diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
6 files changed, 65 insertions, 50 deletions
diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt index 8b0328f..29e1dc5 100644 --- a/Documentation/devicetree/bindings/arm/cpus.txt +++ b/Documentation/devicetree/bindings/arm/cpus.txt @@ -199,6 +199,7 @@ described below. "actions,s500-smp" "allwinner,sun6i-a31" "allwinner,sun8i-a23" + "allwinner,sun9i-a80-smp" "amlogic,meson8-smp" "amlogic,meson8b-smp" "arm,realview-smp" diff --git a/Documentation/devicetree/bindings/arm/omap/mpu.txt b/Documentation/devicetree/bindings/arm/omap/mpu.txt index 763695d..f301e63 100644 --- a/Documentation/devicetree/bindings/arm/omap/mpu.txt +++ b/Documentation/devicetree/bindings/arm/omap/mpu.txt @@ -13,6 +13,13 @@ Required properties: Optional properties: - sram: Phandle to the ocmcram node +am335x and am437x only: +- pm-sram: Phandles to ocmcram nodes to be used for power management. + First should be type 'protect-exec' for the driver to use to copy + and run PM functions, second should be regular pool to be used for + data region for code. See Documentation/devicetree/bindings/sram/sram.txt + for more details. + Examples: - For an OMAP5 SMP system: @@ -36,3 +43,12 @@ mpu { compatible = "ti,omap3-mpu"; ti,hwmods = "mpu"; }; + +- For an AM335x system: + +mpu { + compatible = "ti,omap3-mpu"; + ti,hwmods = "mpu"; + pm-sram = <&pm_sram_code + &pm_sram_data>; +}; diff --git a/Documentation/devicetree/bindings/arm/sunxi/smp-sram.txt b/Documentation/devicetree/bindings/arm/sunxi/smp-sram.txt new file mode 100644 index 0000000..082e6a9 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/sunxi/smp-sram.txt @@ -0,0 +1,44 @@ +Allwinner SRAM for smp bringup: +------------------------------------------------ + +Allwinner's A80 SoC uses part of the secure sram for hotplugging of the +primary core (cpu0). Once the core gets powered up it checks if a magic +value is set at a specific location. If it is then the BROM will jump +to the software entry address, instead of executing a standard boot. + +Therefore a reserved section sub-node has to be added to the mmio-sram +declaration. + +Note that this is separate from the Allwinner SRAM controller found in +../../sram/sunxi-sram.txt. This SRAM is secure only and not mappable to +any device. + +Also there are no "secure-only" properties. The implementation should +check if this SRAM is usable first. + +Required sub-node properties: +- compatible : depending on the SoC this should be one of: + "allwinner,sun9i-a80-smp-sram" + +The rest of the properties should follow the generic mmio-sram discription +found in ../../misc/sram.txt + +Example: + + sram_b: sram@20000 { + /* 256 KiB secure SRAM at 0x20000 */ + compatible = "mmio-sram"; + reg = <0x00020000 0x40000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x00020000 0x40000>; + + smp-sram@1000 { + /* + * This is checked by BROM to determine if + * cpu0 should jump to SMP entry vector + */ + compatible = "allwinner,sun9i-a80-smp-sram"; + reg = <0x1000 0x8>; + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt b/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt deleted file mode 100644 index d4ee4da..0000000 --- a/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt +++ /dev/null @@ -1,50 +0,0 @@ -PXA3xx NAND DT bindings - -Required properties: - - - compatible: Should be set to one of the following: - marvell,pxa3xx-nand - marvell,armada370-nand - marvell,armada-8k-nand - - reg: The register base for the controller - - interrupts: The interrupt to map - - #address-cells: Set to <1> if the node includes partitions - - marvell,system-controller: Set to retrieve the syscon node that handles - NAND controller related registers (only required - with marvell,armada-8k-nand compatible). - -Optional properties: - - - dmas: dma data channel, see dma.txt binding doc - - marvell,nand-enable-arbiter: Set to enable the bus arbiter - - marvell,nand-keep-config: Set to keep the NAND controller config as set - by the bootloader - - num-cs: Number of chipselect lines to use - - nand-on-flash-bbt: boolean to enable on flash bbt option if - not present false - - nand-ecc-strength: number of bits to correct per ECC step - - nand-ecc-step-size: number of data bytes covered by a single ECC step - -The following ECC strength and step size are currently supported: - - - nand-ecc-strength = <1>, nand-ecc-step-size = <512> - - nand-ecc-strength = <4>, nand-ecc-step-size = <512> - - nand-ecc-strength = <8>, nand-ecc-step-size = <512> - -Example: - - nand0: nand@43100000 { - compatible = "marvell,pxa3xx-nand"; - reg = <0x43100000 90>; - interrupts = <45>; - dmas = <&pdma 97 0>; - dma-names = "data"; - #address-cells = <1>; - - marvell,nand-enable-arbiter; - marvell,nand-keep-config; - num-cs = <1>; - - /* partitions (optional) */ - }; - diff --git a/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt b/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt index 8690f10..ab399e5 100644 --- a/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt +++ b/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt @@ -17,7 +17,9 @@ Required properties: - "renesas,r8a7794-sysc" (R-Car E2) - "renesas,r8a7795-sysc" (R-Car H3) - "renesas,r8a7796-sysc" (R-Car M3-W) + - "renesas,r8a77965-sysc" (R-Car M3-N) - "renesas,r8a77970-sysc" (R-Car V3M) + - "renesas,r8a77980-sysc" (R-Car V3H) - "renesas,r8a77995-sysc" (R-Car D3) - reg: Address start and address range for the device. - #power-domain-cells: Must be 1. diff --git a/Documentation/devicetree/bindings/reset/renesas,rst.txt b/Documentation/devicetree/bindings/reset/renesas,rst.txt index a8014f3..294a0da 100644 --- a/Documentation/devicetree/bindings/reset/renesas,rst.txt +++ b/Documentation/devicetree/bindings/reset/renesas,rst.txt @@ -26,7 +26,9 @@ Required properties: - "renesas,r8a7794-rst" (R-Car E2) - "renesas,r8a7795-rst" (R-Car H3) - "renesas,r8a7796-rst" (R-Car M3-W) + - "renesas,r8a77965-rst" (R-Car M3-N) - "renesas,r8a77970-rst" (R-Car V3M) + - "renesas,r8a77980-rst" (R-Car V3H) - "renesas,r8a77995-rst" (R-Car D3) - reg: Address start and address range for the device. |
