diff options
Diffstat (limited to 'Documentation/devicetree')
12 files changed, 472 insertions, 9 deletions
diff --git a/Documentation/devicetree/bindings/clock/at91-clock.txt b/Documentation/devicetree/bindings/clock/at91-clock.txt index cd5e239..6794cdc 100644 --- a/Documentation/devicetree/bindings/clock/at91-clock.txt +++ b/Documentation/devicetree/bindings/clock/at91-clock.txt @@ -62,7 +62,7 @@ Required properties for PMC node: - interrupt-controller : tell that the PMC is an interrupt controller. - #interrupt-cells : must be set to 1. The first cell encodes the interrupt id, and reflect the bit position in the PMC_ER/DR/SR registers. - You can use the dt macros defined in dt-bindings/clk/at91.h. + You can use the dt macros defined in dt-bindings/clock/at91.h. 0 (AT91_PMC_MOSCS) -> main oscillator ready 1 (AT91_PMC_LOCKA) -> PLL A ready 2 (AT91_PMC_LOCKB) -> PLL B ready diff --git a/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt b/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt index 5992dce..02a25d9 100644 --- a/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt +++ b/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt @@ -43,7 +43,7 @@ Example clock-output-names = "tpu0", "mmcif1", "sdhi3", "sdhi2", "sdhi1", "sdhi0", "mmcif0"; - renesas,clock-indices = < + clock-indices = < R8A7790_CLK_TPU0 R8A7790_CLK_MMCIF1 R8A7790_CLK_SDHI3 R8A7790_CLK_SDHI2 R8A7790_CLK_SDHI1 R8A7790_CLK_SDHI0 R8A7790_CLK_MMCIF0 diff --git a/Documentation/devicetree/bindings/dma/ti-edma.txt b/Documentation/devicetree/bindings/dma/ti-edma.txt index 9fbbdb7..68ff213 100644 --- a/Documentation/devicetree/bindings/dma/ti-edma.txt +++ b/Documentation/devicetree/bindings/dma/ti-edma.txt @@ -29,6 +29,6 @@ edma: edma@49000000 { dma-channels = <64>; ti,edma-regions = <4>; ti,edma-slots = <256>; - ti,edma-xbar-event-map = <1 12 - 2 13>; + ti,edma-xbar-event-map = /bits/ 16 <1 12 + 2 13>; }; diff --git a/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt b/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt index f61cef7..941a26a 100644 --- a/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt +++ b/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt @@ -21,6 +21,12 @@ Required Properties: GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW flags are supported. - gpio-ranges: Range of pins managed by the GPIO controller. +Optional properties: + + - clocks: Must contain a reference to the functional clock. The property is + mandatory if the hardware implements a controllable functional clock for + the GPIO instance. + Please refer to gpio.txt in this directory for details of gpio-ranges property and the common GPIO bindings used by client devices. diff --git a/Documentation/devicetree/bindings/hsi/client-devices.txt b/Documentation/devicetree/bindings/hsi/client-devices.txt new file mode 100644 index 0000000..104c9a3 --- /dev/null +++ b/Documentation/devicetree/bindings/hsi/client-devices.txt @@ -0,0 +1,44 @@ +Each HSI port is supposed to have one child node, which +symbols the remote device connected to the HSI port. The +following properties are standardized for HSI clients: + +Required HSI configuration properties: + +- hsi-channel-ids: A list of channel ids + +- hsi-rx-mode: Receiver Bit transmission mode ("stream" or "frame") +- hsi-tx-mode: Transmitter Bit transmission mode ("stream" or "frame") +- hsi-mode: May be used instead hsi-rx-mode and hsi-tx-mode if + the transmission mode is the same for receiver and + transmitter +- hsi-speed-kbps: Max bit transmission speed in kbit/s +- hsi-flow: RX flow type ("synchronized" or "pipeline") +- hsi-arb-mode: Arbitration mode for TX frame ("round-robin", "priority") + +Optional HSI configuration properties: + +- hsi-channel-names: A list with one name per channel specified in the + hsi-channel-ids property + + +Device Tree node example for an HSI client: + +hsi-controller { + hsi-port { + modem: hsi-client { + compatible = "nokia,n900-modem"; + + hsi-channel-ids = <0>, <1>, <2>, <3>; + hsi-channel-names = "mcsaab-control", + "speech-control", + "speech-data", + "mcsaab-data"; + hsi-speed-kbps = <55000>; + hsi-mode = "frame"; + hsi-flow = "synchronized"; + hsi-arb-mode = "round-robin"; + + /* more client specific properties */ + }; + }; +}; diff --git a/Documentation/devicetree/bindings/hsi/nokia-modem.txt b/Documentation/devicetree/bindings/hsi/nokia-modem.txt new file mode 100644 index 0000000..8a97978 --- /dev/null +++ b/Documentation/devicetree/bindings/hsi/nokia-modem.txt @@ -0,0 +1,57 @@ +Nokia modem client bindings + +The Nokia modem HSI client follows the common HSI client binding +and inherits all required properties. The following additional +properties are needed by the Nokia modem HSI client: + +Required properties: +- compatible: Should be one of + "nokia,n900-modem" +- hsi-channel-names: Should contain the following strings + "mcsaab-control" + "speech-control" + "speech-data" + "mcsaab-data" +- gpios: Should provide a GPIO handler for each GPIO listed in + gpio-names +- gpio-names: Should contain the following strings + "cmt_apeslpx" + "cmt_rst_rq" + "cmt_en" + "cmt_rst" + "cmt_bsi" +- interrupts: Should be IRQ handle for modem's reset indication + +Example: + +&ssi_port { + modem: hsi-client { + compatible = "nokia,n900-modem"; + + pinctrl-names = "default"; + pinctrl-0 = <&modem_pins>; + + hsi-channel-ids = <0>, <1>, <2>, <3>; + hsi-channel-names = "mcsaab-control", + "speech-control", + "speech-data", + "mcsaab-data"; + hsi-speed-kbps = <55000>; + hsi-mode = "frame"; + hsi-flow = "synchronized"; + hsi-arb-mode = "round-robin"; + + interrupts-extended = <&gpio3 8 IRQ_TYPE_EDGE_FALLING>; /* 72 */ + + gpios = <&gpio3 6 GPIO_ACTIVE_HIGH>, /* 70 */ + <&gpio3 9 GPIO_ACTIVE_HIGH>, /* 73 */ + <&gpio3 10 GPIO_ACTIVE_HIGH>, /* 74 */ + <&gpio3 11 GPIO_ACTIVE_HIGH>, /* 75 */ + <&gpio5 29 GPIO_ACTIVE_HIGH>; /* 157 */ + gpio-names = "cmt_apeslpx", + "cmt_rst_rq", + "cmt_en", + "cmt_rst", + "cmt_bsi"; + }; +}; diff --git a/Documentation/devicetree/bindings/hsi/omap-ssi.txt b/Documentation/devicetree/bindings/hsi/omap-ssi.txt new file mode 100644 index 0000000..f26625e --- /dev/null +++ b/Documentation/devicetree/bindings/hsi/omap-ssi.txt @@ -0,0 +1,97 @@ +OMAP SSI controller bindings + +OMAP Synchronous Serial Interface (SSI) controller implements a legacy +variant of MIPI's High Speed Synchronous Serial Interface (HSI). + +Required properties: +- compatible: Should include "ti,omap3-ssi". +- reg-names: Contains the values "sys" and "gdd" (in this order). +- reg: Contains a matching register specifier for each entry + in reg-names. +- interrupt-names: Contains the value "gdd_mpu". +- interrupts: Contains matching interrupt information for each entry + in interrupt-names. +- ranges: Represents the bus address mapping between the main + controller node and the child nodes below. +- clock-names: Must include the following entries: + "ssi_ssr_fck": The OMAP clock of that name + "ssi_sst_fck": The OMAP clock of that name + "ssi_ick": The OMAP clock of that name +- clocks: Contains a matching clock specifier for each entry in + clock-names. +- #address-cells: Should be set to <1> +- #size-cells: Should be set to <1> + +Each port is represented as a sub-node of the ti,omap3-ssi device. + +Required Port sub-node properties: +- compatible: Should be set to the following value + ti,omap3-ssi-port (applicable to OMAP34xx devices) +- reg-names: Contains the values "tx" and "rx" (in this order). +- reg: Contains a matching register specifier for each entry + in reg-names. +- interrupt-parent Should be a phandle for the interrupt controller +- interrupts: Should contain interrupt specifiers for mpu interrupts + 0 and 1 (in this order). +- ti,ssi-cawake-gpio: Defines which GPIO pin is used to signify CAWAKE + events for the port. This is an optional board-specific + property. If it's missing the port will not be + enabled. + +Example for Nokia N900: + +ssi-controller@48058000 { + compatible = "ti,omap3-ssi"; + + /* needed until hwmod is updated to use the compatible string */ + ti,hwmods = "ssi"; + + reg = <0x48058000 0x1000>, + <0x48059000 0x1000>; + reg-names = "sys", + "gdd"; + + interrupts = <55>; + interrupt-names = "gdd_mpu"; + + clocks = <&ssi_ssr_fck>, + <&ssi_sst_fck>, + <&ssi_ick>; + clock-names = "ssi_ssr_fck", + "ssi_sst_fck", + "ssi_ick"; + + #address-cells = <1>; + #size-cells = <1>; + ranges; + + ssi-port@4805a000 { + compatible = "ti,omap3-ssi-port"; + + reg = <0x4805a000 0x800>, + <0x4805a800 0x800>; + reg-names = "tx", + "rx"; + + interrupt-parent = <&intc>; + interrupts = <67>, + <68>; + + ti,ssi-cawake-gpio = <&gpio5 23 GPIO_ACTIVE_HIGH>; /* 151 */ + } + + ssi-port@4805a000 { + compatible = "ti,omap3-ssi-port"; + + reg = <0x4805b000 0x800>, + <0x4805b800 0x800>; + reg-names = "tx", + "rx"; + + interrupt-parent = <&intc>; + interrupts = <69>, + <70>; + + status = "disabled"; /* second port is not used on N900 */ + } +} diff --git a/Documentation/devicetree/bindings/mmc/mmci.txt b/Documentation/devicetree/bindings/mmc/mmci.txt index 2b584ca..03796cf 100644 --- a/Documentation/devicetree/bindings/mmc/mmci.txt +++ b/Documentation/devicetree/bindings/mmc/mmci.txt @@ -4,12 +4,58 @@ The ARM PrimeCell MMCI PL180 and PL181 provides an interface for reading and writing to MultiMedia and SD cards alike. This file documents differences between the core properties described -by mmc.txt and the properties used by the mmci driver. +by mmc.txt and the properties used by the mmci driver. Using "st" as +the prefix for a property, indicates support by the ST Micro variant. Required properties: - compatible : contains "arm,pl18x", "arm,primecell". -- arm,primecell-periphid : contains the PrimeCell Peripheral ID. +- vmmc-supply : phandle to the regulator device tree node, mentioned + as the VCC/VDD supply in the eMMC/SD specs. Optional properties: -- mmc-cap-mmc-highspeed : indicates whether MMC is high speed capable -- mmc-cap-sd-highspeed : indicates whether SD is high speed capable +- arm,primecell-periphid : contains the PrimeCell Peripheral ID, it overrides + the ID provided by the HW +- vqmmc-supply : phandle to the regulator device tree node, mentioned + as the VCCQ/VDD_IO supply in the eMMC/SD specs. +- st,sig-dir-dat0 : bus signal direction pin used for DAT[0]. +- st,sig-dir-dat2 : bus signal direction pin used for DAT[2]. +- st,sig-dir-dat31 : bus signal direction pin used for DAT[3] and DAT[1]. +- st,sig-dir-dat74 : bus signal direction pin used for DAT[4] to DAT[7]. +- st,sig-dir-cmd : cmd signal direction pin used for CMD. +- st,sig-pin-fbclk : feedback clock signal pin used. + +Deprecated properties: +- mmc-cap-mmc-highspeed : indicates whether MMC is high speed capable. +- mmc-cap-sd-highspeed : indicates whether SD is high speed capable. + +Example: + +sdi0_per1@80126000 { + compatible = "arm,pl18x", "arm,primecell"; + reg = <0x80126000 0x1000>; + interrupts = <0 60 IRQ_TYPE_LEVEL_HIGH>; + + dmas = <&dma 29 0 0x2>, /* Logical - DevToMem */ + <&dma 29 0 0x0>; /* Logical - MemToDev */ + dma-names = "rx", "tx"; + + clocks = <&prcc_kclk 1 5>, <&prcc_pclk 1 5>; + clock-names = "sdi", "apb_pclk"; + + max-frequency = <100000000>; + bus-width = <4>; + cap-sd-highspeed; + cap-mmc-highspeed; + cd-gpios = <&gpio2 31 0x4>; // 95 + st,sig-dir-dat0; + st,sig-dir-dat2; + st,sig-dir-cmd; + st,sig-pin-fbclk; + + vmmc-supply = <&ab8500_ldo_aux3_reg>; + vqmmc-supply = <&vmmci>; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdi0_default_mode>; + pinctrl-1 = <&sdi0_sleep_mode>; +}; diff --git a/Documentation/devicetree/bindings/net/mdio-gpio.txt b/Documentation/devicetree/bindings/net/mdio-gpio.txt index c79bab0..8dbcf82 100644 --- a/Documentation/devicetree/bindings/net/mdio-gpio.txt +++ b/Documentation/devicetree/bindings/net/mdio-gpio.txt @@ -14,7 +14,7 @@ node. Example: aliases { - mdio-gpio0 = <&mdio0>; + mdio-gpio0 = &mdio0; }; mdio0: mdio { diff --git a/Documentation/devicetree/bindings/pci/host-generic-pci.txt b/Documentation/devicetree/bindings/pci/host-generic-pci.txt new file mode 100644 index 0000000..f0b0436 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/host-generic-pci.txt @@ -0,0 +1,100 @@ +* Generic PCI host controller + +Firmware-initialised PCI host controllers and PCI emulations, such as the +virtio-pci implementations found in kvmtool and other para-virtualised +systems, do not require driver support for complexities such as regulator +and clock management. In fact, the controller may not even require the +configuration of a control interface by the operating system, instead +presenting a set of fixed windows describing a subset of IO, Memory and +Configuration Spaces. + +Such a controller can be described purely in terms of the standardized device +tree bindings communicated in pci.txt: + + +Properties of the host controller node: + +- compatible : Must be "pci-host-cam-generic" or "pci-host-ecam-generic" + depending on the layout of configuration space (CAM vs + ECAM respectively). + +- device_type : Must be "pci". + +- ranges : As described in IEEE Std 1275-1994, but must provide + at least a definition of non-prefetchable memory. One + or both of prefetchable Memory and IO Space may also + be provided. + +- bus-range : Optional property (also described in IEEE Std 1275-1994) + to indicate the range of bus numbers for this controller. + If absent, defaults to <0 255> (i.e. all buses). + +- #address-cells : Must be 3. + +- #size-cells : Must be 2. + +- reg : The Configuration Space base address and size, as accessed + from the parent bus. + + +Properties of the /chosen node: + +- linux,pci-probe-only + : Optional property which takes a single-cell argument. + If '0', then Linux will assign devices in its usual manner, + otherwise it will not try to assign devices and instead use + them as they are configured already. + +Configuration Space is assumed to be memory-mapped (as opposed to being +accessed via an ioport) and laid out with a direct correspondence to the +geography of a PCI bus address by concatenating the various components to +form an offset. + +For CAM, this 24-bit offset is: + + cfg_offset(bus, device, function, register) = + bus << 16 | device << 11 | function << 8 | register + +Whilst ECAM extends this by 4 bits to accomodate 4k of function space: + + cfg_offset(bus, device, function, register) = + bus << 20 | device << 15 | function << 12 | register + +Interrupt mapping is exactly as described in `Open Firmware Recommended +Practice: Interrupt Mapping' and requires the following properties: + +- #interrupt-cells : Must be 1 + +- interrupt-map : <see aforementioned specification> + +- interrupt-map-mask : <see aforementioned specification> + + +Example: + +pci { + compatible = "pci-host-cam-generic" + device_type = "pci"; + #address-cells = <3>; + #size-cells = <2>; + bus-range = <0x0 0x1>; + + // CPU_PHYSICAL(2) SIZE(2) + reg = <0x0 0x40000000 0x0 0x1000000>; + + // BUS_ADDRESS(3) CPU_PHYSICAL(2) SIZE(2) + ranges = <0x01000000 0x0 0x01000000 0x0 0x01000000 0x0 0x00010000>, + <0x02000000 0x0 0x41000000 0x0 0x41000000 0x0 0x3f000000>; + + + #interrupt-cells = <0x1>; + + // PCI_DEVICE(3) INT#(1) CONTROLLER(PHANDLE) CONTROLLER_DATA(3) + interrupt-map = < 0x0 0x0 0x0 0x1 &gic 0x0 0x4 0x1 + 0x800 0x0 0x0 0x1 &gic 0x0 0x5 0x1 + 0x1000 0x0 0x0 0x1 &gic 0x0 0x6 0x1 + 0x1800 0x0 0x0 0x1 &gic 0x0 0x7 0x1>; + + // PCI_DEVICE(3) INT#(1) + interrupt-map-mask = <0xf800 0x0 0x0 0x7>; +} diff --git a/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt b/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt new file mode 100644 index 0000000..d8ef5bf --- /dev/null +++ b/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt @@ -0,0 +1,66 @@ +Renesas AHB to PCI bridge +------------------------- + +This is the bridge used internally to connect the USB controllers to the +AHB. There is one bridge instance per USB port connected to the internal +OHCI and EHCI controllers. + +Required properties: +- compatible: "renesas,pci-r8a7790" for the R8A7790 SoC; + "renesas,pci-r8a7791" for the R8A7791 SoC. +- reg: A list of physical regions to access the device: the first is + the operational registers for the OHCI/EHCI controllers and the + second is for the bridge configuration and control registers. +- interrupts: interrupt for the device. +- clocks: The reference to the device clock. +- bus-range: The PCI bus number range; as this is a single bus, the range + should be specified as the same value twice. +- #address-cells: must be 3. +- #size-cells: must be 2. +- #interrupt-cells: must be 1. +- interrupt-map: standard property used to define the mapping of the PCI + interrupts to the GIC interrupts. +- interrupt-map-mask: standard property that helps to define the interrupt + mapping. + +Example SoC configuration: + + pci0: pci@ee090000 { + compatible = "renesas,pci-r8a7790"; + clocks = <&mstp7_clks R8A7790_CLK_EHCI>; + reg = <0x0 0xee090000 0x0 0xc00>, + <0x0 0xee080000 0x0 0x1100>; + interrupts = <0 108 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + + bus-range = <0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + interrupt-map-mask = <0xff00 0 0 0x7>; + interrupt-map = <0x0000 0 0 1 &gic 0 108 IRQ_TYPE_LEVEL_HIGH + 0x0800 0 0 1 &gic 0 108 IRQ_TYPE_LEVEL_HIGH + 0x1000 0 0 2 &gic 0 108 IRQ_TYPE_LEVEL_HIGH>; + + pci@0,1 { + reg = <0x800 0 0 0 0>; + device_type = "pci"; + phys = <&usbphy 0 0>; + phy-names = "usb"; + }; + + pci@0,2 { + reg = <0x1000 0 0 0 0>; + device_type = "pci"; + phys = <&usbphy 0 0>; + phy-names = "usb"; + }; + }; + +Example board setup: + +&pci0 { + status = "okay"; + pinctrl-0 = <&usb0_pins>; + pinctrl-names = "default"; +}; diff --git a/Documentation/devicetree/bindings/pci/rcar-pci.txt b/Documentation/devicetree/bindings/pci/rcar-pci.txt new file mode 100644 index 0000000..29d3b98 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/rcar-pci.txt @@ -0,0 +1,47 @@ +* Renesas RCar PCIe interface + +Required properties: +- compatible: should contain one of the following + "renesas,pcie-r8a7779", "renesas,pcie-r8a7790", "renesas,pcie-r8a7791" +- reg: base address and length of the pcie controller registers. +- #address-cells: set to <3> +- #size-cells: set to <2> +- bus-range: PCI bus numbers covered +- device_type: set to "pci" +- ranges: ranges for the PCI memory and I/O regions. +- dma-ranges: ranges for the inbound memory regions. +- interrupts: two interrupt sources for MSI interrupts, followed by interrupt + source for hardware related interrupts (e.g. link speed change). +- #interrupt-cells: set to <1> +- interrupt-map-mask and interrupt-map: standard PCI properties + to define the mapping of the PCIe interface to interrupt + numbers. +- clocks: from common clock binding: clock specifiers for the PCIe controller + and PCIe bus clocks. +- clock-names: from common clock binding: should be "pcie" and "pcie_bus". + +Example: + +SoC specific DT Entry: + + pcie: pcie@fe000000 { + compatible = "renesas,pcie-r8a7791"; + reg = <0 0xfe000000 0 0x80000>; + #address-cells = <3>; + #size-cells = <2>; + bus-range = <0x00 0xff>; + device_type = "pci"; + ranges = <0x01000000 0 0x00000000 0 0xfe100000 0 0x00100000 + 0x02000000 0 0xfe200000 0 0xfe200000 0 0x00200000 + 0x02000000 0 0x30000000 0 0x30000000 0 0x08000000 + 0x42000000 0 0x38000000 0 0x38000000 0 0x08000000>; + dma-ranges = <0x42000000 0 0x40000000 0 0x40000000 0 0x40000000 + 0x42000000 2 0x00000000 2 0x00000000 0 0x40000000>; + interrupts = <0 116 4>, <0 117 4>, <0 118 4>; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic 0 116 4>; + clocks = <&mstp3_clks R8A7791_CLK_PCIE>, <&pcie_bus_clk>; + clock-names = "pcie", "pcie_bus"; + status = "disabled"; + }; |
