diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
10 files changed, 194 insertions, 11 deletions
diff --git a/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt b/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt index d01ed63..42409bf 100644 --- a/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt +++ b/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt @@ -8,10 +8,16 @@ Required properties: - SerDes integration registers (1/2) - SerDes integration registers (2/2) +Optional properties: +- amd,speed-set: Speed capabilities of the device + 0 - 1GbE and 10GbE (default) + 1 - 2.5GbE and 10GbE + Example: xgbe_phy@e1240800 { compatible = "amd,xgbe-phy-seattle-v1a", "ethernet-phy-ieee802.3-c45"; reg = <0 0xe1240800 0 0x00400>, <0 0xe1250000 0 0x00060>, <0 0xe1250080 0 0x00004>; + amd,speed-set = <0>; }; diff --git a/Documentation/devicetree/bindings/net/amd-xgbe.txt b/Documentation/devicetree/bindings/net/amd-xgbe.txt index ea0c790..41354f7 100644 --- a/Documentation/devicetree/bindings/net/amd-xgbe.txt +++ b/Documentation/devicetree/bindings/net/amd-xgbe.txt @@ -8,16 +8,21 @@ Required properties: - interrupt-parent: Should be the phandle for the interrupt controller that services interrupts for this device - interrupts: Should contain the amd-xgbe interrupt -- clocks: Should be the DMA clock for the amd-xgbe device (used for - calculating the correct Rx interrupt watchdog timer value on a DMA - channel for coalescing) -- clock-names: Should be the name of the DMA clock, "dma_clk" +- clocks: + - DMA clock for the amd-xgbe device (used for calculating the + correct Rx interrupt watchdog timer value on a DMA channel + for coalescing) + - PTP clock for the amd-xgbe device +- clock-names: Should be the names of the clocks + - "dma_clk" for the DMA clock + - "ptp_clk" for the PTP clock - phy-handle: See ethernet.txt file in the same directory - phy-mode: See ethernet.txt file in the same directory Optional properties: - mac-address: mac address to be assigned to the device. Can be overridden by UEFI. +- dma-coherent: Present if dma operations are coherent Example: xgbe@e0700000 { @@ -26,8 +31,8 @@ Example: <0 0xe0780000 0 0x80000>; interrupt-parent = <&gic>; interrupts = <0 325 4>; - clocks = <&xgbe_clk>; - clock-names = "dma_clk"; + clocks = <&xgbe_dma_clk>, <&xgbe_ptp_clk>; + clock-names = "dma_clk", "ptp_clk"; phy-handle = <&phy>; phy-mode = "xgmii"; mac-address = [ 02 a1 a2 a3 a4 a5 ]; diff --git a/Documentation/devicetree/bindings/net/broadcom-systemport.txt b/Documentation/devicetree/bindings/net/broadcom-systemport.txt index c183ea9..aa7ad62 100644 --- a/Documentation/devicetree/bindings/net/broadcom-systemport.txt +++ b/Documentation/devicetree/bindings/net/broadcom-systemport.txt @@ -4,7 +4,8 @@ Required properties: - compatible: should be one of "brcm,systemport-v1.00" or "brcm,systemport" - reg: address and length of the register set for the device. - interrupts: interrupts for the device, first cell must be for the the rx - interrupts, and the second cell should be for the transmit queues + interrupts, and the second cell should be for the transmit queues. An + optional third interrupt cell for Wake-on-LAN can be specified - local-mac-address: Ethernet MAC address (48 bits) of this adapter - phy-mode: Should be a string describing the PHY interface to the Ethernet switch/PHY, see Documentation/devicetree/bindings/net/ethernet.txt diff --git a/Documentation/devicetree/bindings/net/davinci-mdio.txt b/Documentation/devicetree/bindings/net/davinci-mdio.txt index 72efaaf..0369e25 100644 --- a/Documentation/devicetree/bindings/net/davinci-mdio.txt +++ b/Documentation/devicetree/bindings/net/davinci-mdio.txt @@ -1,8 +1,8 @@ -TI SoC Davinci MDIO Controller Device Tree Bindings +TI SoC Davinci/Keystone2 MDIO Controller Device Tree Bindings --------------------------------------------------- Required properties: -- compatible : Should be "ti,davinci_mdio" +- compatible : Should be "ti,davinci_mdio" or "ti,keystone_mdio" - reg : physical base address and size of the davinci mdio registers map - bus_freq : Mdio Bus frequency @@ -19,7 +19,7 @@ file. Examples: mdio: davinci_mdio@4A101000 { - compatible = "ti,cpsw"; + compatible = "ti,davinci_mdio"; reg = <0x4A101000 0x1000>; bus_freq = <1000000>; }; @@ -27,7 +27,7 @@ Examples: (or) mdio: davinci_mdio@4A101000 { - compatible = "ti,cpsw"; + compatible = "ti,davinci_mdio"; ti,hwmods = "davinci_mdio"; bus_freq = <1000000>; }; diff --git a/Documentation/devicetree/bindings/net/ieee802154/cc2520.txt b/Documentation/devicetree/bindings/net/ieee802154/cc2520.txt new file mode 100644 index 0000000..0071883 --- /dev/null +++ b/Documentation/devicetree/bindings/net/ieee802154/cc2520.txt @@ -0,0 +1,29 @@ +*CC2520 IEEE 802.15.4 Compatible Radio* + +Required properties: + - compatible: should be "ti,cc2520" + - spi-max-frequency: maximal bus speed (8000000), should be set to 4000000 depends + sync or async operation mode + - reg: the chipselect index + - pinctrl-0: pin control group to be used for this controller. + - pinctrl-names: must contain a "default" entry. + - fifo-gpio: GPIO spec for the FIFO pin + - fifop-gpio: GPIO spec for the FIFOP pin + - sfd-gpio: GPIO spec for the SFD pin + - cca-gpio: GPIO spec for the CCA pin + - vreg-gpio: GPIO spec for the VREG pin + - reset-gpio: GPIO spec for the RESET pin +Example: + cc2520@0 { + compatible = "ti,cc2520"; + reg = <0>; + spi-max-frequency = <4000000>; + pinctrl-names = "default"; + pinctrl-0 = <&cc2520_cape_pins>; + fifo-gpio = <&gpio1 18 0>; + fifop-gpio = <&gpio1 19 0>; + sfd-gpio = <&gpio1 13 0>; + cca-gpio = <&gpio1 16 0>; + vreg-gpio = <&gpio0 31 0>; + reset-gpio = <&gpio1 12 0>; + }; diff --git a/Documentation/devicetree/bindings/net/marvell-pp2.txt b/Documentation/devicetree/bindings/net/marvell-pp2.txt new file mode 100644 index 0000000..aa4f423 --- /dev/null +++ b/Documentation/devicetree/bindings/net/marvell-pp2.txt @@ -0,0 +1,61 @@ +* Marvell Armada 375 Ethernet Controller (PPv2) + +Required properties: + +- compatible: should be "marvell,armada-375-pp2" +- reg: addresses and length of the register sets for the device. + Must contain the following register sets: + - common controller registers + - LMS registers + In addition, at least one port register set is required. +- clocks: a pointer to the reference clocks for this device, consequently: + - main controller clock + - GOP clock +- clock-names: names of used clocks, must be "pp_clk" and "gop_clk". + +The ethernet ports are represented by subnodes. At least one port is +required. + +Required properties (port): + +- interrupts: interrupt for the port +- port-id: should be '0' or '1' for ethernet ports, and '2' for the + loopback port +- phy-mode: See ethernet.txt file in the same directory + +Optional properties (port): + +- marvell,loopback: port is loopback mode +- phy: a phandle to a phy node defining the PHY address (as the reg + property, a single integer). Note: if this property isn't present, + then fixed link is assumed, and the 'fixed-link' property is + mandatory. + +Example: + +ethernet@f0000 { + compatible = "marvell,armada-375-pp2"; + reg = <0xf0000 0xa000>, + <0xc0000 0x3060>, + <0xc4000 0x100>, + <0xc5000 0x100>; + clocks = <&gateclk 3>, <&gateclk 19>; + clock-names = "pp_clk", "gop_clk"; + status = "okay"; + + eth0: eth0@c4000 { + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; + port-id = <0>; + status = "okay"; + phy = <&phy0>; + phy-mode = "gmii"; + }; + + eth1: eth1@c5000 { + interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; + port-id = <1>; + status = "okay"; + phy = <&phy3>; + phy-mode = "gmii"; + }; +}; diff --git a/Documentation/devicetree/bindings/net/nfc/st21nfcb.txt b/Documentation/devicetree/bindings/net/nfc/st21nfcb.txt new file mode 100644 index 0000000..3b58ae4 --- /dev/null +++ b/Documentation/devicetree/bindings/net/nfc/st21nfcb.txt @@ -0,0 +1,33 @@ +* STMicroelectronics SAS. ST21NFCB NFC Controller + +Required properties: +- compatible: Should be "st,st21nfcb_i2c". +- clock-frequency: I²C work frequency. +- reg: address on the bus +- interrupt-parent: phandle for the interrupt gpio controller +- interrupts: GPIO interrupt to which the chip is connected +- reset-gpios: Output GPIO pin used to reset the ST21NFCB + +Optional SoC Specific Properties: +- pinctrl-names: Contains only one value - "default". +- pintctrl-0: Specifies the pin control groups used for this controller. + +Example (for ARM-based BeagleBoard xM with ST21NFCB on I2C2): + +&i2c2 { + + status = "okay"; + + st21nfcb: st21nfcb@8 { + + compatible = "st,st21nfcb_i2c"; + + reg = <0x08>; + clock-frequency = <400000>; + + interrupt-parent = <&gpio5>; + interrupts = <2 IRQ_TYPE_LEVEL_LOW>; + + reset-gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/sh_eth.txt b/Documentation/devicetree/bindings/net/sh_eth.txt index e7106b5..34d4db1 100644 --- a/Documentation/devicetree/bindings/net/sh_eth.txt +++ b/Documentation/devicetree/bindings/net/sh_eth.txt @@ -9,6 +9,7 @@ Required properties: "renesas,ether-r8a7779" if the device is a part of R8A7779 SoC. "renesas,ether-r8a7790" if the device is a part of R8A7790 SoC. "renesas,ether-r8a7791" if the device is a part of R8A7791 SoC. + "renesas,ether-r8a7794" if the device is a part of R8A7794 SoC. "renesas,ether-r7s72100" if the device is a part of R7S72100 SoC. - reg: offset and length of (1) the E-DMAC/feLic register block (required), (2) the TSU register block (optional). diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt index a2acd2b..9b03c57 100644 --- a/Documentation/devicetree/bindings/net/stmmac.txt +++ b/Documentation/devicetree/bindings/net/stmmac.txt @@ -25,6 +25,10 @@ Required properties: - snps,force_sf_dma_mode Force DMA to use the Store and Forward mode for both tx and rx. This flag is ignored if force_thresh_dma_mode is set. +- snps,multicast-filter-bins: Number of multicast filter hash bins + supported by this device instance +- snps,perfect-filter-entries: Number of perfect filter entries supported + by this device instance Optional properties: - resets: Should contain a phandle to the STMMAC reset signal, if any @@ -47,6 +51,8 @@ Examples: mac-address = [000000000000]; /* Filled in by U-Boot */ max-frame-size = <3800>; phy-mode = "gmii"; + snps,multicast-filter-bins = <256>; + snps,perfect-filter-entries = <128>; clocks = <&clock>; clock-names = "stmmaceth">; }; diff --git a/Documentation/devicetree/bindings/net/wireless/brcm,bcm43xx-fmac.txt b/Documentation/devicetree/bindings/net/wireless/brcm,bcm43xx-fmac.txt new file mode 100644 index 0000000..5dbf169 --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/brcm,bcm43xx-fmac.txt @@ -0,0 +1,41 @@ +Broadcom BCM43xx Fullmac wireless SDIO devices + +This node provides properties for controlling the Broadcom wireless device. The +node is expected to be specified as a child node to the SDIO controller that +connects the device to the system. + +Required properties: + + - compatible : Should be "brcm,bcm4329-fmac". + +Optional properties: + - brcm,drive-strength : drive strength used for SDIO pins on device in mA + (default = 6). + - interrupt-parent : the phandle for the interrupt controller to which the + device interrupts are connected. + - interrupts : specifies attributes for the out-of-band interrupt (host-wake). + When not specified the device will use in-band SDIO interrupts. + - interrupt-names : name of the out-of-band interrupt, which must be set + to "host-wake". + +Example: + +mmc3: mmc@01c12000 { + #address-cells = <1>; + #size-cells = <0>; + + pinctrl-names = "default"; + pinctrl-0 = <&mmc3_pins_a>; + vmmc-supply = <®_vmmc3>; + bus-width = <4>; + non-removable; + status = "okay"; + + brcmf: bcrmf@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + interrupt-parent = <&pio>; + interrupts = <10 8>; /* PH10 / EINT10 */ + interrupt-names = "host-wake"; + }; +}; |
