diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
5 files changed, 212 insertions, 5 deletions
diff --git a/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt b/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt index 4ff7128..c2546ce 100644 --- a/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt +++ b/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt @@ -45,6 +45,8 @@ Required properties: - #size-cells : <0> Optional properties: +- clock : reference to the clock for the NAND controller +- clock-names : "nand" (required for the above clock) - brcm,nand-has-wp : Some versions of this IP include a write-protect (WP) control bit. It is always available on >= v7.0. Use this property to describe the rare @@ -72,6 +74,12 @@ we define additional 'compatible' properties and associated register resources w and enable registers - reg-names: (required) "nand-int-base" + * "brcm,nand-bcm6368" + - compatible: should contain "brcm,nand-bcm<soc>", "brcm,nand-bcm6368" + - reg: (required) the 'NAND_INTR_BASE' register range, with combined status + and enable registers, and boot address registers + - reg-names: (required) "nand-int-base" + * "brcm,nand-iproc" - reg: (required) the "IDM" register range, for interrupt enable and APB bus access endianness configuration, and the "EXT" register range, @@ -148,3 +156,27 @@ nand@f0442800 { }; }; }; + +nand@10000200 { + compatible = "brcm,nand-bcm63168", "brcm,nand-bcm6368", + "brcm,brcmnand-v4.0", "brcm,brcmnand"; + reg = <0x10000200 0x180>, + <0x10000600 0x200>, + <0x100000b0 0x10>; + reg-names = "nand", "nand-cache", "nand-int-base"; + interrupt-parent = <&periph_intc>; + interrupts = <50>; + clocks = <&periph_clk 20>; + clock-names = "nand"; + + #address-cells = <1>; + #size-cells = <0>; + + nand0: nandcs@0 { + compatible = "brcm,nandcs"; + reg = <0>; + nand-on-flash-bbt; + nand-ecc-strength = <1>; + nand-ecc-step-size = <512>; + }; +}; diff --git a/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt b/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt new file mode 100644 index 0000000..29ea585 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt @@ -0,0 +1,86 @@ +* Ingenic JZ4780 NAND/BCH + +This file documents the device tree bindings for NAND flash devices on the +JZ4780. NAND devices are connected to the NEMC controller (described in +memory-controllers/ingenic,jz4780-nemc.txt), and thus NAND device nodes must +be children of the NEMC node. + +Required NAND controller device properties: +- compatible: Should be set to "ingenic,jz4780-nand". +- reg: For each bank with a NAND chip attached, should specify a bank number, + an offset of 0 and a size of 0x1000000 (i.e. the whole NEMC bank). + +Optional NAND controller device properties: +- ingenic,bch-controller: To make use of the hardware BCH controller, this + property must contain a phandle for the BCH controller node. The required + properties for this node are described below. If this is not specified, + software BCH will be used instead. + +Optional children nodes: +- Individual NAND chips are children of the NAND controller node. + +Required children node properties: +- reg: An integer ranging from 1 to 6 representing the CS line to use. + +Optional children node properties: +- nand-ecc-step-size: ECC block size in bytes. +- nand-ecc-strength: ECC strength (max number of correctable bits). +- nand-ecc-mode: String, operation mode of the NAND ecc mode. "hw" by default +- nand-on-flash-bbt: boolean to enable on flash bbt option, if not present false +- rb-gpios: GPIO specifier for the busy pin. +- wp-gpios: GPIO specifier for the write protect pin. + +Optional child node of NAND chip nodes: +- partitions: see Documentation/devicetree/bindings/mtd/partition.txt + +Example: + +nemc: nemc@13410000 { + ... + + nandc: nand-controller@1 { + compatible = "ingenic,jz4780-nand"; + reg = <1 0 0x1000000>; /* Bank 1 */ + + #address-cells = <1>; + #size-cells = <0>; + + ingenic,bch-controller = <&bch>; + + nand@1 { + reg = <1>; + + nand-ecc-step-size = <1024>; + nand-ecc-strength = <24>; + nand-ecc-mode = "hw"; + nand-on-flash-bbt; + + rb-gpios = <&gpa 20 GPIO_ACTIVE_LOW>; + wp-gpios = <&gpf 22 GPIO_ACTIVE_LOW>; + + partitions { + #address-cells = <2>; + #size-cells = <2>; + ... + } + }; + }; +}; + +The BCH controller is a separate SoC component used for error correction on +NAND devices. The following is a description of the device properties for a +BCH controller. + +Required BCH properties: +- compatible: Should be set to "ingenic,jz4780-bch". +- reg: Should specify the BCH controller registers location and length. +- clocks: Clock for the BCH controller. + +Example: + +bch: bch@134d0000 { + compatible = "ingenic,jz4780-bch"; + reg = <0x134d0000 0x10000>; + + clocks = <&cgu JZ4780_CLK_BCH>; +}; diff --git a/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt index 2bee681..2c91c03 100644 --- a/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt +++ b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt @@ -1,15 +1,61 @@ -* MTD SPI driver for ST M25Pxx (and similar) serial flash chips +* SPI NOR flash: ST M25Pxx (and similar) serial flash chips Required properties: - #address-cells, #size-cells : Must be present if the device has sub-nodes representing partitions. - compatible : May include a device-specific string consisting of the - manufacturer and name of the chip. Bear in mind the DT binding - is not Linux-only, but in case of Linux, see the "m25p_ids" - table in drivers/mtd/devices/m25p80.c for the list of supported - chips. + manufacturer and name of the chip. A list of supported chip + names follows. Must also include "jedec,spi-nor" for any SPI NOR flash that can be identified by the JEDEC READ ID opcode (0x9F). + + Supported chip names: + at25df321a + at25df641 + at26df081a + mr25h256 + mx25l4005a + mx25l1606e + mx25l6405d + mx25l12805d + mx25l25635e + n25q064 + n25q128a11 + n25q128a13 + n25q512a + s25fl256s1 + s25fl512s + s25sl12801 + s25fl008k + s25fl064k + sst25vf040b + m25p40 + m25p80 + m25p16 + m25p32 + m25p64 + m25p128 + w25x80 + w25x32 + w25q32 + w25q32dw + w25q80bl + w25q128 + w25q256 + + The following chip names have been used historically to + designate quirky versions of flash chips that do not support the + JEDEC READ ID opcode (0x9F): + m25p05-nonjedec + m25p10-nonjedec + m25p20-nonjedec + m25p40-nonjedec + m25p80-nonjedec + m25p16-nonjedec + m25p32-nonjedec + m25p64-nonjedec + m25p128-nonjedec + - reg : Chip-Select number - spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at diff --git a/Documentation/devicetree/bindings/mtd/mtk-quadspi.txt b/Documentation/devicetree/bindings/mtd/mtk-quadspi.txt new file mode 100644 index 0000000..fb314f0 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/mtk-quadspi.txt @@ -0,0 +1,41 @@ +* Serial NOR flash controller for MTK MT81xx (and similar) + +Required properties: +- compatible: should be "mediatek,mt8173-nor"; +- reg: physical base address and length of the controller's register +- clocks: the phandle of the clocks needed by the nor controller +- clock-names: the names of the clocks + the clocks should be named "spi" and "sf". "spi" is used for spi bus, + and "sf" is used for controller, these are the clocks witch + hardware needs to enabling nor flash and nor flash controller. + See Documentation/devicetree/bindings/clock/clock-bindings.txt for details. +- #address-cells: should be <1> +- #size-cells: should be <0> + +The SPI flash must be a child of the nor_flash node and must have a +compatible property. Also see jedec,spi-nor.txt. + +Required properties: +- compatible: May include a device-specific string consisting of the manufacturer + and name of the chip. Must also include "jedec,spi-nor" for any + SPI NOR flash that can be identified by the JEDEC READ ID opcode (0x9F). +- reg : Chip-Select number + +Example: + +nor_flash: spi@1100d000 { + compatible = "mediatek,mt8173-nor"; + reg = <0 0x1100d000 0 0xe0>; + clocks = <&pericfg CLK_PERI_SPI>, + <&topckgen CLK_TOP_SPINFI_IFR_SEL>; + clock-names = "spi", "sf"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + }; +}; + diff --git a/Documentation/devicetree/bindings/mtd/partition.txt b/Documentation/devicetree/bindings/mtd/partition.txt index 1c63e40..81a224d 100644 --- a/Documentation/devicetree/bindings/mtd/partition.txt +++ b/Documentation/devicetree/bindings/mtd/partition.txt @@ -32,6 +32,8 @@ Optional properties: partition should only be mounted read-only. This is usually used for flash partitions containing early-boot firmware images or data which should not be clobbered. +- lock : Do not unlock the partition at initialization time (not supported on + all devices) Examples: |