diff options
Diffstat (limited to 'Documentation/devicetree')
3 files changed, 103 insertions, 1 deletions
diff --git a/Documentation/devicetree/bindings/bus/uniphier-system-bus.txt b/Documentation/devicetree/bindings/bus/uniphier-system-bus.txt new file mode 100644 index 0000000..68ef80a --- /dev/null +++ b/Documentation/devicetree/bindings/bus/uniphier-system-bus.txt @@ -0,0 +1,66 @@ +UniPhier System Bus + +The UniPhier System Bus is an external bus that connects on-board devices to +the UniPhier SoC. It is a simple (semi-)parallel bus with address, data, and +some control signals. It supports up to 8 banks (chip selects). + +Before any access to the bus, the bus controller must be configured; the bus +controller registers provide the control for the translation from the offset +within each bank to the CPU-viewed address. The needed setup includes the base +address, the size of each bank. Optionally, some timing parameters can be +optimized for faster bus access. + +Required properties: +- compatible: should be "socionext,uniphier-system-bus". +- reg: offset and length of the register set for the bus controller device. +- #address-cells: should be 2. The first cell is the bank number (chip select). + The second cell is the address offset within the bank. +- #size-cells: should be 1. +- ranges: should provide a proper address translation from the System Bus to + the parent bus. + +Note: +The address region(s) that can be assigned for the System Bus is implementation +defined. Some SoCs can use 0x00000000-0x0fffffff and 0x40000000-0x4fffffff, +while other SoCs can only use 0x40000000-0x4fffffff. There might be additional +limitations depending on SoCs and the boot mode. The address translation is +arbitrary as long as the banks are assigned in the supported address space with +the required alignment and they do not overlap one another. +For example, it is possible to map: + bank 0 to 0x42000000-0x43ffffff, bank 5 to 0x46000000-0x46ffffff +It is also possible to map: + bank 0 to 0x48000000-0x49ffffff, bank 5 to 0x44000000-0x44ffffff +There is no reason to stick to a particular translation mapping, but the +"ranges" property should provide a "reasonable" default that is known to work. +The software should initialize the bus controller according to it. + +Example: + + system-bus { + compatible = "socionext,uniphier-system-bus"; + reg = <0x58c00000 0x400>; + #address-cells = <2>; + #size-cells = <1>; + ranges = <1 0x00000000 0x42000000 0x02000000 + 5 0x00000000 0x46000000 0x01000000>; + + ethernet@1,01f00000 { + compatible = "smsc,lan9115"; + reg = <1 0x01f00000 0x1000>; + interrupts = <0 48 4> + phy-mode = "mii"; + }; + + uart@5,00200000 { + compatible = "ns16550a"; + reg = <5 0x00200000 0x20>; + interrupts = <0 49 4> + clock-frequency = <12288000>; + }; + }; + +In this example, + - the Ethernet device is connected at the offset 0x01f00000 of CS1 and + mapped to 0x43f00000 of the parent bus. + - the UART device is connected at the offset 0x00200000 of CS5 and + mapped to 0x46200000 of the parent bus. diff --git a/Documentation/devicetree/bindings/reset/hisilicon,hi6220-reset.txt b/Documentation/devicetree/bindings/reset/hisilicon,hi6220-reset.txt new file mode 100644 index 0000000..e0b185a --- /dev/null +++ b/Documentation/devicetree/bindings/reset/hisilicon,hi6220-reset.txt @@ -0,0 +1,34 @@ +Hisilicon System Reset Controller +====================================== + +Please also refer to reset.txt in this directory for common reset +controller binding usage. + +The reset controller registers are part of the system-ctl block on +hi6220 SoC. + +Required properties: +- compatible: may be "hisilicon,hi6220-sysctrl" +- reg: should be register base and length as documented in the + datasheet +- #reset-cells: 1, see below + +Example: +sys_ctrl: sys_ctrl@f7030000 { + compatible = "hisilicon,hi6220-sysctrl", "syscon"; + reg = <0x0 0xf7030000 0x0 0x2000>; + #clock-cells = <1>; + #reset-cells = <1>; +}; + +Specifying reset lines connected to IP modules +============================================== +example: + + uart1: serial@..... { + ... + resets = <&sys_ctrl PERIPH_RSTEN3_UART1>; + ... + }; + +The index could be found in <dt-bindings/reset/hisi,hi6220-resets.h>. diff --git a/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt b/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt index b38200d..0dfa60d 100644 --- a/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt @@ -1,7 +1,9 @@ * Temperature Sensor ADC (TSADC) on rockchip SoCs Required properties: -- compatible : "rockchip,rk3288-tsadc" +- compatible : should be "rockchip,<name>-tsadc" + "rockchip,rk3288-tsadc": found on RK3288 SoCs + "rockchip,rk3368-tsadc": found on RK3368 SoCs - reg : physical base address of the controller and length of memory mapped region. - interrupts : The interrupt number to the cpu. The interrupt specifier format |
