171,7 @@ clocks and IDs. can_sel 156 can1_serial_gate 157 can1_ipg_gate 158 + owire_gate 159 Examples (for mx53): diff --git a/Documentation/devicetree/bindings/clock/imx6q-clock.txt b/Documentation/devicetree/bindings/clock/imx6q-clock.txt index f73fdf5..969b38e 100644 --- a/Documentation/devicetree/bindings/clock/imx6q-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx6q-clock.txt @@ -203,6 +203,8 @@ clocks and IDs. pcie_ref 188 pcie_ref_125m 189 enet_ref 190 + usbphy1_gate 191 + usbphy2_gate 192 Examples: diff --git a/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt b/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt index 7337005e..cffc93d 100644 --- a/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt +++ b/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt @@ -89,7 +89,7 @@ ID Clock Peripheral 16 xor1 XOR DMA 1 17 crypto CESA engine 18 pex1 PCIe Cntrl 1 -19 ge1 Gigabit Ethernet 0 +19 ge1 Gigabit Ethernet 1 20 tdm Time Division Mplx Required properties: diff --git a/Documentation/devicetree/bindings/clock/nvidia,tegra20-car.txt b/Documentation/devicetree/bindings/clock/nvidia,tegra20-car.txt new file mode 100644 index 0000000..0921fac --- /dev/null +++ b/Documentation/devicetree/bindings/clock/nvidia,tegra20-car.txt @@ -0,0 +1,205 @@ +NVIDIA Tegra20 Clock And Reset Controller + +This binding uses the common clock binding: +Documentation/devicetree/bindings/clock/clock-bindings.txt + +The CAR (Clock And Reset) Controller on Tegra is the HW module responsible +for muxing and gating Tegra's clocks, and setting their rates. + +Required properties : +- compatible : Should be "nvidia,tegra20-car" +- reg : Should contain CAR registers location and length +- clocks : Should contain phandle and clock specifiers for two clocks: + the 32 KHz "32k_in", and the board-specific oscillator "osc". +- #clock-cells : Should be 1. + In clock consumers, this cell represents the clock ID exposed by the CAR. + + The first 96 clocks are numbered to match the bits in the CAR's CLK_OUT_ENB + registers. These IDs often match those in the CAR's RST_DEVICES registers, + but not in all cases. Some bits in CLK_OUT_ENB affect multiple clocks. In + this case, those clocks are assigned IDs above 95 in order to highlight + this issue. Implementations that interpret these clock IDs as bit values + within the CLK_OUT_ENB or RST_DEVICES registers should be careful to + explicitly handle these special cases. + + The balance of the clocks controlled by the CAR are assigned IDs of 96 and + above. + + 0 cpu + 1 unassigned + 2 unassigned + 3 ac97 + 4 rtc + 5 tmr + 6 uart1 + 7 unassigned (register bit affects uart2 and vfir) + 8 gpio + 9 sdmmc2 + 10 unassigned (register bit affects spdif_in and spdif_out) + 11 i2s1 + 12 i2c1 + 13 ndflash + 14 sdmmc1 + 15 sdmmc4 + 16 twc + 17 pwm + 18 i2s2 + 19 epp + 20 unassigned (register bit affects vi and vi_sensor) + 21 2d + 22 usbd + 23 isp + 24 3d + 25 ide + 26 disp2 + 27 disp1 + 28 host1x + 29 vcp + 30 unassigned + 31 cache2 + + 32 mem + 33 ahbdma + 34 apbdma + 35 unassigned + 36 kbc + 37 stat_mon + 38 pmc + 39 fuse + 40 kfuse + 41 sbc1 + 42 snor + 43 spi1 + 44 sbc2 + 45 xio + 46 sbc3 + 47 dvc + 48 dsi + 49 unassigned (register bit affects tvo and cve) + 50 mipi + 51 hdmi + 52 csi + 53 tvdac + 54 i2c2 + 55 uart3 + 56 unassigned + 57 emc + 58 usb2 + 59 usb3 + 60 mpe + 61 vde + 62 bsea + 63 bsev + + 64 speedo + 65 uart4 + 66 uart5 + 67 i2c3 + 68 sbc4 + 69 sdmmc3 + 70 pcie + 71 owr + 72 afi + 73 csite + 74 unassigned + 75 avpucq + 76 la + 77 unassigned + 78 unassigned + 79 unassigned + 80 unassigned + 81 unassigned + 82 unassigned + 83 unassigned + 84 irama + 85 iramb + 86 iramc + 87 iramd + 88 cram2 + 89 audio_2x a/k/a audio_2x_sync_clk + 90 clk_d + 91 unassigned + 92 sus + 93 cdev1 + 94 cdev2 + 95 unassigned + + 96 uart2 + 97 vfir + 98 spdif_in + 99 spdif_out + 100 vi + 101 vi_sensor + 102 tvo + 103 cve + 104 osc + 105 clk_32k a/k/a clk_s + 106 clk_m + 107 sclk + 108 cclk + 109 hclk + 110 pclk + 111 blink + 112 pll_a + 113 pll_a_out0 + 114 pll_c + 115 pll_c_out1 + 116 pll_d + 117 pll_d_out0 + 118 pll_e + 119 pll_m + 120 pll_m_out1 + 121 pll_p + 122 pll_p_out1 + 123 pll_p_out2 + 124 pll_p_out3 + 125 pll_p_out4 + 126 pll_s + 127 pll_u + 128 pll_x + 129 cop a/k/a avp + 130 audio a/k/a audio_sync_clk + 131 pll_ref + 132 twd + +Example SoC include file: + +/ { + tegra_car: clock { + compatible = "nvidia,tegra20-car"; + reg = <0x60006000 0x1000>; + #clock-cells = <1>; + }; + + usb@c5004000 { + clocks = <&tegra_car 58>; /* usb2 */ + }; +}; + +Example board file: + +/ { + clocks { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + osc: clock@0 { + compatible = "fixed-clock"; + reg = <0>; + #clock-cells = <0>; + clock-frequency = <12000000>; + }; + + clk_32k: clock@1 { + compatible = "fixed-clock"; + reg = <1>; + #clock-cells = <0>; + clock-frequency = <32768>; + }; + }; + + &tegra_car { + clocks = <&clk_32k> <&osc>; + }; +}; diff --git a/Documentation/devicetree/bindings/clock/nvidia,tegra30-car.txt b/Documentation/devicetree/bindings/clock/nvidia,tegra30-car.txt new file mode 100644 index 0000000..f3da3be --- /dev/null +++ b/Documentation/devicetree/bindings/clock/nvidia,tegra30-car.txt @@ -0,0 +1,262 @@ +NVIDIA Tegra30 Clock And Reset Controller + +This binding uses the common clock binding: +Documentation/devicetree/bindings/clock/clock-bindings.txt + +The CAR (Clock And Reset) Controller on Tegra is the HW module responsible +for muxing and gating Tegra's clocks, and setting their rates. + +Required properties : +- compatible : Should be "nvidia,tegra30-car" +- reg : Should contain CAR registers location and length +- clocks : Should contain phandle and clock specifiers for two clocks: + the 32 KHz "32k_in", and the board-specific oscillator "osc". +- #clock-cells : Should be 1. + In clock consumers, this cell represents the clock ID exposed by the CAR. + + The first 130 clocks are numbered to match the bits in the CAR's CLK_OUT_ENB + registers. These IDs often match those in the CAR's RST_DEVICES registers, + but not in all cases. Some bits in CLK_OUT_ENB affect multiple clocks. In + this case, those clocks are assigned IDs above 160 in order to highlight + this issue. Implementations that interpret these clock IDs as bit values + within the CLK_OUT_ENB or RST_DEVICES registers should be careful to + explicitly handle these special cases. + + The balance of the clocks controlled by the CAR are assigned IDs of 160 and + above. + + 0 cpu + 1 unassigned + 2 unassigned + 3 unassigned + 4 rtc + 5 timer + 6 uarta + 7 unassigned (register bit affects uartb and vfir) + 8 gpio + 9 sdmmc2 + 10 unassigned (register bit affects spdif_in and spdif_out) + 11 i2s1 + 12 i2c1 + 13 ndflash + 14 sdmmc1 + 15 sdmmc4 + 16 unassigned + 17 pwm + 18 i2s2 + 19 epp + 20 unassigned (register bit affects vi and vi_sensor) + 21 2d + 22 usbd + 23 isp + 24 3d + 25 unassigned + 26 disp2 + 27 disp1 + 28 host1x + 29 vcp + 30 i2s0 + 31 cop_cache + + 32 mc + 33 ahbdma + 34 apbdma + 35 unassigned + 36 kbc + 37 statmon + 38 pmc + 39 unassigned (register bit affects fuse and fuse_burn) + 40 kfuse + 41 sbc1 + 42 nor + 43 unassigned + 44 sbc2 + 45 unassigned + 46 sbc3 + 47 i2c5 + 48 dsia + 49 unassigned (register bit affects cve and tvo) + 50 mipi + 51 hdmi + 52 csi + 53 tvdac + 54 i2c2 + 55 uartc + 56 unassigned + 57 emc + 58 usb2 + 59 usb3 + 60 mpe + 61 vde + 62 bsea + 63 bsev + + 64 speedo + 65 uartd + 66 uarte + 67 i2c3 + 68 sbc4 + 69 sdmmc3 + 70 pcie + 71 owr + 72 afi + 73 csite + 74 pciex + 75 avpucq + 76 la + 77 unassigned + 78 unassigned + 79 dtv + 80 ndspeed + 81 i2cslow + 82 dsib + 83 unassigned + 84 irama + 85 iramb + 86 iramc + 87 iramd + 88 cram2 + 89 unassigned + 90 audio_2x a/k/a audio_2x_sync_clk + 91 unassigned + 92 csus + 93 cdev2 + 94 cdev1 + 95 unassigned + + 96 cpu_g + 97 cpu_lp + 98 3d2 + 99 mselect + 100 tsensor + 101 i2s3 + 102 i2s4 + 103 i2c4 + 104 sbc5 + 105 sbc6 + 106 d_audio + 107 apbif + 108 dam0 + 109 dam1 + 110 dam2 + 111 hda2codec_2x + 112 atomics + 113 audio0_2x + 114 audio1_2x + 115 audio2_2x + 116 audio3_2x + 117 audio4_2x + 118 audio5_2x + 119 actmon + 120 extern1 + 121 extern2 + 122 extern3 + 123 sata_oob + 124 sata + 125 hda + 127 se + 128 hda2hdmi + 129 sata_cold + + 160 uartb + 161 vfir + 162 spdif_in + 163 spdif_out + 164 vi + 165 vi_sensor + 166 fuse + 167 fuse_burn + 168 cve + 169 tvo + + 170 clk_32k + 171 clk_m + 172 clk_m_div2 + 173 clk_m_div4 + 174 pll_ref + 175 pll_c + 176 pll_c_out1 + 177 pll_m + 178 pll_m_out1 + 179 pll_p + 180 pll_p_out1 + 181 pll_p_out2 + 182 pll_p_out3 + 183 pll_p_out4 + 184 pll_a + 185 pll_a_out0 + 186 pll_d + 187 pll_d_out0 + 188 pll_d2 + 189 pll_d2_out0 + 190 pll_u + 191 pll_x + 192 pll_x_out0 + 193 pll_e + 194 spdif_in_sync + 195 i2s0_sync + 196 i2s1_sync + 197 i2s2_sync + 198 i2s3_sync + 199 i2s4_sync + 200 vimclk + 201 audio0 + 202 audio1 + 203 audio2 + 204 audio3 + 205 audio4 + 206 audio5 + 207 clk_out_1 (extern1) + 208 clk_out_2 (extern2) + 209 clk_out_3 (extern3) + 210 sclk + 211 blink + 212 cclk_g + 213 cclk_lp + 214 twd + 215 cml0 + 216 cml1 + 217 hclk + 218 pclk + +Example SoC include file: + +/ { + tegra_car: clock { + compatible = "nvidia,tegra30-car"; + reg = <0x60006000 0x1000>; + #clock-cells = <1>; + }; + + usb@c5004000 { + clocks = <&tegra_car 58>; /* usb2 */ + }; +}; + +Example board file: + +/ { + clocks { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + osc: clock@0 { + compatible = "fixed-clock"; + reg = <0>; + #clock-cells = <0>; + clock-frequency = <12000000>; + }; + + clk_32k: clock@1 { + compatible = "fixed-clock"; + reg = <1>; + #clock-cells = <0>; + clock-frequency = <32768>; + }; + }; + + &tegra_car { + clocks = <&clk_32k> <&osc>; + }; +}; diff --git a/Documentation/devicetree/bindings/clock/prima2-clock.txt b/Documentation/devicetree/bindings/clock/prima2-clock.txt new file mode 100644 index 0000000..5016979 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/prima2-clock.txt @@ -0,0 +1,73 @@ +* Clock bindings for CSR SiRFprimaII + +Required properties: +- compatible: Should be "sirf,prima2-clkc" +- reg: Address and length of the register set +- interrupts: Should contain clock controller interrupt +- #clock-cells: Should be <1> + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. The following is a full list of prima2 +clocks and IDs. + + Clock ID + --------------------------- + rtc 0 + osc 1 + pll1 2 + pll2 3 + pll3 4 + mem 5 + sys 6 + security 7 + dsp 8 + gps 9 + mf 10 + io 11 + cpu 12 + uart0 13 + uart1 14 + uart2 15 + tsc 16 + i2c0 17 + i2c1 18 + spi0 19 + spi1 20 + pwmc 21 + efuse 22 + pulse 23 + dmac0 24 + dmac1 25 + nand 26 + audio 27 + usp0 28 + usp1 29 + usp2 30 + vip 31 + gfx 32 + mm 33 + lcd 34 + vpp 35 + mmc01 36 + mmc23 37 + mmc45 38 + usbpll 39 + usb0 40 + usb1 41 + +Examples: + +clks: clock-controller@88000000 { + compatible = "sirf,prima2-clkc"; + reg = <0x88000000 0x1000>; + interrupts = <3>; + #clock-cells = <1>; +}; + +i2c0: i2c@b00e0000 { + cell-index = <0>; + compatible = "sirf,prima2-i2c"; + reg = <0xb00e0000 0x10000>; + interrupts = <24>; + clocks = <&clks 17>; +}; diff --git a/Documentation/devicetree/bindings/crypto/fsl-sec4.txt b/Documentation/devicetree/bindings/crypto/fsl-sec4.txt index fc9ce6f..e402277 100644 --- a/Documentation/devicetree/bindings/crypto/fsl-sec4.txt +++ b/Documentation/devicetree/bindings/crypto/fsl-sec4.txt @@ -54,8 +54,13 @@ PROPERTIES - compatible Usage: required Value type: <string> - Definition: Must include "fsl,sec-v4.0". Also includes SEC - ERA versions (optional) with which the device is compatible. + Definition: Must include "fsl,sec-v4.0" + + - fsl,sec-era + Usage: optional + Value type: <u32> + Definition: A standard property. Define the 'ERA' of the SEC + device. - #address-cells Usage: required @@ -107,7 +112,8 @@ PROPERTIES EXAMPLE crypto@300000 { - compatible = "fsl,sec-v4.0", "fsl,sec-era-v2.0"; + compatible = "fsl,sec-v4.0"; + fsl,sec-era = <2>; #address-cells = <1>; #size-cells = <1>; reg = <0x300000 0x10000>; diff --git a/Documentation/devicetree/bindings/dma/arm-pl330.txt b/Documentation/devicetree/bindings/dma/arm-pl330.txt index 36e27d5..2675658 100644 --- a/Documentation/devicetree/bindings/dma/arm-pl330.txt +++ b/Documentation/devicetree/bindings/dma/arm-pl330.txt @@ -10,7 +10,11 @@ Required properties: - interrupts: interrupt number to the cpu. Optional properties: -- dma-coherent : Present if dma operations are coherent + - dma-coherent : Present if dma operations are coherent + - #dma-cells: must be <1>. used to represent the number of integer + cells in the dmas property of client device. + - dma-channels: contains the total number of DMA channels supported by the DMAC + - dma-requests: contains the total number of DMA requests supported by the DMAC Example: @@ -18,16 +22,23 @@ Example: compatible = "arm,pl330", "arm,primecell"; reg = <0x12680000 0x1000>; interrupts = <99>; + #dma-cells = <1>; + #dma-channels = <8>; + #dma-requests = <32>; }; Client drivers (device nodes requiring dma transfers from dev-to-mem or -mem-to-dev) should specify the DMA channel numbers using a two-value pair +mem-to-dev) should specify the DMA channel numbers and dma channel names as shown below. [property name] = <[phandle of the dma controller] [dma request id]>; + [property name] = <[dma channel name]> where 'dma request id' is the dma request number which is connected - to the client controller. The 'property name' is recommended to be - of the form <name>-dma-channel. + to the client controller. The 'property name' 'dmas' and 'dma-names' + as required by the generic dma device tree binding helpers. The dma + names correspond 1:1 with the dma request ids in the dmas property. - Example: tx-dma-channel = <&pdma0 12>; + Example: dmas = <&pdma0 12 + &pdma1 11>; + dma-names = "tx", "rx"; diff --git a/Documentation/devicetree/bindings/dma/dma.txt b/Documentation/devicetree/bindings/dma/dma.txt new file mode 100644 index 0000000..8f504e6 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/dma.txt @@ -0,0 +1,81 @@ +* Generic DMA Controller and DMA request bindings + +Generic binding to provide a way for a driver using DMA Engine to retrieve the +DMA request or channel information that goes from a hardware device to a DMA +controller. + + +* DMA controller + +Required property: +- #dma-cells: Must be at least 1. Used to provide DMA controller + specific information. See DMA client binding below for + more details. + +Optional properties: +- dma-channels: Number of DMA channels supported by the controller. +- dma-requests: Number of DMA requests signals supported by the + controller. + +Example: + + dma: dma@48000000 { + compatible = "ti,omap-sdma"; + reg = <0x48000000 0x1000>; + interrupts = <0 12 0x4 + 0 13 0x4 + 0 14 0x4 + 0 15 0x4>; + #dma-cells = <1>; + dma-channels = <32>; + dma-requests = <127>; + }; + + +* DMA client + +Client drivers should specify the DMA property using a phandle to the controller +followed by DMA controller specific data. + +Required property: +- dmas: List of one or more DMA specifiers, each consisting of + - A phandle pointing to DMA controller node + - A number of integer cells, as determined by the + #dma-cells property in the node referenced by phandle + containing DMA controller specific information. This + typically contains a DMA request line number or a + channel number, but can contain any data that is used + required for configuring a channel. +- dma-names: Contains one identifier string for each DMA specifier in + the dmas property. The specific strings that can be used + are defined in the binding of the DMA client device. + Multiple DMA specifiers can be used to represent + alternatives and in this case the dma-names for those + DMA specifiers must be identical (see examples). + +Examples: + +1. A device with one DMA read channel, one DMA write channel: + + i2c1: i2c@1 { + ... + dmas = <&dma 2 /* read channel */ + &dma 3>; /* write channel */ + dma-names = "rx", "tx"; + ... + }; + +2. A single read-write channel with three alternative DMA controllers: + + dmas = <&dma1 5 + &dma2 7 + &dma3 2>; + dma-names = "rx-tx", "rx-tx", "rx-tx"; + +3. A device with three channels, one of which has two alternatives: + + dmas = <&dma1 2 /* read channel */ + &dma1 3 /* write channel */ + &dma2 0 /* error read */ + &dma3 0>; /* alternative error read */ + dma-names = "rx", "tx", "error", "error"; diff --git a/Documentation/devicetree/bindings/dma/snps-dma.txt b/Documentation/devicetree/bindings/dma/snps-dma.txt index c0d85db..d58675e 100644 --- a/Documentation/devicetree/bindings/dma/snps-dma.txt +++ b/Documentation/devicetree/bindings/dma/snps-dma.txt @@ -3,15 +3,61 @@ Required properties: - compatible: "snps,dma-spear1340" - reg: Address range of the DMAC registers +- interrupt: Should contain the DMAC interrupt number +- dma-channels: Number of channels supported by hardware +- dma-requests: Number of DMA request lines supported, up to 16 +- dma-masters: Number of AHB masters supported by the controller +- #dma-cells: must be <3> +- chan_allocation_order: order of allocation of channel, 0 (default): ascending, + 1: descending +- chan_priority: priority of channels. 0 (default): increase from chan 0->n, 1: + increase from chan n->0 +- block_size: Maximum block size supported by the controller +- data_width: Maximum data width supported by hardware per AHB master + (0 - 8bits, 1 - 16bits, ..., 5 - 256bits) + + +Optional properties: - interrupt-parent: Should be the phandle for the interrupt controller that services interrupts for this device -- interrupt: Should contain the DMAC interrupt number +- is_private: The device channels should be marked as private and not for by the + general purpose DMA channel allocator. False if not passed. Example: - dma@fc000000 { + dmahost: dma@fc000000 { compatible = "snps,dma-spear1340"; reg = <0xfc000000 0x1000>; interrupt-parent = <&vic1>; interrupts = <12>; + + dma-channels = <8>; + dma-requests = <16>; + dma-masters = <2>; + #dma-cells = <3>; + chan_allocation_order = <1>; + chan_priority = <1>; + block_size = <0xfff>; + data_width = <3 3 0 0>; + }; + +DMA clients connected to the Designware DMA controller must use the format +described in the dma.txt file, using a four-cell specifier for each channel. +The four cells in order are: + +1. A phandle pointing to the DMA controller +2. The DMA request line number +3. Source master for transfers on allocated channel +4. Destination master for transfers on allocated channel + +Example: + + serial@e0000000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0xe0000000 0x1000>; + interrupts = <0 35 0x4>; + status = "disabled"; + dmas = <&dmahost 12 0 1>, + <&dmahost 13 0 1 0>; + dma-names = "rx", "rx"; }; diff --git a/Documentation/devicetree/bindings/drm/exynos/g2d.txt b/Documentation/devicetree/bindings/drm/exynos/g2d.txt new file mode 100644 index 0000000..1eb124d --- /dev/null +++ b/Documentation/devicetree/bindings/drm/exynos/g2d.txt @@ -0,0 +1,22 @@ +Samsung 2D Graphic Accelerator using DRM frame work + +Samsung FIMG2D is a graphics 2D accelerator which supports Bit Block Transfer. +We set the drawing-context registers for configuring rendering parameters and +then start rendering. +This driver is for SOCs which contain G2D IPs with version 4.1. + +Required properties: + -compatible: + should be "samsung,exynos-g2d-41". + -reg: + physical base address of the controller and length + of memory mapped region. + -interrupts: + interrupt combiner values. + +Example: + g2d { + compatible = "samsung,exynos-g2d-41"; + reg = <0x10850000 0x1000>; + interrupts = <0 91 0>; + }; diff --git a/Documentation/devicetree/bindings/drm/tilcdc/panel.txt b/Documentation/devicetree/bindings/drm/tilcdc/panel.txt new file mode 100644 index 0000000..9301c33 --- /dev/null +++ b/Documentation/devicetree/bindings/drm/tilcdc/panel.txt @@ -0,0 +1,59 @@ +Device-Tree bindings for tilcdc DRM generic panel output driver + +Required properties: + - compatible: value should be "ti,tilcdc,panel". + - panel-info: configuration info to configure LCDC correctly for the panel + - ac-bias: AC Bias Pin Frequency + - ac-bias-intrpt: AC Bias Pin Transitions per Interrupt + - dma-burst-sz: DMA burst size + - bpp: Bits per pixel + - fdd: FIFO DMA Request Delay + - sync-edge: Horizontal and Vertical Sync Edge: 0=rising 1=falling + - sync-ctrl: Horizontal and Vertical Sync: Control: 0=ignore + - raster-order: Raster Data Order Select: 1=Most-to-least 0=Least-to-most + - fifo-th: DMA FIFO threshold + - display-timings: typical videomode of lcd panel. Multiple video modes + can be listed if the panel supports multiple timings, but the 'native-mode' + should be the preferred/default resolution. Refer to + Documentation/devicetree/bindings/video/display-timing.txt for display + timing binding details. + +Recommended properties: + - pinctrl-names, pinctrl-0: the pincontrol settings to configure + muxing properly for pins that connect to TFP410 device + +Example: + + /* Settings for CDTech_S035Q01 / LCD3 cape: */ + lcd3 { + compatible = "ti,tilcdc,panel"; + pinctrl-names = "default"; + pinctrl-0 = <&bone_lcd3_cape_lcd_pins>; + panel-info { + ac-bias = <255>; + ac-bias-intrpt = <0>; + dma-burst-sz = <16>; + bpp = <16>; + fdd = <0x80>; + sync-edge = <0>; + sync-ctrl = <1>; + raster-order = <0>; + fifo-th = <0>; + }; + display-timings { + native-mode = <&timing0>; + timing0: 320x240 { + hactive = <320>; + vactive = <240>; + hback-porch = <21>; + hfront-porch = <58>; + hsync-len = <47>; + vback-porch = <11>; + vfront-porch = <23>; + vsync-len = <2>; + clock-frequency = <8000000>; + hsync-active = <0>; + vsync-active = <0>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/drm/tilcdc/slave.txt b/Documentation/devicetree/bindings/drm/tilcdc/slave.txt new file mode 100644 index 0000000..3d2c524 --- /dev/null +++ b/Documentation/devicetree/bindings/drm/tilcdc/slave.txt @@ -0,0 +1,18 @@ +Device-Tree bindings for tilcdc DRM encoder slave output driver + +Required properties: + - compatible: value should be "ti,tilcdc,slave". + - i2c: the phandle for the i2c device the encoder slave is connected to + +Recommended properties: + - pinctrl-names, pinctrl-0: the pincontrol settings to configure + muxing properly for pins that connect to TFP410 device + +Example: + + hdmi { + compatible = "ti,tilcdc,slave"; + i2c = <&i2c0>; + pinctrl-names = "default"; + pinctrl-0 = <&nxp_hdmi_bonelt_pins>; + }; diff --git a/Documentation/devicetree/bindings/drm/tilcdc/tfp410.txt b/Documentation/devicetree/bindings/drm/tilcdc/tfp410.txt new file mode 100644 index 0000000..a58ae77 --- /dev/null +++ b/Documentation/devicetree/bindings/drm/tilcdc/tfp410.txt @@ -0,0 +1,21 @@ +Device-Tree bindings for tilcdc DRM TFP410 output driver + +Required properties: + - compatible: value should be "ti,tilcdc,tfp410". + - i2c: the phandle for the i2c device to use for DDC + +Recommended properties: + - pinctrl-names, pinctrl-0: the pincontrol settings to configure + muxing properly for pins that connect to TFP410 device + - powerdn-gpio: the powerdown GPIO, pulled low to power down the + TFP410 device (for DPMS_OFF) + +Example: + + dvicape { + compatible = "ti,tilcdc,tfp410"; + i2c = <&i2c2>; + pinctrl-names = "default"; + pinctrl-0 = <&bone_dvi_cape_dvi_00A1_pins>; + powerdn-gpio = <&gpio2 31 0>; + }; diff --git a/Documentation/devicetree/bindings/drm/tilcdc/tilcdc.txt b/Documentation/devicetree/bindings/drm/tilcdc/tilcdc.txt new file mode 100644 index 0000000..e5f1301 --- /dev/null +++ b/Documentation/devicetree/bindings/drm/tilcdc/tilcdc.txt @@ -0,0 +1,21 @@ +Device-Tree bindings for tilcdc DRM driver + +Required properties: + - compatible: value should be "ti,am33xx-tilcdc". + - interrupts: the interrupt number + - reg: base address and size of the LCDC device + +Recommended properties: + - interrupt-parent: the phandle for the interrupt controller that + services interrupts for this device. + - ti,hwmods: Name of the hwmod associated to the LCDC + +Example: + + fb: fb@4830e000 { + compatible = "ti,am33xx-tilcdc"; + reg = <0x4830e000 0x1000>; + interrupt-parent = <&intc>; + interrupts = <36>; + ti,hwmods = "lcdc"; + }; diff --git a/Documentation/devicetree/bindings/i2c/brcm,bcm2835-i2c.txt b/Documentation/devicetree/bindings/i2c/brcm,bcm2835-i2c.txt new file mode 100644 index 0000000..e9de375 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/brcm,bcm2835-i2c.txt @@ -0,0 +1,20 @@ +Broadcom BCM2835 I2C controller + +Required properties: +- compatible : Should be "brcm,bcm2835-i2c". +- reg: Should contain register location and length. +- interrupts: Should contain interrupt. +- clocks : The clock feeding the I2C controller. + +Recommended properties: +- clock-frequency : desired I2C bus clock frequency in Hz. + +Example: + +i2c@20205000 { + compatible = "brcm,bcm2835-i2c"; + reg = <0x7e205000 0x1000>; + interrupts = <2 21>; + clocks = <&clk_i2c>; + clock-frequency = <100000>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt b/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt index e9611ac..f98d4c5 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt @@ -8,6 +8,8 @@ Required properties: (b) "samsung, s3c2440-i2c", for i2c compatible with s3c2440 i2c. (c) "samsung, s3c2440-hdmiphy-i2c", for s3c2440-like i2c used inside HDMIPHY block found on several samsung SoCs + (d) "samsung, exynos5440-i2c", for s3c2440-like i2c used + on EXYNOS5440 which does not need GPIO configuration. - reg: physical base address of the controller and length of memory mapped region. - interrupts: interrupt number to the cpu. diff --git a/Documentation/devicetree/bindings/i2c/ina209.txt b/Documentation/devicetree/bindings/i2c/ina209.txt new file mode 100644 index 0000000..9dd2bee --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/ina209.txt @@ -0,0 +1,18 @@ +ina209 properties + +Required properties: +- compatible: Must be "ti,ina209" +- reg: I2C address + +Optional properties: + +- shunt-resistor + Shunt resistor value in micro-Ohm + +Example: + +temp-sensor@4c { + compatible = "ti,ina209"; + reg = <0x4c>; + shunt-resistor = <5000>; +}; diff --git a/Documentation/devicetree/bindings/i2c/max6697.txt b/Documentation/devicetree/bindings/i2c/max6697.txt new file mode 100644 index 0000000..5f79399 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/max6697.txt @@ -0,0 +1,64 @@ +max6697 properties + +Required properties: +- compatible: + Should be one of + maxim,max6581 + maxim,max6602 + maxim,max6622 + maxim,max6636 + maxim,max6689 + maxim,max6693 + maxim,max6694 + maxim,max6697 + maxim,max6698 + maxim,max6699 +- reg: I2C address + +Optional properties: + +- smbus-timeout-disable + Set to disable SMBus timeout. If not specified, SMBus timeout will be + enabled. +- extended-range-enable + Only valid for MAX6581. Set to enable extended temperature range. + Extended temperature will be disabled if not specified. +- beta-compensation-enable + Only valid for MAX6693 and MX6694. Set to enable beta compensation on + remote temperature channel 1. + Beta compensation will be disabled if not specified. +- alert-mask + Alert bit mask. Alert disabled for bits set. + Select bit 0 for local temperature, bit 1..7 for remote temperatures. + If not specified, alert will be enabled for all channels. +- over-temperature-mask + Over-temperature bit mask. Over-temperature reporting disabled for + bits set. + Select bit 0 for local temperature, bit 1..7 for remote temperatures. + If not specified, over-temperature reporting will be enabled for all + channels. +- resistance-cancellation + Boolean for all chips other than MAX6581. Set to enable resistance + cancellation on remote temperature channel 1. + For MAX6581, resistance cancellation enabled for all channels if + specified as boolean, otherwise as per bit mask specified. + Only supported for remote temperatures (bit 1..7). + If not specified, resistance cancellation will be disabled for all + channels. +- transistor-ideality + For MAX6581 only. Two values; first is bit mask, second is ideality + select value as per MAX6581 data sheet. Select bit 1..7 for remote + channels. + Transistor ideality will be initialized to default (1.008) if not + specified. + +Example: + +temp-sensor@1a { + compatible = "maxim,max6697"; + reg = <0x1a>; + smbus-timeout-disable; + resistance-cancellation; + alert-mask = <0x72>; + over-temperature-mask = <0x7f>; +}; diff --git a/Documentation/devicetree/bindings/input/imx-keypad.txt b/Documentation/devicetree/bindings/input/imx-keypad.txt new file mode 100644 index 0000000..2ebaf7d --- /dev/null +++ b/Documentation/devicetree/bindings/input/imx-keypad.txt @@ -0,0 +1,53 @@ +* Freescale i.MX Keypad Port(KPP) device tree bindings + +The KPP is designed to interface with a keypad matrix with 2-point contact +or 3-point contact keys. The KPP is designed to simplify the software task +of scanning a keypad matrix. The KPP is capable of detecting, debouncing, +and decoding one or multiple keys pressed simultaneously on a keypad. + +Required SoC Specific Properties: +- compatible: Should be "fsl,<soc>-kpp". + +- reg: Physical base address of the KPP and length of memory mapped + region. + +- interrupts: The KPP interrupt number to the CPU(s). + +- clocks: The clock provided by the SoC to the KPP. Some SoCs use dummy +clock(The clock for the KPP is provided by the SoCs automatically). + +Required Board Specific Properties: +- pinctrl-names: The definition can be found at +pinctrl/pinctrl-bindings.txt. + +- pinctrl-0: The definition can be found at +pinctrl/pinctrl-bindings.txt. + +- linux,keymap: The definition can be found at +bindings/input/matrix-keymap.txt. + +Example: +kpp: kpp@73f94000 { + compatible = "fsl,imx51-kpp", "fsl,imx21-kpp"; + reg = <0x73f94000 0x4000>; + interrupts = <60>; + clocks = <&clks 0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_kpp_1>; + linux,keymap = <0x00000067 /* KEY_UP */ + 0x0001006c /* KEY_DOWN */ + 0x00020072 /* KEY_VOLUMEDOWN */ + 0x00030066 /* KEY_HOME */ + 0x0100006a /* KEY_RIGHT */ + 0x01010069 /* KEY_LEFT */ + 0x0102001c /* KEY_ENTER */ + 0x01030073 /* KEY_VOLUMEUP */ + 0x02000040 /* KEY_F6 */ + 0x02010042 /* KEY_F8 */ + 0x02020043 /* KEY_F9 */ + 0x02030044 /* KEY_F10 */ + 0x0300003b /* KEY_F1 */ + 0x0301003c /* KEY_F2 */ + 0x0302003d /* KEY_F3 */ + 0x03030074>; /* KEY_POWER */ +}; diff --git a/Documentation/devicetree/bindings/input/lpc32xx-key.txt b/Documentation/devicetree/bindings/input/lpc32xx-key.txt index 31afd50..bcf62f8 100644 --- a/Documentation/devicetree/bindings/input/lpc32xx-key.txt +++ b/Documentation/devicetree/bindings/input/lpc32xx-key.txt @@ -1,19 +1,22 @@ NXP LPC32xx Key Scan Interface +This binding is based on the matrix-keymap binding with the following +changes: + Required Properties: - compatible: Should be "nxp,lpc3220-key" - reg: Physical base address of the controller and length of memory mapped region. - interrupts: The interrupt number to the cpu. -- keypad,num-rows: Number of rows and columns, e.g. 1: 1x1, 6: 6x6 -- keypad,num-columns: Must be equal to keypad,num-rows since LPC32xx only - supports square matrices - nxp,debounce-delay-ms: Debounce delay in ms - nxp,scan-delay-ms: Repeated scan period in ms - linux,keymap: the key-code to be reported when the key is pressed and released, see also Documentation/devicetree/bindings/input/matrix-keymap.txt +Note: keypad,num-rows and keypad,num-columns are required, and must be equal +since LPC32xx only supports square matrices + Example: key@40050000 { diff --git a/Documentation/devicetree/bindings/input/matrix-keymap.txt b/Documentation/devicetree/bindings/input/matrix-keymap.txt index 3cd8b98..c54919f 100644 --- a/Documentation/devicetree/bindings/input/matrix-keymap.txt +++ b/Documentation/devicetree/bindings/input/matrix-keymap.txt @@ -9,6 +9,12 @@ Required properties: row << 24 | column << 16 | key-code Optional properties: +Properties for the number of rows and columns are optional because some +drivers will use fixed values for these. +- keypad,num-rows: Number of row lines connected to the keypad controller. +- keypad,num-columns: Number of column lines connected to the keypad + controller. + Some users of this binding might choose to specify secondary keymaps for cases where there is a modifier key such as a Fn key. Proposed names for said properties are "linux,fn-keymap" or with another descriptive @@ -17,3 +23,5 @@ word for the modifier other from "Fn". Example: linux,keymap = < 0x00030012 0x0102003a >; + keypad,num-rows = <2>; + keypad,num-columns = <8>; diff --git a/Documentation/devicetree/bindings/input/nvidia,tegra20-kbc.txt b/Documentation/devicetree/bindings/input/nvidia,tegra20-kbc.txt index 72683be..2995fae 100644 --- a/Documentation/devicetree/bindings/input/nvidia,tegra20-kbc.txt +++ b/Documentation/devicetree/bindings/input/nvidia,tegra20-kbc.txt @@ -1,7 +1,18 @@ * Tegra keyboard controller +The key controller has maximum 24 pins to make matrix keypad. Any pin +can be configured as row or column. The maximum column pin can be 8 +and maximum row pins can be 16 for Tegra20/Tegra30. Required properties: - compatible: "nvidia,tegra20-kbc" +- reg: Register base address of KBC. +- interrupts: Interrupt number for the KBC. +- nvidia,kbc-row-pins: The KBC pins which are configured as row. This is an + array of pin numbers which is used as rows. +- nvidia,kbc-col-pins: The KBC pins which are configured as column. This is an + array of pin numbers which is used as column. +- linux,keymap: The keymap for keys as described in the binding document + devicetree/bindings/input/matrix-keymap.txt. Optional properties, in addition to those specified by the shared matrix-keyboard bindings: @@ -19,5 +30,16 @@ Example: keyboard: keyboard { compatible = "nvidia,tegra20-kbc"; reg = <0x7000e200 0x100>; + interrupts = <0 85 0x04>; nvidia,ghost-filter; + nvidia,debounce-delay-ms = <640>; + nvidia,kbc-row-pins = <0 1 2>; /* pin 0, 1, 2 as rows */ + nvidia,kbc-col-pins = <11 12 13>; /* pin 11, 12, 13 as columns */ + linux,keymap = <0x00000074 + 0x00010067 + 0x00020066 + 0x01010068 + 0x02000069 + 0x02010070 + 0x02020071>; }; diff --git a/Documentation/devicetree/bindings/input/omap-keypad.txt b/Documentation/devicetree/bindings/input/omap-keypad.txt index f2fa5e1..34ed1c6 100644 --- a/Documentation/devicetree/bindings/input/omap-keypad.txt +++ b/Documentation/devicetree/bindings/input/omap-keypad.txt @@ -6,19 +6,16 @@ A key can be placed at each intersection of a unique row and a unique column. The keypad controller can sense a key-press and key-release and report the event using a interrupt to the cpu. +This binding is based on the matrix-keymap binding with the following +changes: + +keypad,num-rows and keypad,num-columns are required. + Required SoC Specific Properties: - compatible: should be one of the following - "ti,omap4-keypad": For controllers compatible with omap4 keypad controller. -Required Board Specific Properties, in addition to those specified by -the shared matrix-keyboard bindings: -- keypad,num-rows: Number of row lines connected to the keypad - controller. - -- keypad,num-columns: Number of column lines connected to the - keypad controller. - Optional Properties specific to linux: - linux,keypad-no-autorepeat: do no enable autorepeat feature. diff --git a/Documentation/devicetree/bindings/input/tca8418_keypad.txt b/Documentation/devicetree/bindings/input/tca8418_keypad.txt index 2a1538f..2551850 100644 --- a/Documentation/devicetree/bindings/input/tca8418_keypad.txt +++ b/Documentation/devicetree/bindings/input/tca8418_keypad.txt @@ -1,8 +1,10 @@ +This binding is based on the matrix-keymap binding with the following +changes: + +keypad,num-rows and keypad,num-columns are required. Required properties: - compatible: "ti,tca8418" - reg: the I2C address - interrupts: IRQ line number, should trigger on falling edge -- keypad,num-rows: The number of rows -- keypad,num-columns: The number of columns - linux,keymap: Keys definitions, see keypad-matrix. diff --git a/Documentation/devicetree/bindings/gpio/leds-ns2.txt b/Documentation/devicetree/bindings/leds/leds-ns2.txt index aef3aca..aef3aca 100644 --- a/Documentation/devicetree/bindings/gpio/leds-ns2.txt +++ b/Documentation/devicetree/bindings/leds/leds-ns2.txt diff --git a/Documentation/devicetree/bindings/leds/leds-pwm.txt b/Documentation/devicetree/bindings/leds/leds-pwm.txt new file mode 100644 index 0000000..7297107 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-pwm.txt @@ -0,0 +1,48 @@ +LED connected to PWM + +Required properties: +- compatible : should be "pwm-leds". + +Each LED is represented as a sub-node of the pwm-leds device. Each +node's name represents the name of the corresponding LED. + +LED sub-node properties: +- pwms : PWM property to point to the PWM device (phandle)/port (id) and to + specify the period time to be used: <&phandle id period_ns>; +- pwm-names : (optional) Name to be used by the PWM subsystem for the PWM device + For the pwms and pwm-names property please refer to: + Documentation/devicetree/bindings/pwm/pwm.txt +- max-brightness : Maximum brightness possible for the LED +- label : (optional) + see Documentation/devicetree/bindings/leds/common.txt +- linux,default-trigger : (optional) + see Documentation/devicetree/bindings/leds/common.txt + +Example: + +twl_pwm: pwm { + /* provides two PWMs (id 0, 1 for PWM1 and PWM2) */ + compatible = "ti,twl6030-pwm"; + #pwm-cells = <2>; +}; + +twl_pwmled: pwmled { + /* provides one PWM (id 0 for Charing indicator LED) */ + compatible = "ti,twl6030-pwmled"; + #pwm-cells = <2>; +}; + +pwmleds { + compatible = "pwm-leds"; + kpad { + label = "omap4::keypad"; + pwms = <&twl_pwm 0 7812500>; + max-brightness = <127>; + }; + + charging { + label = "omap4:green:chrg"; + pwms = <&twl_pwmled 0 7812500>; + max-brightness = <255>; + }; +}; diff --git a/Documentation/devicetree/bindings/leds/tca6507.txt b/Documentation/devicetree/bindings/leds/tca6507.txt new file mode 100644 index 0000000..2b6693b --- /dev/null +++ b/Documentation/devicetree/bindings/leds/tca6507.txt @@ -0,0 +1,33 @@ +LEDs conected to tca6507 + +Required properties: +- compatible : should be : "ti,tca6507". + +Each led is represented as a sub-node of the ti,tca6507 device. + +LED sub-node properties: +- label : (optional) see Documentation/devicetree/bindings/leds/common.txt +- reg : number of LED line (could be from 0 to 6) +- linux,default-trigger : (optional) + see Documentation/devicetree/bindings/leds/common.txt + +Examples: + +tca6507@45 { + compatible = "ti,tca6507"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x45>; + + led0: red-aux@0 { + label = "red:aux"; + reg = <0x0>; + }; + + led1: green-aux@1 { + label = "green:aux"; + reg = <0x5>; + linux,default-trigger = "default-on"; + }; +}; + diff --git a/Documentation/devicetree/bindings/media/gpio-ir-receiver.txt b/Documentation/devicetree/bindings/media/gpio-ir-receiver.txt new file mode 100644 index 0000000..56e726e --- /dev/null +++ b/Documentation/devicetree/bindings/media/gpio-ir-receiver.txt @@ -0,0 +1,16 @@ +Device-Tree bindings for GPIO IR receiver + +Required properties: + - compatible: should be "gpio-ir-receiver". + - gpios: specifies GPIO used for IR signal reception. + +Optional properties: + - linux,rc-map-name: Linux specific remote control map name. + +Example node: + + ir: ir-receiver { + compatible = "gpio-ir-receiver"; + gpios = <&gpio0 19 1>; + linux,rc-map-name = "rc-rc6-mce"; + }; diff --git a/Documentation/devicetree/bindings/mfd/max8925.txt b/Documentation/devicetree/bindings/mfd/max8925.txt new file mode 100644 index 0000000..4f0dc66 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/max8925.txt @@ -0,0 +1,64 @@ +* Maxim max8925 Power Management IC + +Required parent device properties: +- compatible : "maxim,max8925" +- reg : the I2C slave address for the max8925 chip +- interrupts : IRQ line for the max8925 chip +- interrupt-controller: describes the max8925 as an interrupt + controller (has its own domain) +- #interrupt-cells : should be 1. + - The cell is the max8925 local IRQ number + +Optional parent device properties: +- maxim,tsc-irq: there are 2 IRQ lines for max8925, one is indicated in + interrupts property, the other is indicated here. + +max8925 consists of a large and varied group of sub-devices: + +Device Supply Names Description +------ ------------ ----------- +max8925-onkey : : On key +max8925-rtc : : RTC +max8925-regulator : : Regulators +max8925-backlight : : Backlight +max8925-touch : : Touchscreen +max8925-power : : Charger + +Example: + + pmic: max8925@3c { + compatible = "maxim,max8925"; + reg = <0x3c>; + interrupts = <1>; + interrupt-parent = <&intcmux4>; + interrupt-controller; + #interrupt-cells = <1>; + maxim,tsc-irq = <0>; + + regulators { + SDV1 { + regulator-min-microvolt = <637500>; + regulator-max-microvolt = <1425000>; + regulator-boot-on; + regulator-always-on; + }; + + LDO1 { + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <3900000>; + regulator-boot-on; + regulator-always-on; + }; + + }; + backlight { + maxim,max8925-dual-string = <0>; + }; + charger { + batt-detect = <0>; + topoff-threshold = <1>; + fast-charge = <7>; + no-temp-support = <0>; + no-insert-detect = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/tps6507x.txt b/Documentation/devicetree/bindings/mfd/tps6507x.txt new file mode 100755 index 0000000..8fffa3c --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/tps6507x.txt @@ -0,0 +1,91 @@ +TPS6507x Power Management Integrated Circuit + +Required properties: +- compatible: "ti,tps6507x" +- reg: I2C slave address +- regulators: This is the list of child nodes that specify the regulator + initialization data for defined regulators. Not all regulators for the + given device need to be present. The definition for each of these nodes + is defined using the standard binding for regulators found at + Documentation/devicetree/bindings/regulator/regulator.txt. + The regulator is matched with the regulator-compatible. + + The valid regulator-compatible values are: + tps6507x: vdcdc1, vdcdc2, vdcdc3, vldo1, vldo2 +- xxx-supply: Input voltage supply regulator. + These entries are required if regulators are enabled for a device. + Missing of these properties can cause the regulator registration + fails. + If some of input supply is powered through battery or always-on + supply then also it is require to have these parameters with proper + node handle of always on power supply. + tps6507x: + vindcdc1_2-supply: VDCDC1 and VDCDC2 input. + vindcdc3-supply : VDCDC3 input. + vldo1_2-supply : VLDO1 and VLDO2 input. + +Regulator Optional properties: +- defdcdc_default: It's property of DCDC2 and DCDC3 regulators. + 0: If defdcdc pin of DCDC2/DCDC3 is pulled to GND. + 1: If defdcdc pin of DCDC2/DCDC3 is driven HIGH. + If this property is not defined, it defaults to 0 (not enabled). + +Example: + + pmu: tps6507x@48 { + compatible = "ti,tps6507x"; + reg = <0x48>; + + vindcdc1_2-supply = <&vbat>; + vindcdc3-supply = <...>; + vinldo1_2-supply = <...>; + + regulators { + #address-cells = <1>; + #size-cells = <0>; + + vdcdc1_reg: regulator@0 { + regulator-compatible = "VDCDC1"; + reg = <0>; + regulator-min-microvolt = <3150000>; + regulator-max-microvolt = <3450000>; + regulator-always-on; + regulator-boot-on; + }; + vdcdc2_reg: regulator@1 { + regulator-compatible = "VDCDC2"; + reg = <1>; + regulator-min-microvolt = <1710000>; + regulator-max-microvolt = <3450000>; + regulator-always-on; + regulator-boot-on; + defdcdc_default = <1>; + }; + vdcdc3_reg: regulator@2 { + regulator-compatible = "VDCDC3"; + reg = <2>; + regulator-min-microvolt = <950000> + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + defdcdc_default = <1>; + }; + ldo1_reg: regulator@3 { + regulator-compatible = "LDO1"; + reg = <3>; + regulator-min-microvolt = <1710000>; + regulator-max-microvolt = <1890000>; + regulator-always-on; + regulator-boot-on; + }; + ldo2_reg: regulator@4 { + regulator-compatible = "LDO2"; + reg = <4>; + regulator-min-microvolt = <1140000>; + regulator-max-microvolt = <1320000>; + regulator-always-on; + regulator-boot-on; + }; + }; + + }; diff --git a/Documentation/devicetree/bindings/mips/cavium/dma-engine.txt b/Documentation/devicetree/bindings/mips/cavium/dma-engine.txt index cb4291e..a5bdff4 100644 --- a/Documentation/devicetree/bindings/mips/cavium/dma-engine.txt +++ b/Documentation/devicetree/bindings/mips/cavium/dma-engine.txt @@ -1,7 +1,7 @@ * DMA Engine. The Octeon DMA Engine transfers between the Boot Bus and main memory. -The DMA Engine will be refered to by phandle by any device that is +The DMA Engine will be referred to by phandle by any device that is connected to it. Properties: diff --git a/Documentation/devicetree/bindings/mips/cpu_irq.txt b/Documentation/devicetree/bindings/mips/cpu_irq.txt new file mode 100644 index 0000000..13aa4b6 --- /dev/null +++ b/Documentation/devicetree/bindings/mips/cpu_irq.txt @@ -0,0 +1,47 @@ +MIPS CPU interrupt controller + +On MIPS the mips_cpu_intc_init() helper can be used to initialize the 8 CPU +IRQs from a devicetree file and create a irq_domain for IRQ controller. + +With the irq_domain in place we can describe how the 8 IRQs are wired to the +platforms internal interrupt controller cascade. + +Below is an example of a platform describing the cascade inside the devicetree +and the code used to load it inside arch_init_irq(). + +Required properties: +- compatible : Should be "mti,cpu-interrupt-controller" + +Example devicetree: + cpu-irq: cpu-irq@0 { + #address-cells = <0>; + + interrupt-controller; + #interrupt-cells = <1>; + + compatible = "mti,cpu-interrupt-controller"; + }; + + intc: intc@200 { + compatible = "ralink,rt2880-intc"; + reg = <0x200 0x100>; + + interrupt-controller; + #interrupt-cells = <1>; + + interrupt-parent = <&cpu-irq>; + interrupts = <2>; + }; + + +Example platform irq.c: +static struct of_device_id __initdata of_irq_ids[] = { + { .compatible = "mti,cpu-interrupt-controller", .data = mips_cpu_intc_init }, + { .compatible = "ralink,rt2880-intc", .data = intc_of_init }, + {}, +}; + +void __init arch_init_irq(void) +{ + of_irq_init(of_irq_ids); +} diff --git a/Documentation/devicetree/bindings/mmc/brcm,bcm2835-sdhci.txt b/Documentation/devicetree/bindings/mmc/brcm,bcm2835-sdhci.txt new file mode 100644 index 0000000..59476fb --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/brcm,bcm2835-sdhci.txt @@ -0,0 +1,18 @@ +Broadcom BCM2835 SDHCI controller + +This file documents differences between the core properties described +by mmc.txt and the properties that represent the BCM2835 controller. + +Required properties: +- compatible : Should be "brcm,bcm2835-sdhci". +- clocks : The clock feeding the SDHCI controller. + +Example: + +sdhci: sdhci { + compatible = "brcm,bcm2835-sdhci"; + reg = <0x7e300000 0x100>; + interrupts = <2 30>; + clocks = <&clk_mmc>; + bus-width = <4>; +}; diff --git a/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt index 7927689..6d1c098 100644 --- a/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt @@ -4,18 +4,18 @@ The Synopsis designware mobile storage host controller is used to interface a SoC with storage medium such as eMMC or SD/MMC cards. This file documents differences between the core Synopsis dw mshc controller properties described -by synposis-dw-mshc.txt and the properties used by the Samsung Exynos specific +by synopsis-dw-mshc.txt and the properties used by the Samsung Exynos specific extensions to the Synopsis Designware Mobile Storage Host Controller. Required Properties: * compatible: should be - "samsung,exynos4210-dw-mshc": for controllers with Samsung Exynos4210 - specific extentions. + specific extensions. - "samsung,exynos4412-dw-mshc": for controllers with Samsung Exynos4412 - specific extentions. + specific extensions. - "samsung,exynos5250-dw-mshc": for controllers with Samsung Exynos5250 - specific extentions. + specific extensions. * samsung,dw-mshc-ciu-div: Specifies the divider value for the card interface unit (ciu) clock. This property is applicable only for Exynos5 SoC's and diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt index a591c67..85aada2 100644 --- a/Documentation/devicetree/bindings/mmc/mmc.txt +++ b/Documentation/devicetree/bindings/mmc/mmc.txt @@ -6,23 +6,45 @@ Interpreted by the OF core: - reg: Registers location and length. - interrupts: Interrupts used by the MMC controller. -Required properties: -- bus-width: Number of data lines, can be <1>, <4>, or <8> - Card detection: -If no property below is supplied, standard SDHCI card detect is used. +If no property below is supplied, host native card detect is used. Only one of the properties in this section should be supplied: - broken-cd: There is no card detection available; polling must be used. - cd-gpios: Specify GPIOs for card detection, see gpio binding - non-removable: non-removable slot (like eMMC); assume always present. Optional properties: +- bus-width: Number of data lines, can be <1>, <4>, or <8>. The default + will be <1> if the property is absent. - wp-gpios: Specify GPIOs for write protection, see gpio binding -- cd-inverted: when present, polarity on the cd gpio line is inverted -- wp-inverted: when present, polarity on the wp gpio line is inverted +- cd-inverted: when present, polarity on the CD line is inverted. See the note + below for the case, when a GPIO is used for the CD line +- wp-inverted: when present, polarity on the WP line is inverted. See the note + below for the case, when a GPIO is used for the WP line - max-frequency: maximum operating clock frequency - no-1-8-v: when present, denotes that 1.8v card voltage is not supported on this system, even if the controller claims it is. +- cap-sd-highspeed: SD high-speed timing is supported +- cap-mmc-highspeed: MMC high-speed timing is supported +- cap-power-off-card: powering off the card is safe +- cap-sdio-irq: enable SDIO IRQ signalling on this interface + +*NOTE* on CD and WP polarity. To use common for all SD/MMC host controllers line +polarity properties, we have to fix the meaning of the "normal" and "inverted" +line levels. We choose to follow the SDHCI standard, which specifies both those +lines as "active low." Therefore, using the "cd-inverted" property means, that +the CD line is active high, i.e. it is high, when a card is inserted. Similar +logic applies to the "wp-inverted" property. + +CD and WP lines can be implemented on the hardware in one of two ways: as GPIOs, +specified in cd-gpios and wp-gpios properties, or as dedicated pins. Polarity of +dedicated pins can be specified, using *-inverted properties. GPIO polarity can +also be specified using the OF_GPIO_ACTIVE_LOW flag. This creates an ambiguity +in the latter case. We choose to use the XOR logic for GPIO CD and WP lines. +This means, the two properties are "superimposed," for example leaving the +OF_GPIO_ACTIVE_LOW flag clear and specifying the respective *-inverted +property results in a double-inversion and actually means the "normal" line +polarity is in effect. Optional SDIO properties: - keep-power-in-suspend: Preserves card power during a suspend/resume cycle diff --git a/Documentation/devicetree/bindings/mmc/orion-sdio.txt b/Documentation/devicetree/bindings/mmc/orion-sdio.txt new file mode 100644 index 0000000..84f0ebd --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/orion-sdio.txt @@ -0,0 +1,17 @@ +* Marvell orion-sdio controller + +This file documents differences between the core properties in mmc.txt +and the properties used by the orion-sdio driver. + +- compatible: Should be "marvell,orion-sdio" +- clocks: reference to the clock of the SDIO interface + +Example: + + mvsdio@d00d4000 { + compatible = "marvell,orion-sdio"; + reg = <0xd00d4000 0x200>; + interrupts = <54>; + clocks = <&gateclk 17>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt b/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt index 97e9e31..3b3a1ee 100644 --- a/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt +++ b/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt @@ -55,5 +55,5 @@ Example: }; Note: This example shows both SoC specific and board specific properties - in a single device node. The properties can be actually be seperated + in a single device node. The properties can be actually be separated into SoC specific node and board specific node. diff --git a/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt index 06cd32d08..726fd21 100644 --- a/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt @@ -26,8 +26,16 @@ Required Properties: * bus-width: as documented in mmc core bindings. * wp-gpios: specifies the write protect gpio line. The format of the - gpio specifier depends on the gpio controller. If the write-protect - line is not available, this property is optional. + gpio specifier depends on the gpio controller. If a GPIO is not used + for write-protect, this property is optional. + + * disable-wp: If the wp-gpios property isn't present then (by default) + we'd assume that the write protect is hooked up directly to the + controller's special purpose write protect line (accessible via + the WRTPRT register). However, it's possible that we simply don't + want write protect. In that case specify 'disable-wp'. + NOTE: This property is not required for slots known to always + connect to eMMC or SDIO cards. Optional properties: diff --git a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt new file mode 100644 index 0000000..df204e1 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt @@ -0,0 +1,20 @@ +* Toshiba Mobile IO SD/MMC controller + +The tmio-mmc driver doesn't probe its devices actively, instead its binding to +devices is managed by either MFD drivers or by the sh_mobile_sdhi platform +driver. Those drivers supply the tmio-mmc driver with platform data, that either +describe hardware capabilities, known to them, or are obtained by them from +their own platform data or from their DT information. In the latter case all +compulsory and any optional properties, common to all SD/MMC drivers, as +described in mmc.txt, can be used. Additionally the following tmio_mmc-specific +optional bindings can be used. + +Optional properties: +- toshiba,mmc-wrprotect-disable: write-protect detection is unavailable + +When used with Renesas SDHI hardware, the following compatibility strings +configure various model-specific properties: + +"renesas,sh7372-sdhi": (default) compatible with SH7372 +"renesas,r8a7740-sdhi": compatible with R8A7740: certain MMC/SD commands have to + wait for the interface to become idle. diff --git a/Documentation/devicetree/bindings/mtd/elm.txt b/Documentation/devicetree/bindings/mtd/elm.txt new file mode 100644 index 0000000..8c1528c --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/elm.txt @@ -0,0 +1,16 @@ +Error location module + +Required properties: +- compatible: Must be "ti,am33xx-elm" +- reg: physical base address and size of the registers map. +- interrupts: Interrupt number for the elm. + +Optional properties: +- ti,hwmods: Name of the hwmod associated to the elm + +Example: +elm: elm@0 { + compatible = "ti,am3352-elm"; + reg = <0x48080000 0x2000>; + interrupts = <4>; +}; diff --git a/Documentation/devicetree/bindings/mtd/fsmc-nand.txt b/Documentation/devicetree/bindings/mtd/fsmc-nand.txt index e3ea32e..2240ac0 100644 --- a/Documentation/devicetree/bindings/mtd/fsmc-nand.txt +++ b/Documentation/devicetree/bindings/mtd/fsmc-nand.txt @@ -1,7 +1,7 @@ * FSMC NAND Required properties: -- compatible : "st,spear600-fsmc-nand" +- compatible : "st,spear600-fsmc-nand", "stericsson,fsmc-nand" - reg : Address range of the mtd chip - reg-names: Should contain the reg names "fsmc_regs", "nand_data", "nand_addr" and "nand_cmd" diff --git a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt new file mode 100644 index 0000000..e7f8d7e --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt @@ -0,0 +1,80 @@ +Device tree bindings for GPMC connected NANDs + +GPMC connected NAND (found on OMAP boards) are represented as child nodes of +the GPMC controller with a name of "nand". + +All timing relevant properties as well as generic gpmc child properties are +explained in a separate documents - please refer to +Documentation/devicetree/bindings/bus/ti-gpmc.txt + +For NAND specific properties such as ECC modes or bus width, please refer to +Documentation/devicetree/bindings/mtd/nand.txt + + +Required properties: + + - reg: The CS line the peripheral is connected to + +Optional properties: + + - nand-bus-width: Set this numeric value to 16 if the hardware + is wired that way. If not specified, a bus + width of 8 is assumed. + + - ti,nand-ecc-opt: A string setting the ECC layout to use. One of: + + "sw" Software method (default) + "hw" Hardware method + "hw-romcode" gpmc hamming mode method & romcode layout + "bch4" 4-bit BCH ecc code + "bch8" 8-bit BCH ecc code + + - elm_id: Specifies elm device node. This is required to support BCH + error correction using ELM module. + +For inline partiton table parsing (optional): + + - #address-cells: should be set to 1 + - #size-cells: should be set to 1 + +Example for an AM33xx board: + + gpmc: gpmc@50000000 { + compatible = "ti,am3352-gpmc"; + ti,hwmods = "gpmc"; + reg = <0x50000000 0x1000000>; + interrupts = <100>; + gpmc,num-cs = <8>; + gpmc,num-waitpins = <2>; + #address-cells = <2>; + #size-cells = <1>; + ranges = <0 0 0x08000000 0x2000>; /* CS0: NAND */ + elm_id = <&elm>; + + nand@0,0 { + reg = <0 0 0>; /* CS0, offset 0 */ + nand-bus-width = <16>; + ti,nand-ecc-opt = "bch8"; + + gpmc,sync-clk = <0>; + gpmc,cs-on = <0>; + gpmc,cs-rd-off = <44>; + gpmc,cs-wr-off = <44>; + gpmc,adv-on = <6>; + gpmc,adv-rd-off = <34>; + gpmc,adv-wr-off = <44>; + gpmc,we-off = <40>; + gpmc,oe-off = <54>; + gpmc,access = <64>; + gpmc,rd-cycle = <82>; + gpmc,wr-cycle = <82>; + gpmc,wr-access = <40>; + gpmc,wr-data-mux-bus = <0>; + + #address-cells = <1>; + #size-cells = <1>; + + /* partitions go here */ + }; + }; + diff --git a/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt b/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt new file mode 100644 index 0000000..deec9da --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt @@ -0,0 +1,43 @@ +Device tree bindings for GPMC connected OneNANDs + +GPMC connected OneNAND (found on OMAP boards) are represented as child nodes of +the GPMC controller with a name of "onenand". + +All timing relevant properties as well as generic gpmc child properties are +explained in a separate documents - please refer to +Documentation/devicetree/bindings/bus/ti-gpmc.txt + +Required properties: + + - reg: The CS line the peripheral is connected to + +Optional properties: + + - dma-channel: DMA Channel index + +For inline partiton table parsing (optional): + + - #address-cells: should be set to 1 + - #size-cells: should be set to 1 + +Example for an OMAP3430 board: + + gpmc: gpmc@6e000000 { + compatible = "ti,omap3430-gpmc"; + ti,hwmods = "gpmc"; + reg = <0x6e000000 0x1000000>; + interrupts = <20>; + gpmc,num-cs = <8>; + gpmc,num-waitpins = <4>; + #address-cells = <2>; + #size-cells = <1>; + + onenand@0 { + reg = <0 0 0>; /* CS0, offset 0 */ + + #address-cells = <1>; + #size-cells = <1>; + + /* partitions go here */ + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/mtd-physmap.txt b/Documentation/devicetree/bindings/mtd/mtd-physmap.txt index dab7847..61c5ec8 100644 --- a/Documentation/devicetree/bindings/mtd/mtd-physmap.txt +++ b/Documentation/devicetree/bindings/mtd/mtd-physmap.txt @@ -26,6 +26,9 @@ file systems on embedded devices. - linux,mtd-name: allow to specify the mtd name for retro capability with physmap-flash drivers as boot loader pass the mtd partition via the old device name physmap-flash. + - use-advanced-sector-protection: boolean to enable support for the + advanced sector protection (Spansion: PPB - Persistent Protection + Bits) locking. For JEDEC compatible devices, the following additional properties are defined: diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt index 6ddd028..ecfdf75 100644 --- a/Documentation/devicetree/bindings/net/cpsw.txt +++ b/Documentation/devicetree/bindings/net/cpsw.txt @@ -24,6 +24,8 @@ Required properties: Optional properties: - ti,hwmods : Must be "cpgmac0" - no_bd_ram : Must be 0 or 1 +- dual_emac : Specifies Switch to act as Dual EMAC +- dual_emac_res_vlan : Specifies VID to be used to segregate the ports Note: "ti,hwmods" field is used to fetch the base address and irq resources from TI, omap hwmod data base during device registration. diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt new file mode 100644 index 0000000..dff0e5f --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt @@ -0,0 +1,60 @@ +* Allwinner A1X Pin Controller + +The pins controlled by sunXi pin controller are organized in banks, +each bank has 32 pins. Each pin has 7 multiplexing functions, with +the first two functions being GPIO in and out. The configuration on +the pins includes drive strength and pull-up. + +Required properties: +- compatible: "allwinner,<soc>-pinctrl". Supported SoCs for now are: + sun5i-a13. +- reg: Should contain the register physical address and length for the + pin controller. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices. + +A pinctrl node should contain at least one subnodes representing the +pinctrl groups available on the machine. Each subnode will list the +pins it needs, and how they should be configured, with regard to muxer +configuration, drive strength and pullups. If one of these options is +not set, its actual value will be unspecified. + +Required subnode-properties: + +- allwinner,pins: List of strings containing the pin name. +- allwinner,function: Function to mux the pins listed above to. + +Optional subnode-properties: +- allwinner,drive: Integer. Represents the current sent to the pin + 0: 10 mA + 1: 20 mA + 2: 30 mA + 3: 40 mA +- allwinner,pull: Integer. + 0: No resistor + 1: Pull-up resistor + 2: Pull-down resistor + +Examples: + +pinctrl@01c20800 { + compatible = "allwinner,sun5i-a13-pinctrl"; + reg = <0x01c20800 0x400>; + #address-cells = <1>; + #size-cells = <0>; + + uart1_pins_a: uart1@0 { + allwinner,pins = "PE10", "PE11"; + allwinner,function = "uart1"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + + uart1_pins_b: uart1@1 { + allwinner,pins = "PG3", "PG4"; + allwinner,function = "uart1"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; +}; diff --git a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra114-pinmux.txt b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra114-pinmux.txt new file mode 100644 index 0000000..e204d00 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra114-pinmux.txt @@ -0,0 +1,120 @@ +NVIDIA Tegra114 pinmux controller + +The Tegra114 pinctrl binding is very similar to the Tegra20 and Tegra30 +pinctrl binding, as described in nvidia,tegra20-pinmux.txt and +nvidia,tegra30-pinmux.txt. In fact, this document assumes that binding as +a baseline, and only documents the differences between the two bindings. + +Required properties: +- compatible: "nvidia,tegra114-pinmux" +- reg: Should contain the register physical address and length for each of + the pad control and mux registers. The first bank of address must be the + driver strength pad control register address and second bank address must + be pinmux register address. + +Tegra114 adds the following optional properties for pin configuration subnodes: +- nvidia,enable-input: Integer. Enable the pin's input path. 0: no, 1: yes. +- nvidia,open-drain: Integer. Enable open drain mode. 0: no, 1: yes. +- nvidia,lock: Integer. Lock the pin configuration against further changes + until reset. 0: no, 1: yes. +- nvidia,io-reset: Integer. Reset the IO path. 0: no, 1: yes. +- nvidia,rcv-sel: Integer. Select VIL/VIH receivers. 0: normal, 1: high. +- nvidia,drive-type: Integer. Valid range 0...3. + +As with Tegra20 and Terga30, see the Tegra TRM for complete details regarding +which groups support which functionality. + +Valid values for pin and group names are: + + per-pin mux groups: + + These all support nvidia,function, nvidia,tristate, nvidia,pull, + nvidia,enable-input, nvidia,lock. Some support nvidia,open-drain, + nvidia,io-reset and nvidia,rcv-sel. + + ulpi_data0_po1, ulpi_data1_po2, ulpi_data2_po3, ulpi_data3_po4, + ulpi_data4_po5, ulpi_data5_po6, ulpi_data6_po7, ulpi_data7_po0, + ulpi_clk_py0, ulpi_dir_py1, ulpi_nxt_py2, ulpi_stp_py3, dap3_fs_pp0, + dap3_din_pp1, dap3_dout_pp2, dap3_sclk_pp3, pv0, pv1, sdmmc1_clk_pz0, + sdmmc1_cmd_pz1, sdmmc1_dat3_py4, sdmmc1_dat2_py5, sdmmc1_dat1_py6, + sdmmc1_dat0_py7, clk2_out_pw5, clk2_req_pcc5, hdmi_int_pn7, ddc_scl_pv4, + ddc_sda_pv5, uart2_rxd_pc3, uart2_txd_pc2, uart2_rts_n_pj6, + uart2_cts_n_pj5, uart3_txd_pw6, uart3_rxd_pw7, uart3_cts_n_pa1, + uart3_rts_n_pc0, pu0, pu1, pu2, pu3, pu4, pu5, pu6, gen1_i2c_sda_pc5, + gen1_i2c_scl_pc4, dap4_fs_pp4, dap4_din_pp5, dap4_dout_pp6, dap4_sclk_pp7, + clk3_out_pee0, clk3_req_pee1, gmi_wp_n_pc7, gmi_iordy_pi5, gmi_wait_pi7, + gmi_adv_n_pk0, gmi_clk_pk1, gmi_cs0_n_pj0, gmi_cs1_n_pj2, gmi_cs2_n_pk3, + gmi_cs3_n_pk4, gmi_cs4_n_pk2, gmi_cs6_n_pi3, gmi_cs7_n_pi6, gmi_ad0_pg0, + gmi_ad1_pg1, gmi_ad2_pg2, gmi_ad3_pg3, gmi_ad4_pg4, gmi_ad5_pg5, + gmi_ad6_pg6, gmi_ad7_pg7, gmi_ad8_ph0, gmi_ad9_ph1, gmi_ad10_ph2, + gmi_ad11_ph3, gmi_ad12_ph4, gmi_ad13_ph5, gmi_ad14_ph6, gmi_ad15_ph7, + gmi_a16_pj7, gmi_a17_pb0, gmi_a18_pb1, gmi_a19_pk7, gmi_wr_n_pi0, + gmi_oe_n_pi1, gmi_dqs_p_pj3, gmi_rst_n_pi4, gen2_i2c_scl_pt5, + gen2_i2c_sda_pt6, sdmmc4_clk_pcc4, sdmmc4_cmd_pt7, sdmmc4_dat0_paa0, + sdmmc4_dat1_paa1, sdmmc4_dat2_paa2, sdmmc4_dat3_paa3, sdmmc4_dat4_paa4, + sdmmc4_dat5_paa5, sdmmc4_dat6_paa6, sdmmc4_dat7_paa7, cam_mclk_pcc0, + pcc1, pbb0, cam_i2c_scl_pbb1, cam_i2c_sda_pbb2, pbb3, pbb4, pbb5, pbb6, + pbb7, pcc2, pwr_i2c_scl_pz6, pwr_i2c_sda_pz7, kb_row0_pr0, kb_row1_pr1, + kb_row2_pr2, kb_row3_pr3, kb_row4_pr4, kb_row5_pr5, kb_row6_pr6, + kb_row7_pr7, kb_row8_ps0, kb_row9_ps1, kb_row10_ps2, kb_col0_pq0, + kb_col1_pq1, kb_col2_pq2, kb_col3_pq3, kb_col4_pq4, kb_col5_pq5, + kb_col6_pq6, kb_col7_pq7, clk_32k_out_pa0, sys_clk_req_pz5, core_pwr_req, + cpu_pwr_req, pwr_int_n, owr, dap1_fs_pn0, dap1_din_pn1, dap1_dout_pn2, + dap1_sclk_pn3, clk1_req_pee2, clk1_out_pw4, spdif_in_pk6, spdif_out_pk5, + dap2_fs_pa2, dap2_din_pa4, dap2_dout_pa5, dap2_sclk_pa3, dvfs_pwm_px0, + gpio_x1_aud_px1, gpio_x3_aud_px3, dvfs_clk_px2, gpio_x4_aud_px4, + gpio_x5_aud_px5, gpio_x6_aud_px6, gpio_x7_aud_px7, sdmmc3_clk_pa6, + sdmmc3_cmd_pa7, sdmmc3_dat0_pb7, sdmmc3_dat1_pb6, sdmmc3_dat2_pb5, + sdmmc3_dat3_pb4, hdmi_cec_pee3, sdmmc1_wp_n_pv3, sdmmc3_cd_n_pv2, + gpio_w2_aud_pw2, gpio_w3_aud_pw3, usb_vbus_en0_pn4, usb_vbus_en1_pn5, + sdmmc3_clk_lb_in_pee5, sdmmc3_clk_lb_out_pee4, reset_out_n. + + drive groups: + + These all support nvidia,pull-down-strength, nvidia,pull-up-strength, + nvidia,slew-rate-rising, nvidia,slew-rate-falling. Most but not all + support nvidia,high-speed-mode, nvidia,schmitt, nvidia,low-power-mode + and nvidia,drive-type. + + ao1, ao2, at1, at2, at3, at4, at5, cdev1, cdev2, dap1, dap2, dap3, dap4, + dbg, sdio3, spi, uaa, uab, uart2, uart3, sdio1, ddc, gma, gme, gmf, gmg, + gmh, owr, uda. + +Example: + + pinmux: pinmux { + compatible = "nvidia,tegra114-pinmux"; + reg = <0x70000868 0x148 /* Pad control registers */ + 0x70003000 0x40c>; /* PinMux registers */ + }; + +Example board file extract: + + pinctrl { + sdmmc4_default: pinmux { + sdmmc4_clk_pcc4 { + nvidia,pins = "sdmmc4_clk_pcc4", + nvidia,function = "sdmmc4"; + nvidia,pull = <0>; + nvidia,tristate = <0>; + }; + sdmmc4_dat0_paa0 { + nvidia,pins = "sdmmc4_dat0_paa0", + "sdmmc4_dat1_paa1", + "sdmmc4_dat2_paa2", + "sdmmc4_dat3_paa3", + "sdmmc4_dat4_paa4", + "sdmmc4_dat5_paa5", + "sdmmc4_dat6_paa6", + "sdmmc4_dat7_paa7"; + nvidia,function = "sdmmc4"; + nvidia,pull = <2>; + nvidia,tristate = <0>; + }; + }; + }; + + sdhci@78000400 { + pinctrl-names = "default"; + pinctrl-0 = <&sdmmc4_default>; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt index e97a278..4598a47 100644 --- a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt @@ -7,9 +7,9 @@ on-chip controllers onto these pads. Required Properties: - compatible: should be one of the following. - - "samsung,pinctrl-exynos4210": for Exynos4210 compatible pin-controller. - - "samsung,pinctrl-exynos4x12": for Exynos4x12 compatible pin-controller. - - "samsung,pinctrl-exynos5250": for Exynos5250 compatible pin-controller. + - "samsung,exynos4210-pinctrl": for Exynos4210 compatible pin-controller. + - "samsung,exynos4x12-pinctrl": for Exynos4x12 compatible pin-controller. + - "samsung,exynos5250-pinctrl": for Exynos5250 compatible pin-controller. - reg: Base address of the pin controller hardware module and length of the address space it occupies. @@ -142,7 +142,7 @@ the following format 'pinctrl{n}' where n is a unique number for the alias. Example: A pin-controller node with pin banks: pinctrl_0: pinctrl@11400000 { - compatible = "samsung,pinctrl-exynos4210"; + compatible = "samsung,exynos4210-pinctrl"; reg = <0x11400000 0x1000>; interrupts = <0 47 0>; @@ -185,7 +185,7 @@ Example: A pin-controller node with pin banks: Example 1: A pin-controller node with pin groups. pinctrl_0: pinctrl@11400000 { - compatible = "samsung,pinctrl-exynos4210"; + compatible = "samsung,exynos4210-pinctrl"; reg = <0x11400000 0x1000>; interrupts = <0 47 0>; @@ -230,7 +230,7 @@ Example 1: A pin-controller node with pin groups. Example 2: A pin-controller node with external wakeup interrupt controller node. pinctrl_1: pinctrl@11000000 { - compatible = "samsung,pinctrl-exynos4210"; + compatible = "samsung,exynos4210-pinctrl"; reg = <0x11000000 0x1000>; interrupts = <0 46 0> diff --git a/Documentation/devicetree/bindings/pinctrl/ste,nomadik.txt b/Documentation/devicetree/bindings/pinctrl/ste,nomadik.txt new file mode 100644 index 0000000..9a2f3f4 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/ste,nomadik.txt @@ -0,0 +1,140 @@ +ST Ericsson Nomadik pinmux controller + +Required properties: +- compatible: "stericsson,nmk-pinctrl", "stericsson,nmk-pinctrl-db8540", + "stericsson,nmk-pinctrl-stn8815" +- reg: Should contain the register physical address and length of the PRCMU. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +ST Ericsson's pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as input, output, pull up, pull down... + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Required subnode-properties: +- ste,pins : An array of strings. Each string contains the name of a pin or + group. + +Optional subnode-properties: +- ste,function: A string containing the name of the function to mux to the + pin or group. + +- ste,config: Handle of pin configuration node (e.g. ste,config = <&slpm_in_wkup_pdis>) + +- ste,input : <0/1/2> + 0: input with no pull + 1: input with pull up, + 2: input with pull down, + +- ste,output: <0/1/2> + 0: output low, + 1: output high, + 2: output (value is not specified). + +- ste,sleep: <0/1> + 0: sleep mode disable, + 1: sleep mode enable. + +- ste,sleep-input: <0/1/2/3> + 0: sleep input with no pull, + 1: sleep input with pull up, + 2: sleep input with pull down. + 3: sleep input and keep last input configuration (no pull, pull up or pull down). + +- ste,sleep-output: <0/1/2> + 0: sleep output low, + 1: sleep output high, + 2: sleep output (value is not specified). + +- ste,sleep-gpio: <0/1> + 0: disable sleep gpio mode, + 1: enable sleep gpio mode. + +- ste,sleep-wakeup: <0/1> + 0: wake-up detection enabled, + 1: wake-up detection disabled. + +- ste,sleep-pull-disable: <0/1> + 0: GPIO pull-up or pull-down resistor is enabled, when pin is an input, + 1: GPIO pull-up and pull-down resistor are disabled. + +Example board file extract: + + pinctrl@80157000 { + compatible = "stericsson,nmk-pinctrl"; + reg = <0x80157000 0x2000>; + + pinctrl-names = "default"; + + slpm_in_wkup_pdis: slpm_in_wkup_pdis { + ste,sleep = <1>; + ste,sleep-input = <3>; + ste,sleep-wakeup = <1>; + ste,sleep-pull-disable = <0>; + }; + + slpm_out_hi_wkup_pdis: slpm_out_hi_wkup_pdis { + ste,sleep = <1>; + ste,sleep-output = <1>; + ste,sleep-wakeup = <1>; + ste,sleep-pull-disable = <0>; + }; + + slpm_out_wkup_pdis: slpm_out_wkup_pdis { + ste,sleep = <1>; + ste,sleep-output = <2>; + ste,sleep-wakeup = <1>; + ste,sleep-pull-disable = <0>; + }; + + uart0 { + uart0_default_mux: uart0_mux { + u0_default_mux { + ste,function = "u0"; + ste,pins = "u0_a_1"; + }; + }; + uart0_default_mode: uart0_default { + uart0_default_cfg1 { + ste,pins = "GPIO0", "GPIO2"; + ste,input = <1>; + }; + + uart0_default_cfg2 { + ste,pins = "GPIO1", "GPIO3"; + ste,output = <1>; + }; + }; + uart0_sleep_mode: uart0_sleep { + uart0_sleep_cfg1 { + ste,pins = "GPIO0", "GPIO2"; + ste,config = <&slpm_in_wkup_pdis>; + }; + uart0_sleep_cfg2 { + ste,pins = "GPIO1"; + ste,config = <&slpm_out_hi_wkup_pdis>; + }; + uart0_sleep_cfg3 { + ste,pins = "GPIO3"; + ste,config = <&slpm_out_wkup_pdis>; + }; + }; + }; + }; + + uart@80120000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x80120000 0x1000>; + interrupts = <0 11 0x4>; + + pinctrl-names = "default","sleep"; + pinctrl-0 = <&uart0_default_mux>, <&uart0_default_mode>; + pinctrl-1 = <&uart0_sleep_mode>; + }; diff --git a/Documentation/devicetree/bindings/power_supply/max8925_batter.txt b/Documentation/devicetree/bindings/power_supply/max8925_batter.txt new file mode 100644 index 0000000..d7e3e0c --- /dev/null +++ b/Documentation/devicetree/bindings/power_supply/max8925_batter.txt @@ -0,0 +1,18 @@ +max8925-battery bindings +~~~~~~~~~~~~~~~~ + +Optional properties : + - batt-detect: whether support battery detect + - topoff-threshold: set charging current in topoff mode + - fast-charge: set charging current in fast mode + - no-temp-support: whether support temperature protection detect + - no-insert-detect: whether support insert detect + +Example: + charger { + batt-detect = <0>; + topoff-threshold = <1>; + fast-charge = <7>; + no-temp-support = <0>; + no-insert-detect = <0>; + }; diff --git a/Documentation/devicetree/bindings/power_supply/qnap-poweroff.txt b/Documentation/devicetree/bindings/power_supply/qnap-poweroff.txt new file mode 100644 index 0000000..9a599d2 --- /dev/null +++ b/Documentation/devicetree/bindings/power_supply/qnap-poweroff.txt @@ -0,0 +1,13 @@ +* QNAP Power Off + +QNAP NAS devices have a microcontroller controlling the main power +supply. This microcontroller is connected to UART1 of the Kirkwood and +Orion5x SoCs. Sending the charactor 'A', at 19200 baud, tells the +microcontroller to turn the power off. This driver adds a handler to +pm_power_off which is called to turn the power off. + +Required Properties: +- compatible: Should be "qnap,power-off" + +- reg: Address and length of the register set for UART1 +- clocks: tclk clock diff --git a/Documentation/devicetree/bindings/power_supply/restart-poweroff.txt b/Documentation/devicetree/bindings/power_supply/restart-poweroff.txt new file mode 100644 index 0000000..5776e68 --- /dev/null +++ b/Documentation/devicetree/bindings/power_supply/restart-poweroff.txt @@ -0,0 +1,8 @@ +* Restart Power Off + +Buffalo Linkstation LS-XHL and LS-CHLv2, and other devices power off +by restarting and letting u-boot keep hold of the machine until the +user presses a button. + +Required Properties: +- compatible: Should be "restart-poweroff" diff --git a/Documentation/devicetree/bindings/powerpc/fsl/guts.txt b/Documentation/devicetree/bindings/powerpc/fsl/guts.txt index 9e7a241..7f150b5 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/guts.txt +++ b/Documentation/devicetree/bindings/powerpc/fsl/guts.txt @@ -17,9 +17,20 @@ Recommended properties: contains a functioning "reset control register" (i.e. the board is wired to reset upon setting the HRESET_REQ bit in this register). -Example: + - fsl,liodn-bits : Indicates the number of defined bits in the LIODN + registers, for those SOCs that have a PAMU device. + +Examples: global-utilities@e0000 { /* global utilities block */ compatible = "fsl,mpc8548-guts"; reg = <e0000 1000>; fsl,has-rstcr; }; + + guts: global-utilities@e0000 { + compatible = "fsl,qoriq-device-config-1.0"; + reg = <0xe0000 0xe00>; + fsl,has-rstcr; + #sleep-cells = <1>; + fsl,liodn-bits = <12>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/pamu.txt b/Documentation/devicetree/bindings/powerpc/fsl/pamu.txt new file mode 100644 index 0000000..1f5e329 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/pamu.txt @@ -0,0 +1,140 @@ +Freescale Peripheral Management Access Unit (PAMU) Device Tree Binding + +DESCRIPTION + +The PAMU is an I/O MMU that provides device-to-memory access control and +address translation capabilities. + +Required properties: + +- compatible : <string> + First entry is a version-specific string, such as + "fsl,pamu-v1.0". The second is "fsl,pamu". +- ranges : <prop-encoded-array> + A standard property. Utilized to describe the memory mapped + I/O space utilized by the controller. The size should + be set to the total size of the register space of all + physically present PAMU controllers. For example, for + PAMU v1.0, on an SOC that has five PAMU devices, the size + is 0x5000. +- interrupts : <prop-encoded-array> + Interrupt mappings. The first tuple is the normal PAMU + interrupt, used for reporting access violations. The second + is for PAMU hardware errors, such as PAMU operation errors + and ECC errors. +- #address-cells: <u32> + A standard property. +- #size-cells : <u32> + A standard property. + +Optional properties: +- reg : <prop-encoded-array> + A standard property. It represents the CCSR registers of + all child PAMUs combined. Include it to provide support + for legacy drivers. +- interrupt-parent : <phandle> + Phandle to interrupt controller + +Child nodes: + +Each child node represents one PAMU controller. Each SOC device that is +connected to a specific PAMU device should have a "fsl,pamu-phandle" property +that links to the corresponding specific child PAMU controller. + +- reg : <prop-encoded-array> + A standard property. Specifies the physical address and + length (relative to the parent 'ranges' property) of this + PAMU controller's configuration registers. The size should + be set to the size of this PAMU controllers's register space. + For PAMU v1.0, this size is 0x1000. +- fsl,primary-cache-geometry + : <prop-encoded-array> + Two cells that specify the geometry of the primary PAMU + cache. The first is the number of cache lines, and the + second is the number of "ways". For direct-mapped caches, + specify a value of 1. +- fsl,secondary-cache-geometry + : <prop-encoded-array> + Two cells that specify the geometry of the secondary PAMU + cache. The first is the number of cache lines, and the + second is the number of "ways". For direct-mapped caches, + specify a value of 1. + +Device nodes: + +Devices that have LIODNs need to specify links to the parent PAMU controller +(the actual PAMU controller that this device is connected to) and a pointer to +the LIODN register, if applicable. + +- fsl,iommu-parent + : <phandle> + Phandle to the single, specific PAMU controller node to which + this device is connect. The PAMU topology is represented in + the device tree to assist code that dynamically determines the + best LIODN values to minimize PAMU cache thrashing. + +- fsl,liodn-reg : <prop-encoded-array> + Two cells that specify the location of the LIODN register + for this device. Required for devices that have a single + LIODN. The first cell is a phandle to a node that contains + the registers where the LIODN is to be set. The second is + the offset from the first "reg" resource of the node where + the specific LIODN register is located. + + +Example: + + iommu@20000 { + compatible = "fsl,pamu-v1.0", "fsl,pamu"; + reg = <0x20000 0x5000>; + ranges = <0 0x20000 0x5000>; + #address-cells = <1>; + #size-cells = <1>; + interrupts = < + 24 2 0 0 + 16 2 1 30>; + + pamu0: pamu@0 { + reg = <0 0x1000>; + fsl,primary-cache-geometry = <32 1>; + fsl,secondary-cache-geometry = <128 2>; + }; + + pamu1: pamu@1000 { + reg = <0x1000 0x1000>; + fsl,primary-cache-geometry = <32 1>; + fsl,secondary-cache-geometry = <128 2>; + }; + + pamu2: pamu@2000 { + reg = <0x2000 0x1000>; + fsl,primary-cache-geometry = <32 1>; + fsl,secondary-cache-geometry = <128 2>; + }; + + pamu3: pamu@3000 { + reg = <0x3000 0x1000>; + fsl,primary-cache-geometry = <32 1>; + fsl,secondary-cache-geometry = <128 2>; + }; + + pamu4: pamu@4000 { + reg = <0x4000 0x1000>; + fsl,primary-cache-geometry = <32 1>; + fsl,secondary-cache-geometry = <128 2>; + }; + }; + + guts: global-utilities@e0000 { + compatible = "fsl,qoriq-device-config-1.0"; + reg = <0xe0000 0xe00>; + fsl,has-rstcr; + #sleep-cells = <1>; + fsl,liodn-bits = <12>; + }; + +/include/ "qoriq-dma-0.dtsi" + dma@100300 { + fsl,iommu-parent = <&pamu0>; + fsl,liodn-reg = <&guts 0x584>; /* DMA2LIODNR */ + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/srio.txt b/Documentation/devicetree/bindings/powerpc/fsl/srio.txt index b039bcb..07abf0f 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/srio.txt +++ b/Documentation/devicetree/bindings/powerpc/fsl/srio.txt @@ -8,9 +8,9 @@ Properties: Definition: Must include "fsl,srio" for IP blocks with IP Block Revision Register (SRIO IPBRR1) Major ID equal to 0x01c0. - Optionally, a compatiable string of "fsl,srio-vX.Y" where X is Major + Optionally, a compatible string of "fsl,srio-vX.Y" where X is Major version in IP Block Revision Register and Y is Minor version. If this - compatiable is provided it should be ordered before "fsl,srio". + compatible is provided it should be ordered before "fsl,srio". - reg Usage: required diff --git a/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt b/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt new file mode 100644 index 0000000..de0eaed --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt @@ -0,0 +1,18 @@ +Atmel TCB PWM controller + +Required properties: +- compatible: should be "atmel,tcb-pwm" +- #pwm-cells: Should be 3. The first cell specifies the per-chip index + of the PWM to use, the second cell is the period in nanoseconds and + bit 0 in the third cell is used to encode the polarity of PWM output. + Set bit 0 of the third cell in PWM specifier to 1 for inverse polarity & + set to 0 for normal polarity. +- tc-block: The Timer Counter block to use as a PWM chip. + +Example: + +pwm { + compatible = "atmel,tcb-pwm"; + #pwm-cells = <3>; + tc-block = <1>; +}; diff --git a/Documentation/devicetree/bindings/pwm/vt8500-pwm.txt b/Documentation/devicetree/bindings/pwm/vt8500-pwm.txt index bcc6367..d21d82d 100644 --- a/Documentation/devicetree/bindings/pwm/vt8500-pwm.txt +++ b/Documentation/devicetree/bindings/pwm/vt8500-pwm.txt @@ -3,14 +3,17 @@ VIA/Wondermedia VT8500/WM8xxx series SoC PWM controller Required properties: - compatible: should be "via,vt8500-pwm" - reg: physical base address and length of the controller's registers -- #pwm-cells: should be 2. The first cell specifies the per-chip index - of the PWM to use and the second cell is the period in nanoseconds. +- #pwm-cells: Should be 3. Number of cells being used to specify PWM property. + First cell specifies the per-chip index of the PWM to use, the second + cell is the period in nanoseconds and bit 0 in the third cell is used to + encode the polarity of PWM output. Set bit 0 of the third in PWM specifier + to 1 for inverse polarity & set to 0 for normal polarity. - clocks: phandle to the PWM source clock Example: pwm1: pwm@d8220000 { - #pwm-cells = <2>; + #pwm-cells = <3>; compatible = "via,vt8500-pwm"; reg = <0xd8220000 0x1000>; clocks = <&clkpwm>; diff --git a/Documentation/devicetree/bindings/regulator/anatop-regulator.txt b/Documentation/devicetree/bindings/regulator/anatop-regulator.txt index 357758c..758eae2 100644 --- a/Documentation/devicetree/bindings/regulator/anatop-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/anatop-regulator.txt @@ -9,6 +9,11 @@ Required properties: - anatop-min-voltage: Minimum voltage of this regulator - anatop-max-voltage: Maximum voltage of this regulator +Optional properties: +- anatop-delay-reg-offset: Anatop MFD step time register offset +- anatop-delay-bit-shift: Bit shift for the step time register +- anatop-delay-bit-width: Number of bits used in the step time register + Any property defined as part of the core regulator binding, defined in regulator.txt, can also be used. @@ -23,6 +28,9 @@ Example: anatop-reg-offset = <0x140>; anatop-vol-bit-shift = <9>; anatop-vol-bit-width = <5>; + anatop-delay-reg-offset = <0x170>; + anatop-delay-bit-shift = <24>; + anatop-delay-bit-width = <2>; anatop-min-bit-val = <1>; anatop-min-voltage = <725000>; anatop-max-voltage = <1300000>; diff --git a/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt b/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt new file mode 100644 index 0000000..a35ff99 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt @@ -0,0 +1,152 @@ +* Samsung S5M8767 Voltage and Current Regulator + +The Samsung S5M8767 is a multi-function device which includes volatage and +current regulators, rtc, charger controller and other sub-blocks. It is +interfaced to the host controller using a i2c interface. Each sub-block is +addressed by the host system using different i2c slave address. This document +describes the bindings for 'pmic' sub-block of s5m8767. + +Required properties: +- compatible: Should be "samsung,s5m8767-pmic". +- reg: Specifies the i2c slave address of the pmic block. It should be 0x66. + +- s5m8767,pmic-buck2-dvs-voltage: A set of 8 voltage values in micro-volt (uV) + units for buck2 when changing voltage using gpio dvs. Refer to [1] below + for additional information. + +- s5m8767,pmic-buck3-dvs-voltage: A set of 8 voltage values in micro-volt (uV) + units for buck3 when changing voltage using gpio dvs. Refer to [1] below + for additional information. + +- s5m8767,pmic-buck4-dvs-voltage: A set of 8 voltage values in micro-volt (uV) + units for buck4 when changing voltage using gpio dvs. Refer to [1] below + for additional information. + +- s5m8767,pmic-buck-ds-gpios: GPIO specifiers for three host gpio's used + for selecting GPIO DVS lines. It is one-to-one mapped to dvs gpio lines. + +[1] If none of the 's5m8767,pmic-buck[2/3/4]-uses-gpio-dvs' optional + property is specified, the 's5m8767,pmic-buck[2/3/4]-dvs-voltage' + property should specify atleast one voltage level (which would be a + safe operating voltage). + + If either of the 's5m8767,pmic-buck[2/3/4]-uses-gpio-dvs' optional + property is specified, then all the eight voltage values for the + 's5m8767,pmic-buck[2/3/4]-dvs-voltage' should be specified. + +Optional properties: +- interrupt-parent: Specifies the phandle of the interrupt controller to which + the interrupts from s5m8767 are delivered to. +- interrupts: Interrupt specifiers for two interrupt sources. + - First interrupt specifier is for 'irq1' interrupt. + - Second interrupt specifier is for 'alert' interrupt. +- s5m8767,pmic-buck2-uses-gpio-dvs: 'buck2' can be controlled by gpio dvs. +- s5m8767,pmic-buck3-uses-gpio-dvs: 'buck3' can be controlled by gpio dvs. +- s5m8767,pmic-buck4-uses-gpio-dvs: 'buck4' can be controlled by gpio dvs. + +Additional properties required if either of the optional properties are used: + +- s5m8767,pmic-buck234-default-dvs-idx: Default voltage setting selected from + the possible 8 options selectable by the dvs gpios. The value of this + property should be between 0 and 7. If not specified or if out of range, the + default value of this property is set to 0. + +- s5m8767,pmic-buck-dvs-gpios: GPIO specifiers for three host gpio's used + for dvs. The format of the gpio specifier depends in the gpio controller. + +Regulators: The regulators of s5m8767 that have to be instantiated should be +included in a sub-node named 'regulators'. Regulator nodes included in this +sub-node should be of the format as listed below. + + regulator_name { + ldo1_reg: LDO1 { + regulator-name = "VDD_ALIVE_1.0V"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + regulator-boot-on; + op_mode = <1>; /* Normal Mode */ + }; + }; +The above regulator entries are defined in regulator bindings documentation +except op_mode description. + - op_mode: describes the different operating modes of the LDO's with + power mode change in SOC. The different possible values are, + 0 - always off mode + 1 - on in normal mode + 2 - low power mode + 3 - suspend mode + +The following are the names of the regulators that the s5m8767 pmic block +supports. Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number +as per the datasheet of s5m8767. + + - LDOn + - valid values for n are 1 to 28 + - Example: LDO0, LD01, LDO28 + - BUCKn + - valid values for n are 1 to 9. + - Example: BUCK1, BUCK2, BUCK9 + +The bindings inside the regulator nodes use the standard regulator bindings +which are documented elsewhere. + +Example: + + s5m8767_pmic@66 { + compatible = "samsung,s5m8767-pmic"; + reg = <0x66>; + + s5m8767,pmic-buck2-uses-gpio-dvs; + s5m8767,pmic-buck3-uses-gpio-dvs; + s5m8767,pmic-buck4-uses-gpio-dvs; + + s5m8767,pmic-buck-default-dvs-idx = <0>; + + s5m8767,pmic-buck-dvs-gpios = <&gpx0 0 1 0 0>, /* DVS1 */ + <&gpx0 1 1 0 0>, /* DVS2 */ + <&gpx0 2 1 0 0>; /* DVS3 */ + + s5m8767,pmic-buck-ds-gpios = <&gpx2 3 1 0 0>, /* SET1 */ + <&gpx2 4 1 0 0>, /* SET2 */ + <&gpx2 5 1 0 0>; /* SET3 */ + + s5m8767,pmic-buck2-dvs-voltage = <1350000>, <1300000>, + <1250000>, <1200000>, + <1150000>, <1100000>, + <1000000>, <950000>; + + s5m8767,pmic-buck3-dvs-voltage = <1100000>, <1100000>, + <1100000>, <1100000>, + <1000000>, <1000000>, + <1000000>, <1000000>; + + s5m8767,pmic-buck4-dvs-voltage = <1200000>, <1200000>, + <1200000>, <1200000>, + <1200000>, <1200000>, + <1200000>, <1200000>; + + regulators { + ldo1_reg: LDO1 { + regulator-name = "VDD_ABB_3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + op_mode = <1>; /* Normal Mode */ + }; + + ldo2_reg: LDO2 { + regulator-name = "VDD_ALIVE_1.1V"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + }; + + buck1_reg: BUCK1 { + regulator-name = "VDD_MIF_1.2V"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/tps51632-regulator.txt b/Documentation/devicetree/bindings/regulator/tps51632-regulator.txt new file mode 100644 index 0000000..2f7e44a --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/tps51632-regulator.txt @@ -0,0 +1,27 @@ +TPS51632 Voltage regulators + +Required properties: +- compatible: Must be "ti,tps51632" +- reg: I2C slave address + +Optional properties: +- ti,enable-pwm-dvfs: Enable the DVFS voltage control through the PWM interface. +- ti,dvfs-step-20mV: The 20mV step voltage when PWM DVFS enabled. Missing this + will set 10mV step voltage in PWM DVFS mode. In normal mode, the voltage + step is 10mV as per datasheet. + +Any property defined as part of the core regulator binding, defined in +regulator.txt, can also be used. + +Example: + + tps51632 { + compatible = "ti,tps51632"; + reg = <0x43>; + regulator-name = "tps51632-vout"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1500000>; + regulator-boot-on; + ti,enable-pwm-dvfs; + ti,dvfs-step-20mV; + }; diff --git a/Documentation/devicetree/bindings/regulator/tps62360-regulator.txt b/Documentation/devicetree/bindings/regulator/tps62360-regulator.txt index c8ca6b8..1b20c3d 100644 --- a/Documentation/devicetree/bindings/regulator/tps62360-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/tps62360-regulator.txt @@ -17,9 +17,9 @@ Optional properties: - ti,vsel1-gpio: Gpio for controlling VSEL1 line. If this property is missing, then assume that there is no GPIO for vsel1 control. -- ti,vsel0-state-high: Inital state of vsel0 input is high. +- ti,vsel0-state-high: Initial state of vsel0 input is high. If this property is missing, then assume the state as low (0). -- ti,vsel1-state-high: Inital state of vsel1 input is high. +- ti,vsel1-state-high: Initial state of vsel1 input is high. If this property is missing, then assume the state as low (0). Any property defined as part of the core regulator binding, defined in diff --git a/Documentation/devicetree/bindings/regulator/tps65090.txt b/Documentation/devicetree/bindings/regulator/tps65090.txt new file mode 100644 index 0000000..313a60b --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/tps65090.txt @@ -0,0 +1,122 @@ +TPS65090 regulators + +Required properties: +- compatible: "ti,tps65090" +- reg: I2C slave address +- interrupts: the interrupt outputs of the controller +- regulators: A node that houses a sub-node for each regulator within the + device. Each sub-node is identified using the node's name, with valid + values listed below. The content of each sub-node is defined by the + standard binding for regulators; see regulator.txt. + dcdc[1-3], fet[1-7] and ldo[1-2] respectively. +- vsys[1-3]-supply: The input supply for DCDC[1-3] respectively. +- infet[1-7]-supply: The input supply for FET[1-7] respectively. +- vsys-l[1-2]-supply: The input supply for LDO[1-2] respectively. + +Optional properties: +- ti,enable-ext-control: This is applicable for DCDC1, DCDC2 and DCDC3. + If DCDCs are externally controlled then this property should be there. +- "dcdc-ext-control-gpios: This is applicable for DCDC1, DCDC2 and DCDC3. + If DCDCs are externally controlled and if it is from GPIO then GPIO + number should be provided. If it is externally controlled and no GPIO + entry then driver will just configure this rails as external control + and will not provide any enable/disable APIs. + +Each regulator is defined using the standard binding for regulators. + +Example: + + tps65090@48 { + compatible = "ti,tps65090"; + reg = <0x48>; + interrupts = <0 88 0x4>; + + vsys1-supply = <&some_reg>; + vsys2-supply = <&some_reg>; + vsys3-supply = <&some_reg>; + infet1-supply = <&some_reg>; + infet2-supply = <&some_reg>; + infet3-supply = <&some_reg>; + infet4-supply = <&some_reg>; + infet5-supply = <&some_reg>; + infet6-supply = <&some_reg>; + infet7-supply = <&some_reg>; + vsys_l1-supply = <&some_reg>; + vsys_l2-supply = <&some_reg>; + + regulators { + dcdc1 { + regulator-name = "dcdc1"; + regulator-boot-on; + regulator-always-on; + ti,enable-ext-control; + dcdc-ext-control-gpios = <&gpio 10 0>; + }; + + dcdc2 { + regulator-name = "dcdc2"; + regulator-boot-on; + regulator-always-on; + }; + + dcdc3 { + regulator-name = "dcdc3"; + regulator-boot-on; + regulator-always-on; + }; + + fet1 { + regulator-name = "fet1"; + regulator-boot-on; + regulator-always-on; + }; + + fet2 { + regulator-name = "fet2"; + regulator-boot-on; + regulator-always-on; + }; + + fet3 { + regulator-name = "fet3"; + regulator-boot-on; + regulator-always-on; + }; + + fet4 { + regulator-name = "fet4"; + regulator-boot-on; + regulator-always-on; + }; + + fet5 { + regulator-name = "fet5"; + regulator-boot-on; + regulator-always-on; + }; + + fet6 { + regulator-name = "fet6"; + regulator-boot-on; + regulator-always-on; + }; + + fet7 { + regulator-name = "fet7"; + regulator-boot-on; + regulator-always-on; + }; + + ldo1 { + regulator-name = "ldo1"; + regulator-boot-on; + regulator-always-on; + }; + + ldo2 { + regulator-name = "ldo2"; + regulator-boot-on; + regulator-always-on; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/rtc/s3c-rtc.txt b/Documentation/devicetree/bindings/rtc/s3c-rtc.txt index 90ec45f..7ac7259 100644 --- a/Documentation/devicetree/bindings/rtc/s3c-rtc.txt +++ b/Documentation/devicetree/bindings/rtc/s3c-rtc.txt @@ -7,7 +7,7 @@ Required properties: - reg: physical base address of the controller and length of memory mapped region. - interrupts: Two interrupt numbers to the cpu should be specified. First - interrupt number is the rtc alarm interupt and second interrupt number + interrupt number is the rtc alarm interrupt and second interrupt number is the rtc tick interrupt. The number of cells representing a interrupt depends on the parent interrupt controller. diff --git a/Documentation/devicetree/bindings/serial/lantiq_asc.txt b/Documentation/devicetree/bindings/serial/lantiq_asc.txt new file mode 100644 index 0000000..5b78591 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/lantiq_asc.txt @@ -0,0 +1,16 @@ +Lantiq SoC ASC serial controller + +Required properties: +- compatible : Should be "lantiq,asc" +- reg : Address and length of the register set for the device +- interrupts: the 3 (tx rx err) interrupt numbers. The interrupt specifier + depends on the interrupt-parent interrupt controller. + +Example: + +asc1: serial@E100C00 { + compatible = "lantiq,asc"; + reg = <0xE100C00 0x400>; + interrupt-parent = <&icu0>; + interrupts = <112 113 114>; +}; diff --git a/Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.txt b/Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.txt new file mode 100644 index 0000000..392a449 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.txt @@ -0,0 +1,24 @@ +NVIDIA Tegra20/Tegra30 high speed (DMA based) UART controller driver. + +Required properties: +- compatible : should be "nvidia,tegra30-hsuart", "nvidia,tegra20-hsuart". +- reg: Should contain UART controller registers location and length. +- interrupts: Should contain UART controller interrupts. +- nvidia,dma-request-selector : The Tegra DMA controller's phandle and + request selector for this UART controller. + +Optional properties: +- nvidia,enable-modem-interrupt: Enable modem interrupts. Should be enable + only if all 8 lines of UART controller are pinmuxed. + +Example: + +serial@70006000 { + compatible = "nvidia,tegra30-hsuart", "nvidia,tegra20-hsuart"; + reg = <0x70006000 0x40>; + reg-shift = <2>; + interrupts = <0 36 0x04>; + nvidia,dma-request-selector = <&apbdma 8>; + nvidia,enable-modem-interrupt; + status = "disabled"; +}; diff --git a/Documentation/devicetree/bindings/sound/ak4642.txt b/Documentation/devicetree/bindings/sound/ak4642.txt new file mode 100644 index 0000000..623d4e7 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/ak4642.txt @@ -0,0 +1,17 @@ +AK4642 I2C transmitter + +This device supports I2C mode only. + +Required properties: + + - compatible : "asahi-kasei,ak4642" or "asahi-kasei,ak4643" or "asahi-kasei,ak4648" + - reg : The chip select number on the I2C bus + +Example: + +&i2c { + ak4648: ak4648@0x12 { + compatible = "asahi-kasei,ak4642"; + reg = <0x12>; + }; +}; diff --git a/Documentation/devicetree/bindings/sound/cs4271.txt b/Documentation/devicetree/bindings/sound/cs4271.txt index a850fb9..e2cd1d7 100644 --- a/Documentation/devicetree/bindings/sound/cs4271.txt +++ b/Documentation/devicetree/bindings/sound/cs4271.txt @@ -20,6 +20,18 @@ Optional properties: !RESET pin - cirrus,amuteb-eq-bmutec: When given, the Codec's AMUTEB=BMUTEC flag is enabled. + - cirrus,enable-soft-reset: + The CS4271 requires its LRCLK and MCLK to be stable before its RESET + line is de-asserted. That also means that clocks cannot be changed + without putting the chip back into hardware reset, which also requires + a complete re-initialization of all registers. + + One (undocumented) workaround is to assert and de-assert the PDN bit + in the MODE2 register. This workaround can be enabled with this DT + property. + + Note that this is not needed in case the clocks are stable + throughout the entire runtime of the codec. Examples: diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm9712.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm9712.txt new file mode 100644 index 0000000..be35d34 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm9712.txt @@ -0,0 +1,51 @@ +NVIDIA Tegra audio complex + +Required properties: +- compatible : "nvidia,tegra-audio-wm9712" +- nvidia,model : The user-visible name of this sound complex. +- nvidia,audio-routing : A list of the connections between audio components. + Each entry is a pair of strings, the first being the connection's sink, + the second being the connection's source. Valid names for sources and + sinks are the WM9712's pins, and the jacks on the board: + + WM9712 pins: + + * MONOOUT + * HPOUTL + * HPOUTR + * LOUT2 + * ROUT2 + * OUT3 + * LINEINL + * LINEINR + * PHONE + * PCBEEP + * MIC1 + * MIC2 + * Mic Bias + + Board connectors: + + * Headphone + * LineIn + * Mic + +- nvidia,ac97-controller : The phandle of the Tegra AC97 controller + + +Example: + +sound { + compatible = "nvidia,tegra-audio-wm9712-colibri_t20", + "nvidia,tegra-audio-wm9712"; + nvidia,model = "Toradex Colibri T20"; + + nvidia,audio-routing = + "Headphone", "HPOUTL", + "Headphone", "HPOUTR", + "LineIn", "LINEINL", + "LineIn", "LINEINR", + "Mic", "MIC1"; + + nvidia,ac97-controller = <&ac97>; +}; diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra20-ac97.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra20-ac97.txt new file mode 100644 index 0000000..c145497 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra20-ac97.txt @@ -0,0 +1,22 @@ +NVIDIA Tegra 20 AC97 controller + +Required properties: +- compatible : "nvidia,tegra20-ac97" +- reg : Should contain AC97 controller registers location and length +- interrupts : Should contain AC97 interrupt +- nvidia,dma-request-selector : The Tegra DMA controller's phandle and + request selector for the AC97 controller +- nvidia,codec-reset-gpio : The Tegra GPIO controller's phandle and the number + of the GPIO used to reset the external AC97 codec +- nvidia,codec-sync-gpio : The Tegra GPIO controller's phandle and the number + of the GPIO corresponding with the AC97 DAP _FS line +Example: + +ac97@70002000 { + compatible = "nvidia,tegra20-ac97"; + reg = <0x70002000 0x200>; + interrupts = <0 81 0x04>; + nvidia,dma-request-selector = <&apbdma 12>; + nvidia,codec-reset-gpio = <&gpio 170 0>; + nvidia,codec-sync-gpio = <&gpio 120 0>; +}; diff --git a/Documentation/devicetree/bindings/sound/omap-twl4030.txt b/Documentation/devicetree/bindings/sound/omap-twl4030.txt index 6fae51c..1ab6bc8 100644 --- a/Documentation/devicetree/bindings/sound/omap-twl4030.txt +++ b/Documentation/devicetree/bindings/sound/omap-twl4030.txt @@ -6,6 +6,52 @@ Required properties: - ti,mcbsp: phandle for the McBSP node - ti,codec: phandle for the twl4030 audio node +Optional properties: +- ti,mcbsp-voice: phandle for the McBSP node connected to the voice port of twl +- ti, jack-det-gpio: Jack detect GPIO +- ti,audio-routing: List of connections between audio components. + Each entry is a pair of strings, the first being the connection's sink, + the second being the connection's source. + If the routing is not provided all possible connection will be available + +Available audio endpoints for the audio-routing table: + +Board connectors: + * Headset Stereophone + * Earpiece Spk + * Handsfree Spk + * Ext Spk + * Main Mic + * Sub Mic + * Headset Mic + * Carkit Mic + * Digital0 Mic + * Digital1 Mic + * Line In + +twl4030 pins: + * HSOL + * HSOR + * EARPIECE + * HFL + * HFR + * PREDRIVEL + * PREDRIVER + * CARKITL + * CARKITR + * MAINMIC + * SUBMIC + * HSMIC + * DIGIMIC0 + * DIGIMIC1 + * CARKITMIC + * AUXL + * AUXR + + * Headset Mic Bias + * Mic Bias 1 /* Used for Main Mic or Digimic0 */ + * Mic Bias 2 /* Used for Sub Mic or Digimic1 */ + Example: sound { diff --git a/Documentation/devicetree/bindings/sound/renesas,fsi.txt b/Documentation/devicetree/bindings/sound/renesas,fsi.txt new file mode 100644 index 0000000..c5be003 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/renesas,fsi.txt @@ -0,0 +1,26 @@ +Renesas FSI + +Required properties: +- compatible : "renesas,sh_fsi2" or "renesas,sh_fsi" +- reg : Should contain the register physical address and length +- interrupts : Should contain FSI interrupt + +- fsia,spdif-connection : FSI is connected by S/PDFI +- fsia,stream-mode-support : FSI supports 16bit stream mode. +- fsia,use-internal-clock : FSI uses internal clock when master mode. + +- fsib,spdif-connection : same as fsia +- fsib,stream-mode-support : same as fsia +- fsib,use-internal-clock : same as fsia + +Example: + +sh_fsi2: sh_fsi2@0xec230000 { + compatible = "renesas,sh_fsi2"; + reg = <0xec230000 0x400>; + interrupts = <0 146 0x4>; + + fsia,spdif-connection; + fsia,stream-mode-support; + fsia,use-internal-clock; +}; diff --git a/Documentation/devicetree/bindings/sound/samsung,smdk-wm8994.txt b/Documentation/devicetree/bindings/sound/samsung,smdk-wm8994.txt new file mode 100644 index 0000000..4686646f --- /dev/null +++ b/Documentation/devicetree/bindings/sound/samsung,smdk-wm8994.txt @@ -0,0 +1,14 @@ +Samsung SMDK audio complex + +Required properties: +- compatible : "samsung,smdk-wm8994" +- samsung,i2s-controller: The phandle of the Samsung I2S0 controller +- samsung,audio-codec: The phandle of the WM8994 audio codec +Example: + +sound { + compatible = "samsung,smdk-wm8994"; + + samsung,i2s-controller = <&i2s0>; + samsung,audio-codec = <&wm8994>; +}; diff --git a/Documentation/devicetree/bindings/sound/samsung-i2s.txt b/Documentation/devicetree/bindings/sound/samsung-i2s.txt new file mode 100644 index 0000000..3070046 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/samsung-i2s.txt @@ -0,0 +1,63 @@ +* Samsung I2S controller + +Required SoC Specific Properties: + +- compatible : "samsung,i2s-v5" +- reg: physical base address of the controller and length of memory mapped + region. +- dmas: list of DMA controller phandle and DMA request line ordered pairs. +- dma-names: identifier string for each DMA request line in the dmas property. + These strings correspond 1:1 with the ordered pairs in dmas. + +Optional SoC Specific Properties: + +- samsung,supports-6ch: If the I2S Primary sound source has 5.1 Channel + support, this flag is enabled. +- samsung,supports-rstclr: This flag should be set if I2S software reset bit + control is required. When this flag is set I2S software reset bit will be + enabled or disabled based on need. +- samsung,supports-secdai:If I2S block has a secondary FIFO and internal DMA, + then this flag is enabled. +- samsung,idma-addr: Internal DMA register base address of the audio + sub system(used in secondary sound source). + +Required Board Specific Properties: + +- gpios: The gpio specifier for data out,data in, LRCLK, CDCLK and SCLK + interface lines. The format of the gpio specifier depends on the gpio + controller. + The syntax of samsung gpio specifier is + <[phandle of the gpio controller node] + [pin number within the gpio controller] + [mux function] + [flags and pull up/down] + [drive strength]> + +Example: + +- SoC Specific Portion: + +i2s@03830000 { + compatible = "samsung,i2s-v5"; + reg = <0x03830000 0x100>; + dmas = <&pdma0 10 + &pdma0 9 + &pdma0 8>; + dma-names = "tx", "rx", "tx-sec"; + samsung,supports-6ch; + samsung,supports-rstclr; + samsung,supports-secdai; + samsung,idma-addr = <0x03000000>; +}; + +- Board Specific Portion: + +i2s@03830000 { + gpios = <&gpz 0 2 0 0>, /* I2S_0_SCLK */ + <&gpz 1 2 0 0>, /* I2S_0_CDCLK */ + <&gpz 2 2 0 0>, /* I2S_0_LRCK */ + <&gpz 3 2 0 0>, /* I2S_0_SDI */ + <&gpz 4 2 0 0>, /* I2S_0_SDO[1] */ + <&gpz 5 2 0 0>, /* I2S_0_SDO[2] */ + <&gpz 6 2 0 0>; /* I2S_0_SDO[3] */ +}; diff --git a/Documentation/devicetree/bindings/sound/tlv320aic3x.txt b/Documentation/devicetree/bindings/sound/tlv320aic3x.txt index e7b98f4..f47c3f5 100644 --- a/Documentation/devicetree/bindings/sound/tlv320aic3x.txt +++ b/Documentation/devicetree/bindings/sound/tlv320aic3x.txt @@ -11,6 +11,12 @@ Optional properties: - gpio-reset - gpio pin number used for codec reset - ai3x-gpio-func - <array of 2 int> - AIC3X_GPIO1 & AIC3X_GPIO2 Functionality +- ai3x-micbias-vg - MicBias Voltage required. + 1 - MICBIAS output is powered to 2.0V, + 2 - MICBIAS output is powered to 2.5V, + 3 - MICBIAS output is connected to AVDD, + If this node is not mentioned or if the value is incorrect, then MicBias + is powered down. Example: diff --git a/Documentation/devicetree/bindings/sound/wm8962.txt b/Documentation/devicetree/bindings/sound/wm8962.txt new file mode 100644 index 0000000..dceb3b1 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/wm8962.txt @@ -0,0 +1,16 @@ +WM8962 audio CODEC + +This device supports I2C only. + +Required properties: + + - compatible : "wlf,wm8962" + + - reg : the I2C address of the device. + +Example: + +codec: wm8962@1a { + compatible = "wlf,wm8962"; + reg = <0x1a>; +}; diff --git a/Documentation/devicetree/bindings/spi/sh-msiof.txt b/Documentation/devicetree/bindings/spi/sh-msiof.txt new file mode 100644 index 0000000..e622210 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/sh-msiof.txt @@ -0,0 +1,12 @@ +Renesas MSIOF spi controller + +Required properties: +- compatible : "renesas,sh-msiof" for SuperH or + "renesas,sh-mobile-msiof" for SH Mobile series +- reg : Offset and length of the register set for the device +- interrupts : interrupt line used by MSIOF + +Optional properties: +- num-cs : total number of chip-selects +- renesas,tx-fifo-size : Overrides the default tx fifo size given in words +- renesas,rx-fifo-size : Overrides the default rx fifo size given in words diff --git a/Documentation/devicetree/bindings/staging/iio/adc/mxs-lradc.txt b/Documentation/devicetree/bindings/staging/iio/adc/mxs-lradc.txt index 801d58c..4688205 100644 --- a/Documentation/devicetree/bindings/staging/iio/adc/mxs-lradc.txt +++ b/Documentation/devicetree/bindings/staging/iio/adc/mxs-lradc.txt @@ -5,6 +5,12 @@ Required properties: - reg: Address and length of the register set for the device - interrupts: Should contain the LRADC interrupts +Optional properties: +- fsl,lradc-touchscreen-wires: Number of wires used to connect the touchscreen + to LRADC. Valid value is either 4 or 5. If this + property is not present, then the touchscreen is + disabled. + Examples: lradc@80050000 { diff --git a/Documentation/devicetree/bindings/thermal/dove-thermal.txt b/Documentation/devicetree/bindings/thermal/dove-thermal.txt new file mode 100644 index 0000000..6f47467 --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/dove-thermal.txt @@ -0,0 +1,18 @@ +* Dove Thermal + +This driver is for Dove SoCs which contain a thermal sensor. + +Required properties: +- compatible : "marvell,dove-thermal" +- reg : Address range of the thermal registers + +The reg properties should contain two ranges. The first is for the +three Thermal Manager registers, while the second range contains the +Thermal Diode Control Registers. + +Example: + + thermal@10078 { + compatible = "marvell,dove-thermal"; + reg = <0xd001c 0x0c>, <0xd005c 0x08>; + }; diff --git a/Documentation/devicetree/bindings/thermal/kirkwood-thermal.txt b/Documentation/devicetree/bindings/thermal/kirkwood-thermal.txt new file mode 100644 index 0000000..8c0f5eb --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/kirkwood-thermal.txt @@ -0,0 +1,15 @@ +* Kirkwood Thermal + +This version is for Kirkwood 88F8262 & 88F6283 SoCs. Other kirkwoods +don't contain a thermal sensor. + +Required properties: +- compatible : "marvell,kirkwood-thermal" +- reg : Address range of the thermal registers + +Example: + + thermal@10078 { + compatible = "marvell,kirkwood-thermal"; + reg = <0x10078 0x4>; + }; diff --git a/Documentation/devicetree/bindings/thermal/rcar-thermal.txt b/Documentation/devicetree/bindings/thermal/rcar-thermal.txt new file mode 100644 index 0000000..28ef498 --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/rcar-thermal.txt @@ -0,0 +1,29 @@ +* Renesas R-Car Thermal + +Required properties: +- compatible : "renesas,rcar-thermal" +- reg : Address range of the thermal registers. + The 1st reg will be recognized as common register + if it has "interrupts". + +Option properties: + +- interrupts : use interrupt + +Example (non interrupt support): + +thermal@e61f0100 { + compatible = "renesas,rcar-thermal"; + reg = <0xe61f0100 0x38>; +}; + +Example (interrupt support): + +thermal@e61f0000 { + compatible = "renesas,rcar-thermal"; + reg = <0xe61f0000 0x14 + 0xe61f0100 0x38 + 0xe61f0200 0x38 + 0xe61f0300 0x38>; + interrupts = <0 69 4>; +}; diff --git a/Documentation/devicetree/bindings/arm/armada-370-xp-timer.txt b/Documentation/devicetree/bindings/timer/marvell,armada-370-xp-timer.txt index 6483011..3638112 100644 --- a/Documentation/devicetree/bindings/arm/armada-370-xp-timer.txt +++ b/Documentation/devicetree/bindings/timer/marvell,armada-370-xp-timer.txt @@ -1,10 +1,13 @@ -Marvell Armada 370 and Armada XP Global Timers ----------------------------------------------- +Marvell Armada 370 and Armada XP Timers +--------------------------------------- Required properties: - compatible: Should be "marvell,armada-370-xp-timer" -- interrupts: Should contain the list of Global Timer interrupts -- reg: Should contain the base address of the Global Timer registers +- interrupts: Should contain the list of Global Timer interrupts and + then local timer interrupts +- reg: Should contain location and length for timers register. First + pair for the Global Timer registers, second pair for the + local/private timers. - clocks: clock driving the timer hardware Optional properties: diff --git a/Documentation/devicetree/bindings/tty/serial/arc-uart.txt b/Documentation/devicetree/bindings/tty/serial/arc-uart.txt new file mode 100644 index 0000000..5cae2eb --- /dev/null +++ b/Documentation/devicetree/bindings/tty/serial/arc-uart.txt @@ -0,0 +1,26 @@ +* Synopsys ARC UART : Non standard UART used in some of the ARC FPGA boards + +Required properties: +- compatible : "snps,arc-uart" +- reg : offset and length of the register set for the device. +- interrupts : device interrupt +- clock-frequency : the input clock frequency for the UART +- current-speed : baud rate for UART + +e.g. + +arcuart0: serial@c0fc1000 { + compatible = "snps,arc-uart"; + reg = <0xc0fc1000 0x100>; + interrupts = <5>; + clock-frequency = <80000000>; + current-speed = <115200>; + status = "okay"; +}; + +Note: Each port should have an alias correctly numbered in "aliases" node. + +e.g. +aliases { + serial0 = &arcuart0; +}; diff --git a/Documentation/devicetree/bindings/tty/serial/efm32-uart.txt b/Documentation/devicetree/bindings/tty/serial/efm32-uart.txt index 6588b69..8e080b8 100644 --- a/Documentation/devicetree/bindings/tty/serial/efm32-uart.txt +++ b/Documentation/devicetree/bindings/tty/serial/efm32-uart.txt @@ -5,10 +5,16 @@ Required properties: - reg : Address and length of the register set - interrupts : Should contain uart interrupt +Optional properties: +- location : Decides the location of the USART I/O pins. + Allowed range : [0 .. 5] + Default: 0 + Example: uart@0x4000c400 { compatible = "efm32,uart"; reg = <0x4000c400 0x400>; interrupts = <15>; + location = <0>; }; diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt new file mode 100644 index 0000000..7a95c65 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/dwc3.txt @@ -0,0 +1,22 @@ +synopsys DWC3 CORE + +DWC3- USB3 CONTROLLER + +Required properties: + - compatible: must be "synopsys,dwc3" + - reg : Address and length of the register set for the device + - interrupts: Interrupts used by the dwc3 controller. + - usb-phy : array of phandle for the PHY device + +Optional properties: + - tx-fifo-resize: determines if the FIFO *has* to be reallocated. + +This is usually a subnode to DWC3 glue to which it is connected. + +dwc3@4a030000 { + compatible = "synopsys,dwc3"; + reg = <0x4a030000 0xcfff>; + interrupts = <0 92 4> + usb-phy = <&usb2_phy>, <&usb3,phy>; + tx-fifo-resize; +}; diff --git a/Documentation/devicetree/bindings/usb/nvidia,tegra20-ehci.txt b/Documentation/devicetree/bindings/usb/nvidia,tegra20-ehci.txt index e9b005d..34c9528 100644 --- a/Documentation/devicetree/bindings/usb/nvidia,tegra20-ehci.txt +++ b/Documentation/devicetree/bindings/usb/nvidia,tegra20-ehci.txt @@ -11,6 +11,7 @@ Required properties : - phy_type : Should be one of "ulpi" or "utmi". - nvidia,vbus-gpio : If present, specifies a gpio that needs to be activated for the bus to be powered. + - nvidia,phy : phandle of the PHY instance, the controller is connected to. Required properties for phy_type == ulpi: - nvidia,phy-reset-gpio : The GPIO used to reset the PHY. @@ -27,3 +28,5 @@ Optional properties: registers are accessed through the APB_MISC base address instead of the USB controller. Since this is a legacy issue it probably does not warrant a compatible string of its own. + - nvidia,needs-double-reset : boolean is to be set for some of the Tegra2 + USB ports, which need reset twice due to hardware issues. diff --git a/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt b/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt new file mode 100644 index 0000000..6bdaba2 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt @@ -0,0 +1,17 @@ +Tegra SOC USB PHY + +The device node for Tegra SOC USB PHY: + +Required properties : + - compatible : Should be "nvidia,tegra20-usb-phy". + - reg : Address and length of the register set for the USB PHY interface. + - phy_type : Should be one of "ulpi" or "utmi". + +Required properties for phy_type == ulpi: + - nvidia,phy-reset-gpio : The GPIO used to reset the PHY. + +Optional properties: + - nvidia,has-legacy-mode : boolean indicates whether this controller can + operate in legacy mode (as APX 2500 / 2600). In legacy mode some + registers are accessed through the APB_MISC base address instead of + the USB controller.
\ No newline at end of file diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt index 29a043e..1ef0ce7 100644 --- a/Documentation/devicetree/bindings/usb/omap-usb.txt +++ b/Documentation/devicetree/bindings/usb/omap-usb.txt @@ -1,8 +1,11 @@ -OMAP GLUE +OMAP GLUE AND OTHER OMAP SPECIFIC COMPONENTS OMAP MUSB GLUE - compatible : Should be "ti,omap4-musb" or "ti,omap3-musb" - ti,hwmods : must be "usb_otg_hs" + - ti,has-mailbox : to specify that omap uses an external mailbox + (in control module) to communicate with the musb core during device connect + and disconnect. - multipoint : Should be "1" indicating the musb controller supports multipoint. This is a MUSB configuration-specific setting. - num_eps : Specifies the number of endpoints. This is also a @@ -16,13 +19,19 @@ OMAP MUSB GLUE - power : Should be "50". This signifies the controller can supply upto 100mA when operating in host mode. +Optional properties: + - ctrl-module : phandle of the control module this glue uses to write to + mailbox + SOC specific device node entry usb_otg_hs: usb_otg_hs@4a0ab000 { compatible = "ti,omap4-musb"; ti,hwmods = "usb_otg_hs"; + ti,has-mailbox; multipoint = <1>; num_eps = <16>; ram_bits = <12>; + ctrl-module = <&omap_control_usb>; }; Board specific device node entry @@ -31,3 +40,26 @@ Board specific device node entry mode = <3>; power = <50>; }; + +OMAP CONTROL USB + +Required properties: + - compatible: Should be "ti,omap-control-usb" + - reg : Address and length of the register set for the device. It contains + the address of "control_dev_conf" and "otghs_control" or "phy_power_usb" + depending upon omap4 or omap5. + - reg-names: The names of the register addresses corresponding to the registers + filled in "reg". + - ti,type: This is used to differentiate whether the control module has + usb mailbox or usb3 phy power. omap4 has usb mailbox in control module to + notify events to the musb core and omap5 has usb3 phy power register to + power on usb3 phy. Should be "1" if it has mailbox and "2" if it has usb3 + phy power. + +omap_control_usb: omap-control-usb@4a002300 { + compatible = "ti,omap-control-usb"; + reg = <0x4a002300 0x4>, + <0x4a00233c 0x4>; + reg-names = "control_dev_conf", "otghs_control"; + ti,type = <1>; +}; diff --git a/Documentation/devicetree/bindings/usb/samsung-usbphy.txt b/Documentation/devicetree/bindings/usb/samsung-usbphy.txt new file mode 100644 index 0000000..0331949 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/samsung-usbphy.txt @@ -0,0 +1,55 @@ +* Samsung's usb phy transceiver + +The Samsung's phy transceiver is used for controlling usb phy for +s3c-hsotg as well as ehci-s5p and ohci-exynos usb controllers +across Samsung SOCs. +TODO: Adding the PHY binding with controller(s) according to the under +developement generic PHY driver. + +Required properties: + +Exynos4210: +- compatible : should be "samsung,exynos4210-usbphy" +- reg : base physical address of the phy registers and length of memory mapped + region. + +Exynos5250: +- compatible : should be "samsung,exynos5250-usbphy" +- reg : base physical address of the phy registers and length of memory mapped + region. + +Optional properties: +- #address-cells: should be '1' when usbphy node has a child node with 'reg' + property. +- #size-cells: should be '1' when usbphy node has a child node with 'reg' + property. +- ranges: allows valid translation between child's address space and parent's + address space. + +- The child node 'usbphy-sys' to the node 'usbphy' is for the system controller + interface for usb-phy. It should provide the following information required by + usb-phy controller to control phy. + - reg : base physical address of PHY_CONTROL registers. + The size of this register is the total sum of size of all PHY_CONTROL + registers that the SoC has. For example, the size will be + '0x4' in case we have only one PHY_CONTROL register (e.g. + OTHERS register in S3C64XX or USB_PHY_CONTROL register in S5PV210) + and, '0x8' in case we have two PHY_CONTROL registers (e.g. + USBDEVICE_PHY_CONTROL and USBHOST_PHY_CONTROL registers in exynos4x). + and so on. + +Example: + - Exynos4210 + + usbphy@125B0000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "samsung,exynos4210-usbphy"; + reg = <0x125B0000 0x100>; + ranges; + + usbphy-sys { + /* USB device and host PHY_CONTROL registers */ + reg = <0x10020704 0x8>; + }; + }; diff --git a/Documentation/devicetree/bindings/usb/usb-phy.txt b/Documentation/devicetree/bindings/usb/usb-phy.txt index 80d4148..61496f5 100644 --- a/Documentation/devicetree/bindings/usb/usb-phy.txt +++ b/Documentation/devicetree/bindings/usb/usb-phy.txt @@ -4,14 +4,39 @@ OMAP USB2 PHY Required properties: - compatible: Should be "ti,omap-usb2" - - reg : Address and length of the register set for the device. Also -add the address of control module dev conf register until a driver for -control module is added + - reg : Address and length of the register set for the device. + +Optional properties: + - ctrl-module : phandle of the control module used by PHY driver to power on + the PHY. This is usually a subnode of ocp2scp to which it is connected. usb2phy@4a0ad080 { compatible = "ti,omap-usb2"; - reg = <0x4a0ad080 0x58>, - <0x4a002300 0x4>; + reg = <0x4a0ad080 0x58>; + ctrl-module = <&omap_control_usb>; +}; + +OMAP USB3 PHY + +Required properties: + - compatible: Should be "ti,omap-usb3" + - reg : Address and length of the register set for the device. + - reg-names: The names of the register addresses corresponding to the registers + filled in "reg". + +Optional properties: + - ctrl-module : phandle of the control module used by PHY driver to power on + the PHY. + +This is usually a subnode of ocp2scp to which it is connected. + +usb3phy@4a084400 { + compatible = "ti,omap-usb3"; + reg = <0x4a084400 0x80>, + <0x4a084800 0x64>, + <0x4a084c00 0x40>; + reg-names = "phy_rx", "phy_tx", "pll_ctrl"; + ctrl-module = <&omap_control_usb>; }; diff --git a/Documentation/devicetree/bindings/usb/usb3503.txt b/Documentation/devicetree/bindings/usb/usb3503.txt new file mode 100644 index 0000000..6813a71 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/usb3503.txt @@ -0,0 +1,20 @@ +SMSC USB3503 High-Speed Hub Controller + +Required properties: +- compatible: Should be "smsc,usb3503". +- reg: Specifies the i2c slave address, it should be 0x08. +- connect-gpios: Should specify GPIO for connect. +- intn-gpios: Should specify GPIO for interrupt. +- reset-gpios: Should specify GPIO for reset. +- initial-mode: Should specify initial mode. + (1 for HUB mode, 2 for STANDBY mode) + +Examples: + usb3503@08 { + compatible = "smsc,usb3503"; + reg = <0x08>; + connect-gpios = <&gpx3 0 1>; + intn-gpios = <&gpx3 4 1>; + reset-gpios = <&gpx3 5 1>; + initial-mode = <1>; + }; diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 902b1b1..19e1ef73 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -14,6 +14,7 @@ bosch Bosch Sensortec GmbH brcm Broadcom Corporation cavium Cavium, Inc. chrp Common Hardware Reference Platform +cirrus Cirrus Logic, Inc. cortina Cortina Systems, Inc. dallas Maxim Integrated Products (formerly Dallas Semiconductor) denx Denx Software Engineering @@ -42,6 +43,7 @@ powervr PowerVR (deprecated, use img) qcom Qualcomm, Inc. ramtron Ramtron International realtek Realtek Semiconductor Corp. +renesas Renesas Electronics Corporation samsung Samsung Semiconductor sbs Smart Battery System schindler Schindler @@ -50,8 +52,10 @@ simtek sirf SiRF Technology, Inc. snps Synopsys, Inc. st STMicroelectronics +ste ST-Ericsson stericsson ST-Ericsson ti Texas Instruments +toshiba Toshiba Corporation via VIA Technologies, Inc. wlf Wolfson Microelectronics wm Wondermedia Technologies, Inc. diff --git a/Documentation/devicetree/bindings/video/backlight/max8925-backlight.txt b/Documentation/devicetree/bindings/video/backlight/max8925-backlight.txt new file mode 100644 index 0000000..b4cffda --- /dev/null +++ b/Documentation/devicetree/bindings/video/backlight/max8925-backlight.txt @@ -0,0 +1,10 @@ +88pm860x-backlight bindings + +Optional properties: + - maxim,max8925-dual-string: whether support dual string + +Example: + + backlights { + maxim,max8925-dual-string = <0>; + }; diff --git a/Documentation/devicetree/bindings/video/display-timing.txt b/Documentation/devicetree/bindings/video/display-timing.txt new file mode 100644 index 0000000..1500385 --- /dev/null +++ b/Documentation/devicetree/bindings/video/display-timing.txt @@ -0,0 +1,109 @@ +display-timing bindings +======================= + +display-timings node +-------------------- + +required properties: + - none + +optional properties: + - native-mode: The native mode for the display, in case multiple modes are + provided. When omitted, assume the first node is the native. + +timing subnode +-------------- + +required properties: + - hactive, vactive: display resolution + - hfront-porch, hback-porch, hsync-len: horizontal display timing parameters + in pixels + vfront-porch, vback-porch, vsync-len: vertical display timing parameters in + lines + - clock-frequency: display clock in Hz + +optional properties: + - hsync-active: hsync pulse is active low/high/ignored + - vsync-active: vsync pulse is active low/high/ignored + - de-active: data-enable pulse is active low/high/ignored + - pixelclk-active: with + - active high = drive pixel data on rising edge/ + sample data on falling edge + - active low = drive pixel data on falling edge/ + sample data on rising edge + - ignored = ignored + - interlaced (bool): boolean to enable interlaced mode + - doublescan (bool): boolean to enable doublescan mode + +All the optional properties that are not bool follow the following logic: + <1>: high active + <0>: low active + omitted: not used on hardware + +There are different ways of describing the capabilities of a display. The +devicetree representation corresponds to the one commonly found in datasheets +for displays. If a display supports multiple signal timings, the native-mode +can be specified. + +The parameters are defined as: + + +----------+-------------------------------------+----------+-------+ + | | ↑ | | | + | | |vback_porch | | | + | | ↓ | | | + +----------#######################################----------+-------+ + | # ↑ # | | + | # | # | | + | hback # | # hfront | hsync | + | porch # | hactive # porch | len | + |<-------->#<-------+--------------------------->#<-------->|<----->| + | # | # | | + | # |vactive # | | + | # | # | | + | # ↓ # | | + +----------#######################################----------+-------+ + | | ↑ | | | + | | |vfront_porch | | | + | | ↓ | | | + +----------+-------------------------------------+----------+-------+ + | | ↑ | | | + | | |vsync_len | | | + | | ↓ | | | + +----------+-------------------------------------+----------+-------+ + +Example: + + display-timings { + native-mode = <&timing0>; + timing0: 1080p24 { + /* 1920x1080p24 */ + clock-frequency = <52000000>; + hactive = <1920>; + vactive = <1080>; + hfront-porch = <25>; + hback-porch = <25>; + hsync-len = <25>; + vback-porch = <2>; + vfront-porch = <2>; + vsync-len = <2>; + hsync-active = <1>; + }; + }; + +Every required property also supports the use of ranges, so the commonly used +datasheet description with minimum, typical and maximum values can be used. + +Example: + + timing1: timing { + /* 1920x1080p24 */ + clock-frequency = <148500000>; + hactive = <1920>; + vactive = <1080>; + hsync-len = <0 44 60>; + hfront-porch = <80 88 95>; + hback-porch = <100 148 160>; + vfront-porch = <0 4 6>; + vback-porch = <0 36 50>; + vsync-len = <0 5 6>; + }; diff --git a/Documentation/devicetree/bindings/w1/fsl-imx-owire.txt b/Documentation/devicetree/bindings/w1/fsl-imx-owire.txt new file mode 100644 index 0000000..ecf42c0 --- /dev/null +++ b/Documentation/devicetree/bindings/w1/fsl-imx-owire.txt @@ -0,0 +1,19 @@ +* Freescale i.MX One wire bus master controller + +Required properties: +- compatible : should be "fsl,imx21-owire" +- reg : Address and length of the register set for the device + +Optional properties: +- clocks : phandle of clock that supplies the module (required if platform + clock bindings use device tree) + +Example: + +- From imx53.dtsi: +owire: owire@63fa4000 { + compatible = "fsl,imx53-owire", "fsl,imx21-owire"; + reg = <0x63fa4000 0x4000>; + clocks = <&clks 159>; + status = "disabled"; +}; diff --git a/Documentation/devicetree/bindings/watchdog/atmel-at91rm9200-wdt.txt b/Documentation/devicetree/bindings/watchdog/atmel-at91rm9200-wdt.txt new file mode 100644 index 0000000..d4d86cf --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/atmel-at91rm9200-wdt.txt @@ -0,0 +1,9 @@ +Atmel AT91RM9200 System Timer Watchdog + +Required properties: +- compatible: must be "atmel,at91sam9260-wdt". + +Example: + watchdog@fffffd00 { + compatible = "atmel,at91rm9200-wdt"; + }; diff --git a/Documentation/devicetree/bindings/watchdog/atmel-wdt.txt b/Documentation/devicetree/bindings/watchdog/atmel-wdt.txt index 2957ebb..fcdd48f 100644 --- a/Documentation/devicetree/bindings/watchdog/atmel-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/atmel-wdt.txt @@ -7,9 +7,13 @@ Required properties: - reg: physical base address of the controller and length of memory mapped region. +Optional properties: +- timeout-sec: contains the watchdog timeout in seconds. + Example: watchdog@fffffd40 { compatible = "atmel,at91sam9260-wdt"; reg = <0xfffffd40 0x10>; + timeout-sec = <10>; }; diff --git a/Documentation/devicetree/bindings/watchdog/marvel.txt b/Documentation/devicetree/bindings/watchdog/marvel.txt index 0b2503a..5dc8d30 100644 --- a/Documentation/devicetree/bindings/watchdog/marvel.txt +++ b/Documentation/devicetree/bindings/watchdog/marvel.txt @@ -5,10 +5,15 @@ Required Properties: - Compatibility : "marvell,orion-wdt" - reg : Address of the timer registers +Optional properties: + +- timeout-sec : Contains the watchdog timeout in seconds + Example: wdt@20300 { compatible = "marvell,orion-wdt"; reg = <0x20300 0x28>; + timeout-sec = <10>; status = "okay"; }; diff --git a/Documentation/devicetree/bindings/watchdog/pnx4008-wdt.txt b/Documentation/devicetree/bindings/watchdog/pnx4008-wdt.txt index 7c7f688..556d06c 100644 --- a/Documentation/devicetree/bindings/watchdog/pnx4008-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/pnx4008-wdt.txt @@ -5,9 +5,13 @@ Required properties: - reg: physical base address of the controller and length of memory mapped region. +Optional properties: +- timeout-sec: contains the watchdog timeout in seconds. + Example: watchdog@4003C000 { compatible = "nxp,pnx4008-wdt"; reg = <0x4003C000 0x1000>; + timeout-sec = <10>; }; diff --git a/Documentation/devicetree/bindings/watchdog/qca-ar7130-wdt.txt b/Documentation/devicetree/bindings/watchdog/qca-ar7130-wdt.txt new file mode 100644 index 0000000..7a89e5f --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/qca-ar7130-wdt.txt @@ -0,0 +1,13 @@ +* Qualcomm Atheros AR7130 Watchdog Timer (WDT) Controller + +Required properties: +- compatible: must be "qca,ar7130-wdt" +- reg: physical base address of the controller and length of memory mapped + region. + +Example: + +wdt@18060008 { + compatible = "qca,ar9330-wdt", "qca,ar7130-wdt"; + reg = <0x18060008 0x8>; +}; diff --git a/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt b/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt index 79ead82..2aa486c 100644 --- a/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt @@ -2,10 +2,13 @@ The Samsung's Watchdog controller is used for resuming system operation after a preset amount of time during which the WDT reset event has not -occured. +occurred. Required properties: - compatible : should be "samsung,s3c2410-wdt" - reg : base physical address of the controller and length of memory mapped region. - interrupts : interrupt number to the cpu. + +Optional properties: +- timeout-sec : contains the watchdog timeout in seconds. diff --git a/Documentation/devicetree/booting-without-of.txt b/Documentation/devicetree/booting-without-of.txt index d4d6675..b2fb2f5 100644 --- a/Documentation/devicetree/booting-without-of.txt +++ b/Documentation/devicetree/booting-without-of.txt @@ -1228,7 +1228,7 @@ hierarchy and routing of interrupts in the hardware. The interrupt tree model is fully described in the document "Open Firmware Recommended Practice: Interrupt Mapping Version 0.9". The document is available at: -<http://playground.sun.com/1275/practice>. +<http://www.openfirmware.org/ofwg/practice/> 1) interrupts property ---------------------- |