diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
4 files changed, 266 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/net/can/c_can.txt b/Documentation/devicetree/bindings/net/can/c_can.txt new file mode 100644 index 0000000..8f1ae81 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/c_can.txt @@ -0,0 +1,49 @@ +Bosch C_CAN/D_CAN controller Device Tree Bindings +------------------------------------------------- + +Required properties: +- compatible : Should be "bosch,c_can" for C_CAN controllers and + "bosch,d_can" for D_CAN controllers. +- reg : physical base address and size of the C_CAN/D_CAN + registers map +- interrupts : property with a value describing the interrupt + number + +Optional properties: +- ti,hwmods : Must be "d_can<n>" or "c_can<n>", n being the + instance number + +Note: "ti,hwmods" field is used to fetch the base address and irq +resources from TI, omap hwmod data base during device registration. +Future plan is to migrate hwmod data base contents into device tree +blob so that, all the required data will be used from device tree dts +file. + +Example: + +Step1: SoC common .dtsi file + + dcan1: d_can@481d0000 { + compatible = "bosch,d_can"; + reg = <0x481d0000 0x2000>; + interrupts = <55>; + interrupt-parent = <&intc>; + status = "disabled"; + }; + +(or) + + dcan1: d_can@481d0000 { + compatible = "bosch,d_can"; + ti,hwmods = "d_can1"; + reg = <0x481d0000 0x2000>; + interrupts = <55>; + interrupt-parent = <&intc>; + status = "disabled"; + }; + +Step 2: board specific .dts file + + &dcan1 { + status = "okay"; + }; diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt new file mode 100644 index 0000000..dcaabe9 --- /dev/null +++ b/Documentation/devicetree/bindings/net/cpsw.txt @@ -0,0 +1,109 @@ +TI SoC Ethernet Switch Controller Device Tree Bindings +------------------------------------------------------ + +Required properties: +- compatible : Should be "ti,cpsw" +- reg : physical base address and size of the cpsw + registers map +- interrupts : property with a value describing the interrupt + number +- interrupt-parent : The parent interrupt controller +- cpdma_channels : Specifies number of channels in CPDMA +- host_port_no : Specifies host port shift +- cpdma_reg_ofs : Specifies CPDMA submodule register offset +- cpdma_sram_ofs : Specifies CPDMA SRAM offset +- ale_reg_ofs : Specifies ALE submodule register offset +- ale_entries : Specifies No of entries ALE can hold +- host_port_reg_ofs : Specifies host port register offset +- hw_stats_reg_ofs : Specifies hardware statistics register offset +- bd_ram_ofs : Specifies internal desciptor RAM offset +- bd_ram_size : Specifies internal descriptor RAM size +- rx_descs : Specifies number of Rx descriptors +- mac_control : Specifies Default MAC control register content + for the specific platform +- slaves : Specifies number for slaves +- slave_reg_ofs : Specifies slave register offset +- sliver_reg_ofs : Specifies slave sliver register offset +- phy_id : Specifies slave phy id +- mac-address : Specifies slave MAC address + +Optional properties: +- ti,hwmods : Must be "cpgmac0" +- no_bd_ram : Must be 0 or 1 + +Note: "ti,hwmods" field is used to fetch the base address and irq +resources from TI, omap hwmod data base during device registration. +Future plan is to migrate hwmod data base contents into device tree +blob so that, all the required data will be used from device tree dts +file. + +Examples: + + mac: ethernet@4A100000 { + compatible = "ti,cpsw"; + reg = <0x4A100000 0x1000>; + interrupts = <55 0x4>; + interrupt-parent = <&intc>; + cpdma_channels = <8>; + host_port_no = <0>; + cpdma_reg_ofs = <0x800>; + cpdma_sram_ofs = <0xa00>; + ale_reg_ofs = <0xd00>; + ale_entries = <1024>; + host_port_reg_ofs = <0x108>; + hw_stats_reg_ofs = <0x900>; + bd_ram_ofs = <0x2000>; + bd_ram_size = <0x2000>; + no_bd_ram = <0>; + rx_descs = <64>; + mac_control = <0x20>; + slaves = <2>; + cpsw_emac0: slave@0 { + slave_reg_ofs = <0x208>; + sliver_reg_ofs = <0xd80>; + phy_id = "davinci_mdio.16:00"; + /* Filled in by U-Boot */ + mac-address = [ 00 00 00 00 00 00 ]; + }; + cpsw_emac1: slave@1 { + slave_reg_ofs = <0x308>; + sliver_reg_ofs = <0xdc0>; + phy_id = "davinci_mdio.16:01"; + /* Filled in by U-Boot */ + mac-address = [ 00 00 00 00 00 00 ]; + }; + }; + +(or) + mac: ethernet@4A100000 { + compatible = "ti,cpsw"; + ti,hwmods = "cpgmac0"; + cpdma_channels = <8>; + host_port_no = <0>; + cpdma_reg_ofs = <0x800>; + cpdma_sram_ofs = <0xa00>; + ale_reg_ofs = <0xd00>; + ale_entries = <1024>; + host_port_reg_ofs = <0x108>; + hw_stats_reg_ofs = <0x900>; + bd_ram_ofs = <0x2000>; + bd_ram_size = <0x2000>; + no_bd_ram = <0>; + rx_descs = <64>; + mac_control = <0x20>; + slaves = <2>; + cpsw_emac0: slave@0 { + slave_reg_ofs = <0x208>; + sliver_reg_ofs = <0xd80>; + phy_id = "davinci_mdio.16:00"; + /* Filled in by U-Boot */ + mac-address = [ 00 00 00 00 00 00 ]; + }; + cpsw_emac1: slave@1 { + slave_reg_ofs = <0x308>; + sliver_reg_ofs = <0xdc0>; + phy_id = "davinci_mdio.16:01"; + /* Filled in by U-Boot */ + mac-address = [ 00 00 00 00 00 00 ]; + }; + }; diff --git a/Documentation/devicetree/bindings/net/davinci-mdio.txt b/Documentation/devicetree/bindings/net/davinci-mdio.txt new file mode 100644 index 0000000..72efaaf --- /dev/null +++ b/Documentation/devicetree/bindings/net/davinci-mdio.txt @@ -0,0 +1,33 @@ +TI SoC Davinci MDIO Controller Device Tree Bindings +--------------------------------------------------- + +Required properties: +- compatible : Should be "ti,davinci_mdio" +- reg : physical base address and size of the davinci mdio + registers map +- bus_freq : Mdio Bus frequency + +Optional properties: +- ti,hwmods : Must be "davinci_mdio" + +Note: "ti,hwmods" field is used to fetch the base address and irq +resources from TI, omap hwmod data base during device registration. +Future plan is to migrate hwmod data base contents into device tree +blob so that, all the required data will be used from device tree dts +file. + +Examples: + + mdio: davinci_mdio@4A101000 { + compatible = "ti,cpsw"; + reg = <0x4A101000 0x1000>; + bus_freq = <1000000>; + }; + +(or) + + mdio: davinci_mdio@4A101000 { + compatible = "ti,cpsw"; + ti,hwmods = "davinci_mdio"; + bus_freq = <1000000>; + }; diff --git a/Documentation/devicetree/bindings/net/mdio-mux-mmioreg.txt b/Documentation/devicetree/bindings/net/mdio-mux-mmioreg.txt new file mode 100644 index 0000000..8516929 --- /dev/null +++ b/Documentation/devicetree/bindings/net/mdio-mux-mmioreg.txt @@ -0,0 +1,75 @@ +Properties for an MDIO bus multiplexer controlled by a memory-mapped device + +This is a special case of a MDIO bus multiplexer. A memory-mapped device, +like an FPGA, is used to control which child bus is connected. The mdio-mux +node must be a child of the memory-mapped device. The driver currently only +supports devices with eight-bit registers. + +Required properties in addition to the generic multiplexer properties: + +- compatible : string, must contain "mdio-mux-mmioreg" + +- reg : integer, contains the offset of the register that controls the bus + multiplexer. The size field in the 'reg' property is the size of + register, and must therefore be 1. + +- mux-mask : integer, contains an eight-bit mask that specifies which + bits in the register control the actual bus multiplexer. The + 'reg' property of each child mdio-mux node must be constrained by + this mask. + +Example: + +The FPGA node defines a memory-mapped FPGA with a register space of 0x30 bytes. +For the "EMI2" MDIO bus, register 9 (BRDCFG1) controls the mux on that bus. +A bitmask of 0x6 means that bits 1 and 2 (bit 0 is lsb) are the bits on +BRDCFG1 that control the actual mux. + + /* The FPGA node */ + fpga: board-control@3,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,p5020ds-fpga", "fsl,fpga-ngpixis"; + reg = <3 0 0x30>; + ranges = <0 3 0 0x30>; + + mdio-mux-emi2 { + compatible = "mdio-mux-mmioreg", "mdio-mux"; + mdio-parent-bus = <&xmdio0>; + #address-cells = <1>; + #size-cells = <0>; + reg = <9 1>; // BRDCFG1 + mux-mask = <0x6>; // EMI2 + + emi2_slot1: mdio@0 { // Slot 1 XAUI (FM2) + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + + phy_xgmii_slot1: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <4>; + }; + }; + + emi2_slot2: mdio@2 { // Slot 2 XAUI (FM1) + reg = <2>; + #address-cells = <1>; + #size-cells = <0>; + + phy_xgmii_slot2: ethernet-phy@4 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <0>; + }; + }; + }; + }; + + /* The parent MDIO bus. */ + xmdio0: mdio@f1000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,fman-xmdio"; + reg = <0xf1000 0x1000>; + interrupts = <100 1 0 0>; + }; |
