diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
5 files changed, 65 insertions, 44 deletions
diff --git a/Documentation/devicetree/bindings/iio/proximity/as3935.txt b/Documentation/devicetree/bindings/iio/proximity/as3935.txt index 38d7431..b6c1afa 100644 --- a/Documentation/devicetree/bindings/iio/proximity/as3935.txt +++ b/Documentation/devicetree/bindings/iio/proximity/as3935.txt @@ -16,6 +16,10 @@ Optional properties: - ams,tuning-capacitor-pf: Calibration tuning capacitor stepping value 0 - 120pF. This will require using the calibration data from the manufacturer. + - ams,nflwdth: Set the noise and watchdog threshold register on + startup. This will need to set according to the noise from the + MCU board, and possibly the local environment. Refer to the + datasheet for the threshold settings. Example: @@ -27,4 +31,5 @@ as3935@0 { interrupt-parent = <&gpio1>; interrupts = <16 1>; ams,tuning-capacitor-pf = <80>; + ams,nflwdth = <0x44>; }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt b/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt index 4c29cda..5eb108e 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt @@ -99,7 +99,7 @@ Examples: compatible = "arm,gic-v3-its"; msi-controller; #msi-cells = <1>; - reg = <0x0 0x2c200000 0 0x200000>; + reg = <0x0 0x2c200000 0 0x20000>; }; }; @@ -124,14 +124,14 @@ Examples: compatible = "arm,gic-v3-its"; msi-controller; #msi-cells = <1>; - reg = <0x0 0x2c200000 0 0x200000>; + reg = <0x0 0x2c200000 0 0x20000>; }; gic-its@2c400000 { compatible = "arm,gic-v3-its"; msi-controller; #msi-cells = <1>; - reg = <0x0 0x2c400000 0 0x200000>; + reg = <0x0 0x2c400000 0 0x20000>; }; ppi-partitions { diff --git a/Documentation/devicetree/bindings/mfd/arizona.txt b/Documentation/devicetree/bindings/mfd/arizona.txt index b37bdde..bdd0176 100644 --- a/Documentation/devicetree/bindings/mfd/arizona.txt +++ b/Documentation/devicetree/bindings/mfd/arizona.txt @@ -65,45 +65,6 @@ Optional properties: a value that is out of range for a 16 bit register then the chip default will be used. If present exactly five values must be specified. - - wlf,inmode : A list of INn_MODE register values, where n is the number - of input signals. Valid values are 0 (Differential), 1 (Single-ended) and - 2 (Digital Microphone). If absent, INn_MODE registers set to 0 by default. - If present, values must be specified less than or equal to the number of - input signals. If values less than the number of input signals, elements - that have not been specified are set to 0 by default. Entries are: - <IN1, IN2, IN3, IN4> (wm5102, wm5110, wm8280, wm8997) - <IN1A, IN2A, IN1B, IN2B> (wm8998, wm1814) - - wlf,out-mono : A list of boolean values indicating whether each output is - mono or stereo. Position within the list indicates the output affected - (eg. First entry in the list corresponds to output 1). A non-zero value - indicates a mono output. If present, the number of values should be less - than or equal to the number of outputs, if less values are supplied the - additional outputs will be treated as stereo. - - - wlf,dmic-ref : DMIC reference voltage source for each input, can be - selected from either MICVDD or one of the MICBIAS's, defines - (ARIZONA_DMIC_xxxx) are provided in <dt-bindings/mfd/arizona.txt>. If - present, the number of values should be less than or equal to the - number of inputs, unspecified inputs will use the chip default. - - - wlf,max-channels-clocked : The maximum number of channels to be clocked on - each AIF, useful for I2S systems with multiple data lines being mastered. - Specify one cell for each AIF to be configured, specify zero for AIFs that - should be handled normally. - If present, number of cells must be less than or equal to the number of - AIFs. If less than the number of AIFs, for cells that have not been - specified the corresponding AIFs will be treated as default setting. - - - wlf,spk-fmt : PDM speaker data format, must contain 2 cells (OUT5 and OUT6). - See the datasheet for values. - The second cell is ignored for codecs that do not have OUT6 (wm5102, wm8997, - wm8998, wm1814) - - - wlf,spk-mute : PDM speaker mute setting, must contain 2 cells (OUT5 and OUT6). - See the datasheet for values. - The second cell is ignored for codecs that do not have OUT6 (wm5102, wm8997, - wm8998, wm1814) - - DCVDD-supply, MICVDD-supply : Power supplies, only need to be specified if they are being externally supplied. As covered in Documentation/devicetree/bindings/regulator/regulator.txt @@ -112,6 +73,7 @@ Optional properties: Also see child specific device properties: Regulator - ../regulator/arizona-regulator.txt Extcon - ../extcon/extcon-arizona.txt + Sound - ../sound/arizona.txt Example: diff --git a/Documentation/devicetree/bindings/sound/audio-graph-scu-card.txt b/Documentation/devicetree/bindings/sound/audio-graph-scu-card.txt index 8b8afe9..441dd6f 100644 --- a/Documentation/devicetree/bindings/sound/audio-graph-scu-card.txt +++ b/Documentation/devicetree/bindings/sound/audio-graph-scu-card.txt @@ -43,7 +43,7 @@ Example 1. Sampling Rate Conversion label = "sound-card"; prefix = "codec"; routing = "codec Playback", "DAI0 Playback", - "codec Playback", "DAI1 Playback"; + "DAI0 Capture", "codec Capture"; convert-rate = <48000>; dais = <&cpu_port>; @@ -79,7 +79,8 @@ Example 2. 2 CPU 1 Codec (Mixing) label = "sound-card"; prefix = "codec"; routing = "codec Playback", "DAI0 Playback", - "codec Playback", "DAI1 Playback"; + "codec Playback", "DAI1 Playback", + "DAI0 Capture", "codec Capture"; convert-rate = <48000>; dais = <&cpu_port0 diff --git a/Documentation/devicetree/bindings/sound/wlf,arizona.txt b/Documentation/devicetree/bindings/sound/wlf,arizona.txt new file mode 100644 index 0000000..e172c62 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/wlf,arizona.txt @@ -0,0 +1,53 @@ +Cirrus Logic Arizona class audio SoCs + +These devices are audio SoCs with extensive digital capabilities and a range +of analogue I/O. + +This document lists sound specific bindings, see the primary binding +document: + ../mfd/arizona.txt + +Optional properties: + + - wlf,inmode : A list of INn_MODE register values, where n is the number + of input signals. Valid values are 0 (Differential), 1 (Single-ended) and + 2 (Digital Microphone). If absent, INn_MODE registers set to 0 by default. + If present, values must be specified less than or equal to the number of + input signals. If values less than the number of input signals, elements + that have not been specified are set to 0 by default. Entries are: + <IN1, IN2, IN3, IN4> (wm5102, wm5110, wm8280, wm8997) + <IN1A, IN2A, IN1B, IN2B> (wm8998, wm1814) + - wlf,out-mono : A list of boolean values indicating whether each output is + mono or stereo. Position within the list indicates the output affected + (eg. First entry in the list corresponds to output 1). A non-zero value + indicates a mono output. If present, the number of values should be less + than or equal to the number of outputs, if less values are supplied the + additional outputs will be treated as stereo. + + - wlf,dmic-ref : DMIC reference voltage source for each input, can be + selected from either MICVDD or one of the MICBIAS's, defines + (ARIZONA_DMIC_xxxx) are provided in <dt-bindings/mfd/arizona.txt>. If + present, the number of values should be less than or equal to the + number of inputs, unspecified inputs will use the chip default. + + - wlf,max-channels-clocked : The maximum number of channels to be clocked on + each AIF, useful for I2S systems with multiple data lines being mastered. + Specify one cell for each AIF to be configured, specify zero for AIFs that + should be handled normally. + If present, number of cells must be less than or equal to the number of + AIFs. If less than the number of AIFs, for cells that have not been + specified the corresponding AIFs will be treated as default setting. + + - wlf,spk-fmt : PDM speaker data format, must contain 2 cells (OUT5 and OUT6). + See the datasheet for values. + The second cell is ignored for codecs that do not have OUT6 (wm5102, wm8997, + wm8998, wm1814) + + - wlf,spk-mute : PDM speaker mute setting, must contain 2 cells (OUT5 and OUT6). + See the datasheet for values. + The second cell is ignored for codecs that do not have OUT6 (wm5102, wm8997, + wm8998, wm1814) + + - wlf,out-volume-limit : The volume limit value that should be applied to each + output channel. See the datasheet for exact values. Channels are specified + in the order OUT1L, OUT1R, OUT2L, OUT2R, etc. |