diff options
Diffstat (limited to 'Documentation/devicetree')
4 files changed, 173 insertions, 8 deletions
diff --git a/Documentation/devicetree/bindings/cpufreq/brcm,stb-avs-cpu-freq.txt b/Documentation/devicetree/bindings/cpufreq/brcm,stb-avs-cpu-freq.txt new file mode 100644 index 0000000..af23857 --- /dev/null +++ b/Documentation/devicetree/bindings/cpufreq/brcm,stb-avs-cpu-freq.txt @@ -0,0 +1,78 @@ +Broadcom AVS mail box and interrupt register bindings +===================================================== + +A total of three DT nodes are required. One node (brcm,avs-cpu-data-mem) +references the mailbox register used to communicate with the AVS CPU[1]. The +second node (brcm,avs-cpu-l2-intr) is required to trigger an interrupt on +the AVS CPU. The interrupt tells the AVS CPU that it needs to process a +command sent to it by a driver. Interrupting the AVS CPU is mandatory for +commands to be processed. + +The interface also requires a reference to the AVS host interrupt controller, +so a driver can react to interrupts generated by the AVS CPU whenever a command +has been processed. See [2] for more information on the brcm,l2-intc node. + +[1] The AVS CPU is an independent co-processor that runs proprietary +firmware. On some SoCs, this firmware supports DFS and DVFS in addition to +Adaptive Voltage Scaling. + +[2] Documentation/devicetree/bindings/interrupt-controller/brcm,l2-intc.txt + + +Node brcm,avs-cpu-data-mem +-------------------------- + +Required properties: +- compatible: must include: brcm,avs-cpu-data-mem and + should include: one of brcm,bcm7271-avs-cpu-data-mem or + brcm,bcm7268-avs-cpu-data-mem +- reg: Specifies base physical address and size of the registers. +- interrupts: The interrupt that the AVS CPU will use to interrupt the host + when a command completed. +- interrupt-parent: The interrupt controller the above interrupt is routed + through. +- interrupt-names: The name of the interrupt used to interrupt the host. + +Optional properties: +- None + +Node brcm,avs-cpu-l2-intr +------------------------- + +Required properties: +- compatible: must include: brcm,avs-cpu-l2-intr and + should include: one of brcm,bcm7271-avs-cpu-l2-intr or + brcm,bcm7268-avs-cpu-l2-intr +- reg: Specifies base physical address and size of the registers. + +Optional properties: +- None + + +Example +======= + + avs_host_l2_intc: interrupt-controller@f04d1200 { + #interrupt-cells = <1>; + compatible = "brcm,l2-intc"; + interrupt-parent = <&intc>; + reg = <0xf04d1200 0x48>; + interrupt-controller; + interrupts = <0x0 0x19 0x0>; + interrupt-names = "avs"; + }; + + avs-cpu-data-mem@f04c4000 { + compatible = "brcm,bcm7271-avs-cpu-data-mem", + "brcm,avs-cpu-data-mem"; + reg = <0xf04c4000 0x60>; + interrupts = <0x1a>; + interrupt-parent = <&avs_host_l2_intc>; + interrupt-names = "sw_intr"; + }; + + avs-cpu-l2-intr@f04d1100 { + compatible = "brcm,bcm7271-avs-cpu-l2-intr", + "brcm,avs-cpu-l2-intr"; + reg = <0xf04d1100 0x10>; + }; diff --git a/Documentation/devicetree/bindings/opp/opp.txt b/Documentation/devicetree/bindings/opp/opp.txt index ee91cbd..9f5ca44 100644 --- a/Documentation/devicetree/bindings/opp/opp.txt +++ b/Documentation/devicetree/bindings/opp/opp.txt @@ -86,8 +86,14 @@ Optional properties: Single entry is for target voltage and three entries are for <target min max> voltages. - Entries for multiple regulators must be present in the same order as - regulators are specified in device's DT node. + Entries for multiple regulators shall be provided in the same field separated + by angular brackets <>. The OPP binding doesn't provide any provisions to + relate the values to their power supplies or the order in which the supplies + need to be configured and that is left for the implementation specific + binding. + + Entries for all regulators shall be of the same size, i.e. either all use a + single value or triplets. - opp-microvolt-<name>: Named opp-microvolt property. This is exactly similar to the above opp-microvolt property, but allows multiple voltage ranges to be @@ -104,10 +110,13 @@ Optional properties: Should only be set if opp-microvolt is set for the OPP. - Entries for multiple regulators must be present in the same order as - regulators are specified in device's DT node. If this property isn't required - for few regulators, then this should be marked as zero for them. If it isn't - required for any regulator, then this property need not be present. + Entries for multiple regulators shall be provided in the same field separated + by angular brackets <>. If current values aren't required for a regulator, + then it shall be filled with 0. If current values aren't required for any of + the regulators, then this field is not required. The OPP binding doesn't + provide any provisions to relate the values to their power supplies or the + order in which the supplies need to be configured and that is left for the + implementation specific binding. - opp-microamp-<name>: Named opp-microamp property. Similar to opp-microvolt-<name> property, but for microamp instead. @@ -386,10 +395,12 @@ Example 4: Handling multiple regulators / { cpus { cpu@0 { - compatible = "arm,cortex-a7"; + compatible = "vendor,cpu-type"; ... - cpu-supply = <&cpu_supply0>, <&cpu_supply1>, <&cpu_supply2>; + vcc0-supply = <&cpu_supply0>; + vcc1-supply = <&cpu_supply1>; + vcc2-supply = <&cpu_supply2>; operating-points-v2 = <&cpu0_opp_table>; }; }; diff --git a/Documentation/devicetree/bindings/power/domain-idle-state.txt b/Documentation/devicetree/bindings/power/domain-idle-state.txt new file mode 100644 index 0000000..eefc7ed --- /dev/null +++ b/Documentation/devicetree/bindings/power/domain-idle-state.txt @@ -0,0 +1,33 @@ +PM Domain Idle State Node: + +A domain idle state node represents the state parameters that will be used to +select the state when there are no active components in the domain. + +The state node has the following parameters - + +- compatible: + Usage: Required + Value type: <string> + Definition: Must be "domain-idle-state". + +- entry-latency-us + Usage: Required + Value type: <prop-encoded-array> + Definition: u32 value representing worst case latency in + microseconds required to enter the idle state. + The exit-latency-us duration may be guaranteed + only after entry-latency-us has passed. + +- exit-latency-us + Usage: Required + Value type: <prop-encoded-array> + Definition: u32 value representing worst case latency + in microseconds required to exit the idle state. + +- min-residency-us + Usage: Required + Value type: <prop-encoded-array> + Definition: u32 value representing minimum residency duration + in microseconds after which the idle state will yield + power benefits after overcoming the overhead in entering +i the idle state. diff --git a/Documentation/devicetree/bindings/power/power_domain.txt b/Documentation/devicetree/bindings/power/power_domain.txt index 025b5e7d..723e1ad 100644 --- a/Documentation/devicetree/bindings/power/power_domain.txt +++ b/Documentation/devicetree/bindings/power/power_domain.txt @@ -29,6 +29,15 @@ Optional properties: specified by this binding. More details about power domain specifier are available in the next section. +- domain-idle-states : A phandle of an idle-state that shall be soaked into a + generic domain power state. The idle state definitions are + compatible with domain-idle-state specified in [1]. + The domain-idle-state property reflects the idle state of this PM domain and + not the idle states of the devices or sub-domains in the PM domain. Devices + and sub-domains have their own idle-states independent of the parent + domain's idle states. In the absence of this property, the domain would be + considered as capable of being powered-on or powered-off. + Example: power: power-controller@12340000 { @@ -59,6 +68,38 @@ The nodes above define two power controllers: 'parent' and 'child'. Domains created by the 'child' power controller are subdomains of '0' power domain provided by the 'parent' power controller. +Example 3: + parent: power-controller@12340000 { + compatible = "foo,power-controller"; + reg = <0x12340000 0x1000>; + #power-domain-cells = <0>; + domain-idle-states = <&DOMAIN_RET>, <&DOMAIN_PWR_DN>; + }; + + child: power-controller@12341000 { + compatible = "foo,power-controller"; + reg = <0x12341000 0x1000>; + power-domains = <&parent 0>; + #power-domain-cells = <0>; + domain-idle-states = <&DOMAIN_PWR_DN>; + }; + + DOMAIN_RET: state@0 { + compatible = "domain-idle-state"; + reg = <0x0>; + entry-latency-us = <1000>; + exit-latency-us = <2000>; + min-residency-us = <10000>; + }; + + DOMAIN_PWR_DN: state@1 { + compatible = "domain-idle-state"; + reg = <0x1>; + entry-latency-us = <5000>; + exit-latency-us = <8000>; + min-residency-us = <7000>; + }; + ==PM domain consumers== Required properties: @@ -76,3 +117,5 @@ Example: The node above defines a typical PM domain consumer device, which is located inside a PM domain with index 0 of a power controller represented by a node with the label "power". + +[1]. Documentation/devicetree/bindings/power/domain-idle-state.txt |
